| # |
| # Multifunction miscellaneous devices |
| # |
| |
| menuconfig MFD_SUPPORT |
| bool "Multifunction device drivers" |
| depends on HAS_IOMEM |
| default y |
| help |
| Configure MFD device drivers. |
| |
| if MFD_SUPPORT |
| |
| config MFD_CORE |
| tristate |
| default n |
| |
| config MFD_88PM860X |
| bool "Support Marvell 88PM8606/88PM8607" |
| depends on I2C=y && GENERIC_HARDIRQS |
| select MFD_CORE |
| help |
| This supports for Marvell 88PM8606/88PM8607 Power Management IC. |
| This includes the I2C driver and the core APIs _only_, you have to |
| select individual components like voltage regulators, RTC and |
| battery-charger under the corresponding menus. |
| |
| config MFD_SM501 |
| tristate "Support for Silicon Motion SM501" |
| ---help--- |
| This is the core driver for the Silicon Motion SM501 multimedia |
| companion chip. This device is a multifunction device which may |
| provide numerous interfaces including USB host controller, USB gadget, |
| asynchronous serial ports, audio functions, and a dual display video |
| interface. The device may be connected by PCI or local bus with |
| varying functions enabled. |
| |
| config MFD_SM501_GPIO |
| bool "Export GPIO via GPIO layer" |
| depends on MFD_SM501 && GPIOLIB |
| ---help--- |
| This option uses the gpio library layer to export the 64 GPIO |
| lines on the SM501. The platform data is used to supply the |
| base number for the first GPIO line to register. |
| |
| config MFD_ASIC3 |
| bool "Support for Compaq ASIC3" |
| depends on GENERIC_HARDIRQS && GPIOLIB && ARM |
| select MFD_CORE |
| ---help--- |
| This driver supports the ASIC3 multifunction chip found on many |
| PDAs (mainly iPAQ and HTC based ones) |
| |
| config MFD_SH_MOBILE_SDHI |
| bool "Support for SuperH Mobile SDHI" |
| depends on SUPERH || ARCH_SHMOBILE |
| select MFD_CORE |
| select TMIO_MMC_DMA |
| ---help--- |
| This driver supports the SDHI hardware block found in many |
| SuperH Mobile SoCs. |
| |
| config MFD_DAVINCI_VOICECODEC |
| tristate |
| select MFD_CORE |
| |
| config MFD_DM355EVM_MSP |
| bool "DaVinci DM355 EVM microcontroller" |
| depends on I2C && MACH_DAVINCI_DM355_EVM |
| help |
| This driver supports the MSP430 microcontroller used on these |
| boards. MSP430 firmware manages resets and power sequencing, |
| inputs from buttons and the IR remote, LEDs, an RTC, and more. |
| |
| config HTC_EGPIO |
| bool "HTC EGPIO support" |
| depends on GENERIC_HARDIRQS && GPIOLIB && ARM |
| help |
| This driver supports the CPLD egpio chip present on |
| several HTC phones. It provides basic support for input |
| pins, output pins, and irqs. |
| |
| config HTC_PASIC3 |
| tristate "HTC PASIC3 LED/DS1WM chip support" |
| select MFD_CORE |
| help |
| This core driver provides register access for the LED/DS1WM |
| chips labeled "AIC2" and "AIC3", found on HTC Blueangel and |
| HTC Magician devices, respectively. Actual functionality is |
| handled by the leds-pasic3 and ds1wm drivers. |
| |
| config HTC_I2CPLD |
| bool "HTC I2C PLD chip support" |
| depends on I2C=y && GPIOLIB |
| help |
| If you say yes here you get support for the supposed CPLD |
| found on omap850 HTC devices like the HTC Wizard and HTC Herald. |
| This device provides input and output GPIOs through an I2C |
| interface to one or more sub-chips. |
| |
| config UCB1400_CORE |
| tristate "Philips UCB1400 Core driver" |
| depends on AC97_BUS |
| depends on GPIOLIB |
| help |
| This enables support for the Philips UCB1400 core functions. |
| The UCB1400 is an AC97 audio codec. |
| |
| To compile this driver as a module, choose M here: the |
| module will be called ucb1400_core. |
| |
| config TPS65010 |
| tristate "TPS6501x Power Management chips" |
| depends on I2C && GPIOLIB |
| default y if MACH_OMAP_H2 || MACH_OMAP_H3 || MACH_OMAP_OSK |
| help |
| If you say yes here you get support for the TPS6501x series of |
| Power Management chips. These include voltage regulators, |
| lithium ion/polymer battery charging, and other features that |
| are often used in portable devices like cell phones and cameras. |
| |
| This driver can also be built as a module. If so, the module |
| will be called tps65010. |
| |
| config TPS6507X |
| tristate "TPS6507x Power Management / Touch Screen chips" |
| select MFD_CORE |
| depends on I2C |
| help |
| If you say yes here you get support for the TPS6507x series of |
| Power Management / Touch Screen chips. These include voltage |
| regulators, lithium ion/polymer battery charging, touch screen |
| and other features that are often used in portable devices. |
| This driver can also be built as a module. If so, the module |
| will be called tps6507x. |
| |
| config MENELAUS |
| bool "Texas Instruments TWL92330/Menelaus PM chip" |
| depends on I2C=y && ARCH_OMAP2 |
| help |
| If you say yes here you get support for the Texas Instruments |
| TWL92330/Menelaus Power Management chip. This include voltage |
| regulators, Dual slot memory card transceivers, real-time clock |
| and other features that are often used in portable devices like |
| cell phones and PDAs. |
| |
| config TWL4030_CORE |
| bool "Texas Instruments TWL4030/TWL5030/TWL6030/TPS659x0 Support" |
| depends on I2C=y && GENERIC_HARDIRQS |
| help |
| Say yes here if you have TWL4030 / TWL6030 family chip on your board. |
| This core driver provides register access and IRQ handling |
| facilities, and registers devices for the various functions |
| so that function-specific drivers can bind to them. |
| |
| These multi-function chips are found on many OMAP2 and OMAP3 |
| boards, providing power management, RTC, GPIO, keypad, a |
| high speed USB OTG transceiver, an audio codec (on most |
| versions) and many other features. |
| |
| config TWL4030_POWER |
| bool "Support power resources on TWL4030 family chips" |
| depends on TWL4030_CORE && ARM |
| help |
| Say yes here if you want to use the power resources on the |
| TWL4030 family chips. Most of these resources are regulators, |
| which have a separate driver; some are control signals, such |
| as clock request handshaking. |
| |
| This driver uses board-specific data to initialize the resources |
| and load scripts controling which resources are switched off/on |
| or reset when a sleep, wakeup or warm reset event occurs. |
| |
| config TWL4030_CODEC |
| bool |
| depends on TWL4030_CORE |
| select MFD_CORE |
| default n |
| |
| config MFD_TC35892 |
| bool "Support Toshiba TC35892" |
| depends on I2C=y && GENERIC_HARDIRQS |
| select MFD_CORE |
| help |
| Support for the Toshiba TC35892 I/O Expander. |
| |
| This driver provides common support for accessing the device, |
| additional drivers must be enabled in order to use the |
| functionality of the device. |
| |
| config MFD_TMIO |
| bool |
| default n |
| |
| config TMIO_MMC_DMA |
| bool |
| select DMA_ENGINE |
| select DMADEVICES |
| |
| config MFD_T7L66XB |
| bool "Support Toshiba T7L66XB" |
| depends on ARM && HAVE_CLK |
| select MFD_CORE |
| select MFD_TMIO |
| help |
| Support for Toshiba Mobile IO Controller T7L66XB |
| |
| config MFD_TC6387XB |
| bool "Support Toshiba TC6387XB" |
| depends on ARM && HAVE_CLK |
| select MFD_CORE |
| select MFD_TMIO |
| help |
| Support for Toshiba Mobile IO Controller TC6387XB |
| |
| config MFD_TC6393XB |
| bool "Support Toshiba TC6393XB" |
| depends on GPIOLIB && ARM |
| select MFD_CORE |
| select MFD_TMIO |
| help |
| Support for Toshiba Mobile IO Controller TC6393XB |
| |
| config PMIC_DA903X |
| bool "Dialog Semiconductor DA9030/DA9034 PMIC Support" |
| depends on I2C=y |
| help |
| Say yes here to support for Dialog Semiconductor DA9030 (a.k.a |
| ARAVA) and DA9034 (a.k.a MICCO), these are Power Management IC |
| usually found on PXA processors-based platforms. This includes |
| the I2C driver and the core APIs _only_, you have to select |
| individual components like LCD backlight, voltage regulators, |
| LEDs and battery-charger under the corresponding menus. |
| |
| config PMIC_ADP5520 |
| bool "Analog Devices ADP5520/01 MFD PMIC Core Support" |
| depends on I2C=y |
| help |
| Say yes here to add support for Analog Devices AD5520 and ADP5501, |
| Multifunction Power Management IC. This includes |
| the I2C driver and the core APIs _only_, you have to select |
| individual components like LCD backlight, LEDs, GPIOs and Kepad |
| under the corresponding menus. |
| |
| config MFD_MAX8925 |
| bool "Maxim Semiconductor MAX8925 PMIC Support" |
| depends on I2C=y && GENERIC_HARDIRQS |
| select MFD_CORE |
| help |
| Say yes here to support for Maxim Semiconductor MAX8925. This is |
| a Power Management IC. This driver provies common support for |
| accessing the device, additional drivers must be enabled in order |
| to use the functionality of the device. |
| |
| config MFD_WM8400 |
| tristate "Support Wolfson Microelectronics WM8400" |
| select MFD_CORE |
| depends on I2C |
| help |
| Support for the Wolfson Microelecronics WM8400 PMIC and audio |
| CODEC. This driver provides common support for accessing |
| the device, additional drivers must be enabled in order to use |
| the functionality of the device. |
| |
| config MFD_WM831X |
| bool "Support Wolfson Microelectronics WM831x/2x PMICs" |
| select MFD_CORE |
| depends on I2C=y && GENERIC_HARDIRQS |
| help |
| Support for the Wolfson Microelecronics WM831x and WM832x PMICs. |
| This driver provides common support for accessing the device, |
| additional drivers must be enabled in order to use the |
| functionality of the device. |
| |
| config MFD_WM8350 |
| bool |
| depends on GENERIC_HARDIRQS |
| |
| config MFD_WM8350_CONFIG_MODE_0 |
| bool |
| depends on MFD_WM8350 |
| |
| config MFD_WM8350_CONFIG_MODE_1 |
| bool |
| depends on MFD_WM8350 |
| |
| config MFD_WM8350_CONFIG_MODE_2 |
| bool |
| depends on MFD_WM8350 |
| |
| config MFD_WM8350_CONFIG_MODE_3 |
| bool |
| depends on MFD_WM8350 |
| |
| config MFD_WM8351_CONFIG_MODE_0 |
| bool |
| depends on MFD_WM8350 |
| |
| config MFD_WM8351_CONFIG_MODE_1 |
| bool |
| depends on MFD_WM8350 |
| |
| config MFD_WM8351_CONFIG_MODE_2 |
| bool |
| depends on MFD_WM8350 |
| |
| config MFD_WM8351_CONFIG_MODE_3 |
| bool |
| depends on MFD_WM8350 |
| |
| config MFD_WM8352_CONFIG_MODE_0 |
| bool |
| depends on MFD_WM8350 |
| |
| config MFD_WM8352_CONFIG_MODE_1 |
| bool |
| depends on MFD_WM8350 |
| |
| config MFD_WM8352_CONFIG_MODE_2 |
| bool |
| depends on MFD_WM8350 |
| |
| config MFD_WM8352_CONFIG_MODE_3 |
| bool |
| depends on MFD_WM8350 |
| |
| config MFD_WM8350_I2C |
| bool "Support Wolfson Microelectronics WM8350 with I2C" |
| select MFD_WM8350 |
| depends on I2C=y && GENERIC_HARDIRQS |
| help |
| The WM8350 is an integrated audio and power management |
| subsystem with watchdog and RTC functionality for embedded |
| systems. This option enables core support for the WM8350 with |
| I2C as the control interface. Additional options must be |
| selected to enable support for the functionality of the chip. |
| |
| config MFD_WM8994 |
| bool "Support Wolfson Microelectronics WM8994" |
| select MFD_CORE |
| depends on I2C=y && GENERIC_HARDIRQS |
| help |
| The WM8994 is a highly integrated hi-fi CODEC designed for |
| smartphone applicatiosn. As well as audio functionality it |
| has on board GPIO and regulator functionality which is |
| supported via the relevant subsystems. This driver provides |
| core support for the WM8994, in order to use the actual |
| functionaltiy of the device other drivers must be enabled. |
| |
| config MFD_PCF50633 |
| tristate "Support for NXP PCF50633" |
| depends on I2C |
| help |
| Say yes here if you have NXP PCF50633 chip on your board. |
| This core driver provides register access and IRQ handling |
| facilities, and registers devices for the various functions |
| so that function-specific drivers can bind to them. |
| |
| config MFD_MC13783 |
| tristate "Support Freescale MC13783" |
| depends on SPI_MASTER |
| select MFD_CORE |
| help |
| Support for the Freescale (Atlas) MC13783 PMIC and audio CODEC. |
| This driver provides common support for accessing the device, |
| additional drivers must be enabled in order to use the |
| functionality of the device. |
| |
| config PCF50633_ADC |
| tristate "Support for NXP PCF50633 ADC" |
| depends on MFD_PCF50633 |
| help |
| Say yes here if you want to include support for ADC in the |
| NXP PCF50633 chip. |
| |
| config PCF50633_GPIO |
| tristate "Support for NXP PCF50633 GPIO" |
| depends on MFD_PCF50633 |
| help |
| Say yes here if you want to include support GPIO for pins on |
| the PCF50633 chip. |
| |
| config ABX500_CORE |
| bool "ST-Ericsson ABX500 Mixed Signal Circuit register functions" |
| default y if ARCH_U300 |
| help |
| Say yes here if you have the ABX500 Mixed Signal IC family |
| chips. This core driver expose register access functions. |
| Functionality specific drivers using these functions can |
| remain unchanged when IC changes. Binding of the functions to |
| actual register access is done by the IC core driver. |
| |
| config AB3100_CORE |
| bool "ST-Ericsson AB3100 Mixed Signal Circuit core functions" |
| depends on I2C=y && ABX500_CORE |
| default y if ARCH_U300 |
| help |
| Select this to enable the AB3100 Mixed Signal IC core |
| functionality. This connects to a AB3100 on the I2C bus |
| and expose a number of symbols needed for dependent devices |
| to read and write registers and subscribe to events from |
| this multi-functional IC. This is needed to use other features |
| of the AB3100 such as battery-backed RTC, charging control, |
| LEDs, vibrator, system power and temperature, power management |
| and ALSA sound. |
| |
| config AB3100_OTP |
| tristate "ST-Ericsson AB3100 OTP functions" |
| depends on AB3100_CORE |
| default y if AB3100_CORE |
| help |
| Select this to enable the AB3100 Mixed Signal IC OTP (one-time |
| programmable memory) support. This exposes a sysfs file to read |
| out OTP values. |
| |
| config EZX_PCAP |
| bool "PCAP Support" |
| depends on GENERIC_HARDIRQS && SPI_MASTER |
| help |
| This enables the PCAP ASIC present on EZX Phones. This is |
| needed for MMC, TouchScreen, Sound, USB, etc.. |
| |
| config AB8500_CORE |
| bool "ST-Ericsson AB8500 Mixed Signal Power Management chip" |
| depends on SPI=y && GENERIC_HARDIRQS |
| select MFD_CORE |
| help |
| Select this option to enable access to AB8500 power management |
| chip. This connects to U8500 on the SSP/SPI bus and exports |
| read/write functions for the devices to get access to this chip. |
| This chip embeds various other multimedia funtionalities as well. |
| |
| config AB3550_CORE |
| bool "ST-Ericsson AB3550 Mixed Signal Circuit core functions" |
| select MFD_CORE |
| depends on I2C=y && GENERIC_HARDIRQS && ABX500_CORE |
| help |
| Select this to enable the AB3550 Mixed Signal IC core |
| functionality. This connects to a AB3550 on the I2C bus |
| and expose a number of symbols needed for dependent devices |
| to read and write registers and subscribe to events from |
| this multi-functional IC. This is needed to use other features |
| of the AB3550 such as battery-backed RTC, charging control, |
| LEDs, vibrator, system power and temperature, power management |
| and ALSA sound. |
| |
| config MFD_TIMBERDALE |
| tristate "Support for the Timberdale FPGA" |
| select MFD_CORE |
| depends on PCI && GPIOLIB |
| ---help--- |
| This is the core driver for the timberdale FPGA. This device is a |
| multifunction device which exposes numerous platform devices. |
| |
| The timberdale FPGA can be found on the Intel Atom development board |
| for in-vehicle infontainment, called Russellville. |
| |
| config LPC_SCH |
| tristate "Intel SCH LPC" |
| depends on PCI |
| select MFD_CORE |
| help |
| LPC bridge function of the Intel SCH provides support for |
| System Management Bus and General Purpose I/O. |
| |
| config MFD_RDC321X |
| tristate "Support for RDC-R321x southbridge" |
| select MFD_CORE |
| depends on PCI |
| help |
| Say yes here if you want to have support for the RDC R-321x SoC |
| southbridge which provides access to GPIOs and Watchdog using the |
| southbridge PCI device configuration space. |
| |
| config MFD_JANZ_CMODIO |
| tristate "Support for Janz CMOD-IO PCI MODULbus Carrier Board" |
| select MFD_CORE |
| depends on PCI |
| help |
| This is the core driver for the Janz CMOD-IO PCI MODULbus |
| carrier board. This device is a PCI to MODULbus bridge which may |
| host many different types of MODULbus daughterboards, including |
| CAN and GPIO controllers. |
| |
| endif # MFD_SUPPORT |
| |
| menu "Multimedia Capabilities Port drivers" |
| depends on ARCH_SA1100 |
| |
| config MCP |
| tristate |
| |
| # Interface drivers |
| config MCP_SA11X0 |
| tristate "Support SA11x0 MCP interface" |
| depends on ARCH_SA1100 |
| select MCP |
| |
| # Chip drivers |
| config MCP_UCB1200 |
| tristate "Support for UCB1200 / UCB1300" |
| depends on MCP |
| |
| config MCP_UCB1200_TS |
| tristate "Touchscreen interface support" |
| depends on MCP_UCB1200 && INPUT |
| |
| endmenu |