Merge git://git.kernel.org/pub/scm/linux/kernel/git/wim/linux-2.6-watchdog
* git://git.kernel.org/pub/scm/linux/kernel/git/wim/linux-2.6-watchdog:
watchdog: iTCO_wdt.c: remove extra pci_dev_put()'s from init code
watchdog: add support for Broadcom BCM63xx built-in watchdog
watchdog: f71808e_wdt: add support for the F71889FG
watchdog: MachZ: fix debug macro
watchdog: it8712f_wdt: Add module parameter for alternative reset sources
watchdog: it8712f_wdt: Add comments for config/control register names
watchdog: it87_wdt: Add support for watchdogs with 8b timers
watchdog: it87_wdt: Add support for IT8720F watchdog
watchdog: Use static const char * const where possible
watchdog: iTCO_wdt: Cleanup warning messages
watchdog: iTCO_wdt: TCO Watchdog patch for Intel Patsburg DeviceIDs
diff --git a/Documentation/kbuild/makefiles.txt b/Documentation/kbuild/makefiles.txt
index c787ae5..0ef00bd 100644
--- a/Documentation/kbuild/makefiles.txt
+++ b/Documentation/kbuild/makefiles.txt
@@ -776,6 +776,13 @@
Kbuild will assume the directories to be in the same relative path as the
Makefile if no absolute path is specified (path does not start with '/').
+To exclude certain files from make clean, use the $(no-clean-files) variable.
+This is only a special case used in the top level Kbuild file:
+
+ Example:
+ #Kbuild
+ no-clean-files := $(bounds-file) $(offsets-file)
+
Usually kbuild descends down in subdirectories due to "obj-* := dir/",
but in the architecture makefiles where the kbuild infrastructure
is not sufficient this sometimes needs to be explicit.
diff --git a/Kbuild b/Kbuild
index b00037a..2114113 100644
--- a/Kbuild
+++ b/Kbuild
@@ -95,5 +95,5 @@
missing-syscalls: scripts/checksyscalls.sh FORCE
$(call cmd,syscalls)
-# Delete all targets during make clean
-clean-files := $(addprefix $(objtree)/,$(filter-out $(bounds-file) $(offsets-file),$(targets)))
+# Keep these two files during make clean
+no-clean-files := $(bounds-file) $(offsets-file)
diff --git a/Makefile b/Makefile
index 3e43805..6b23f1b 100644
--- a/Makefile
+++ b/Makefile
@@ -1137,21 +1137,13 @@
#
clean: rm-dirs := $(CLEAN_DIRS)
clean: rm-files := $(CLEAN_FILES)
-clean-dirs := $(addprefix _clean_,$(srctree) $(vmlinux-alldirs) Documentation)
+clean-dirs := $(addprefix _clean_, . $(vmlinux-alldirs) Documentation)
PHONY += $(clean-dirs) clean archclean
$(clean-dirs):
$(Q)$(MAKE) $(clean)=$(patsubst _clean_%,%,$@)
-clean: archclean $(clean-dirs)
- $(call cmd,rmdirs)
- $(call cmd,rmfiles)
- @find . $(RCS_FIND_IGNORE) \
- \( -name '*.[oas]' -o -name '*.ko' -o -name '.*.cmd' \
- -o -name '.*.d' -o -name '.*.tmp' -o -name '*.mod.c' \
- -o -name '*.symtypes' -o -name 'modules.order' \
- -o -name modules.builtin -o -name '.tmp_*.o.*' \
- -o -name '*.gcno' \) -type f -print | xargs rm -f
+clean: archclean
# mrproper - Delete all generated files, including .config
#
@@ -1352,16 +1344,7 @@
$(Q)$(MAKE) $(clean)=$(patsubst _clean_%,%,$@)
clean: rm-dirs := $(MODVERDIR)
-clean: rm-files := $(KBUILD_EXTMOD)/Module.symvers \
- $(KBUILD_EXTMOD)/modules.order \
- $(KBUILD_EXTMOD)/modules.builtin
-clean: $(clean-dirs)
- $(call cmd,rmdirs)
- $(call cmd,rmfiles)
- @find $(KBUILD_EXTMOD) $(RCS_FIND_IGNORE) \
- \( -name '*.[oas]' -o -name '*.ko' -o -name '.*.cmd' \
- -o -name '.*.d' -o -name '.*.tmp' -o -name '*.mod.c' \
- -o -name '*.gcno' \) -type f -print | xargs rm -f
+clean: rm-files := $(KBUILD_EXTMOD)/Module.symvers
help:
@echo ' Building external modules.'
@@ -1378,6 +1361,16 @@
scripts: ;
endif # KBUILD_EXTMOD
+clean: $(clean-dirs)
+ $(call cmd,rmdirs)
+ $(call cmd,rmfiles)
+ @find $(or $(KBUILD_EXTMOD), .) $(RCS_FIND_IGNORE) \
+ \( -name '*.[oas]' -o -name '*.ko' -o -name '.*.cmd' \
+ -o -name '.*.d' -o -name '.*.tmp' -o -name '*.mod.c' \
+ -o -name '*.symtypes' -o -name 'modules.order' \
+ -o -name modules.builtin -o -name '.tmp_*.o.*' \
+ -o -name '*.gcno' \) -type f -print | xargs rm -f
+
# Generate tags for editors
# ---------------------------------------------------------------------------
quiet_cmd_tags = GEN $@
diff --git a/drivers/regulator/Kconfig b/drivers/regulator/Kconfig
index 172951b..dd30e88 100644
--- a/drivers/regulator/Kconfig
+++ b/drivers/regulator/Kconfig
@@ -100,6 +100,14 @@
help
Say y here to support the voltage regulaltor of Maxim MAX8925 PMIC.
+config REGULATOR_MAX8952
+ tristate "Maxim MAX8952 Power Management IC"
+ depends on I2C
+ help
+ This driver controls a Maxim 8952 voltage output regulator
+ via I2C bus. Maxim 8952 has one voltage output and supports 4 DVS
+ modes ranging from 0.77V to 1.40V by 0.01V steps.
+
config REGULATOR_MAX8998
tristate "Maxim 8998 voltage regulator"
depends on MFD_MAX8998
@@ -164,6 +172,13 @@
Say Y here to support the voltage regulators and convertors
on National Semiconductors LP3971 PMIC
+config REGULATOR_LP3972
+ tristate "National Semiconductors LP3972 PMIC regulator driver"
+ depends on I2C
+ help
+ Say Y here to support the voltage regulators and convertors
+ on National Semiconductors LP3972 PMIC
+
config REGULATOR_PCAP
tristate "PCAP2 regulator driver"
depends on EZX_PCAP
diff --git a/drivers/regulator/Makefile b/drivers/regulator/Makefile
index 8285fd8..bff8157 100644
--- a/drivers/regulator/Makefile
+++ b/drivers/regulator/Makefile
@@ -3,20 +3,21 @@
#
-obj-$(CONFIG_REGULATOR) += core.o
+obj-$(CONFIG_REGULATOR) += core.o dummy.o
obj-$(CONFIG_REGULATOR_FIXED_VOLTAGE) += fixed.o
obj-$(CONFIG_REGULATOR_VIRTUAL_CONSUMER) += virtual.o
obj-$(CONFIG_REGULATOR_USERSPACE_CONSUMER) += userspace-consumer.o
obj-$(CONFIG_REGULATOR_AD5398) += ad5398.o
obj-$(CONFIG_REGULATOR_BQ24022) += bq24022.o
-obj-$(CONFIG_REGULATOR_DUMMY) += dummy.o
obj-$(CONFIG_REGULATOR_LP3971) += lp3971.o
+obj-$(CONFIG_REGULATOR_LP3972) += lp3972.o
obj-$(CONFIG_REGULATOR_MAX1586) += max1586.o
obj-$(CONFIG_REGULATOR_TWL4030) += twl-regulator.o
obj-$(CONFIG_REGULATOR_MAX8649) += max8649.o
obj-$(CONFIG_REGULATOR_MAX8660) += max8660.o
obj-$(CONFIG_REGULATOR_MAX8925) += max8925-regulator.o
+obj-$(CONFIG_REGULATOR_MAX8952) += max8952.o
obj-$(CONFIG_REGULATOR_MAX8998) += max8998.o
obj-$(CONFIG_REGULATOR_WM831X) += wm831x-dcdc.o
obj-$(CONFIG_REGULATOR_WM831X) += wm831x-isink.o
diff --git a/drivers/regulator/core.c b/drivers/regulator/core.c
index cc8b337..f1d10c9 100644
--- a/drivers/regulator/core.c
+++ b/drivers/regulator/core.c
@@ -33,6 +33,7 @@
static LIST_HEAD(regulator_list);
static LIST_HEAD(regulator_map_list);
static int has_full_constraints;
+static bool board_wants_dummy_regulator;
/*
* struct regulator_map
@@ -63,7 +64,8 @@
};
static int _regulator_is_enabled(struct regulator_dev *rdev);
-static int _regulator_disable(struct regulator_dev *rdev);
+static int _regulator_disable(struct regulator_dev *rdev,
+ struct regulator_dev **supply_rdev_ptr);
static int _regulator_get_voltage(struct regulator_dev *rdev);
static int _regulator_get_current_limit(struct regulator_dev *rdev);
static unsigned int _regulator_get_mode(struct regulator_dev *rdev);
@@ -1108,6 +1110,11 @@
}
}
+ if (board_wants_dummy_regulator) {
+ rdev = dummy_regulator_rdev;
+ goto found;
+ }
+
#ifdef CONFIG_REGULATOR_DUMMY
if (!devname)
devname = "deviceless";
@@ -1348,7 +1355,8 @@
EXPORT_SYMBOL_GPL(regulator_enable);
/* locks held by regulator_disable() */
-static int _regulator_disable(struct regulator_dev *rdev)
+static int _regulator_disable(struct regulator_dev *rdev,
+ struct regulator_dev **supply_rdev_ptr)
{
int ret = 0;
@@ -1376,8 +1384,7 @@
}
/* decrease our supplies ref count and disable if required */
- if (rdev->supply)
- _regulator_disable(rdev->supply);
+ *supply_rdev_ptr = rdev->supply;
rdev->use_count = 0;
} else if (rdev->use_count > 1) {
@@ -1407,17 +1414,29 @@
int regulator_disable(struct regulator *regulator)
{
struct regulator_dev *rdev = regulator->rdev;
+ struct regulator_dev *supply_rdev = NULL;
int ret = 0;
mutex_lock(&rdev->mutex);
- ret = _regulator_disable(rdev);
+ ret = _regulator_disable(rdev, &supply_rdev);
mutex_unlock(&rdev->mutex);
+
+ /* decrease our supplies ref count and disable if required */
+ while (supply_rdev != NULL) {
+ rdev = supply_rdev;
+
+ mutex_lock(&rdev->mutex);
+ _regulator_disable(rdev, &supply_rdev);
+ mutex_unlock(&rdev->mutex);
+ }
+
return ret;
}
EXPORT_SYMBOL_GPL(regulator_disable);
/* locks held by regulator_force_disable() */
-static int _regulator_force_disable(struct regulator_dev *rdev)
+static int _regulator_force_disable(struct regulator_dev *rdev,
+ struct regulator_dev **supply_rdev_ptr)
{
int ret = 0;
@@ -1436,8 +1455,7 @@
}
/* decrease our supplies ref count and disable if required */
- if (rdev->supply)
- _regulator_disable(rdev->supply);
+ *supply_rdev_ptr = rdev->supply;
rdev->use_count = 0;
return ret;
@@ -1454,12 +1472,17 @@
*/
int regulator_force_disable(struct regulator *regulator)
{
+ struct regulator_dev *supply_rdev = NULL;
int ret;
mutex_lock(®ulator->rdev->mutex);
regulator->uA_load = 0;
- ret = _regulator_force_disable(regulator->rdev);
+ ret = _regulator_force_disable(regulator->rdev, &supply_rdev);
mutex_unlock(®ulator->rdev->mutex);
+
+ if (supply_rdev)
+ regulator_disable(get_device_regulator(rdev_get_dev(supply_rdev)));
+
return ret;
}
EXPORT_SYMBOL_GPL(regulator_force_disable);
@@ -2463,6 +2486,22 @@
EXPORT_SYMBOL_GPL(regulator_has_full_constraints);
/**
+ * regulator_use_dummy_regulator - Provide a dummy regulator when none is found
+ *
+ * Calling this function will cause the regulator API to provide a
+ * dummy regulator to consumers if no physical regulator is found,
+ * allowing most consumers to proceed as though a regulator were
+ * configured. This allows systems such as those with software
+ * controllable regulators for the CPU core only to be brought up more
+ * readily.
+ */
+void regulator_use_dummy_regulator(void)
+{
+ board_wants_dummy_regulator = true;
+}
+EXPORT_SYMBOL_GPL(regulator_use_dummy_regulator);
+
+/**
* rdev_get_drvdata - get rdev regulator driver data
* @rdev: regulator
*
diff --git a/drivers/regulator/dummy.h b/drivers/regulator/dummy.h
index 3921c0e..97a11b7 100644
--- a/drivers/regulator/dummy.h
+++ b/drivers/regulator/dummy.h
@@ -22,10 +22,6 @@
extern struct regulator_dev *dummy_regulator_rdev;
-#ifdef CONFIG_REGULATOR_DUMMY
void __init regulator_dummy_init(void);
-#else
-static inline void regulator_dummy_init(void) { }
-#endif
#endif
diff --git a/drivers/regulator/lp3972.c b/drivers/regulator/lp3972.c
new file mode 100644
index 0000000..e07062f
--- /dev/null
+++ b/drivers/regulator/lp3972.c
@@ -0,0 +1,660 @@
+/*
+ * Regulator driver for National Semiconductors LP3972 PMIC chip
+ *
+ * Based on lp3971.c
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ *
+ */
+
+#include <linux/bug.h>
+#include <linux/err.h>
+#include <linux/i2c.h>
+#include <linux/kernel.h>
+#include <linux/regulator/driver.h>
+#include <linux/regulator/lp3972.h>
+#include <linux/slab.h>
+
+struct lp3972 {
+ struct device *dev;
+ struct mutex io_lock;
+ struct i2c_client *i2c;
+ int num_regulators;
+ struct regulator_dev **rdev;
+};
+
+/* LP3972 Control Registers */
+#define LP3972_SCR_REG 0x07
+#define LP3972_OVER1_REG 0x10
+#define LP3972_OVSR1_REG 0x11
+#define LP3972_OVER2_REG 0x12
+#define LP3972_OVSR2_REG 0x13
+#define LP3972_VCC1_REG 0x20
+#define LP3972_ADTV1_REG 0x23
+#define LP3972_ADTV2_REG 0x24
+#define LP3972_AVRC_REG 0x25
+#define LP3972_CDTC1_REG 0x26
+#define LP3972_CDTC2_REG 0x27
+#define LP3972_SDTV1_REG 0x29
+#define LP3972_SDTV2_REG 0x2A
+#define LP3972_MDTV1_REG 0x32
+#define LP3972_MDTV2_REG 0x33
+#define LP3972_L2VCR_REG 0x39
+#define LP3972_L34VCR_REG 0x3A
+#define LP3972_SCR1_REG 0x80
+#define LP3972_SCR2_REG 0x81
+#define LP3972_OEN3_REG 0x82
+#define LP3972_OSR3_REG 0x83
+#define LP3972_LOER4_REG 0x84
+#define LP3972_B2TV_REG 0x85
+#define LP3972_B3TV_REG 0x86
+#define LP3972_B32RC_REG 0x87
+#define LP3972_ISRA_REG 0x88
+#define LP3972_BCCR_REG 0x89
+#define LP3972_II1RR_REG 0x8E
+#define LP3972_II2RR_REG 0x8F
+
+#define LP3972_SYS_CONTROL1_REG LP3972_SCR1_REG
+/* System control register 1 initial value,
+ * bits 5, 6 and 7 are EPROM programmable */
+#define SYS_CONTROL1_INIT_VAL 0x02
+#define SYS_CONTROL1_INIT_MASK 0x1F
+
+#define LP3972_VOL_CHANGE_REG LP3972_VCC1_REG
+#define LP3972_VOL_CHANGE_FLAG_GO 0x01
+#define LP3972_VOL_CHANGE_FLAG_MASK 0x03
+
+/* LDO output enable mask */
+#define LP3972_OEN3_L1EN BIT(0)
+#define LP3972_OVER2_LDO2_EN BIT(2)
+#define LP3972_OVER2_LDO3_EN BIT(3)
+#define LP3972_OVER2_LDO4_EN BIT(4)
+#define LP3972_OVER1_S_EN BIT(2)
+
+static const int ldo1_voltage_map[] = {
+ 1700, 1725, 1750, 1775, 1800, 1825, 1850, 1875,
+ 1900, 1925, 1950, 1975, 2000,
+};
+
+static const int ldo23_voltage_map[] = {
+ 1800, 1900, 2000, 2100, 2200, 2300, 2400, 2500,
+ 2600, 2700, 2800, 2900, 3000, 3100, 3200, 3300,
+};
+
+static const int ldo4_voltage_map[] = {
+ 1000, 1050, 1100, 1150, 1200, 1250, 1300, 1350,
+ 1400, 1500, 1800, 1900, 2500, 2800, 3000, 3300,
+};
+
+static const int ldo5_voltage_map[] = {
+ 0, 0, 0, 0, 0, 850, 875, 900,
+ 925, 950, 975, 1000, 1025, 1050, 1075, 1100,
+ 1125, 1150, 1175, 1200, 1225, 1250, 1275, 1300,
+ 1325, 1350, 1375, 1400, 1425, 1450, 1475, 1500,
+};
+
+static const int buck1_voltage_map[] = {
+ 725, 750, 775, 800, 825, 850, 875, 900,
+ 925, 950, 975, 1000, 1025, 1050, 1075, 1100,
+ 1125, 1150, 1175, 1200, 1225, 1250, 1275, 1300,
+ 1325, 1350, 1375, 1400, 1425, 1450, 1475, 1500,
+};
+
+static const int buck23_voltage_map[] = {
+ 0, 800, 850, 900, 950, 1000, 1050, 1100,
+ 1150, 1200, 1250, 1300, 1350, 1400, 1450, 1500,
+ 1550, 1600, 1650, 1700, 1800, 1900, 2500, 2800,
+ 3000, 3300,
+};
+
+static const int *ldo_voltage_map[] = {
+ ldo1_voltage_map,
+ ldo23_voltage_map,
+ ldo23_voltage_map,
+ ldo4_voltage_map,
+ ldo5_voltage_map,
+};
+
+static const int *buck_voltage_map[] = {
+ buck1_voltage_map,
+ buck23_voltage_map,
+ buck23_voltage_map,
+};
+
+static const int ldo_output_enable_mask[] = {
+ LP3972_OEN3_L1EN,
+ LP3972_OVER2_LDO2_EN,
+ LP3972_OVER2_LDO3_EN,
+ LP3972_OVER2_LDO4_EN,
+ LP3972_OVER1_S_EN,
+};
+
+static const int ldo_output_enable_addr[] = {
+ LP3972_OEN3_REG,
+ LP3972_OVER2_REG,
+ LP3972_OVER2_REG,
+ LP3972_OVER2_REG,
+ LP3972_OVER1_REG,
+};
+
+static const int ldo_vol_ctl_addr[] = {
+ LP3972_MDTV1_REG,
+ LP3972_L2VCR_REG,
+ LP3972_L34VCR_REG,
+ LP3972_L34VCR_REG,
+ LP3972_SDTV1_REG,
+};
+
+static const int buck_vol_enable_addr[] = {
+ LP3972_OVER1_REG,
+ LP3972_OEN3_REG,
+ LP3972_OEN3_REG,
+};
+
+static const int buck_base_addr[] = {
+ LP3972_ADTV1_REG,
+ LP3972_B2TV_REG,
+ LP3972_B3TV_REG,
+};
+
+#define LP3972_LDO_VOL_VALUE_MAP(x) (ldo_voltage_map[x])
+#define LP3972_LDO_OUTPUT_ENABLE_MASK(x) (ldo_output_enable_mask[x])
+#define LP3972_LDO_OUTPUT_ENABLE_REG(x) (ldo_output_enable_addr[x])
+
+/* LDO voltage control registers shift:
+ LP3972_LDO1 -> 0, LP3972_LDO2 -> 4
+ LP3972_LDO3 -> 0, LP3972_LDO4 -> 4
+ LP3972_LDO5 -> 0
+*/
+#define LP3972_LDO_VOL_CONTR_SHIFT(x) (((x) & 1) << 2)
+#define LP3972_LDO_VOL_CONTR_REG(x) (ldo_vol_ctl_addr[x])
+#define LP3972_LDO_VOL_CHANGE_SHIFT(x) ((x) ? 4 : 6)
+
+#define LP3972_LDO_VOL_MASK(x) (((x) % 4) ? 0x0f : 0x1f)
+#define LP3972_LDO_VOL_MIN_IDX(x) (((x) == 4) ? 0x05 : 0x00)
+#define LP3972_LDO_VOL_MAX_IDX(x) ((x) ? (((x) == 4) ? 0x1f : 0x0f) : 0x0c)
+
+#define LP3972_BUCK_VOL_VALUE_MAP(x) (buck_voltage_map[x])
+#define LP3972_BUCK_VOL_ENABLE_REG(x) (buck_vol_enable_addr[x])
+#define LP3972_BUCK_VOL1_REG(x) (buck_base_addr[x])
+#define LP3972_BUCK_VOL_MASK 0x1f
+#define LP3972_BUCK_VOL_MIN_IDX(x) ((x) ? 0x01 : 0x00)
+#define LP3972_BUCK_VOL_MAX_IDX(x) ((x) ? 0x19 : 0x1f)
+
+static int lp3972_i2c_read(struct i2c_client *i2c, char reg, int count,
+ u16 *dest)
+{
+ int ret;
+
+ if (count != 1)
+ return -EIO;
+ ret = i2c_smbus_read_byte_data(i2c, reg);
+ if (ret < 0)
+ return ret;
+
+ *dest = ret;
+ return 0;
+}
+
+static int lp3972_i2c_write(struct i2c_client *i2c, char reg, int count,
+ const u16 *src)
+{
+ if (count != 1)
+ return -EIO;
+ return i2c_smbus_write_byte_data(i2c, reg, *src);
+}
+
+static u8 lp3972_reg_read(struct lp3972 *lp3972, u8 reg)
+{
+ u16 val = 0;
+
+ mutex_lock(&lp3972->io_lock);
+
+ lp3972_i2c_read(lp3972->i2c, reg, 1, &val);
+
+ dev_dbg(lp3972->dev, "reg read 0x%02x -> 0x%02x\n", (int)reg,
+ (unsigned)val & 0xff);
+
+ mutex_unlock(&lp3972->io_lock);
+
+ return val & 0xff;
+}
+
+static int lp3972_set_bits(struct lp3972 *lp3972, u8 reg, u16 mask, u16 val)
+{
+ u16 tmp;
+ int ret;
+
+ mutex_lock(&lp3972->io_lock);
+
+ ret = lp3972_i2c_read(lp3972->i2c, reg, 1, &tmp);
+ tmp = (tmp & ~mask) | val;
+ if (ret == 0) {
+ ret = lp3972_i2c_write(lp3972->i2c, reg, 1, &tmp);
+ dev_dbg(lp3972->dev, "reg write 0x%02x -> 0x%02x\n", (int)reg,
+ (unsigned)val & 0xff);
+ }
+ mutex_unlock(&lp3972->io_lock);
+
+ return ret;
+}
+
+static int lp3972_ldo_list_voltage(struct regulator_dev *dev, unsigned index)
+{
+ int ldo = rdev_get_id(dev) - LP3972_LDO1;
+ return 1000 * LP3972_LDO_VOL_VALUE_MAP(ldo)[index];
+}
+
+static int lp3972_ldo_is_enabled(struct regulator_dev *dev)
+{
+ struct lp3972 *lp3972 = rdev_get_drvdata(dev);
+ int ldo = rdev_get_id(dev) - LP3972_LDO1;
+ u16 mask = LP3972_LDO_OUTPUT_ENABLE_MASK(ldo);
+ u16 val;
+
+ val = lp3972_reg_read(lp3972, LP3972_LDO_OUTPUT_ENABLE_REG(ldo));
+ return !!(val & mask);
+}
+
+static int lp3972_ldo_enable(struct regulator_dev *dev)
+{
+ struct lp3972 *lp3972 = rdev_get_drvdata(dev);
+ int ldo = rdev_get_id(dev) - LP3972_LDO1;
+ u16 mask = LP3972_LDO_OUTPUT_ENABLE_MASK(ldo);
+
+ return lp3972_set_bits(lp3972, LP3972_LDO_OUTPUT_ENABLE_REG(ldo),
+ mask, mask);
+}
+
+static int lp3972_ldo_disable(struct regulator_dev *dev)
+{
+ struct lp3972 *lp3972 = rdev_get_drvdata(dev);
+ int ldo = rdev_get_id(dev) - LP3972_LDO1;
+ u16 mask = LP3972_LDO_OUTPUT_ENABLE_MASK(ldo);
+
+ return lp3972_set_bits(lp3972, LP3972_LDO_OUTPUT_ENABLE_REG(ldo),
+ mask, 0);
+}
+
+static int lp3972_ldo_get_voltage(struct regulator_dev *dev)
+{
+ struct lp3972 *lp3972 = rdev_get_drvdata(dev);
+ int ldo = rdev_get_id(dev) - LP3972_LDO1;
+ u16 mask = LP3972_LDO_VOL_MASK(ldo);
+ u16 val, reg;
+
+ reg = lp3972_reg_read(lp3972, LP3972_LDO_VOL_CONTR_REG(ldo));
+ val = (reg >> LP3972_LDO_VOL_CONTR_SHIFT(ldo)) & mask;
+
+ return 1000 * LP3972_LDO_VOL_VALUE_MAP(ldo)[val];
+}
+
+static int lp3972_ldo_set_voltage(struct regulator_dev *dev,
+ int min_uV, int max_uV)
+{
+ struct lp3972 *lp3972 = rdev_get_drvdata(dev);
+ int ldo = rdev_get_id(dev) - LP3972_LDO1;
+ int min_vol = min_uV / 1000, max_vol = max_uV / 1000;
+ const int *vol_map = LP3972_LDO_VOL_VALUE_MAP(ldo);
+ u16 val;
+ int shift, ret;
+
+ if (min_vol < vol_map[LP3972_LDO_VOL_MIN_IDX(ldo)] ||
+ min_vol > vol_map[LP3972_LDO_VOL_MAX_IDX(ldo)])
+ return -EINVAL;
+
+ for (val = LP3972_LDO_VOL_MIN_IDX(ldo);
+ val <= LP3972_LDO_VOL_MAX_IDX(ldo); val++)
+ if (vol_map[val] >= min_vol)
+ break;
+
+ if (val > LP3972_LDO_VOL_MAX_IDX(ldo) || vol_map[val] > max_vol)
+ return -EINVAL;
+
+ shift = LP3972_LDO_VOL_CONTR_SHIFT(ldo);
+ ret = lp3972_set_bits(lp3972, LP3972_LDO_VOL_CONTR_REG(ldo),
+ LP3972_LDO_VOL_MASK(ldo) << shift, val << shift);
+
+ if (ret)
+ return ret;
+
+ /*
+ * LDO1 and LDO5 support voltage control by either target voltage1
+ * or target voltage2 register.
+ * We use target voltage1 register for LDO1 and LDO5 in this driver.
+ * We need to update voltage change control register(0x20) to enable
+ * LDO1 and LDO5 to change to their programmed target values.
+ */
+ switch (ldo) {
+ case LP3972_LDO1:
+ case LP3972_LDO5:
+ shift = LP3972_LDO_VOL_CHANGE_SHIFT(ldo);
+ ret = lp3972_set_bits(lp3972, LP3972_VOL_CHANGE_REG,
+ LP3972_VOL_CHANGE_FLAG_MASK << shift,
+ LP3972_VOL_CHANGE_FLAG_GO << shift);
+ if (ret)
+ return ret;
+
+ ret = lp3972_set_bits(lp3972, LP3972_VOL_CHANGE_REG,
+ LP3972_VOL_CHANGE_FLAG_MASK << shift, 0);
+ break;
+ }
+
+ return ret;
+}
+
+static struct regulator_ops lp3972_ldo_ops = {
+ .list_voltage = lp3972_ldo_list_voltage,
+ .is_enabled = lp3972_ldo_is_enabled,
+ .enable = lp3972_ldo_enable,
+ .disable = lp3972_ldo_disable,
+ .get_voltage = lp3972_ldo_get_voltage,
+ .set_voltage = lp3972_ldo_set_voltage,
+};
+
+static int lp3972_dcdc_list_voltage(struct regulator_dev *dev, unsigned index)
+{
+ int buck = rdev_get_id(dev) - LP3972_DCDC1;
+ return 1000 * buck_voltage_map[buck][index];
+}
+
+static int lp3972_dcdc_is_enabled(struct regulator_dev *dev)
+{
+ struct lp3972 *lp3972 = rdev_get_drvdata(dev);
+ int buck = rdev_get_id(dev) - LP3972_DCDC1;
+ u16 mask = 1 << (buck * 2);
+ u16 val;
+
+ val = lp3972_reg_read(lp3972, LP3972_BUCK_VOL_ENABLE_REG(buck));
+ return !!(val & mask);
+}
+
+static int lp3972_dcdc_enable(struct regulator_dev *dev)
+{
+ struct lp3972 *lp3972 = rdev_get_drvdata(dev);
+ int buck = rdev_get_id(dev) - LP3972_DCDC1;
+ u16 mask = 1 << (buck * 2);
+ u16 val;
+
+ val = lp3972_set_bits(lp3972, LP3972_BUCK_VOL_ENABLE_REG(buck),
+ mask, mask);
+ return val;
+}
+
+static int lp3972_dcdc_disable(struct regulator_dev *dev)
+{
+ struct lp3972 *lp3972 = rdev_get_drvdata(dev);
+ int buck = rdev_get_id(dev) - LP3972_DCDC1;
+ u16 mask = 1 << (buck * 2);
+ u16 val;
+
+ val = lp3972_set_bits(lp3972, LP3972_BUCK_VOL_ENABLE_REG(buck),
+ mask, 0);
+ return val;
+}
+
+static int lp3972_dcdc_get_voltage(struct regulator_dev *dev)
+{
+ struct lp3972 *lp3972 = rdev_get_drvdata(dev);
+ int buck = rdev_get_id(dev) - LP3972_DCDC1;
+ u16 reg;
+ int val;
+
+ reg = lp3972_reg_read(lp3972, LP3972_BUCK_VOL1_REG(buck));
+ reg &= LP3972_BUCK_VOL_MASK;
+ if (reg <= LP3972_BUCK_VOL_MAX_IDX(buck))
+ val = 1000 * buck_voltage_map[buck][reg];
+ else {
+ val = 0;
+ dev_warn(&dev->dev, "chip reported incorrect voltage value."
+ " reg = %d\n", reg);
+ }
+
+ return val;
+}
+
+static int lp3972_dcdc_set_voltage(struct regulator_dev *dev,
+ int min_uV, int max_uV)
+{
+ struct lp3972 *lp3972 = rdev_get_drvdata(dev);
+ int buck = rdev_get_id(dev) - LP3972_DCDC1;
+ int min_vol = min_uV / 1000, max_vol = max_uV / 1000;
+ const int *vol_map = buck_voltage_map[buck];
+ u16 val;
+ int ret;
+
+ if (min_vol < vol_map[LP3972_BUCK_VOL_MIN_IDX(buck)] ||
+ min_vol > vol_map[LP3972_BUCK_VOL_MAX_IDX(buck)])
+ return -EINVAL;
+
+ for (val = LP3972_BUCK_VOL_MIN_IDX(buck);
+ val <= LP3972_BUCK_VOL_MAX_IDX(buck); val++)
+ if (vol_map[val] >= min_vol)
+ break;
+
+ if (val > LP3972_BUCK_VOL_MAX_IDX(buck) ||
+ vol_map[val] > max_vol)
+ return -EINVAL;
+
+ ret = lp3972_set_bits(lp3972, LP3972_BUCK_VOL1_REG(buck),
+ LP3972_BUCK_VOL_MASK, val);
+ if (ret)
+ return ret;
+
+ if (buck != 0)
+ return ret;
+
+ ret = lp3972_set_bits(lp3972, LP3972_VOL_CHANGE_REG,
+ LP3972_VOL_CHANGE_FLAG_MASK, LP3972_VOL_CHANGE_FLAG_GO);
+ if (ret)
+ return ret;
+
+ return lp3972_set_bits(lp3972, LP3972_VOL_CHANGE_REG,
+ LP3972_VOL_CHANGE_FLAG_MASK, 0);
+}
+
+static struct regulator_ops lp3972_dcdc_ops = {
+ .list_voltage = lp3972_dcdc_list_voltage,
+ .is_enabled = lp3972_dcdc_is_enabled,
+ .enable = lp3972_dcdc_enable,
+ .disable = lp3972_dcdc_disable,
+ .get_voltage = lp3972_dcdc_get_voltage,
+ .set_voltage = lp3972_dcdc_set_voltage,
+};
+
+static struct regulator_desc regulators[] = {
+ {
+ .name = "LDO1",
+ .id = LP3972_LDO1,
+ .ops = &lp3972_ldo_ops,
+ .n_voltages = ARRAY_SIZE(ldo1_voltage_map),
+ .type = REGULATOR_VOLTAGE,
+ .owner = THIS_MODULE,
+ },
+ {
+ .name = "LDO2",
+ .id = LP3972_LDO2,
+ .ops = &lp3972_ldo_ops,
+ .n_voltages = ARRAY_SIZE(ldo23_voltage_map),
+ .type = REGULATOR_VOLTAGE,
+ .owner = THIS_MODULE,
+ },
+ {
+ .name = "LDO3",
+ .id = LP3972_LDO3,
+ .ops = &lp3972_ldo_ops,
+ .n_voltages = ARRAY_SIZE(ldo23_voltage_map),
+ .type = REGULATOR_VOLTAGE,
+ .owner = THIS_MODULE,
+ },
+ {
+ .name = "LDO4",
+ .id = LP3972_LDO4,
+ .ops = &lp3972_ldo_ops,
+ .n_voltages = ARRAY_SIZE(ldo4_voltage_map),
+ .type = REGULATOR_VOLTAGE,
+ .owner = THIS_MODULE,
+ },
+ {
+ .name = "LDO5",
+ .id = LP3972_LDO5,
+ .ops = &lp3972_ldo_ops,
+ .n_voltages = ARRAY_SIZE(ldo5_voltage_map),
+ .type = REGULATOR_VOLTAGE,
+ .owner = THIS_MODULE,
+ },
+ {
+ .name = "DCDC1",
+ .id = LP3972_DCDC1,
+ .ops = &lp3972_dcdc_ops,
+ .n_voltages = ARRAY_SIZE(buck1_voltage_map),
+ .type = REGULATOR_VOLTAGE,
+ .owner = THIS_MODULE,
+ },
+ {
+ .name = "DCDC2",
+ .id = LP3972_DCDC2,
+ .ops = &lp3972_dcdc_ops,
+ .n_voltages = ARRAY_SIZE(buck23_voltage_map),
+ .type = REGULATOR_VOLTAGE,
+ .owner = THIS_MODULE,
+ },
+ {
+ .name = "DCDC3",
+ .id = LP3972_DCDC3,
+ .ops = &lp3972_dcdc_ops,
+ .n_voltages = ARRAY_SIZE(buck23_voltage_map),
+ .type = REGULATOR_VOLTAGE,
+ .owner = THIS_MODULE,
+ },
+};
+
+static int __devinit setup_regulators(struct lp3972 *lp3972,
+ struct lp3972_platform_data *pdata)
+{
+ int i, err;
+
+ lp3972->num_regulators = pdata->num_regulators;
+ lp3972->rdev = kcalloc(pdata->num_regulators,
+ sizeof(struct regulator_dev *), GFP_KERNEL);
+ if (!lp3972->rdev) {
+ err = -ENOMEM;
+ goto err_nomem;
+ }
+
+ /* Instantiate the regulators */
+ for (i = 0; i < pdata->num_regulators; i++) {
+ struct lp3972_regulator_subdev *reg = &pdata->regulators[i];
+ lp3972->rdev[i] = regulator_register(®ulators[reg->id],
+ lp3972->dev, reg->initdata, lp3972);
+
+ if (IS_ERR(lp3972->rdev[i])) {
+ err = PTR_ERR(lp3972->rdev[i]);
+ dev_err(lp3972->dev, "regulator init failed: %d\n",
+ err);
+ goto error;
+ }
+ }
+
+ return 0;
+error:
+ while (--i >= 0)
+ regulator_unregister(lp3972->rdev[i]);
+ kfree(lp3972->rdev);
+ lp3972->rdev = NULL;
+err_nomem:
+ return err;
+}
+
+static int __devinit lp3972_i2c_probe(struct i2c_client *i2c,
+ const struct i2c_device_id *id)
+{
+ struct lp3972 *lp3972;
+ struct lp3972_platform_data *pdata = i2c->dev.platform_data;
+ int ret;
+ u16 val;
+
+ if (!pdata) {
+ dev_dbg(&i2c->dev, "No platform init data supplied\n");
+ return -ENODEV;
+ }
+
+ lp3972 = kzalloc(sizeof(struct lp3972), GFP_KERNEL);
+ if (!lp3972)
+ return -ENOMEM;
+
+ lp3972->i2c = i2c;
+ lp3972->dev = &i2c->dev;
+
+ mutex_init(&lp3972->io_lock);
+
+ /* Detect LP3972 */
+ ret = lp3972_i2c_read(i2c, LP3972_SYS_CONTROL1_REG, 1, &val);
+ if (ret == 0 &&
+ (val & SYS_CONTROL1_INIT_MASK) != SYS_CONTROL1_INIT_VAL) {
+ ret = -ENODEV;
+ dev_err(&i2c->dev, "chip reported: val = 0x%x\n", val);
+ }
+ if (ret < 0) {
+ dev_err(&i2c->dev, "failed to detect device. ret = %d\n", ret);
+ goto err_detect;
+ }
+
+ ret = setup_regulators(lp3972, pdata);
+ if (ret < 0)
+ goto err_detect;
+
+ i2c_set_clientdata(i2c, lp3972);
+ return 0;
+
+err_detect:
+ kfree(lp3972);
+ return ret;
+}
+
+static int __devexit lp3972_i2c_remove(struct i2c_client *i2c)
+{
+ struct lp3972 *lp3972 = i2c_get_clientdata(i2c);
+ int i;
+
+ for (i = 0; i < lp3972->num_regulators; i++)
+ regulator_unregister(lp3972->rdev[i]);
+ kfree(lp3972->rdev);
+ kfree(lp3972);
+
+ return 0;
+}
+
+static const struct i2c_device_id lp3972_i2c_id[] = {
+ { "lp3972", 0 },
+ { }
+};
+MODULE_DEVICE_TABLE(i2c, lp3972_i2c_id);
+
+static struct i2c_driver lp3972_i2c_driver = {
+ .driver = {
+ .name = "lp3972",
+ .owner = THIS_MODULE,
+ },
+ .probe = lp3972_i2c_probe,
+ .remove = __devexit_p(lp3972_i2c_remove),
+ .id_table = lp3972_i2c_id,
+};
+
+static int __init lp3972_module_init(void)
+{
+ return i2c_add_driver(&lp3972_i2c_driver);
+}
+subsys_initcall(lp3972_module_init);
+
+static void __exit lp3972_module_exit(void)
+{
+ i2c_del_driver(&lp3972_i2c_driver);
+}
+module_exit(lp3972_module_exit);
+
+MODULE_LICENSE("GPL");
+MODULE_AUTHOR("Axel Lin <axel.lin@gmail.com>");
+MODULE_DESCRIPTION("LP3972 PMIC driver");
diff --git a/drivers/regulator/max8952.c b/drivers/regulator/max8952.c
new file mode 100644
index 0000000..0d5dda4
--- /dev/null
+++ b/drivers/regulator/max8952.c
@@ -0,0 +1,366 @@
+/*
+ * max8952.c - Voltage and current regulation for the Maxim 8952
+ *
+ * Copyright (C) 2010 Samsung Electronics
+ * MyungJoo Ham <myungjoo.ham@samsung.com>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA
+ */
+
+#include <linux/module.h>
+#include <linux/init.h>
+#include <linux/i2c.h>
+#include <linux/err.h>
+#include <linux/platform_device.h>
+#include <linux/regulator/driver.h>
+#include <linux/regulator/max8952.h>
+#include <linux/mutex.h>
+#include <linux/gpio.h>
+#include <linux/io.h>
+#include <linux/slab.h>
+
+/* Registers */
+enum {
+ MAX8952_REG_MODE0,
+ MAX8952_REG_MODE1,
+ MAX8952_REG_MODE2,
+ MAX8952_REG_MODE3,
+ MAX8952_REG_CONTROL,
+ MAX8952_REG_SYNC,
+ MAX8952_REG_RAMP,
+ MAX8952_REG_CHIP_ID1,
+ MAX8952_REG_CHIP_ID2,
+};
+
+struct max8952_data {
+ struct i2c_client *client;
+ struct device *dev;
+ struct mutex mutex;
+ struct max8952_platform_data *pdata;
+ struct regulator_dev *rdev;
+
+ bool vid0;
+ bool vid1;
+ bool en;
+};
+
+static int max8952_read_reg(struct max8952_data *max8952, u8 reg)
+{
+ int ret = i2c_smbus_read_byte_data(max8952->client, reg);
+ if (ret > 0)
+ ret &= 0xff;
+
+ return ret;
+}
+
+static int max8952_write_reg(struct max8952_data *max8952,
+ u8 reg, u8 value)
+{
+ return i2c_smbus_write_byte_data(max8952->client, reg, value);
+}
+
+static int max8952_voltage(struct max8952_data *max8952, u8 mode)
+{
+ return (max8952->pdata->dvs_mode[mode] * 10 + 770) * 1000;
+}
+
+static int max8952_list_voltage(struct regulator_dev *rdev,
+ unsigned int selector)
+{
+ struct max8952_data *max8952 = rdev_get_drvdata(rdev);
+
+ if (rdev_get_id(rdev) != 0)
+ return -EINVAL;
+
+ return max8952_voltage(max8952, selector);
+}
+
+static int max8952_is_enabled(struct regulator_dev *rdev)
+{
+ struct max8952_data *max8952 = rdev_get_drvdata(rdev);
+ return max8952->en;
+}
+
+static int max8952_enable(struct regulator_dev *rdev)
+{
+ struct max8952_data *max8952 = rdev_get_drvdata(rdev);
+
+ /* If not valid, assume "ALWAYS_HIGH" */
+ if (gpio_is_valid(max8952->pdata->gpio_en))
+ gpio_set_value(max8952->pdata->gpio_en, 1);
+
+ max8952->en = true;
+ return 0;
+}
+
+static int max8952_disable(struct regulator_dev *rdev)
+{
+ struct max8952_data *max8952 = rdev_get_drvdata(rdev);
+
+ /* If not valid, assume "ALWAYS_HIGH" -> not permitted */
+ if (gpio_is_valid(max8952->pdata->gpio_en))
+ gpio_set_value(max8952->pdata->gpio_en, 0);
+ else
+ return -EPERM;
+
+ max8952->en = false;
+ return 0;
+}
+
+static int max8952_get_voltage(struct regulator_dev *rdev)
+{
+ struct max8952_data *max8952 = rdev_get_drvdata(rdev);
+ u8 vid = 0;
+
+ if (max8952->vid0)
+ vid += 1;
+ if (max8952->vid1)
+ vid += 2;
+
+ return max8952_voltage(max8952, vid);
+}
+
+static int max8952_set_voltage(struct regulator_dev *rdev,
+ int min_uV, int max_uV)
+{
+ struct max8952_data *max8952 = rdev_get_drvdata(rdev);
+ s8 vid = -1, i;
+
+ if (!gpio_is_valid(max8952->pdata->gpio_vid0) ||
+ !gpio_is_valid(max8952->pdata->gpio_vid0)) {
+ /* DVS not supported */
+ return -EPERM;
+ }
+
+ for (i = 0; i < MAX8952_NUM_DVS_MODE; i++) {
+ int volt = max8952_voltage(max8952, i);
+
+ /* Set the voltage as low as possible within the range */
+ if (volt <= max_uV && volt >= min_uV)
+ if (vid == -1 || max8952_voltage(max8952, vid) > volt)
+ vid = i;
+ }
+
+ if (vid >= 0 && vid < MAX8952_NUM_DVS_MODE) {
+ max8952->vid0 = (vid % 2 == 1);
+ max8952->vid1 = (((vid >> 1) % 2) == 1);
+ gpio_set_value(max8952->pdata->gpio_vid0, max8952->vid0);
+ gpio_set_value(max8952->pdata->gpio_vid1, max8952->vid1);
+ } else
+ return -EINVAL;
+
+ return 0;
+}
+
+static struct regulator_ops max8952_ops = {
+ .list_voltage = max8952_list_voltage,
+ .is_enabled = max8952_is_enabled,
+ .enable = max8952_enable,
+ .disable = max8952_disable,
+ .get_voltage = max8952_get_voltage,
+ .set_voltage = max8952_set_voltage,
+ .set_suspend_disable = max8952_disable,
+};
+
+static struct regulator_desc regulator = {
+ .name = "MAX8952_VOUT",
+ .id = 0,
+ .n_voltages = MAX8952_NUM_DVS_MODE,
+ .ops = &max8952_ops,
+ .type = REGULATOR_VOLTAGE,
+ .owner = THIS_MODULE,
+};
+
+static int __devinit max8952_pmic_probe(struct i2c_client *client,
+ const struct i2c_device_id *i2c_id)
+{
+ struct i2c_adapter *adapter = to_i2c_adapter(client->dev.parent);
+ struct max8952_platform_data *pdata = client->dev.platform_data;
+ struct max8952_data *max8952;
+
+ int ret = 0, err = 0;
+
+ if (!pdata) {
+ dev_err(&client->dev, "Require the platform data\n");
+ return -EINVAL;
+ }
+
+ if (!i2c_check_functionality(adapter, I2C_FUNC_SMBUS_BYTE))
+ return -EIO;
+
+ max8952 = kzalloc(sizeof(struct max8952_data), GFP_KERNEL);
+ if (!max8952)
+ return -ENOMEM;
+
+ max8952->client = client;
+ max8952->dev = &client->dev;
+ max8952->pdata = pdata;
+ mutex_init(&max8952->mutex);
+
+ max8952->rdev = regulator_register(®ulator, max8952->dev,
+ &pdata->reg_data, max8952);
+
+ if (IS_ERR(max8952->rdev)) {
+ ret = PTR_ERR(max8952->rdev);
+ dev_err(max8952->dev, "regulator init failed (%d)\n", ret);
+ goto err_reg;
+ }
+
+ max8952->en = !!(pdata->reg_data.constraints.boot_on);
+ max8952->vid0 = (pdata->default_mode % 2) == 1;
+ max8952->vid1 = ((pdata->default_mode >> 1) % 2) == 1;
+
+ if (gpio_is_valid(pdata->gpio_en)) {
+ if (!gpio_request(pdata->gpio_en, "MAX8952 EN"))
+ gpio_direction_output(pdata->gpio_en, max8952->en);
+ else
+ err = 1;
+ } else
+ err = 2;
+
+ if (err) {
+ dev_info(max8952->dev, "EN gpio invalid: assume that EN"
+ "is always High\n");
+ max8952->en = 1;
+ pdata->gpio_en = -1; /* Mark invalid */
+ }
+
+ err = 0;
+
+ if (gpio_is_valid(pdata->gpio_vid0) &&
+ gpio_is_valid(pdata->gpio_vid1)) {
+ if (!gpio_request(pdata->gpio_vid0, "MAX8952 VID0"))
+ gpio_direction_output(pdata->gpio_vid0,
+ (pdata->default_mode) % 2);
+ else
+ err = 1;
+
+ if (!gpio_request(pdata->gpio_vid1, "MAX8952 VID1"))
+ gpio_direction_output(pdata->gpio_vid1,
+ (pdata->default_mode >> 1) % 2);
+ else {
+ if (!err)
+ gpio_free(pdata->gpio_vid0);
+ err = 2;
+ }
+
+ } else
+ err = 3;
+
+ if (err) {
+ dev_warn(max8952->dev, "VID0/1 gpio invalid: "
+ "DVS not avilable.\n");
+ max8952->vid0 = 0;
+ max8952->vid1 = 0;
+ /* Mark invalid */
+ pdata->gpio_vid0 = -1;
+ pdata->gpio_vid1 = -1;
+
+ /* Disable Pulldown of EN only */
+ max8952_write_reg(max8952, MAX8952_REG_CONTROL, 0x60);
+
+ dev_err(max8952->dev, "DVS modes disabled because VID0 and VID1"
+ " do not have proper controls.\n");
+ } else {
+ /*
+ * Disable Pulldown on EN, VID0, VID1 to reduce
+ * leakage current of MAX8952 assuming that MAX8952
+ * is turned on (EN==1). Note that without having VID0/1
+ * properly connected, turning pulldown off can be
+ * problematic. Thus, turn this off only when they are
+ * controllable by GPIO.
+ */
+ max8952_write_reg(max8952, MAX8952_REG_CONTROL, 0x0);
+ }
+
+ max8952_write_reg(max8952, MAX8952_REG_MODE0,
+ (max8952_read_reg(max8952,
+ MAX8952_REG_MODE0) & 0xC0) |
+ (pdata->dvs_mode[0] & 0x3F));
+ max8952_write_reg(max8952, MAX8952_REG_MODE1,
+ (max8952_read_reg(max8952,
+ MAX8952_REG_MODE1) & 0xC0) |
+ (pdata->dvs_mode[1] & 0x3F));
+ max8952_write_reg(max8952, MAX8952_REG_MODE2,
+ (max8952_read_reg(max8952,
+ MAX8952_REG_MODE2) & 0xC0) |
+ (pdata->dvs_mode[2] & 0x3F));
+ max8952_write_reg(max8952, MAX8952_REG_MODE3,
+ (max8952_read_reg(max8952,
+ MAX8952_REG_MODE3) & 0xC0) |
+ (pdata->dvs_mode[3] & 0x3F));
+
+ max8952_write_reg(max8952, MAX8952_REG_SYNC,
+ (max8952_read_reg(max8952, MAX8952_REG_SYNC) & 0x3F) |
+ ((pdata->sync_freq & 0x3) << 6));
+ max8952_write_reg(max8952, MAX8952_REG_RAMP,
+ (max8952_read_reg(max8952, MAX8952_REG_RAMP) & 0x1F) |
+ ((pdata->ramp_speed & 0x7) << 5));
+
+ i2c_set_clientdata(client, max8952);
+
+ return 0;
+
+err_reg:
+ kfree(max8952);
+ return ret;
+}
+
+static int __devexit max8952_pmic_remove(struct i2c_client *client)
+{
+ struct max8952_data *max8952 = i2c_get_clientdata(client);
+ struct max8952_platform_data *pdata = max8952->pdata;
+ struct regulator_dev *rdev = max8952->rdev;
+
+ regulator_unregister(rdev);
+
+ gpio_free(pdata->gpio_vid0);
+ gpio_free(pdata->gpio_vid1);
+ gpio_free(pdata->gpio_en);
+
+ kfree(max8952);
+ return 0;
+}
+
+static const struct i2c_device_id max8952_ids[] = {
+ { "max8952", 0 },
+ { },
+};
+MODULE_DEVICE_TABLE(i2c, max8952_ids);
+
+static struct i2c_driver max8952_pmic_driver = {
+ .probe = max8952_pmic_probe,
+ .remove = __devexit_p(max8952_pmic_remove),
+ .driver = {
+ .name = "max8952",
+ },
+ .id_table = max8952_ids,
+};
+
+static int __init max8952_pmic_init(void)
+{
+ return i2c_add_driver(&max8952_pmic_driver);
+}
+subsys_initcall(max8952_pmic_init);
+
+static void __exit max8952_pmic_exit(void)
+{
+ i2c_del_driver(&max8952_pmic_driver);
+}
+module_exit(max8952_pmic_exit);
+
+MODULE_DESCRIPTION("MAXIM 8952 voltage regulator driver");
+MODULE_AUTHOR("MyungJoo Ham <myungjoo.ham@samsung.com>");
+MODULE_LICENSE("GPL");
diff --git a/fs/ext4/inode.c b/fs/ext4/inode.c
index 2d6c6c8..1916164 100644
--- a/fs/ext4/inode.c
+++ b/fs/ext4/inode.c
@@ -2718,7 +2718,7 @@
* try to create them using __block_write_begin. If this
* fails, redirty the page and move on.
*/
- if (!page_buffers(page)) {
+ if (!page_has_buffers(page)) {
if (__block_write_begin(page, 0, len,
noalloc_get_block_write)) {
redirty_page:
@@ -2732,12 +2732,10 @@
if (walk_page_buffers(NULL, page_bufs, 0, len, NULL,
ext4_bh_delay_or_unwritten)) {
/*
- * We don't want to do block allocation So redirty the
- * page and return We may reach here when we do a
- * journal commit via
- * journal_submit_inode_data_buffers. If we don't
- * have mapping block we just ignore them. We can also
- * reach here via shrink_page_list
+ * We don't want to do block allocation, so redirty
+ * the page and return. We may reach here when we do
+ * a journal commit via journal_submit_inode_data_buffers.
+ * We can also reach here via shrink_page_list
*/
goto redirty_page;
}
diff --git a/fs/nfs/direct.c b/fs/nfs/direct.c
index 064a809..84d3c8b 100644
--- a/fs/nfs/direct.c
+++ b/fs/nfs/direct.c
@@ -873,7 +873,7 @@
dreq->inode = inode;
dreq->ctx = get_nfs_open_context(nfs_file_open_context(iocb->ki_filp));
dreq->l_ctx = nfs_get_lock_context(dreq->ctx);
- if (dreq->l_ctx != NULL)
+ if (dreq->l_ctx == NULL)
goto out_release;
if (!is_sync_kiocb(iocb))
dreq->iocb = iocb;
diff --git a/fs/nfs/idmap.c b/fs/nfs/idmap.c
index dec47ed..4e2d9b6 100644
--- a/fs/nfs/idmap.c
+++ b/fs/nfs/idmap.c
@@ -123,7 +123,7 @@
size_t desclen = typelen + namelen + 2;
*desc = kmalloc(desclen, GFP_KERNEL);
- if (!desc)
+ if (!*desc)
return -ENOMEM;
cp = *desc;
diff --git a/fs/nfs/nfs4proc.c b/fs/nfs/nfs4proc.c
index 32c8758..0f24cdf 100644
--- a/fs/nfs/nfs4proc.c
+++ b/fs/nfs/nfs4proc.c
@@ -429,7 +429,7 @@
* returned NFS4ERR_DELAY as per Section 2.10.6.2
* of RFC5661.
*/
- dprintk("%s: slot=%ld seq=%d: Operation in progress\n",
+ dprintk("%s: slot=%td seq=%d: Operation in progress\n",
__func__,
res->sr_slot - res->sr_session->fc_slot_table.slots,
res->sr_slot->seq_nr);
@@ -573,7 +573,7 @@
goto out;
}
- dprintk("--> %s clp %p session %p sr_slot %ld\n",
+ dprintk("--> %s clp %p session %p sr_slot %td\n",
__func__, session->clp, session, res->sr_slot ?
res->sr_slot - session->fc_slot_table.slots : -1);
diff --git a/fs/nfs/pagelist.c b/fs/nfs/pagelist.c
index 9194902..137b549 100644
--- a/fs/nfs/pagelist.c
+++ b/fs/nfs/pagelist.c
@@ -65,6 +65,13 @@
if (req == NULL)
return ERR_PTR(-ENOMEM);
+ /* get lock context early so we can deal with alloc failures */
+ req->wb_lock_context = nfs_get_lock_context(ctx);
+ if (req->wb_lock_context == NULL) {
+ nfs_page_free(req);
+ return ERR_PTR(-ENOMEM);
+ }
+
/* Initialize the request struct. Initially, we assume a
* long write-back delay. This will be adjusted in
* update_nfs_request below if the region is not locked. */
@@ -79,7 +86,6 @@
req->wb_pgbase = offset;
req->wb_bytes = count;
req->wb_context = get_nfs_open_context(ctx);
- req->wb_lock_context = nfs_get_lock_context(ctx);
kref_init(&req->wb_kref);
return req;
}
diff --git a/include/asm-generic/vmlinux.lds.h b/include/asm-generic/vmlinux.lds.h
index 2c0fc10..bd69d79 100644
--- a/include/asm-generic/vmlinux.lds.h
+++ b/include/asm-generic/vmlinux.lds.h
@@ -640,7 +640,8 @@
. = ALIGN(4); \
VMLINUX_SYMBOL(__initramfs_start) = .; \
*(.init.ramfs) \
- VMLINUX_SYMBOL(__initramfs_end) = .;
+ . = ALIGN(8); \
+ *(.init.ramfs.info)
#else
#define INIT_RAM_FS
#endif
diff --git a/include/linux/regulator/lp3972.h b/include/linux/regulator/lp3972.h
new file mode 100644
index 0000000..9bb7389
--- /dev/null
+++ b/include/linux/regulator/lp3972.h
@@ -0,0 +1,48 @@
+/*
+ * National Semiconductors LP3972 PMIC chip client interface
+ *
+ * Based on lp3971.h
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA.
+ */
+
+#ifndef __LINUX_REGULATOR_LP3972_H
+#define __LINUX_REGULATOR_LP3972_H
+
+#include <linux/regulator/machine.h>
+
+#define LP3972_LDO1 0
+#define LP3972_LDO2 1
+#define LP3972_LDO3 2
+#define LP3972_LDO4 3
+#define LP3972_LDO5 4
+
+#define LP3972_DCDC1 5
+#define LP3972_DCDC2 6
+#define LP3972_DCDC3 7
+
+#define LP3972_NUM_REGULATORS 8
+
+struct lp3972_regulator_subdev {
+ int id;
+ struct regulator_init_data *initdata;
+};
+
+struct lp3972_platform_data {
+ int num_regulators;
+ struct lp3972_regulator_subdev *regulators;
+};
+
+#endif
diff --git a/include/linux/regulator/machine.h b/include/linux/regulator/machine.h
index e298028..761c745 100644
--- a/include/linux/regulator/machine.h
+++ b/include/linux/regulator/machine.h
@@ -189,10 +189,15 @@
#ifdef CONFIG_REGULATOR
void regulator_has_full_constraints(void);
+void regulator_use_dummy_regulator(void);
#else
static inline void regulator_has_full_constraints(void)
{
}
+
+static inline void regulator_use_dummy_regulator(void)
+{
+}
#endif
#endif
diff --git a/include/linux/regulator/max8952.h b/include/linux/regulator/max8952.h
new file mode 100644
index 0000000..45e4285
--- /dev/null
+++ b/include/linux/regulator/max8952.h
@@ -0,0 +1,135 @@
+/*
+ * max8952.h - Voltage regulation for the Maxim 8952
+ *
+ * Copyright (C) 2010 Samsung Electrnoics
+ * MyungJoo Ham <myungjoo.ham@samsung.com>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA
+ */
+
+#ifndef REGULATOR_MAX8952
+#define REGULATOR_MAX8952
+
+#include <linux/regulator/machine.h>
+
+enum {
+ MAX8952_DVS_MODE0,
+ MAX8952_DVS_MODE1,
+ MAX8952_DVS_MODE2,
+ MAX8952_DVS_MODE3,
+};
+
+enum {
+ MAX8952_DVS_770mV = 0,
+ MAX8952_DVS_780mV,
+ MAX8952_DVS_790mV,
+ MAX8952_DVS_800mV,
+ MAX8952_DVS_810mV,
+ MAX8952_DVS_820mV,
+ MAX8952_DVS_830mV,
+ MAX8952_DVS_840mV,
+ MAX8952_DVS_850mV,
+ MAX8952_DVS_860mV,
+ MAX8952_DVS_870mV,
+ MAX8952_DVS_880mV,
+ MAX8952_DVS_890mV,
+ MAX8952_DVS_900mV,
+ MAX8952_DVS_910mV,
+ MAX8952_DVS_920mV,
+ MAX8952_DVS_930mV,
+ MAX8952_DVS_940mV,
+ MAX8952_DVS_950mV,
+ MAX8952_DVS_960mV,
+ MAX8952_DVS_970mV,
+ MAX8952_DVS_980mV,
+ MAX8952_DVS_990mV,
+ MAX8952_DVS_1000mV,
+ MAX8952_DVS_1010mV,
+ MAX8952_DVS_1020mV,
+ MAX8952_DVS_1030mV,
+ MAX8952_DVS_1040mV,
+ MAX8952_DVS_1050mV,
+ MAX8952_DVS_1060mV,
+ MAX8952_DVS_1070mV,
+ MAX8952_DVS_1080mV,
+ MAX8952_DVS_1090mV,
+ MAX8952_DVS_1100mV,
+ MAX8952_DVS_1110mV,
+ MAX8952_DVS_1120mV,
+ MAX8952_DVS_1130mV,
+ MAX8952_DVS_1140mV,
+ MAX8952_DVS_1150mV,
+ MAX8952_DVS_1160mV,
+ MAX8952_DVS_1170mV,
+ MAX8952_DVS_1180mV,
+ MAX8952_DVS_1190mV,
+ MAX8952_DVS_1200mV,
+ MAX8952_DVS_1210mV,
+ MAX8952_DVS_1220mV,
+ MAX8952_DVS_1230mV,
+ MAX8952_DVS_1240mV,
+ MAX8952_DVS_1250mV,
+ MAX8952_DVS_1260mV,
+ MAX8952_DVS_1270mV,
+ MAX8952_DVS_1280mV,
+ MAX8952_DVS_1290mV,
+ MAX8952_DVS_1300mV,
+ MAX8952_DVS_1310mV,
+ MAX8952_DVS_1320mV,
+ MAX8952_DVS_1330mV,
+ MAX8952_DVS_1340mV,
+ MAX8952_DVS_1350mV,
+ MAX8952_DVS_1360mV,
+ MAX8952_DVS_1370mV,
+ MAX8952_DVS_1380mV,
+ MAX8952_DVS_1390mV,
+ MAX8952_DVS_1400mV,
+};
+
+enum {
+ MAX8952_SYNC_FREQ_26MHZ, /* Default */
+ MAX8952_SYNC_FREQ_13MHZ,
+ MAX8952_SYNC_FREQ_19_2MHZ,
+};
+
+enum {
+ MAX8952_RAMP_32mV_us = 0, /* Default */
+ MAX8952_RAMP_16mV_us,
+ MAX8952_RAMP_8mV_us,
+ MAX8952_RAMP_4mV_us,
+ MAX8952_RAMP_2mV_us,
+ MAX8952_RAMP_1mV_us,
+ MAX8952_RAMP_0_5mV_us,
+ MAX8952_RAMP_0_25mV_us,
+};
+
+#define MAX8952_NUM_DVS_MODE 4
+
+struct max8952_platform_data {
+ int gpio_vid0;
+ int gpio_vid1;
+ int gpio_en;
+
+ u8 default_mode;
+ u8 dvs_mode[MAX8952_NUM_DVS_MODE]; /* MAX8952_DVS_MODEx_XXXXmV */
+
+ u8 sync_freq;
+ u8 ramp_speed;
+
+ struct regulator_init_data reg_data;
+};
+
+
+#endif /* REGULATOR_MAX8952 */
diff --git a/init/initramfs.c b/init/initramfs.c
index d9c6e78..2531811 100644
--- a/init/initramfs.c
+++ b/init/initramfs.c
@@ -483,7 +483,8 @@
}
__setup("retain_initrd", retain_initrd_param);
-extern char __initramfs_start[], __initramfs_end[];
+extern char __initramfs_start[];
+extern unsigned long __initramfs_size;
#include <linux/initrd.h>
#include <linux/kexec.h>
@@ -570,8 +571,7 @@
static int __init populate_rootfs(void)
{
- char *err = unpack_to_rootfs(__initramfs_start,
- __initramfs_end - __initramfs_start);
+ char *err = unpack_to_rootfs(__initramfs_start, __initramfs_size);
if (err)
panic(err); /* Failed to decompress INTERNAL initramfs */
if (initrd_start) {
@@ -585,8 +585,7 @@
return 0;
} else {
clean_rootfs();
- unpack_to_rootfs(__initramfs_start,
- __initramfs_end - __initramfs_start);
+ unpack_to_rootfs(__initramfs_start, __initramfs_size);
}
printk(KERN_INFO "rootfs image is not initramfs (%s)"
"; looks like an initrd\n", err);
diff --git a/scripts/Makefile.clean b/scripts/Makefile.clean
index 6f89fbb..686cb0d 100644
--- a/scripts/Makefile.clean
+++ b/scripts/Makefile.clean
@@ -45,6 +45,8 @@
$(host-progs) \
$(hostprogs-y) $(hostprogs-m) $(hostprogs-)
+__clean-files := $(filter-out $(no-clean-files), $(__clean-files))
+
# as clean-files is given relative to the current directory, this adds
# a $(obj) prefix, except for absolute paths
diff --git a/scripts/Makefile.lib b/scripts/Makefile.lib
index 7bfcf1a..4c72c11 100644
--- a/scripts/Makefile.lib
+++ b/scripts/Makefile.lib
@@ -120,7 +120,9 @@
endif
ifdef CONFIG_SYMBOL_PREFIX
-_cpp_flags += -DSYMBOL_PREFIX=$(patsubst "%",%,$(CONFIG_SYMBOL_PREFIX))
+_sym_flags = -DSYMBOL_PREFIX=$(patsubst "%",%,$(CONFIG_SYMBOL_PREFIX))
+_cpp_flags += $(_sym_flags)
+_a_flags += $(_sym_flags)
endif
diff --git a/scripts/kallsyms.c b/scripts/kallsyms.c
index e3902fb..60dd3eb 100644
--- a/scripts/kallsyms.c
+++ b/scripts/kallsyms.c
@@ -107,12 +107,8 @@
rc = fscanf(in, "%llx %c %499s\n", &s->addr, &stype, str);
if (rc != 3) {
- if (rc != EOF) {
- /* skip line. sym is used as dummy to
- * shut of "warn_unused_result" warning.
- */
- sym = fgets(str, 500, in);
- }
+ if (rc != EOF && fgets(str, 500, in) == NULL)
+ fprintf(stderr, "Read error or end of file.\n");
return -1;
}
diff --git a/scripts/mod/modpost.c b/scripts/mod/modpost.c
index 1ec7158..33122ca 100644
--- a/scripts/mod/modpost.c
+++ b/scripts/mod/modpost.c
@@ -1208,6 +1208,9 @@
* .cpuinit.data => __cpudata
* .memexitconst => __memconst
* etc.
+ *
+ * The memory of returned value has been allocated on a heap. The user of this
+ * method should free it after usage.
*/
static char *sec2annotation(const char *s)
{
@@ -1230,7 +1233,7 @@
strcat(p, "data ");
else
strcat(p, " ");
- return r; /* we leak her but we do not care */
+ return r;
} else {
return strdup("");
}
diff --git a/scripts/setlocalversion b/scripts/setlocalversion
index 057b6b3..ef8729f 100755
--- a/scripts/setlocalversion
+++ b/scripts/setlocalversion
@@ -160,8 +160,10 @@
# full scm version string
res="$res$(scm_version)"
else
- # apped a plus sign if the repository is not in a clean tagged
- # state and LOCALVERSION= is not specified
+ # append a plus sign if the repository is not in a clean
+ # annotated or signed tagged state (as git describe only
+ # looks at signed or annotated tags - git tag -a/-s) and
+ # LOCALVERSION= is not specified
if test "${LOCALVERSION+set}" != "set"; then
scm=$(scm_version --short)
res="$res${scm:++}"
diff --git a/usr/Makefile b/usr/Makefile
index 6b4b6da..6faa444 100644
--- a/usr/Makefile
+++ b/usr/Makefile
@@ -18,13 +18,15 @@
# Lzo
suffix_$(CONFIG_INITRAMFS_COMPRESSION_LZO) = .lzo
+AFLAGS_initramfs_data.o += -DINITRAMFS_IMAGE="usr/initramfs_data.cpio$(suffix_y)"
+
# Generate builtin.o based on initramfs_data.o
-obj-$(CONFIG_BLK_DEV_INITRD) := initramfs_data$(suffix_y).o
+obj-$(CONFIG_BLK_DEV_INITRD) := initramfs_data.o
# initramfs_data.o contains the compressed initramfs_data.cpio image.
# The image is included using .incbin, a dependency which is not
# tracked automatically.
-$(obj)/initramfs_data$(suffix_y).o: $(obj)/initramfs_data.cpio$(suffix_y) FORCE
+$(obj)/initramfs_data.o: $(obj)/initramfs_data.cpio$(suffix_y) FORCE
#####
# Generate the initramfs cpio archive
diff --git a/usr/initramfs_data.S b/usr/initramfs_data.S
index 7c6973d..b9efed5 100644
--- a/usr/initramfs_data.S
+++ b/usr/initramfs_data.S
@@ -11,11 +11,7 @@
-T initramfs_data.scr initramfs_data.cpio.gz -o initramfs_data.o
ld -m elf_i386 -r -o built-in.o initramfs_data.o
- initramfs_data.scr looks like this:
-SECTIONS
-{
- .init.ramfs : { *(.data) }
-}
+ For including the .init.ramfs sections, see include/asm-generic/vmlinux.lds.
The above example is for i386 - the parameters vary from architectures.
Eventually look up LDFLAGS_BLOB in an older version of the
@@ -25,6 +21,17 @@
in the ELF header, as required by certain architectures.
*/
-.section .init.ramfs,"a"
-.incbin "usr/initramfs_data.cpio"
+#include <linux/stringify.h>
+.section .init.ramfs,"a"
+__irf_start:
+.incbin __stringify(INITRAMFS_IMAGE)
+__irf_end:
+.section .init.ramfs.info,"a"
+.globl __initramfs_size
+__initramfs_size:
+#ifdef CONFIG_32BIT
+ .long __irf_end - __irf_start
+#else
+ .quad __irf_end - __irf_start
+#endif
diff --git a/usr/initramfs_data.bz2.S b/usr/initramfs_data.bz2.S
deleted file mode 100644
index bc54d09..0000000
--- a/usr/initramfs_data.bz2.S
+++ /dev/null
@@ -1,29 +0,0 @@
-/*
- initramfs_data includes the compressed binary that is the
- filesystem used for early user space.
- Note: Older versions of "as" (prior to binutils 2.11.90.0.23
- released on 2001-07-14) dit not support .incbin.
- If you are forced to use older binutils than that then the
- following trick can be applied to create the resulting binary:
-
-
- ld -m elf_i386 --format binary --oformat elf32-i386 -r \
- -T initramfs_data.scr initramfs_data.cpio.gz -o initramfs_data.o
- ld -m elf_i386 -r -o built-in.o initramfs_data.o
-
- initramfs_data.scr looks like this:
-SECTIONS
-{
- .init.ramfs : { *(.data) }
-}
-
- The above example is for i386 - the parameters vary from architectures.
- Eventually look up LDFLAGS_BLOB in an older version of the
- arch/$(ARCH)/Makefile to see the flags used before .incbin was introduced.
-
- Using .incbin has the advantage over ld that the correct flags are set
- in the ELF header, as required by certain architectures.
-*/
-
-.section .init.ramfs,"a"
-.incbin "usr/initramfs_data.cpio.bz2"
diff --git a/usr/initramfs_data.gz.S b/usr/initramfs_data.gz.S
deleted file mode 100644
index 890c8dd..0000000
--- a/usr/initramfs_data.gz.S
+++ /dev/null
@@ -1,29 +0,0 @@
-/*
- initramfs_data includes the compressed binary that is the
- filesystem used for early user space.
- Note: Older versions of "as" (prior to binutils 2.11.90.0.23
- released on 2001-07-14) dit not support .incbin.
- If you are forced to use older binutils than that then the
- following trick can be applied to create the resulting binary:
-
-
- ld -m elf_i386 --format binary --oformat elf32-i386 -r \
- -T initramfs_data.scr initramfs_data.cpio.gz -o initramfs_data.o
- ld -m elf_i386 -r -o built-in.o initramfs_data.o
-
- initramfs_data.scr looks like this:
-SECTIONS
-{
- .init.ramfs : { *(.data) }
-}
-
- The above example is for i386 - the parameters vary from architectures.
- Eventually look up LDFLAGS_BLOB in an older version of the
- arch/$(ARCH)/Makefile to see the flags used before .incbin was introduced.
-
- Using .incbin has the advantage over ld that the correct flags are set
- in the ELF header, as required by certain architectures.
-*/
-
-.section .init.ramfs,"a"
-.incbin "usr/initramfs_data.cpio.gz"
diff --git a/usr/initramfs_data.lzma.S b/usr/initramfs_data.lzma.S
deleted file mode 100644
index e11469e..0000000
--- a/usr/initramfs_data.lzma.S
+++ /dev/null
@@ -1,29 +0,0 @@
-/*
- initramfs_data includes the compressed binary that is the
- filesystem used for early user space.
- Note: Older versions of "as" (prior to binutils 2.11.90.0.23
- released on 2001-07-14) dit not support .incbin.
- If you are forced to use older binutils than that then the
- following trick can be applied to create the resulting binary:
-
-
- ld -m elf_i386 --format binary --oformat elf32-i386 -r \
- -T initramfs_data.scr initramfs_data.cpio.gz -o initramfs_data.o
- ld -m elf_i386 -r -o built-in.o initramfs_data.o
-
- initramfs_data.scr looks like this:
-SECTIONS
-{
- .init.ramfs : { *(.data) }
-}
-
- The above example is for i386 - the parameters vary from architectures.
- Eventually look up LDFLAGS_BLOB in an older version of the
- arch/$(ARCH)/Makefile to see the flags used before .incbin was introduced.
-
- Using .incbin has the advantage over ld that the correct flags are set
- in the ELF header, as required by certain architectures.
-*/
-
-.section .init.ramfs,"a"
-.incbin "usr/initramfs_data.cpio.lzma"
diff --git a/usr/initramfs_data.lzo.S b/usr/initramfs_data.lzo.S
deleted file mode 100644
index 5921190..0000000
--- a/usr/initramfs_data.lzo.S
+++ /dev/null
@@ -1,29 +0,0 @@
-/*
- initramfs_data includes the compressed binary that is the
- filesystem used for early user space.
- Note: Older versions of "as" (prior to binutils 2.11.90.0.23
- released on 2001-07-14) dit not support .incbin.
- If you are forced to use older binutils than that then the
- following trick can be applied to create the resulting binary:
-
-
- ld -m elf_i386 --format binary --oformat elf32-i386 -r \
- -T initramfs_data.scr initramfs_data.cpio.gz -o initramfs_data.o
- ld -m elf_i386 -r -o built-in.o initramfs_data.o
-
- initramfs_data.scr looks like this:
-SECTIONS
-{
- .init.ramfs : { *(.data) }
-}
-
- The above example is for i386 - the parameters vary from architectures.
- Eventually look up LDFLAGS_BLOB in an older version of the
- arch/$(ARCH)/Makefile to see the flags used before .incbin was introduced.
-
- Using .incbin has the advantage over ld that the correct flags are set
- in the ELF header, as required by certain architectures.
-*/
-
-.section .init.ramfs,"a"
-.incbin "usr/initramfs_data.cpio.lzo"