diff --git a/Documentation/hwmon/twl4030-madc-hwmon b/Documentation/hwmon/twl4030-madc-hwmon
new file mode 100644
index 0000000..ef79843
--- /dev/null
+++ b/Documentation/hwmon/twl4030-madc-hwmon
@@ -0,0 +1,45 @@
+Kernel driver twl4030-madc
+=========================
+
+Supported chips:
+	* Texas Instruments TWL4030
+	Prefix: 'twl4030-madc'
+
+
+Authors:
+	J Keerthy <j-keerthy@ti.com>
+
+Description
+-----------
+
+The Texas Instruments TWL4030 is a Power Management and Audio Circuit. Among
+other things it contains a 10-bit A/D converter MADC. The converter has 16
+channels which can be used in different modes.
+
+
+See this table for the meaning of the different channels
+
+Channel Signal
+------------------------------------------
+0	Battery type(BTYPE)
+1	BCI: Battery temperature (BTEMP)
+2	GP analog input
+3	GP analog input
+4	GP analog input
+5	GP analog input
+6	GP analog input
+7	GP analog input
+8	BCI: VBUS voltage(VBUS)
+9	Backup Battery voltage (VBKP)
+10	BCI: Battery charger current (ICHG)
+11	BCI: Battery charger voltage (VCHG)
+12	BCI: Main battery voltage (VBAT)
+13	Reserved
+14	Reserved
+15	VRUSB Supply/Speaker left/Speaker right polarization level
+
+
+The Sysfs nodes will represent the voltage in the units of mV,
+the temperature channel shows the converted temperature in
+degree celcius. The Battery charging current channel represents
+battery charging current in mA.
diff --git a/arch/arm/mach-imx/mach-mx27_3ds.c b/arch/arm/mach-imx/mach-mx27_3ds.c
index 614b3c0..6e1accf 100644
--- a/arch/arm/mach-imx/mach-mx27_3ds.c
+++ b/arch/arm/mach-imx/mach-mx27_3ds.c
@@ -232,10 +232,13 @@
 };
 
 /* MC13783 */
-static struct mc13xxx_platform_data mc13783_pdata __initdata = {
-	.regulators = mx27_3ds_regulators,
-	.num_regulators = ARRAY_SIZE(mx27_3ds_regulators),
-	.flags  = MC13XXX_USE_REGULATOR,
+static struct mc13xxx_platform_data mc13783_pdata = {
+	.regulators = {
+		.regulators = mx27_3ds_regulators,
+		.num_regulators = ARRAY_SIZE(mx27_3ds_regulators),
+
+	},
+	.flags  = MC13783_USE_REGULATOR,
 };
 
 /* SPI */
diff --git a/arch/arm/mach-imx/mach-pcm038.c b/arch/arm/mach-imx/mach-pcm038.c
index 38c7708..4cbce6d 100644
--- a/arch/arm/mach-imx/mach-pcm038.c
+++ b/arch/arm/mach-imx/mach-pcm038.c
@@ -263,10 +263,12 @@
 };
 
 static struct mc13xxx_platform_data pcm038_pmic = {
-	.regulators = pcm038_regulators,
-	.num_regulators = ARRAY_SIZE(pcm038_regulators),
-	.flags = MC13XXX_USE_ADC | MC13XXX_USE_REGULATOR |
-		 MC13XXX_USE_TOUCHSCREEN,
+	.regulators = {
+		.regulators = pcm038_regulators,
+		.num_regulators = ARRAY_SIZE(pcm038_regulators),
+	},
+	.flags = MC13783_USE_ADC | MC13783_USE_REGULATOR |
+		 MC13783_USE_TOUCHSCREEN,
 };
 
 static struct spi_board_info pcm038_spi_board_info[] __initdata = {
diff --git a/arch/arm/mach-mx3/mach-mx31_3ds.c b/arch/arm/mach-mx3/mach-mx31_3ds.c
index 544d3e4..034be62 100644
--- a/arch/arm/mach-mx3/mach-mx31_3ds.c
+++ b/arch/arm/mach-mx3/mach-mx31_3ds.c
@@ -488,10 +488,12 @@
 };
 
 /* MC13783 */
-static struct mc13xxx_platform_data mc13783_pdata __initdata = {
-	.regulators = mx31_3ds_regulators,
-	.num_regulators = ARRAY_SIZE(mx31_3ds_regulators),
-	.flags  = MC13XXX_USE_REGULATOR | MC13XXX_USE_TOUCHSCREEN
+static struct mc13xxx_platform_data mc13783_pdata = {
+	.regulators = {
+		.regulators = mx31_3ds_regulators,
+		.num_regulators = ARRAY_SIZE(mx31_3ds_regulators),
+	},
+	.flags  = MC13783_USE_REGULATOR | MC13783_USE_TOUCHSCREEN,
 };
 
 /* SPI */
diff --git a/arch/arm/mach-mx3/mach-mx31moboard.c b/arch/arm/mach-mx3/mach-mx31moboard.c
index 6f3692b..3a021b0 100644
--- a/arch/arm/mach-mx3/mach-mx31moboard.c
+++ b/arch/arm/mach-mx3/mach-mx31moboard.c
@@ -268,8 +268,10 @@
 };
 
 static struct mc13xxx_platform_data moboard_pmic = {
-	.regulators = moboard_regulators,
-	.num_regulators = ARRAY_SIZE(moboard_regulators),
+	.regulators = {
+		.regulators = moboard_regulators,
+		.num_regulators = ARRAY_SIZE(moboard_regulators),
+	},
 	.leds = &moboard_leds,
 	.flags = MC13XXX_USE_REGULATOR | MC13XXX_USE_RTC |
 		MC13XXX_USE_ADC | MC13XXX_USE_LED,
diff --git a/arch/arm/mach-omap2/board-4430sdp.c b/arch/arm/mach-omap2/board-4430sdp.c
index 62c78de..56702c5 100644
--- a/arch/arm/mach-omap2/board-4430sdp.c
+++ b/arch/arm/mach-omap2/board-4430sdp.c
@@ -550,6 +550,12 @@
 	},
 };
 
+static struct regulator_init_data sdp4430_clk32kg = {
+	.constraints = {
+		.valid_ops_mask		= REGULATOR_CHANGE_STATUS,
+	},
+};
+
 static struct twl4030_platform_data sdp4430_twldata = {
 	.irq_base	= TWL6030_IRQ_BASE,
 	.irq_end	= TWL6030_IRQ_END,
@@ -565,6 +571,7 @@
 	.vaux1		= &sdp4430_vaux1,
 	.vaux2		= &sdp4430_vaux2,
 	.vaux3		= &sdp4430_vaux3,
+	.clk32kg	= &sdp4430_clk32kg,
 	.usb		= &omap4_usbphy_data
 };
 
diff --git a/arch/arm/mach-omap2/board-omap4panda.c b/arch/arm/mach-omap2/board-omap4panda.c
index 209cffb..c936c6d 100644
--- a/arch/arm/mach-omap2/board-omap4panda.c
+++ b/arch/arm/mach-omap2/board-omap4panda.c
@@ -411,6 +411,12 @@
 	},
 };
 
+static struct regulator_init_data omap4_panda_clk32kg = {
+	.constraints = {
+		.valid_ops_mask		= REGULATOR_CHANGE_STATUS,
+	},
+};
+
 static struct twl4030_platform_data omap4_panda_twldata = {
 	.irq_base	= TWL6030_IRQ_BASE,
 	.irq_end	= TWL6030_IRQ_END,
@@ -426,6 +432,7 @@
 	.vaux1		= &omap4_panda_vaux1,
 	.vaux2		= &omap4_panda_vaux2,
 	.vaux3		= &omap4_panda_vaux3,
+	.clk32kg	= &omap4_panda_clk32kg,
 	.usb		= &omap4_usbphy_data,
 };
 
diff --git a/arch/x86/platform/olpc/olpc-xo1.c b/arch/x86/platform/olpc/olpc-xo1.c
index 1277756..9951364 100644
--- a/arch/x86/platform/olpc/olpc-xo1.c
+++ b/arch/x86/platform/olpc/olpc-xo1.c
@@ -15,6 +15,7 @@
 #include <linux/module.h>
 #include <linux/platform_device.h>
 #include <linux/pm.h>
+#include <linux/mfd/core.h>
 
 #include <asm/io.h>
 #include <asm/olpc.h>
@@ -56,25 +57,24 @@
 static int __devinit olpc_xo1_probe(struct platform_device *pdev)
 {
 	struct resource *res;
+	int err;
 
 	/* don't run on non-XOs */
 	if (!machine_is_olpc())
 		return -ENODEV;
 
+	err = mfd_cell_enable(pdev);
+	if (err)
+		return err;
+
 	res = platform_get_resource(pdev, IORESOURCE_IO, 0);
 	if (!res) {
 		dev_err(&pdev->dev, "can't fetch device resource info\n");
 		return -EIO;
 	}
-
-	if (!request_region(res->start, resource_size(res), DRV_NAME)) {
-		dev_err(&pdev->dev, "can't request region\n");
-		return -EIO;
-	}
-
-	if (strcmp(pdev->name, "cs5535-pms") == 0)
+	if (strcmp(pdev->name, "olpc-xo1-pms") == 0)
 		pms_base = res->start;
-	else if (strcmp(pdev->name, "cs5535-acpi") == 0)
+	else if (strcmp(pdev->name, "olpc-xo1-ac-acpi") == 0)
 		acpi_base = res->start;
 
 	/* If we have both addresses, we can override the poweroff hook */
@@ -88,14 +88,11 @@
 
 static int __devexit olpc_xo1_remove(struct platform_device *pdev)
 {
-	struct resource *r;
+	mfd_cell_disable(pdev);
 
-	r = platform_get_resource(pdev, IORESOURCE_IO, 0);
-	release_region(r->start, resource_size(r));
-
-	if (strcmp(pdev->name, "cs5535-pms") == 0)
+	if (strcmp(pdev->name, "olpc-xo1-pms") == 0)
 		pms_base = 0;
-	else if (strcmp(pdev->name, "cs5535-acpi") == 0)
+	else if (strcmp(pdev->name, "olpc-xo1-acpi") == 0)
 		acpi_base = 0;
 
 	pm_power_off = NULL;
@@ -104,7 +101,7 @@
 
 static struct platform_driver cs5535_pms_drv = {
 	.driver = {
-		.name = "cs5535-pms",
+		.name = "olpc-xo1-pms",
 		.owner = THIS_MODULE,
 	},
 	.probe = olpc_xo1_probe,
@@ -113,7 +110,7 @@
 
 static struct platform_driver cs5535_acpi_drv = {
 	.driver = {
-		.name = "cs5535-acpi",
+		.name = "olpc-xo1-acpi",
 		.owner = THIS_MODULE,
 	},
 	.probe = olpc_xo1_probe,
@@ -124,26 +121,27 @@
 {
 	int r;
 
-	r = platform_driver_register(&cs5535_pms_drv);
+	r = mfd_shared_platform_driver_register(&cs5535_pms_drv, "cs5535-pms");
 	if (r)
 		return r;
 
-	r = platform_driver_register(&cs5535_acpi_drv);
+	r = mfd_shared_platform_driver_register(&cs5535_acpi_drv,
+			"cs5535-acpi");
 	if (r)
-		platform_driver_unregister(&cs5535_pms_drv);
+		mfd_shared_platform_driver_unregister(&cs5535_pms_drv);
 
 	return r;
 }
 
 static void __exit olpc_xo1_exit(void)
 {
-	platform_driver_unregister(&cs5535_acpi_drv);
-	platform_driver_unregister(&cs5535_pms_drv);
+	mfd_shared_platform_driver_unregister(&cs5535_acpi_drv);
+	mfd_shared_platform_driver_unregister(&cs5535_pms_drv);
 }
 
 MODULE_AUTHOR("Daniel Drake <dsd@laptop.org>");
 MODULE_LICENSE("GPL");
-MODULE_ALIAS("platform:olpc-xo1");
+MODULE_ALIAS("platform:cs5535-pms");
 
 module_init(olpc_xo1_init);
 module_exit(olpc_xo1_exit);
diff --git a/drivers/dma/timb_dma.c b/drivers/dma/timb_dma.c
index f69f90a..d2c75fe 100644
--- a/drivers/dma/timb_dma.c
+++ b/drivers/dma/timb_dma.c
@@ -27,6 +27,7 @@
 #include <linux/io.h>
 #include <linux/module.h>
 #include <linux/platform_device.h>
+#include <linux/mfd/core.h>
 #include <linux/slab.h>
 
 #include <linux/timb_dma.h>
@@ -684,7 +685,7 @@
 
 static int __devinit td_probe(struct platform_device *pdev)
 {
-	struct timb_dma_platform_data *pdata = pdev->dev.platform_data;
+	struct timb_dma_platform_data *pdata = mfd_get_data(pdev);
 	struct timb_dma *td;
 	struct resource *iomem;
 	int irq;
diff --git a/drivers/gpio/Kconfig b/drivers/gpio/Kconfig
index b46442d..d8d0cda 100644
--- a/drivers/gpio/Kconfig
+++ b/drivers/gpio/Kconfig
@@ -100,18 +100,21 @@
 	  Say yes here to support the NEC VR4100 series General-purpose I/O Uint
 
 config GPIO_SCH
-	tristate "Intel SCH GPIO"
+	tristate "Intel SCH/TunnelCreek GPIO"
 	depends on GPIOLIB && PCI && X86
 	select MFD_CORE
 	select LPC_SCH
 	help
-	  Say yes here to support GPIO interface on Intel Poulsbo SCH.
+	  Say yes here to support GPIO interface on Intel Poulsbo SCH
+	  or Intel Tunnel Creek processor.
 	  The Intel SCH contains a total of 14 GPIO pins. Ten GPIOs are
 	  powered by the core power rail and are turned off during sleep
 	  modes (S3 and higher). The remaining four GPIOs are powered by
 	  the Intel SCH suspend power supply. These GPIOs remain
 	  active during S3. The suspend powered GPIOs can be used to wake the
 	  system from the Suspend-to-RAM state.
+	  The Intel Tunnel Creek processor has 5 GPIOs powered by the
+	  core power rail and 9 from suspend power supply.
 
 	  This driver can also be built as a module. If so, the module
 	  will be called sch-gpio.
diff --git a/drivers/gpio/janz-ttl.c b/drivers/gpio/janz-ttl.c
index 813ac07..2514fb0 100644
--- a/drivers/gpio/janz-ttl.c
+++ b/drivers/gpio/janz-ttl.c
@@ -15,6 +15,7 @@
 #include <linux/interrupt.h>
 #include <linux/delay.h>
 #include <linux/platform_device.h>
+#include <linux/mfd/core.h>
 #include <linux/io.h>
 #include <linux/gpio.h>
 #include <linux/slab.h>
@@ -149,7 +150,7 @@
 	struct resource *res;
 	int ret;
 
-	pdata = pdev->dev.platform_data;
+	pdata = mfd_get_data(pdev);
 	if (!pdata) {
 		dev_err(dev, "no platform data\n");
 		ret = -ENXIO;
diff --git a/drivers/gpio/rdc321x-gpio.c b/drivers/gpio/rdc321x-gpio.c
index 897e057..a9bda88 100644
--- a/drivers/gpio/rdc321x-gpio.c
+++ b/drivers/gpio/rdc321x-gpio.c
@@ -27,6 +27,7 @@
 #include <linux/pci.h>
 #include <linux/gpio.h>
 #include <linux/mfd/rdc321x.h>
+#include <linux/mfd/core.h>
 #include <linux/slab.h>
 
 struct rdc321x_gpio {
@@ -135,7 +136,7 @@
 	struct rdc321x_gpio *rdc321x_gpio_dev;
 	struct rdc321x_gpio_pdata *pdata;
 
-	pdata = platform_get_drvdata(pdev);
+	pdata = mfd_get_data(pdev);
 	if (!pdata) {
 		dev_err(&pdev->dev, "no platform data supplied\n");
 		return -ENODEV;
diff --git a/drivers/gpio/sch_gpio.c b/drivers/gpio/sch_gpio.c
index 5835213..5606042 100644
--- a/drivers/gpio/sch_gpio.c
+++ b/drivers/gpio/sch_gpio.c
@@ -25,6 +25,7 @@
 #include <linux/errno.h>
 #include <linux/acpi.h>
 #include <linux/platform_device.h>
+#include <linux/pci_ids.h>
 
 #include <linux/gpio.h>
 
@@ -187,7 +188,11 @@
 static int __devinit sch_gpio_probe(struct platform_device *pdev)
 {
 	struct resource *res;
-	int err;
+	int err, id;
+
+	id = pdev->id;
+	if (!id)
+		return -ENODEV;
 
 	res = platform_get_resource(pdev, IORESOURCE_IO, 0);
 	if (!res)
@@ -198,12 +203,40 @@
 
 	gpio_ba = res->start;
 
-	sch_gpio_core.base = 0;
-	sch_gpio_core.ngpio = 10;
-	sch_gpio_core.dev = &pdev->dev;
+	switch (id) {
+		case PCI_DEVICE_ID_INTEL_SCH_LPC:
+			sch_gpio_core.base = 0;
+			sch_gpio_core.ngpio = 10;
 
-	sch_gpio_resume.base = 10;
-	sch_gpio_resume.ngpio = 4;
+			sch_gpio_resume.base = 10;
+			sch_gpio_resume.ngpio = 4;
+
+			/*
+			 * GPIO[6:0] enabled by default
+			 * GPIO7 is configured by the CMC as SLPIOVR
+			 * Enable GPIO[9:8] core powered gpios explicitly
+			 */
+			outb(0x3, gpio_ba + CGEN + 1);
+			/*
+			 * SUS_GPIO[2:0] enabled by default
+			 * Enable SUS_GPIO3 resume powered gpio explicitly
+			 */
+			outb(0x8, gpio_ba + RGEN);
+			break;
+
+		case PCI_DEVICE_ID_INTEL_ITC_LPC:
+			sch_gpio_core.base = 0;
+			sch_gpio_core.ngpio = 5;
+
+			sch_gpio_resume.base = 5;
+			sch_gpio_resume.ngpio = 9;
+			break;
+
+		default:
+			return -ENODEV;
+	}
+
+	sch_gpio_core.dev = &pdev->dev;
 	sch_gpio_resume.dev = &pdev->dev;
 
 	err = gpiochip_add(&sch_gpio_core);
@@ -214,18 +247,6 @@
 	if (err < 0)
 		goto err_sch_gpio_resume;
 
-	/*
-	 * GPIO[6:0] enabled by default
-	 * GPIO7 is configured by the CMC as SLPIOVR
-	 * Enable GPIO[9:8] core powered gpios explicitly
-	 */
-	outb(0x3, gpio_ba + CGEN + 1);
-	/*
-	 * SUS_GPIO[2:0] enabled by default
-	 * Enable SUS_GPIO3 resume powered gpio explicitly
-	 */
-	outb(0x8, gpio_ba + RGEN);
-
 	return 0;
 
 err_sch_gpio_resume:
diff --git a/drivers/gpio/timbgpio.c b/drivers/gpio/timbgpio.c
index 58c8f30..ffcd815 100644
--- a/drivers/gpio/timbgpio.c
+++ b/drivers/gpio/timbgpio.c
@@ -23,6 +23,7 @@
 #include <linux/module.h>
 #include <linux/gpio.h>
 #include <linux/platform_device.h>
+#include <linux/mfd/core.h>
 #include <linux/irq.h>
 #include <linux/io.h>
 #include <linux/timb_gpio.h>
@@ -228,7 +229,7 @@
 	struct gpio_chip *gc;
 	struct timbgpio *tgpio;
 	struct resource *iomem;
-	struct timbgpio_platform_data *pdata = pdev->dev.platform_data;
+	struct timbgpio_platform_data *pdata = mfd_get_data(pdev);
 	int irq = platform_get_irq(pdev, 0);
 
 	if (!pdata || pdata->nr_pins > 32) {
@@ -319,14 +320,13 @@
 static int __devexit timbgpio_remove(struct platform_device *pdev)
 {
 	int err;
-	struct timbgpio_platform_data *pdata = pdev->dev.platform_data;
 	struct timbgpio *tgpio = platform_get_drvdata(pdev);
 	struct resource *iomem = platform_get_resource(pdev, IORESOURCE_MEM, 0);
 	int irq = platform_get_irq(pdev, 0);
 
 	if (irq >= 0 && tgpio->irq_base > 0) {
 		int i;
-		for (i = 0; i < pdata->nr_pins; i++) {
+		for (i = 0; i < tgpio->gpio.ngpio; i++) {
 			set_irq_chip(tgpio->irq_base + i, NULL);
 			set_irq_chip_data(tgpio->irq_base + i, NULL);
 		}
diff --git a/drivers/hwmon/Kconfig b/drivers/hwmon/Kconfig
index e4bd13b..81131ed 100644
--- a/drivers/hwmon/Kconfig
+++ b/drivers/hwmon/Kconfig
@@ -1047,6 +1047,16 @@
 	  This driver can also be built as a module.  If so, the module
 	  will be called tmp421.
 
+config SENSORS_TWL4030_MADC
+	tristate "Texas Instruments TWL4030 MADC Hwmon"
+	depends on TWL4030_MADC
+	help
+	If you say yes here you get hwmon support for triton
+	TWL4030-MADC.
+
+	This driver can also be built as a module. If so it will be called
+	twl4030-madc-hwmon.
+
 config SENSORS_VIA_CPUTEMP
 	tristate "VIA CPU temperature sensor"
 	depends on X86
diff --git a/drivers/hwmon/Makefile b/drivers/hwmon/Makefile
index 54ca593..967d0ea 100644
--- a/drivers/hwmon/Makefile
+++ b/drivers/hwmon/Makefile
@@ -104,6 +104,7 @@
 obj-$(CONFIG_SENSORS_TMP102)	+= tmp102.o
 obj-$(CONFIG_SENSORS_TMP401)	+= tmp401.o
 obj-$(CONFIG_SENSORS_TMP421)	+= tmp421.o
+obj-$(CONFIG_SENSORS_TWL4030_MADC)+= twl4030-madc-hwmon.o
 obj-$(CONFIG_SENSORS_VIA_CPUTEMP)+= via-cputemp.o
 obj-$(CONFIG_SENSORS_VIA686A)	+= via686a.o
 obj-$(CONFIG_SENSORS_VT1211)	+= vt1211.o
diff --git a/drivers/hwmon/jz4740-hwmon.c b/drivers/hwmon/jz4740-hwmon.c
index 1c8b3d9..fea292d 100644
--- a/drivers/hwmon/jz4740-hwmon.c
+++ b/drivers/hwmon/jz4740-hwmon.c
@@ -32,7 +32,7 @@
 
 	int irq;
 
-	struct mfd_cell *cell;
+	const struct mfd_cell *cell;
 	struct device *hwmon;
 
 	struct completion read_completion;
@@ -112,7 +112,7 @@
 		return -ENOMEM;
 	}
 
-	hwmon->cell = pdev->dev.platform_data;
+	hwmon->cell = mfd_get_cell(pdev);
 
 	hwmon->irq = platform_get_irq(pdev, 0);
 	if (hwmon->irq < 0) {
diff --git a/drivers/hwmon/twl4030-madc-hwmon.c b/drivers/hwmon/twl4030-madc-hwmon.c
new file mode 100644
index 0000000..97e22be
--- /dev/null
+++ b/drivers/hwmon/twl4030-madc-hwmon.c
@@ -0,0 +1,157 @@
+/*
+ *
+ * TWL4030 MADC Hwmon driver-This driver monitors the real time
+ * conversion of analog signals like battery temperature,
+ * battery type, battery level etc. User can ask for the conversion on a
+ * particular channel using the sysfs nodes.
+ *
+ * Copyright (C) 2011 Texas Instruments Incorporated - http://www.ti.com/
+ * J Keerthy <j-keerthy@ti.com>
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License
+ * version 2 as published by the Free Software Foundation.
+ *
+ * This program is distributed in the hope that it will be useful, but
+ * WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the GNU
+ * General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA
+ * 02110-1301 USA
+ *
+ */
+#include <linux/init.h>
+#include <linux/module.h>
+#include <linux/kernel.h>
+#include <linux/i2c/twl.h>
+#include <linux/device.h>
+#include <linux/platform_device.h>
+#include <linux/i2c/twl4030-madc.h>
+#include <linux/hwmon.h>
+#include <linux/hwmon-sysfs.h>
+#include <linux/stddef.h>
+#include <linux/sysfs.h>
+#include <linux/err.h>
+#include <linux/types.h>
+
+/*
+ * sysfs hook function
+ */
+static ssize_t madc_read(struct device *dev,
+			 struct device_attribute *devattr, char *buf)
+{
+	struct sensor_device_attribute *attr = to_sensor_dev_attr(devattr);
+	struct twl4030_madc_request req;
+	long val;
+
+	req.channels = (1 << attr->index);
+	req.method = TWL4030_MADC_SW2;
+	req.func_cb = NULL;
+	val = twl4030_madc_conversion(&req);
+	if (val < 0)
+		return val;
+
+	return sprintf(buf, "%d\n", req.rbuf[attr->index]);
+}
+
+/* sysfs nodes to read individual channels from user side */
+static SENSOR_DEVICE_ATTR(in0_input, S_IRUGO, madc_read, NULL, 0);
+static SENSOR_DEVICE_ATTR(temp1_input, S_IRUGO, madc_read, NULL, 1);
+static SENSOR_DEVICE_ATTR(in2_input, S_IRUGO, madc_read, NULL, 2);
+static SENSOR_DEVICE_ATTR(in3_input, S_IRUGO, madc_read, NULL, 3);
+static SENSOR_DEVICE_ATTR(in4_input, S_IRUGO, madc_read, NULL, 4);
+static SENSOR_DEVICE_ATTR(in5_input, S_IRUGO, madc_read, NULL, 5);
+static SENSOR_DEVICE_ATTR(in6_input, S_IRUGO, madc_read, NULL, 6);
+static SENSOR_DEVICE_ATTR(in7_input, S_IRUGO, madc_read, NULL, 7);
+static SENSOR_DEVICE_ATTR(in8_input, S_IRUGO, madc_read, NULL, 8);
+static SENSOR_DEVICE_ATTR(in9_input, S_IRUGO, madc_read, NULL, 9);
+static SENSOR_DEVICE_ATTR(curr10_input, S_IRUGO, madc_read, NULL, 10);
+static SENSOR_DEVICE_ATTR(in11_input, S_IRUGO, madc_read, NULL, 11);
+static SENSOR_DEVICE_ATTR(in12_input, S_IRUGO, madc_read, NULL, 12);
+static SENSOR_DEVICE_ATTR(in15_input, S_IRUGO, madc_read, NULL, 15);
+
+static struct attribute *twl4030_madc_attributes[] = {
+	&sensor_dev_attr_in0_input.dev_attr.attr,
+	&sensor_dev_attr_temp1_input.dev_attr.attr,
+	&sensor_dev_attr_in2_input.dev_attr.attr,
+	&sensor_dev_attr_in3_input.dev_attr.attr,
+	&sensor_dev_attr_in4_input.dev_attr.attr,
+	&sensor_dev_attr_in5_input.dev_attr.attr,
+	&sensor_dev_attr_in6_input.dev_attr.attr,
+	&sensor_dev_attr_in7_input.dev_attr.attr,
+	&sensor_dev_attr_in8_input.dev_attr.attr,
+	&sensor_dev_attr_in9_input.dev_attr.attr,
+	&sensor_dev_attr_curr10_input.dev_attr.attr,
+	&sensor_dev_attr_in11_input.dev_attr.attr,
+	&sensor_dev_attr_in12_input.dev_attr.attr,
+	&sensor_dev_attr_in15_input.dev_attr.attr,
+	NULL
+};
+
+static const struct attribute_group twl4030_madc_group = {
+	.attrs = twl4030_madc_attributes,
+};
+
+static int __devinit twl4030_madc_hwmon_probe(struct platform_device *pdev)
+{
+	int ret;
+	int status;
+	struct device *hwmon;
+
+	ret = sysfs_create_group(&pdev->dev.kobj, &twl4030_madc_group);
+	if (ret)
+		goto err_sysfs;
+	hwmon = hwmon_device_register(&pdev->dev);
+	if (IS_ERR(hwmon)) {
+		dev_err(&pdev->dev, "hwmon_device_register failed.\n");
+		status = PTR_ERR(hwmon);
+		goto err_reg;
+	}
+
+	return 0;
+
+err_reg:
+	sysfs_remove_group(&pdev->dev.kobj, &twl4030_madc_group);
+err_sysfs:
+
+	return ret;
+}
+
+static int __devexit twl4030_madc_hwmon_remove(struct platform_device *pdev)
+{
+	hwmon_device_unregister(&pdev->dev);
+	sysfs_remove_group(&pdev->dev.kobj, &twl4030_madc_group);
+
+	return 0;
+}
+
+static struct platform_driver twl4030_madc_hwmon_driver = {
+	.probe = twl4030_madc_hwmon_probe,
+	.remove = __exit_p(twl4030_madc_hwmon_remove),
+	.driver = {
+		   .name = "twl4030_madc_hwmon",
+		   .owner = THIS_MODULE,
+		   },
+};
+
+static int __init twl4030_madc_hwmon_init(void)
+{
+	return platform_driver_register(&twl4030_madc_hwmon_driver);
+}
+
+module_init(twl4030_madc_hwmon_init);
+
+static void __exit twl4030_madc_hwmon_exit(void)
+{
+	platform_driver_unregister(&twl4030_madc_hwmon_driver);
+}
+
+module_exit(twl4030_madc_hwmon_exit);
+
+MODULE_DESCRIPTION("TWL4030 ADC Hwmon driver");
+MODULE_LICENSE("GPL");
+MODULE_AUTHOR("J Keerthy");
+MODULE_ALIAS("twl4030_madc_hwmon");
diff --git a/drivers/i2c/busses/i2c-ocores.c b/drivers/i2c/busses/i2c-ocores.c
index 1b46a9d..fee1a26 100644
--- a/drivers/i2c/busses/i2c-ocores.c
+++ b/drivers/i2c/busses/i2c-ocores.c
@@ -49,6 +49,7 @@
 #include <linux/init.h>
 #include <linux/errno.h>
 #include <linux/platform_device.h>
+#include <linux/mfd/core.h>
 #include <linux/i2c.h>
 #include <linux/interrupt.h>
 #include <linux/wait.h>
@@ -305,7 +306,7 @@
 		return -EIO;
 	}
 
-	pdata = pdev->dev.platform_data;
+	pdata = mfd_get_data(pdev);
 	if (pdata) {
 		i2c->regstep = pdata->regstep;
 		i2c->clock_khz = pdata->clock_khz;
diff --git a/drivers/i2c/busses/i2c-xiic.c b/drivers/i2c/busses/i2c-xiic.c
index a9c419e..9fbd7e6 100644
--- a/drivers/i2c/busses/i2c-xiic.c
+++ b/drivers/i2c/busses/i2c-xiic.c
@@ -34,6 +34,7 @@
 #include <linux/errno.h>
 #include <linux/delay.h>
 #include <linux/platform_device.h>
+#include <linux/mfd/core.h>
 #include <linux/i2c.h>
 #include <linux/interrupt.h>
 #include <linux/wait.h>
@@ -704,7 +705,7 @@
 	if (irq < 0)
 		goto resource_missing;
 
-	pdata = (struct xiic_i2c_platform_data *) pdev->dev.platform_data;
+	pdata = mfd_get_data(pdev);
 	if (!pdata)
 		return -EINVAL;
 
diff --git a/drivers/input/misc/88pm860x_onkey.c b/drivers/input/misc/88pm860x_onkey.c
index 4cc8282..3dca3c1 100644
--- a/drivers/input/misc/88pm860x_onkey.c
+++ b/drivers/input/misc/88pm860x_onkey.c
@@ -74,7 +74,7 @@
 	info->chip = chip;
 	info->i2c = (chip->id == CHIP_PM8607) ? chip->client : chip->companion;
 	info->dev = &pdev->dev;
-	info->irq = irq + chip->irq_base;
+	info->irq = irq;
 
 	info->idev = input_allocate_device();
 	if (!info->idev) {
diff --git a/drivers/input/misc/twl4030-vibra.c b/drivers/input/misc/twl4030-vibra.c
index 014dd4a..6a11694 100644
--- a/drivers/input/misc/twl4030-vibra.c
+++ b/drivers/input/misc/twl4030-vibra.c
@@ -29,6 +29,7 @@
 #include <linux/workqueue.h>
 #include <linux/i2c/twl.h>
 #include <linux/mfd/twl4030-codec.h>
+#include <linux/mfd/core.h>
 #include <linux/input.h>
 #include <linux/slab.h>
 
@@ -196,7 +197,7 @@
 
 static int __devinit twl4030_vibra_probe(struct platform_device *pdev)
 {
-	struct twl4030_codec_vibra_data *pdata = pdev->dev.platform_data;
+	struct twl4030_codec_vibra_data *pdata = mfd_get_data(pdev);
 	struct vibra_info *info;
 	int ret;
 
diff --git a/drivers/leds/leds-88pm860x.c b/drivers/leds/leds-88pm860x.c
index e672b44..416def8 100644
--- a/drivers/leds/leds-88pm860x.c
+++ b/drivers/leds/leds-88pm860x.c
@@ -17,6 +17,7 @@
 #include <linux/leds.h>
 #include <linux/slab.h>
 #include <linux/workqueue.h>
+#include <linux/mfd/core.h>
 #include <linux/mfd/88pm860x.h>
 
 #define LED_PWM_SHIFT		(3)
@@ -118,7 +119,8 @@
 
 	struct pm860x_led *led;
 	struct pm860x_chip *chip;
-	int mask;
+	unsigned char buf[3];
+	int mask, ret;
 
 	led = container_of(work, struct pm860x_led, work);
 	chip = led->chip;
@@ -128,16 +130,27 @@
 			pm860x_set_bits(led->i2c, __led_off(led->port),
 					LED_CURRENT_MASK, led->iset);
 		}
+		pm860x_set_bits(led->i2c, __blink_off(led->port),
+				LED_BLINK_MASK, LED_ON_CONTINUOUS);
 		mask = __blink_ctl_mask(led->port);
 		pm860x_set_bits(led->i2c, PM8606_WLED3B, mask, mask);
-	} else if (led->brightness == 0) {
-		pm860x_set_bits(led->i2c, __led_off(led->port),
-				LED_CURRENT_MASK, 0);
-		mask = __blink_ctl_mask(led->port);
-		pm860x_set_bits(led->i2c, PM8606_WLED3B, mask, 0);
 	}
 	pm860x_set_bits(led->i2c, __led_off(led->port), LED_PWM_MASK,
 			led->brightness);
+
+	if (led->brightness == 0) {
+		pm860x_bulk_read(led->i2c, __led_off(led->port), 3, buf);
+		ret = buf[0] & LED_PWM_MASK;
+		ret |= buf[1] & LED_PWM_MASK;
+		ret |= buf[2] & LED_PWM_MASK;
+		if (ret == 0) {
+			/* unset current since no led is lighting */
+			pm860x_set_bits(led->i2c, __led_off(led->port),
+					LED_CURRENT_MASK, 0);
+			mask = __blink_ctl_mask(led->port);
+			pm860x_set_bits(led->i2c, PM8606_WLED3B, mask, 0);
+		}
+	}
 	led->current_brightness = led->brightness;
 	dev_dbg(chip->dev, "Update LED. (reg:%d, brightness:%d)\n",
 		__led_off(led->port), led->brightness);
@@ -153,31 +166,12 @@
 	schedule_work(&data->work);
 }
 
-static int __check_device(struct pm860x_led_pdata *pdata, char *name)
-{
-	struct pm860x_led_pdata *p = pdata;
-	int ret = -EINVAL;
-
-	while (p && p->id) {
-		if ((p->id != PM8606_ID_LED) || (p->flags < 0))
-			break;
-
-		if (!strncmp(name, pm860x_led_name[p->flags],
-			MFD_NAME_SIZE)) {
-			ret = (int)p->flags;
-			break;
-		}
-		p++;
-	}
-	return ret;
-}
-
 static int pm860x_led_probe(struct platform_device *pdev)
 {
 	struct pm860x_chip *chip = dev_get_drvdata(pdev->dev.parent);
-	struct pm860x_platform_data *pm860x_pdata;
 	struct pm860x_led_pdata *pdata;
 	struct pm860x_led *data;
+	struct mfd_cell *cell;
 	struct resource *res;
 	int ret;
 
@@ -187,10 +181,11 @@
 		return -EINVAL;
 	}
 
-	if (pdev->dev.parent->platform_data) {
-		pm860x_pdata = pdev->dev.parent->platform_data;
-		pdata = pm860x_pdata->led;
-	} else {
+	cell = pdev->dev.platform_data;
+	if (cell == NULL)
+		return -ENODEV;
+	pdata = cell->mfd_data;
+	if (pdata == NULL) {
 		dev_err(&pdev->dev, "No platform data!\n");
 		return -EINVAL;
 	}
@@ -198,12 +193,12 @@
 	data = kzalloc(sizeof(struct pm860x_led), GFP_KERNEL);
 	if (data == NULL)
 		return -ENOMEM;
-	strncpy(data->name, res->name, MFD_NAME_SIZE);
+	strncpy(data->name, res->name, MFD_NAME_SIZE - 1);
 	dev_set_drvdata(&pdev->dev, data);
 	data->chip = chip;
 	data->i2c = (chip->id == CHIP_PM8606) ? chip->client : chip->companion;
 	data->iset = pdata->iset;
-	data->port = __check_device(pdata, data->name);
+	data->port = pdata->flags;
 	if (data->port < 0) {
 		dev_err(&pdev->dev, "check device failed\n");
 		kfree(data);
@@ -221,6 +216,7 @@
 		dev_err(&pdev->dev, "Failed to register LED: %d\n", ret);
 		goto out;
 	}
+	pm860x_led_set(&data->cdev, 0);
 	return 0;
 out:
 	kfree(data);
diff --git a/drivers/leds/leds-mc13783.c b/drivers/leds/leds-mc13783.c
index f05bb08..06a5bb4 100644
--- a/drivers/leds/leds-mc13783.c
+++ b/drivers/leds/leds-mc13783.c
@@ -22,6 +22,7 @@
 #include <linux/leds.h>
 #include <linux/workqueue.h>
 #include <linux/mfd/mc13783.h>
+#include <linux/mfd/core.h>
 #include <linux/slab.h>
 
 struct mc13783_led {
@@ -183,7 +184,7 @@
 
 static int __devinit mc13783_leds_prepare(struct platform_device *pdev)
 {
-	struct mc13783_leds_platform_data *pdata = dev_get_platdata(&pdev->dev);
+	struct mc13783_leds_platform_data *pdata = mfd_get_data(pdev);
 	struct mc13783 *dev = dev_get_drvdata(pdev->dev.parent);
 	int ret = 0;
 	int reg = 0;
@@ -264,7 +265,7 @@
 
 static int __devinit mc13783_led_probe(struct platform_device *pdev)
 {
-	struct mc13783_leds_platform_data *pdata = dev_get_platdata(&pdev->dev);
+	struct mc13783_leds_platform_data *pdata = mfd_get_data(pdev);
 	struct mc13783_led_platform_data *led_cur;
 	struct mc13783_led *led, *led_dat;
 	int ret, i;
@@ -351,7 +352,7 @@
 
 static int __devexit mc13783_led_remove(struct platform_device *pdev)
 {
-	struct mc13783_leds_platform_data *pdata = dev_get_platdata(&pdev->dev);
+	struct mc13783_leds_platform_data *pdata = mfd_get_data(pdev);
 	struct mc13783_led *led = platform_get_drvdata(pdev);
 	struct mc13783 *dev = dev_get_drvdata(pdev->dev.parent);
 	int i;
diff --git a/drivers/media/radio/radio-timb.c b/drivers/media/radio/radio-timb.c
index a185610..1e3a8dd 100644
--- a/drivers/media/radio/radio-timb.c
+++ b/drivers/media/radio/radio-timb.c
@@ -21,6 +21,7 @@
 #include <media/v4l2-ioctl.h>
 #include <media/v4l2-device.h>
 #include <linux/platform_device.h>
+#include <linux/mfd/core.h>
 #include <linux/interrupt.h>
 #include <linux/slab.h>
 #include <linux/i2c.h>
@@ -148,7 +149,7 @@
 
 static int __devinit timbradio_probe(struct platform_device *pdev)
 {
-	struct timb_radio_platform_data *pdata = pdev->dev.platform_data;
+	struct timb_radio_platform_data *pdata = mfd_get_data(pdev);
 	struct timbradio *tr;
 	int err;
 
diff --git a/drivers/media/radio/radio-wl1273.c b/drivers/media/radio/radio-wl1273.c
index 7ecc8e6..4698eb0 100644
--- a/drivers/media/radio/radio-wl1273.c
+++ b/drivers/media/radio/radio-wl1273.c
@@ -2138,7 +2138,7 @@
 
 static int __devinit wl1273_fm_radio_probe(struct platform_device *pdev)
 {
-	struct wl1273_core **core = pdev->dev.platform_data;
+	struct wl1273_core **core = mfd_get_data(pdev);
 	struct wl1273_device *radio;
 	struct v4l2_ctrl *ctrl;
 	int r = 0;
diff --git a/drivers/media/video/timblogiw.c b/drivers/media/video/timblogiw.c
index fc611eb..84d4c7c 100644
--- a/drivers/media/video/timblogiw.c
+++ b/drivers/media/video/timblogiw.c
@@ -24,6 +24,7 @@
 #include <linux/platform_device.h>
 #include <linux/slab.h>
 #include <linux/dmaengine.h>
+#include <linux/mfd/core.h>
 #include <linux/scatterlist.h>
 #include <linux/interrupt.h>
 #include <linux/list.h>
@@ -790,7 +791,7 @@
 {
 	int err;
 	struct timblogiw *lw = NULL;
-	struct timb_video_platform_data *pdata = pdev->dev.platform_data;
+	struct timb_video_platform_data *pdata = mfd_get_data(pdev);
 
 	if (!pdata) {
 		dev_err(&pdev->dev, "No platform data\n");
diff --git a/drivers/mfd/88pm860x-core.c b/drivers/mfd/88pm860x-core.c
index 793300c..9c511c1 100644
--- a/drivers/mfd/88pm860x-core.c
+++ b/drivers/mfd/88pm860x-core.c
@@ -17,229 +17,137 @@
 #include <linux/platform_device.h>
 #include <linux/mfd/core.h>
 #include <linux/mfd/88pm860x.h>
+#include <linux/regulator/machine.h>
 
 #define INT_STATUS_NUM			3
 
-char pm860x_backlight_name[][MFD_NAME_SIZE] = {
-	"backlight-0",
-	"backlight-1",
-	"backlight-2",
-};
-EXPORT_SYMBOL(pm860x_backlight_name);
-
-char pm860x_led_name[][MFD_NAME_SIZE] = {
-	"led0-red",
-	"led0-green",
-	"led0-blue",
-	"led1-red",
-	"led1-green",
-	"led1-blue",
-};
-EXPORT_SYMBOL(pm860x_led_name);
-
-#define PM8606_BACKLIGHT_RESOURCE(_i, _x)		\
-{							\
-	.name	= pm860x_backlight_name[_i],		\
-	.start	= PM8606_##_x,				\
-	.end	= PM8606_##_x,				\
-	.flags	= IORESOURCE_IO,			\
-}
-
-static struct resource backlight_resources[] = {
-	PM8606_BACKLIGHT_RESOURCE(PM8606_BACKLIGHT1, WLED1A),
-	PM8606_BACKLIGHT_RESOURCE(PM8606_BACKLIGHT2, WLED2A),
-	PM8606_BACKLIGHT_RESOURCE(PM8606_BACKLIGHT3, WLED3A),
+static struct resource bk_resources[] __initdata = {
+	{PM8606_BACKLIGHT1, PM8606_BACKLIGHT1, "backlight-0", IORESOURCE_IO,},
+	{PM8606_BACKLIGHT2, PM8606_BACKLIGHT2, "backlight-1", IORESOURCE_IO,},
+	{PM8606_BACKLIGHT3, PM8606_BACKLIGHT3, "backlight-2", IORESOURCE_IO,},
 };
 
-#define PM8606_BACKLIGHT_DEVS(_i)			\
-{							\
-	.name		= "88pm860x-backlight",		\
-	.num_resources	= 1,				\
-	.resources	= &backlight_resources[_i],	\
-	.id		= _i,				\
-}
-
-static struct mfd_cell backlight_devs[] = {
-	PM8606_BACKLIGHT_DEVS(PM8606_BACKLIGHT1),
-	PM8606_BACKLIGHT_DEVS(PM8606_BACKLIGHT2),
-	PM8606_BACKLIGHT_DEVS(PM8606_BACKLIGHT3),
+static struct resource led_resources[] __initdata = {
+	{PM8606_LED1_RED,   PM8606_LED1_RED,   "led0-red",   IORESOURCE_IO,},
+	{PM8606_LED1_GREEN, PM8606_LED1_GREEN, "led0-green", IORESOURCE_IO,},
+	{PM8606_LED1_BLUE,  PM8606_LED1_BLUE,  "led0-blue",  IORESOURCE_IO,},
+	{PM8606_LED2_RED,   PM8606_LED2_RED,   "led1-red",   IORESOURCE_IO,},
+	{PM8606_LED2_GREEN, PM8606_LED2_GREEN, "led1-green", IORESOURCE_IO,},
+	{PM8606_LED2_BLUE,  PM8606_LED2_BLUE,  "led1-blue",  IORESOURCE_IO,},
 };
 
-#define PM8606_LED_RESOURCE(_i, _x)			\
-{							\
-	.name	= pm860x_led_name[_i],			\
-	.start	= PM8606_##_x,				\
-	.end	= PM8606_##_x,				\
-	.flags	= IORESOURCE_IO,			\
-}
-
-static struct resource led_resources[] = {
-	PM8606_LED_RESOURCE(PM8606_LED1_RED, RGB1B),
-	PM8606_LED_RESOURCE(PM8606_LED1_GREEN, RGB1C),
-	PM8606_LED_RESOURCE(PM8606_LED1_BLUE, RGB1D),
-	PM8606_LED_RESOURCE(PM8606_LED2_RED, RGB2B),
-	PM8606_LED_RESOURCE(PM8606_LED2_GREEN, RGB2C),
-	PM8606_LED_RESOURCE(PM8606_LED2_BLUE, RGB2D),
+static struct resource regulator_resources[] __initdata = {
+	{PM8607_ID_BUCK1, PM8607_ID_BUCK1, "buck-1", IORESOURCE_IO,},
+	{PM8607_ID_BUCK2, PM8607_ID_BUCK2, "buck-2", IORESOURCE_IO,},
+	{PM8607_ID_BUCK3, PM8607_ID_BUCK3, "buck-3", IORESOURCE_IO,},
+	{PM8607_ID_LDO1,  PM8607_ID_LDO1,  "ldo-01", IORESOURCE_IO,},
+	{PM8607_ID_LDO2,  PM8607_ID_LDO2,  "ldo-02", IORESOURCE_IO,},
+	{PM8607_ID_LDO3,  PM8607_ID_LDO3,  "ldo-03", IORESOURCE_IO,},
+	{PM8607_ID_LDO4,  PM8607_ID_LDO4,  "ldo-04", IORESOURCE_IO,},
+	{PM8607_ID_LDO5,  PM8607_ID_LDO5,  "ldo-05", IORESOURCE_IO,},
+	{PM8607_ID_LDO6,  PM8607_ID_LDO6,  "ldo-06", IORESOURCE_IO,},
+	{PM8607_ID_LDO7,  PM8607_ID_LDO7,  "ldo-07", IORESOURCE_IO,},
+	{PM8607_ID_LDO8,  PM8607_ID_LDO8,  "ldo-08", IORESOURCE_IO,},
+	{PM8607_ID_LDO9,  PM8607_ID_LDO9,  "ldo-09", IORESOURCE_IO,},
+	{PM8607_ID_LDO10, PM8607_ID_LDO10, "ldo-10", IORESOURCE_IO,},
+	{PM8607_ID_LDO11, PM8607_ID_LDO11, "ldo-11", IORESOURCE_IO,},
+	{PM8607_ID_LDO12, PM8607_ID_LDO12, "ldo-12", IORESOURCE_IO,},
+	{PM8607_ID_LDO13, PM8607_ID_LDO13, "ldo-13", IORESOURCE_IO,},
+	{PM8607_ID_LDO14, PM8607_ID_LDO14, "ldo-14", IORESOURCE_IO,},
+	{PM8607_ID_LDO15, PM8607_ID_LDO15, "ldo-15", IORESOURCE_IO,},
 };
 
-#define PM8606_LED_DEVS(_i)				\
-{							\
-	.name		= "88pm860x-led",		\
-	.num_resources	= 1,				\
-	.resources	= &led_resources[_i],		\
-	.id		= _i,				\
-}
-
-static struct mfd_cell led_devs[] = {
-	PM8606_LED_DEVS(PM8606_LED1_RED),
-	PM8606_LED_DEVS(PM8606_LED1_GREEN),
-	PM8606_LED_DEVS(PM8606_LED1_BLUE),
-	PM8606_LED_DEVS(PM8606_LED2_RED),
-	PM8606_LED_DEVS(PM8606_LED2_GREEN),
-	PM8606_LED_DEVS(PM8606_LED2_BLUE),
+static struct resource touch_resources[] __initdata = {
+	{PM8607_IRQ_PEN, PM8607_IRQ_PEN, "touch", IORESOURCE_IRQ,},
 };
 
-static struct resource touch_resources[] = {
-	{
-		.start	= PM8607_IRQ_PEN,
-		.end	= PM8607_IRQ_PEN,
-		.flags	= IORESOURCE_IRQ,
-	},
+static struct resource onkey_resources[] __initdata = {
+	{PM8607_IRQ_ONKEY, PM8607_IRQ_ONKEY, "onkey", IORESOURCE_IRQ,},
 };
 
-static struct mfd_cell touch_devs[] = {
-	{
-		.name		= "88pm860x-touch",
-		.num_resources	= 1,
-		.resources	= &touch_resources[0],
-	},
+static struct resource codec_resources[] __initdata = {
+	/* Headset microphone insertion or removal */
+	{PM8607_IRQ_MICIN,   PM8607_IRQ_MICIN,   "micin",   IORESOURCE_IRQ,},
+	/* Hook-switch press or release */
+	{PM8607_IRQ_HOOK,    PM8607_IRQ_HOOK,    "hook",    IORESOURCE_IRQ,},
+	/* Headset insertion or removal */
+	{PM8607_IRQ_HEADSET, PM8607_IRQ_HEADSET, "headset", IORESOURCE_IRQ,},
+	/* Audio short */
+	{PM8607_IRQ_AUDIO_SHORT, PM8607_IRQ_AUDIO_SHORT, "audio-short", IORESOURCE_IRQ,},
 };
 
-#define PM8607_REG_RESOURCE(_start, _end)		\
-{							\
-	.start	= PM8607_##_start,			\
-	.end	= PM8607_##_end,			\
-	.flags	= IORESOURCE_IO,			\
-}
+static struct resource battery_resources[] __initdata = {
+	{PM8607_IRQ_CC,  PM8607_IRQ_CC,  "columb counter", IORESOURCE_IRQ,},
+	{PM8607_IRQ_BAT, PM8607_IRQ_BAT, "battery",        IORESOURCE_IRQ,},
+};
 
-static struct resource power_supply_resources[] = {
-	{
-		.name		= "88pm860x-power",
-		.start		= PM8607_IRQ_CHG,
-		.end		= PM8607_IRQ_CHG,
-		.flags		= IORESOURCE_IRQ,
-	},
+static struct resource charger_resources[] __initdata = {
+	{PM8607_IRQ_CHG,  PM8607_IRQ_CHG,  "charger detect",  IORESOURCE_IRQ,},
+	{PM8607_IRQ_CHG_DONE,  PM8607_IRQ_CHG_DONE,  "charging done",       IORESOURCE_IRQ,},
+	{PM8607_IRQ_CHG_FAULT, PM8607_IRQ_CHG_FAULT, "charging timeout",    IORESOURCE_IRQ,},
+	{PM8607_IRQ_GPADC1,    PM8607_IRQ_GPADC1,    "battery temperature", IORESOURCE_IRQ,},
+	{PM8607_IRQ_VBAT, PM8607_IRQ_VBAT, "battery voltage", IORESOURCE_IRQ,},
+	{PM8607_IRQ_VCHG, PM8607_IRQ_VCHG, "vchg voltage",    IORESOURCE_IRQ,},
+};
+
+static struct mfd_cell bk_devs[] __initdata = {
+	{"88pm860x-backlight", 0,},
+	{"88pm860x-backlight", 1,},
+	{"88pm860x-backlight", 2,},
+};
+
+static struct mfd_cell led_devs[] __initdata = {
+	{"88pm860x-led", 0,},
+	{"88pm860x-led", 1,},
+	{"88pm860x-led", 2,},
+	{"88pm860x-led", 3,},
+	{"88pm860x-led", 4,},
+	{"88pm860x-led", 5,},
+};
+
+static struct mfd_cell regulator_devs[] __initdata = {
+	{"88pm860x-regulator", 0,},
+	{"88pm860x-regulator", 1,},
+	{"88pm860x-regulator", 2,},
+	{"88pm860x-regulator", 3,},
+	{"88pm860x-regulator", 4,},
+	{"88pm860x-regulator", 5,},
+	{"88pm860x-regulator", 6,},
+	{"88pm860x-regulator", 7,},
+	{"88pm860x-regulator", 8,},
+	{"88pm860x-regulator", 9,},
+	{"88pm860x-regulator", 10,},
+	{"88pm860x-regulator", 11,},
+	{"88pm860x-regulator", 12,},
+	{"88pm860x-regulator", 13,},
+	{"88pm860x-regulator", 14,},
+	{"88pm860x-regulator", 15,},
+	{"88pm860x-regulator", 16,},
+	{"88pm860x-regulator", 17,},
+};
+
+static struct mfd_cell touch_devs[] __initdata = {
+	{"88pm860x-touch", -1,},
+};
+
+static struct mfd_cell onkey_devs[] __initdata = {
+	{"88pm860x-onkey", -1,},
+};
+
+static struct mfd_cell codec_devs[] __initdata = {
+	{"88pm860x-codec", -1,},
 };
 
 static struct mfd_cell power_devs[] = {
-	{
-		.name		= "88pm860x-power",
-		.num_resources	= 1,
-		.resources	= &power_supply_resources[0],
-		.id		= -1,
-	},
+	{"88pm860x-battery", -1,},
+	{"88pm860x-charger", -1,},
 };
 
-static struct resource onkey_resources[] = {
-	{
-		.name		= "88pm860x-onkey",
-		.start		= PM8607_IRQ_ONKEY,
-		.end		= PM8607_IRQ_ONKEY,
-		.flags		= IORESOURCE_IRQ,
-	},
-};
-
-static struct mfd_cell onkey_devs[] = {
-	{
-		.name		= "88pm860x-onkey",
-		.num_resources	= 1,
-		.resources	= &onkey_resources[0],
-		.id		= -1,
-	},
-};
-
-static struct resource codec_resources[] = {
-	{
-		/* Headset microphone insertion or removal */
-		.name		= "micin",
-		.start		= PM8607_IRQ_MICIN,
-		.end		= PM8607_IRQ_MICIN,
-		.flags		= IORESOURCE_IRQ,
-	}, {
-		/* Hook-switch press or release */
-		.name		= "hook",
-		.start		= PM8607_IRQ_HOOK,
-		.end		= PM8607_IRQ_HOOK,
-		.flags		= IORESOURCE_IRQ,
-	}, {
-		/* Headset insertion or removal */
-		.name		= "headset",
-		.start		= PM8607_IRQ_HEADSET,
-		.end		= PM8607_IRQ_HEADSET,
-		.flags		= IORESOURCE_IRQ,
-	}, {
-		/* Audio short */
-		.name		= "audio-short",
-		.start		= PM8607_IRQ_AUDIO_SHORT,
-		.end		= PM8607_IRQ_AUDIO_SHORT,
-		.flags		= IORESOURCE_IRQ,
-	},
-};
-
-static struct mfd_cell codec_devs[] = {
-	{
-		.name		= "88pm860x-codec",
-		.num_resources	= ARRAY_SIZE(codec_resources),
-		.resources	= &codec_resources[0],
-		.id		= -1,
-	},
-};
-
-static struct resource regulator_resources[] = {
-	PM8607_REG_RESOURCE(BUCK1, BUCK1),
-	PM8607_REG_RESOURCE(BUCK2, BUCK2),
-	PM8607_REG_RESOURCE(BUCK3, BUCK3),
-	PM8607_REG_RESOURCE(LDO1,  LDO1),
-	PM8607_REG_RESOURCE(LDO2,  LDO2),
-	PM8607_REG_RESOURCE(LDO3,  LDO3),
-	PM8607_REG_RESOURCE(LDO4,  LDO4),
-	PM8607_REG_RESOURCE(LDO5,  LDO5),
-	PM8607_REG_RESOURCE(LDO6,  LDO6),
-	PM8607_REG_RESOURCE(LDO7,  LDO7),
-	PM8607_REG_RESOURCE(LDO8,  LDO8),
-	PM8607_REG_RESOURCE(LDO9,  LDO9),
-	PM8607_REG_RESOURCE(LDO10, LDO10),
-	PM8607_REG_RESOURCE(LDO12, LDO12),
-	PM8607_REG_RESOURCE(VIBRATOR_SET, VIBRATOR_SET),
-	PM8607_REG_RESOURCE(LDO14, LDO14),
-};
-
-#define PM8607_REG_DEVS(_id)						\
-{									\
-	.name		= "88pm860x-regulator",				\
-	.num_resources	= 1,						\
-	.resources	= &regulator_resources[PM8607_ID_##_id],	\
-	.id		= PM8607_ID_##_id,				\
-}
-
-static struct mfd_cell regulator_devs[] = {
-	PM8607_REG_DEVS(BUCK1),
-	PM8607_REG_DEVS(BUCK2),
-	PM8607_REG_DEVS(BUCK3),
-	PM8607_REG_DEVS(LDO1),
-	PM8607_REG_DEVS(LDO2),
-	PM8607_REG_DEVS(LDO3),
-	PM8607_REG_DEVS(LDO4),
-	PM8607_REG_DEVS(LDO5),
-	PM8607_REG_DEVS(LDO6),
-	PM8607_REG_DEVS(LDO7),
-	PM8607_REG_DEVS(LDO8),
-	PM8607_REG_DEVS(LDO9),
-	PM8607_REG_DEVS(LDO10),
-	PM8607_REG_DEVS(LDO12),
-	PM8607_REG_DEVS(LDO13),
-	PM8607_REG_DEVS(LDO14),
-};
+static struct pm860x_backlight_pdata bk_pdata[ARRAY_SIZE(bk_devs)];
+static struct pm860x_led_pdata led_pdata[ARRAY_SIZE(led_devs)];
+static struct regulator_init_data regulator_pdata[ARRAY_SIZE(regulator_devs)];
+static struct pm860x_touch_pdata touch_pdata;
+static struct pm860x_power_pdata power_pdata;
 
 struct pm860x_irq_data {
 	int	reg;
@@ -595,37 +503,212 @@
 		free_irq(chip->core_irq, chip);
 }
 
-static void __devinit device_8606_init(struct pm860x_chip *chip,
-				       struct i2c_client *i2c,
-				       struct pm860x_platform_data *pdata)
+static void __devinit device_bk_init(struct pm860x_chip *chip,
+				     struct i2c_client *i2c,
+				     struct pm860x_platform_data *pdata)
+{
+	int ret;
+	int i, j, id;
+
+	if ((pdata == NULL) || (pdata->backlight == NULL))
+		return;
+
+	if (pdata->num_backlights > ARRAY_SIZE(bk_devs))
+		pdata->num_backlights = ARRAY_SIZE(bk_devs);
+
+	for (i = 0; i < pdata->num_backlights; i++) {
+		memcpy(&bk_pdata[i], &pdata->backlight[i],
+			sizeof(struct pm860x_backlight_pdata));
+		bk_devs[i].mfd_data = &bk_pdata[i];
+
+		for (j = 0; j < ARRAY_SIZE(bk_devs); j++) {
+			id = bk_resources[j].start;
+			if (bk_pdata[i].flags != id)
+				continue;
+
+			bk_devs[i].num_resources = 1;
+			bk_devs[i].resources = &bk_resources[j];
+			ret = mfd_add_devices(chip->dev, 0,
+					      &bk_devs[i], 1,
+					      &bk_resources[j], 0);
+			if (ret < 0) {
+				dev_err(chip->dev, "Failed to add "
+					"backlight subdev\n");
+				return;
+			}
+		}
+	}
+}
+
+static void __devinit device_led_init(struct pm860x_chip *chip,
+				      struct i2c_client *i2c,
+				      struct pm860x_platform_data *pdata)
+{
+	int ret;
+	int i, j, id;
+
+	if ((pdata == NULL) || (pdata->led == NULL))
+		return;
+
+	if (pdata->num_leds > ARRAY_SIZE(led_devs))
+		pdata->num_leds = ARRAY_SIZE(led_devs);
+
+	for (i = 0; i < pdata->num_leds; i++) {
+		memcpy(&led_pdata[i], &pdata->led[i],
+			sizeof(struct pm860x_led_pdata));
+		led_devs[i].mfd_data = &led_pdata[i];
+
+		for (j = 0; j < ARRAY_SIZE(led_devs); j++) {
+			id = led_resources[j].start;
+			if (led_pdata[i].flags != id)
+				continue;
+
+			led_devs[i].num_resources = 1;
+			led_devs[i].resources = &led_resources[j],
+			ret = mfd_add_devices(chip->dev, 0,
+					      &led_devs[i], 1,
+					      &led_resources[j], 0);
+			if (ret < 0) {
+				dev_err(chip->dev, "Failed to add "
+					"led subdev\n");
+				return;
+			}
+		}
+	}
+}
+
+static void __devinit device_regulator_init(struct pm860x_chip *chip,
+					    struct i2c_client *i2c,
+					    struct pm860x_platform_data *pdata)
+{
+	struct regulator_init_data *initdata;
+	int ret;
+	int i, j;
+
+	if ((pdata == NULL) || (pdata->regulator == NULL))
+		return;
+
+	if (pdata->num_regulators > ARRAY_SIZE(regulator_devs))
+		pdata->num_regulators = ARRAY_SIZE(regulator_devs);
+
+	for (i = 0, j = -1; i < pdata->num_regulators; i++) {
+		initdata = &pdata->regulator[i];
+		if (strstr(initdata->constraints.name, "BUCK")) {
+			sscanf(initdata->constraints.name, "BUCK%d", &j);
+			/* BUCK1 ~ BUCK3 */
+			if ((j < 1) || (j > 3)) {
+				dev_err(chip->dev, "Failed to add constraint "
+					"(%s)\n", initdata->constraints.name);
+				goto out;
+			}
+			j = (j - 1) + PM8607_ID_BUCK1;
+		}
+		if (strstr(initdata->constraints.name, "LDO")) {
+			sscanf(initdata->constraints.name, "LDO%d", &j);
+			/* LDO1 ~ LDO15 */
+			if ((j < 1) || (j > 15)) {
+				dev_err(chip->dev, "Failed to add constraint "
+					"(%s)\n", initdata->constraints.name);
+				goto out;
+			}
+			j = (j - 1) + PM8607_ID_LDO1;
+		}
+		if (j == -1) {
+			dev_err(chip->dev, "Failed to add constraint (%s)\n",
+				initdata->constraints.name);
+			goto out;
+		}
+		memcpy(&regulator_pdata[i], &pdata->regulator[i],
+			sizeof(struct regulator_init_data));
+		regulator_devs[i].mfd_data = &regulator_pdata[i];
+		regulator_devs[i].num_resources = 1;
+		regulator_devs[i].resources = &regulator_resources[j];
+
+		ret = mfd_add_devices(chip->dev, 0, &regulator_devs[i], 1,
+				      &regulator_resources[j], 0);
+		if (ret < 0) {
+			dev_err(chip->dev, "Failed to add regulator subdev\n");
+			goto out;
+		}
+	}
+out:
+	return;
+}
+
+static void __devinit device_touch_init(struct pm860x_chip *chip,
+					struct i2c_client *i2c,
+					struct pm860x_platform_data *pdata)
 {
 	int ret;
 
-	if (pdata && pdata->backlight) {
-		ret = mfd_add_devices(chip->dev, 0, &backlight_devs[0],
-				      ARRAY_SIZE(backlight_devs),
-				      &backlight_resources[0], 0);
-		if (ret < 0) {
-			dev_err(chip->dev, "Failed to add backlight "
-				"subdev\n");
-			goto out_dev;
-		}
-	}
+	if ((pdata == NULL) || (pdata->touch == NULL))
+		return;
 
-	if (pdata && pdata->led) {
-		ret = mfd_add_devices(chip->dev, 0, &led_devs[0],
-				      ARRAY_SIZE(led_devs),
-				      &led_resources[0], 0);
-		if (ret < 0) {
-			dev_err(chip->dev, "Failed to add led "
-				"subdev\n");
-			goto out_dev;
-		}
-	}
-	return;
-out_dev:
-	mfd_remove_devices(chip->dev);
-	device_irq_exit(chip);
+	memcpy(&touch_pdata, pdata->touch, sizeof(struct pm860x_touch_pdata));
+	touch_devs[0].mfd_data = &touch_pdata;
+	touch_devs[0].num_resources = ARRAY_SIZE(touch_resources);
+	touch_devs[0].resources = &touch_resources[0];
+	ret = mfd_add_devices(chip->dev, 0, &touch_devs[0],
+			      ARRAY_SIZE(touch_devs), &touch_resources[0],
+			      chip->irq_base);
+	if (ret < 0)
+		dev_err(chip->dev, "Failed to add touch subdev\n");
+}
+
+static void __devinit device_power_init(struct pm860x_chip *chip,
+					struct i2c_client *i2c,
+					struct pm860x_platform_data *pdata)
+{
+	int ret;
+
+	if ((pdata == NULL) || (pdata->power == NULL))
+		return;
+
+	memcpy(&power_pdata, pdata->power, sizeof(struct pm860x_power_pdata));
+	power_devs[0].mfd_data = &power_pdata;
+	power_devs[0].num_resources = ARRAY_SIZE(battery_resources);
+	power_devs[0].resources = &battery_resources[0],
+	ret = mfd_add_devices(chip->dev, 0, &power_devs[0], 1,
+			      &battery_resources[0], chip->irq_base);
+	if (ret < 0)
+		dev_err(chip->dev, "Failed to add battery subdev\n");
+
+	power_devs[1].mfd_data = &power_pdata;
+	power_devs[1].num_resources = ARRAY_SIZE(charger_resources);
+	power_devs[1].resources = &charger_resources[0],
+	ret = mfd_add_devices(chip->dev, 0, &power_devs[1], 1,
+			      &charger_resources[0], chip->irq_base);
+	if (ret < 0)
+		dev_err(chip->dev, "Failed to add charger subdev\n");
+}
+
+static void __devinit device_onkey_init(struct pm860x_chip *chip,
+					struct i2c_client *i2c,
+					struct pm860x_platform_data *pdata)
+{
+	int ret;
+
+	onkey_devs[0].num_resources = ARRAY_SIZE(onkey_resources);
+	onkey_devs[0].resources = &onkey_resources[0],
+	ret = mfd_add_devices(chip->dev, 0, &onkey_devs[0],
+			      ARRAY_SIZE(onkey_devs), &onkey_resources[0],
+			      chip->irq_base);
+	if (ret < 0)
+		dev_err(chip->dev, "Failed to add onkey subdev\n");
+}
+
+static void __devinit device_codec_init(struct pm860x_chip *chip,
+					struct i2c_client *i2c,
+					struct pm860x_platform_data *pdata)
+{
+	int ret;
+
+	codec_devs[0].num_resources = ARRAY_SIZE(codec_resources);
+	codec_devs[0].resources = &codec_resources[0],
+	ret = mfd_add_devices(chip->dev, 0, &codec_devs[0],
+			      ARRAY_SIZE(codec_devs), &codec_resources[0], 0);
+	if (ret < 0)
+		dev_err(chip->dev, "Failed to add codec subdev\n");
 }
 
 static void __devinit device_8607_init(struct pm860x_chip *chip,
@@ -683,55 +766,11 @@
 	if (ret < 0)
 		goto out;
 
-	ret = mfd_add_devices(chip->dev, 0, &regulator_devs[0],
-			      ARRAY_SIZE(regulator_devs),
-			      &regulator_resources[0], 0);
-	if (ret < 0) {
-		dev_err(chip->dev, "Failed to add regulator subdev\n");
-		goto out_dev;
-	}
-
-	if (pdata && pdata->touch) {
-		ret = mfd_add_devices(chip->dev, 0, &touch_devs[0],
-				      ARRAY_SIZE(touch_devs),
-				      &touch_resources[0], 0);
-		if (ret < 0) {
-			dev_err(chip->dev, "Failed to add touch "
-				"subdev\n");
-			goto out_dev;
-		}
-	}
-
-	if (pdata && pdata->power) {
-		ret = mfd_add_devices(chip->dev, 0, &power_devs[0],
-				      ARRAY_SIZE(power_devs),
-				      &power_supply_resources[0], 0);
-		if (ret < 0) {
-			dev_err(chip->dev, "Failed to add power supply "
-				"subdev\n");
-			goto out_dev;
-		}
-	}
-
-	ret = mfd_add_devices(chip->dev, 0, &onkey_devs[0],
-			      ARRAY_SIZE(onkey_devs),
-			      &onkey_resources[0], 0);
-	if (ret < 0) {
-		dev_err(chip->dev, "Failed to add onkey subdev\n");
-		goto out_dev;
-	}
-
-	ret = mfd_add_devices(chip->dev, 0, &codec_devs[0],
-			      ARRAY_SIZE(codec_devs),
-			      &codec_resources[0], 0);
-	if (ret < 0) {
-		dev_err(chip->dev, "Failed to add codec subdev\n");
-		goto out_dev;
-	}
-	return;
-out_dev:
-	mfd_remove_devices(chip->dev);
-	device_irq_exit(chip);
+	device_regulator_init(chip, i2c, pdata);
+	device_onkey_init(chip, i2c, pdata);
+	device_touch_init(chip, i2c, pdata);
+	device_power_init(chip, i2c, pdata);
+	device_codec_init(chip, i2c, pdata);
 out:
 	return;
 }
@@ -743,7 +782,8 @@
 
 	switch (chip->id) {
 	case CHIP_PM8606:
-		device_8606_init(chip, chip->client, pdata);
+		device_bk_init(chip, chip->client, pdata);
+		device_led_init(chip, chip->client, pdata);
 		break;
 	case CHIP_PM8607:
 		device_8607_init(chip, chip->client, pdata);
@@ -753,7 +793,8 @@
 	if (chip->companion) {
 		switch (chip->id) {
 		case CHIP_PM8607:
-			device_8606_init(chip, chip->companion, pdata);
+			device_bk_init(chip, chip->companion, pdata);
+			device_led_init(chip, chip->companion, pdata);
 			break;
 		case CHIP_PM8606:
 			device_8607_init(chip, chip->companion, pdata);
diff --git a/drivers/mfd/88pm860x-i2c.c b/drivers/mfd/88pm860x-i2c.c
index bc02e6b..e017dc8 100644
--- a/drivers/mfd/88pm860x-i2c.c
+++ b/drivers/mfd/88pm860x-i2c.c
@@ -126,6 +126,109 @@
 }
 EXPORT_SYMBOL(pm860x_set_bits);
 
+int pm860x_page_reg_read(struct i2c_client *i2c, int reg)
+{
+	struct pm860x_chip *chip = i2c_get_clientdata(i2c);
+	unsigned char zero = 0;
+	unsigned char data;
+	int ret;
+
+	mutex_lock(&chip->io_lock);
+	pm860x_write_device(i2c, 0xFA, 0, &zero);
+	pm860x_write_device(i2c, 0xFB, 0, &zero);
+	pm860x_write_device(i2c, 0xFF, 0, &zero);
+	ret = pm860x_read_device(i2c, reg, 1, &data);
+	if (ret >= 0)
+		ret = (int)data;
+	pm860x_write_device(i2c, 0xFE, 0, &zero);
+	pm860x_write_device(i2c, 0xFC, 0, &zero);
+	mutex_unlock(&chip->io_lock);
+	return ret;
+}
+EXPORT_SYMBOL(pm860x_page_reg_read);
+
+int pm860x_page_reg_write(struct i2c_client *i2c, int reg,
+			  unsigned char data)
+{
+	struct pm860x_chip *chip = i2c_get_clientdata(i2c);
+	unsigned char zero;
+	int ret;
+
+	mutex_lock(&chip->io_lock);
+	pm860x_write_device(i2c, 0xFA, 0, &zero);
+	pm860x_write_device(i2c, 0xFB, 0, &zero);
+	pm860x_write_device(i2c, 0xFF, 0, &zero);
+	ret = pm860x_write_device(i2c, reg, 1, &data);
+	pm860x_write_device(i2c, 0xFE, 0, &zero);
+	pm860x_write_device(i2c, 0xFC, 0, &zero);
+	mutex_unlock(&chip->io_lock);
+	return ret;
+}
+EXPORT_SYMBOL(pm860x_page_reg_write);
+
+int pm860x_page_bulk_read(struct i2c_client *i2c, int reg,
+			  int count, unsigned char *buf)
+{
+	struct pm860x_chip *chip = i2c_get_clientdata(i2c);
+	unsigned char zero = 0;
+	int ret;
+
+	mutex_lock(&chip->io_lock);
+	pm860x_write_device(i2c, 0xFA, 0, &zero);
+	pm860x_write_device(i2c, 0xFB, 0, &zero);
+	pm860x_write_device(i2c, 0xFF, 0, &zero);
+	ret = pm860x_read_device(i2c, reg, count, buf);
+	pm860x_write_device(i2c, 0xFE, 0, &zero);
+	pm860x_write_device(i2c, 0xFC, 0, &zero);
+	mutex_unlock(&chip->io_lock);
+	return ret;
+}
+EXPORT_SYMBOL(pm860x_page_bulk_read);
+
+int pm860x_page_bulk_write(struct i2c_client *i2c, int reg,
+			   int count, unsigned char *buf)
+{
+	struct pm860x_chip *chip = i2c_get_clientdata(i2c);
+	unsigned char zero = 0;
+	int ret;
+
+	mutex_lock(&chip->io_lock);
+	pm860x_write_device(i2c, 0xFA, 0, &zero);
+	pm860x_write_device(i2c, 0xFB, 0, &zero);
+	pm860x_write_device(i2c, 0xFF, 0, &zero);
+	ret = pm860x_write_device(i2c, reg, count, buf);
+	pm860x_write_device(i2c, 0xFE, 0, &zero);
+	pm860x_write_device(i2c, 0xFC, 0, &zero);
+	mutex_unlock(&chip->io_lock);
+	return ret;
+}
+EXPORT_SYMBOL(pm860x_page_bulk_write);
+
+int pm860x_page_set_bits(struct i2c_client *i2c, int reg,
+			 unsigned char mask, unsigned char data)
+{
+	struct pm860x_chip *chip = i2c_get_clientdata(i2c);
+	unsigned char zero;
+	unsigned char value;
+	int ret;
+
+	mutex_lock(&chip->io_lock);
+	pm860x_write_device(i2c, 0xFA, 0, &zero);
+	pm860x_write_device(i2c, 0xFB, 0, &zero);
+	pm860x_write_device(i2c, 0xFF, 0, &zero);
+	ret = pm860x_read_device(i2c, reg, 1, &value);
+	if (ret < 0)
+		goto out;
+	value &= ~mask;
+	value |= data;
+	ret = pm860x_write_device(i2c, reg, 1, &value);
+out:
+	pm860x_write_device(i2c, 0xFE, 0, &zero);
+	pm860x_write_device(i2c, 0xFC, 0, &zero);
+	mutex_unlock(&chip->io_lock);
+	return ret;
+}
+EXPORT_SYMBOL(pm860x_page_set_bits);
 
 static const struct i2c_device_id pm860x_id_table[] = {
 	{ "88PM860x", 0 },
diff --git a/drivers/mfd/Kconfig b/drivers/mfd/Kconfig
index fdca643..8d7d098 100644
--- a/drivers/mfd/Kconfig
+++ b/drivers/mfd/Kconfig
@@ -129,6 +129,17 @@
 	  To compile this driver as a module, choose M here: the
 	  module will be called ucb1400_core.
 
+config TPS6105X
+	tristate "TPS61050/61052 Boost Converters"
+	depends on I2C
+	select REGULATOR
+	select REGULATOR_FIXED_VOLTAGE
+	help
+	  This option enables a driver for the TP61050/TPS61052
+	  high-power "white LED driver". This boost converter is
+	  sometimes used for other things than white LEDs, and
+	  also contains a GPIO pin.
+
 config TPS65010
 	tristate "TPS6501x Power Management chips"
 	depends on I2C && GPIOLIB
@@ -178,6 +189,16 @@
 	  high speed USB OTG transceiver, an audio codec (on most
 	  versions) and many other features.
 
+config TWL4030_MADC
+	tristate "Texas Instruments TWL4030 MADC"
+	depends on TWL4030_CORE
+	help
+	This driver provides support for triton TWL4030-MADC. The
+	driver supports both RT and SW conversion methods.
+
+	This driver can be built as a module. If so it will be
+	named twl4030-madc
+
 config TWL4030_POWER
 	bool "Support power resources on TWL4030 family chips"
 	depends on TWL4030_CORE && ARM
@@ -304,6 +325,18 @@
 	  accessing the device, additional drivers must be enabled in order
 	  to use the functionality of the device.
 
+config MFD_MAX8997
+	bool "Maxim Semiconductor MAX8997/8966 PMIC Support"
+	depends on I2C=y && GENERIC_HARDIRQS
+	select MFD_CORE
+	help
+	  Say yes here to support for Maxim Semiconductor MAX8998/8966.
+	  This is a Power Management IC with RTC, Flash, Fuel Gauge, Haptic,
+	  MUIC controls on chip.
+	  This driver provides common support for accessing the device;
+	  additional drivers must be enabled in order to use the functionality
+	  of the device.
+
 config MFD_MAX8998
 	bool "Maxim Semiconductor MAX8998/National LP3974 PMIC Support"
 	depends on I2C=y && GENERIC_HARDIRQS
@@ -534,6 +567,13 @@
          Select this option if you want debug information using the debug
          filesystem, debugfs.
 
+config AB8500_GPADC
+	bool "AB8500 GPADC driver"
+	depends on AB8500_CORE && REGULATOR_AB8500
+	default y
+	help
+	  AB8500 GPADC driver used to convert Acc and battery/ac/usb voltage
+
 config AB3550_CORE
         bool "ST-Ericsson AB3550 Mixed Signal Circuit core functions"
 	select MFD_CORE
diff --git a/drivers/mfd/Makefile b/drivers/mfd/Makefile
index f0e25ca..47f5709 100644
--- a/drivers/mfd/Makefile
+++ b/drivers/mfd/Makefile
@@ -33,11 +33,13 @@
 obj-$(CONFIG_MFD_WM8350_I2C)	+= wm8350-i2c.o
 obj-$(CONFIG_MFD_WM8994)	+= wm8994-core.o wm8994-irq.o
 
+obj-$(CONFIG_TPS6105X)		+= tps6105x.o
 obj-$(CONFIG_TPS65010)		+= tps65010.o
 obj-$(CONFIG_TPS6507X)		+= tps6507x.o
 obj-$(CONFIG_MENELAUS)		+= menelaus.o
 
 obj-$(CONFIG_TWL4030_CORE)	+= twl-core.o twl4030-irq.o twl6030-irq.o
+obj-$(CONFIG_TWL4030_MADC)      += twl4030-madc.o
 obj-$(CONFIG_TWL4030_POWER)    += twl4030-power.o
 obj-$(CONFIG_TWL4030_CODEC)	+= twl4030-codec.o
 obj-$(CONFIG_TWL6030_PWM)	+= twl6030-pwm.o
@@ -61,6 +63,7 @@
 obj-$(CONFIG_PMIC_DA903X)	+= da903x.o
 max8925-objs			:= max8925-core.o max8925-i2c.o
 obj-$(CONFIG_MFD_MAX8925)	+= max8925.o
+obj-$(CONFIG_MFD_MAX8997)	+= max8997.o
 obj-$(CONFIG_MFD_MAX8998)	+= max8998.o max8998-irq.o
 
 pcf50633-objs			:= pcf50633-core.o pcf50633-irq.o
@@ -71,9 +74,10 @@
 obj-$(CONFIG_AB3100_CORE)	+= ab3100-core.o
 obj-$(CONFIG_AB3100_OTP)	+= ab3100-otp.o
 obj-$(CONFIG_AB3550_CORE)	+= ab3550-core.o
-obj-$(CONFIG_AB8500_CORE)	+= ab8500-core.o
+obj-$(CONFIG_AB8500_CORE)	+= ab8500-core.o ab8500-sysctrl.o
 obj-$(CONFIG_AB8500_I2C_CORE)	+= ab8500-i2c.o
 obj-$(CONFIG_AB8500_DEBUG)	+= ab8500-debugfs.o
+obj-$(CONFIG_AB8500_GPADC)	+= ab8500-gpadc.o
 obj-$(CONFIG_MFD_TIMBERDALE)    += timberdale.o
 obj-$(CONFIG_PMIC_ADP5520)	+= adp5520.o
 obj-$(CONFIG_LPC_SCH)		+= lpc_sch.o
diff --git a/drivers/mfd/ab3100-core.c b/drivers/mfd/ab3100-core.c
index 4193af5..a751927 100644
--- a/drivers/mfd/ab3100-core.c
+++ b/drivers/mfd/ab3100-core.c
@@ -613,7 +613,7 @@
 	ab3100_get_priv.ab3100 = ab3100;
 	ab3100_get_priv.mode = false;
 	ab3100_get_reg_file = debugfs_create_file("get_reg",
-				S_IWUGO, ab3100_dir, &ab3100_get_priv,
+				S_IWUSR, ab3100_dir, &ab3100_get_priv,
 				&ab3100_get_set_reg_fops);
 	if (!ab3100_get_reg_file) {
 		err = -ENOMEM;
@@ -623,7 +623,7 @@
 	ab3100_set_priv.ab3100 = ab3100;
 	ab3100_set_priv.mode = true;
 	ab3100_set_reg_file = debugfs_create_file("set_reg",
-				S_IWUGO, ab3100_dir, &ab3100_set_priv,
+				S_IWUSR, ab3100_dir, &ab3100_set_priv,
 				&ab3100_get_set_reg_fops);
 	if (!ab3100_set_reg_file) {
 		err = -ENOMEM;
@@ -949,10 +949,8 @@
 		goto exit_no_ops;
 
 	/* Set up and register the platform devices. */
-	for (i = 0; i < ARRAY_SIZE(ab3100_devs); i++) {
-		ab3100_devs[i].platform_data = ab3100_plf_data;
-		ab3100_devs[i].data_size = sizeof(struct ab3100_platform_data);
-	}
+	for (i = 0; i < ARRAY_SIZE(ab3100_devs); i++)
+		ab3100_devs[i].mfd_data = ab3100_plf_data;
 
 	err = mfd_add_devices(&client->dev, 0, ab3100_devs,
 		ARRAY_SIZE(ab3100_devs), NULL, 0);
diff --git a/drivers/mfd/ab3550-core.c b/drivers/mfd/ab3550-core.c
index 5fbca34..c12d042 100644
--- a/drivers/mfd/ab3550-core.c
+++ b/drivers/mfd/ab3550-core.c
@@ -1053,17 +1053,17 @@
 		goto exit_destroy_dir;
 
 	ab3550_bank_file = debugfs_create_file("register-bank",
-		(S_IRUGO | S_IWUGO), ab3550_dir, ab, &ab3550_bank_fops);
+		(S_IRUGO | S_IWUSR), ab3550_dir, ab, &ab3550_bank_fops);
 	if (!ab3550_bank_file)
 		goto exit_destroy_reg;
 
 	ab3550_address_file = debugfs_create_file("register-address",
-		(S_IRUGO | S_IWUGO), ab3550_dir, ab, &ab3550_address_fops);
+		(S_IRUGO | S_IWUSR), ab3550_dir, ab, &ab3550_address_fops);
 	if (!ab3550_address_file)
 		goto exit_destroy_bank;
 
 	ab3550_val_file = debugfs_create_file("register-value",
-		(S_IRUGO | S_IWUGO), ab3550_dir, ab, &ab3550_val_fops);
+		(S_IRUGO | S_IWUSR), ab3550_dir, ab, &ab3550_val_fops);
 	if (!ab3550_val_file)
 		goto exit_destroy_address;
 
@@ -1320,10 +1320,8 @@
 		goto exit_no_ops;
 
 	/* Set up and register the platform devices. */
-	for (i = 0; i < AB3550_NUM_DEVICES; i++) {
-		ab3550_devs[i].platform_data = ab3550_plf_data->dev_data[i];
-		ab3550_devs[i].data_size = ab3550_plf_data->dev_data_sz[i];
-	}
+	for (i = 0; i < AB3550_NUM_DEVICES; i++)
+		ab3550_devs[i].mfd_data = ab3550_plf_data->dev_data[i];
 
 	err = mfd_add_devices(&client->dev, 0, ab3550_devs,
 		ARRAY_SIZE(ab3550_devs), NULL,
diff --git a/drivers/mfd/ab8500-core.c b/drivers/mfd/ab8500-core.c
index b688701..6e185b2 100644
--- a/drivers/mfd/ab8500-core.c
+++ b/drivers/mfd/ab8500-core.c
@@ -4,7 +4,7 @@
  * License Terms: GNU General Public License v2
  * Author: Srinidhi Kasagar <srinidhi.kasagar@stericsson.com>
  * Author: Rabin Vincent <rabin.vincent@stericsson.com>
- * Changes: Mattias Wallin <mattias.wallin@stericsson.com>
+ * Author: Mattias Wallin <mattias.wallin@stericsson.com>
  */
 
 #include <linux/kernel.h>
@@ -90,6 +90,7 @@
 #define AB8500_IT_MASK24_REG		0x57
 
 #define AB8500_REV_REG			0x80
+#define AB8500_SWITCH_OFF_STATUS	0x00
 
 /*
  * Map interrupt numbers to the LATCH and MASK register offsets, Interrupt
@@ -652,10 +653,38 @@
 	return sprintf(buf, "%#x\n", ab8500 ? ab8500->chip_id : -EINVAL);
 }
 
+/*
+ * ab8500 has switched off due to (SWITCH_OFF_STATUS):
+ * 0x01 Swoff bit programming
+ * 0x02 Thermal protection activation
+ * 0x04 Vbat lower then BattOk falling threshold
+ * 0x08 Watchdog expired
+ * 0x10 Non presence of 32kHz clock
+ * 0x20 Battery level lower than power on reset threshold
+ * 0x40 Power on key 1 pressed longer than 10 seconds
+ * 0x80 DB8500 thermal shutdown
+ */
+static ssize_t show_switch_off_status(struct device *dev,
+				struct device_attribute *attr, char *buf)
+{
+	int ret;
+	u8 value;
+	struct ab8500 *ab8500;
+
+	ab8500 = dev_get_drvdata(dev);
+	ret = get_register_interruptible(ab8500, AB8500_RTC,
+		AB8500_SWITCH_OFF_STATUS, &value);
+	if (ret < 0)
+		return ret;
+	return sprintf(buf, "%#x\n", value);
+}
+
 static DEVICE_ATTR(chip_id, S_IRUGO, show_chip_id, NULL);
+static DEVICE_ATTR(switch_off_status, S_IRUGO, show_switch_off_status, NULL);
 
 static struct attribute *ab8500_sysfs_entries[] = {
 	&dev_attr_chip_id.attr,
+	&dev_attr_switch_off_status.attr,
 	NULL,
 };
 
@@ -686,9 +715,10 @@
 	 * 0x10 - Cut 1.0
 	 * 0x11 - Cut 1.1
 	 * 0x20 - Cut 2.0
+	 * 0x30 - Cut 3.0
 	 */
-	if (value == 0x0 || value == 0x10 || value == 0x11 || value == 0x20) {
-		ab8500->revision = value;
+	if (value == 0x0 || value == 0x10 || value == 0x11 || value == 0x20 ||
+		value == 0x30) {
 		dev_info(ab8500->dev, "detected chip, revision: %#x\n", value);
 	} else {
 		dev_err(ab8500->dev, "unknown chip, revision: %#x\n", value);
@@ -696,6 +726,24 @@
 	}
 	ab8500->chip_id = value;
 
+	/*
+	 * ab8500 has switched off due to (SWITCH_OFF_STATUS):
+	 * 0x01 Swoff bit programming
+	 * 0x02 Thermal protection activation
+	 * 0x04 Vbat lower then BattOk falling threshold
+	 * 0x08 Watchdog expired
+	 * 0x10 Non presence of 32kHz clock
+	 * 0x20 Battery level lower than power on reset threshold
+	 * 0x40 Power on key 1 pressed longer than 10 seconds
+	 * 0x80 DB8500 thermal shutdown
+	 */
+
+	ret = get_register_interruptible(ab8500, AB8500_RTC,
+		AB8500_SWITCH_OFF_STATUS, &value);
+	if (ret < 0)
+		return ret;
+	dev_info(ab8500->dev, "switch off status: %#x", value);
+
 	if (plat && plat->init)
 		plat->init(ab8500);
 
@@ -764,6 +812,6 @@
 	return 0;
 }
 
-MODULE_AUTHOR("Srinidhi Kasagar, Rabin Vincent");
+MODULE_AUTHOR("Mattias Wallin, Srinidhi Kasagar, Rabin Vincent");
 MODULE_DESCRIPTION("AB8500 MFD core");
 MODULE_LICENSE("GPL v2");
diff --git a/drivers/mfd/ab8500-debugfs.c b/drivers/mfd/ab8500-debugfs.c
index 3c1541a..64748e4 100644
--- a/drivers/mfd/ab8500-debugfs.c
+++ b/drivers/mfd/ab8500-debugfs.c
@@ -585,18 +585,18 @@
 		goto exit_destroy_dir;
 
 	ab8500_bank_file = debugfs_create_file("register-bank",
-		(S_IRUGO | S_IWUGO), ab8500_dir, &plf->dev, &ab8500_bank_fops);
+		(S_IRUGO | S_IWUSR), ab8500_dir, &plf->dev, &ab8500_bank_fops);
 	if (!ab8500_bank_file)
 		goto exit_destroy_reg;
 
 	ab8500_address_file = debugfs_create_file("register-address",
-		(S_IRUGO | S_IWUGO), ab8500_dir, &plf->dev,
+		(S_IRUGO | S_IWUSR), ab8500_dir, &plf->dev,
 		&ab8500_address_fops);
 	if (!ab8500_address_file)
 		goto exit_destroy_bank;
 
 	ab8500_val_file = debugfs_create_file("register-value",
-		(S_IRUGO | S_IWUGO), ab8500_dir, &plf->dev, &ab8500_val_fops);
+		(S_IRUGO | S_IWUSR), ab8500_dir, &plf->dev, &ab8500_val_fops);
 	if (!ab8500_val_file)
 		goto exit_destroy_address;
 
diff --git a/drivers/mfd/ab8500-gpadc.c b/drivers/mfd/ab8500-gpadc.c
new file mode 100644
index 0000000..bc93b2e
--- /dev/null
+++ b/drivers/mfd/ab8500-gpadc.c
@@ -0,0 +1,614 @@
+/*
+ * Copyright (C) ST-Ericsson SA 2010
+ *
+ * License Terms: GNU General Public License v2
+ * Author: Arun R Murthy <arun.murthy@stericsson.com>
+ * Author: Daniel Willerud <daniel.willerud@stericsson.com>
+ * Author: Johan Palsson <johan.palsson@stericsson.com>
+ */
+#include <linux/init.h>
+#include <linux/module.h>
+#include <linux/device.h>
+#include <linux/interrupt.h>
+#include <linux/spinlock.h>
+#include <linux/delay.h>
+#include <linux/platform_device.h>
+#include <linux/completion.h>
+#include <linux/regulator/consumer.h>
+#include <linux/err.h>
+#include <linux/slab.h>
+#include <linux/list.h>
+#include <linux/mfd/ab8500.h>
+#include <linux/mfd/abx500.h>
+#include <linux/mfd/ab8500/gpadc.h>
+
+/*
+ * GPADC register offsets
+ * Bank : 0x0A
+ */
+#define AB8500_GPADC_CTRL1_REG		0x00
+#define AB8500_GPADC_CTRL2_REG		0x01
+#define AB8500_GPADC_CTRL3_REG		0x02
+#define AB8500_GPADC_AUTO_TIMER_REG	0x03
+#define AB8500_GPADC_STAT_REG		0x04
+#define AB8500_GPADC_MANDATAL_REG	0x05
+#define AB8500_GPADC_MANDATAH_REG	0x06
+#define AB8500_GPADC_AUTODATAL_REG	0x07
+#define AB8500_GPADC_AUTODATAH_REG	0x08
+#define AB8500_GPADC_MUX_CTRL_REG	0x09
+
+/*
+ * OTP register offsets
+ * Bank : 0x15
+ */
+#define AB8500_GPADC_CAL_1		0x0F
+#define AB8500_GPADC_CAL_2		0x10
+#define AB8500_GPADC_CAL_3		0x11
+#define AB8500_GPADC_CAL_4		0x12
+#define AB8500_GPADC_CAL_5		0x13
+#define AB8500_GPADC_CAL_6		0x14
+#define AB8500_GPADC_CAL_7		0x15
+
+/* gpadc constants */
+#define EN_VINTCORE12			0x04
+#define EN_VTVOUT			0x02
+#define EN_GPADC			0x01
+#define DIS_GPADC			0x00
+#define SW_AVG_16			0x60
+#define ADC_SW_CONV			0x04
+#define EN_ICHAR			0x80
+#define EN_BUF				0x40
+#define DIS_ZERO			0x00
+#define GPADC_BUSY			0x01
+
+/* GPADC constants from AB8500 spec, UM0836 */
+#define ADC_RESOLUTION			1024
+#define ADC_CH_BTEMP_MIN		0
+#define ADC_CH_BTEMP_MAX		1350
+#define ADC_CH_DIETEMP_MIN		0
+#define ADC_CH_DIETEMP_MAX		1350
+#define ADC_CH_CHG_V_MIN		0
+#define ADC_CH_CHG_V_MAX		20030
+#define ADC_CH_ACCDET2_MIN		0
+#define ADC_CH_ACCDET2_MAX		2500
+#define ADC_CH_VBAT_MIN			2300
+#define ADC_CH_VBAT_MAX			4800
+#define ADC_CH_CHG_I_MIN		0
+#define ADC_CH_CHG_I_MAX		1500
+#define ADC_CH_BKBAT_MIN		0
+#define ADC_CH_BKBAT_MAX		3200
+
+/* This is used to not lose precision when dividing to get gain and offset */
+#define CALIB_SCALE			1000
+
+enum cal_channels {
+	ADC_INPUT_VMAIN = 0,
+	ADC_INPUT_BTEMP,
+	ADC_INPUT_VBAT,
+	NBR_CAL_INPUTS,
+};
+
+/**
+ * struct adc_cal_data - Table for storing gain and offset for the calibrated
+ * ADC channels
+ * @gain:		Gain of the ADC channel
+ * @offset:		Offset of the ADC channel
+ */
+struct adc_cal_data {
+	u64 gain;
+	u64 offset;
+};
+
+/**
+ * struct ab8500_gpadc - AB8500 GPADC device information
+ * @dev:			pointer to the struct device
+ * @node:			a list of AB8500 GPADCs, hence prepared for
+				reentrance
+ * @ab8500_gpadc_complete:	pointer to the struct completion, to indicate
+ *				the completion of gpadc conversion
+ * @ab8500_gpadc_lock:		structure of type mutex
+ * @regu:			pointer to the struct regulator
+ * @irq:			interrupt number that is used by gpadc
+ * @cal_data			array of ADC calibration data structs
+ */
+struct ab8500_gpadc {
+	struct device *dev;
+	struct list_head node;
+	struct completion ab8500_gpadc_complete;
+	struct mutex ab8500_gpadc_lock;
+	struct regulator *regu;
+	int irq;
+	struct adc_cal_data cal_data[NBR_CAL_INPUTS];
+};
+
+static LIST_HEAD(ab8500_gpadc_list);
+
+/**
+ * ab8500_gpadc_get() - returns a reference to the primary AB8500 GPADC
+ * (i.e. the first GPADC in the instance list)
+ */
+struct ab8500_gpadc *ab8500_gpadc_get(char *name)
+{
+	struct ab8500_gpadc *gpadc;
+
+	list_for_each_entry(gpadc, &ab8500_gpadc_list, node) {
+		if (!strcmp(name, dev_name(gpadc->dev)))
+		    return gpadc;
+	}
+
+	return ERR_PTR(-ENOENT);
+}
+EXPORT_SYMBOL(ab8500_gpadc_get);
+
+static int ab8500_gpadc_ad_to_voltage(struct ab8500_gpadc *gpadc, u8 input,
+	int ad_value)
+{
+	int res;
+
+	switch (input) {
+	case MAIN_CHARGER_V:
+		/* For some reason we don't have calibrated data */
+		if (!gpadc->cal_data[ADC_INPUT_VMAIN].gain) {
+			res = ADC_CH_CHG_V_MIN + (ADC_CH_CHG_V_MAX -
+				ADC_CH_CHG_V_MIN) * ad_value /
+				ADC_RESOLUTION;
+			break;
+		}
+		/* Here we can use the calibrated data */
+		res = (int) (ad_value * gpadc->cal_data[ADC_INPUT_VMAIN].gain +
+			gpadc->cal_data[ADC_INPUT_VMAIN].offset) / CALIB_SCALE;
+		break;
+
+	case BAT_CTRL:
+	case BTEMP_BALL:
+	case ACC_DETECT1:
+	case ADC_AUX1:
+	case ADC_AUX2:
+		/* For some reason we don't have calibrated data */
+		if (!gpadc->cal_data[ADC_INPUT_BTEMP].gain) {
+			res = ADC_CH_BTEMP_MIN + (ADC_CH_BTEMP_MAX -
+				ADC_CH_BTEMP_MIN) * ad_value /
+				ADC_RESOLUTION;
+			break;
+		}
+		/* Here we can use the calibrated data */
+		res = (int) (ad_value * gpadc->cal_data[ADC_INPUT_BTEMP].gain +
+			gpadc->cal_data[ADC_INPUT_BTEMP].offset) / CALIB_SCALE;
+		break;
+
+	case MAIN_BAT_V:
+		/* For some reason we don't have calibrated data */
+		if (!gpadc->cal_data[ADC_INPUT_VBAT].gain) {
+			res = ADC_CH_VBAT_MIN + (ADC_CH_VBAT_MAX -
+				ADC_CH_VBAT_MIN) * ad_value /
+				ADC_RESOLUTION;
+			break;
+		}
+		/* Here we can use the calibrated data */
+		res = (int) (ad_value * gpadc->cal_data[ADC_INPUT_VBAT].gain +
+			gpadc->cal_data[ADC_INPUT_VBAT].offset) / CALIB_SCALE;
+		break;
+
+	case DIE_TEMP:
+		res = ADC_CH_DIETEMP_MIN +
+			(ADC_CH_DIETEMP_MAX - ADC_CH_DIETEMP_MIN) * ad_value /
+			ADC_RESOLUTION;
+		break;
+
+	case ACC_DETECT2:
+		res = ADC_CH_ACCDET2_MIN +
+			(ADC_CH_ACCDET2_MAX - ADC_CH_ACCDET2_MIN) * ad_value /
+			ADC_RESOLUTION;
+		break;
+
+	case VBUS_V:
+		res = ADC_CH_CHG_V_MIN +
+			(ADC_CH_CHG_V_MAX - ADC_CH_CHG_V_MIN) * ad_value /
+			ADC_RESOLUTION;
+		break;
+
+	case MAIN_CHARGER_C:
+	case USB_CHARGER_C:
+		res = ADC_CH_CHG_I_MIN +
+			(ADC_CH_CHG_I_MAX - ADC_CH_CHG_I_MIN) * ad_value /
+			ADC_RESOLUTION;
+		break;
+
+	case BK_BAT_V:
+		res = ADC_CH_BKBAT_MIN +
+			(ADC_CH_BKBAT_MAX - ADC_CH_BKBAT_MIN) * ad_value /
+			ADC_RESOLUTION;
+		break;
+
+	default:
+		dev_err(gpadc->dev,
+			"unknown channel, not possible to convert\n");
+		res = -EINVAL;
+		break;
+
+	}
+	return res;
+}
+
+/**
+ * ab8500_gpadc_convert() - gpadc conversion
+ * @input:	analog input to be converted to digital data
+ *
+ * This function converts the selected analog i/p to digital
+ * data.
+ */
+int ab8500_gpadc_convert(struct ab8500_gpadc *gpadc, u8 input)
+{
+	int ret;
+	u16 data = 0;
+	int looplimit = 0;
+	u8 val, low_data, high_data;
+
+	if (!gpadc)
+		return -ENODEV;
+
+	mutex_lock(&gpadc->ab8500_gpadc_lock);
+	/* Enable VTVout LDO this is required for GPADC */
+	regulator_enable(gpadc->regu);
+
+	/* Check if ADC is not busy, lock and proceed */
+	do {
+		ret = abx500_get_register_interruptible(gpadc->dev,
+			AB8500_GPADC, AB8500_GPADC_STAT_REG, &val);
+		if (ret < 0)
+			goto out;
+		if (!(val & GPADC_BUSY))
+			break;
+		msleep(10);
+	} while (++looplimit < 10);
+	if (looplimit >= 10 && (val & GPADC_BUSY)) {
+		dev_err(gpadc->dev, "gpadc_conversion: GPADC busy");
+		ret = -EINVAL;
+		goto out;
+	}
+
+	/* Enable GPADC */
+	ret = abx500_mask_and_set_register_interruptible(gpadc->dev,
+		AB8500_GPADC, AB8500_GPADC_CTRL1_REG, EN_GPADC, EN_GPADC);
+	if (ret < 0) {
+		dev_err(gpadc->dev, "gpadc_conversion: enable gpadc failed\n");
+		goto out;
+	}
+	/* Select the input source and set average samples to 16 */
+	ret = abx500_set_register_interruptible(gpadc->dev, AB8500_GPADC,
+		AB8500_GPADC_CTRL2_REG, (input | SW_AVG_16));
+	if (ret < 0) {
+		dev_err(gpadc->dev,
+			"gpadc_conversion: set avg samples failed\n");
+		goto out;
+	}
+	/*
+	 * Enable ADC, buffering, select rising edge and enable ADC path
+	 * charging current sense if it needed
+	 */
+	switch (input) {
+	case MAIN_CHARGER_C:
+	case USB_CHARGER_C:
+		ret = abx500_mask_and_set_register_interruptible(gpadc->dev,
+			AB8500_GPADC, AB8500_GPADC_CTRL1_REG,
+			EN_BUF | EN_ICHAR,
+			EN_BUF | EN_ICHAR);
+		break;
+	default:
+		ret = abx500_mask_and_set_register_interruptible(gpadc->dev,
+			AB8500_GPADC, AB8500_GPADC_CTRL1_REG, EN_BUF, EN_BUF);
+		break;
+	}
+	if (ret < 0) {
+		dev_err(gpadc->dev,
+			"gpadc_conversion: select falling edge failed\n");
+		goto out;
+	}
+	ret = abx500_mask_and_set_register_interruptible(gpadc->dev,
+		AB8500_GPADC, AB8500_GPADC_CTRL1_REG, ADC_SW_CONV, ADC_SW_CONV);
+	if (ret < 0) {
+		dev_err(gpadc->dev,
+			"gpadc_conversion: start s/w conversion failed\n");
+		goto out;
+	}
+	/* wait for completion of conversion */
+	if (!wait_for_completion_timeout(&gpadc->ab8500_gpadc_complete, 2*HZ)) {
+		dev_err(gpadc->dev,
+			"timeout: didnt recieve GPADC conversion interrupt\n");
+		ret = -EINVAL;
+		goto out;
+	}
+
+	/* Read the converted RAW data */
+	ret = abx500_get_register_interruptible(gpadc->dev, AB8500_GPADC,
+		AB8500_GPADC_MANDATAL_REG, &low_data);
+	if (ret < 0) {
+		dev_err(gpadc->dev, "gpadc_conversion: read low data failed\n");
+		goto out;
+	}
+
+	ret = abx500_get_register_interruptible(gpadc->dev, AB8500_GPADC,
+		AB8500_GPADC_MANDATAH_REG, &high_data);
+	if (ret < 0) {
+		dev_err(gpadc->dev,
+			"gpadc_conversion: read high data failed\n");
+		goto out;
+	}
+
+	data = (high_data << 8) | low_data;
+	/* Disable GPADC */
+	ret = abx500_set_register_interruptible(gpadc->dev, AB8500_GPADC,
+		AB8500_GPADC_CTRL1_REG, DIS_GPADC);
+	if (ret < 0) {
+		dev_err(gpadc->dev, "gpadc_conversion: disable gpadc failed\n");
+		goto out;
+	}
+	/* Disable VTVout LDO this is required for GPADC */
+	regulator_disable(gpadc->regu);
+	mutex_unlock(&gpadc->ab8500_gpadc_lock);
+	ret = ab8500_gpadc_ad_to_voltage(gpadc, input, data);
+	return ret;
+
+out:
+	/*
+	 * It has shown to be needed to turn off the GPADC if an error occurs,
+	 * otherwise we might have problem when waiting for the busy bit in the
+	 * GPADC status register to go low. In V1.1 there wait_for_completion
+	 * seems to timeout when waiting for an interrupt.. Not seen in V2.0
+	 */
+	(void) abx500_set_register_interruptible(gpadc->dev, AB8500_GPADC,
+		AB8500_GPADC_CTRL1_REG, DIS_GPADC);
+	regulator_disable(gpadc->regu);
+	mutex_unlock(&gpadc->ab8500_gpadc_lock);
+	dev_err(gpadc->dev,
+		"gpadc_conversion: Failed to AD convert channel %d\n", input);
+	return ret;
+}
+EXPORT_SYMBOL(ab8500_gpadc_convert);
+
+/**
+ * ab8500_bm_gpswadcconvend_handler() - isr for s/w gpadc conversion completion
+ * @irq:	irq number
+ * @data:	pointer to the data passed during request irq
+ *
+ * This is a interrupt service routine for s/w gpadc conversion completion.
+ * Notifies the gpadc completion is completed and the converted raw value
+ * can be read from the registers.
+ * Returns IRQ status(IRQ_HANDLED)
+ */
+static irqreturn_t ab8500_bm_gpswadcconvend_handler(int irq, void *_gpadc)
+{
+	struct ab8500_gpadc *gpadc = _gpadc;
+
+	complete(&gpadc->ab8500_gpadc_complete);
+
+	return IRQ_HANDLED;
+}
+
+static int otp_cal_regs[] = {
+	AB8500_GPADC_CAL_1,
+	AB8500_GPADC_CAL_2,
+	AB8500_GPADC_CAL_3,
+	AB8500_GPADC_CAL_4,
+	AB8500_GPADC_CAL_5,
+	AB8500_GPADC_CAL_6,
+	AB8500_GPADC_CAL_7,
+};
+
+static void ab8500_gpadc_read_calibration_data(struct ab8500_gpadc *gpadc)
+{
+	int i;
+	int ret[ARRAY_SIZE(otp_cal_regs)];
+	u8 gpadc_cal[ARRAY_SIZE(otp_cal_regs)];
+
+	int vmain_high, vmain_low;
+	int btemp_high, btemp_low;
+	int vbat_high, vbat_low;
+
+	/* First we read all OTP registers and store the error code */
+	for (i = 0; i < ARRAY_SIZE(otp_cal_regs); i++) {
+		ret[i] = abx500_get_register_interruptible(gpadc->dev,
+			AB8500_OTP_EMUL, otp_cal_regs[i],  &gpadc_cal[i]);
+		if (ret[i] < 0)
+			dev_err(gpadc->dev, "%s: read otp reg 0x%02x failed\n",
+				__func__, otp_cal_regs[i]);
+	}
+
+	/*
+	 * The ADC calibration data is stored in OTP registers.
+	 * The layout of the calibration data is outlined below and a more
+	 * detailed description can be found in UM0836
+	 *
+	 * vm_h/l = vmain_high/low
+	 * bt_h/l = btemp_high/low
+	 * vb_h/l = vbat_high/low
+	 *
+	 * Data bits:
+	 * | 7	   | 6	   | 5	   | 4	   | 3	   | 2	   | 1	   | 0
+	 * |.......|.......|.......|.......|.......|.......|.......|.......
+	 * |						   | vm_h9 | vm_h8
+	 * |.......|.......|.......|.......|.......|.......|.......|.......
+	 * |		   | vm_h7 | vm_h6 | vm_h5 | vm_h4 | vm_h3 | vm_h2
+	 * |.......|.......|.......|.......|.......|.......|.......|.......
+	 * | vm_h1 | vm_h0 | vm_l4 | vm_l3 | vm_l2 | vm_l1 | vm_l0 | bt_h9
+	 * |.......|.......|.......|.......|.......|.......|.......|.......
+	 * | bt_h8 | bt_h7 | bt_h6 | bt_h5 | bt_h4 | bt_h3 | bt_h2 | bt_h1
+	 * |.......|.......|.......|.......|.......|.......|.......|.......
+	 * | bt_h0 | bt_l4 | bt_l3 | bt_l2 | bt_l1 | bt_l0 | vb_h9 | vb_h8
+	 * |.......|.......|.......|.......|.......|.......|.......|.......
+	 * | vb_h7 | vb_h6 | vb_h5 | vb_h4 | vb_h3 | vb_h2 | vb_h1 | vb_h0
+	 * |.......|.......|.......|.......|.......|.......|.......|.......
+	 * | vb_l5 | vb_l4 | vb_l3 | vb_l2 | vb_l1 | vb_l0 |
+	 * |.......|.......|.......|.......|.......|.......|.......|.......
+	 *
+	 *
+	 * Ideal output ADC codes corresponding to injected input voltages
+	 * during manufacturing is:
+	 *
+	 * vmain_high: Vin = 19500mV / ADC ideal code = 997
+	 * vmain_low:  Vin = 315mV   / ADC ideal code = 16
+	 * btemp_high: Vin = 1300mV  / ADC ideal code = 985
+	 * btemp_low:  Vin = 21mV    / ADC ideal code = 16
+	 * vbat_high:  Vin = 4700mV  / ADC ideal code = 982
+	 * vbat_low:   Vin = 2380mV  / ADC ideal code = 33
+	 */
+
+	/* Calculate gain and offset for VMAIN if all reads succeeded */
+	if (!(ret[0] < 0 || ret[1] < 0 || ret[2] < 0)) {
+		vmain_high = (((gpadc_cal[0] & 0x03) << 8) |
+			((gpadc_cal[1] & 0x3F) << 2) |
+			((gpadc_cal[2] & 0xC0) >> 6));
+
+		vmain_low = ((gpadc_cal[2] & 0x3E) >> 1);
+
+		gpadc->cal_data[ADC_INPUT_VMAIN].gain = CALIB_SCALE *
+			(19500 - 315) /	(vmain_high - vmain_low);
+
+		gpadc->cal_data[ADC_INPUT_VMAIN].offset = CALIB_SCALE * 19500 -
+			(CALIB_SCALE * (19500 - 315) /
+			 (vmain_high - vmain_low)) * vmain_high;
+	} else {
+		gpadc->cal_data[ADC_INPUT_VMAIN].gain = 0;
+	}
+
+	/* Calculate gain and offset for BTEMP if all reads succeeded */
+	if (!(ret[2] < 0 || ret[3] < 0 || ret[4] < 0)) {
+		btemp_high = (((gpadc_cal[2] & 0x01) << 9) |
+			(gpadc_cal[3] << 1) |
+			((gpadc_cal[4] & 0x80) >> 7));
+
+		btemp_low = ((gpadc_cal[4] & 0x7C) >> 2);
+
+		gpadc->cal_data[ADC_INPUT_BTEMP].gain =
+			CALIB_SCALE * (1300 - 21) / (btemp_high - btemp_low);
+
+		gpadc->cal_data[ADC_INPUT_BTEMP].offset = CALIB_SCALE * 1300 -
+			(CALIB_SCALE * (1300 - 21) /
+			(btemp_high - btemp_low)) * btemp_high;
+	} else {
+		gpadc->cal_data[ADC_INPUT_BTEMP].gain = 0;
+	}
+
+	/* Calculate gain and offset for VBAT if all reads succeeded */
+	if (!(ret[4] < 0 || ret[5] < 0 || ret[6] < 0)) {
+		vbat_high = (((gpadc_cal[4] & 0x03) << 8) | gpadc_cal[5]);
+		vbat_low = ((gpadc_cal[6] & 0xFC) >> 2);
+
+		gpadc->cal_data[ADC_INPUT_VBAT].gain = CALIB_SCALE *
+			(4700 - 2380) /	(vbat_high - vbat_low);
+
+		gpadc->cal_data[ADC_INPUT_VBAT].offset = CALIB_SCALE * 4700 -
+			(CALIB_SCALE * (4700 - 2380) /
+			(vbat_high - vbat_low)) * vbat_high;
+	} else {
+		gpadc->cal_data[ADC_INPUT_VBAT].gain = 0;
+	}
+
+	dev_dbg(gpadc->dev, "VMAIN gain %llu offset %llu\n",
+		gpadc->cal_data[ADC_INPUT_VMAIN].gain,
+		gpadc->cal_data[ADC_INPUT_VMAIN].offset);
+
+	dev_dbg(gpadc->dev, "BTEMP gain %llu offset %llu\n",
+		gpadc->cal_data[ADC_INPUT_BTEMP].gain,
+		gpadc->cal_data[ADC_INPUT_BTEMP].offset);
+
+	dev_dbg(gpadc->dev, "VBAT gain %llu offset %llu\n",
+		gpadc->cal_data[ADC_INPUT_VBAT].gain,
+		gpadc->cal_data[ADC_INPUT_VBAT].offset);
+}
+
+static int __devinit ab8500_gpadc_probe(struct platform_device *pdev)
+{
+	int ret = 0;
+	struct ab8500_gpadc *gpadc;
+
+	gpadc = kzalloc(sizeof(struct ab8500_gpadc), GFP_KERNEL);
+	if (!gpadc) {
+		dev_err(&pdev->dev, "Error: No memory\n");
+		return -ENOMEM;
+	}
+
+	gpadc->irq = platform_get_irq_byname(pdev, "SW_CONV_END");
+	if (gpadc->irq < 0) {
+		dev_err(gpadc->dev, "failed to get platform irq-%d\n",
+			gpadc->irq);
+		ret = gpadc->irq;
+		goto fail;
+	}
+
+	gpadc->dev = &pdev->dev;
+	mutex_init(&gpadc->ab8500_gpadc_lock);
+
+	/* Initialize completion used to notify completion of conversion */
+	init_completion(&gpadc->ab8500_gpadc_complete);
+
+	/* Register interrupt  - SwAdcComplete */
+	ret = request_threaded_irq(gpadc->irq, NULL,
+		ab8500_bm_gpswadcconvend_handler,
+		IRQF_NO_SUSPEND | IRQF_SHARED, "ab8500-gpadc", gpadc);
+	if (ret < 0) {
+		dev_err(gpadc->dev, "Failed to register interrupt, irq: %d\n",
+			gpadc->irq);
+		goto fail;
+	}
+
+	/* VTVout LDO used to power up ab8500-GPADC */
+	gpadc->regu = regulator_get(&pdev->dev, "vddadc");
+	if (IS_ERR(gpadc->regu)) {
+		ret = PTR_ERR(gpadc->regu);
+		dev_err(gpadc->dev, "failed to get vtvout LDO\n");
+		goto fail_irq;
+	}
+	ab8500_gpadc_read_calibration_data(gpadc);
+	list_add_tail(&gpadc->node, &ab8500_gpadc_list);
+	dev_dbg(gpadc->dev, "probe success\n");
+	return 0;
+fail_irq:
+	free_irq(gpadc->irq, gpadc);
+fail:
+	kfree(gpadc);
+	gpadc = NULL;
+	return ret;
+}
+
+static int __devexit ab8500_gpadc_remove(struct platform_device *pdev)
+{
+	struct ab8500_gpadc *gpadc = platform_get_drvdata(pdev);
+
+	/* remove this gpadc entry from the list */
+	list_del(&gpadc->node);
+	/* remove interrupt  - completion of Sw ADC conversion */
+	free_irq(gpadc->irq, gpadc);
+	/* disable VTVout LDO that is being used by GPADC */
+	regulator_put(gpadc->regu);
+	kfree(gpadc);
+	gpadc = NULL;
+	return 0;
+}
+
+static struct platform_driver ab8500_gpadc_driver = {
+	.probe = ab8500_gpadc_probe,
+	.remove = __devexit_p(ab8500_gpadc_remove),
+	.driver = {
+		.name = "ab8500-gpadc",
+		.owner = THIS_MODULE,
+	},
+};
+
+static int __init ab8500_gpadc_init(void)
+{
+	return platform_driver_register(&ab8500_gpadc_driver);
+}
+
+static void __exit ab8500_gpadc_exit(void)
+{
+	platform_driver_unregister(&ab8500_gpadc_driver);
+}
+
+subsys_initcall_sync(ab8500_gpadc_init);
+module_exit(ab8500_gpadc_exit);
+
+MODULE_LICENSE("GPL v2");
+MODULE_AUTHOR("Arun R Murthy, Daniel Willerud, Johan Palsson");
+MODULE_ALIAS("platform:ab8500_gpadc");
+MODULE_DESCRIPTION("AB8500 GPADC driver");
diff --git a/drivers/mfd/ab8500-sysctrl.c b/drivers/mfd/ab8500-sysctrl.c
new file mode 100644
index 0000000..3921859
--- /dev/null
+++ b/drivers/mfd/ab8500-sysctrl.c
@@ -0,0 +1,80 @@
+/*
+ * Copyright (C) ST-Ericsson SA 2010
+ * Author: Mattias Nilsson <mattias.i.nilsson@stericsson.com> for ST Ericsson.
+ * License terms: GNU General Public License (GPL) version 2
+ */
+
+#include <linux/err.h>
+#include <linux/platform_device.h>
+#include <linux/mfd/ab8500.h>
+#include <linux/mfd/abx500.h>
+#include <linux/mfd/ab8500/sysctrl.h>
+
+static struct device *sysctrl_dev;
+
+static inline bool valid_bank(u8 bank)
+{
+	return ((bank == AB8500_SYS_CTRL1_BLOCK) ||
+		(bank == AB8500_SYS_CTRL2_BLOCK));
+}
+
+int ab8500_sysctrl_read(u16 reg, u8 *value)
+{
+	u8 bank;
+
+	if (sysctrl_dev == NULL)
+		return -EAGAIN;
+
+	bank = (reg >> 8);
+	if (!valid_bank(bank))
+		return -EINVAL;
+
+	return abx500_get_register_interruptible(sysctrl_dev, bank,
+		(u8)(reg & 0xFF), value);
+}
+
+int ab8500_sysctrl_write(u16 reg, u8 mask, u8 value)
+{
+	u8 bank;
+
+	if (sysctrl_dev == NULL)
+		return -EAGAIN;
+
+	bank = (reg >> 8);
+	if (!valid_bank(bank))
+		return -EINVAL;
+
+	return abx500_mask_and_set_register_interruptible(sysctrl_dev, bank,
+		(u8)(reg & 0xFF), mask, value);
+}
+
+static int __devinit ab8500_sysctrl_probe(struct platform_device *pdev)
+{
+	sysctrl_dev = &pdev->dev;
+	return 0;
+}
+
+static int __devexit ab8500_sysctrl_remove(struct platform_device *pdev)
+{
+	sysctrl_dev = NULL;
+	return 0;
+}
+
+static struct platform_driver ab8500_sysctrl_driver = {
+	.driver = {
+		.name = "ab8500-sysctrl",
+		.owner = THIS_MODULE,
+	},
+	.probe = ab8500_sysctrl_probe,
+	.remove = __devexit_p(ab8500_sysctrl_remove),
+};
+
+static int __init ab8500_sysctrl_init(void)
+{
+	return platform_driver_register(&ab8500_sysctrl_driver);
+}
+subsys_initcall(ab8500_sysctrl_init);
+
+MODULE_AUTHOR("Mattias Nilsson <mattias.i.nilsson@stericsson.com");
+MODULE_DESCRIPTION("AB8500 system control driver");
+MODULE_LICENSE("GPL v2");
diff --git a/drivers/mfd/adp5520.c b/drivers/mfd/adp5520.c
index 3122139..f1d8848 100644
--- a/drivers/mfd/adp5520.c
+++ b/drivers/mfd/adp5520.c
@@ -321,27 +321,27 @@
 }
 
 #ifdef CONFIG_PM
-static int adp5520_suspend(struct i2c_client *client,
-				 pm_message_t state)
+static int adp5520_suspend(struct device *dev)
 {
+	struct i2c_client *client = to_i2c_client(dev);
 	struct adp5520_chip *chip = dev_get_drvdata(&client->dev);
 
 	adp5520_clr_bits(chip->dev, ADP5520_MODE_STATUS, ADP5520_nSTNBY);
 	return 0;
 }
 
-static int adp5520_resume(struct i2c_client *client)
+static int adp5520_resume(struct device *dev)
 {
+	struct i2c_client *client = to_i2c_client(dev);
 	struct adp5520_chip *chip = dev_get_drvdata(&client->dev);
 
 	adp5520_set_bits(chip->dev, ADP5520_MODE_STATUS, ADP5520_nSTNBY);
 	return 0;
 }
-#else
-#define adp5520_suspend	NULL
-#define adp5520_resume	NULL
 #endif
 
+static SIMPLE_DEV_PM_OPS(adp5520_pm, adp5520_suspend, adp5520_resume);
+
 static const struct i2c_device_id adp5520_id[] = {
 	{ "pmic-adp5520", ID_ADP5520 },
 	{ "pmic-adp5501", ID_ADP5501 },
@@ -353,11 +353,10 @@
 	.driver = {
 		.name	= "adp5520",
 		.owner	= THIS_MODULE,
+		.pm	= &adp5520_pm,
 	},
 	.probe		= adp5520_probe,
 	.remove		= __devexit_p(adp5520_remove),
-	.suspend	= adp5520_suspend,
-	.resume		= adp5520_resume,
 	.id_table 	= adp5520_id,
 };
 
diff --git a/drivers/mfd/asic3.c b/drivers/mfd/asic3.c
index c45e630..0241f08 100644
--- a/drivers/mfd/asic3.c
+++ b/drivers/mfd/asic3.c
@@ -682,7 +682,7 @@
 	.name          = "ds1wm",
 	.enable        = ds1wm_enable,
 	.disable       = ds1wm_disable,
-	.driver_data   = &ds1wm_pdata,
+	.mfd_data      = &ds1wm_pdata,
 	.num_resources = ARRAY_SIZE(ds1wm_resources),
 	.resources     = ds1wm_resources,
 };
@@ -783,7 +783,7 @@
 	.name          = "tmio-mmc",
 	.enable        = asic3_mmc_enable,
 	.disable       = asic3_mmc_disable,
-	.driver_data   = &asic3_mmc_data,
+	.mfd_data      = &asic3_mmc_data,
 	.num_resources = ARRAY_SIZE(asic3_mmc_resources),
 	.resources     = asic3_mmc_resources,
 };
@@ -810,9 +810,6 @@
 	ds1wm_resources[0].start >>= asic->bus_shift;
 	ds1wm_resources[0].end   >>= asic->bus_shift;
 
-	asic3_cell_ds1wm.platform_data = &asic3_cell_ds1wm;
-	asic3_cell_ds1wm.data_size = sizeof(asic3_cell_ds1wm);
-
 	/* MMC */
 	asic->tmio_cnf = ioremap((ASIC3_SD_CONFIG_BASE >> asic->bus_shift) +
 				 mem_sdio->start, 0x400 >> asic->bus_shift);
@@ -824,9 +821,6 @@
 	asic3_mmc_resources[0].start >>= asic->bus_shift;
 	asic3_mmc_resources[0].end   >>= asic->bus_shift;
 
-	asic3_cell_mmc.platform_data = &asic3_cell_mmc;
-	asic3_cell_mmc.data_size = sizeof(asic3_cell_mmc);
-
 	ret = mfd_add_devices(&pdev->dev, pdev->id,
 			&asic3_cell_ds1wm, 1, mem, asic->irq_base);
 	if (ret < 0)
diff --git a/drivers/mfd/cs5535-mfd.c b/drivers/mfd/cs5535-mfd.c
index 59ca6f1..886a068 100644
--- a/drivers/mfd/cs5535-mfd.c
+++ b/drivers/mfd/cs5535-mfd.c
@@ -39,6 +39,37 @@
 	NR_BARS,
 };
 
+static int cs5535_mfd_res_enable(struct platform_device *pdev)
+{
+	struct resource *res;
+
+	res = platform_get_resource(pdev, IORESOURCE_IO, 0);
+	if (!res) {
+		dev_err(&pdev->dev, "can't fetch device resource info\n");
+		return -EIO;
+	}
+
+	if (!request_region(res->start, resource_size(res), DRV_NAME)) {
+		dev_err(&pdev->dev, "can't request region\n");
+		return -EIO;
+	}
+
+	return 0;
+}
+
+static int cs5535_mfd_res_disable(struct platform_device *pdev)
+{
+	struct resource *res;
+	res = platform_get_resource(pdev, IORESOURCE_IO, 0);
+	if (!res) {
+		dev_err(&pdev->dev, "can't fetch device resource info\n");
+		return -EIO;
+	}
+
+	release_region(res->start, resource_size(res));
+	return 0;
+}
+
 static __devinitdata struct resource cs5535_mfd_resources[NR_BARS];
 
 static __devinitdata struct mfd_cell cs5535_mfd_cells[] = {
@@ -65,12 +96,18 @@
 		.name = "cs5535-pms",
 		.num_resources = 1,
 		.resources = &cs5535_mfd_resources[PMS_BAR],
+
+		.enable = cs5535_mfd_res_enable,
+		.disable = cs5535_mfd_res_disable,
 	},
 	{
 		.id = ACPI_BAR,
 		.name = "cs5535-acpi",
 		.num_resources = 1,
 		.resources = &cs5535_mfd_resources[ACPI_BAR],
+
+		.enable = cs5535_mfd_res_enable,
+		.disable = cs5535_mfd_res_disable,
 	},
 };
 
diff --git a/drivers/mfd/davinci_voicecodec.c b/drivers/mfd/davinci_voicecodec.c
index fdd8a1b..414783b 100644
--- a/drivers/mfd/davinci_voicecodec.c
+++ b/drivers/mfd/davinci_voicecodec.c
@@ -119,12 +119,12 @@
 	/* Voice codec interface client */
 	cell = &davinci_vc->cells[DAVINCI_VC_VCIF_CELL];
 	cell->name = "davinci-vcif";
-	cell->driver_data = davinci_vc;
+	cell->mfd_data = davinci_vc;
 
 	/* Voice codec CQ93VC client */
 	cell = &davinci_vc->cells[DAVINCI_VC_CQ93VC_CELL];
 	cell->name = "cq93vc-codec";
-	cell->driver_data = davinci_vc;
+	cell->mfd_data = davinci_vc;
 
 	ret = mfd_add_devices(&pdev->dev, pdev->id, davinci_vc->cells,
 			      DAVINCI_VC_CELLS, NULL, 0);
diff --git a/drivers/mfd/htc-pasic3.c b/drivers/mfd/htc-pasic3.c
index 7bc7522..fb9770b 100644
--- a/drivers/mfd/htc-pasic3.c
+++ b/drivers/mfd/htc-pasic3.c
@@ -117,7 +117,7 @@
 	.name          = "ds1wm",
 	.enable        = ds1wm_enable,
 	.disable       = ds1wm_disable,
-	.driver_data   = &ds1wm_pdata,
+	.mfd_data      = &ds1wm_pdata,
 	.num_resources = 2,
 	.resources     = ds1wm_resources,
 };
@@ -165,8 +165,6 @@
 		ds1wm_pdata.clock_rate = pdata->clock_rate;
 		/* the first 5 PASIC3 registers control the DS1WM */
 		ds1wm_resources[0].end = (5 << asic->bus_shift) - 1;
-		ds1wm_cell.platform_data = &ds1wm_cell;
-		ds1wm_cell.data_size = sizeof(ds1wm_cell);
 		ret = mfd_add_devices(&pdev->dev, pdev->id,
 				&ds1wm_cell, 1, r, irq);
 		if (ret < 0)
@@ -174,9 +172,6 @@
 	}
 
 	if (pdata && pdata->led_pdata) {
-		led_cell.driver_data = pdata->led_pdata;
-		led_cell.platform_data = &led_cell;
-		led_cell.data_size = sizeof(ds1wm_cell);
 		ret = mfd_add_devices(&pdev->dev, pdev->id, &led_cell, 1, r, 0);
 		if (ret < 0)
 			dev_warn(dev, "failed to register LED device\n");
diff --git a/drivers/mfd/janz-cmodio.c b/drivers/mfd/janz-cmodio.c
index 36a166b..fc41911 100644
--- a/drivers/mfd/janz-cmodio.c
+++ b/drivers/mfd/janz-cmodio.c
@@ -86,8 +86,7 @@
 
 	/* Add platform data */
 	pdata->modno = modno;
-	cell->platform_data = pdata;
-	cell->data_size = sizeof(*pdata);
+	cell->mfd_data = pdata;
 
 	/* MODULbus registers -- PCI BAR3 is big-endian MODULbus access */
 	res->flags = IORESOURCE_MEM;
diff --git a/drivers/mfd/jz4740-adc.c b/drivers/mfd/jz4740-adc.c
index 0cc5979..aa518b9 100644
--- a/drivers/mfd/jz4740-adc.c
+++ b/drivers/mfd/jz4740-adc.c
@@ -232,8 +232,6 @@
 		.name = "jz4740-hwmon",
 		.num_resources = ARRAY_SIZE(jz4740_hwmon_resources),
 		.resources = jz4740_hwmon_resources,
-		.platform_data = (void *)&jz4740_adc_cells[0],
-		.data_size = sizeof(struct mfd_cell),
 
 		.enable = jz4740_adc_cell_enable,
 		.disable = jz4740_adc_cell_disable,
@@ -243,8 +241,6 @@
 		.name = "jz4740-battery",
 		.num_resources = ARRAY_SIZE(jz4740_battery_resources),
 		.resources = jz4740_battery_resources,
-		.platform_data = (void *)&jz4740_adc_cells[1],
-		.data_size = sizeof(struct mfd_cell),
 
 		.enable = jz4740_adc_cell_enable,
 		.disable = jz4740_adc_cell_disable,
diff --git a/drivers/mfd/lpc_sch.c b/drivers/mfd/lpc_sch.c
index 51b2f60..ea3f52c 100644
--- a/drivers/mfd/lpc_sch.c
+++ b/drivers/mfd/lpc_sch.c
@@ -61,6 +61,7 @@
 
 static struct pci_device_id lpc_sch_ids[] = {
 	{ PCI_DEVICE(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_SCH_LPC) },
+	{ PCI_DEVICE(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_ITC_LPC) },
 	{ 0, }
 };
 MODULE_DEVICE_TABLE(pci, lpc_sch_ids);
@@ -70,6 +71,7 @@
 {
 	unsigned int base_addr_cfg;
 	unsigned short base_addr;
+	int i;
 
 	pci_read_config_dword(dev, SMBASE, &base_addr_cfg);
 	if (!(base_addr_cfg & (1 << 31))) {
@@ -99,7 +101,10 @@
 	gpio_sch_resource.start = base_addr;
 	gpio_sch_resource.end = base_addr + GPIO_IO_SIZE - 1;
 
-	return mfd_add_devices(&dev->dev, -1,
+	for (i=0; i < ARRAY_SIZE(lpc_sch_cells); i++)
+		lpc_sch_cells[i].id = id->device;
+
+	return mfd_add_devices(&dev->dev, 0,
 			lpc_sch_cells, ARRAY_SIZE(lpc_sch_cells), NULL, 0);
 }
 
diff --git a/drivers/mfd/max8997.c b/drivers/mfd/max8997.c
new file mode 100644
index 0000000..5d1fca0
--- /dev/null
+++ b/drivers/mfd/max8997.c
@@ -0,0 +1,427 @@
+/*
+ * max8997.c - mfd core driver for the Maxim 8966 and 8997
+ *
+ * Copyright (C) 2011 Samsung Electronics
+ * MyungJoo Ham <myungjoo.ham@smasung.com>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA  02111-1307  USA
+ *
+ * This driver is based on max8998.c
+ */
+
+#include <linux/slab.h>
+#include <linux/i2c.h>
+#include <linux/pm_runtime.h>
+#include <linux/mutex.h>
+#include <linux/mfd/core.h>
+#include <linux/mfd/max8997.h>
+#include <linux/mfd/max8997-private.h>
+
+#define I2C_ADDR_PMIC	(0xCC >> 1)
+#define I2C_ADDR_MUIC	(0x4A >> 1)
+#define I2C_ADDR_BATTERY	(0x6C >> 1)
+#define I2C_ADDR_RTC	(0x0C >> 1)
+#define I2C_ADDR_HAPTIC	(0x90 >> 1)
+
+static struct mfd_cell max8997_devs[] = {
+	{ .name = "max8997-pmic", },
+	{ .name = "max8997-rtc", },
+	{ .name = "max8997-battery", },
+	{ .name = "max8997-haptic", },
+	{ .name = "max8997-muic", },
+	{ .name = "max8997-flash", },
+};
+
+int max8997_read_reg(struct i2c_client *i2c, u8 reg, u8 *dest)
+{
+	struct max8997_dev *max8997 = i2c_get_clientdata(i2c);
+	int ret;
+
+	mutex_lock(&max8997->iolock);
+	ret = i2c_smbus_read_byte_data(i2c, reg);
+	mutex_unlock(&max8997->iolock);
+	if (ret < 0)
+		return ret;
+
+	ret &= 0xff;
+	*dest = ret;
+	return 0;
+}
+EXPORT_SYMBOL_GPL(max8997_read_reg);
+
+int max8997_bulk_read(struct i2c_client *i2c, u8 reg, int count, u8 *buf)
+{
+	struct max8997_dev *max8997 = i2c_get_clientdata(i2c);
+	int ret;
+
+	mutex_lock(&max8997->iolock);
+	ret = i2c_smbus_read_i2c_block_data(i2c, reg, count, buf);
+	mutex_unlock(&max8997->iolock);
+	if (ret < 0)
+		return ret;
+
+	return 0;
+}
+EXPORT_SYMBOL_GPL(max8997_bulk_read);
+
+int max8997_write_reg(struct i2c_client *i2c, u8 reg, u8 value)
+{
+	struct max8997_dev *max8997 = i2c_get_clientdata(i2c);
+	int ret;
+
+	mutex_lock(&max8997->iolock);
+	ret = i2c_smbus_write_byte_data(i2c, reg, value);
+	mutex_unlock(&max8997->iolock);
+	return ret;
+}
+EXPORT_SYMBOL_GPL(max8997_write_reg);
+
+int max8997_bulk_write(struct i2c_client *i2c, u8 reg, int count, u8 *buf)
+{
+	struct max8997_dev *max8997 = i2c_get_clientdata(i2c);
+	int ret;
+
+	mutex_lock(&max8997->iolock);
+	ret = i2c_smbus_write_i2c_block_data(i2c, reg, count, buf);
+	mutex_unlock(&max8997->iolock);
+	if (ret < 0)
+		return ret;
+
+	return 0;
+}
+EXPORT_SYMBOL_GPL(max8997_bulk_write);
+
+int max8997_update_reg(struct i2c_client *i2c, u8 reg, u8 val, u8 mask)
+{
+	struct max8997_dev *max8997 = i2c_get_clientdata(i2c);
+	int ret;
+
+	mutex_lock(&max8997->iolock);
+	ret = i2c_smbus_read_byte_data(i2c, reg);
+	if (ret >= 0) {
+		u8 old_val = ret & 0xff;
+		u8 new_val = (val & mask) | (old_val & (~mask));
+		ret = i2c_smbus_write_byte_data(i2c, reg, new_val);
+	}
+	mutex_unlock(&max8997->iolock);
+	return ret;
+}
+EXPORT_SYMBOL_GPL(max8997_update_reg);
+
+static int max8997_i2c_probe(struct i2c_client *i2c,
+			    const struct i2c_device_id *id)
+{
+	struct max8997_dev *max8997;
+	struct max8997_platform_data *pdata = i2c->dev.platform_data;
+	int ret = 0;
+
+	max8997 = kzalloc(sizeof(struct max8997_dev), GFP_KERNEL);
+	if (max8997 == NULL)
+		return -ENOMEM;
+
+	i2c_set_clientdata(i2c, max8997);
+	max8997->dev = &i2c->dev;
+	max8997->i2c = i2c;
+	max8997->type = id->driver_data;
+
+	if (!pdata)
+		goto err;
+
+	max8997->wakeup = pdata->wakeup;
+
+	mutex_init(&max8997->iolock);
+
+	max8997->rtc = i2c_new_dummy(i2c->adapter, I2C_ADDR_RTC);
+	i2c_set_clientdata(max8997->rtc, max8997);
+	max8997->haptic = i2c_new_dummy(i2c->adapter, I2C_ADDR_HAPTIC);
+	i2c_set_clientdata(max8997->haptic, max8997);
+	max8997->muic = i2c_new_dummy(i2c->adapter, I2C_ADDR_MUIC);
+	i2c_set_clientdata(max8997->muic, max8997);
+
+	pm_runtime_set_active(max8997->dev);
+
+	mfd_add_devices(max8997->dev, -1, max8997_devs,
+			ARRAY_SIZE(max8997_devs),
+			NULL, 0);
+
+	/*
+	 * TODO: enable others (flash, muic, rtc, battery, ...) and
+	 * check the return value
+	 */
+
+	if (ret < 0)
+		goto err_mfd;
+
+	return ret;
+
+err_mfd:
+	mfd_remove_devices(max8997->dev);
+	i2c_unregister_device(max8997->muic);
+	i2c_unregister_device(max8997->haptic);
+	i2c_unregister_device(max8997->rtc);
+err:
+	kfree(max8997);
+	return ret;
+}
+
+static int max8997_i2c_remove(struct i2c_client *i2c)
+{
+	struct max8997_dev *max8997 = i2c_get_clientdata(i2c);
+
+	mfd_remove_devices(max8997->dev);
+	i2c_unregister_device(max8997->muic);
+	i2c_unregister_device(max8997->haptic);
+	i2c_unregister_device(max8997->rtc);
+	kfree(max8997);
+
+	return 0;
+}
+
+static const struct i2c_device_id max8997_i2c_id[] = {
+	{ "max8997", TYPE_MAX8997 },
+	{ "max8966", TYPE_MAX8966 },
+	{ }
+};
+MODULE_DEVICE_TABLE(i2c, max8998_i2c_id);
+
+u8 max8997_dumpaddr_pmic[] = {
+	MAX8997_REG_INT1MSK,
+	MAX8997_REG_INT2MSK,
+	MAX8997_REG_INT3MSK,
+	MAX8997_REG_INT4MSK,
+	MAX8997_REG_MAINCON1,
+	MAX8997_REG_MAINCON2,
+	MAX8997_REG_BUCKRAMP,
+	MAX8997_REG_BUCK1CTRL,
+	MAX8997_REG_BUCK1DVS1,
+	MAX8997_REG_BUCK1DVS2,
+	MAX8997_REG_BUCK1DVS3,
+	MAX8997_REG_BUCK1DVS4,
+	MAX8997_REG_BUCK1DVS5,
+	MAX8997_REG_BUCK1DVS6,
+	MAX8997_REG_BUCK1DVS7,
+	MAX8997_REG_BUCK1DVS8,
+	MAX8997_REG_BUCK2CTRL,
+	MAX8997_REG_BUCK2DVS1,
+	MAX8997_REG_BUCK2DVS2,
+	MAX8997_REG_BUCK2DVS3,
+	MAX8997_REG_BUCK2DVS4,
+	MAX8997_REG_BUCK2DVS5,
+	MAX8997_REG_BUCK2DVS6,
+	MAX8997_REG_BUCK2DVS7,
+	MAX8997_REG_BUCK2DVS8,
+	MAX8997_REG_BUCK3CTRL,
+	MAX8997_REG_BUCK3DVS,
+	MAX8997_REG_BUCK4CTRL,
+	MAX8997_REG_BUCK4DVS,
+	MAX8997_REG_BUCK5CTRL,
+	MAX8997_REG_BUCK5DVS1,
+	MAX8997_REG_BUCK5DVS2,
+	MAX8997_REG_BUCK5DVS3,
+	MAX8997_REG_BUCK5DVS4,
+	MAX8997_REG_BUCK5DVS5,
+	MAX8997_REG_BUCK5DVS6,
+	MAX8997_REG_BUCK5DVS7,
+	MAX8997_REG_BUCK5DVS8,
+	MAX8997_REG_BUCK6CTRL,
+	MAX8997_REG_BUCK6BPSKIPCTRL,
+	MAX8997_REG_BUCK7CTRL,
+	MAX8997_REG_BUCK7DVS,
+	MAX8997_REG_LDO1CTRL,
+	MAX8997_REG_LDO2CTRL,
+	MAX8997_REG_LDO3CTRL,
+	MAX8997_REG_LDO4CTRL,
+	MAX8997_REG_LDO5CTRL,
+	MAX8997_REG_LDO6CTRL,
+	MAX8997_REG_LDO7CTRL,
+	MAX8997_REG_LDO8CTRL,
+	MAX8997_REG_LDO9CTRL,
+	MAX8997_REG_LDO10CTRL,
+	MAX8997_REG_LDO11CTRL,
+	MAX8997_REG_LDO12CTRL,
+	MAX8997_REG_LDO13CTRL,
+	MAX8997_REG_LDO14CTRL,
+	MAX8997_REG_LDO15CTRL,
+	MAX8997_REG_LDO16CTRL,
+	MAX8997_REG_LDO17CTRL,
+	MAX8997_REG_LDO18CTRL,
+	MAX8997_REG_LDO21CTRL,
+	MAX8997_REG_MBCCTRL1,
+	MAX8997_REG_MBCCTRL2,
+	MAX8997_REG_MBCCTRL3,
+	MAX8997_REG_MBCCTRL4,
+	MAX8997_REG_MBCCTRL5,
+	MAX8997_REG_MBCCTRL6,
+	MAX8997_REG_OTPCGHCVS,
+	MAX8997_REG_SAFEOUTCTRL,
+	MAX8997_REG_LBCNFG1,
+	MAX8997_REG_LBCNFG2,
+	MAX8997_REG_BBCCTRL,
+
+	MAX8997_REG_FLASH1_CUR,
+	MAX8997_REG_FLASH2_CUR,
+	MAX8997_REG_MOVIE_CUR,
+	MAX8997_REG_GSMB_CUR,
+	MAX8997_REG_BOOST_CNTL,
+	MAX8997_REG_LEN_CNTL,
+	MAX8997_REG_FLASH_CNTL,
+	MAX8997_REG_WDT_CNTL,
+	MAX8997_REG_MAXFLASH1,
+	MAX8997_REG_MAXFLASH2,
+	MAX8997_REG_FLASHSTATUSMASK,
+
+	MAX8997_REG_GPIOCNTL1,
+	MAX8997_REG_GPIOCNTL2,
+	MAX8997_REG_GPIOCNTL3,
+	MAX8997_REG_GPIOCNTL4,
+	MAX8997_REG_GPIOCNTL5,
+	MAX8997_REG_GPIOCNTL6,
+	MAX8997_REG_GPIOCNTL7,
+	MAX8997_REG_GPIOCNTL8,
+	MAX8997_REG_GPIOCNTL9,
+	MAX8997_REG_GPIOCNTL10,
+	MAX8997_REG_GPIOCNTL11,
+	MAX8997_REG_GPIOCNTL12,
+
+	MAX8997_REG_LDO1CONFIG,
+	MAX8997_REG_LDO2CONFIG,
+	MAX8997_REG_LDO3CONFIG,
+	MAX8997_REG_LDO4CONFIG,
+	MAX8997_REG_LDO5CONFIG,
+	MAX8997_REG_LDO6CONFIG,
+	MAX8997_REG_LDO7CONFIG,
+	MAX8997_REG_LDO8CONFIG,
+	MAX8997_REG_LDO9CONFIG,
+	MAX8997_REG_LDO10CONFIG,
+	MAX8997_REG_LDO11CONFIG,
+	MAX8997_REG_LDO12CONFIG,
+	MAX8997_REG_LDO13CONFIG,
+	MAX8997_REG_LDO14CONFIG,
+	MAX8997_REG_LDO15CONFIG,
+	MAX8997_REG_LDO16CONFIG,
+	MAX8997_REG_LDO17CONFIG,
+	MAX8997_REG_LDO18CONFIG,
+	MAX8997_REG_LDO21CONFIG,
+
+	MAX8997_REG_DVSOKTIMER1,
+	MAX8997_REG_DVSOKTIMER2,
+	MAX8997_REG_DVSOKTIMER4,
+	MAX8997_REG_DVSOKTIMER5,
+};
+
+u8 max8997_dumpaddr_muic[] = {
+	MAX8997_MUIC_REG_INTMASK1,
+	MAX8997_MUIC_REG_INTMASK2,
+	MAX8997_MUIC_REG_INTMASK3,
+	MAX8997_MUIC_REG_CDETCTRL,
+	MAX8997_MUIC_REG_CONTROL1,
+	MAX8997_MUIC_REG_CONTROL2,
+	MAX8997_MUIC_REG_CONTROL3,
+};
+
+u8 max8997_dumpaddr_haptic[] = {
+	MAX8997_HAPTIC_REG_CONF1,
+	MAX8997_HAPTIC_REG_CONF2,
+	MAX8997_HAPTIC_REG_DRVCONF,
+	MAX8997_HAPTIC_REG_CYCLECONF1,
+	MAX8997_HAPTIC_REG_CYCLECONF2,
+	MAX8997_HAPTIC_REG_SIGCONF1,
+	MAX8997_HAPTIC_REG_SIGCONF2,
+	MAX8997_HAPTIC_REG_SIGCONF3,
+	MAX8997_HAPTIC_REG_SIGCONF4,
+	MAX8997_HAPTIC_REG_SIGDC1,
+	MAX8997_HAPTIC_REG_SIGDC2,
+	MAX8997_HAPTIC_REG_SIGPWMDC1,
+	MAX8997_HAPTIC_REG_SIGPWMDC2,
+	MAX8997_HAPTIC_REG_SIGPWMDC3,
+	MAX8997_HAPTIC_REG_SIGPWMDC4,
+};
+
+static int max8997_freeze(struct device *dev)
+{
+	struct i2c_client *i2c = container_of(dev, struct i2c_client, dev);
+	struct max8997_dev *max8997 = i2c_get_clientdata(i2c);
+	int i;
+
+	for (i = 0; i < ARRAY_SIZE(max8997_dumpaddr_pmic); i++)
+		max8997_read_reg(i2c, max8997_dumpaddr_pmic[i],
+				&max8997->reg_dump[i]);
+
+	for (i = 0; i < ARRAY_SIZE(max8997_dumpaddr_muic); i++)
+		max8997_read_reg(i2c, max8997_dumpaddr_muic[i],
+				&max8997->reg_dump[i + MAX8997_REG_PMIC_END]);
+
+	for (i = 0; i < ARRAY_SIZE(max8997_dumpaddr_haptic); i++)
+		max8997_read_reg(i2c, max8997_dumpaddr_haptic[i],
+				&max8997->reg_dump[i + MAX8997_REG_PMIC_END +
+				MAX8997_MUIC_REG_END]);
+
+	return 0;
+}
+
+static int max8997_restore(struct device *dev)
+{
+	struct i2c_client *i2c = container_of(dev, struct i2c_client, dev);
+	struct max8997_dev *max8997 = i2c_get_clientdata(i2c);
+	int i;
+
+	for (i = 0; i < ARRAY_SIZE(max8997_dumpaddr_pmic); i++)
+		max8997_write_reg(i2c, max8997_dumpaddr_pmic[i],
+				max8997->reg_dump[i]);
+
+	for (i = 0; i < ARRAY_SIZE(max8997_dumpaddr_muic); i++)
+		max8997_write_reg(i2c, max8997_dumpaddr_muic[i],
+				max8997->reg_dump[i + MAX8997_REG_PMIC_END]);
+
+	for (i = 0; i < ARRAY_SIZE(max8997_dumpaddr_haptic); i++)
+		max8997_write_reg(i2c, max8997_dumpaddr_haptic[i],
+				max8997->reg_dump[i + MAX8997_REG_PMIC_END +
+				MAX8997_MUIC_REG_END]);
+
+	return 0;
+}
+
+const struct dev_pm_ops max8997_pm = {
+	.freeze = max8997_freeze,
+	.restore = max8997_restore,
+};
+
+static struct i2c_driver max8997_i2c_driver = {
+	.driver = {
+		   .name = "max8997",
+		   .owner = THIS_MODULE,
+		   .pm = &max8997_pm,
+	},
+	.probe = max8997_i2c_probe,
+	.remove = max8997_i2c_remove,
+	.id_table = max8997_i2c_id,
+};
+
+static int __init max8997_i2c_init(void)
+{
+	return i2c_add_driver(&max8997_i2c_driver);
+}
+/* init early so consumer devices can complete system boot */
+subsys_initcall(max8997_i2c_init);
+
+static void __exit max8997_i2c_exit(void)
+{
+	i2c_del_driver(&max8997_i2c_driver);
+}
+module_exit(max8997_i2c_exit);
+
+MODULE_DESCRIPTION("MAXIM 8997 multi-function core driver");
+MODULE_AUTHOR("MyungJoo Ham <myungjoo.ham@samsung.com>");
+MODULE_LICENSE("GPL");
diff --git a/drivers/mfd/max8998.c b/drivers/mfd/max8998.c
index bbfe867..c002142 100644
--- a/drivers/mfd/max8998.c
+++ b/drivers/mfd/max8998.c
@@ -233,7 +233,7 @@
 	u8	val;
 };
 #define SAVE_ITEM(x)	{ .addr = (x), .val = 0x0, }
-struct max8998_reg_dump max8998_dump[] = {
+static struct max8998_reg_dump max8998_dump[] = {
 	SAVE_ITEM(MAX8998_REG_IRQM1),
 	SAVE_ITEM(MAX8998_REG_IRQM2),
 	SAVE_ITEM(MAX8998_REG_IRQM3),
@@ -298,7 +298,7 @@
 	return 0;
 }
 
-const struct dev_pm_ops max8998_pm = {
+static const struct dev_pm_ops max8998_pm = {
 	.suspend = max8998_suspend,
 	.resume = max8998_resume,
 	.freeze = max8998_freeze,
diff --git a/drivers/mfd/mc13xxx-core.c b/drivers/mfd/mc13xxx-core.c
index b9fcaf0..668634e 100644
--- a/drivers/mfd/mc13xxx-core.c
+++ b/drivers/mfd/mc13xxx-core.c
@@ -683,14 +683,13 @@
 EXPORT_SYMBOL_GPL(mc13783_adc_do_conversion);
 
 static int mc13xxx_add_subdevice_pdata(struct mc13xxx *mc13xxx,
-		const char *format, void *pdata, size_t pdata_size)
+		const char *format, void *pdata)
 {
 	char buf[30];
 	const char *name = mc13xxx_get_chipname(mc13xxx);
 
 	struct mfd_cell cell = {
-		.platform_data = pdata,
-		.data_size = pdata_size,
+		.mfd_data = pdata,
 	};
 
 	/* there is no asnprintf in the kernel :-( */
@@ -706,7 +705,7 @@
 
 static int mc13xxx_add_subdevice(struct mc13xxx *mc13xxx, const char *format)
 {
-	return mc13xxx_add_subdevice_pdata(mc13xxx, format, NULL, 0);
+	return mc13xxx_add_subdevice_pdata(mc13xxx, format, NULL);
 }
 
 static int mc13xxx_probe(struct spi_device *spi)
@@ -764,13 +763,8 @@
 		mc13xxx_add_subdevice(mc13xxx, "%s-codec");
 
 	if (pdata->flags & MC13XXX_USE_REGULATOR) {
-		struct mc13xxx_regulator_platform_data regulator_pdata = {
-			.num_regulators = pdata->num_regulators,
-			.regulators = pdata->regulators,
-		};
-
 		mc13xxx_add_subdevice_pdata(mc13xxx, "%s-regulator",
-				&regulator_pdata, sizeof(regulator_pdata));
+				&pdata->regulators);
 	}
 
 	if (pdata->flags & MC13XXX_USE_RTC)
@@ -779,10 +773,8 @@
 	if (pdata->flags & MC13XXX_USE_TOUCHSCREEN)
 		mc13xxx_add_subdevice(mc13xxx, "%s-ts");
 
-	if (pdata->flags & MC13XXX_USE_LED) {
-		mc13xxx_add_subdevice_pdata(mc13xxx, "%s-led",
-					pdata->leds, sizeof(*pdata->leds));
-	}
+	if (pdata->flags & MC13XXX_USE_LED)
+		mc13xxx_add_subdevice_pdata(mc13xxx, "%s-led", pdata->leds);
 
 	return 0;
 }
@@ -811,6 +803,7 @@
 		/* sentinel */
 	}
 };
+MODULE_DEVICE_TABLE(spi, mc13xxx_device_id);
 
 static struct spi_driver mc13xxx_driver = {
 	.id_table = mc13xxx_device_id,
diff --git a/drivers/mfd/mfd-core.c b/drivers/mfd/mfd-core.c
index d83ad0f..79eda02 100644
--- a/drivers/mfd/mfd-core.c
+++ b/drivers/mfd/mfd-core.c
@@ -18,6 +18,43 @@
 #include <linux/pm_runtime.h>
 #include <linux/slab.h>
 
+int mfd_cell_enable(struct platform_device *pdev)
+{
+	const struct mfd_cell *cell = mfd_get_cell(pdev);
+	int err = 0;
+
+	/* only call enable hook if the cell wasn't previously enabled */
+	if (atomic_inc_return(cell->usage_count) == 1)
+		err = cell->enable(pdev);
+
+	/* if the enable hook failed, decrement counter to allow retries */
+	if (err)
+		atomic_dec(cell->usage_count);
+
+	return err;
+}
+EXPORT_SYMBOL(mfd_cell_enable);
+
+int mfd_cell_disable(struct platform_device *pdev)
+{
+	const struct mfd_cell *cell = mfd_get_cell(pdev);
+	int err = 0;
+
+	/* only disable if no other clients are using it */
+	if (atomic_dec_return(cell->usage_count) == 0)
+		err = cell->disable(pdev);
+
+	/* if the disable hook failed, increment to allow retries */
+	if (err)
+		atomic_inc(cell->usage_count);
+
+	/* sanity check; did someone call disable too many times? */
+	WARN_ON(atomic_read(cell->usage_count) < 0);
+
+	return err;
+}
+EXPORT_SYMBOL(mfd_cell_disable);
+
 static int mfd_add_device(struct device *parent, int id,
 			  const struct mfd_cell *cell,
 			  struct resource *mem_base,
@@ -37,14 +74,10 @@
 		goto fail_device;
 
 	pdev->dev.parent = parent;
-	platform_set_drvdata(pdev, cell->driver_data);
 
-	if (cell->data_size) {
-		ret = platform_device_add_data(pdev,
-					cell->platform_data, cell->data_size);
-		if (ret)
-			goto fail_res;
-	}
+	ret = platform_device_add_data(pdev, cell, sizeof(*cell));
+	if (ret)
+		goto fail_res;
 
 	for (r = 0; r < cell->num_resources; r++) {
 		res[r].name = cell->resources[r].name;
@@ -100,14 +133,22 @@
 }
 
 int mfd_add_devices(struct device *parent, int id,
-		    const struct mfd_cell *cells, int n_devs,
+		    struct mfd_cell *cells, int n_devs,
 		    struct resource *mem_base,
 		    int irq_base)
 {
 	int i;
 	int ret = 0;
+	atomic_t *cnts;
+
+	/* initialize reference counting for all cells */
+	cnts = kcalloc(sizeof(*cnts), n_devs, GFP_KERNEL);
+	if (!cnts)
+		return -ENOMEM;
 
 	for (i = 0; i < n_devs; i++) {
+		atomic_set(&cnts[i], 0);
+		cells[i].usage_count = &cnts[i];
 		ret = mfd_add_device(parent, id, cells + i, mem_base, irq_base);
 		if (ret)
 			break;
@@ -120,17 +161,89 @@
 }
 EXPORT_SYMBOL(mfd_add_devices);
 
-static int mfd_remove_devices_fn(struct device *dev, void *unused)
+static int mfd_remove_devices_fn(struct device *dev, void *c)
 {
-	platform_device_unregister(to_platform_device(dev));
+	struct platform_device *pdev = to_platform_device(dev);
+	const struct mfd_cell *cell = mfd_get_cell(pdev);
+	atomic_t **usage_count = c;
+
+	/* find the base address of usage_count pointers (for freeing) */
+	if (!*usage_count || (cell->usage_count < *usage_count))
+		*usage_count = cell->usage_count;
+
+	platform_device_unregister(pdev);
 	return 0;
 }
 
 void mfd_remove_devices(struct device *parent)
 {
-	device_for_each_child(parent, NULL, mfd_remove_devices_fn);
+	atomic_t *cnts = NULL;
+
+	device_for_each_child(parent, &cnts, mfd_remove_devices_fn);
+	kfree(cnts);
 }
 EXPORT_SYMBOL(mfd_remove_devices);
 
+static int add_shared_platform_device(const char *cell, const char *name)
+{
+	struct mfd_cell cell_entry;
+	struct device *dev;
+	struct platform_device *pdev;
+	int err;
+
+	/* check if we've already registered a device (don't fail if we have) */
+	if (bus_find_device_by_name(&platform_bus_type, NULL, name))
+		return 0;
+
+	/* fetch the parent cell's device (should already be registered!) */
+	dev = bus_find_device_by_name(&platform_bus_type, NULL, cell);
+	if (!dev) {
+		printk(KERN_ERR "failed to find device for cell %s\n", cell);
+		return -ENODEV;
+	}
+	pdev = to_platform_device(dev);
+	memcpy(&cell_entry, mfd_get_cell(pdev), sizeof(cell_entry));
+
+	WARN_ON(!cell_entry.enable);
+
+	cell_entry.name = name;
+	err = mfd_add_device(pdev->dev.parent, -1, &cell_entry, NULL, 0);
+	if (err)
+		dev_err(dev, "MFD add devices failed: %d\n", err);
+	return err;
+}
+
+int mfd_shared_platform_driver_register(struct platform_driver *drv,
+		const char *cellname)
+{
+	int err;
+
+	err = add_shared_platform_device(cellname, drv->driver.name);
+	if (err)
+		printk(KERN_ERR "failed to add platform device %s\n",
+				drv->driver.name);
+
+	err = platform_driver_register(drv);
+	if (err)
+		printk(KERN_ERR "failed to add platform driver %s\n",
+				drv->driver.name);
+
+	return err;
+}
+EXPORT_SYMBOL(mfd_shared_platform_driver_register);
+
+void mfd_shared_platform_driver_unregister(struct platform_driver *drv)
+{
+	struct device *dev;
+
+	dev = bus_find_device_by_name(&platform_bus_type, NULL,
+			drv->driver.name);
+	if (dev)
+		platform_device_unregister(to_platform_device(dev));
+
+	platform_driver_unregister(drv);
+}
+EXPORT_SYMBOL(mfd_shared_platform_driver_unregister);
+
 MODULE_LICENSE("GPL");
 MODULE_AUTHOR("Ian Molton, Dmitry Baryshkov");
diff --git a/drivers/mfd/pcf50633-core.c b/drivers/mfd/pcf50633-core.c
index 501ce13..c1306ed 100644
--- a/drivers/mfd/pcf50633-core.c
+++ b/drivers/mfd/pcf50633-core.c
@@ -21,6 +21,7 @@
 #include <linux/workqueue.h>
 #include <linux/platform_device.h>
 #include <linux/i2c.h>
+#include <linux/pm.h>
 #include <linux/slab.h>
 
 #include <linux/mfd/pcf50633/core.h>
@@ -230,27 +231,26 @@
 	}
 }
 
-#ifdef CONFIG_PM
-static int pcf50633_suspend(struct i2c_client *client, pm_message_t state)
+#ifdef CONFIG_PM_SLEEP
+static int pcf50633_suspend(struct device *dev)
 {
-	struct pcf50633 *pcf;
-	pcf = i2c_get_clientdata(client);
+	struct i2c_client *client = to_i2c_client(dev);
+	struct pcf50633 *pcf = i2c_get_clientdata(client);
 
 	return pcf50633_irq_suspend(pcf);
 }
 
-static int pcf50633_resume(struct i2c_client *client)
+static int pcf50633_resume(struct device *dev)
 {
-	struct pcf50633 *pcf;
-	pcf = i2c_get_clientdata(client);
+	struct i2c_client *client = to_i2c_client(dev);
+	struct pcf50633 *pcf = i2c_get_clientdata(client);
 
 	return pcf50633_irq_resume(pcf);
 }
-#else
-#define pcf50633_suspend NULL
-#define pcf50633_resume NULL
 #endif
 
+static SIMPLE_DEV_PM_OPS(pcf50633_pm, pcf50633_suspend, pcf50633_resume);
+
 static int __devinit pcf50633_probe(struct i2c_client *client,
 				const struct i2c_device_id *ids)
 {
@@ -360,16 +360,16 @@
 	{"pcf50633", 0x73},
 	{/* end of list */}
 };
+MODULE_DEVICE_TABLE(i2c, pcf50633_id_table);
 
 static struct i2c_driver pcf50633_driver = {
 	.driver = {
 		.name	= "pcf50633",
+		.pm	= &pcf50633_pm,
 	},
 	.id_table = pcf50633_id_table,
 	.probe = pcf50633_probe,
 	.remove = __devexit_p(pcf50633_remove),
-	.suspend = pcf50633_suspend,
-	.resume	= pcf50633_resume,
 };
 
 static int __init pcf50633_init(void)
diff --git a/drivers/mfd/rdc321x-southbridge.c b/drivers/mfd/rdc321x-southbridge.c
index 5092297..193c940 100644
--- a/drivers/mfd/rdc321x-southbridge.c
+++ b/drivers/mfd/rdc321x-southbridge.c
@@ -61,12 +61,12 @@
 		.name		= "rdc321x-wdt",
 		.resources	= rdc321x_wdt_resource,
 		.num_resources	= ARRAY_SIZE(rdc321x_wdt_resource),
-		.driver_data	= &rdc321x_wdt_pdata,
+		.mfd_data	= &rdc321x_wdt_pdata,
 	}, {
 		.name		= "rdc321x-gpio",
 		.resources	= rdc321x_gpio_resources,
 		.num_resources	= ARRAY_SIZE(rdc321x_gpio_resources),
-		.driver_data	= &rdc321x_gpio_pdata,
+		.mfd_data	= &rdc321x_gpio_pdata,
 	},
 };
 
diff --git a/drivers/mfd/sh_mobile_sdhi.c b/drivers/mfd/sh_mobile_sdhi.c
index 0a7df44..53a6302 100644
--- a/drivers/mfd/sh_mobile_sdhi.c
+++ b/drivers/mfd/sh_mobile_sdhi.c
@@ -146,9 +146,7 @@
 	}
 
 	memcpy(&priv->cell_mmc, &sh_mobile_sdhi_cell, sizeof(priv->cell_mmc));
-	priv->cell_mmc.driver_data = mmc_data;
-	priv->cell_mmc.platform_data = &priv->cell_mmc;
-	priv->cell_mmc.data_size = sizeof(priv->cell_mmc);
+	priv->cell_mmc.mfd_data = mmc_data;
 
 	platform_set_drvdata(pdev, priv);
 
diff --git a/drivers/mfd/t7l66xb.c b/drivers/mfd/t7l66xb.c
index 9caeb4a..af57fc7 100644
--- a/drivers/mfd/t7l66xb.c
+++ b/drivers/mfd/t7l66xb.c
@@ -170,7 +170,7 @@
 		.name = "tmio-mmc",
 		.enable = t7l66xb_mmc_enable,
 		.disable = t7l66xb_mmc_disable,
-		.driver_data = &t7166xb_mmc_data,
+		.mfd_data = &t7166xb_mmc_data,
 		.num_resources = ARRAY_SIZE(t7l66xb_mmc_resources),
 		.resources = t7l66xb_mmc_resources,
 	},
@@ -383,16 +383,7 @@
 
 	t7l66xb_attach_irq(dev);
 
-	t7l66xb_cells[T7L66XB_CELL_NAND].driver_data = pdata->nand_data;
-	t7l66xb_cells[T7L66XB_CELL_NAND].platform_data =
-		&t7l66xb_cells[T7L66XB_CELL_NAND];
-	t7l66xb_cells[T7L66XB_CELL_NAND].data_size =
-		sizeof(t7l66xb_cells[T7L66XB_CELL_NAND]);
-
-	t7l66xb_cells[T7L66XB_CELL_MMC].platform_data =
-		&t7l66xb_cells[T7L66XB_CELL_MMC];
-	t7l66xb_cells[T7L66XB_CELL_MMC].data_size =
-		sizeof(t7l66xb_cells[T7L66XB_CELL_MMC]);
+	t7l66xb_cells[T7L66XB_CELL_NAND].mfd_data = pdata->nand_data;
 
 	ret = mfd_add_devices(&dev->dev, dev->id,
 			      t7l66xb_cells, ARRAY_SIZE(t7l66xb_cells),
diff --git a/drivers/mfd/tc6387xb.c b/drivers/mfd/tc6387xb.c
index 6315f63..b006f7c 100644
--- a/drivers/mfd/tc6387xb.c
+++ b/drivers/mfd/tc6387xb.c
@@ -131,7 +131,7 @@
 		.name = "tmio-mmc",
 		.enable = tc6387xb_mmc_enable,
 		.disable = tc6387xb_mmc_disable,
-		.driver_data = &tc6387xb_mmc_data,
+		.mfd_data = &tc6387xb_mmc_data,
 		.num_resources = ARRAY_SIZE(tc6387xb_mmc_resources),
 		.resources = tc6387xb_mmc_resources,
 	},
@@ -190,11 +190,6 @@
 
 	printk(KERN_INFO "Toshiba tc6387xb initialised\n");
 
-	tc6387xb_cells[TC6387XB_CELL_MMC].platform_data =
-		&tc6387xb_cells[TC6387XB_CELL_MMC];
-	tc6387xb_cells[TC6387XB_CELL_MMC].data_size =
-		sizeof(tc6387xb_cells[TC6387XB_CELL_MMC]);
-
 	ret = mfd_add_devices(&dev->dev, dev->id, tc6387xb_cells,
 			      ARRAY_SIZE(tc6387xb_cells), iomem, irq);
 
diff --git a/drivers/mfd/tc6393xb.c b/drivers/mfd/tc6393xb.c
index 9a23863..3d62ded 100644
--- a/drivers/mfd/tc6393xb.c
+++ b/drivers/mfd/tc6393xb.c
@@ -393,7 +393,7 @@
 		.name = "tmio-mmc",
 		.enable = tc6393xb_mmc_enable,
 		.resume = tc6393xb_mmc_resume,
-		.driver_data = &tc6393xb_mmc_data,
+		.mfd_data = &tc6393xb_mmc_data,
 		.num_resources = ARRAY_SIZE(tc6393xb_mmc_resources),
 		.resources = tc6393xb_mmc_resources,
 	},
@@ -693,27 +693,8 @@
 			goto err_setup;
 	}
 
-	tc6393xb_cells[TC6393XB_CELL_NAND].driver_data = tcpd->nand_data;
-	tc6393xb_cells[TC6393XB_CELL_NAND].platform_data =
-		&tc6393xb_cells[TC6393XB_CELL_NAND];
-	tc6393xb_cells[TC6393XB_CELL_NAND].data_size =
-		sizeof(tc6393xb_cells[TC6393XB_CELL_NAND]);
-
-	tc6393xb_cells[TC6393XB_CELL_MMC].platform_data =
-		&tc6393xb_cells[TC6393XB_CELL_MMC];
-	tc6393xb_cells[TC6393XB_CELL_MMC].data_size =
-		sizeof(tc6393xb_cells[TC6393XB_CELL_MMC]);
-
-	tc6393xb_cells[TC6393XB_CELL_OHCI].platform_data =
-		&tc6393xb_cells[TC6393XB_CELL_OHCI];
-	tc6393xb_cells[TC6393XB_CELL_OHCI].data_size =
-		sizeof(tc6393xb_cells[TC6393XB_CELL_OHCI]);
-
-	tc6393xb_cells[TC6393XB_CELL_FB].driver_data = tcpd->fb_data;
-	tc6393xb_cells[TC6393XB_CELL_FB].platform_data =
-		&tc6393xb_cells[TC6393XB_CELL_FB];
-	tc6393xb_cells[TC6393XB_CELL_FB].data_size =
-		sizeof(tc6393xb_cells[TC6393XB_CELL_FB]);
+	tc6393xb_cells[TC6393XB_CELL_NAND].mfd_data = tcpd->nand_data;
+	tc6393xb_cells[TC6393XB_CELL_FB].mfd_data = tcpd->fb_data;
 
 	ret = mfd_add_devices(&dev->dev, dev->id,
 			tc6393xb_cells, ARRAY_SIZE(tc6393xb_cells),
diff --git a/drivers/mfd/timberdale.c b/drivers/mfd/timberdale.c
index 6ad8a7f..94c6c8a 100644
--- a/drivers/mfd/timberdale.c
+++ b/drivers/mfd/timberdale.c
@@ -384,8 +384,7 @@
 		.name = "timb-dma",
 		.num_resources = ARRAY_SIZE(timberdale_dma_resources),
 		.resources = timberdale_dma_resources,
-		.platform_data = &timb_dma_platform_data,
-		.data_size = sizeof(timb_dma_platform_data),
+		.mfd_data = &timb_dma_platform_data,
 	},
 	{
 		.name = "timb-uart",
@@ -396,43 +395,37 @@
 		.name = "xiic-i2c",
 		.num_resources = ARRAY_SIZE(timberdale_xiic_resources),
 		.resources = timberdale_xiic_resources,
-		.platform_data = &timberdale_xiic_platform_data,
-		.data_size = sizeof(timberdale_xiic_platform_data),
+		.mfd_data = &timberdale_xiic_platform_data,
 	},
 	{
 		.name = "timb-gpio",
 		.num_resources = ARRAY_SIZE(timberdale_gpio_resources),
 		.resources = timberdale_gpio_resources,
-		.platform_data = &timberdale_gpio_platform_data,
-		.data_size = sizeof(timberdale_gpio_platform_data),
+		.mfd_data = &timberdale_gpio_platform_data,
 	},
 	{
 		.name = "timb-video",
 		.num_resources = ARRAY_SIZE(timberdale_video_resources),
 		.resources = timberdale_video_resources,
-		.platform_data = &timberdale_video_platform_data,
-		.data_size = sizeof(timberdale_video_platform_data),
+		.mfd_data = &timberdale_video_platform_data,
 	},
 	{
 		.name = "timb-radio",
 		.num_resources = ARRAY_SIZE(timberdale_radio_resources),
 		.resources = timberdale_radio_resources,
-		.platform_data = &timberdale_radio_platform_data,
-		.data_size = sizeof(timberdale_radio_platform_data),
+		.mfd_data = &timberdale_radio_platform_data,
 	},
 	{
 		.name = "xilinx_spi",
 		.num_resources = ARRAY_SIZE(timberdale_spi_resources),
 		.resources = timberdale_spi_resources,
-		.platform_data = &timberdale_xspi_platform_data,
-		.data_size = sizeof(timberdale_xspi_platform_data),
+		.mfd_data = &timberdale_xspi_platform_data,
 	},
 	{
 		.name = "ks8842",
 		.num_resources = ARRAY_SIZE(timberdale_eth_resources),
 		.resources = timberdale_eth_resources,
-		.platform_data = &timberdale_ks8842_platform_data,
-		.data_size = sizeof(timberdale_ks8842_platform_data)
+		.mfd_data = &timberdale_ks8842_platform_data,
 	},
 };
 
@@ -441,8 +434,7 @@
 		.name = "timb-dma",
 		.num_resources = ARRAY_SIZE(timberdale_dma_resources),
 		.resources = timberdale_dma_resources,
-		.platform_data = &timb_dma_platform_data,
-		.data_size = sizeof(timb_dma_platform_data),
+		.mfd_data = &timb_dma_platform_data,
 	},
 	{
 		.name = "timb-uart",
@@ -458,15 +450,13 @@
 		.name = "xiic-i2c",
 		.num_resources = ARRAY_SIZE(timberdale_xiic_resources),
 		.resources = timberdale_xiic_resources,
-		.platform_data = &timberdale_xiic_platform_data,
-		.data_size = sizeof(timberdale_xiic_platform_data),
+		.mfd_data = &timberdale_xiic_platform_data,
 	},
 	{
 		.name = "timb-gpio",
 		.num_resources = ARRAY_SIZE(timberdale_gpio_resources),
 		.resources = timberdale_gpio_resources,
-		.platform_data = &timberdale_gpio_platform_data,
-		.data_size = sizeof(timberdale_gpio_platform_data),
+		.mfd_data = &timberdale_gpio_platform_data,
 	},
 	{
 		.name = "timb-mlogicore",
@@ -477,29 +467,25 @@
 		.name = "timb-video",
 		.num_resources = ARRAY_SIZE(timberdale_video_resources),
 		.resources = timberdale_video_resources,
-		.platform_data = &timberdale_video_platform_data,
-		.data_size = sizeof(timberdale_video_platform_data),
+		.mfd_data = &timberdale_video_platform_data,
 	},
 	{
 		.name = "timb-radio",
 		.num_resources = ARRAY_SIZE(timberdale_radio_resources),
 		.resources = timberdale_radio_resources,
-		.platform_data = &timberdale_radio_platform_data,
-		.data_size = sizeof(timberdale_radio_platform_data),
+		.mfd_data = &timberdale_radio_platform_data,
 	},
 	{
 		.name = "xilinx_spi",
 		.num_resources = ARRAY_SIZE(timberdale_spi_resources),
 		.resources = timberdale_spi_resources,
-		.platform_data = &timberdale_xspi_platform_data,
-		.data_size = sizeof(timberdale_xspi_platform_data),
+		.mfd_data = &timberdale_xspi_platform_data,
 	},
 	{
 		.name = "ks8842",
 		.num_resources = ARRAY_SIZE(timberdale_eth_resources),
 		.resources = timberdale_eth_resources,
-		.platform_data = &timberdale_ks8842_platform_data,
-		.data_size = sizeof(timberdale_ks8842_platform_data)
+		.mfd_data = &timberdale_ks8842_platform_data,
 	},
 };
 
@@ -508,8 +494,7 @@
 		.name = "timb-dma",
 		.num_resources = ARRAY_SIZE(timberdale_dma_resources),
 		.resources = timberdale_dma_resources,
-		.platform_data = &timb_dma_platform_data,
-		.data_size = sizeof(timb_dma_platform_data),
+		.mfd_data = &timb_dma_platform_data,
 	},
 	{
 		.name = "timb-uart",
@@ -520,36 +505,31 @@
 		.name = "xiic-i2c",
 		.num_resources = ARRAY_SIZE(timberdale_xiic_resources),
 		.resources = timberdale_xiic_resources,
-		.platform_data = &timberdale_xiic_platform_data,
-		.data_size = sizeof(timberdale_xiic_platform_data),
+		.mfd_data = &timberdale_xiic_platform_data,
 	},
 	{
 		.name = "timb-gpio",
 		.num_resources = ARRAY_SIZE(timberdale_gpio_resources),
 		.resources = timberdale_gpio_resources,
-		.platform_data = &timberdale_gpio_platform_data,
-		.data_size = sizeof(timberdale_gpio_platform_data),
+		.mfd_data = &timberdale_gpio_platform_data,
 	},
 	{
 		.name = "timb-video",
 		.num_resources = ARRAY_SIZE(timberdale_video_resources),
 		.resources = timberdale_video_resources,
-		.platform_data = &timberdale_video_platform_data,
-		.data_size = sizeof(timberdale_video_platform_data),
+		.mfd_data = &timberdale_video_platform_data,
 	},
 	{
 		.name = "timb-radio",
 		.num_resources = ARRAY_SIZE(timberdale_radio_resources),
 		.resources = timberdale_radio_resources,
-		.platform_data = &timberdale_radio_platform_data,
-		.data_size = sizeof(timberdale_radio_platform_data),
+		.mfd_data = &timberdale_radio_platform_data,
 	},
 	{
 		.name = "xilinx_spi",
 		.num_resources = ARRAY_SIZE(timberdale_spi_resources),
 		.resources = timberdale_spi_resources,
-		.platform_data = &timberdale_xspi_platform_data,
-		.data_size = sizeof(timberdale_xspi_platform_data),
+		.mfd_data = &timberdale_xspi_platform_data,
 	},
 };
 
@@ -558,8 +538,7 @@
 		.name = "timb-dma",
 		.num_resources = ARRAY_SIZE(timberdale_dma_resources),
 		.resources = timberdale_dma_resources,
-		.platform_data = &timb_dma_platform_data,
-		.data_size = sizeof(timb_dma_platform_data),
+		.mfd_data = &timb_dma_platform_data,
 	},
 	{
 		.name = "timb-uart",
@@ -570,43 +549,37 @@
 		.name = "ocores-i2c",
 		.num_resources = ARRAY_SIZE(timberdale_ocores_resources),
 		.resources = timberdale_ocores_resources,
-		.platform_data = &timberdale_ocores_platform_data,
-		.data_size = sizeof(timberdale_ocores_platform_data),
+		.mfd_data = &timberdale_ocores_platform_data,
 	},
 	{
 		.name = "timb-gpio",
 		.num_resources = ARRAY_SIZE(timberdale_gpio_resources),
 		.resources = timberdale_gpio_resources,
-		.platform_data = &timberdale_gpio_platform_data,
-		.data_size = sizeof(timberdale_gpio_platform_data),
+		.mfd_data = &timberdale_gpio_platform_data,
 	},
 	{
 		.name = "timb-video",
 		.num_resources = ARRAY_SIZE(timberdale_video_resources),
 		.resources = timberdale_video_resources,
-		.platform_data = &timberdale_video_platform_data,
-		.data_size = sizeof(timberdale_video_platform_data),
+		.mfd_data = &timberdale_video_platform_data,
 	},
 	{
 		.name = "timb-radio",
 		.num_resources = ARRAY_SIZE(timberdale_radio_resources),
 		.resources = timberdale_radio_resources,
-		.platform_data = &timberdale_radio_platform_data,
-		.data_size = sizeof(timberdale_radio_platform_data),
+		.mfd_data = &timberdale_radio_platform_data,
 	},
 	{
 		.name = "xilinx_spi",
 		.num_resources = ARRAY_SIZE(timberdale_spi_resources),
 		.resources = timberdale_spi_resources,
-		.platform_data = &timberdale_xspi_platform_data,
-		.data_size = sizeof(timberdale_xspi_platform_data),
+		.mfd_data = &timberdale_xspi_platform_data,
 	},
 	{
 		.name = "ks8842",
 		.num_resources = ARRAY_SIZE(timberdale_eth_resources),
 		.resources = timberdale_eth_resources,
-		.platform_data = &timberdale_ks8842_platform_data,
-		.data_size = sizeof(timberdale_ks8842_platform_data)
+		.mfd_data = &timberdale_ks8842_platform_data,
 	},
 };
 
diff --git a/drivers/mfd/tps6105x.c b/drivers/mfd/tps6105x.c
new file mode 100644
index 0000000..46d8205
--- /dev/null
+++ b/drivers/mfd/tps6105x.c
@@ -0,0 +1,246 @@
+/*
+ * Core driver for TPS61050/61052 boost converters, used for while LED
+ * driving, audio power amplification, white LED flash, and generic
+ * boost conversion. Additionally it provides a 1-bit GPIO pin (out or in)
+ * and a flash synchronization pin to synchronize flash events when used as
+ * flashgun.
+ *
+ * Copyright (C) 2011 ST-Ericsson SA
+ * Written on behalf of Linaro for ST-Ericsson
+ *
+ * Author: Linus Walleij <linus.walleij@linaro.org>
+ *
+ * License terms: GNU General Public License (GPL) version 2
+ */
+
+#include <linux/module.h>
+#include <linux/init.h>
+#include <linux/i2c.h>
+#include <linux/mutex.h>
+#include <linux/gpio.h>
+#include <linux/spinlock.h>
+#include <linux/slab.h>
+#include <linux/err.h>
+#include <linux/regulator/driver.h>
+#include <linux/mfd/core.h>
+#include <linux/mfd/tps6105x.h>
+
+int tps6105x_set(struct tps6105x *tps6105x, u8 reg, u8 value)
+{
+	int ret;
+
+	ret = mutex_lock_interruptible(&tps6105x->lock);
+	if (ret)
+		return ret;
+	ret = i2c_smbus_write_byte_data(tps6105x->client, reg, value);
+	mutex_unlock(&tps6105x->lock);
+	if (ret < 0)
+		return ret;
+
+	return 0;
+}
+EXPORT_SYMBOL(tps6105x_set);
+
+int tps6105x_get(struct tps6105x *tps6105x, u8 reg, u8 *buf)
+{
+	int ret;
+
+	ret = mutex_lock_interruptible(&tps6105x->lock);
+	if (ret)
+		return ret;
+	ret = i2c_smbus_read_byte_data(tps6105x->client, reg);
+	mutex_unlock(&tps6105x->lock);
+	if (ret < 0)
+		return ret;
+
+	*buf = ret;
+	return 0;
+}
+EXPORT_SYMBOL(tps6105x_get);
+
+/*
+ * Masks off the bits in the mask and sets the bits in the bitvalues
+ * parameter in one atomic operation
+ */
+int tps6105x_mask_and_set(struct tps6105x *tps6105x, u8 reg,
+			  u8 bitmask, u8 bitvalues)
+{
+	int ret;
+	u8 regval;
+
+	ret = mutex_lock_interruptible(&tps6105x->lock);
+	if (ret)
+		return ret;
+	ret = i2c_smbus_read_byte_data(tps6105x->client, reg);
+	if (ret < 0)
+		goto fail;
+	regval = ret;
+	regval = (~bitmask & regval) | (bitmask & bitvalues);
+	ret = i2c_smbus_write_byte_data(tps6105x->client, reg, regval);
+fail:
+	mutex_unlock(&tps6105x->lock);
+	if (ret < 0)
+		return ret;
+
+	return 0;
+}
+EXPORT_SYMBOL(tps6105x_mask_and_set);
+
+static int __devinit tps6105x_startup(struct tps6105x *tps6105x)
+{
+	int ret;
+	u8 regval;
+
+	ret = tps6105x_get(tps6105x, TPS6105X_REG_0, &regval);
+	if (ret)
+		return ret;
+	switch (regval >> TPS6105X_REG0_MODE_SHIFT) {
+	case TPS6105X_REG0_MODE_SHUTDOWN:
+		dev_info(&tps6105x->client->dev,
+			 "TPS6105x found in SHUTDOWN mode\n");
+		break;
+	case TPS6105X_REG0_MODE_TORCH:
+		dev_info(&tps6105x->client->dev,
+			 "TPS6105x found in TORCH mode\n");
+		break;
+	case TPS6105X_REG0_MODE_TORCH_FLASH:
+		dev_info(&tps6105x->client->dev,
+			 "TPS6105x found in FLASH mode\n");
+		break;
+	case TPS6105X_REG0_MODE_VOLTAGE:
+		dev_info(&tps6105x->client->dev,
+			 "TPS6105x found in VOLTAGE mode\n");
+		break;
+	default:
+		break;
+	}
+
+	return ret;
+}
+
+/*
+ * MFD cells - we have one cell which is selected operation
+ * mode, and we always have a GPIO cell.
+ */
+static struct mfd_cell tps6105x_cells[] = {
+	{
+		/* name will be runtime assigned */
+		.id = -1,
+	},
+	{
+		.name = "tps6105x-gpio",
+		.id = -1,
+	},
+};
+
+static int __devinit tps6105x_probe(struct i2c_client *client,
+			const struct i2c_device_id *id)
+{
+	struct tps6105x			*tps6105x;
+	struct tps6105x_platform_data	*pdata;
+	int ret;
+	int i;
+
+	tps6105x = kmalloc(sizeof(*tps6105x), GFP_KERNEL);
+	if (!tps6105x)
+		return -ENOMEM;
+
+	i2c_set_clientdata(client, tps6105x);
+	tps6105x->client = client;
+	pdata = client->dev.platform_data;
+	tps6105x->pdata = pdata;
+	mutex_init(&tps6105x->lock);
+
+	ret = tps6105x_startup(tps6105x);
+	if (ret) {
+		dev_err(&client->dev, "chip initialization failed\n");
+		goto fail;
+	}
+
+	/* Remove warning texts when you implement new cell drivers */
+	switch (pdata->mode) {
+	case TPS6105X_MODE_SHUTDOWN:
+		dev_info(&client->dev,
+			 "present, not used for anything, only GPIO\n");
+		break;
+	case TPS6105X_MODE_TORCH:
+		tps6105x_cells[0].name = "tps6105x-leds";
+		dev_warn(&client->dev,
+			 "torch mode is unsupported\n");
+		break;
+	case TPS6105X_MODE_TORCH_FLASH:
+		tps6105x_cells[0].name = "tps6105x-flash";
+		dev_warn(&client->dev,
+			 "flash mode is unsupported\n");
+		break;
+	case TPS6105X_MODE_VOLTAGE:
+		tps6105x_cells[0].name ="tps6105x-regulator";
+		break;
+	default:
+		break;
+	}
+
+	/* Set up and register the platform devices. */
+	for (i = 0; i < ARRAY_SIZE(tps6105x_cells); i++) {
+		/* One state holder for all drivers, this is simple */
+		tps6105x_cells[i].mfd_data = tps6105x;
+	}
+
+	ret = mfd_add_devices(&client->dev, 0, tps6105x_cells,
+		ARRAY_SIZE(tps6105x_cells), NULL, 0);
+	if (ret)
+		goto fail;
+
+	return 0;
+
+fail:
+	kfree(tps6105x);
+	return ret;
+}
+
+static int __devexit tps6105x_remove(struct i2c_client *client)
+{
+	struct tps6105x *tps6105x = i2c_get_clientdata(client);
+
+	mfd_remove_devices(&client->dev);
+
+	/* Put chip in shutdown mode */
+	tps6105x_mask_and_set(tps6105x, TPS6105X_REG_0,
+		TPS6105X_REG0_MODE_MASK,
+		TPS6105X_MODE_SHUTDOWN << TPS6105X_REG0_MODE_SHIFT);
+
+	kfree(tps6105x);
+	return 0;
+}
+
+static const struct i2c_device_id tps6105x_id[] = {
+	{ "tps61050", 0 },
+	{ "tps61052", 0 },
+	{ }
+};
+MODULE_DEVICE_TABLE(i2c, tps6105x_id);
+
+static struct i2c_driver tps6105x_driver = {
+	.driver = {
+		.name	= "tps6105x",
+	},
+	.probe		= tps6105x_probe,
+	.remove		= __devexit_p(tps6105x_remove),
+	.id_table	= tps6105x_id,
+};
+
+static int __init tps6105x_init(void)
+{
+	return i2c_add_driver(&tps6105x_driver);
+}
+subsys_initcall(tps6105x_init);
+
+static void __exit tps6105x_exit(void)
+{
+	i2c_del_driver(&tps6105x_driver);
+}
+module_exit(tps6105x_exit);
+
+MODULE_AUTHOR("Linus Walleij");
+MODULE_DESCRIPTION("TPS6105x White LED Boost Converter Driver");
+MODULE_LICENSE("GPL v2");
diff --git a/drivers/mfd/tps6586x.c b/drivers/mfd/tps6586x.c
index e9018d1..0aa9186 100644
--- a/drivers/mfd/tps6586x.c
+++ b/drivers/mfd/tps6586x.c
@@ -288,12 +288,10 @@
 	return tps6586x_update(tps6586x->dev, TPS6586X_GPIOSET1, val, mask);
 }
 
-static void tps6586x_gpio_init(struct tps6586x *tps6586x, int gpio_base)
+static int tps6586x_gpio_init(struct tps6586x *tps6586x, int gpio_base)
 {
-	int ret;
-
 	if (!gpio_base)
-		return;
+		return 0;
 
 	tps6586x->gpio.owner		= THIS_MODULE;
 	tps6586x->gpio.label		= tps6586x->client->name;
@@ -307,9 +305,7 @@
 	tps6586x->gpio.set		= tps6586x_gpio_set;
 	tps6586x->gpio.get		= tps6586x_gpio_get;
 
-	ret = gpiochip_add(&tps6586x->gpio);
-	if (ret)
-		dev_warn(tps6586x->dev, "GPIO registration failed: %d\n", ret);
+	return gpiochip_add(&tps6586x->gpio);
 }
 
 static int __remove_subdev(struct device *dev, void *unused)
@@ -517,17 +513,28 @@
 		}
 	}
 
+	ret = tps6586x_gpio_init(tps6586x, pdata->gpio_base);
+	if (ret) {
+		dev_err(&client->dev, "GPIO registration failed: %d\n", ret);
+		goto err_gpio_init;
+	}
+
 	ret = tps6586x_add_subdevs(tps6586x, pdata);
 	if (ret) {
 		dev_err(&client->dev, "add devices failed: %d\n", ret);
 		goto err_add_devs;
 	}
 
-	tps6586x_gpio_init(tps6586x, pdata->gpio_base);
-
 	return 0;
 
 err_add_devs:
+	if (pdata->gpio_base) {
+		ret = gpiochip_remove(&tps6586x->gpio);
+		if (ret)
+			dev_err(&client->dev, "Can't remove gpio chip: %d\n",
+				ret);
+	}
+err_gpio_init:
 	if (client->irq)
 		free_irq(client->irq, tps6586x);
 err_irq_init:
@@ -587,4 +594,3 @@
 MODULE_DESCRIPTION("TPS6586X core driver");
 MODULE_AUTHOR("Mike Rapoport <mike@compulab.co.il>");
 MODULE_LICENSE("GPL");
-
diff --git a/drivers/mfd/twl-core.c b/drivers/mfd/twl-core.c
index a35fa7d..960b5be 100644
--- a/drivers/mfd/twl-core.c
+++ b/drivers/mfd/twl-core.c
@@ -721,13 +721,13 @@
 
 	}
 
-	if (twl_has_watchdog()) {
+	if (twl_has_watchdog() && twl_class_is_4030()) {
 		child = add_child(0, "twl4030_wdt", NULL, 0, false, 0, 0);
 		if (IS_ERR(child))
 			return PTR_ERR(child);
 	}
 
-	if (twl_has_pwrbutton()) {
+	if (twl_has_pwrbutton() && twl_class_is_4030()) {
 		child = add_child(1, "twl4030_pwrbutton",
 				NULL, 0, true, pdata->irq_base + 8 + 0, 0);
 		if (IS_ERR(child))
@@ -864,6 +864,10 @@
 		child = add_regulator(TWL6030_REG_VAUX3_6030, pdata->vaux3);
 		if (IS_ERR(child))
 			return PTR_ERR(child);
+
+		child = add_regulator(TWL6030_REG_CLK32KG, pdata->clk32kg);
+		if (IS_ERR(child))
+			return PTR_ERR(child);
 	}
 
 	if (twl_has_bci() && pdata->bci &&
diff --git a/drivers/mfd/twl4030-codec.c b/drivers/mfd/twl4030-codec.c
index 9a4b196..c02fded 100644
--- a/drivers/mfd/twl4030-codec.c
+++ b/drivers/mfd/twl4030-codec.c
@@ -208,15 +208,13 @@
 	if (pdata->audio) {
 		cell = &codec->cells[childs];
 		cell->name = "twl4030-codec";
-		cell->platform_data = pdata->audio;
-		cell->data_size = sizeof(*pdata->audio);
+		cell->mfd_data = pdata->audio;
 		childs++;
 	}
 	if (pdata->vibra) {
 		cell = &codec->cells[childs];
 		cell->name = "twl4030-vibra";
-		cell->platform_data = pdata->vibra;
-		cell->data_size = sizeof(*pdata->vibra);
+		cell->mfd_data = pdata->vibra;
 		childs++;
 	}
 
diff --git a/drivers/mfd/twl4030-madc.c b/drivers/mfd/twl4030-madc.c
new file mode 100644
index 0000000..3941ddc
--- /dev/null
+++ b/drivers/mfd/twl4030-madc.c
@@ -0,0 +1,802 @@
+/*
+ *
+ * TWL4030 MADC module driver-This driver monitors the real time
+ * conversion of analog signals like battery temperature,
+ * battery type, battery level etc.
+ *
+ * Copyright (C) 2011 Texas Instruments Incorporated - http://www.ti.com/
+ * J Keerthy <j-keerthy@ti.com>
+ *
+ * Based on twl4030-madc.c
+ * Copyright (C) 2008 Nokia Corporation
+ * Mikko Ylinen <mikko.k.ylinen@nokia.com>
+ *
+ * Amit Kucheria <amit.kucheria@canonical.com>
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License
+ * version 2 as published by the Free Software Foundation.
+ *
+ * This program is distributed in the hope that it will be useful, but
+ * WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the GNU
+ * General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA
+ * 02110-1301 USA
+ *
+ */
+
+#include <linux/init.h>
+#include <linux/device.h>
+#include <linux/interrupt.h>
+#include <linux/kernel.h>
+#include <linux/delay.h>
+#include <linux/platform_device.h>
+#include <linux/slab.h>
+#include <linux/i2c/twl.h>
+#include <linux/i2c/twl4030-madc.h>
+#include <linux/module.h>
+#include <linux/stddef.h>
+#include <linux/mutex.h>
+#include <linux/bitops.h>
+#include <linux/jiffies.h>
+#include <linux/types.h>
+#include <linux/gfp.h>
+#include <linux/err.h>
+
+/*
+ * struct twl4030_madc_data - a container for madc info
+ * @dev - pointer to device structure for madc
+ * @lock - mutex protecting this data structure
+ * @requests - Array of request struct corresponding to SW1, SW2 and RT
+ * @imr - Interrupt mask register of MADC
+ * @isr - Interrupt status register of MADC
+ */
+struct twl4030_madc_data {
+	struct device *dev;
+	struct mutex lock;	/* mutex protecting this data structure */
+	struct twl4030_madc_request requests[TWL4030_MADC_NUM_METHODS];
+	int imr;
+	int isr;
+};
+
+static struct twl4030_madc_data *twl4030_madc;
+
+struct twl4030_prescale_divider_ratios {
+	s16 numerator;
+	s16 denominator;
+};
+
+static const struct twl4030_prescale_divider_ratios
+twl4030_divider_ratios[16] = {
+	{1, 1},		/* CHANNEL 0 No Prescaler */
+	{1, 1},		/* CHANNEL 1 No Prescaler */
+	{6, 10},	/* CHANNEL 2 */
+	{6, 10},	/* CHANNEL 3 */
+	{6, 10},	/* CHANNEL 4 */
+	{6, 10},	/* CHANNEL 5 */
+	{6, 10},	/* CHANNEL 6 */
+	{6, 10},	/* CHANNEL 7 */
+	{3, 14},	/* CHANNEL 8 */
+	{1, 3},		/* CHANNEL 9 */
+	{1, 1},		/* CHANNEL 10 No Prescaler */
+	{15, 100},	/* CHANNEL 11 */
+	{1, 4},		/* CHANNEL 12 */
+	{1, 1},		/* CHANNEL 13 Reserved channels */
+	{1, 1},		/* CHANNEL 14 Reseved channels */
+	{5, 11},	/* CHANNEL 15 */
+};
+
+
+/*
+ * Conversion table from -3 to 55 degree Celcius
+ */
+static int therm_tbl[] = {
+30800,	29500,	28300,	27100,
+26000,	24900,	23900,	22900,	22000,	21100,	20300,	19400,	18700,	17900,
+17200,	16500,	15900,	15300,	14700,	14100,	13600,	13100,	12600,	12100,
+11600,	11200,	10800,	10400,	10000,	9630,	9280,	8950,	8620,	8310,
+8020,	7730,	7460,	7200,	6950,	6710,	6470,	6250,	6040,	5830,
+5640,	5450,	5260,	5090,	4920,	4760,	4600,	4450,	4310,	4170,
+4040,	3910,	3790,	3670,	3550
+};
+
+/*
+ * Structure containing the registers
+ * of different conversion methods supported by MADC.
+ * Hardware or RT real time conversion request initiated by external host
+ * processor for RT Signal conversions.
+ * External host processors can also request for non RT conversions
+ * SW1 and SW2 software conversions also called asynchronous or GPC request.
+ */
+static
+const struct twl4030_madc_conversion_method twl4030_conversion_methods[] = {
+	[TWL4030_MADC_RT] = {
+			     .sel = TWL4030_MADC_RTSELECT_LSB,
+			     .avg = TWL4030_MADC_RTAVERAGE_LSB,
+			     .rbase = TWL4030_MADC_RTCH0_LSB,
+			     },
+	[TWL4030_MADC_SW1] = {
+			      .sel = TWL4030_MADC_SW1SELECT_LSB,
+			      .avg = TWL4030_MADC_SW1AVERAGE_LSB,
+			      .rbase = TWL4030_MADC_GPCH0_LSB,
+			      .ctrl = TWL4030_MADC_CTRL_SW1,
+			      },
+	[TWL4030_MADC_SW2] = {
+			      .sel = TWL4030_MADC_SW2SELECT_LSB,
+			      .avg = TWL4030_MADC_SW2AVERAGE_LSB,
+			      .rbase = TWL4030_MADC_GPCH0_LSB,
+			      .ctrl = TWL4030_MADC_CTRL_SW2,
+			      },
+};
+
+/*
+ * Function to read a particular channel value.
+ * @madc - pointer to struct twl4030_madc_data
+ * @reg - lsb of ADC Channel
+ * If the i2c read fails it returns an error else returns 0.
+ */
+static int twl4030_madc_channel_raw_read(struct twl4030_madc_data *madc, u8 reg)
+{
+	u8 msb, lsb;
+	int ret;
+	/*
+	 * For each ADC channel, we have MSB and LSB register pair. MSB address
+	 * is always LSB address+1. reg parameter is the address of LSB register
+	 */
+	ret = twl_i2c_read_u8(TWL4030_MODULE_MADC, &msb, reg + 1);
+	if (ret) {
+		dev_err(madc->dev, "unable to read MSB register 0x%X\n",
+			reg + 1);
+		return ret;
+	}
+	ret = twl_i2c_read_u8(TWL4030_MODULE_MADC, &lsb, reg);
+	if (ret) {
+		dev_err(madc->dev, "unable to read LSB register 0x%X\n", reg);
+		return ret;
+	}
+
+	return (int)(((msb << 8) | lsb) >> 6);
+}
+
+/*
+ * Return battery temperature
+ * Or < 0 on failure.
+ */
+static int twl4030battery_temperature(int raw_volt)
+{
+	u8 val;
+	int temp, curr, volt, res, ret;
+
+	volt = (raw_volt * TEMP_STEP_SIZE) / TEMP_PSR_R;
+	/* Getting and calculating the supply current in micro ampers */
+	ret = twl_i2c_read_u8(TWL4030_MODULE_MAIN_CHARGE, &val,
+		REG_BCICTL2);
+	if (ret < 0)
+		return ret;
+	curr = ((val & TWL4030_BCI_ITHEN) + 1) * 10;
+	/* Getting and calculating the thermistor resistance in ohms */
+	res = volt * 1000 / curr;
+	/* calculating temperature */
+	for (temp = 58; temp >= 0; temp--) {
+		int actual = therm_tbl[temp];
+
+		if ((actual - res) >= 0)
+			break;
+	}
+
+	return temp + 1;
+}
+
+static int twl4030battery_current(int raw_volt)
+{
+	int ret;
+	u8 val;
+
+	ret = twl_i2c_read_u8(TWL4030_MODULE_MAIN_CHARGE, &val,
+		TWL4030_BCI_BCICTL1);
+	if (ret)
+		return ret;
+	if (val & TWL4030_BCI_CGAIN) /* slope of 0.44 mV/mA */
+		return (raw_volt * CURR_STEP_SIZE) / CURR_PSR_R1;
+	else /* slope of 0.88 mV/mA */
+		return (raw_volt * CURR_STEP_SIZE) / CURR_PSR_R2;
+}
+/*
+ * Function to read channel values
+ * @madc - pointer to twl4030_madc_data struct
+ * @reg_base - Base address of the first channel
+ * @Channels - 16 bit bitmap. If the bit is set, channel value is read
+ * @buf - The channel values are stored here. if read fails error
+ * value is stored
+ * Returns the number of successfully read channels.
+ */
+static int twl4030_madc_read_channels(struct twl4030_madc_data *madc,
+				      u8 reg_base, unsigned
+						long channels, int *buf)
+{
+	int count = 0, count_req = 0, i;
+	u8 reg;
+
+	for_each_set_bit(i, &channels, TWL4030_MADC_MAX_CHANNELS) {
+		reg = reg_base + 2 * i;
+		buf[i] = twl4030_madc_channel_raw_read(madc, reg);
+		if (buf[i] < 0) {
+			dev_err(madc->dev,
+				"Unable to read register 0x%X\n", reg);
+			count_req++;
+			continue;
+		}
+		switch (i) {
+		case 10:
+			buf[i] = twl4030battery_current(buf[i]);
+			if (buf[i] < 0) {
+				dev_err(madc->dev, "err reading current\n");
+				count_req++;
+			} else {
+				count++;
+				buf[i] = buf[i] - 750;
+			}
+			break;
+		case 1:
+			buf[i] = twl4030battery_temperature(buf[i]);
+			if (buf[i] < 0) {
+				dev_err(madc->dev, "err reading temperature\n");
+				count_req++;
+			} else {
+				buf[i] -= 3;
+				count++;
+			}
+			break;
+		default:
+			count++;
+			/* Analog Input (V) = conv_result * step_size / R
+			 * conv_result = decimal value of 10-bit conversion
+			 *		 result
+			 * step size = 1.5 / (2 ^ 10 -1)
+			 * R = Prescaler ratio for input channels.
+			 * Result given in mV hence multiplied by 1000.
+			 */
+			buf[i] = (buf[i] * 3 * 1000 *
+				 twl4030_divider_ratios[i].denominator)
+				/ (2 * 1023 *
+				twl4030_divider_ratios[i].numerator);
+		}
+	}
+	if (count_req)
+		dev_err(madc->dev, "%d channel conversion failed\n", count_req);
+
+	return count;
+}
+
+/*
+ * Enables irq.
+ * @madc - pointer to twl4030_madc_data struct
+ * @id - irq number to be enabled
+ * can take one of TWL4030_MADC_RT, TWL4030_MADC_SW1, TWL4030_MADC_SW2
+ * corresponding to RT, SW1, SW2 conversion requests.
+ * If the i2c read fails it returns an error else returns 0.
+ */
+static int twl4030_madc_enable_irq(struct twl4030_madc_data *madc, u8 id)
+{
+	u8 val;
+	int ret;
+
+	ret = twl_i2c_read_u8(TWL4030_MODULE_MADC, &val, madc->imr);
+	if (ret) {
+		dev_err(madc->dev, "unable to read imr register 0x%X\n",
+			madc->imr);
+		return ret;
+	}
+	val &= ~(1 << id);
+	ret = twl_i2c_write_u8(TWL4030_MODULE_MADC, val, madc->imr);
+	if (ret) {
+		dev_err(madc->dev,
+			"unable to write imr register 0x%X\n", madc->imr);
+		return ret;
+
+	}
+
+	return 0;
+}
+
+/*
+ * Disables irq.
+ * @madc - pointer to twl4030_madc_data struct
+ * @id - irq number to be disabled
+ * can take one of TWL4030_MADC_RT, TWL4030_MADC_SW1, TWL4030_MADC_SW2
+ * corresponding to RT, SW1, SW2 conversion requests.
+ * Returns error if i2c read/write fails.
+ */
+static int twl4030_madc_disable_irq(struct twl4030_madc_data *madc, u8 id)
+{
+	u8 val;
+	int ret;
+
+	ret = twl_i2c_read_u8(TWL4030_MODULE_MADC, &val, madc->imr);
+	if (ret) {
+		dev_err(madc->dev, "unable to read imr register 0x%X\n",
+			madc->imr);
+		return ret;
+	}
+	val |= (1 << id);
+	ret = twl_i2c_write_u8(TWL4030_MODULE_MADC, val, madc->imr);
+	if (ret) {
+		dev_err(madc->dev,
+			"unable to write imr register 0x%X\n", madc->imr);
+		return ret;
+	}
+
+	return 0;
+}
+
+static irqreturn_t twl4030_madc_threaded_irq_handler(int irq, void *_madc)
+{
+	struct twl4030_madc_data *madc = _madc;
+	const struct twl4030_madc_conversion_method *method;
+	u8 isr_val, imr_val;
+	int i, len, ret;
+	struct twl4030_madc_request *r;
+
+	mutex_lock(&madc->lock);
+	ret = twl_i2c_read_u8(TWL4030_MODULE_MADC, &isr_val, madc->isr);
+	if (ret) {
+		dev_err(madc->dev, "unable to read isr register 0x%X\n",
+			madc->isr);
+		goto err_i2c;
+	}
+	ret = twl_i2c_read_u8(TWL4030_MODULE_MADC, &imr_val, madc->imr);
+	if (ret) {
+		dev_err(madc->dev, "unable to read imr register 0x%X\n",
+			madc->imr);
+		goto err_i2c;
+	}
+	isr_val &= ~imr_val;
+	for (i = 0; i < TWL4030_MADC_NUM_METHODS; i++) {
+		if (!(isr_val & (1 << i)))
+			continue;
+		ret = twl4030_madc_disable_irq(madc, i);
+		if (ret < 0)
+			dev_dbg(madc->dev, "Disable interrupt failed%d\n", i);
+		madc->requests[i].result_pending = 1;
+	}
+	for (i = 0; i < TWL4030_MADC_NUM_METHODS; i++) {
+		r = &madc->requests[i];
+		/* No pending results for this method, move to next one */
+		if (!r->result_pending)
+			continue;
+		method = &twl4030_conversion_methods[r->method];
+		/* Read results */
+		len = twl4030_madc_read_channels(madc, method->rbase,
+						 r->channels, r->rbuf);
+		/* Return results to caller */
+		if (r->func_cb != NULL) {
+			r->func_cb(len, r->channels, r->rbuf);
+			r->func_cb = NULL;
+		}
+		/* Free request */
+		r->result_pending = 0;
+		r->active = 0;
+	}
+	mutex_unlock(&madc->lock);
+
+	return IRQ_HANDLED;
+
+err_i2c:
+	/*
+	 * In case of error check whichever request is active
+	 * and service the same.
+	 */
+	for (i = 0; i < TWL4030_MADC_NUM_METHODS; i++) {
+		r = &madc->requests[i];
+		if (r->active == 0)
+			continue;
+		method = &twl4030_conversion_methods[r->method];
+		/* Read results */
+		len = twl4030_madc_read_channels(madc, method->rbase,
+						 r->channels, r->rbuf);
+		/* Return results to caller */
+		if (r->func_cb != NULL) {
+			r->func_cb(len, r->channels, r->rbuf);
+			r->func_cb = NULL;
+		}
+		/* Free request */
+		r->result_pending = 0;
+		r->active = 0;
+	}
+	mutex_unlock(&madc->lock);
+
+	return IRQ_HANDLED;
+}
+
+static int twl4030_madc_set_irq(struct twl4030_madc_data *madc,
+				struct twl4030_madc_request *req)
+{
+	struct twl4030_madc_request *p;
+	int ret;
+
+	p = &madc->requests[req->method];
+	memcpy(p, req, sizeof(*req));
+	ret = twl4030_madc_enable_irq(madc, req->method);
+	if (ret < 0) {
+		dev_err(madc->dev, "enable irq failed!!\n");
+		return ret;
+	}
+
+	return 0;
+}
+
+/*
+ * Function which enables the madc conversion
+ * by writing to the control register.
+ * @madc - pointer to twl4030_madc_data struct
+ * @conv_method - can be TWL4030_MADC_RT, TWL4030_MADC_SW2, TWL4030_MADC_SW1
+ * corresponding to RT SW1 or SW2 conversion methods.
+ * Returns 0 if succeeds else a negative error value
+ */
+static int twl4030_madc_start_conversion(struct twl4030_madc_data *madc,
+					 int conv_method)
+{
+	const struct twl4030_madc_conversion_method *method;
+	int ret = 0;
+	method = &twl4030_conversion_methods[conv_method];
+	switch (conv_method) {
+	case TWL4030_MADC_SW1:
+	case TWL4030_MADC_SW2:
+		ret = twl_i2c_write_u8(TWL4030_MODULE_MADC,
+				       TWL4030_MADC_SW_START, method->ctrl);
+		if (ret) {
+			dev_err(madc->dev,
+				"unable to write ctrl register 0x%X\n",
+				method->ctrl);
+			return ret;
+		}
+		break;
+	default:
+		break;
+	}
+
+	return 0;
+}
+
+/*
+ * Function that waits for conversion to be ready
+ * @madc - pointer to twl4030_madc_data struct
+ * @timeout_ms - timeout value in milliseconds
+ * @status_reg - ctrl register
+ * returns 0 if succeeds else a negative error value
+ */
+static int twl4030_madc_wait_conversion_ready(struct twl4030_madc_data *madc,
+					      unsigned int timeout_ms,
+					      u8 status_reg)
+{
+	unsigned long timeout;
+	int ret;
+
+	timeout = jiffies + msecs_to_jiffies(timeout_ms);
+	do {
+		u8 reg;
+
+		ret = twl_i2c_read_u8(TWL4030_MODULE_MADC, &reg, status_reg);
+		if (ret) {
+			dev_err(madc->dev,
+				"unable to read status register 0x%X\n",
+				status_reg);
+			return ret;
+		}
+		if (!(reg & TWL4030_MADC_BUSY) && (reg & TWL4030_MADC_EOC_SW))
+			return 0;
+		usleep_range(500, 2000);
+	} while (!time_after(jiffies, timeout));
+	dev_err(madc->dev, "conversion timeout!\n");
+
+	return -EAGAIN;
+}
+
+/*
+ * An exported function which can be called from other kernel drivers.
+ * @req twl4030_madc_request structure
+ * req->rbuf will be filled with read values of channels based on the
+ * channel index. If a particular channel reading fails there will
+ * be a negative error value in the corresponding array element.
+ * returns 0 if succeeds else error value
+ */
+int twl4030_madc_conversion(struct twl4030_madc_request *req)
+{
+	const struct twl4030_madc_conversion_method *method;
+	u8 ch_msb, ch_lsb;
+	int ret;
+
+	if (!req)
+		return -EINVAL;
+	mutex_lock(&twl4030_madc->lock);
+	if (req->method < TWL4030_MADC_RT || req->method > TWL4030_MADC_SW2) {
+		ret = -EINVAL;
+		goto out;
+	}
+	/* Do we have a conversion request ongoing */
+	if (twl4030_madc->requests[req->method].active) {
+		ret = -EBUSY;
+		goto out;
+	}
+	ch_msb = (req->channels >> 8) & 0xff;
+	ch_lsb = req->channels & 0xff;
+	method = &twl4030_conversion_methods[req->method];
+	/* Select channels to be converted */
+	ret = twl_i2c_write_u8(TWL4030_MODULE_MADC, ch_msb, method->sel + 1);
+	if (ret) {
+		dev_err(twl4030_madc->dev,
+			"unable to write sel register 0x%X\n", method->sel + 1);
+		return ret;
+	}
+	ret = twl_i2c_write_u8(TWL4030_MODULE_MADC, ch_lsb, method->sel);
+	if (ret) {
+		dev_err(twl4030_madc->dev,
+			"unable to write sel register 0x%X\n", method->sel + 1);
+		return ret;
+	}
+	/* Select averaging for all channels if do_avg is set */
+	if (req->do_avg) {
+		ret = twl_i2c_write_u8(TWL4030_MODULE_MADC,
+				       ch_msb, method->avg + 1);
+		if (ret) {
+			dev_err(twl4030_madc->dev,
+				"unable to write avg register 0x%X\n",
+				method->avg + 1);
+			return ret;
+		}
+		ret = twl_i2c_write_u8(TWL4030_MODULE_MADC,
+				       ch_lsb, method->avg);
+		if (ret) {
+			dev_err(twl4030_madc->dev,
+				"unable to write sel reg 0x%X\n",
+				method->sel + 1);
+			return ret;
+		}
+	}
+	if (req->type == TWL4030_MADC_IRQ_ONESHOT && req->func_cb != NULL) {
+		ret = twl4030_madc_set_irq(twl4030_madc, req);
+		if (ret < 0)
+			goto out;
+		ret = twl4030_madc_start_conversion(twl4030_madc, req->method);
+		if (ret < 0)
+			goto out;
+		twl4030_madc->requests[req->method].active = 1;
+		ret = 0;
+		goto out;
+	}
+	/* With RT method we should not be here anymore */
+	if (req->method == TWL4030_MADC_RT) {
+		ret = -EINVAL;
+		goto out;
+	}
+	ret = twl4030_madc_start_conversion(twl4030_madc, req->method);
+	if (ret < 0)
+		goto out;
+	twl4030_madc->requests[req->method].active = 1;
+	/* Wait until conversion is ready (ctrl register returns EOC) */
+	ret = twl4030_madc_wait_conversion_ready(twl4030_madc, 5, method->ctrl);
+	if (ret) {
+		twl4030_madc->requests[req->method].active = 0;
+		goto out;
+	}
+	ret = twl4030_madc_read_channels(twl4030_madc, method->rbase,
+					 req->channels, req->rbuf);
+	twl4030_madc->requests[req->method].active = 0;
+
+out:
+	mutex_unlock(&twl4030_madc->lock);
+
+	return ret;
+}
+EXPORT_SYMBOL_GPL(twl4030_madc_conversion);
+
+/*
+ * Return channel value
+ * Or < 0 on failure.
+ */
+int twl4030_get_madc_conversion(int channel_no)
+{
+	struct twl4030_madc_request req;
+	int temp = 0;
+	int ret;
+
+	req.channels = (1 << channel_no);
+	req.method = TWL4030_MADC_SW2;
+	req.active = 0;
+	req.func_cb = NULL;
+	ret = twl4030_madc_conversion(&req);
+	if (ret < 0)
+		return ret;
+	if (req.rbuf[channel_no] > 0)
+		temp = req.rbuf[channel_no];
+
+	return temp;
+}
+EXPORT_SYMBOL_GPL(twl4030_get_madc_conversion);
+
+/*
+ * Function to enable or disable bias current for
+ * main battery type reading or temperature sensing
+ * @madc - pointer to twl4030_madc_data struct
+ * @chan - can be one of the two values
+ * TWL4030_BCI_ITHEN - Enables bias current for main battery type reading
+ * TWL4030_BCI_TYPEN - Enables bias current for main battery temperature
+ * sensing
+ * @on - enable or disable chan.
+ */
+static int twl4030_madc_set_current_generator(struct twl4030_madc_data *madc,
+					      int chan, int on)
+{
+	int ret;
+	u8 regval;
+
+	ret = twl_i2c_read_u8(TWL4030_MODULE_MAIN_CHARGE,
+			      &regval, TWL4030_BCI_BCICTL1);
+	if (ret) {
+		dev_err(madc->dev, "unable to read BCICTL1 reg 0x%X",
+			TWL4030_BCI_BCICTL1);
+		return ret;
+	}
+	if (on)
+		regval |= chan ? TWL4030_BCI_ITHEN : TWL4030_BCI_TYPEN;
+	else
+		regval &= chan ? ~TWL4030_BCI_ITHEN : ~TWL4030_BCI_TYPEN;
+	ret = twl_i2c_write_u8(TWL4030_MODULE_MAIN_CHARGE,
+			       regval, TWL4030_BCI_BCICTL1);
+	if (ret) {
+		dev_err(madc->dev, "unable to write BCICTL1 reg 0x%X\n",
+			TWL4030_BCI_BCICTL1);
+		return ret;
+	}
+
+	return 0;
+}
+
+/*
+ * Function that sets MADC software power on bit to enable MADC
+ * @madc - pointer to twl4030_madc_data struct
+ * @on - Enable or disable MADC software powen on bit.
+ * returns error if i2c read/write fails else 0
+ */
+static int twl4030_madc_set_power(struct twl4030_madc_data *madc, int on)
+{
+	u8 regval;
+	int ret;
+
+	ret = twl_i2c_read_u8(TWL4030_MODULE_MAIN_CHARGE,
+			      &regval, TWL4030_MADC_CTRL1);
+	if (ret) {
+		dev_err(madc->dev, "unable to read madc ctrl1 reg 0x%X\n",
+			TWL4030_MADC_CTRL1);
+		return ret;
+	}
+	if (on)
+		regval |= TWL4030_MADC_MADCON;
+	else
+		regval &= ~TWL4030_MADC_MADCON;
+	ret = twl_i2c_write_u8(TWL4030_MODULE_MADC, regval, TWL4030_MADC_CTRL1);
+	if (ret) {
+		dev_err(madc->dev, "unable to write madc ctrl1 reg 0x%X\n",
+			TWL4030_MADC_CTRL1);
+		return ret;
+	}
+
+	return 0;
+}
+
+/*
+ * Initialize MADC and request for threaded irq
+ */
+static int __devinit twl4030_madc_probe(struct platform_device *pdev)
+{
+	struct twl4030_madc_data *madc;
+	struct twl4030_madc_platform_data *pdata = pdev->dev.platform_data;
+	int ret;
+	u8 regval;
+
+	if (!pdata) {
+		dev_err(&pdev->dev, "platform_data not available\n");
+		return -EINVAL;
+	}
+	madc = kzalloc(sizeof(*madc), GFP_KERNEL);
+	if (!madc)
+		return -ENOMEM;
+
+	/*
+	 * Phoenix provides 2 interrupt lines. The first one is connected to
+	 * the OMAP. The other one can be connected to the other processor such
+	 * as modem. Hence two separate ISR and IMR registers.
+	 */
+	madc->imr = (pdata->irq_line == 1) ?
+	    TWL4030_MADC_IMR1 : TWL4030_MADC_IMR2;
+	madc->isr = (pdata->irq_line == 1) ?
+	    TWL4030_MADC_ISR1 : TWL4030_MADC_ISR2;
+	ret = twl4030_madc_set_power(madc, 1);
+	if (ret < 0)
+		goto err_power;
+	ret = twl4030_madc_set_current_generator(madc, 0, 1);
+	if (ret < 0)
+		goto err_current_generator;
+
+	ret = twl_i2c_read_u8(TWL4030_MODULE_MAIN_CHARGE,
+			      &regval, TWL4030_BCI_BCICTL1);
+	if (ret) {
+		dev_err(&pdev->dev, "unable to read reg BCI CTL1 0x%X\n",
+			TWL4030_BCI_BCICTL1);
+		goto err_i2c;
+	}
+	regval |= TWL4030_BCI_MESBAT;
+	ret = twl_i2c_write_u8(TWL4030_MODULE_MAIN_CHARGE,
+			       regval, TWL4030_BCI_BCICTL1);
+	if (ret) {
+		dev_err(&pdev->dev, "unable to write reg BCI Ctl1 0x%X\n",
+			TWL4030_BCI_BCICTL1);
+		goto err_i2c;
+	}
+	platform_set_drvdata(pdev, madc);
+	mutex_init(&madc->lock);
+	ret = request_threaded_irq(platform_get_irq(pdev, 0), NULL,
+				   twl4030_madc_threaded_irq_handler,
+				   IRQF_TRIGGER_RISING, "twl4030_madc", madc);
+	if (ret) {
+		dev_dbg(&pdev->dev, "could not request irq\n");
+		goto err_irq;
+	}
+	twl4030_madc = madc;
+	return 0;
+err_irq:
+	platform_set_drvdata(pdev, NULL);
+err_i2c:
+	twl4030_madc_set_current_generator(madc, 0, 0);
+err_current_generator:
+	twl4030_madc_set_power(madc, 0);
+err_power:
+	kfree(madc);
+
+	return ret;
+}
+
+static int __devexit twl4030_madc_remove(struct platform_device *pdev)
+{
+	struct twl4030_madc_data *madc = platform_get_drvdata(pdev);
+
+	free_irq(platform_get_irq(pdev, 0), madc);
+	platform_set_drvdata(pdev, NULL);
+	twl4030_madc_set_current_generator(madc, 0, 0);
+	twl4030_madc_set_power(madc, 0);
+	kfree(madc);
+
+	return 0;
+}
+
+static struct platform_driver twl4030_madc_driver = {
+	.probe = twl4030_madc_probe,
+	.remove = __exit_p(twl4030_madc_remove),
+	.driver = {
+		   .name = "twl4030_madc",
+		   .owner = THIS_MODULE,
+		   },
+};
+
+static int __init twl4030_madc_init(void)
+{
+	return platform_driver_register(&twl4030_madc_driver);
+}
+
+module_init(twl4030_madc_init);
+
+static void __exit twl4030_madc_exit(void)
+{
+	platform_driver_unregister(&twl4030_madc_driver);
+}
+
+module_exit(twl4030_madc_exit);
+
+MODULE_DESCRIPTION("TWL4030 ADC driver");
+MODULE_LICENSE("GPL");
+MODULE_AUTHOR("J Keerthy");
+MODULE_ALIAS("platform:twl4030_madc");
diff --git a/drivers/mfd/ucb1x00-ts.c b/drivers/mfd/ucb1x00-ts.c
index 92b85e2..38ffbd5 100644
--- a/drivers/mfd/ucb1x00-ts.c
+++ b/drivers/mfd/ucb1x00-ts.c
@@ -60,6 +60,7 @@
 	input_report_abs(idev, ABS_X, x);
 	input_report_abs(idev, ABS_Y, y);
 	input_report_abs(idev, ABS_PRESSURE, pressure);
+	input_report_key(idev, BTN_TOUCH, 1);
 	input_sync(idev);
 }
 
@@ -68,6 +69,7 @@
 	struct input_dev *idev = ts->idev;
 
 	input_report_abs(idev, ABS_PRESSURE, 0);
+	input_report_key(idev, BTN_TOUCH, 0);
 	input_sync(idev);
 }
 
@@ -384,7 +386,8 @@
 	idev->open       = ucb1x00_ts_open;
 	idev->close      = ucb1x00_ts_close;
 
-	__set_bit(EV_ABS, idev->evbit);
+	idev->evbit[0]   = BIT_MASK(EV_ABS) | BIT_MASK(EV_KEY);
+	idev->keybit[BIT_WORD(BTN_TOUCH)] = BIT_MASK(BTN_TOUCH);
 
 	input_set_drvdata(idev, ts);
 
diff --git a/drivers/mfd/vx855.c b/drivers/mfd/vx855.c
index 348052a..d698703 100644
--- a/drivers/mfd/vx855.c
+++ b/drivers/mfd/vx855.c
@@ -122,6 +122,7 @@
 	{ PCI_DEVICE(PCI_VENDOR_ID_VIA, PCI_DEVICE_ID_VIA_VX855) },
 	{ 0, }
 };
+MODULE_DEVICE_TABLE(pci, vx855_pci_tbl);
 
 static struct pci_driver vx855_pci_driver = {
 	.name		= "vx855",
diff --git a/drivers/mfd/wl1273-core.c b/drivers/mfd/wl1273-core.c
index d2ecc24..529d65b 100644
--- a/drivers/mfd/wl1273-core.c
+++ b/drivers/mfd/wl1273-core.c
@@ -38,7 +38,6 @@
 	dev_dbg(&client->dev, "%s\n", __func__);
 
 	mfd_remove_devices(&client->dev);
-	i2c_set_clientdata(client, NULL);
 	kfree(core);
 
 	return 0;
@@ -79,8 +78,7 @@
 
 	cell = &core->cells[children];
 	cell->name = "wl1273_fm_radio";
-	cell->platform_data = &core;
-	cell->data_size = sizeof(core);
+	cell->mfd_data = &core;
 	children++;
 
 	if (pdata->children & WL1273_CODEC_CHILD) {
@@ -88,8 +86,7 @@
 
 		dev_dbg(&client->dev, "%s: Have codec.\n", __func__);
 		cell->name = "wl1273-codec";
-		cell->platform_data = &core;
-		cell->data_size = sizeof(core);
+		cell->mfd_data = &core;
 		children++;
 	}
 
@@ -104,7 +101,6 @@
 	return 0;
 
 err:
-	i2c_set_clientdata(client, NULL);
 	pdata->free_resources();
 	kfree(core);
 
diff --git a/drivers/mfd/wm831x-i2c.c b/drivers/mfd/wm831x-i2c.c
index 3853fa8..a06cbc7 100644
--- a/drivers/mfd/wm831x-i2c.c
+++ b/drivers/mfd/wm831x-i2c.c
@@ -51,17 +51,25 @@
 				   int bytes, void *src)
 {
 	struct i2c_client *i2c = wm831x->control_data;
-	unsigned char msg[bytes + 2];
+	struct i2c_msg xfer[2];
 	int ret;
 
 	reg = cpu_to_be16(reg);
-	memcpy(&msg[0], &reg, 2);
-	memcpy(&msg[2], src, bytes);
 
-	ret = i2c_master_send(i2c, msg, bytes + 2);
+	xfer[0].addr = i2c->addr;
+	xfer[0].flags = 0;
+	xfer[0].len = 2;
+	xfer[0].buf = (char *)&reg;
+
+	xfer[1].addr = i2c->addr;
+	xfer[1].flags = I2C_M_NOSTART;
+	xfer[1].len = bytes;
+	xfer[1].buf = (char *)src;
+
+	ret = i2c_transfer(i2c->adapter, xfer, 2);
 	if (ret < 0)
 		return ret;
-	if (ret < bytes + 2)
+	if (ret != 2)
 		return -EIO;
 
 	return 0;
diff --git a/drivers/mfd/wm831x-irq.c b/drivers/mfd/wm831x-irq.c
index f7192d4..a5cd17e 100644
--- a/drivers/mfd/wm831x-irq.c
+++ b/drivers/mfd/wm831x-irq.c
@@ -26,15 +26,6 @@
 
 #include <linux/delay.h>
 
-/*
- * Since generic IRQs don't currently support interrupt controllers on
- * interrupt driven buses we don't use genirq but instead provide an
- * interface that looks very much like the standard ones.  This leads
- * to some bodges, including storing interrupt handler information in
- * the static irq_data table we use to look up the data for individual
- * interrupts, but hopefully won't last too long.
- */
-
 struct wm831x_irq_data {
 	int primary;
 	int reg;
@@ -361,6 +352,10 @@
 		/* If there's been a change in the mask write it back
 		 * to the hardware. */
 		if (wm831x->irq_masks_cur[i] != wm831x->irq_masks_cache[i]) {
+			dev_dbg(wm831x->dev, "IRQ mask sync: %x = %x\n",
+				WM831X_INTERRUPT_STATUS_1_MASK + i,
+				wm831x->irq_masks_cur[i]);
+
 			wm831x->irq_masks_cache[i] = wm831x->irq_masks_cur[i];
 			wm831x_reg_write(wm831x,
 					 WM831X_INTERRUPT_STATUS_1_MASK + i,
@@ -371,7 +366,7 @@
 	mutex_unlock(&wm831x->irq_lock);
 }
 
-static void wm831x_irq_unmask(struct irq_data *data)
+static void wm831x_irq_enable(struct irq_data *data)
 {
 	struct wm831x *wm831x = irq_data_get_irq_chip_data(data);
 	struct wm831x_irq_data *irq_data = irq_to_wm831x_irq(wm831x,
@@ -380,7 +375,7 @@
 	wm831x->irq_masks_cur[irq_data->reg - 1] &= ~irq_data->mask;
 }
 
-static void wm831x_irq_mask(struct irq_data *data)
+static void wm831x_irq_disable(struct irq_data *data)
 {
 	struct wm831x *wm831x = irq_data_get_irq_chip_data(data);
 	struct wm831x_irq_data *irq_data = irq_to_wm831x_irq(wm831x,
@@ -426,8 +421,8 @@
 	.name			= "wm831x",
 	.irq_bus_lock		= wm831x_irq_lock,
 	.irq_bus_sync_unlock	= wm831x_irq_sync_unlock,
-	.irq_mask		= wm831x_irq_mask,
-	.irq_unmask		= wm831x_irq_unmask,
+	.irq_disable		= wm831x_irq_disable,
+	.irq_enable		= wm831x_irq_enable,
 	.irq_set_type		= wm831x_irq_set_type,
 };
 
@@ -449,6 +444,18 @@
 		goto out;
 	}
 
+	/* The touch interrupts are visible in the primary register as
+	 * an optimisation; open code this to avoid complicating the
+	 * main handling loop and so we can also skip iterating the
+	 * descriptors.
+	 */
+	if (primary & WM831X_TCHPD_INT)
+		handle_nested_irq(wm831x->irq_base + WM831X_IRQ_TCHPD);
+	if (primary & WM831X_TCHDATA_INT)
+		handle_nested_irq(wm831x->irq_base + WM831X_IRQ_TCHDATA);
+	if (primary & (WM831X_TCHDATA_EINT | WM831X_TCHPD_EINT))
+		goto out;
+
 	for (i = 0; i < ARRAY_SIZE(wm831x_irqs); i++) {
 		int offset = wm831x_irqs[i].reg - 1;
 
@@ -481,6 +488,9 @@
 	}
 
 out:
+	/* Touchscreen interrupts are handled specially in the driver */
+	status_regs[0] &= ~(WM831X_TCHDATA_EINT | WM831X_TCHPD_EINT);
+
 	for (i = 0; i < ARRAY_SIZE(status_regs); i++) {
 		if (status_regs[i])
 			wm831x_reg_write(wm831x, WM831X_INTERRUPT_STATUS_1 + i,
@@ -517,6 +527,14 @@
 		return 0;
 	}
 
+	if (pdata->irq_cmos)
+		i = 0;
+	else
+		i = WM831X_IRQ_OD;
+
+	wm831x_set_bits(wm831x, WM831X_IRQ_CONFIG,
+			WM831X_IRQ_OD, i);
+
 	/* Try to flag /IRQ as a wake source; there are a number of
 	 * unconditional wake sources in the PMIC so this isn't
 	 * conditional but we don't actually care *too* much if it
diff --git a/drivers/mfd/wm831x-spi.c b/drivers/mfd/wm831x-spi.c
index 0a8f772..eed8e4f 100644
--- a/drivers/mfd/wm831x-spi.c
+++ b/drivers/mfd/wm831x-spi.c
@@ -14,6 +14,7 @@
 
 #include <linux/kernel.h>
 #include <linux/module.h>
+#include <linux/pm.h>
 #include <linux/spi/spi.h>
 
 #include <linux/mfd/wm831x/core.h>
@@ -113,22 +114,27 @@
 	return 0;
 }
 
-static int wm831x_spi_suspend(struct spi_device *spi, pm_message_t m)
+static int wm831x_spi_suspend(struct device *dev)
 {
-	struct wm831x *wm831x = dev_get_drvdata(&spi->dev);
+	struct wm831x *wm831x = dev_get_drvdata(dev);
 
 	return wm831x_device_suspend(wm831x);
 }
 
+static const struct dev_pm_ops wm831x_spi_pm = {
+	.freeze = wm831x_spi_suspend,
+	.suspend = wm831x_spi_suspend,
+};
+
 static struct spi_driver wm8310_spi_driver = {
 	.driver = {
 		.name	= "wm8310",
 		.bus	= &spi_bus_type,
 		.owner	= THIS_MODULE,
+		.pm	= &wm831x_spi_pm,
 	},
 	.probe		= wm831x_spi_probe,
 	.remove		= __devexit_p(wm831x_spi_remove),
-	.suspend	= wm831x_spi_suspend,
 };
 
 static struct spi_driver wm8311_spi_driver = {
@@ -136,10 +142,10 @@
 		.name	= "wm8311",
 		.bus	= &spi_bus_type,
 		.owner	= THIS_MODULE,
+		.pm	= &wm831x_spi_pm,
 	},
 	.probe		= wm831x_spi_probe,
 	.remove		= __devexit_p(wm831x_spi_remove),
-	.suspend	= wm831x_spi_suspend,
 };
 
 static struct spi_driver wm8312_spi_driver = {
@@ -147,10 +153,10 @@
 		.name	= "wm8312",
 		.bus	= &spi_bus_type,
 		.owner	= THIS_MODULE,
+		.pm	= &wm831x_spi_pm,
 	},
 	.probe		= wm831x_spi_probe,
 	.remove		= __devexit_p(wm831x_spi_remove),
-	.suspend	= wm831x_spi_suspend,
 };
 
 static struct spi_driver wm8320_spi_driver = {
@@ -158,10 +164,10 @@
 		.name	= "wm8320",
 		.bus	= &spi_bus_type,
 		.owner	= THIS_MODULE,
+		.pm	= &wm831x_spi_pm,
 	},
 	.probe		= wm831x_spi_probe,
 	.remove		= __devexit_p(wm831x_spi_remove),
-	.suspend	= wm831x_spi_suspend,
 };
 
 static struct spi_driver wm8321_spi_driver = {
@@ -169,10 +175,10 @@
 		.name	= "wm8321",
 		.bus	= &spi_bus_type,
 		.owner	= THIS_MODULE,
+		.pm	= &wm831x_spi_pm,
 	},
 	.probe		= wm831x_spi_probe,
 	.remove		= __devexit_p(wm831x_spi_remove),
-	.suspend	= wm831x_spi_suspend,
 };
 
 static struct spi_driver wm8325_spi_driver = {
@@ -180,10 +186,10 @@
 		.name	= "wm8325",
 		.bus	= &spi_bus_type,
 		.owner	= THIS_MODULE,
+		.pm	= &wm831x_spi_pm,
 	},
 	.probe		= wm831x_spi_probe,
 	.remove		= __devexit_p(wm831x_spi_remove),
-	.suspend	= wm831x_spi_suspend,
 };
 
 static struct spi_driver wm8326_spi_driver = {
@@ -191,10 +197,10 @@
 		.name	= "wm8326",
 		.bus	= &spi_bus_type,
 		.owner	= THIS_MODULE,
+		.pm	= &wm831x_spi_pm,
 	},
 	.probe		= wm831x_spi_probe,
 	.remove		= __devexit_p(wm831x_spi_remove),
-	.suspend	= wm831x_spi_suspend,
 };
 
 static int __init wm831x_spi_init(void)
diff --git a/drivers/mfd/wm8400-core.c b/drivers/mfd/wm8400-core.c
index 1bfef48..3a6e78c 100644
--- a/drivers/mfd/wm8400-core.c
+++ b/drivers/mfd/wm8400-core.c
@@ -245,7 +245,7 @@
 {
 	struct mfd_cell cell = {
 		.name = "wm8400-codec",
-		.driver_data = wm8400,
+		.mfd_data = wm8400,
 	};
 
 	return mfd_add_devices(wm8400->dev, -1, &cell, 1, NULL, 0);
diff --git a/drivers/mfd/wm8994-core.c b/drivers/mfd/wm8994-core.c
index f4016a0..e198d40 100644
--- a/drivers/mfd/wm8994-core.c
+++ b/drivers/mfd/wm8994-core.c
@@ -40,10 +40,8 @@
 		return ret;
 
 	for (i = 0; i < bytes / 2; i++) {
-		buf[i] = be16_to_cpu(buf[i]);
-
 		dev_vdbg(wm8994->dev, "Read %04x from R%d(0x%x)\n",
-			 buf[i], reg + i, reg + i);
+			 be16_to_cpu(buf[i]), reg + i, reg + i);
 	}
 
 	return 0;
@@ -69,7 +67,7 @@
 	if (ret < 0)
 		return ret;
 	else
-		return val;
+		return be16_to_cpu(val);
 }
 EXPORT_SYMBOL_GPL(wm8994_reg_read);
 
@@ -79,7 +77,7 @@
  * @wm8994: Device to read from
  * @reg: First register
  * @count: Number of registers
- * @buf: Buffer to fill.
+ * @buf: Buffer to fill.  The data will be returned big endian.
  */
 int wm8994_bulk_read(struct wm8994 *wm8994, unsigned short reg,
 		     int count, u16 *buf)
@@ -97,9 +95,9 @@
 EXPORT_SYMBOL_GPL(wm8994_bulk_read);
 
 static int wm8994_write(struct wm8994 *wm8994, unsigned short reg,
-			int bytes, void *src)
+			int bytes, const void *src)
 {
-	u16 *buf = src;
+	const u16 *buf = src;
 	int i;
 
 	BUG_ON(bytes % 2);
@@ -107,9 +105,7 @@
 
 	for (i = 0; i < bytes / 2; i++) {
 		dev_vdbg(wm8994->dev, "Write %04x to R%d(0x%x)\n",
-			 buf[i], reg + i, reg + i);
-
-		buf[i] = cpu_to_be16(buf[i]);
+			 be16_to_cpu(buf[i]), reg + i, reg + i);
 	}
 
 	return wm8994->write_dev(wm8994, reg, bytes, src);
@@ -127,6 +123,8 @@
 {
 	int ret;
 
+	val = cpu_to_be16(val);
+
 	mutex_lock(&wm8994->io_lock);
 
 	ret = wm8994_write(wm8994, reg, 2, &val);
@@ -138,6 +136,29 @@
 EXPORT_SYMBOL_GPL(wm8994_reg_write);
 
 /**
+ * wm8994_bulk_write: Write multiple WM8994 registers
+ *
+ * @wm8994: Device to write to
+ * @reg: First register
+ * @count: Number of registers
+ * @buf: Buffer to write from.  Data must be big-endian formatted.
+ */
+int wm8994_bulk_write(struct wm8994 *wm8994, unsigned short reg,
+		      int count, const u16 *buf)
+{
+	int ret;
+
+	mutex_lock(&wm8994->io_lock);
+
+	ret = wm8994_write(wm8994, reg, count * 2, buf);
+
+	mutex_unlock(&wm8994->io_lock);
+
+	return ret;
+}
+EXPORT_SYMBOL_GPL(wm8994_bulk_write);
+
+/**
  * wm8994_set_bits: Set the value of a bitfield in a WM8994 register
  *
  * @wm8994: Device to write to.
@@ -157,9 +178,13 @@
 	if (ret < 0)
 		goto out;
 
+	r = be16_to_cpu(r);
+
 	r &= ~mask;
 	r |= val;
 
+	r = cpu_to_be16(r);
+
 	ret = wm8994_write(wm8994, reg, 2, &r);
 
 out:
@@ -271,6 +296,11 @@
 	if (ret < 0)
 		dev_err(dev, "Failed to save LDO registers: %d\n", ret);
 
+	/* Explicitly put the device into reset in case regulators
+	 * don't get disabled in order to ensure consistent restart.
+	 */
+	wm8994_reg_write(wm8994, WM8994_SOFTWARE_RESET, 0x8994);
+
 	wm8994->suspended = true;
 
 	ret = regulator_bulk_disable(wm8994->num_supplies,
@@ -552,25 +582,29 @@
 	return 0;
 }
 
-/* Currently we allocate the write buffer on the stack; this is OK for
- * small writes - if we need to do large writes this will need to be
- * revised.
- */
 static int wm8994_i2c_write_device(struct wm8994 *wm8994, unsigned short reg,
-				   int bytes, void *src)
+				   int bytes, const void *src)
 {
 	struct i2c_client *i2c = wm8994->control_data;
-	unsigned char msg[bytes + 2];
+	struct i2c_msg xfer[2];
 	int ret;
 
 	reg = cpu_to_be16(reg);
-	memcpy(&msg[0], &reg, 2);
-	memcpy(&msg[2], src, bytes);
 
-	ret = i2c_master_send(i2c, msg, bytes + 2);
+	xfer[0].addr = i2c->addr;
+	xfer[0].flags = 0;
+	xfer[0].len = 2;
+	xfer[0].buf = (char *)&reg;
+
+	xfer[1].addr = i2c->addr;
+	xfer[1].flags = I2C_M_NOSTART;
+	xfer[1].len = bytes;
+	xfer[1].buf = (char *)src;
+
+	ret = i2c_transfer(i2c->adapter, xfer, 2);
 	if (ret < 0)
 		return ret;
-	if (ret < bytes + 2)
+	if (ret != 2)
 		return -EIO;
 
 	return 0;
@@ -612,7 +646,8 @@
 };
 MODULE_DEVICE_TABLE(i2c, wm8994_i2c_id);
 
-UNIVERSAL_DEV_PM_OPS(wm8994_pm_ops, wm8994_suspend, wm8994_resume, NULL);
+static UNIVERSAL_DEV_PM_OPS(wm8994_pm_ops, wm8994_suspend, wm8994_resume,
+			    NULL);
 
 static struct i2c_driver wm8994_i2c_driver = {
 	.driver = {
diff --git a/drivers/mfd/wm8994-irq.c b/drivers/mfd/wm8994-irq.c
index 29e8faf..1e3bf4a 100644
--- a/drivers/mfd/wm8994-irq.c
+++ b/drivers/mfd/wm8994-irq.c
@@ -182,7 +182,7 @@
 	mutex_unlock(&wm8994->irq_lock);
 }
 
-static void wm8994_irq_unmask(struct irq_data *data)
+static void wm8994_irq_enable(struct irq_data *data)
 {
 	struct wm8994 *wm8994 = irq_data_get_irq_chip_data(data);
 	struct wm8994_irq_data *irq_data = irq_to_wm8994_irq(wm8994,
@@ -191,7 +191,7 @@
 	wm8994->irq_masks_cur[irq_data->reg - 1] &= ~irq_data->mask;
 }
 
-static void wm8994_irq_mask(struct irq_data *data)
+static void wm8994_irq_disable(struct irq_data *data)
 {
 	struct wm8994 *wm8994 = irq_data_get_irq_chip_data(data);
 	struct wm8994_irq_data *irq_data = irq_to_wm8994_irq(wm8994,
@@ -204,8 +204,8 @@
 	.name			= "wm8994",
 	.irq_bus_lock		= wm8994_irq_lock,
 	.irq_bus_sync_unlock	= wm8994_irq_sync_unlock,
-	.irq_mask		= wm8994_irq_mask,
-	.irq_unmask		= wm8994_irq_unmask,
+	.irq_disable		= wm8994_irq_disable,
+	.irq_enable		= wm8994_irq_enable,
 };
 
 /* The processing of the primary interrupt occurs in a thread so that
@@ -225,9 +225,11 @@
 		return IRQ_NONE;
 	}
 
-	/* Apply masking */
-	for (i = 0; i < WM8994_NUM_IRQ_REGS; i++)
+	/* Bit swap and apply masking */
+	for (i = 0; i < WM8994_NUM_IRQ_REGS; i++) {
+		status[i] = be16_to_cpu(status[i]);
 		status[i] &= ~wm8994->irq_masks_cur[i];
+	}
 
 	/* Report */
 	for (i = 0; i < ARRAY_SIZE(wm8994_irqs); i++) {
diff --git a/drivers/mmc/host/tmio_mmc.c b/drivers/mmc/host/tmio_mmc.c
index ac52eb6..ab1adea 100644
--- a/drivers/mmc/host/tmio_mmc.c
+++ b/drivers/mmc/host/tmio_mmc.c
@@ -303,8 +303,7 @@
 
 static void tmio_mmc_clk_stop(struct tmio_mmc_host *host)
 {
-	struct mfd_cell *cell = host->pdev->dev.platform_data;
-	struct tmio_mmc_data *pdata = cell->driver_data;
+	struct tmio_mmc_data *pdata = mfd_get_data(host->pdev);
 
 	/*
 	 * Testing on sh-mobile showed that SDIO IRQs are unmasked when
@@ -327,8 +326,7 @@
 
 static void tmio_mmc_clk_start(struct tmio_mmc_host *host)
 {
-	struct mfd_cell *cell = host->pdev->dev.platform_data;
-	struct tmio_mmc_data *pdata = cell->driver_data;
+	struct tmio_mmc_data *pdata = mfd_get_data(host->pdev);
 
 	sd_ctrl_write16(host, CTL_SD_CARD_CLK_CTL, 0x0100 |
 		sd_ctrl_read16(host, CTL_SD_CARD_CLK_CTL));
@@ -669,8 +667,7 @@
 static irqreturn_t tmio_mmc_irq(int irq, void *devid)
 {
 	struct tmio_mmc_host *host = devid;
-	struct mfd_cell	*cell = host->pdev->dev.platform_data;
-	struct tmio_mmc_data *pdata = cell->driver_data;
+	struct tmio_mmc_data *pdata = mfd_get_data(host->pdev);
 	unsigned int ireg, irq_mask, status;
 	unsigned int sdio_ireg, sdio_irq_mask, sdio_status;
 
@@ -799,8 +796,7 @@
 	struct scatterlist *sg = host->sg_ptr, *sg_tmp;
 	struct dma_async_tx_descriptor *desc = NULL;
 	struct dma_chan *chan = host->chan_rx;
-	struct mfd_cell	*cell = host->pdev->dev.platform_data;
-	struct tmio_mmc_data *pdata = cell->driver_data;
+	struct tmio_mmc_data *pdata = mfd_get_data(host->pdev);
 	dma_cookie_t cookie;
 	int ret, i;
 	bool aligned = true, multiple = true;
@@ -869,8 +865,7 @@
 	struct scatterlist *sg = host->sg_ptr, *sg_tmp;
 	struct dma_async_tx_descriptor *desc = NULL;
 	struct dma_chan *chan = host->chan_tx;
-	struct mfd_cell	*cell = host->pdev->dev.platform_data;
-	struct tmio_mmc_data *pdata = cell->driver_data;
+	struct tmio_mmc_data *pdata = mfd_get_data(host->pdev);
 	dma_cookie_t cookie;
 	int ret, i;
 	bool aligned = true, multiple = true;
@@ -1063,8 +1058,7 @@
 static int tmio_mmc_start_data(struct tmio_mmc_host *host,
 	struct mmc_data *data)
 {
-	struct mfd_cell *cell = host->pdev->dev.platform_data;
-	struct tmio_mmc_data *pdata = cell->driver_data;
+	struct tmio_mmc_data *pdata = mfd_get_data(host->pdev);
 
 	pr_debug("setup data transfer: blocksize %08x  nr_blocks %d\n",
 		 data->blksz, data->blocks);
@@ -1169,8 +1163,7 @@
 static int tmio_mmc_get_ro(struct mmc_host *mmc)
 {
 	struct tmio_mmc_host *host = mmc_priv(mmc);
-	struct mfd_cell	*cell = host->pdev->dev.platform_data;
-	struct tmio_mmc_data *pdata = cell->driver_data;
+	struct tmio_mmc_data *pdata = mfd_get_data(host->pdev);
 
 	return ((pdata->flags & TMIO_MMC_WRPROTECT_DISABLE) ||
 		(sd_ctrl_read32(host, CTL_STATUS) & TMIO_STAT_WRPROTECT)) ? 0 : 1;
@@ -1179,8 +1172,7 @@
 static int tmio_mmc_get_cd(struct mmc_host *mmc)
 {
 	struct tmio_mmc_host *host = mmc_priv(mmc);
-	struct mfd_cell	*cell = host->pdev->dev.platform_data;
-	struct tmio_mmc_data *pdata = cell->driver_data;
+	struct tmio_mmc_data *pdata = mfd_get_data(host->pdev);
 
 	if (!pdata->get_cd)
 		return -ENOSYS;
@@ -1199,7 +1191,7 @@
 #ifdef CONFIG_PM
 static int tmio_mmc_suspend(struct platform_device *dev, pm_message_t state)
 {
-	struct mfd_cell	*cell = (struct mfd_cell *)dev->dev.platform_data;
+	const struct mfd_cell *cell = mfd_get_cell(dev);
 	struct mmc_host *mmc = platform_get_drvdata(dev);
 	int ret;
 
@@ -1214,7 +1206,7 @@
 
 static int tmio_mmc_resume(struct platform_device *dev)
 {
-	struct mfd_cell	*cell = (struct mfd_cell *)dev->dev.platform_data;
+	const struct mfd_cell *cell = mfd_get_cell(dev);
 	struct mmc_host *mmc = platform_get_drvdata(dev);
 	int ret = 0;
 
@@ -1237,7 +1229,7 @@
 
 static int __devinit tmio_mmc_probe(struct platform_device *dev)
 {
-	struct mfd_cell	*cell = (struct mfd_cell *)dev->dev.platform_data;
+	const struct mfd_cell *cell = mfd_get_cell(dev);
 	struct tmio_mmc_data *pdata;
 	struct resource *res_ctl;
 	struct tmio_mmc_host *host;
@@ -1252,7 +1244,7 @@
 	if (!res_ctl)
 		goto out;
 
-	pdata = cell->driver_data;
+	pdata = mfd_get_data(dev);
 	if (!pdata || !pdata->hclk)
 		goto out;
 
@@ -1352,7 +1344,7 @@
 
 static int __devexit tmio_mmc_remove(struct platform_device *dev)
 {
-	struct mfd_cell	*cell = (struct mfd_cell *)dev->dev.platform_data;
+	const struct mfd_cell *cell = mfd_get_cell(dev);
 	struct mmc_host *mmc = platform_get_drvdata(dev);
 
 	platform_set_drvdata(dev, NULL);
diff --git a/drivers/mtd/nand/tmio_nand.c b/drivers/mtd/nand/tmio_nand.c
index 3041d1f..38fb167 100644
--- a/drivers/mtd/nand/tmio_nand.c
+++ b/drivers/mtd/nand/tmio_nand.c
@@ -319,7 +319,7 @@
 
 static int tmio_hw_init(struct platform_device *dev, struct tmio_nand *tmio)
 {
-	struct mfd_cell *cell = dev_get_platdata(&dev->dev);
+	const struct mfd_cell *cell = mfd_get_cell(dev);
 	int ret;
 
 	if (cell->enable) {
@@ -363,7 +363,7 @@
 
 static void tmio_hw_stop(struct platform_device *dev, struct tmio_nand *tmio)
 {
-	struct mfd_cell *cell = dev_get_platdata(&dev->dev);
+	const struct mfd_cell *cell = mfd_get_cell(dev);
 
 	tmio_iowrite8(FCR_MODE_POWER_OFF, tmio->fcr + FCR_MODE);
 	if (cell->disable)
@@ -372,8 +372,7 @@
 
 static int tmio_probe(struct platform_device *dev)
 {
-	struct mfd_cell *cell = dev_get_platdata(&dev->dev);
-	struct tmio_nand_data *data = cell->driver_data;
+	struct tmio_nand_data *data = mfd_get_data(dev);
 	struct resource *fcr = platform_get_resource(dev,
 			IORESOURCE_MEM, 0);
 	struct resource *ccr = platform_get_resource(dev,
@@ -516,7 +515,7 @@
 #ifdef CONFIG_PM
 static int tmio_suspend(struct platform_device *dev, pm_message_t state)
 {
-	struct mfd_cell *cell = dev_get_platdata(&dev->dev);
+	const struct mfd_cell *cell = mfd_get_cell(dev);
 
 	if (cell->suspend)
 		cell->suspend(dev);
@@ -527,7 +526,7 @@
 
 static int tmio_resume(struct platform_device *dev)
 {
-	struct mfd_cell *cell = dev_get_platdata(&dev->dev);
+	const struct mfd_cell *cell = mfd_get_cell(dev);
 
 	/* FIXME - is this required or merely another attack of the broken
 	 * SHARP platform? Looks suspicious.
diff --git a/drivers/net/can/janz-ican3.c b/drivers/net/can/janz-ican3.c
index 366f5cc..102b16c 100644
--- a/drivers/net/can/janz-ican3.c
+++ b/drivers/net/can/janz-ican3.c
@@ -15,6 +15,7 @@
 #include <linux/interrupt.h>
 #include <linux/delay.h>
 #include <linux/platform_device.h>
+#include <linux/mfd/core.h>
 
 #include <linux/netdevice.h>
 #include <linux/can.h>
@@ -1643,7 +1644,7 @@
 	struct device *dev;
 	int ret;
 
-	pdata = pdev->dev.platform_data;
+	pdata = mfd_get_data(pdev);
 	if (!pdata)
 		return -ENXIO;
 
diff --git a/drivers/net/ks8842.c b/drivers/net/ks8842.c
index 928b2b8..efd44af 100644
--- a/drivers/net/ks8842.c
+++ b/drivers/net/ks8842.c
@@ -26,6 +26,7 @@
 #include <linux/kernel.h>
 #include <linux/module.h>
 #include <linux/platform_device.h>
+#include <linux/mfd/core.h>
 #include <linux/netdevice.h>
 #include <linux/etherdevice.h>
 #include <linux/ethtool.h>
@@ -1145,7 +1146,7 @@
 	struct resource *iomem;
 	struct net_device *netdev;
 	struct ks8842_adapter *adapter;
-	struct ks8842_platform_data *pdata = pdev->dev.platform_data;
+	struct ks8842_platform_data *pdata = mfd_get_data(pdev);
 	u16 id;
 	unsigned i;
 
diff --git a/drivers/power/jz4740-battery.c b/drivers/power/jz4740-battery.c
index 02414db..763f894 100644
--- a/drivers/power/jz4740-battery.c
+++ b/drivers/power/jz4740-battery.c
@@ -39,7 +39,7 @@
 	int irq;
 	int charge_irq;
 
-	struct mfd_cell *cell;
+	const struct mfd_cell *cell;
 
 	int status;
 	long voltage;
@@ -258,7 +258,7 @@
 		return -ENOMEM;
 	}
 
-	jz_battery->cell = pdev->dev.platform_data;
+	jz_battery->cell = mfd_get_cell(pdev);
 
 	jz_battery->irq = platform_get_irq(pdev, 0);
 	if (jz_battery->irq < 0) {
diff --git a/drivers/regulator/88pm8607.c b/drivers/regulator/88pm8607.c
index dd63084..8592512 100644
--- a/drivers/regulator/88pm8607.c
+++ b/drivers/regulator/88pm8607.c
@@ -15,6 +15,7 @@
 #include <linux/platform_device.h>
 #include <linux/regulator/driver.h>
 #include <linux/regulator/machine.h>
+#include <linux/mfd/core.h>
 #include <linux/mfd/88pm860x.h>
 
 struct pm8607_regulator_info {
@@ -394,47 +395,48 @@
 	PM8607_LDO(14,        LDO14, 0, 4, SUPPLIES_EN12, 6),
 };
 
-static inline struct pm8607_regulator_info *find_regulator_info(int id)
-{
-	struct pm8607_regulator_info *info;
-	int i;
-
-	for (i = 0; i < ARRAY_SIZE(pm8607_regulator_info); i++) {
-		info = &pm8607_regulator_info[i];
-		if (info->desc.id == id)
-			return info;
-	}
-	return NULL;
-}
-
 static int __devinit pm8607_regulator_probe(struct platform_device *pdev)
 {
 	struct pm860x_chip *chip = dev_get_drvdata(pdev->dev.parent);
-	struct pm860x_platform_data *pdata = chip->dev->platform_data;
 	struct pm8607_regulator_info *info = NULL;
+	struct regulator_init_data *pdata;
+	struct mfd_cell *cell;
+	int i;
 
-	info = find_regulator_info(pdev->id);
-	if (info == NULL) {
-		dev_err(&pdev->dev, "invalid regulator ID specified\n");
+	cell = pdev->dev.platform_data;
+	if (cell == NULL)
+		return -ENODEV;
+	pdata = cell->mfd_data;
+	if (pdata == NULL)
+		return -EINVAL;
+
+	for (i = 0; i < ARRAY_SIZE(pm8607_regulator_info); i++) {
+		info = &pm8607_regulator_info[i];
+		if (!strcmp(info->desc.name, pdata->constraints.name))
+			break;
+	}
+	if (i > ARRAY_SIZE(pm8607_regulator_info)) {
+		dev_err(&pdev->dev, "Failed to find regulator %s\n",
+			pdata->constraints.name);
 		return -EINVAL;
 	}
 
 	info->i2c = (chip->id == CHIP_PM8607) ? chip->client : chip->companion;
 	info->chip = chip;
 
+	/* check DVC ramp slope double */
+	if (!strcmp(info->desc.name, "BUCK3"))
+		if (info->chip->buck3_double)
+			info->slope_double = 1;
+
 	info->regulator = regulator_register(&info->desc, &pdev->dev,
-					     pdata->regulator[pdev->id], info);
+					     pdata, info);
 	if (IS_ERR(info->regulator)) {
 		dev_err(&pdev->dev, "failed to register regulator %s\n",
 			info->desc.name);
 		return PTR_ERR(info->regulator);
 	}
 
-	/* check DVC ramp slope double */
-	if (info->desc.id == PM8607_ID_BUCK3)
-		if (info->chip->buck3_double)
-			info->slope_double = 1;
-
 	platform_set_drvdata(pdev, info);
 	return 0;
 }
diff --git a/drivers/regulator/Kconfig b/drivers/regulator/Kconfig
index e1d9436..de75f67 100644
--- a/drivers/regulator/Kconfig
+++ b/drivers/regulator/Kconfig
@@ -108,6 +108,15 @@
 	  via I2C bus. Maxim 8952 has one voltage output and supports 4 DVS
 	  modes ranging from 0.77V to 1.40V by 0.01V steps.
 
+config REGULATOR_MAX8997
+	tristate "Maxim 8997/8966 regulator"
+	depends on MFD_MAX8997
+	help
+	  This driver controls a Maxim 8997/8966 regulator
+	  via I2C bus. The provided regulator is suitable for S5PC110,
+	  S5PV210, and Exynos-4 chips to control VCC_CORE and
+	  VCC_USIM voltages.
+
 config REGULATOR_MAX8998
 	tristate "Maxim 8998 voltage regulator"
 	depends on MFD_MAX8998
@@ -214,6 +223,15 @@
 	 AB3100 analog baseband dealing with power regulators
 	 for the system.
 
+config REGULATOR_TPS6105X
+	tristate "TI TPS6105X Power regulators"
+	depends on TPS6105X
+	default y if TPS6105X
+	help
+	  This driver supports TPS61050/TPS61052 voltage regulator chips.
+	  It is a single boost converter primarily for white LEDs and
+	  audio amplifiers.
+
 config REGULATOR_TPS65023
 	tristate "TI TPS65023 Power regulators"
 	depends on I2C
diff --git a/drivers/regulator/Makefile b/drivers/regulator/Makefile
index 0b5e88c..d72a427 100644
--- a/drivers/regulator/Makefile
+++ b/drivers/regulator/Makefile
@@ -18,6 +18,7 @@
 obj-$(CONFIG_REGULATOR_MAX8660) += max8660.o
 obj-$(CONFIG_REGULATOR_MAX8925) += max8925-regulator.o
 obj-$(CONFIG_REGULATOR_MAX8952) += max8952.o
+obj-$(CONFIG_REGULATOR_MAX8997) += max8997.o
 obj-$(CONFIG_REGULATOR_MAX8998) += max8998.o
 obj-$(CONFIG_REGULATOR_WM831X) += wm831x-dcdc.o
 obj-$(CONFIG_REGULATOR_WM831X) += wm831x-isink.o
@@ -33,7 +34,7 @@
 obj-$(CONFIG_REGULATOR_MC13892) += mc13892-regulator.o
 obj-$(CONFIG_REGULATOR_MC13XXX_CORE) +=  mc13xxx-regulator-core.o
 obj-$(CONFIG_REGULATOR_AB3100) += ab3100.o
-
+obj-$(CONFIG_REGULATOR_TPS6105X) += tps6105x-regulator.o
 obj-$(CONFIG_REGULATOR_TPS65023) += tps65023-regulator.o
 obj-$(CONFIG_REGULATOR_TPS6507X) += tps6507x-regulator.o
 obj-$(CONFIG_REGULATOR_TPS6524X) += tps6524x-regulator.o
diff --git a/drivers/regulator/ab3100.c b/drivers/regulator/ab3100.c
index ed6feaf..2dec589 100644
--- a/drivers/regulator/ab3100.c
+++ b/drivers/regulator/ab3100.c
@@ -17,6 +17,7 @@
 #include <linux/platform_device.h>
 #include <linux/regulator/driver.h>
 #include <linux/mfd/abx500.h>
+#include <linux/mfd/core.h>
 
 /* LDO registers and some handy masking definitions for AB3100 */
 #define AB3100_LDO_A		0x40
@@ -576,7 +577,7 @@
 
 static int __devinit ab3100_regulators_probe(struct platform_device *pdev)
 {
-	struct ab3100_platform_data *plfdata = pdev->dev.platform_data;
+	struct ab3100_platform_data *plfdata = mfd_get_data(pdev);
 	int err = 0;
 	u8 data;
 	int i;
diff --git a/drivers/regulator/max8997.c b/drivers/regulator/max8997.c
new file mode 100644
index 0000000..01ef7e9
--- /dev/null
+++ b/drivers/regulator/max8997.c
@@ -0,0 +1,1213 @@
+/*
+ * max8997.c - Regulator driver for the Maxim 8997/8966
+ *
+ * Copyright (C) 2011 Samsung Electronics
+ * MyungJoo Ham <myungjoo.ham@smasung.com>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA  02111-1307  USA
+ *
+ * This driver is based on max8998.c
+ */
+
+#include <linux/bug.h>
+#include <linux/delay.h>
+#include <linux/err.h>
+#include <linux/gpio.h>
+#include <linux/slab.h>
+#include <linux/platform_device.h>
+#include <linux/regulator/driver.h>
+#include <linux/regulator/machine.h>
+#include <linux/mfd/max8997.h>
+#include <linux/mfd/max8997-private.h>
+
+struct max8997_data {
+	struct device *dev;
+	struct max8997_dev *iodev;
+	int num_regulators;
+	struct regulator_dev **rdev;
+	int ramp_delay; /* in mV/us */
+
+	u8 buck1_vol[8];
+	u8 buck2_vol[8];
+	u8 buck5_vol[8];
+	int buck125_gpioindex;
+
+	u8 saved_states[MAX8997_REG_MAX];
+};
+
+static inline void max8997_set_gpio(struct max8997_data *max8997)
+{
+	struct max8997_platform_data *pdata =
+		dev_get_platdata(max8997->iodev->dev);
+	int set3 = (max8997->buck125_gpioindex) & 0x1;
+	int set2 = ((max8997->buck125_gpioindex) >> 1) & 0x1;
+	int set1 = ((max8997->buck125_gpioindex) >> 2) & 0x1;
+
+	gpio_set_value(pdata->buck125_gpios[0], set1);
+	gpio_set_value(pdata->buck125_gpios[1], set2);
+	gpio_set_value(pdata->buck125_gpios[2], set3);
+}
+
+struct voltage_map_desc {
+	int min;
+	int max;
+	int step;
+	unsigned int n_bits;
+};
+
+/* Voltage maps in mV */
+static const struct voltage_map_desc ldo_voltage_map_desc = {
+	.min = 800,	.max = 3950,	.step = 50,	.n_bits = 6,
+}; /* LDO1 ~ 18, 21 all */
+
+static const struct voltage_map_desc buck1245_voltage_map_desc = {
+	.min = 650,	.max = 2225,	.step = 25,	.n_bits = 6,
+}; /* Buck1, 2, 4, 5 */
+
+static const struct voltage_map_desc buck37_voltage_map_desc = {
+	.min = 750,	.max = 3900,	.step = 50,	.n_bits = 6,
+}; /* Buck3, 7 */
+
+/* current map in mA */
+static const struct voltage_map_desc charger_current_map_desc = {
+	.min = 200,	.max = 950,	.step = 50,	.n_bits = 4,
+};
+
+static const struct voltage_map_desc topoff_current_map_desc = {
+	.min = 50,	.max = 200,	.step = 10,	.n_bits = 4,
+};
+
+static const struct voltage_map_desc *reg_voltage_map[] = {
+	[MAX8997_LDO1] = &ldo_voltage_map_desc,
+	[MAX8997_LDO2] = &ldo_voltage_map_desc,
+	[MAX8997_LDO3] = &ldo_voltage_map_desc,
+	[MAX8997_LDO4] = &ldo_voltage_map_desc,
+	[MAX8997_LDO5] = &ldo_voltage_map_desc,
+	[MAX8997_LDO6] = &ldo_voltage_map_desc,
+	[MAX8997_LDO7] = &ldo_voltage_map_desc,
+	[MAX8997_LDO8] = &ldo_voltage_map_desc,
+	[MAX8997_LDO9] = &ldo_voltage_map_desc,
+	[MAX8997_LDO10] = &ldo_voltage_map_desc,
+	[MAX8997_LDO11] = &ldo_voltage_map_desc,
+	[MAX8997_LDO12] = &ldo_voltage_map_desc,
+	[MAX8997_LDO13] = &ldo_voltage_map_desc,
+	[MAX8997_LDO14] = &ldo_voltage_map_desc,
+	[MAX8997_LDO15] = &ldo_voltage_map_desc,
+	[MAX8997_LDO16] = &ldo_voltage_map_desc,
+	[MAX8997_LDO17] = &ldo_voltage_map_desc,
+	[MAX8997_LDO18] = &ldo_voltage_map_desc,
+	[MAX8997_LDO21] = &ldo_voltage_map_desc,
+	[MAX8997_BUCK1] = &buck1245_voltage_map_desc,
+	[MAX8997_BUCK2] = &buck1245_voltage_map_desc,
+	[MAX8997_BUCK3] = &buck37_voltage_map_desc,
+	[MAX8997_BUCK4] = &buck1245_voltage_map_desc,
+	[MAX8997_BUCK5] = &buck1245_voltage_map_desc,
+	[MAX8997_BUCK6] = NULL,
+	[MAX8997_BUCK7] = &buck37_voltage_map_desc,
+	[MAX8997_EN32KHZ_AP] = NULL,
+	[MAX8997_EN32KHZ_CP] = NULL,
+	[MAX8997_ENVICHG] = NULL,
+	[MAX8997_ESAFEOUT1] = NULL,
+	[MAX8997_ESAFEOUT2] = NULL,
+	[MAX8997_CHARGER_CV] = NULL,
+	[MAX8997_CHARGER] = &charger_current_map_desc,
+	[MAX8997_CHARGER_TOPOFF] = &topoff_current_map_desc,
+};
+
+static inline int max8997_get_rid(struct regulator_dev *rdev)
+{
+	return rdev_get_id(rdev);
+}
+
+static int max8997_list_voltage_safeout(struct regulator_dev *rdev,
+		unsigned int selector)
+{
+	int rid = max8997_get_rid(rdev);
+
+	if (rid == MAX8997_ESAFEOUT1 || rid == MAX8997_ESAFEOUT2) {
+		switch (selector) {
+		case 0:
+			return 4850000;
+		case 1:
+			return 4900000;
+		case 2:
+			return 4950000;
+		case 3:
+			return 3300000;
+		default:
+			return -EINVAL;
+		}
+	}
+
+	return -EINVAL;
+}
+
+static int max8997_list_voltage_charger_cv(struct regulator_dev *rdev,
+		unsigned int selector)
+{
+	int rid = max8997_get_rid(rdev);
+
+	if (rid != MAX8997_CHARGER_CV)
+		goto err;
+
+	switch (selector) {
+	case 0x00:
+		return 4200000;
+	case 0x01 ... 0x0E:
+		return 4000000 + 20000 * (selector - 0x01);
+	case 0x0F:
+		return 4350000;
+	default:
+		return -EINVAL;
+	}
+err:
+	return -EINVAL;
+}
+
+static int max8997_list_voltage(struct regulator_dev *rdev,
+		unsigned int selector)
+{
+	const struct voltage_map_desc *desc;
+	int rid = max8997_get_rid(rdev);
+	int val;
+
+	if (rid >= ARRAY_SIZE(reg_voltage_map) ||
+			rid < 0)
+		return -EINVAL;
+
+	desc = reg_voltage_map[rid];
+	if (desc == NULL)
+		return -EINVAL;
+
+	val = desc->min + desc->step * selector;
+	if (val > desc->max)
+		return -EINVAL;
+
+	return val * 1000;
+}
+
+static int max8997_get_enable_register(struct regulator_dev *rdev,
+		int *reg, int *mask, int *pattern)
+{
+	int rid = max8997_get_rid(rdev);
+
+	switch (rid) {
+	case MAX8997_LDO1 ... MAX8997_LDO21:
+		*reg = MAX8997_REG_LDO1CTRL + (rid - MAX8997_LDO1);
+		*mask = 0xC0;
+		*pattern = 0xC0;
+		break;
+	case MAX8997_BUCK1:
+		*reg = MAX8997_REG_BUCK1CTRL;
+		*mask = 0x01;
+		*pattern = 0x01;
+		break;
+	case MAX8997_BUCK2:
+		*reg = MAX8997_REG_BUCK2CTRL;
+		*mask = 0x01;
+		*pattern = 0x01;
+		break;
+	case MAX8997_BUCK3:
+		*reg = MAX8997_REG_BUCK3CTRL;
+		*mask = 0x01;
+		*pattern = 0x01;
+		break;
+	case MAX8997_BUCK4:
+		*reg = MAX8997_REG_BUCK4CTRL;
+		*mask = 0x01;
+		*pattern = 0x01;
+		break;
+	case MAX8997_BUCK5:
+		*reg = MAX8997_REG_BUCK5CTRL;
+		*mask = 0x01;
+		*pattern = 0x01;
+		break;
+	case MAX8997_BUCK6:
+		*reg = MAX8997_REG_BUCK6CTRL;
+		*mask = 0x01;
+		*pattern = 0x01;
+		break;
+	case MAX8997_BUCK7:
+		*reg = MAX8997_REG_BUCK7CTRL;
+		*mask = 0x01;
+		*pattern = 0x01;
+		break;
+	case MAX8997_EN32KHZ_AP ... MAX8997_EN32KHZ_CP:
+		*reg = MAX8997_REG_MAINCON1;
+		*mask = 0x01 << (rid - MAX8997_EN32KHZ_AP);
+		*pattern = 0x01 << (rid - MAX8997_EN32KHZ_AP);
+		break;
+	case MAX8997_ENVICHG:
+		*reg = MAX8997_REG_MBCCTRL1;
+		*mask = 0x80;
+		*pattern = 0x80;
+		break;
+	case MAX8997_ESAFEOUT1 ... MAX8997_ESAFEOUT2:
+		*reg = MAX8997_REG_SAFEOUTCTRL;
+		*mask = 0x40 << (rid - MAX8997_ESAFEOUT1);
+		*pattern = 0x40 << (rid - MAX8997_ESAFEOUT1);
+		break;
+	case MAX8997_CHARGER:
+		*reg = MAX8997_REG_MBCCTRL2;
+		*mask = 0x40;
+		*pattern = 0x40;
+		break;
+	default:
+		/* Not controllable or not exists */
+		return -EINVAL;
+		break;
+	}
+
+	return 0;
+}
+
+static int max8997_reg_is_enabled(struct regulator_dev *rdev)
+{
+	struct max8997_data *max8997 = rdev_get_drvdata(rdev);
+	struct i2c_client *i2c = max8997->iodev->i2c;
+	int ret, reg, mask, pattern;
+	u8 val;
+
+	ret = max8997_get_enable_register(rdev, &reg, &mask, &pattern);
+	if (ret == -EINVAL)
+		return 1; /* "not controllable" */
+	else if (ret)
+		return ret;
+
+	ret = max8997_read_reg(i2c, reg, &val);
+	if (ret)
+		return ret;
+
+	return (val & mask) == pattern;
+}
+
+static int max8997_reg_enable(struct regulator_dev *rdev)
+{
+	struct max8997_data *max8997 = rdev_get_drvdata(rdev);
+	struct i2c_client *i2c = max8997->iodev->i2c;
+	int ret, reg, mask, pattern;
+
+	ret = max8997_get_enable_register(rdev, &reg, &mask, &pattern);
+	if (ret)
+		return ret;
+
+	return max8997_update_reg(i2c, reg, pattern, mask);
+}
+
+static int max8997_reg_disable(struct regulator_dev *rdev)
+{
+	struct max8997_data *max8997 = rdev_get_drvdata(rdev);
+	struct i2c_client *i2c = max8997->iodev->i2c;
+	int ret, reg, mask, pattern;
+
+	ret = max8997_get_enable_register(rdev, &reg, &mask, &pattern);
+	if (ret)
+		return ret;
+
+	return max8997_update_reg(i2c, reg, ~pattern, mask);
+}
+
+static int max8997_get_voltage_register(struct regulator_dev *rdev,
+		int *_reg, int *_shift, int *_mask)
+{
+	int rid = max8997_get_rid(rdev);
+	int reg, shift = 0, mask = 0x3f;
+
+	switch (rid) {
+	case MAX8997_LDO1 ... MAX8997_LDO21:
+		reg = MAX8997_REG_LDO1CTRL + (rid - MAX8997_LDO1);
+		break;
+	case MAX8997_BUCK1:
+		reg = MAX8997_REG_BUCK1DVS1;
+		break;
+	case MAX8997_BUCK2:
+		reg = MAX8997_REG_BUCK2DVS1;
+		break;
+	case MAX8997_BUCK3:
+		reg = MAX8997_REG_BUCK3DVS;
+		break;
+	case MAX8997_BUCK4:
+		reg = MAX8997_REG_BUCK4DVS;
+		break;
+	case MAX8997_BUCK5:
+		reg = MAX8997_REG_BUCK5DVS1;
+		break;
+	case MAX8997_BUCK7:
+		reg = MAX8997_REG_BUCK7DVS;
+		break;
+	case MAX8997_ESAFEOUT1 ...  MAX8997_ESAFEOUT2:
+		reg = MAX8997_REG_SAFEOUTCTRL;
+		shift = (rid == MAX8997_ESAFEOUT2) ? 2 : 0;
+		mask = 0x3;
+		break;
+	case MAX8997_CHARGER_CV:
+		reg = MAX8997_REG_MBCCTRL3;
+		shift = 0;
+		mask = 0xf;
+		break;
+	case MAX8997_CHARGER:
+		reg = MAX8997_REG_MBCCTRL4;
+		shift = 0;
+		mask = 0xf;
+		break;
+	case MAX8997_CHARGER_TOPOFF:
+		reg = MAX8997_REG_MBCCTRL5;
+		shift = 0;
+		mask = 0xf;
+		break;
+	default:
+		return -EINVAL;
+	}
+
+	*_reg = reg;
+	*_shift = shift;
+	*_mask = mask;
+
+	return 0;
+}
+
+static int max8997_get_voltage(struct regulator_dev *rdev)
+{
+	struct max8997_data *max8997 = rdev_get_drvdata(rdev);
+	struct max8997_platform_data *pdata =
+		dev_get_platdata(max8997->iodev->dev);
+	struct i2c_client *i2c = max8997->iodev->i2c;
+	int reg, shift, mask, ret;
+	int rid = max8997_get_rid(rdev);
+	u8 val;
+
+	ret = max8997_get_voltage_register(rdev, &reg, &shift, &mask);
+	if (ret)
+		return ret;
+
+	if ((rid == MAX8997_BUCK1 && pdata->buck1_gpiodvs) ||
+			(rid == MAX8997_BUCK2 && pdata->buck2_gpiodvs) ||
+			(rid == MAX8997_BUCK5 && pdata->buck5_gpiodvs))
+		reg += max8997->buck125_gpioindex;
+
+	ret = max8997_read_reg(i2c, reg, &val);
+	if (ret)
+		return ret;
+
+	val >>= shift;
+	val &= mask;
+
+	if (rdev->desc && rdev->desc->ops && rdev->desc->ops->list_voltage)
+		return rdev->desc->ops->list_voltage(rdev, val);
+
+	/*
+	 * max8997_list_voltage returns value for any rdev with voltage_map,
+	 * which works for "CHARGER" and "CHARGER TOPOFF" that do not have
+	 * list_voltage ops (they are current regulators).
+	 */
+	return max8997_list_voltage(rdev, val);
+}
+
+static inline int max8997_get_voltage_proper_val(
+		const struct voltage_map_desc *desc,
+		int min_vol, int max_vol)
+{
+	int i = 0;
+
+	if (desc == NULL)
+		return -EINVAL;
+
+	if (max_vol < desc->min || min_vol > desc->max)
+		return -EINVAL;
+
+	while (desc->min + desc->step * i < min_vol &&
+			desc->min + desc->step * i < desc->max)
+		i++;
+
+	if (desc->min + desc->step * i > max_vol)
+		return -EINVAL;
+
+	if (i >= (1 << desc->n_bits))
+		return -EINVAL;
+
+	return i;
+}
+
+static int max8997_set_voltage_charger_cv(struct regulator_dev *rdev,
+		int min_uV, int max_uV, unsigned *selector)
+{
+	struct max8997_data *max8997 = rdev_get_drvdata(rdev);
+	struct i2c_client *i2c = max8997->iodev->i2c;
+	int rid = max8997_get_rid(rdev);
+	int lb, ub;
+	int reg, shift = 0, mask, ret = 0;
+	u8 val = 0x0;
+
+	if (rid != MAX8997_CHARGER_CV)
+		return -EINVAL;
+
+	ret = max8997_get_voltage_register(rdev, &reg, &shift, &mask);
+	if (ret)
+		return ret;
+
+	if (max_uV < 4000000 || min_uV > 4350000)
+		return -EINVAL;
+
+	if (min_uV <= 4000000) {
+		if (max_uV >= 4000000)
+			return -EINVAL;
+		else
+			val = 0x1;
+	} else if (min_uV <= 4200000 && max_uV >= 4200000)
+		val = 0x0;
+	else {
+		lb = (min_uV - 4000001) / 20000 + 2;
+		ub = (max_uV - 4000000) / 20000 + 1;
+
+		if (lb > ub)
+			return -EINVAL;
+
+		if (lb < 0xf)
+			val = lb;
+		else {
+			if (ub >= 0xf)
+				val = 0xf;
+			else
+				return -EINVAL;
+		}
+	}
+
+	*selector = val;
+
+	ret = max8997_update_reg(i2c, reg, val << shift, mask);
+
+	return ret;
+}
+
+/*
+ * For LDO1 ~ LDO21, BUCK1~5, BUCK7, CHARGER, CHARGER_TOPOFF
+ * BUCK1, 2, and 5 are available if they are not controlled by gpio
+ */
+static int max8997_set_voltage_ldobuck(struct regulator_dev *rdev,
+		int min_uV, int max_uV, unsigned *selector)
+{
+	struct max8997_data *max8997 = rdev_get_drvdata(rdev);
+	struct i2c_client *i2c = max8997->iodev->i2c;
+	int min_vol = min_uV / 1000, max_vol = max_uV / 1000;
+	const struct voltage_map_desc *desc;
+	int rid = max8997_get_rid(rdev);
+	int reg, shift = 0, mask, ret;
+	int i;
+	u8 org;
+
+	switch (rid) {
+	case MAX8997_LDO1 ... MAX8997_LDO21:
+		break;
+	case MAX8997_BUCK1 ... MAX8997_BUCK5:
+		break;
+	case MAX8997_BUCK6:
+		return -EINVAL;
+	case MAX8997_BUCK7:
+		break;
+	case MAX8997_CHARGER:
+		break;
+	case MAX8997_CHARGER_TOPOFF:
+		break;
+	default:
+		return -EINVAL;
+	}
+
+	desc = reg_voltage_map[rid];
+
+	i = max8997_get_voltage_proper_val(desc, min_vol, max_vol);
+	if (i < 0)
+		return i;
+
+	ret = max8997_get_voltage_register(rdev, &reg, &shift, &mask);
+	if (ret)
+		return ret;
+
+	max8997_read_reg(i2c, reg, &org);
+	org = (org & mask) >> shift;
+
+	ret = max8997_update_reg(i2c, reg, i << shift, mask << shift);
+	*selector = i;
+
+	if (rid == MAX8997_BUCK1 || rid == MAX8997_BUCK2 ||
+			rid == MAX8997_BUCK4 || rid == MAX8997_BUCK5) {
+		/* If the voltage is increasing */
+		if (org < i)
+			udelay(desc->step * (i - org) / max8997->ramp_delay);
+	}
+
+	return ret;
+}
+
+/*
+ * Assess the damage on the voltage setting of BUCK1,2,5 by the change.
+ *
+ * When GPIO-DVS mode is used for multiple bucks, changing the voltage value
+ * of one of the bucks may affect that of another buck, which is the side
+ * effect of the change (set_voltage). This function examines the GPIO-DVS
+ * configurations and checks whether such side-effect exists.
+ */
+static int max8997_assess_side_effect(struct regulator_dev *rdev,
+		u8 new_val, int *best)
+{
+	struct max8997_data *max8997 = rdev_get_drvdata(rdev);
+	struct max8997_platform_data *pdata =
+		dev_get_platdata(max8997->iodev->dev);
+	int rid = max8997_get_rid(rdev);
+	u8 *buckx_val[3];
+	bool buckx_gpiodvs[3];
+	int side_effect[8];
+	int min_side_effect = INT_MAX;
+	int i;
+
+	*best = -1;
+
+	switch (rid) {
+	case MAX8997_BUCK1:
+		rid = 0;
+		break;
+	case MAX8997_BUCK2:
+		rid = 1;
+		break;
+	case MAX8997_BUCK5:
+		rid = 2;
+		break;
+	default:
+		return -EINVAL;
+	}
+
+	buckx_val[0] = max8997->buck1_vol;
+	buckx_val[1] = max8997->buck2_vol;
+	buckx_val[2] = max8997->buck5_vol;
+	buckx_gpiodvs[0] = pdata->buck1_gpiodvs;
+	buckx_gpiodvs[1] = pdata->buck2_gpiodvs;
+	buckx_gpiodvs[2] = pdata->buck5_gpiodvs;
+
+	for (i = 0; i < 8; i++) {
+		int others;
+
+		if (new_val != (buckx_val[rid])[i]) {
+			side_effect[i] = -1;
+			continue;
+		}
+
+		side_effect[i] = 0;
+		for (others = 0; others < 3; others++) {
+			int diff;
+
+			if (others == rid)
+				continue;
+			if (buckx_gpiodvs[others] == false)
+				continue; /* Not affected */
+			diff = (buckx_val[others])[i] -
+				(buckx_val[others])[max8997->buck125_gpioindex];
+			if (diff > 0)
+				side_effect[i] += diff;
+			else if (diff < 0)
+				side_effect[i] -= diff;
+		}
+		if (side_effect[i] == 0) {
+			*best = i;
+			return 0; /* NO SIDE EFFECT! Use This! */
+		}
+		if (side_effect[i] < min_side_effect) {
+			min_side_effect = side_effect[i];
+			*best = i;
+		}
+	}
+
+	if (*best == -1)
+		return -EINVAL;
+
+	return side_effect[*best];
+}
+
+/*
+ * For Buck 1 ~ 5 and 7. If it is not controlled by GPIO, this calls
+ * max8997_set_voltage_ldobuck to do the job.
+ */
+static int max8997_set_voltage_buck(struct regulator_dev *rdev,
+		int min_uV, int max_uV, unsigned *selector)
+{
+	struct max8997_data *max8997 = rdev_get_drvdata(rdev);
+	struct max8997_platform_data *pdata =
+		dev_get_platdata(max8997->iodev->dev);
+	int rid = max8997_get_rid(rdev);
+	const struct voltage_map_desc *desc;
+	int new_val, new_idx, damage, tmp_val, tmp_idx, tmp_dmg;
+	bool gpio_dvs_mode = false;
+	int min_vol = min_uV / 1000, max_vol = max_uV / 1000;
+
+	if (rid < MAX8997_BUCK1 || rid > MAX8997_BUCK7)
+		return -EINVAL;
+
+	switch (rid) {
+	case MAX8997_BUCK1:
+		if (pdata->buck1_gpiodvs)
+			gpio_dvs_mode = true;
+		break;
+	case MAX8997_BUCK2:
+		if (pdata->buck2_gpiodvs)
+			gpio_dvs_mode = true;
+		break;
+	case MAX8997_BUCK5:
+		if (pdata->buck5_gpiodvs)
+			gpio_dvs_mode = true;
+		break;
+	}
+
+	if (!gpio_dvs_mode)
+		return max8997_set_voltage_ldobuck(rdev, min_uV, max_uV,
+						selector);
+
+	desc = reg_voltage_map[rid];
+	new_val = max8997_get_voltage_proper_val(desc, min_vol, max_vol);
+	if (new_val < 0)
+		return new_val;
+
+	tmp_dmg = INT_MAX;
+	tmp_idx = -1;
+	tmp_val = -1;
+	do {
+		damage = max8997_assess_side_effect(rdev, new_val, &new_idx);
+		if (damage == 0)
+			goto out;
+
+		if (tmp_dmg > damage) {
+			tmp_idx = new_idx;
+			tmp_val = new_val;
+			tmp_dmg = damage;
+		}
+
+		new_val++;
+	} while (desc->min + desc->step + new_val <= desc->max);
+
+	new_idx = tmp_idx;
+	new_val = tmp_val;
+
+	if (pdata->ignore_gpiodvs_side_effect == false)
+		return -EINVAL;
+
+	dev_warn(&rdev->dev, "MAX8997 GPIO-DVS Side Effect Warning: GPIO SET:"
+			" %d -> %d\n", max8997->buck125_gpioindex, tmp_idx);
+
+out:
+	if (new_idx < 0 || new_val < 0)
+		return -EINVAL;
+
+	max8997->buck125_gpioindex = new_idx;
+	max8997_set_gpio(max8997);
+	*selector = new_val;
+
+	return 0;
+}
+
+static const int safeoutvolt[] = {
+	3300000,
+	4850000,
+	4900000,
+	4950000,
+};
+
+/* For SAFEOUT1 and SAFEOUT2 */
+static int max8997_set_voltage_safeout(struct regulator_dev *rdev,
+		int min_uV, int max_uV, unsigned *selector)
+{
+	struct max8997_data *max8997 = rdev_get_drvdata(rdev);
+	struct i2c_client *i2c = max8997->iodev->i2c;
+	int rid = max8997_get_rid(rdev);
+	int reg, shift = 0, mask, ret;
+	int i = 0;
+	u8 val;
+
+	if (rid != MAX8997_ESAFEOUT1 && rid != MAX8997_ESAFEOUT2)
+		return -EINVAL;
+
+	for (i = 0; i < ARRAY_SIZE(safeoutvolt); i++) {
+		if (min_uV <= safeoutvolt[i] &&
+				max_uV >= safeoutvolt[i])
+			break;
+	}
+
+	if (i >= ARRAY_SIZE(safeoutvolt))
+		return -EINVAL;
+
+	if (i == 0)
+		val = 0x3;
+	else
+		val = i - 1;
+
+	ret = max8997_get_voltage_register(rdev, &reg, &shift, &mask);
+	if (ret)
+		return ret;
+
+	ret = max8997_update_reg(i2c, reg, val << shift, mask << shift);
+	*selector = val;
+
+	return ret;
+}
+
+static int max8997_reg_enable_suspend(struct regulator_dev *rdev)
+{
+	return 0;
+}
+
+static int max8997_reg_disable_suspend(struct regulator_dev *rdev)
+{
+	struct max8997_data *max8997 = rdev_get_drvdata(rdev);
+	struct i2c_client *i2c = max8997->iodev->i2c;
+	int ret, reg, mask, pattern;
+	int rid = max8997_get_rid(rdev);
+
+	ret = max8997_get_enable_register(rdev, &reg, &mask, &pattern);
+	if (ret)
+		return ret;
+
+	max8997_read_reg(i2c, reg, &max8997->saved_states[rid]);
+
+	if (rid == MAX8997_LDO1 ||
+			rid == MAX8997_LDO10 ||
+			rid == MAX8997_LDO21) {
+		dev_dbg(&rdev->dev, "Conditional Power-Off for %s\n",
+				rdev->desc->name);
+		return max8997_update_reg(i2c, reg, 0x40, mask);
+	}
+
+	dev_dbg(&rdev->dev, "Full Power-Off for %s (%xh -> %xh)\n",
+			rdev->desc->name, max8997->saved_states[rid] & mask,
+			(~pattern) & mask);
+	return max8997_update_reg(i2c, reg, ~pattern, mask);
+}
+
+static struct regulator_ops max8997_ldo_ops = {
+	.list_voltage		= max8997_list_voltage,
+	.is_enabled		= max8997_reg_is_enabled,
+	.enable			= max8997_reg_enable,
+	.disable		= max8997_reg_disable,
+	.get_voltage		= max8997_get_voltage,
+	.set_voltage		= max8997_set_voltage_ldobuck,
+	.set_suspend_enable	= max8997_reg_enable_suspend,
+	.set_suspend_disable	= max8997_reg_disable_suspend,
+};
+
+static struct regulator_ops max8997_buck_ops = {
+	.list_voltage		= max8997_list_voltage,
+	.is_enabled		= max8997_reg_is_enabled,
+	.enable			= max8997_reg_enable,
+	.disable		= max8997_reg_disable,
+	.get_voltage		= max8997_get_voltage,
+	.set_voltage		= max8997_set_voltage_buck,
+	.set_suspend_enable	= max8997_reg_enable_suspend,
+	.set_suspend_disable	= max8997_reg_disable_suspend,
+};
+
+static struct regulator_ops max8997_fixedvolt_ops = {
+	.list_voltage		= max8997_list_voltage,
+	.is_enabled		= max8997_reg_is_enabled,
+	.enable			= max8997_reg_enable,
+	.disable		= max8997_reg_disable,
+	.set_suspend_enable	= max8997_reg_enable_suspend,
+	.set_suspend_disable	= max8997_reg_disable_suspend,
+};
+
+static struct regulator_ops max8997_safeout_ops = {
+	.list_voltage		= max8997_list_voltage_safeout,
+	.is_enabled		= max8997_reg_is_enabled,
+	.enable			= max8997_reg_enable,
+	.disable		= max8997_reg_disable,
+	.get_voltage		= max8997_get_voltage,
+	.set_voltage		= max8997_set_voltage_safeout,
+	.set_suspend_enable	= max8997_reg_enable_suspend,
+	.set_suspend_disable	= max8997_reg_disable_suspend,
+};
+
+static struct regulator_ops max8997_fixedstate_ops = {
+	.list_voltage		= max8997_list_voltage_charger_cv,
+	.get_voltage		= max8997_get_voltage,
+	.set_voltage		= max8997_set_voltage_charger_cv,
+};
+
+static int max8997_set_voltage_ldobuck_wrap(struct regulator_dev *rdev,
+		int min_uV, int max_uV)
+{
+	unsigned dummy;
+
+	return max8997_set_voltage_ldobuck(rdev, min_uV, max_uV, &dummy);
+}
+
+
+static struct regulator_ops max8997_charger_ops = {
+	.is_enabled		= max8997_reg_is_enabled,
+	.enable			= max8997_reg_enable,
+	.disable		= max8997_reg_disable,
+	.get_current_limit	= max8997_get_voltage,
+	.set_current_limit	= max8997_set_voltage_ldobuck_wrap,
+};
+
+static struct regulator_ops max8997_charger_fixedstate_ops = {
+	.is_enabled		= max8997_reg_is_enabled,
+	.get_current_limit	= max8997_get_voltage,
+	.set_current_limit	= max8997_set_voltage_ldobuck_wrap,
+};
+
+#define regulator_desc_ldo(num)		{	\
+	.name		= "LDO"#num,		\
+	.id		= MAX8997_LDO##num,	\
+	.ops		= &max8997_ldo_ops,	\
+	.type		= REGULATOR_VOLTAGE,	\
+	.owner		= THIS_MODULE,		\
+}
+#define regulator_desc_buck(num)		{	\
+	.name		= "BUCK"#num,		\
+	.id		= MAX8997_BUCK##num,	\
+	.ops		= &max8997_buck_ops,	\
+	.type		= REGULATOR_VOLTAGE,	\
+	.owner		= THIS_MODULE,		\
+}
+
+static struct regulator_desc regulators[] = {
+	regulator_desc_ldo(1),
+	regulator_desc_ldo(2),
+	regulator_desc_ldo(3),
+	regulator_desc_ldo(4),
+	regulator_desc_ldo(5),
+	regulator_desc_ldo(6),
+	regulator_desc_ldo(7),
+	regulator_desc_ldo(8),
+	regulator_desc_ldo(9),
+	regulator_desc_ldo(10),
+	regulator_desc_ldo(11),
+	regulator_desc_ldo(12),
+	regulator_desc_ldo(13),
+	regulator_desc_ldo(14),
+	regulator_desc_ldo(15),
+	regulator_desc_ldo(16),
+	regulator_desc_ldo(17),
+	regulator_desc_ldo(18),
+	regulator_desc_ldo(21),
+	regulator_desc_buck(1),
+	regulator_desc_buck(2),
+	regulator_desc_buck(3),
+	regulator_desc_buck(4),
+	regulator_desc_buck(5),
+	{
+		.name	= "BUCK6",
+		.id	= MAX8997_BUCK6,
+		.ops	= &max8997_fixedvolt_ops,
+		.type	= REGULATOR_VOLTAGE,
+		.owner	= THIS_MODULE,
+	},
+	regulator_desc_buck(7),
+	{
+		.name	= "EN32KHz AP",
+		.id	= MAX8997_EN32KHZ_AP,
+		.ops	= &max8997_fixedvolt_ops,
+		.type	= REGULATOR_VOLTAGE,
+		.owner	= THIS_MODULE,
+	}, {
+		.name	= "EN32KHz CP",
+		.id	= MAX8997_EN32KHZ_CP,
+		.ops	= &max8997_fixedvolt_ops,
+		.type	= REGULATOR_VOLTAGE,
+		.owner	= THIS_MODULE,
+	}, {
+		.name	= "ENVICHG",
+		.id	= MAX8997_ENVICHG,
+		.ops	= &max8997_fixedvolt_ops,
+		.type	= REGULATOR_VOLTAGE,
+		.owner	= THIS_MODULE,
+	}, {
+		.name	= "ESAFEOUT1",
+		.id	= MAX8997_ESAFEOUT1,
+		.ops	= &max8997_safeout_ops,
+		.type	= REGULATOR_VOLTAGE,
+		.owner	 = THIS_MODULE,
+	}, {
+		.name	= "ESAFEOUT2",
+		.id	= MAX8997_ESAFEOUT2,
+		.ops	= &max8997_safeout_ops,
+		.type	= REGULATOR_VOLTAGE,
+		.owner	 = THIS_MODULE,
+	}, {
+		.name	= "CHARGER CV",
+		.id	= MAX8997_CHARGER_CV,
+		.ops	= &max8997_fixedstate_ops,
+		.type	= REGULATOR_VOLTAGE,
+		.owner	 = THIS_MODULE,
+	}, {
+		.name	= "CHARGER",
+		.id	= MAX8997_CHARGER,
+		.ops	= &max8997_charger_ops,
+		.type	= REGULATOR_CURRENT,
+		.owner	 = THIS_MODULE,
+	}, {
+		.name	= "CHARGER TOPOFF",
+		.id	= MAX8997_CHARGER_TOPOFF,
+		.ops	= &max8997_charger_fixedstate_ops,
+		.type	= REGULATOR_CURRENT,
+		.owner	 = THIS_MODULE,
+	},
+};
+
+static __devinit int max8997_pmic_probe(struct platform_device *pdev)
+{
+	struct max8997_dev *iodev = dev_get_drvdata(pdev->dev.parent);
+	struct max8997_platform_data *pdata = dev_get_platdata(iodev->dev);
+	struct regulator_dev **rdev;
+	struct max8997_data *max8997;
+	struct i2c_client *i2c;
+	int i, ret, size;
+	u8 max_buck1 = 0, max_buck2 = 0, max_buck5 = 0;
+
+	if (!pdata) {
+		dev_err(pdev->dev.parent, "No platform init data supplied.\n");
+		return -ENODEV;
+	}
+
+	max8997 = kzalloc(sizeof(struct max8997_data), GFP_KERNEL);
+	if (!max8997)
+		return -ENOMEM;
+
+	size = sizeof(struct regulator_dev *) * pdata->num_regulators;
+	max8997->rdev = kzalloc(size, GFP_KERNEL);
+	if (!max8997->rdev) {
+		kfree(max8997);
+		return -ENOMEM;
+	}
+
+	rdev = max8997->rdev;
+	max8997->dev = &pdev->dev;
+	max8997->iodev = iodev;
+	max8997->num_regulators = pdata->num_regulators;
+	platform_set_drvdata(pdev, max8997);
+	i2c = max8997->iodev->i2c;
+
+	max8997->buck125_gpioindex = pdata->buck125_default_idx;
+
+	for (i = 0; i < 8; i++) {
+		max8997->buck1_vol[i] = ret =
+			max8997_get_voltage_proper_val(
+					&buck1245_voltage_map_desc,
+					pdata->buck1_voltage[i] / 1000,
+					pdata->buck1_voltage[i] / 1000 +
+					buck1245_voltage_map_desc.step);
+		if (ret < 0)
+			goto err_alloc;
+
+		max8997->buck2_vol[i] = ret =
+			max8997_get_voltage_proper_val(
+					&buck1245_voltage_map_desc,
+					pdata->buck2_voltage[i] / 1000,
+					pdata->buck2_voltage[i] / 1000 +
+					buck1245_voltage_map_desc.step);
+		if (ret < 0)
+			goto err_alloc;
+
+		max8997->buck5_vol[i] = ret =
+			max8997_get_voltage_proper_val(
+					&buck1245_voltage_map_desc,
+					pdata->buck5_voltage[i] / 1000,
+					pdata->buck5_voltage[i] / 1000 +
+					buck1245_voltage_map_desc.step);
+		if (ret < 0)
+			goto err_alloc;
+
+		if (max_buck1 < max8997->buck1_vol[i])
+			max_buck1 = max8997->buck1_vol[i];
+		if (max_buck2 < max8997->buck2_vol[i])
+			max_buck2 = max8997->buck2_vol[i];
+		if (max_buck5 < max8997->buck5_vol[i])
+			max_buck5 = max8997->buck5_vol[i];
+	}
+
+	/* For the safety, set max voltage before setting up */
+	for (i = 0; i < 8; i++) {
+		max8997_update_reg(i2c, MAX8997_REG_BUCK1DVS(i + 1),
+				max_buck1, 0x3f);
+		max8997_update_reg(i2c, MAX8997_REG_BUCK2DVS(i + 1),
+				max_buck2, 0x3f);
+		max8997_update_reg(i2c, MAX8997_REG_BUCK5DVS(i + 1),
+				max_buck5, 0x3f);
+	}
+
+	/*
+	 * If buck 1, 2, and 5 do not care DVS GPIO settings, ignore them.
+	 * If at least one of them cares, set gpios.
+	 */
+	if (pdata->buck1_gpiodvs || pdata->buck2_gpiodvs ||
+			pdata->buck5_gpiodvs) {
+		bool gpio1set = false, gpio2set = false;
+
+		if (!gpio_is_valid(pdata->buck125_gpios[0]) ||
+				!gpio_is_valid(pdata->buck125_gpios[1]) ||
+				!gpio_is_valid(pdata->buck125_gpios[2])) {
+			dev_err(&pdev->dev, "GPIO NOT VALID\n");
+			ret = -EINVAL;
+			goto err_alloc;
+		}
+
+		ret = gpio_request(pdata->buck125_gpios[0],
+				"MAX8997 SET1");
+		if (ret == -EBUSY)
+			dev_warn(&pdev->dev, "Duplicated gpio request"
+					" on SET1\n");
+		else if (ret)
+			goto err_alloc;
+		else
+			gpio1set = true;
+
+		ret = gpio_request(pdata->buck125_gpios[1],
+				"MAX8997 SET2");
+		if (ret == -EBUSY)
+			dev_warn(&pdev->dev, "Duplicated gpio request"
+					" on SET2\n");
+		else if (ret) {
+			if (gpio1set)
+				gpio_free(pdata->buck125_gpios[0]);
+			goto err_alloc;
+		} else
+			gpio2set = true;
+
+		ret = gpio_request(pdata->buck125_gpios[2],
+				"MAX8997 SET3");
+		if (ret == -EBUSY)
+			dev_warn(&pdev->dev, "Duplicated gpio request"
+					" on SET3\n");
+		else if (ret) {
+			if (gpio1set)
+				gpio_free(pdata->buck125_gpios[0]);
+			if (gpio2set)
+				gpio_free(pdata->buck125_gpios[1]);
+			goto err_alloc;
+		}
+
+		gpio_direction_output(pdata->buck125_gpios[0],
+				(max8997->buck125_gpioindex >> 2)
+				& 0x1); /* SET1 */
+		gpio_direction_output(pdata->buck125_gpios[1],
+				(max8997->buck125_gpioindex >> 1)
+				& 0x1); /* SET2 */
+		gpio_direction_output(pdata->buck125_gpios[2],
+				(max8997->buck125_gpioindex >> 0)
+				& 0x1); /* SET3 */
+		ret = 0;
+	}
+
+	/* DVS-GPIO disabled */
+	max8997_update_reg(i2c, MAX8997_REG_BUCK1CTRL, (pdata->buck1_gpiodvs) ?
+			(1 << 1) : (0 << 1), 1 << 1);
+	max8997_update_reg(i2c, MAX8997_REG_BUCK2CTRL, (pdata->buck2_gpiodvs) ?
+			(1 << 1) : (0 << 1), 1 << 1);
+	max8997_update_reg(i2c, MAX8997_REG_BUCK5CTRL, (pdata->buck5_gpiodvs) ?
+			(1 << 1) : (0 << 1), 1 << 1);
+
+	/* Initialize all the DVS related BUCK registers */
+	for (i = 0; i < 8; i++) {
+		max8997_update_reg(i2c, MAX8997_REG_BUCK1DVS(i + 1),
+				max8997->buck1_vol[i],
+				0x3f);
+		max8997_update_reg(i2c, MAX8997_REG_BUCK2DVS(i + 1),
+				max8997->buck2_vol[i],
+				0x3f);
+		max8997_update_reg(i2c, MAX8997_REG_BUCK5DVS(i + 1),
+				max8997->buck5_vol[i],
+				0x3f);
+	}
+
+	for (i = 0; i < pdata->num_regulators; i++) {
+		const struct voltage_map_desc *desc;
+		int id = pdata->regulators[i].id;
+
+		desc = reg_voltage_map[id];
+		if (desc)
+			regulators[id].n_voltages =
+				(desc->max - desc->min) / desc->step + 1;
+		else if (id == MAX8997_ESAFEOUT1 || id == MAX8997_ESAFEOUT2)
+			regulators[id].n_voltages = 4;
+		else if (id == MAX8997_CHARGER_CV)
+			regulators[id].n_voltages = 16;
+
+		rdev[i] = regulator_register(&regulators[id], max8997->dev,
+				pdata->regulators[i].initdata, max8997);
+		if (IS_ERR(rdev[i])) {
+			ret = PTR_ERR(rdev[i]);
+			dev_err(max8997->dev, "regulator init failed for %d\n",
+					id);
+			rdev[i] = NULL;
+			goto err;
+		}
+	}
+
+	/* Misc Settings */
+	max8997->ramp_delay = 10; /* set 10mV/us, which is the default */
+	max8997_write_reg(i2c, MAX8997_REG_BUCKRAMP, (0xf << 4) | 0x9);
+
+	return 0;
+err:
+	for (i = 0; i < max8997->num_regulators; i++)
+		if (rdev[i])
+			regulator_unregister(rdev[i]);
+err_alloc:
+	kfree(max8997->rdev);
+	kfree(max8997);
+
+	return ret;
+}
+
+static int __devexit max8997_pmic_remove(struct platform_device *pdev)
+{
+	struct max8997_data *max8997 = platform_get_drvdata(pdev);
+	struct regulator_dev **rdev = max8997->rdev;
+	int i;
+
+	for (i = 0; i < max8997->num_regulators; i++)
+		if (rdev[i])
+			regulator_unregister(rdev[i]);
+
+	kfree(max8997->rdev);
+	kfree(max8997);
+
+	return 0;
+}
+
+static const struct platform_device_id max8997_pmic_id[] = {
+	{ "max8997-pmic", 0},
+	{ },
+};
+
+static struct platform_driver max8997_pmic_driver = {
+	.driver = {
+		.name = "max8997-pmic",
+		.owner = THIS_MODULE,
+	},
+	.probe = max8997_pmic_probe,
+	.remove = __devexit_p(max8997_pmic_remove),
+	.id_table = max8997_pmic_id,
+};
+
+static int __init max8997_pmic_init(void)
+{
+	return platform_driver_register(&max8997_pmic_driver);
+}
+subsys_initcall(max8997_pmic_init);
+
+static void __exit max8997_pmic_cleanup(void)
+{
+	platform_driver_unregister(&max8997_pmic_driver);
+}
+module_exit(max8997_pmic_cleanup);
+
+MODULE_DESCRIPTION("MAXIM 8997/8966 Regulator Driver");
+MODULE_AUTHOR("MyungJoo Ham <myungjoo.ham@samsung.com>");
+MODULE_LICENSE("GPL");
diff --git a/drivers/regulator/mc13783-regulator.c b/drivers/regulator/mc13783-regulator.c
index 3e5d0c3..23249cb 100644
--- a/drivers/regulator/mc13783-regulator.c
+++ b/drivers/regulator/mc13783-regulator.c
@@ -15,6 +15,7 @@
 #include <linux/regulator/driver.h>
 #include <linux/platform_device.h>
 #include <linux/kernel.h>
+#include <linux/mfd/core.h>
 #include <linux/slab.h>
 #include <linux/init.h>
 #include <linux/err.h>
@@ -336,8 +337,7 @@
 {
 	struct mc13xxx_regulator_priv *priv;
 	struct mc13xxx *mc13783 = dev_get_drvdata(pdev->dev.parent);
-	struct mc13783_regulator_platform_data *pdata =
-		dev_get_platdata(&pdev->dev);
+	struct mc13783_regulator_platform_data *pdata = mfd_get_data(pdev);
 	struct mc13783_regulator_init_data *init_data;
 	int i, ret;
 
@@ -381,8 +381,7 @@
 static int __devexit mc13783_regulator_remove(struct platform_device *pdev)
 {
 	struct mc13xxx_regulator_priv *priv = platform_get_drvdata(pdev);
-	struct mc13783_regulator_platform_data *pdata =
-		dev_get_platdata(&pdev->dev);
+	struct mc13783_regulator_platform_data *pdata = mfd_get_data(pdev);
 	int i;
 
 	platform_set_drvdata(pdev, NULL);
diff --git a/drivers/regulator/mc13892-regulator.c b/drivers/regulator/mc13892-regulator.c
index 1b8f739..6f15168 100644
--- a/drivers/regulator/mc13892-regulator.c
+++ b/drivers/regulator/mc13892-regulator.c
@@ -15,6 +15,7 @@
 #include <linux/regulator/driver.h>
 #include <linux/platform_device.h>
 #include <linux/kernel.h>
+#include <linux/mfd/core.h>
 #include <linux/slab.h>
 #include <linux/init.h>
 #include <linux/err.h>
@@ -520,8 +521,7 @@
 {
 	struct mc13xxx_regulator_priv *priv;
 	struct mc13xxx *mc13892 = dev_get_drvdata(pdev->dev.parent);
-	struct mc13xxx_regulator_platform_data *pdata =
-		dev_get_platdata(&pdev->dev);
+	struct mc13xxx_regulator_platform_data *pdata = mfd_get_data(pdev);
 	struct mc13xxx_regulator_init_data *init_data;
 	int i, ret;
 	u32 val;
@@ -595,8 +595,7 @@
 static int __devexit mc13892_regulator_remove(struct platform_device *pdev)
 {
 	struct mc13xxx_regulator_priv *priv = platform_get_drvdata(pdev);
-	struct mc13xxx_regulator_platform_data *pdata =
-		dev_get_platdata(&pdev->dev);
+	struct mc13xxx_regulator_platform_data *pdata = mfd_get_data(pdev);
 	int i;
 
 	platform_set_drvdata(pdev, NULL);
diff --git a/drivers/regulator/tps6105x-regulator.c b/drivers/regulator/tps6105x-regulator.c
new file mode 100644
index 0000000..1661499
--- /dev/null
+++ b/drivers/regulator/tps6105x-regulator.c
@@ -0,0 +1,196 @@
+/*
+ * Driver for TPS61050/61052 boost converters, typically used for white LEDs
+ * or audio amplifiers.
+ *
+ * Copyright (C) 2011 ST-Ericsson SA
+ * Written on behalf of Linaro for ST-Ericsson
+ *
+ * Author: Linus Walleij <linus.walleij@linaro.org>
+ *
+ * License terms: GNU General Public License (GPL) version 2
+ */
+
+#include <linux/module.h>
+#include <linux/kernel.h>
+#include <linux/init.h>
+#include <linux/err.h>
+#include <linux/i2c.h>
+#include <linux/platform_device.h>
+#include <linux/regulator/driver.h>
+#include <linux/mfd/core.h>
+#include <linux/mfd/tps6105x.h>
+
+static const int tps6105x_voltages[] = {
+	4500000,
+	5000000,
+	5250000,
+	5000000, /* There is an additional 5V */
+};
+
+static int tps6105x_regulator_enable(struct regulator_dev *rdev)
+{
+	struct tps6105x *tps6105x = rdev_get_drvdata(rdev);
+	int ret;
+
+	/* Activate voltage mode */
+	ret = tps6105x_mask_and_set(tps6105x, TPS6105X_REG_0,
+		TPS6105X_REG0_MODE_MASK,
+		TPS6105X_REG0_MODE_VOLTAGE << TPS6105X_REG0_MODE_SHIFT);
+	if (ret)
+		return ret;
+
+	return 0;
+}
+
+static int tps6105x_regulator_disable(struct regulator_dev *rdev)
+{
+	struct tps6105x *tps6105x = rdev_get_drvdata(rdev);
+	int ret;
+
+	/* Set into shutdown mode */
+	ret = tps6105x_mask_and_set(tps6105x, TPS6105X_REG_0,
+		TPS6105X_REG0_MODE_MASK,
+		TPS6105X_REG0_MODE_SHUTDOWN << TPS6105X_REG0_MODE_SHIFT);
+	if (ret)
+		return ret;
+
+	return 0;
+}
+
+static int tps6105x_regulator_is_enabled(struct regulator_dev *rdev)
+{
+	struct tps6105x *tps6105x = rdev_get_drvdata(rdev);
+	u8 regval;
+	int ret;
+
+	ret = tps6105x_get(tps6105x, TPS6105X_REG_0, &regval);
+	if (ret)
+		return ret;
+	regval &= TPS6105X_REG0_MODE_MASK;
+	regval >>= TPS6105X_REG0_MODE_SHIFT;
+
+	if (regval == TPS6105X_REG0_MODE_VOLTAGE)
+		return 1;
+
+	return 0;
+}
+
+static int tps6105x_regulator_get_voltage_sel(struct regulator_dev *rdev)
+{
+	struct tps6105x *tps6105x = rdev_get_drvdata(rdev);
+	u8 regval;
+	int ret;
+
+	ret = tps6105x_get(tps6105x, TPS6105X_REG_0, &regval);
+	if (ret)
+		return ret;
+
+	regval &= TPS6105X_REG0_VOLTAGE_MASK;
+	regval >>= TPS6105X_REG0_VOLTAGE_SHIFT;
+	return (int) regval;
+}
+
+static int tps6105x_regulator_set_voltage_sel(struct regulator_dev *rdev,
+					      unsigned selector)
+{
+	struct tps6105x *tps6105x = rdev_get_drvdata(rdev);
+	int ret;
+
+	ret = tps6105x_mask_and_set(tps6105x, TPS6105X_REG_0,
+				    TPS6105X_REG0_VOLTAGE_MASK,
+				    selector << TPS6105X_REG0_VOLTAGE_SHIFT);
+	if (ret)
+		return ret;
+
+	return 0;
+}
+
+static int tps6105x_regulator_list_voltage(struct regulator_dev *rdev,
+					   unsigned selector)
+{
+	if (selector >= ARRAY_SIZE(tps6105x_voltages))
+		return -EINVAL;
+
+	return tps6105x_voltages[selector];
+}
+
+static struct regulator_ops tps6105x_regulator_ops = {
+	.enable		= tps6105x_regulator_enable,
+	.disable	= tps6105x_regulator_disable,
+	.is_enabled	= tps6105x_regulator_is_enabled,
+	.get_voltage_sel = tps6105x_regulator_get_voltage_sel,
+	.set_voltage_sel = tps6105x_regulator_set_voltage_sel,
+	.list_voltage	= tps6105x_regulator_list_voltage,
+};
+
+static struct regulator_desc tps6105x_regulator_desc = {
+	.name		= "tps6105x-boost",
+	.ops		= &tps6105x_regulator_ops,
+	.type		= REGULATOR_VOLTAGE,
+	.id		= 0,
+	.owner		= THIS_MODULE,
+	.n_voltages	= ARRAY_SIZE(tps6105x_voltages),
+};
+
+/*
+ * Registers the chip as a voltage regulator
+ */
+static int __devinit tps6105x_regulator_probe(struct platform_device *pdev)
+{
+	struct tps6105x *tps6105x = mfd_get_data(pdev);
+	struct tps6105x_platform_data *pdata = tps6105x->pdata;
+	int ret;
+
+	/* This instance is not set for regulator mode so bail out */
+	if (pdata->mode != TPS6105X_MODE_VOLTAGE) {
+		dev_info(&pdev->dev,
+			 "chip not in voltage mode mode, exit probe \n");
+		return 0;
+	}
+
+	/* Register regulator with framework */
+	tps6105x->regulator = regulator_register(&tps6105x_regulator_desc,
+					     &tps6105x->client->dev,
+					     pdata->regulator_data, tps6105x);
+	if (IS_ERR(tps6105x->regulator)) {
+		ret = PTR_ERR(tps6105x->regulator);
+		dev_err(&tps6105x->client->dev,
+			"failed to register regulator\n");
+		return ret;
+	}
+
+	return 0;
+}
+
+static int __devexit tps6105x_regulator_remove(struct platform_device *pdev)
+{
+	struct tps6105x *tps6105x = platform_get_drvdata(pdev);
+	regulator_unregister(tps6105x->regulator);
+	return 0;
+}
+
+static struct platform_driver tps6105x_regulator_driver = {
+	.driver = {
+		.name  = "tps6105x-regulator",
+		.owner = THIS_MODULE,
+	},
+	.probe = tps6105x_regulator_probe,
+	.remove = __devexit_p(tps6105x_regulator_remove),
+};
+
+static __init int tps6105x_regulator_init(void)
+{
+	return platform_driver_register(&tps6105x_regulator_driver);
+}
+subsys_initcall(tps6105x_regulator_init);
+
+static __exit void tps6105x_regulator_exit(void)
+{
+	platform_driver_unregister(&tps6105x_regulator_driver);
+}
+module_exit(tps6105x_regulator_exit);
+
+MODULE_AUTHOR("Linus Walleij <linus.walleij@linaro.org>");
+MODULE_DESCRIPTION("TPS6105x regulator driver");
+MODULE_LICENSE("GPL v2");
+MODULE_ALIAS("platform:tps6105x-regulator");
diff --git a/drivers/regulator/twl-regulator.c b/drivers/regulator/twl-regulator.c
index bd332cf..6a29285 100644
--- a/drivers/regulator/twl-regulator.c
+++ b/drivers/regulator/twl-regulator.c
@@ -475,6 +475,13 @@
 	.get_status	= twlreg_get_status,
 };
 
+static struct regulator_ops twl6030_fixed_resource = {
+	.enable		= twlreg_enable,
+	.disable	= twlreg_disable,
+	.is_enabled	= twlreg_is_enabled,
+	.get_status	= twlreg_get_status,
+};
+
 /*----------------------------------------------------------------------*/
 
 #define TWL4030_FIXED_LDO(label, offset, mVolts, num, turnon_delay, \
@@ -538,6 +545,20 @@
 		}, \
 	}
 
+#define TWL6030_FIXED_RESOURCE(label, offset, num, turnon_delay, remap_conf) { \
+	.base = offset, \
+	.id = num, \
+	.delay = turnon_delay, \
+	.remap = remap_conf, \
+	.desc = { \
+		.name = #label, \
+		.id = TWL6030_REG_##label, \
+		.ops = &twl6030_fixed_resource, \
+		.type = REGULATOR_VOLTAGE, \
+		.owner = THIS_MODULE, \
+		}, \
+	}
+
 /*
  * We list regulators here if systems need some level of
  * software control over them after boot.
@@ -577,7 +598,8 @@
 	TWL6030_FIXED_LDO(VANA, 0x50, 2100, 15, 0, 0x21),
 	TWL6030_FIXED_LDO(VCXIO, 0x60, 1800, 16, 0, 0x21),
 	TWL6030_FIXED_LDO(VDAC, 0x64, 1800, 17, 0, 0x21),
-	TWL6030_FIXED_LDO(VUSB, 0x70, 3300, 18, 0, 0x21)
+	TWL6030_FIXED_LDO(VUSB, 0x70, 3300, 18, 0, 0x21),
+	TWL6030_FIXED_RESOURCE(CLK32KG, 0x8C, 48, 0, 0x21),
 };
 
 static int __devinit twlreg_probe(struct platform_device *pdev)
diff --git a/drivers/spi/xilinx_spi.c b/drivers/spi/xilinx_spi.c
index 4d2c75d..c69c6f2 100644
--- a/drivers/spi/xilinx_spi.c
+++ b/drivers/spi/xilinx_spi.c
@@ -18,6 +18,7 @@
 #include <linux/interrupt.h>
 #include <linux/of.h>
 #include <linux/platform_device.h>
+#include <linux/mfd/core.h>
 #include <linux/spi/spi.h>
 #include <linux/spi/spi_bitbang.h>
 #include <linux/spi/xilinx_spi.h>
@@ -470,7 +471,7 @@
 	struct spi_master *master;
 	u8 i;
 
-	pdata = dev->dev.platform_data;
+	pdata = mfd_get_data(dev);
 	if (pdata) {
 		num_cs = pdata->num_chipselect;
 		little_endian = pdata->little_endian;
diff --git a/drivers/usb/host/ohci-tmio.c b/drivers/usb/host/ohci-tmio.c
index 8dabe8e..3558491 100644
--- a/drivers/usb/host/ohci-tmio.c
+++ b/drivers/usb/host/ohci-tmio.c
@@ -185,7 +185,7 @@
 
 static int __devinit ohci_hcd_tmio_drv_probe(struct platform_device *dev)
 {
-	struct mfd_cell *cell = dev->dev.platform_data;
+	const struct mfd_cell *cell = mfd_get_cell(dev);
 	struct resource *regs = platform_get_resource(dev, IORESOURCE_MEM, 0);
 	struct resource *config = platform_get_resource(dev, IORESOURCE_MEM, 1);
 	struct resource *sram = platform_get_resource(dev, IORESOURCE_MEM, 2);
@@ -274,7 +274,7 @@
 {
 	struct usb_hcd *hcd = platform_get_drvdata(dev);
 	struct tmio_hcd *tmio = hcd_to_tmio(hcd);
-	struct mfd_cell *cell = dev->dev.platform_data;
+	const struct mfd_cell *cell = mfd_get_cell(dev);
 
 	usb_remove_hcd(hcd);
 	tmio_stop_hc(dev);
@@ -293,7 +293,7 @@
 #ifdef CONFIG_PM
 static int ohci_hcd_tmio_drv_suspend(struct platform_device *dev, pm_message_t state)
 {
-	struct mfd_cell *cell = dev->dev.platform_data;
+	const struct mfd_cell *cell = mfd_get_cell(dev);
 	struct usb_hcd *hcd = platform_get_drvdata(dev);
 	struct ohci_hcd *ohci = hcd_to_ohci(hcd);
 	struct tmio_hcd *tmio = hcd_to_tmio(hcd);
@@ -326,7 +326,7 @@
 
 static int ohci_hcd_tmio_drv_resume(struct platform_device *dev)
 {
-	struct mfd_cell *cell = dev->dev.platform_data;
+	const struct mfd_cell *cell = mfd_get_cell(dev);
 	struct usb_hcd *hcd = platform_get_drvdata(dev);
 	struct ohci_hcd *ohci = hcd_to_ohci(hcd);
 	struct tmio_hcd *tmio = hcd_to_tmio(hcd);
diff --git a/drivers/video/backlight/88pm860x_bl.c b/drivers/video/backlight/88pm860x_bl.c
index e59623a..c8b520e 100644
--- a/drivers/video/backlight/88pm860x_bl.c
+++ b/drivers/video/backlight/88pm860x_bl.c
@@ -12,11 +12,12 @@
 #include <linux/init.h>
 #include <linux/kernel.h>
 #include <linux/platform_device.h>
+#include <linux/slab.h>
 #include <linux/fb.h>
 #include <linux/i2c.h>
 #include <linux/backlight.h>
+#include <linux/mfd/core.h>
 #include <linux/mfd/88pm860x.h>
-#include <linux/slab.h>
 
 #define MAX_BRIGHTNESS		(0xFF)
 #define MIN_BRIGHTNESS		(0)
@@ -161,32 +162,13 @@
 	.get_brightness	= pm860x_backlight_get_brightness,
 };
 
-static int __check_device(struct pm860x_backlight_pdata *pdata, char *name)
-{
-	struct pm860x_backlight_pdata *p = pdata;
-	int ret = -EINVAL;
-
-	while (p && p->id) {
-		if ((p->id != PM8606_ID_BACKLIGHT) || (p->flags < 0))
-			break;
-
-		if (!strncmp(name, pm860x_backlight_name[p->flags],
-			MFD_NAME_SIZE)) {
-			ret = (int)p->flags;
-			break;
-		}
-		p++;
-	}
-	return ret;
-}
-
 static int pm860x_backlight_probe(struct platform_device *pdev)
 {
 	struct pm860x_chip *chip = dev_get_drvdata(pdev->dev.parent);
-	struct pm860x_platform_data *pm860x_pdata;
 	struct pm860x_backlight_pdata *pdata = NULL;
 	struct pm860x_backlight_data *data;
 	struct backlight_device *bl;
+	struct mfd_cell *cell;
 	struct resource *res;
 	struct backlight_properties props;
 	unsigned char value;
@@ -199,10 +181,10 @@
 		return -EINVAL;
 	}
 
-	if (pdev->dev.parent->platform_data) {
-		pm860x_pdata = pdev->dev.parent->platform_data;
-		pdata = pm860x_pdata->backlight;
-	}
+	cell = pdev->dev.platform_data;
+	if (cell == NULL)
+		return -ENODEV;
+	pdata = cell->mfd_data;
 	if (pdata == NULL) {
 		dev_err(&pdev->dev, "platform data isn't assigned to "
 			"backlight\n");
@@ -219,7 +201,7 @@
 	data->current_brightness = MAX_BRIGHTNESS;
 	data->pwm = pdata->pwm;
 	data->iset = pdata->iset;
-	data->port = __check_device(pdata, name);
+	data->port = pdata->flags;
 	if (data->port < 0) {
 		dev_err(&pdev->dev, "wrong platform data is assigned");
 		kfree(data);
diff --git a/drivers/video/tmiofb.c b/drivers/video/tmiofb.c
index dfef88c..9710bf8 100644
--- a/drivers/video/tmiofb.c
+++ b/drivers/video/tmiofb.c
@@ -250,8 +250,7 @@
  */
 static int tmiofb_hw_stop(struct platform_device *dev)
 {
-	struct mfd_cell *cell = dev->dev.platform_data;
-	struct tmio_fb_data *data = cell->driver_data;
+	struct tmio_fb_data *data = mfd_get_data(dev);
 	struct fb_info *info = platform_get_drvdata(dev);
 	struct tmiofb_par *par = info->par;
 
@@ -268,7 +267,7 @@
  */
 static int tmiofb_hw_init(struct platform_device *dev)
 {
-	struct mfd_cell *cell = dev->dev.platform_data;
+	const struct mfd_cell *cell = mfd_get_cell(dev);
 	struct fb_info *info = platform_get_drvdata(dev);
 	struct tmiofb_par *par = info->par;
 	const struct resource *nlcr = &cell->resources[0];
@@ -312,8 +311,7 @@
  */
 static void tmiofb_hw_mode(struct platform_device *dev)
 {
-	struct mfd_cell *cell = dev->dev.platform_data;
-	struct tmio_fb_data *data = cell->driver_data;
+	struct tmio_fb_data *data = mfd_get_data(dev);
 	struct fb_info *info = platform_get_drvdata(dev);
 	struct fb_videomode *mode = info->mode;
 	struct tmiofb_par *par = info->par;
@@ -559,9 +557,8 @@
 static struct fb_videomode *
 tmiofb_find_mode(struct fb_info *info, struct fb_var_screeninfo *var)
 {
-	struct mfd_cell *cell =
-		info->device->platform_data;
-	struct tmio_fb_data *data = cell->driver_data;
+	struct tmio_fb_data *data =
+			mfd_get_data(to_platform_device(info->device));
 	struct fb_videomode *best = NULL;
 	int i;
 
@@ -581,9 +578,8 @@
 {
 
 	struct fb_videomode *mode;
-	struct mfd_cell *cell =
-		info->device->platform_data;
-	struct tmio_fb_data *data = cell->driver_data;
+	struct tmio_fb_data *data =
+			mfd_get_data(to_platform_device(info->device));
 
 	mode = tmiofb_find_mode(info, var);
 	if (!mode || var->bits_per_pixel > 16)
@@ -683,8 +679,8 @@
 
 static int __devinit tmiofb_probe(struct platform_device *dev)
 {
-	struct mfd_cell *cell = dev->dev.platform_data;
-	struct tmio_fb_data *data = cell->driver_data;
+	const struct mfd_cell *cell = mfd_get_cell(dev);
+	struct tmio_fb_data *data = mfd_get_data(dev);
 	struct resource *ccr = platform_get_resource(dev, IORESOURCE_MEM, 1);
 	struct resource *lcr = platform_get_resource(dev, IORESOURCE_MEM, 0);
 	struct resource *vram = platform_get_resource(dev, IORESOURCE_MEM, 2);
@@ -811,7 +807,7 @@
 
 static int __devexit tmiofb_remove(struct platform_device *dev)
 {
-	struct mfd_cell *cell = dev->dev.platform_data;
+	const struct mfd_cell *cell = mfd_get_cell(dev);
 	struct fb_info *info = platform_get_drvdata(dev);
 	int irq = platform_get_irq(dev, 0);
 	struct tmiofb_par *par;
@@ -941,7 +937,7 @@
 #ifdef CONFIG_FB_TMIO_ACCELL
 	struct tmiofb_par *par = info->par;
 #endif
-	struct mfd_cell *cell = dev->dev.platform_data;
+	const struct mfd_cell *cell = mfd_get_cell(dev);
 	int retval = 0;
 
 	console_lock();
@@ -973,7 +969,7 @@
 static int tmiofb_resume(struct platform_device *dev)
 {
 	struct fb_info *info = platform_get_drvdata(dev);
-	struct mfd_cell *cell = dev->dev.platform_data;
+	const struct mfd_cell *cell = mfd_get_cell(dev);
 	int retval = 0;
 
 	console_lock();
diff --git a/drivers/w1/masters/ds1wm.c b/drivers/w1/masters/ds1wm.c
index 6b85e7f..95921b7 100644
--- a/drivers/w1/masters/ds1wm.c
+++ b/drivers/w1/masters/ds1wm.c
@@ -90,7 +90,7 @@
 	void		__iomem *map;
 	int		bus_shift; /* # of shifts to calc register offsets */
 	struct platform_device *pdev;
-	struct mfd_cell	*cell;
+	const struct mfd_cell *cell;
 	int		irq;
 	int		active_high;
 	int		slave_present;
@@ -216,7 +216,7 @@
 static void ds1wm_up(struct ds1wm_data *ds1wm_data)
 {
 	int divisor;
-	struct ds1wm_driver_data *plat = ds1wm_data->cell->driver_data;
+	struct ds1wm_driver_data *plat = mfd_get_data(ds1wm_data->pdev);
 
 	if (ds1wm_data->cell->enable)
 		ds1wm_data->cell->enable(ds1wm_data->pdev);
@@ -330,16 +330,11 @@
 	struct ds1wm_data *ds1wm_data;
 	struct ds1wm_driver_data *plat;
 	struct resource *res;
-	struct mfd_cell *cell;
 	int ret;
 
 	if (!pdev)
 		return -ENODEV;
 
-	cell = pdev->dev.platform_data;
-	if (!cell)
-		return -ENODEV;
-
 	ds1wm_data = kzalloc(sizeof(*ds1wm_data), GFP_KERNEL);
 	if (!ds1wm_data)
 		return -ENOMEM;
@@ -356,13 +351,13 @@
 		ret = -ENOMEM;
 		goto err0;
 	}
-	plat = cell->driver_data;
+	plat = mfd_get_data(pdev);
 
 	/* calculate bus shift from mem resource */
 	ds1wm_data->bus_shift = resource_size(res) >> 3;
 
 	ds1wm_data->pdev = pdev;
-	ds1wm_data->cell = cell;
+	ds1wm_data->cell = mfd_get_cell(pdev);
 
 	res = platform_get_resource(pdev, IORESOURCE_IRQ, 0);
 	if (!res) {
diff --git a/drivers/watchdog/rdc321x_wdt.c b/drivers/watchdog/rdc321x_wdt.c
index 3939e53..d8e7250 100644
--- a/drivers/watchdog/rdc321x_wdt.c
+++ b/drivers/watchdog/rdc321x_wdt.c
@@ -37,6 +37,7 @@
 #include <linux/io.h>
 #include <linux/uaccess.h>
 #include <linux/mfd/rdc321x.h>
+#include <linux/mfd/core.h>
 
 #define RDC_WDT_MASK	0x80000000 /* Mask */
 #define RDC_WDT_EN	0x00800000 /* Enable bit */
@@ -231,7 +232,7 @@
 	struct resource *r;
 	struct rdc321x_wdt_pdata *pdata;
 
-	pdata = platform_get_drvdata(pdev);
+	pdata = mfd_get_data(pdev);
 	if (!pdata) {
 		dev_err(&pdev->dev, "no platform data supplied\n");
 		return -ENODEV;
diff --git a/include/linux/i2c/twl.h b/include/linux/i2c/twl.h
index 58afd9d..0c0d1ae 100644
--- a/include/linux/i2c/twl.h
+++ b/include/linux/i2c/twl.h
@@ -698,6 +698,7 @@
 	struct regulator_init_data              *vana;
 	struct regulator_init_data              *vcxio;
 	struct regulator_init_data              *vusb;
+	struct regulator_init_data		*clk32kg;
 };
 
 /*----------------------------------------------------------------------*/
@@ -777,5 +778,6 @@
 
 /* INTERNAL LDOs */
 #define TWL6030_REG_VRTC	47
+#define TWL6030_REG_CLK32KG	48
 
 #endif /* End of __TWL4030_H */
diff --git a/include/linux/i2c/twl4030-madc.h b/include/linux/i2c/twl4030-madc.h
new file mode 100644
index 0000000..6427d29
--- /dev/null
+++ b/include/linux/i2c/twl4030-madc.h
@@ -0,0 +1,141 @@
+/*
+ * twl4030_madc.h - Header for TWL4030 MADC
+ *
+ * Copyright (C) 2011 Texas Instruments Incorporated - http://www.ti.com/
+ * J Keerthy <j-keerthy@ti.com>
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License
+ * version 2 as published by the Free Software Foundation.
+ *
+ * This program is distributed in the hope that it will be useful, but
+ * WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the GNU
+ * General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA
+ * 02110-1301 USA
+ *
+ */
+
+#ifndef _TWL4030_MADC_H
+#define _TWL4030_MADC_H
+
+struct twl4030_madc_conversion_method {
+	u8 sel;
+	u8 avg;
+	u8 rbase;
+	u8 ctrl;
+};
+
+#define TWL4030_MADC_MAX_CHANNELS 16
+
+
+/*
+ * twl4030_madc_request- madc request packet for channel conversion
+ * @channels:	16 bit bitmap for individual channels
+ * @do_avgP:	sample the input channel for 4 consecutive cycles
+ * @method:	RT, SW1, SW2
+ * @type:	Polling or interrupt based method
+ */
+
+struct twl4030_madc_request {
+	unsigned long channels;
+	u16 do_avg;
+	u16 method;
+	u16 type;
+	bool active;
+	bool result_pending;
+	int rbuf[TWL4030_MADC_MAX_CHANNELS];
+	void (*func_cb)(int len, int channels, int *buf);
+};
+
+enum conversion_methods {
+	TWL4030_MADC_RT,
+	TWL4030_MADC_SW1,
+	TWL4030_MADC_SW2,
+	TWL4030_MADC_NUM_METHODS
+};
+
+enum sample_type {
+	TWL4030_MADC_WAIT,
+	TWL4030_MADC_IRQ_ONESHOT,
+	TWL4030_MADC_IRQ_REARM
+};
+
+#define TWL4030_MADC_CTRL1		0x00
+#define TWL4030_MADC_CTRL2		0x01
+
+#define TWL4030_MADC_RTSELECT_LSB	0x02
+#define TWL4030_MADC_SW1SELECT_LSB	0x06
+#define TWL4030_MADC_SW2SELECT_LSB	0x0A
+
+#define TWL4030_MADC_RTAVERAGE_LSB	0x04
+#define TWL4030_MADC_SW1AVERAGE_LSB	0x08
+#define TWL4030_MADC_SW2AVERAGE_LSB	0x0C
+
+#define TWL4030_MADC_CTRL_SW1		0x12
+#define TWL4030_MADC_CTRL_SW2		0x13
+
+#define TWL4030_MADC_RTCH0_LSB		0x17
+#define TWL4030_MADC_GPCH0_LSB		0x37
+
+#define TWL4030_MADC_MADCON	(1 << 0)	/* MADC power on */
+#define TWL4030_MADC_BUSY	(1 << 0)	/* MADC busy */
+/* MADC conversion completion */
+#define TWL4030_MADC_EOC_SW	(1 << 1)
+/* MADC SWx start conversion */
+#define TWL4030_MADC_SW_START	(1 << 5)
+#define TWL4030_MADC_ADCIN0	(1 << 0)
+#define TWL4030_MADC_ADCIN1	(1 << 1)
+#define TWL4030_MADC_ADCIN2	(1 << 2)
+#define TWL4030_MADC_ADCIN3	(1 << 3)
+#define TWL4030_MADC_ADCIN4	(1 << 4)
+#define TWL4030_MADC_ADCIN5	(1 << 5)
+#define TWL4030_MADC_ADCIN6	(1 << 6)
+#define TWL4030_MADC_ADCIN7	(1 << 7)
+#define TWL4030_MADC_ADCIN8	(1 << 8)
+#define TWL4030_MADC_ADCIN9	(1 << 9)
+#define TWL4030_MADC_ADCIN10	(1 << 10)
+#define TWL4030_MADC_ADCIN11	(1 << 11)
+#define TWL4030_MADC_ADCIN12	(1 << 12)
+#define TWL4030_MADC_ADCIN13	(1 << 13)
+#define TWL4030_MADC_ADCIN14	(1 << 14)
+#define TWL4030_MADC_ADCIN15	(1 << 15)
+
+/* Fixed channels */
+#define TWL4030_MADC_BTEMP	TWL4030_MADC_ADCIN1
+#define TWL4030_MADC_VBUS	TWL4030_MADC_ADCIN8
+#define TWL4030_MADC_VBKB	TWL4030_MADC_ADCIN9
+#define TWL4030_MADC_ICHG	TWL4030_MADC_ADCIN10
+#define TWL4030_MADC_VCHG	TWL4030_MADC_ADCIN11
+#define TWL4030_MADC_VBAT	TWL4030_MADC_ADCIN12
+
+/* Step size and prescaler ratio */
+#define TEMP_STEP_SIZE          147
+#define TEMP_PSR_R              100
+#define CURR_STEP_SIZE		147
+#define CURR_PSR_R1		44
+#define CURR_PSR_R2		88
+
+#define TWL4030_BCI_BCICTL1	0x23
+#define TWL4030_BCI_CGAIN	0x020
+#define TWL4030_BCI_MESBAT	(1 << 1)
+#define TWL4030_BCI_TYPEN	(1 << 4)
+#define TWL4030_BCI_ITHEN	(1 << 3)
+
+#define REG_BCICTL2             0x024
+#define TWL4030_BCI_ITHSENS	0x007
+
+struct twl4030_madc_user_parms {
+	int channel;
+	int average;
+	int status;
+	u16 result;
+};
+
+int twl4030_madc_conversion(struct twl4030_madc_request *conv);
+int twl4030_get_madc_conversion(int channel_no);
+#endif
diff --git a/include/linux/mfd/88pm860x.h b/include/linux/mfd/88pm860x.h
index 4db1fbd..8fba797 100644
--- a/include/linux/mfd/88pm860x.h
+++ b/include/linux/mfd/88pm860x.h
@@ -131,9 +131,11 @@
 	PM8607_ID_LDO8,
 	PM8607_ID_LDO9,
 	PM8607_ID_LDO10,
+	PM8607_ID_LDO11,
 	PM8607_ID_LDO12,
 	PM8607_ID_LDO13,
 	PM8607_ID_LDO14,
+	PM8607_ID_LDO15,
 
 	PM8607_ID_RG_MAX,
 };
@@ -310,8 +312,6 @@
 
 };
 
-#define PM8607_MAX_REGULATOR	PM8607_ID_RG_MAX	/* 3 Bucks, 13 LDOs */
-
 enum {
 	GI2C_PORT = 0,
 	PI2C_PORT,
@@ -351,23 +351,31 @@
 	struct pm860x_led_pdata		*led;
 	struct pm860x_touch_pdata	*touch;
 	struct pm860x_power_pdata	*power;
+	struct regulator_init_data	*regulator;
 
 	unsigned short	companion_addr;	/* I2C address of companion chip */
 	int		i2c_port;	/* Controlled by GI2C or PI2C */
 	int		irq_mode;	/* Clear interrupt by read/write(0/1) */
 	int		irq_base;	/* IRQ base number of 88pm860x */
-	struct regulator_init_data *regulator[PM8607_MAX_REGULATOR];
+	int		num_leds;
+	int		num_backlights;
+	int		num_regulators;
 };
 
-extern char pm860x_backlight_name[][MFD_NAME_SIZE];
-extern char pm860x_led_name[][MFD_NAME_SIZE];
-
 extern int pm860x_reg_read(struct i2c_client *, int);
 extern int pm860x_reg_write(struct i2c_client *, int, unsigned char);
 extern int pm860x_bulk_read(struct i2c_client *, int, int, unsigned char *);
 extern int pm860x_bulk_write(struct i2c_client *, int, int, unsigned char *);
 extern int pm860x_set_bits(struct i2c_client *, int, unsigned char,
 			   unsigned char);
+extern int pm860x_page_reg_read(struct i2c_client *, int);
+extern int pm860x_page_reg_write(struct i2c_client *, int, unsigned char);
+extern int pm860x_page_bulk_read(struct i2c_client *, int, int,
+				 unsigned char *);
+extern int pm860x_page_bulk_write(struct i2c_client *, int, int,
+				  unsigned char *);
+extern int pm860x_page_set_bits(struct i2c_client *, int, unsigned char,
+				unsigned char);
 
 extern int pm860x_device_init(struct pm860x_chip *chip,
 			      struct pm860x_platform_data *pdata) __devinit ;
diff --git a/include/linux/mfd/ab8500.h b/include/linux/mfd/ab8500.h
index 37f56b7..56f8dea 100644
--- a/include/linux/mfd/ab8500.h
+++ b/include/linux/mfd/ab8500.h
@@ -111,8 +111,8 @@
  * @dev: parent device
  * @lock: read/write operations lock
  * @irq_lock: genirq bus lock
- * @revision: chip revision
  * @irq: irq line
+ * @chip_id: chip revision id
  * @write: register write
  * @read: register read
  * @rx_buf: rx buf for SPI
@@ -124,7 +124,7 @@
 	struct device	*dev;
 	struct mutex	lock;
 	struct mutex	irq_lock;
-	int		revision;
+
 	int		irq_base;
 	int		irq;
 	u8		chip_id;
diff --git a/include/linux/mfd/ab8500/gpadc.h b/include/linux/mfd/ab8500/gpadc.h
new file mode 100644
index 0000000..46b9540
--- /dev/null
+++ b/include/linux/mfd/ab8500/gpadc.h
@@ -0,0 +1,32 @@
+/*
+ * Copyright (C) 2010 ST-Ericsson SA
+ * Licensed under GPLv2.
+ *
+ * Author: Arun R Murthy <arun.murthy@stericsson.com>
+ * Author: Daniel Willerud <daniel.willerud@stericsson.com>
+ */
+
+#ifndef	_AB8500_GPADC_H
+#define _AB8500_GPADC_H
+
+/* GPADC source: From datasheet(ADCSwSel[4:0] in GPADCCtrl2) */
+#define BAT_CTRL	0x01
+#define BTEMP_BALL	0x02
+#define MAIN_CHARGER_V	0x03
+#define ACC_DETECT1	0x04
+#define ACC_DETECT2	0x05
+#define ADC_AUX1	0x06
+#define ADC_AUX2	0x07
+#define MAIN_BAT_V	0x08
+#define VBUS_V		0x09
+#define MAIN_CHARGER_C	0x0A
+#define USB_CHARGER_C	0x0B
+#define BK_BAT_V	0x0C
+#define DIE_TEMP	0x0D
+
+struct ab8500_gpadc;
+
+struct ab8500_gpadc *ab8500_gpadc_get(char *name);
+int ab8500_gpadc_convert(struct ab8500_gpadc *gpadc, u8 input);
+
+#endif /* _AB8500_GPADC_H */
diff --git a/include/linux/mfd/ab8500/sysctrl.h b/include/linux/mfd/ab8500/sysctrl.h
new file mode 100644
index 0000000..10da029
--- /dev/null
+++ b/include/linux/mfd/ab8500/sysctrl.h
@@ -0,0 +1,254 @@
+/*
+ * Copyright (C) ST-Ericsson SA 2010
+ * Author: Mattias Nilsson <mattias.i.nilsson@stericsson.com> for ST Ericsson.
+ * License terms: GNU General Public License (GPL) version 2
+ */
+#ifndef __AB8500_SYSCTRL_H
+#define __AB8500_SYSCTRL_H
+
+#include <linux/bitops.h>
+
+#ifdef CONFIG_AB8500_CORE
+
+int ab8500_sysctrl_read(u16 reg, u8 *value);
+int ab8500_sysctrl_write(u16 reg, u8 mask, u8 value);
+
+#else
+
+static inline int ab8500_sysctrl_read(u16 reg, u8 *value)
+{
+	return 0;
+}
+
+static inline int ab8500_sysctrl_write(u16 reg, u8 mask, u8 value)
+{
+	return 0;
+}
+
+#endif /* CONFIG_AB8500_CORE */
+
+static inline int ab8500_sysctrl_set(u16 reg, u8 bits)
+{
+	return ab8500_sysctrl_write(reg, bits, bits);
+}
+
+static inline int ab8500_sysctrl_clear(u16 reg, u8 bits)
+{
+	return ab8500_sysctrl_write(reg, bits, 0);
+}
+
+/* Registers */
+#define AB8500_TURNONSTATUS		0x100
+#define AB8500_RESETSTATUS		0x101
+#define AB8500_PONKEY1PRESSSTATUS	0x102
+#define AB8500_SYSCLKREQSTATUS		0x142
+#define AB8500_STW4500CTRL1		0x180
+#define AB8500_STW4500CTRL2		0x181
+#define AB8500_STW4500CTRL3		0x200
+#define AB8500_MAINWDOGCTRL		0x201
+#define AB8500_MAINWDOGTIMER		0x202
+#define AB8500_LOWBAT			0x203
+#define AB8500_BATTOK			0x204
+#define AB8500_SYSCLKTIMER		0x205
+#define AB8500_SMPSCLKCTRL		0x206
+#define AB8500_SMPSCLKSEL1		0x207
+#define AB8500_SMPSCLKSEL2		0x208
+#define AB8500_SMPSCLKSEL3		0x209
+#define AB8500_SYSULPCLKCONF		0x20A
+#define AB8500_SYSULPCLKCTRL1		0x20B
+#define AB8500_SYSCLKCTRL		0x20C
+#define AB8500_SYSCLKREQ1VALID		0x20D
+#define AB8500_SYSTEMCTRLSUP		0x20F
+#define AB8500_SYSCLKREQ1RFCLKBUF	0x210
+#define AB8500_SYSCLKREQ2RFCLKBUF	0x211
+#define AB8500_SYSCLKREQ3RFCLKBUF	0x212
+#define AB8500_SYSCLKREQ4RFCLKBUF	0x213
+#define AB8500_SYSCLKREQ5RFCLKBUF	0x214
+#define AB8500_SYSCLKREQ6RFCLKBUF	0x215
+#define AB8500_SYSCLKREQ7RFCLKBUF	0x216
+#define AB8500_SYSCLKREQ8RFCLKBUF	0x217
+#define AB8500_DITHERCLKCTRL		0x220
+#define AB8500_SWATCTRL			0x230
+#define AB8500_HIQCLKCTRL		0x232
+#define AB8500_VSIMSYSCLKCTRL		0x233
+
+/* Bits */
+#define AB8500_TURNONSTATUS_PORNVBAT BIT(0)
+#define AB8500_TURNONSTATUS_PONKEY1DBF BIT(1)
+#define AB8500_TURNONSTATUS_PONKEY2DBF BIT(2)
+#define AB8500_TURNONSTATUS_RTCALARM BIT(3)
+#define AB8500_TURNONSTATUS_MAINCHDET BIT(4)
+#define AB8500_TURNONSTATUS_VBUSDET BIT(5)
+#define AB8500_TURNONSTATUS_USBIDDETECT BIT(6)
+
+#define AB8500_RESETSTATUS_RESETN4500NSTATUS BIT(0)
+#define AB8500_RESETSTATUS_SWRESETN4500NSTATUS BIT(2)
+
+#define AB8500_PONKEY1PRESSSTATUS_PONKEY1PRESSTIME_MASK 0x7F
+#define AB8500_PONKEY1PRESSSTATUS_PONKEY1PRESSTIME_SHIFT 0
+
+#define AB8500_SYSCLKREQSTATUS_SYSCLKREQ1STATUS BIT(0)
+#define AB8500_SYSCLKREQSTATUS_SYSCLKREQ2STATUS BIT(1)
+#define AB8500_SYSCLKREQSTATUS_SYSCLKREQ3STATUS BIT(2)
+#define AB8500_SYSCLKREQSTATUS_SYSCLKREQ4STATUS BIT(3)
+#define AB8500_SYSCLKREQSTATUS_SYSCLKREQ5STATUS BIT(4)
+#define AB8500_SYSCLKREQSTATUS_SYSCLKREQ6STATUS BIT(5)
+#define AB8500_SYSCLKREQSTATUS_SYSCLKREQ7STATUS BIT(6)
+#define AB8500_SYSCLKREQSTATUS_SYSCLKREQ8STATUS BIT(7)
+
+#define AB8500_STW4500CTRL1_SWOFF BIT(0)
+#define AB8500_STW4500CTRL1_SWRESET4500N BIT(1)
+#define AB8500_STW4500CTRL1_THDB8500SWOFF BIT(2)
+
+#define AB8500_STW4500CTRL2_RESETNVAUX1VALID BIT(0)
+#define AB8500_STW4500CTRL2_RESETNVAUX2VALID BIT(1)
+#define AB8500_STW4500CTRL2_RESETNVAUX3VALID BIT(2)
+#define AB8500_STW4500CTRL2_RESETNVMODVALID BIT(3)
+#define AB8500_STW4500CTRL2_RESETNVEXTSUPPLY1VALID BIT(4)
+#define AB8500_STW4500CTRL2_RESETNVEXTSUPPLY2VALID BIT(5)
+#define AB8500_STW4500CTRL2_RESETNVEXTSUPPLY3VALID BIT(6)
+#define AB8500_STW4500CTRL2_RESETNVSMPS1VALID BIT(7)
+
+#define AB8500_STW4500CTRL3_CLK32KOUT2DIS BIT(0)
+#define AB8500_STW4500CTRL3_RESETAUDN BIT(1)
+#define AB8500_STW4500CTRL3_RESETDENCN BIT(2)
+#define AB8500_STW4500CTRL3_THSDENA BIT(3)
+
+#define AB8500_MAINWDOGCTRL_MAINWDOGENA BIT(0)
+#define AB8500_MAINWDOGCTRL_MAINWDOGKICK BIT(1)
+#define AB8500_MAINWDOGCTRL_WDEXPTURNONVALID BIT(4)
+
+#define AB8500_MAINWDOGTIMER_MAINWDOGTIMER_MASK 0x7F
+#define AB8500_MAINWDOGTIMER_MAINWDOGTIMER_SHIFT 0
+
+#define AB8500_LOWBAT_LOWBATENA BIT(0)
+#define AB8500_LOWBAT_LOWBAT_MASK 0x7E
+#define AB8500_LOWBAT_LOWBAT_SHIFT 1
+
+#define AB8500_BATTOK_BATTOKSEL0THF_MASK 0x0F
+#define AB8500_BATTOK_BATTOKSEL0THF_SHIFT 0
+#define AB8500_BATTOK_BATTOKSEL1THF_MASK 0xF0
+#define AB8500_BATTOK_BATTOKSEL1THF_SHIFT 4
+
+#define AB8500_SYSCLKTIMER_SYSCLKTIMER_MASK 0x0F
+#define AB8500_SYSCLKTIMER_SYSCLKTIMER_SHIFT 0
+#define AB8500_SYSCLKTIMER_SYSCLKTIMERADJ_MASK 0xF0
+#define AB8500_SYSCLKTIMER_SYSCLKTIMERADJ_SHIFT 4
+
+#define AB8500_SMPSCLKCTRL_SMPSCLKINTSEL_MASK 0x03
+#define AB8500_SMPSCLKCTRL_SMPSCLKINTSEL_SHIFT 0
+#define AB8500_SMPSCLKCTRL_3M2CLKINTENA BIT(2)
+
+#define AB8500_SMPSCLKSEL1_VARMCLKSEL_MASK 0x07
+#define AB8500_SMPSCLKSEL1_VARMCLKSEL_SHIFT 0
+#define AB8500_SMPSCLKSEL1_VAPECLKSEL_MASK 0x38
+#define AB8500_SMPSCLKSEL1_VAPECLKSEL_SHIFT 3
+
+#define AB8500_SMPSCLKSEL2_VMODCLKSEL_MASK 0x07
+#define AB8500_SMPSCLKSEL2_VMODCLKSEL_SHIFT 0
+#define AB8500_SMPSCLKSEL2_VSMPS1CLKSEL_MASK 0x38
+#define AB8500_SMPSCLKSEL2_VSMPS1CLKSEL_SHIFT 3
+
+#define AB8500_SMPSCLKSEL3_VSMPS2CLKSEL_MASK 0x07
+#define AB8500_SMPSCLKSEL3_VSMPS2CLKSEL_SHIFT 0
+#define AB8500_SMPSCLKSEL3_VSMPS3CLKSEL_MASK 0x38
+#define AB8500_SMPSCLKSEL3_VSMPS3CLKSEL_SHIFT 3
+
+#define AB8500_SYSULPCLKCONF_ULPCLKCONF_MASK 0x03
+#define AB8500_SYSULPCLKCONF_ULPCLKCONF_SHIFT 0
+#define AB8500_SYSULPCLKCONF_CLK27MHZSTRE BIT(2)
+#define AB8500_SYSULPCLKCONF_TVOUTCLKDELN BIT(3)
+#define AB8500_SYSULPCLKCONF_TVOUTCLKINV BIT(4)
+#define AB8500_SYSULPCLKCONF_ULPCLKSTRE BIT(5)
+#define AB8500_SYSULPCLKCONF_CLK27MHZBUFENA BIT(6)
+#define AB8500_SYSULPCLKCONF_CLK27MHZPDENA BIT(7)
+
+#define AB8500_SYSULPCLKCTRL1_SYSULPCLKINTSEL_MASK 0x03
+#define AB8500_SYSULPCLKCTRL1_SYSULPCLKINTSEL_SHIFT 0
+#define AB8500_SYSULPCLKCTRL1_ULPCLKREQ BIT(2)
+#define AB8500_SYSULPCLKCTRL1_4500SYSCLKREQ BIT(3)
+#define AB8500_SYSULPCLKCTRL1_AUDIOCLKENA BIT(4)
+#define AB8500_SYSULPCLKCTRL1_SYSCLKBUF2REQ BIT(5)
+#define AB8500_SYSULPCLKCTRL1_SYSCLKBUF3REQ BIT(6)
+#define AB8500_SYSULPCLKCTRL1_SYSCLKBUF4REQ BIT(7)
+
+#define AB8500_SYSCLKCTRL_TVOUTPLLENA BIT(0)
+#define AB8500_SYSCLKCTRL_TVOUTCLKENA BIT(1)
+#define AB8500_SYSCLKCTRL_USBCLKENA BIT(2)
+
+#define AB8500_SYSCLKREQ1VALID_SYSCLKREQ1VALID BIT(0)
+#define AB8500_SYSCLKREQ1VALID_ULPCLKREQ1VALID BIT(1)
+#define AB8500_SYSCLKREQ1VALID_USBSYSCLKREQ1VALID BIT(2)
+
+#define AB8500_SYSTEMCTRLSUP_EXTSUP12LPNCLKSEL_MASK 0x03
+#define AB8500_SYSTEMCTRLSUP_EXTSUP12LPNCLKSEL_SHIFT 0
+#define AB8500_SYSTEMCTRLSUP_EXTSUP3LPNCLKSEL_MASK 0x0C
+#define AB8500_SYSTEMCTRLSUP_EXTSUP3LPNCLKSEL_SHIFT 2
+#define AB8500_SYSTEMCTRLSUP_INTDB8500NOD BIT(4)
+
+#define AB8500_SYSCLKREQ1RFCLKBUF_SYSCLKREQ1RFCLKBUF2 BIT(2)
+#define AB8500_SYSCLKREQ1RFCLKBUF_SYSCLKREQ1RFCLKBUF3 BIT(3)
+#define AB8500_SYSCLKREQ1RFCLKBUF_SYSCLKREQ1RFCLKBUF4 BIT(4)
+
+#define AB8500_SYSCLKREQ2RFCLKBUF_SYSCLKREQ2RFCLKBUF2 BIT(2)
+#define AB8500_SYSCLKREQ2RFCLKBUF_SYSCLKREQ2RFCLKBUF3 BIT(3)
+#define AB8500_SYSCLKREQ2RFCLKBUF_SYSCLKREQ2RFCLKBUF4 BIT(4)
+
+#define AB8500_SYSCLKREQ3RFCLKBUF_SYSCLKREQ3RFCLKBUF2 BIT(2)
+#define AB8500_SYSCLKREQ3RFCLKBUF_SYSCLKREQ3RFCLKBUF3 BIT(3)
+#define AB8500_SYSCLKREQ3RFCLKBUF_SYSCLKREQ3RFCLKBUF4 BIT(4)
+
+#define AB8500_SYSCLKREQ4RFCLKBUF_SYSCLKREQ4RFCLKBUF2 BIT(2)
+#define AB8500_SYSCLKREQ4RFCLKBUF_SYSCLKREQ4RFCLKBUF3 BIT(3)
+#define AB8500_SYSCLKREQ4RFCLKBUF_SYSCLKREQ4RFCLKBUF4 BIT(4)
+
+#define AB8500_SYSCLKREQ5RFCLKBUF_SYSCLKREQ5RFCLKBUF2 BIT(2)
+#define AB8500_SYSCLKREQ5RFCLKBUF_SYSCLKREQ5RFCLKBUF3 BIT(3)
+#define AB8500_SYSCLKREQ5RFCLKBUF_SYSCLKREQ5RFCLKBUF4 BIT(4)
+
+#define AB8500_SYSCLKREQ6RFCLKBUF_SYSCLKREQ6RFCLKBUF2 BIT(2)
+#define AB8500_SYSCLKREQ6RFCLKBUF_SYSCLKREQ6RFCLKBUF3 BIT(3)
+#define AB8500_SYSCLKREQ6RFCLKBUF_SYSCLKREQ6RFCLKBUF4 BIT(4)
+
+#define AB8500_SYSCLKREQ7RFCLKBUF_SYSCLKREQ7RFCLKBUF2 BIT(2)
+#define AB8500_SYSCLKREQ7RFCLKBUF_SYSCLKREQ7RFCLKBUF3 BIT(3)
+#define AB8500_SYSCLKREQ7RFCLKBUF_SYSCLKREQ7RFCLKBUF4 BIT(4)
+
+#define AB8500_SYSCLKREQ8RFCLKBUF_SYSCLKREQ8RFCLKBUF2 BIT(2)
+#define AB8500_SYSCLKREQ8RFCLKBUF_SYSCLKREQ8RFCLKBUF3 BIT(3)
+#define AB8500_SYSCLKREQ8RFCLKBUF_SYSCLKREQ8RFCLKBUF4 BIT(4)
+
+#define AB8500_DITHERCLKCTRL_VARMDITHERENA BIT(0)
+#define AB8500_DITHERCLKCTRL_VSMPS3DITHERENA BIT(1)
+#define AB8500_DITHERCLKCTRL_VSMPS1DITHERENA BIT(2)
+#define AB8500_DITHERCLKCTRL_VSMPS2DITHERENA BIT(3)
+#define AB8500_DITHERCLKCTRL_VMODDITHERENA BIT(4)
+#define AB8500_DITHERCLKCTRL_VAPEDITHERENA BIT(5)
+#define AB8500_DITHERCLKCTRL_DITHERDEL_MASK 0xC0
+#define AB8500_DITHERCLKCTRL_DITHERDEL_SHIFT 6
+
+#define AB8500_SWATCTRL_UPDATERF BIT(0)
+#define AB8500_SWATCTRL_SWATENABLE BIT(1)
+#define AB8500_SWATCTRL_RFOFFTIMER_MASK 0x1C
+#define AB8500_SWATCTRL_RFOFFTIMER_SHIFT 2
+#define AB8500_SWATCTRL_SWATBIT5 BIT(6)
+
+#define AB8500_HIQCLKCTRL_SYSCLKREQ1HIQENAVALID BIT(0)
+#define AB8500_HIQCLKCTRL_SYSCLKREQ2HIQENAVALID BIT(1)
+#define AB8500_HIQCLKCTRL_SYSCLKREQ3HIQENAVALID BIT(2)
+#define AB8500_HIQCLKCTRL_SYSCLKREQ4HIQENAVALID BIT(3)
+#define AB8500_HIQCLKCTRL_SYSCLKREQ5HIQENAVALID BIT(4)
+#define AB8500_HIQCLKCTRL_SYSCLKREQ6HIQENAVALID BIT(5)
+#define AB8500_HIQCLKCTRL_SYSCLKREQ7HIQENAVALID BIT(6)
+#define AB8500_HIQCLKCTRL_SYSCLKREQ8HIQENAVALID BIT(7)
+
+#define AB8500_VSIMSYSCLKCTRL_VSIMSYSCLKREQ1VALID BIT(0)
+#define AB8500_VSIMSYSCLKCTRL_VSIMSYSCLKREQ2VALID BIT(1)
+#define AB8500_VSIMSYSCLKCTRL_VSIMSYSCLKREQ3VALID BIT(2)
+#define AB8500_VSIMSYSCLKCTRL_VSIMSYSCLKREQ4VALID BIT(3)
+#define AB8500_VSIMSYSCLKCTRL_VSIMSYSCLKREQ5VALID BIT(4)
+#define AB8500_VSIMSYSCLKCTRL_VSIMSYSCLKREQ6VALID BIT(5)
+#define AB8500_VSIMSYSCLKCTRL_VSIMSYSCLKREQ7VALID BIT(6)
+#define AB8500_VSIMSYSCLKCTRL_VSIMSYSCLKREQ8VALID BIT(7)
+
+#endif /* __AB8500_SYSCTRL_H */
diff --git a/include/linux/mfd/abx500.h b/include/linux/mfd/abx500.h
index 67bd6f7..7d9b6ae 100644
--- a/include/linux/mfd/abx500.h
+++ b/include/linux/mfd/abx500.h
@@ -186,7 +186,6 @@
 struct ab3550_platform_data {
 	struct {unsigned int base; unsigned int count; } irq;
 	void *dev_data[AB3550_NUM_DEVICES];
-	size_t dev_data_sz[AB3550_NUM_DEVICES];
 	struct abx500_init_settings *init_settings;
 	unsigned int init_settings_sz;
 };
diff --git a/include/linux/mfd/core.h b/include/linux/mfd/core.h
index 835996e..1408bf8 100644
--- a/include/linux/mfd/core.h
+++ b/include/linux/mfd/core.h
@@ -25,22 +25,20 @@
 	const char		*name;
 	int			id;
 
+	/* refcounting for multiple drivers to use a single cell */
+	atomic_t		*usage_count;
 	int			(*enable)(struct platform_device *dev);
 	int			(*disable)(struct platform_device *dev);
+
 	int			(*suspend)(struct platform_device *dev);
 	int			(*resume)(struct platform_device *dev);
 
-	/* driver-specific data for MFD-aware "cell" drivers */
-	void			*driver_data;
-
-	/* platform_data can be used to either pass data to "generic"
-	   driver or as a hook to mfd_cell for the "cell" drivers */
-	void			*platform_data;
-	size_t			data_size;
+	/* mfd_data can be used to pass data to client drivers */
+	void			*mfd_data;
 
 	/*
-	 * This resources can be specified relatively to the parent device.
-	 * For accessing device you should use resources from device
+	 * These resources can be specified relative to the parent device.
+	 * For accessing hardware you should use resources from the platform dev
 	 */
 	int			num_resources;
 	const struct resource	*resources;
@@ -55,11 +53,47 @@
 	bool			pm_runtime_no_callbacks;
 };
 
+/*
+ * Convenience functions for clients using shared cells.  Refcounting
+ * happens automatically, with the cell's enable/disable callbacks
+ * being called only when a device is first being enabled or no other
+ * clients are making use of it.
+ */
+extern int mfd_cell_enable(struct platform_device *pdev);
+extern int mfd_cell_disable(struct platform_device *pdev);
+
+/*
+ * Given a platform device that's been created by mfd_add_devices(), fetch
+ * the mfd_cell that created it.
+ */
+static inline const struct mfd_cell *mfd_get_cell(struct platform_device *pdev)
+{
+	return pdev->dev.platform_data;
+}
+
+/*
+ * Given a platform device that's been created by mfd_add_devices(), fetch
+ * the .mfd_data entry from the mfd_cell that created it.
+ */
+static inline void *mfd_get_data(struct platform_device *pdev)
+{
+	return mfd_get_cell(pdev)->mfd_data;
+}
+
 extern int mfd_add_devices(struct device *parent, int id,
-			   const struct mfd_cell *cells, int n_devs,
+			   struct mfd_cell *cells, int n_devs,
 			   struct resource *mem_base,
 			   int irq_base);
 
 extern void mfd_remove_devices(struct device *parent);
 
+/*
+ * For MFD drivers with clients sharing access to resources, these create
+ * multiple platform devices per cell.  Contention handling must still be
+ * handled via drivers (ie, with enable/disable hooks).
+ */
+extern int mfd_shared_platform_driver_register(struct platform_driver *drv,
+		const char *cellname);
+extern void mfd_shared_platform_driver_unregister(struct platform_driver *drv);
+
 #endif
diff --git a/include/linux/mfd/max8997-private.h b/include/linux/mfd/max8997-private.h
new file mode 100644
index 0000000..93a9477
--- /dev/null
+++ b/include/linux/mfd/max8997-private.h
@@ -0,0 +1,347 @@
+/*
+ * max8997.h - Voltage regulator driver for the Maxim 8997
+ *
+ *  Copyright (C) 2010 Samsung Electrnoics
+ *  MyungJoo Ham <myungjoo.ham@samsung.com>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA  02111-1307  USA
+ */
+
+#ifndef __LINUX_MFD_MAX8997_PRIV_H
+#define __LINUX_MFD_MAX8997_PRIV_H
+
+#include <linux/i2c.h>
+
+enum max8997_pmic_reg {
+	MAX8997_REG_PMIC_ID0	= 0x00,
+	MAX8997_REG_PMIC_ID1	= 0x01,
+	MAX8997_REG_INTSRC	= 0x02,
+	MAX8997_REG_INT1	= 0x03,
+	MAX8997_REG_INT2	= 0x04,
+	MAX8997_REG_INT3	= 0x05,
+	MAX8997_REG_INT4	= 0x06,
+
+	MAX8997_REG_INT1MSK	= 0x08,
+	MAX8997_REG_INT2MSK	= 0x09,
+	MAX8997_REG_INT3MSK	= 0x0a,
+	MAX8997_REG_INT4MSK	= 0x0b,
+
+	MAX8997_REG_STATUS1	= 0x0d,
+	MAX8997_REG_STATUS2	= 0x0e,
+	MAX8997_REG_STATUS3	= 0x0f,
+	MAX8997_REG_STATUS4	= 0x10,
+
+	MAX8997_REG_MAINCON1	= 0x13,
+	MAX8997_REG_MAINCON2	= 0x14,
+	MAX8997_REG_BUCKRAMP	= 0x15,
+
+	MAX8997_REG_BUCK1CTRL	= 0x18,
+	MAX8997_REG_BUCK1DVS1	= 0x19,
+	MAX8997_REG_BUCK1DVS2	= 0x1a,
+	MAX8997_REG_BUCK1DVS3	= 0x1b,
+	MAX8997_REG_BUCK1DVS4	= 0x1c,
+	MAX8997_REG_BUCK1DVS5	= 0x1d,
+	MAX8997_REG_BUCK1DVS6	= 0x1e,
+	MAX8997_REG_BUCK1DVS7	= 0x1f,
+	MAX8997_REG_BUCK1DVS8	= 0x20,
+	MAX8997_REG_BUCK2CTRL	= 0x21,
+	MAX8997_REG_BUCK2DVS1	= 0x22,
+	MAX8997_REG_BUCK2DVS2	= 0x23,
+	MAX8997_REG_BUCK2DVS3	= 0x24,
+	MAX8997_REG_BUCK2DVS4	= 0x25,
+	MAX8997_REG_BUCK2DVS5	= 0x26,
+	MAX8997_REG_BUCK2DVS6	= 0x27,
+	MAX8997_REG_BUCK2DVS7	= 0x28,
+	MAX8997_REG_BUCK2DVS8	= 0x29,
+	MAX8997_REG_BUCK3CTRL	= 0x2a,
+	MAX8997_REG_BUCK3DVS	= 0x2b,
+	MAX8997_REG_BUCK4CTRL	= 0x2c,
+	MAX8997_REG_BUCK4DVS	= 0x2d,
+	MAX8997_REG_BUCK5CTRL	= 0x2e,
+	MAX8997_REG_BUCK5DVS1	= 0x2f,
+	MAX8997_REG_BUCK5DVS2	= 0x30,
+	MAX8997_REG_BUCK5DVS3	= 0x31,
+	MAX8997_REG_BUCK5DVS4	= 0x32,
+	MAX8997_REG_BUCK5DVS5	= 0x33,
+	MAX8997_REG_BUCK5DVS6	= 0x34,
+	MAX8997_REG_BUCK5DVS7	= 0x35,
+	MAX8997_REG_BUCK5DVS8	= 0x36,
+	MAX8997_REG_BUCK6CTRL	= 0x37,
+	MAX8997_REG_BUCK6BPSKIPCTRL	= 0x38,
+	MAX8997_REG_BUCK7CTRL	= 0x39,
+	MAX8997_REG_BUCK7DVS	= 0x3a,
+	MAX8997_REG_LDO1CTRL	= 0x3b,
+	MAX8997_REG_LDO2CTRL	= 0x3c,
+	MAX8997_REG_LDO3CTRL	= 0x3d,
+	MAX8997_REG_LDO4CTRL	= 0x3e,
+	MAX8997_REG_LDO5CTRL	= 0x3f,
+	MAX8997_REG_LDO6CTRL	= 0x40,
+	MAX8997_REG_LDO7CTRL	= 0x41,
+	MAX8997_REG_LDO8CTRL	= 0x42,
+	MAX8997_REG_LDO9CTRL	= 0x43,
+	MAX8997_REG_LDO10CTRL	= 0x44,
+	MAX8997_REG_LDO11CTRL	= 0x45,
+	MAX8997_REG_LDO12CTRL	= 0x46,
+	MAX8997_REG_LDO13CTRL	= 0x47,
+	MAX8997_REG_LDO14CTRL	= 0x48,
+	MAX8997_REG_LDO15CTRL	= 0x49,
+	MAX8997_REG_LDO16CTRL	= 0x4a,
+	MAX8997_REG_LDO17CTRL	= 0x4b,
+	MAX8997_REG_LDO18CTRL	= 0x4c,
+	MAX8997_REG_LDO21CTRL	= 0x4d,
+
+	MAX8997_REG_MBCCTRL1	= 0x50,
+	MAX8997_REG_MBCCTRL2	= 0x51,
+	MAX8997_REG_MBCCTRL3	= 0x52,
+	MAX8997_REG_MBCCTRL4	= 0x53,
+	MAX8997_REG_MBCCTRL5	= 0x54,
+	MAX8997_REG_MBCCTRL6	= 0x55,
+	MAX8997_REG_OTPCGHCVS	= 0x56,
+
+	MAX8997_REG_SAFEOUTCTRL	= 0x5a,
+
+	MAX8997_REG_LBCNFG1	= 0x5e,
+	MAX8997_REG_LBCNFG2	= 0x5f,
+	MAX8997_REG_BBCCTRL	= 0x60,
+
+	MAX8997_REG_FLASH1_CUR	= 0x63, /* 0x63 ~ 0x6e for FLASH */
+	MAX8997_REG_FLASH2_CUR	= 0x64,
+	MAX8997_REG_MOVIE_CUR	= 0x65,
+	MAX8997_REG_GSMB_CUR	= 0x66,
+	MAX8997_REG_BOOST_CNTL	= 0x67,
+	MAX8997_REG_LEN_CNTL	= 0x68,
+	MAX8997_REG_FLASH_CNTL	= 0x69,
+	MAX8997_REG_WDT_CNTL	= 0x6a,
+	MAX8997_REG_MAXFLASH1	= 0x6b,
+	MAX8997_REG_MAXFLASH2	= 0x6c,
+	MAX8997_REG_FLASHSTATUS	= 0x6d,
+	MAX8997_REG_FLASHSTATUSMASK	= 0x6e,
+
+	MAX8997_REG_GPIOCNTL1	= 0x70,
+	MAX8997_REG_GPIOCNTL2	= 0x71,
+	MAX8997_REG_GPIOCNTL3	= 0x72,
+	MAX8997_REG_GPIOCNTL4	= 0x73,
+	MAX8997_REG_GPIOCNTL5	= 0x74,
+	MAX8997_REG_GPIOCNTL6	= 0x75,
+	MAX8997_REG_GPIOCNTL7	= 0x76,
+	MAX8997_REG_GPIOCNTL8	= 0x77,
+	MAX8997_REG_GPIOCNTL9	= 0x78,
+	MAX8997_REG_GPIOCNTL10	= 0x79,
+	MAX8997_REG_GPIOCNTL11	= 0x7a,
+	MAX8997_REG_GPIOCNTL12	= 0x7b,
+
+	MAX8997_REG_LDO1CONFIG	= 0x80,
+	MAX8997_REG_LDO2CONFIG	= 0x81,
+	MAX8997_REG_LDO3CONFIG	= 0x82,
+	MAX8997_REG_LDO4CONFIG	= 0x83,
+	MAX8997_REG_LDO5CONFIG	= 0x84,
+	MAX8997_REG_LDO6CONFIG	= 0x85,
+	MAX8997_REG_LDO7CONFIG	= 0x86,
+	MAX8997_REG_LDO8CONFIG	= 0x87,
+	MAX8997_REG_LDO9CONFIG	= 0x88,
+	MAX8997_REG_LDO10CONFIG	= 0x89,
+	MAX8997_REG_LDO11CONFIG	= 0x8a,
+	MAX8997_REG_LDO12CONFIG	= 0x8b,
+	MAX8997_REG_LDO13CONFIG	= 0x8c,
+	MAX8997_REG_LDO14CONFIG	= 0x8d,
+	MAX8997_REG_LDO15CONFIG	= 0x8e,
+	MAX8997_REG_LDO16CONFIG	= 0x8f,
+	MAX8997_REG_LDO17CONFIG	= 0x90,
+	MAX8997_REG_LDO18CONFIG	= 0x91,
+	MAX8997_REG_LDO21CONFIG	= 0x92,
+
+	MAX8997_REG_DVSOKTIMER1	= 0x97,
+	MAX8997_REG_DVSOKTIMER2	= 0x98,
+	MAX8997_REG_DVSOKTIMER4	= 0x99,
+	MAX8997_REG_DVSOKTIMER5	= 0x9a,
+
+	MAX8997_REG_PMIC_END	= 0x9b,
+};
+
+enum max8997_muic_reg {
+	MAX8997_MUIC_REG_ID		= 0x0,
+	MAX8997_MUIC_REG_INT1		= 0x1,
+	MAX8997_MUIC_REG_INT2		= 0x2,
+	MAX8997_MUIC_REG_INT3		= 0x3,
+	MAX8997_MUIC_REG_STATUS1	= 0x4,
+	MAX8997_MUIC_REG_STATUS2	= 0x5,
+	MAX8997_MUIC_REG_STATUS3	= 0x6,
+	MAX8997_MUIC_REG_INTMASK1	= 0x7,
+	MAX8997_MUIC_REG_INTMASK2	= 0x8,
+	MAX8997_MUIC_REG_INTMASK3	= 0x9,
+	MAX8997_MUIC_REG_CDETCTRL	= 0xa,
+
+	MAX8997_MUIC_REG_CONTROL1	= 0xc,
+	MAX8997_MUIC_REG_CONTROL2	= 0xd,
+	MAX8997_MUIC_REG_CONTROL3	= 0xe,
+
+	MAX8997_MUIC_REG_END		= 0xf,
+};
+
+enum max8997_haptic_reg {
+	MAX8997_HAPTIC_REG_GENERAL	= 0x00,
+	MAX8997_HAPTIC_REG_CONF1	= 0x01,
+	MAX8997_HAPTIC_REG_CONF2	= 0x02,
+	MAX8997_HAPTIC_REG_DRVCONF	= 0x03,
+	MAX8997_HAPTIC_REG_CYCLECONF1	= 0x04,
+	MAX8997_HAPTIC_REG_CYCLECONF2	= 0x05,
+	MAX8997_HAPTIC_REG_SIGCONF1	= 0x06,
+	MAX8997_HAPTIC_REG_SIGCONF2	= 0x07,
+	MAX8997_HAPTIC_REG_SIGCONF3	= 0x08,
+	MAX8997_HAPTIC_REG_SIGCONF4	= 0x09,
+	MAX8997_HAPTIC_REG_SIGDC1	= 0x0a,
+	MAX8997_HAPTIC_REG_SIGDC2	= 0x0b,
+	MAX8997_HAPTIC_REG_SIGPWMDC1	= 0x0c,
+	MAX8997_HAPTIC_REG_SIGPWMDC2	= 0x0d,
+	MAX8997_HAPTIC_REG_SIGPWMDC3	= 0x0e,
+	MAX8997_HAPTIC_REG_SIGPWMDC4	= 0x0f,
+	MAX8997_HAPTIC_REG_MTR_REV	= 0x10,
+
+	MAX8997_HAPTIC_REG_END		= 0x11,
+};
+
+/* slave addr = 0x0c: using "2nd part" of rev4 datasheet */
+enum max8997_rtc_reg {
+	MAX8997_RTC_CTRLMASK		= 0x02,
+	MAX8997_RTC_CTRL		= 0x03,
+	MAX8997_RTC_UPDATE1		= 0x04,
+	MAX8997_RTC_UPDATE2		= 0x05,
+	MAX8997_RTC_WTSR_SMPL		= 0x06,
+
+	MAX8997_RTC_SEC			= 0x10,
+	MAX8997_RTC_MIN			= 0x11,
+	MAX8997_RTC_HOUR		= 0x12,
+	MAX8997_RTC_DAY_OF_WEEK		= 0x13,
+	MAX8997_RTC_MONTH		= 0x14,
+	MAX8997_RTC_YEAR		= 0x15,
+	MAX8997_RTC_DAY_OF_MONTH	= 0x16,
+	MAX8997_RTC_ALARM1_SEC		= 0x17,
+	MAX8997_RTC_ALARM1_MIN		= 0x18,
+	MAX8997_RTC_ALARM1_HOUR		= 0x19,
+	MAX8997_RTC_ALARM1_DAY_OF_WEEK	= 0x1a,
+	MAX8997_RTC_ALARM1_MONTH	= 0x1b,
+	MAX8997_RTC_ALARM1_YEAR		= 0x1c,
+	MAX8997_RTC_ALARM1_DAY_OF_MONTH	= 0x1d,
+	MAX8997_RTC_ALARM2_SEC		= 0x1e,
+	MAX8997_RTC_ALARM2_MIN		= 0x1f,
+	MAX8997_RTC_ALARM2_HOUR		= 0x20,
+	MAX8997_RTC_ALARM2_DAY_OF_WEEK	= 0x21,
+	MAX8997_RTC_ALARM2_MONTH	= 0x22,
+	MAX8997_RTC_ALARM2_YEAR		= 0x23,
+	MAX8997_RTC_ALARM2_DAY_OF_MONTH	= 0x24,
+};
+
+enum max8997_irq_source {
+	PMIC_INT1 = 0,
+	PMIC_INT2,
+	PMIC_INT3,
+	PMIC_INT4,
+
+	FUEL_GAUGE, /* Ignored (MAX17042 driver handles) */
+
+	MUIC_INT1,
+	MUIC_INT2,
+	MUIC_INT3,
+
+	GPIO_LOW, /* Not implemented */
+	GPIO_HI, /* Not implemented */
+
+	FLASH_STATUS, /* Not implemented */
+
+	MAX8997_IRQ_GROUP_NR,
+};
+
+enum max8997_irq {
+	MAX8997_PMICIRQ_PWRONR,
+	MAX8997_PMICIRQ_PWRONF,
+	MAX8997_PMICIRQ_PWRON1SEC,
+	MAX8997_PMICIRQ_JIGONR,
+	MAX8997_PMICIRQ_JIGONF,
+	MAX8997_PMICIRQ_LOWBAT2,
+	MAX8997_PMICIRQ_LOWBAT1,
+
+	MAX8997_PMICIRQ_JIGR,
+	MAX8997_PMICIRQ_JIGF,
+	MAX8997_PMICIRQ_MR,
+	MAX8997_PMICIRQ_DVS1OK,
+	MAX8997_PMICIRQ_DVS2OK,
+	MAX8997_PMICIRQ_DVS3OK,
+	MAX8997_PMICIRQ_DVS4OK,
+
+	MAX8997_PMICIRQ_CHGINS,
+	MAX8997_PMICIRQ_CHGRM,
+	MAX8997_PMICIRQ_DCINOVP,
+	MAX8997_PMICIRQ_TOPOFFR,
+	MAX8997_PMICIRQ_CHGRSTF,
+	MAX8997_PMICIRQ_MBCHGTMEXPD,
+
+	MAX8997_PMICIRQ_RTC60S,
+	MAX8997_PMICIRQ_RTCA1,
+	MAX8997_PMICIRQ_RTCA2,
+	MAX8997_PMICIRQ_SMPL_INT,
+	MAX8997_PMICIRQ_RTC1S,
+	MAX8997_PMICIRQ_WTSR,
+
+	MAX8997_MUICIRQ_ADCError,
+	MAX8997_MUICIRQ_ADCLow,
+	MAX8997_MUICIRQ_ADC,
+
+	MAX8997_MUICIRQ_VBVolt,
+	MAX8997_MUICIRQ_DBChg,
+	MAX8997_MUICIRQ_DCDTmr,
+	MAX8997_MUICIRQ_ChgDetRun,
+	MAX8997_MUICIRQ_ChgTyp,
+
+	MAX8997_MUICIRQ_OVP,
+
+	MAX8997_IRQ_NR,
+};
+
+#define MAX8997_REG_BUCK1DVS(x)	(MAX8997_REG_BUCK1DVS1 + (x) - 1)
+#define MAX8997_REG_BUCK2DVS(x)	(MAX8997_REG_BUCK2DVS1 + (x) - 1)
+#define MAX8997_REG_BUCK5DVS(x)	(MAX8997_REG_BUCK5DVS1 + (x) - 1)
+
+struct max8997_dev {
+	struct device *dev;
+	struct i2c_client *i2c; /* 0xcc / PMIC, Battery Control, and FLASH */
+	struct i2c_client *rtc; /* slave addr 0x0c */
+	struct i2c_client *haptic; /* slave addr 0x90 */
+	struct i2c_client *muic; /* slave addr 0x4a */
+	struct mutex iolock;
+
+	int type;
+	struct platform_device *battery; /* battery control (not fuel gauge) */
+
+	bool wakeup;
+
+	/* For hibernation */
+	u8 reg_dump[MAX8997_REG_PMIC_END + MAX8997_MUIC_REG_END +
+		MAX8997_HAPTIC_REG_END];
+};
+
+enum max8997_types {
+	TYPE_MAX8997,
+	TYPE_MAX8966,
+};
+
+extern int max8997_read_reg(struct i2c_client *i2c, u8 reg, u8 *dest);
+extern int max8997_bulk_read(struct i2c_client *i2c, u8 reg, int count,
+				u8 *buf);
+extern int max8997_write_reg(struct i2c_client *i2c, u8 reg, u8 value);
+extern int max8997_bulk_write(struct i2c_client *i2c, u8 reg, int count,
+				u8 *buf);
+extern int max8997_update_reg(struct i2c_client *i2c, u8 reg, u8 val, u8 mask);
+
+#endif /*  __LINUX_MFD_MAX8997_PRIV_H */
diff --git a/include/linux/mfd/max8997.h b/include/linux/mfd/max8997.h
new file mode 100644
index 0000000..cb671b3
--- /dev/null
+++ b/include/linux/mfd/max8997.h
@@ -0,0 +1,114 @@
+/*
+ * max8997.h - Driver for the Maxim 8997/8966
+ *
+ *  Copyright (C) 2009-2010 Samsung Electrnoics
+ *  MyungJoo Ham <myungjoo.ham@samsung.com>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA  02111-1307  USA
+ *
+ * This driver is based on max8998.h
+ *
+ * MAX8997 has PMIC, MUIC, HAPTIC, RTC, FLASH, and Fuel Gauge devices.
+ * Except Fuel Gauge, every device shares the same I2C bus and included in
+ * this mfd driver. Although the fuel gauge is included in the chip, it is
+ * excluded from the driver because a) it has a different I2C bus from
+ * others and b) it can be enabled simply by using MAX17042 driver.
+ */
+
+#ifndef __LINUX_MFD_MAX8998_H
+#define __LINUX_MFD_MAX8998_H
+
+#include <linux/regulator/consumer.h>
+
+/* MAX8997/8966 regulator IDs */
+enum max8998_regulators {
+	MAX8997_LDO1 = 0,
+	MAX8997_LDO2,
+	MAX8997_LDO3,
+	MAX8997_LDO4,
+	MAX8997_LDO5,
+	MAX8997_LDO6,
+	MAX8997_LDO7,
+	MAX8997_LDO8,
+	MAX8997_LDO9,
+	MAX8997_LDO10,
+	MAX8997_LDO11,
+	MAX8997_LDO12,
+	MAX8997_LDO13,
+	MAX8997_LDO14,
+	MAX8997_LDO15,
+	MAX8997_LDO16,
+	MAX8997_LDO17,
+	MAX8997_LDO18,
+	MAX8997_LDO21,
+	MAX8997_BUCK1,
+	MAX8997_BUCK2,
+	MAX8997_BUCK3,
+	MAX8997_BUCK4,
+	MAX8997_BUCK5,
+	MAX8997_BUCK6,
+	MAX8997_BUCK7,
+	MAX8997_EN32KHZ_AP,
+	MAX8997_EN32KHZ_CP,
+	MAX8997_ENVICHG,
+	MAX8997_ESAFEOUT1,
+	MAX8997_ESAFEOUT2,
+	MAX8997_CHARGER_CV, /* control MBCCV of MBCCTRL3 */
+	MAX8997_CHARGER, /* charger current, MBCCTRL4 */
+	MAX8997_CHARGER_TOPOFF, /* MBCCTRL5 */
+
+	MAX8997_REG_MAX,
+};
+
+struct max8997_regulator_data {
+	int id;
+	struct regulator_init_data *initdata;
+};
+
+struct max8997_platform_data {
+	bool wakeup;
+	/* IRQ: Not implemented */
+	/* ---- PMIC ---- */
+	struct max8997_regulator_data *regulators;
+	int num_regulators;
+
+	/*
+	 * SET1~3 DVS GPIOs control Buck1, 2, and 5 simultaneously. Therefore,
+	 * With buckx_gpiodvs enabled, the buckx cannot be controlled
+	 * independently. To control buckx (of 1, 2, and 5) independently,
+	 * disable buckx_gpiodvs and control with BUCKxDVS1 register.
+	 *
+	 * When buckx_gpiodvs and bucky_gpiodvs are both enabled, set_voltage
+	 * on buckx will change the voltage of bucky at the same time.
+	 *
+	 */
+	bool ignore_gpiodvs_side_effect;
+	int buck125_gpios[3]; /* GPIO of [0]SET1, [1]SET2, [2]SET3 */
+	int buck125_default_idx; /* Default value of SET1, 2, 3 */
+	unsigned int buck1_voltage[8]; /* buckx_voltage in uV */
+	bool buck1_gpiodvs;
+	unsigned int buck2_voltage[8];
+	bool buck2_gpiodvs;
+	unsigned int buck5_voltage[8];
+	bool buck5_gpiodvs;
+
+	/* MUIC: Not implemented */
+	/* HAPTIC: Not implemented */
+	/* RTC: Not implemented */
+	/* Flash: Not implemented */
+	/* Charger control: Not implemented */
+};
+
+#endif /* __LINUX_MFD_MAX8998_H */
diff --git a/include/linux/mfd/mc13xxx.h b/include/linux/mfd/mc13xxx.h
index a1d391b..c064bea 100644
--- a/include/linux/mfd/mc13xxx.h
+++ b/include/linux/mfd/mc13xxx.h
@@ -146,8 +146,7 @@
 #define MC13XXX_USE_LED		(1 << 5)
 	unsigned int flags;
 
-	int num_regulators;
-	struct mc13xxx_regulator_init_data *regulators;
+	struct mc13xxx_regulator_platform_data regulators;
 	struct mc13xxx_leds_platform_data *leds;
 };
 
diff --git a/include/linux/mfd/tps6105x.h b/include/linux/mfd/tps6105x.h
new file mode 100644
index 0000000..386743d
--- /dev/null
+++ b/include/linux/mfd/tps6105x.h
@@ -0,0 +1,101 @@
+/*
+ * Copyright (C) 2011 ST-Ericsson SA
+ * Written on behalf of Linaro for ST-Ericsson
+ *
+ * Author: Linus Walleij <linus.walleij@linaro.org>
+ *
+ * License terms: GNU General Public License (GPL) version 2
+ */
+#ifndef MFD_TPS6105X_H
+#define MFD_TPS6105X_H
+
+#include <linux/i2c.h>
+#include <linux/regulator/machine.h>
+
+/*
+ * Register definitions to all subdrivers
+ */
+#define TPS6105X_REG_0			0x00
+#define TPS6105X_REG0_MODE_SHIFT	6
+#define TPS6105X_REG0_MODE_MASK		(0x03<<6)
+/* These defines for both reg0 and reg1 */
+#define TPS6105X_REG0_MODE_SHUTDOWN	0x00
+#define TPS6105X_REG0_MODE_TORCH	0x01
+#define TPS6105X_REG0_MODE_TORCH_FLASH	0x02
+#define TPS6105X_REG0_MODE_VOLTAGE	0x03
+#define TPS6105X_REG0_VOLTAGE_SHIFT	4
+#define TPS6105X_REG0_VOLTAGE_MASK	(3<<4)
+#define TPS6105X_REG0_VOLTAGE_450	0
+#define TPS6105X_REG0_VOLTAGE_500	1
+#define TPS6105X_REG0_VOLTAGE_525	2
+#define TPS6105X_REG0_VOLTAGE_500_2	3
+#define TPS6105X_REG0_DIMMING_SHIFT	3
+#define TPS6105X_REG0_TORCHC_SHIFT	0
+#define TPS6105X_REG0_TORCHC_MASK	(7<<0)
+#define TPS6105X_REG0_TORCHC_0		0x00
+#define TPS6105X_REG0_TORCHC_50		0x01
+#define TPS6105X_REG0_TORCHC_75		0x02
+#define TPS6105X_REG0_TORCHC_100	0x03
+#define TPS6105X_REG0_TORCHC_150	0x04
+#define TPS6105X_REG0_TORCHC_200	0x05
+#define TPS6105X_REG0_TORCHC_250_400	0x06
+#define TPS6105X_REG0_TORCHC_250_500	0x07
+#define TPS6105X_REG_1			0x01
+#define TPS6105X_REG1_MODE_SHIFT	6
+#define TPS6105X_REG1_MODE_MASK		(0x03<<6)
+#define TPS6105X_REG1_MODE_SHUTDOWN	0x00
+#define TPS6105X_REG1_MODE_TORCH	0x01
+#define TPS6105X_REG1_MODE_TORCH_FLASH	0x02
+#define TPS6105X_REG1_MODE_VOLTAGE	0x03
+#define TPS6105X_REG_2			0x02
+#define TPS6105X_REG_3			0x03
+
+/**
+ * enum tps6105x_mode - desired mode for the TPS6105x
+ * @TPS6105X_MODE_SHUTDOWN: this instance is inactive, not used for anything
+ * @TPS61905X_MODE_TORCH: this instance is used as a LED, usually a while
+ *	LED, for example as backlight or flashlight. If this is set, the
+ *	TPS6105X will register to the LED framework
+ * @TPS6105X_MODE_TORCH_FLASH: this instance is used as a flashgun, usually
+ *	in a camera
+ * @TPS6105X_MODE_VOLTAGE: this instance is used as a voltage regulator and
+ *	will register to the regulator framework
+ */
+enum tps6105x_mode {
+	TPS6105X_MODE_SHUTDOWN,
+	TPS6105X_MODE_TORCH,
+	TPS6105X_MODE_TORCH_FLASH,
+	TPS6105X_MODE_VOLTAGE,
+};
+
+/**
+ * struct tps6105x_platform_data - TPS61905x platform data
+ * @mode: what mode this instance shall be operated in,
+ *	this is not selectable at runtime
+ * @regulator_data: initialization data for the voltage
+ *	regulator if used as a voltage source
+ */
+struct tps6105x_platform_data {
+	enum tps6105x_mode mode;
+	struct regulator_init_data *regulator_data;
+};
+
+/**
+ * struct tps6105x - state holder for the TPS6105x drivers
+ * @mutex: mutex to serialize I2C accesses
+ * @i2c_client: corresponding I2C client
+ * @regulator: regulator device if used in voltage mode
+ */
+struct tps6105x {
+	struct tps6105x_platform_data *pdata;
+	struct mutex		lock;
+	struct i2c_client	*client;
+	struct regulator_dev	*regulator;
+};
+
+extern int tps6105x_set(struct tps6105x *tps6105x, u8 reg, u8 value);
+extern int tps6105x_get(struct tps6105x *tps6105x, u8 reg, u8 *buf);
+extern int tps6105x_mask_and_set(struct tps6105x *tps6105x, u8 reg,
+				 u8 bitmask, u8 bitvalues);
+
+#endif
diff --git a/include/linux/mfd/wm831x/pdata.h b/include/linux/mfd/wm831x/pdata.h
index 173086d..afe4db4 100644
--- a/include/linux/mfd/wm831x/pdata.h
+++ b/include/linux/mfd/wm831x/pdata.h
@@ -104,11 +104,17 @@
 #define WM831X_MAX_ISINK  2
 
 struct wm831x_pdata {
+	/** Used to distinguish multiple WM831x chips */
+	int wm831x_num;
+
 	/** Called before subdevices are set up */
 	int (*pre_init)(struct wm831x *wm831x);
 	/** Called after subdevices are set up */
 	int (*post_init)(struct wm831x *wm831x);
 
+	/** Put the /IRQ line into CMOS mode */
+	bool irq_cmos;
+
 	int irq_base;
 	int gpio_base;
 	struct wm831x_backlight_pdata *backlight;
diff --git a/include/linux/mfd/wm8994/core.h b/include/linux/mfd/wm8994/core.h
index ef4f0b6..f0b69cd 100644
--- a/include/linux/mfd/wm8994/core.h
+++ b/include/linux/mfd/wm8994/core.h
@@ -59,7 +59,7 @@
 	int (*read_dev)(struct wm8994 *wm8994, unsigned short reg,
 			int bytes, void *dest);
 	int (*write_dev)(struct wm8994 *wm8994, unsigned short reg,
-			 int bytes, void *src);
+			 int bytes, const void *src);
 
 	void *control_data;
 
@@ -88,6 +88,8 @@
 		    unsigned short mask, unsigned short val);
 int wm8994_bulk_read(struct wm8994 *wm8994, unsigned short reg,
 		     int count, u16 *buf);
+int wm8994_bulk_write(struct wm8994 *wm8994, unsigned short reg,
+		     int count, const u16 *buf);
 
 
 /* Helper to save on boilerplate */
diff --git a/include/linux/pci_ids.h b/include/linux/pci_ids.h
index bda221d..11fd381 100644
--- a/include/linux/pci_ids.h
+++ b/include/linux/pci_ids.h
@@ -2737,6 +2737,7 @@
 #define PCI_DEVICE_ID_INTEL_82372FB_1	0x7601
 #define PCI_DEVICE_ID_INTEL_SCH_LPC	0x8119
 #define PCI_DEVICE_ID_INTEL_SCH_IDE	0x811a
+#define PCI_DEVICE_ID_INTEL_ITC_LPC	0x8186
 #define PCI_DEVICE_ID_INTEL_82454GX	0x84c4
 #define PCI_DEVICE_ID_INTEL_82450GX	0x84c5
 #define PCI_DEVICE_ID_INTEL_82451NX	0x84ca
diff --git a/sound/soc/codecs/cq93vc.c b/sound/soc/codecs/cq93vc.c
index 347a567..b8066ef 100644
--- a/sound/soc/codecs/cq93vc.c
+++ b/sound/soc/codecs/cq93vc.c
@@ -153,7 +153,8 @@
 
 static int cq93vc_probe(struct snd_soc_codec *codec)
 {
-	struct davinci_vc *davinci_vc = snd_soc_codec_get_drvdata(codec);
+	struct davinci_vc *davinci_vc =
+			mfd_get_data(to_platform_device(codec->dev));
 
 	davinci_vc->cq93vc.codec = codec;
 	codec->control_data = davinci_vc;
diff --git a/sound/soc/codecs/twl4030.c b/sound/soc/codecs/twl4030.c
index e4d464b..8512800 100644
--- a/sound/soc/codecs/twl4030.c
+++ b/sound/soc/codecs/twl4030.c
@@ -26,6 +26,7 @@
 #include <linux/pm.h>
 #include <linux/i2c.h>
 #include <linux/platform_device.h>
+#include <linux/mfd/core.h>
 #include <linux/i2c/twl.h>
 #include <linux/slab.h>
 #include <sound/core.h>
@@ -732,7 +733,8 @@
 
 static void headset_ramp(struct snd_soc_codec *codec, int ramp)
 {
-	struct twl4030_codec_audio_data *pdata = codec->dev->platform_data;
+	struct twl4030_codec_audio_data *pdata =
+			mfd_get_data(to_platform_device(codec->dev));
 	unsigned char hs_gain, hs_pop;
 	struct twl4030_priv *twl4030 = snd_soc_codec_get_drvdata(codec);
 	/* Base values for ramp delay calculation: 2^19 - 2^26 */
@@ -2297,7 +2299,7 @@
 
 static int __devinit twl4030_codec_probe(struct platform_device *pdev)
 {
-	struct twl4030_codec_audio_data *pdata = pdev->dev.platform_data;
+	struct twl4030_codec_audio_data *pdata = mfd_get_data(pdev);
 
 	if (!pdata) {
 		dev_err(&pdev->dev, "platform_data is missing\n");
diff --git a/sound/soc/codecs/wl1273.c b/sound/soc/codecs/wl1273.c
index 861b28f..1ad0d5a 100644
--- a/sound/soc/codecs/wl1273.c
+++ b/sound/soc/codecs/wl1273.c
@@ -436,7 +436,8 @@
 
 static int wl1273_probe(struct snd_soc_codec *codec)
 {
-	struct wl1273_core **core = codec->dev->platform_data;
+	struct wl1273_core **core =
+			mfd_get_data(to_platform_device(codec->dev));
 	struct wl1273_priv *wl1273;
 	int r;
 
diff --git a/sound/soc/codecs/wm8400.c b/sound/soc/codecs/wm8400.c
index 3c3bc07..736b785 100644
--- a/sound/soc/codecs/wm8400.c
+++ b/sound/soc/codecs/wm8400.c
@@ -22,6 +22,7 @@
 #include <linux/regulator/consumer.h>
 #include <linux/mfd/wm8400-audio.h>
 #include <linux/mfd/wm8400-private.h>
+#include <linux/mfd/core.h>
 #include <sound/core.h>
 #include <sound/pcm.h>
 #include <sound/pcm_params.h>
@@ -1377,7 +1378,7 @@
 
 static int wm8400_codec_probe(struct snd_soc_codec *codec)
 {
-	struct wm8400 *wm8400 = dev_get_platdata(codec->dev);
+	struct wm8400 *wm8400 = mfd_get_data(to_platform_device(codec->dev));
 	struct wm8400_priv *priv;
 	int ret;
 	u16 reg;
diff --git a/sound/soc/davinci/davinci-vcif.c b/sound/soc/davinci/davinci-vcif.c
index 9d2afcc..13e05a3 100644
--- a/sound/soc/davinci/davinci-vcif.c
+++ b/sound/soc/davinci/davinci-vcif.c
@@ -205,7 +205,7 @@
 
 static int davinci_vcif_probe(struct platform_device *pdev)
 {
-	struct davinci_vc *davinci_vc = platform_get_drvdata(pdev);
+	struct davinci_vc *davinci_vc = mfd_get_data(pdev);
 	struct davinci_vcif_dev *davinci_vcif_dev;
 	int ret;