ARM: OMAP4: clock: round_rate and recalc functions for DPLL_ABE
OMAP4 DPLL_ABE can enable a 4X multipler on top of the normal MN multipler
and divider. This is achieved by setting CM_CLKMODE_DPLL_ABE.DPLL_REGM4XEN
bit in CKGEN module of CM1. From the OMAP4 TRM:
Fdpll = Fref x 2 x (4 x M/(N+1)) in case REGM4XEN bit field is set (only
applicable to DPLL_ABE).
Add new round_rate() and recalc() functions for OMAP4, that check the
setting of REGM4XEN bit and handle this appropriately. The new functions
are a simple wrapper on top of the existing omap2_dpll_round_rate() and
omap2_dpll_get_rate() functions to handle the REGM4XEN bit.
The REGM4XEN bit is only implemented for the ABE DPLL on OMAP4 and so
only dpll_abe_ck uses omap4_dpll_regm4xen_round_rate() and
omap4_dpll_regm4xen_recalc() functions.
Signed-off-by: Mike Turquette <mturquette@ti.com>
Tested-by: Jon Hunter <jon-hunter@ti.com>
Signed-off-by: Jon Hunter <jon-hunter@ti.com>
[paul@pwsan.com: fixed attempt to return a negative from a fn returning
unsigned; pass along errors from omap2_dpll_round_rate();
added documentation; added Jon's S-o-b]
Signed-off-by: Paul Walmsley <paul@pwsan.com>
diff --git a/arch/arm/mach-omap2/dpll44xx.c b/arch/arm/mach-omap2/dpll44xx.c
index 4e4da61..9c6a296 100644
--- a/arch/arm/mach-omap2/dpll44xx.c
+++ b/arch/arm/mach-omap2/dpll44xx.c
@@ -19,6 +19,7 @@
#include <plat/clock.h>
#include "clock.h"
+#include "clock44xx.h"
#include "cm-regbits-44xx.h"
/* Supported only on OMAP4 */
@@ -82,3 +83,71 @@
.deny_idle = omap4_dpllmx_deny_gatectrl,
};
+/**
+ * omap4_dpll_regm4xen_recalc - compute DPLL rate, considering REGM4XEN bit
+ * @clk: struct clk * of the DPLL to compute the rate for
+ *
+ * Compute the output rate for the OMAP4 DPLL represented by @clk.
+ * Takes the REGM4XEN bit into consideration, which is needed for the
+ * OMAP4 ABE DPLL. Returns the DPLL's output rate (before M-dividers)
+ * upon success, or 0 upon error.
+ */
+unsigned long omap4_dpll_regm4xen_recalc(struct clk *clk)
+{
+ u32 v;
+ unsigned long rate;
+ struct dpll_data *dd;
+
+ if (!clk || !clk->dpll_data)
+ return 0;
+
+ dd = clk->dpll_data;
+
+ rate = omap2_get_dpll_rate(clk);
+
+ /* regm4xen adds a multiplier of 4 to DPLL calculations */
+ v = __raw_readl(dd->control_reg);
+ if (v & OMAP4430_DPLL_REGM4XEN_MASK)
+ rate *= OMAP4430_REGM4XEN_MULT;
+
+ return rate;
+}
+
+/**
+ * omap4_dpll_regm4xen_round_rate - round DPLL rate, considering REGM4XEN bit
+ * @clk: struct clk * of the DPLL to round a rate for
+ * @target_rate: the desired rate of the DPLL
+ *
+ * Compute the rate that would be programmed into the DPLL hardware
+ * for @clk if set_rate() were to be provided with the rate
+ * @target_rate. Takes the REGM4XEN bit into consideration, which is
+ * needed for the OMAP4 ABE DPLL. Returns the rounded rate (before
+ * M-dividers) upon success, -EINVAL if @clk is null or not a DPLL, or
+ * ~0 if an error occurred in omap2_dpll_round_rate().
+ */
+long omap4_dpll_regm4xen_round_rate(struct clk *clk, unsigned long target_rate)
+{
+ u32 v;
+ struct dpll_data *dd;
+ long r;
+
+ if (!clk || !clk->dpll_data)
+ return -EINVAL;
+
+ dd = clk->dpll_data;
+
+ /* regm4xen adds a multiplier of 4 to DPLL calculations */
+ v = __raw_readl(dd->control_reg) & OMAP4430_DPLL_REGM4XEN_MASK;
+
+ if (v)
+ target_rate = target_rate / OMAP4430_REGM4XEN_MULT;
+
+ r = omap2_dpll_round_rate(clk, target_rate);
+ if (r == ~0)
+ return r;
+
+ if (v)
+ clk->dpll_data->last_rounded_rate *= OMAP4430_REGM4XEN_MULT;
+
+ return clk->dpll_data->last_rounded_rate;
+}