V4L/DVB (7647): Add support for the Hauppauge HVR-1700 digital mode
This adds support for DVB-T mode only, analog is not supported.
Signed-off-by: Steven Toth <stoth@hauppauge.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
diff --git a/drivers/media/video/cx23885/cx23885-cards.c b/drivers/media/video/cx23885/cx23885-cards.c
index 8cb32f3..84636ff 100644
--- a/drivers/media/video/cx23885/cx23885-cards.c
+++ b/drivers/media/video/cx23885/cx23885-cards.c
@@ -134,6 +134,10 @@
.name = "Hauppauge WinTV-HVR1200",
.portc = CX23885_MPEG_DVB,
},
+ [CX23885_BOARD_HAUPPAUGE_HVR1700] = {
+ .name = "Hauppauge WinTV-HVR1700",
+ .portc = CX23885_MPEG_DVB,
+ },
};
const unsigned int cx23885_bcount = ARRAY_SIZE(cx23885_boards);
@@ -189,6 +193,10 @@
.subvendor = 0x0070,
.subdevice = 0x71d1,
.card = CX23885_BOARD_HAUPPAUGE_HVR1200,
+ }, {
+ .subvendor = 0x0070,
+ .subdevice = 0x8101,
+ .card = CX23885_BOARD_HAUPPAUGE_HVR1700,
},
};
const unsigned int cx23885_idcount = ARRAY_SIZE(cx23885_subids);
@@ -243,6 +251,9 @@
case 79561: /* WinTV-HVR1250 (PCIe, OEM, No IR, half height, ATSC and Basic analog */
case 79571: /* WinTV-HVR1250 (PCIe, OEM, No IR, full height, ATSC and Basic analog */
case 79671: /* WinTV-HVR1250 (PCIe, OEM, No IR, half height, ATSC and Basic analog */
+ case 81519:
+ /* WinTV-HVR1700 (PCIe, Retail, No IR, half height,
+ * DVB-T and MPEG2 HW Encoder */
break;
default:
printk("%s: warning: unknown hauppauge model #%d\n", dev->name, tv.model);
@@ -333,6 +344,27 @@
mdelay(20);
cx_set(GP0_IO, 0x00050005);
break;
+ case CX23885_BOARD_HAUPPAUGE_HVR1700:
+ /* GPIO-0 TDA10048 demodulator reset */
+ /* GPIO-2 TDA8295A Reset */
+ /* GPIO-3-10 cx23417 data0-7 */
+ /* GPIO-11-14 cx23417 addr0-3 */
+ /* GPIO-15-18 cx23417 READY, CS, RD, WR */
+
+ /* The following GPIO's are on the interna AVCore (cx25840) */
+ /* GPIO-19 IR_RX */
+ /* GPIO-20 IR_TX 416/DVBT Select */
+ /* GPIO-21 IIS DAT */
+ /* GPIO-22 IIS WCLK */
+ /* GPIO-23 IIS BCLK */
+
+ /* Put the parts into reset and back */
+ cx_set(GP0_IO, 0x00050000);
+ mdelay(20);
+ cx_clear(GP0_IO, 0x00000005);
+ mdelay(20);
+ cx_set(GP0_IO, 0x00050005);
+ break;
}
}
@@ -374,6 +406,7 @@
case CX23885_BOARD_HAUPPAUGE_HVR1800:
case CX23885_BOARD_HAUPPAUGE_HVR1800lp:
case CX23885_BOARD_HAUPPAUGE_HVR1200:
+ case CX23885_BOARD_HAUPPAUGE_HVR1700:
if (dev->i2c_bus[0].i2c_rc == 0)
hauppauge_eeprom(dev, eeprom+0xc0);
break;
@@ -391,6 +424,7 @@
case CX23885_BOARD_HAUPPAUGE_HVR1800:
case CX23885_BOARD_HAUPPAUGE_HVR1800lp:
case CX23885_BOARD_HAUPPAUGE_HVR1200:
+ case CX23885_BOARD_HAUPPAUGE_HVR1700:
default:
ts2->gen_ctrl_val = 0xc; /* Serial bus + punctured clock */
ts2->ts_clk_en_val = 0x1; /* Enable TS_CLK */