Merge master.kernel.org:/pub/scm/linux/kernel/git/lethal/sh-2.6
* master.kernel.org:/pub/scm/linux/kernel/git/lethal/sh-2.6: (26 commits)
sh: remove dead config symbols from SH code
sh: Kill off broken snapgear ds1302 code.
sh: Add a dummy vga.h.
rtc: rtc-sh: Zero out tm value for invalid rtc states.
rtc: sh-rtc: Handle rtc_device_register() failure properly.
sh: Fix heartbeart on Solution Engine series
sh: Remove SCI_NPORTS from sh-sci.h
sh: Fix up PAGE_KERNEL_PCC() for nommu.
sh: hs7751rvoip: Kill off dead IPR IRQ mappings.
sh: hs7751rvoip: irq.c needs linux/interrupt.h.
sh: Kill off __{copy,clear}_user_page().
sh: Optimized copy_{to,from}_user_page() for SH-4.
sh: Wire up clear_user_highpage().
sh: Kill off the remaining ST40 cruft.
superhyway: Handle device_register() retval properly.
sh: kgdb sysrq depends on magic sysrq.
sh: Add -Werror for clean directories.
sh: Fix up kgdb build with modular sh-sci.
sh: Export __{s,u}divsi3_i4i on all CPUs.
sh: Fix up kgdb-on-NMI branch target.
...
diff --git a/arch/sh/Kconfig b/arch/sh/Kconfig
index 22a3eb3..496d635 100644
--- a/arch/sh/Kconfig
+++ b/arch/sh/Kconfig
@@ -211,10 +211,12 @@
bool "SolutionEngine"
select SOLUTION_ENGINE
select CPU_HAS_IPR_IRQ
- depends on CPU_SUBTYPE_SH7709 || CPU_SUBTYPE_SH7750
+ depends on CPU_SUBTYPE_SH7705 || CPU_SUBTYPE_SH7709 || CPU_SUBTYPE_SH7710 || \
+ CPU_SUBTYPE_SH7712 || CPU_SUBTYPE_SH7750 || CPU_SUBTYPE_SH7750S || \
+ CPU_SUBTYPE_SH7750R
help
- Select SolutionEngine if configuring for a Hitachi SH7709
- or SH7750 evaluation board.
+ Select SolutionEngine if configuring for a Hitachi SH7705, SH7709,
+ SH7710, SH7712, SH7750, SH7750S or SH7750R evaluation board.
config SH_7206_SOLUTION_ENGINE
bool "SolutionEngine7206"
@@ -603,7 +605,7 @@
config UBC_WAKEUP
bool "Wakeup UBC on startup"
- depends on CPU_SH4
+ depends on CPU_SH4 && !CPU_SH4A
help
Selecting this option will wakeup the User Break Controller (UBC) on
startup. Although the UBC is left in an awake state when the processor
diff --git a/arch/sh/Kconfig.debug b/arch/sh/Kconfig.debug
index ab2f9f3..722da68 100644
--- a/arch/sh/Kconfig.debug
+++ b/arch/sh/Kconfig.debug
@@ -124,12 +124,13 @@
config SH_KGDB_CONSOLE
bool "Console messages through GDB"
- depends on !SERIAL_SH_SCI_CONSOLE
+ depends on !SERIAL_SH_SCI_CONSOLE && SERIAL_SH_SCI=y
select SERIAL_CORE_CONSOLE
default n
config KGDB_SYSRQ
bool "Allow SysRq 'G' to enter KGDB"
+ depends on MAGIC_SYSRQ
default y
comment "Serial port setup"
diff --git a/arch/sh/boards/renesas/hs7751rvoip/irq.c b/arch/sh/boards/renesas/hs7751rvoip/irq.c
index 943f93a..e55c668 100644
--- a/arch/sh/boards/renesas/hs7751rvoip/irq.c
+++ b/arch/sh/boards/renesas/hs7751rvoip/irq.c
@@ -12,6 +12,7 @@
#include <linux/init.h>
#include <linux/irq.h>
+#include <linux/interrupt.h>
#include <asm/io.h>
#include <asm/irq.h>
#include <asm/hs7751rvoip.h>
diff --git a/arch/sh/boards/renesas/hs7751rvoip/setup.c b/arch/sh/boards/renesas/hs7751rvoip/setup.c
index fa5fa39..c056259 100644
--- a/arch/sh/boards/renesas/hs7751rvoip/setup.c
+++ b/arch/sh/boards/renesas/hs7751rvoip/setup.c
@@ -15,20 +15,6 @@
#include <asm/io.h>
#include <asm/machvec.h>
-static struct ipr_data hs77501rvoip_ipr_map[] = {
-#if defined(CONFIG_HS7751RVOIP_CODEC)
- { DMTE0_IRQ, DMA_IPR_ADDR, DMA_IPR_POS, DMA_PRIORITY },
- { DMTE1_IRQ, DMA_IPR_ADDR, DMA_IPR_POS, DMA_PRIORITY },
-#endif
-};
-
-static void __init hs7751rvoip_init_irq(void)
-{
- make_ipr_irq(hs77501rvoip_ipr_map, ARRAY_SIZE(hs77501rvoip_ipr_map));
-
- init_hs7751rvoip_IRQ();
-}
-
static void hs7751rvoip_power_off(void)
{
ctrl_outw(ctrl_inw(PA_OUTPORTR) & 0xffdf, PA_OUTPORTR);
@@ -75,14 +61,13 @@
return 0;
}
+device_initcall(hs7751rvoip_cf_init);
/*
* Initialize the board
*/
static void __init hs7751rvoip_setup(char **cmdline_p)
{
- device_initcall(hs7751rvoip_cf_init);
-
ctrl_outb(0xf0, PA_OUTPORTR);
pm_power_off = hs7751rvoip_power_off;
@@ -115,6 +100,6 @@
.mv_outsw = hs7751rvoip_outsw,
.mv_outsl = hs7751rvoip_outsl,
- .mv_init_irq = hs7751rvoip_init_irq,
+ .mv_init_irq = init_hs7751rvoip_IRQ,
.mv_ioport_map = hs7751rvoip_ioport_map,
};
diff --git a/arch/sh/boards/renesas/sh7710voipgw/setup.c b/arch/sh/boards/renesas/sh7710voipgw/setup.c
index 2dce8bd..0d56fd8 100644
--- a/arch/sh/boards/renesas/sh7710voipgw/setup.c
+++ b/arch/sh/boards/renesas/sh7710voipgw/setup.c
@@ -11,7 +11,6 @@
#include <asm/machvec.h>
#include <asm/irq.h>
#include <asm/io.h>
-#include <asm/irq.h>
static struct ipr_data sh7710voipgw_ipr_map[] = {
{ TIMER2_IRQ, TIMER2_IPR_ADDR, TIMER2_IPR_POS, TIMER2_PRIORITY },
diff --git a/arch/sh/boards/se/7206/irq.c b/arch/sh/boards/se/7206/irq.c
index 27da884..9d5bfc7 100644
--- a/arch/sh/boards/se/7206/irq.c
+++ b/arch/sh/boards/se/7206/irq.c
@@ -9,7 +9,6 @@
#include <linux/init.h>
#include <linux/irq.h>
#include <linux/io.h>
-#include <linux/irq.h>
#include <linux/interrupt.h>
#include <asm/se7206.h>
diff --git a/arch/sh/boards/se/770x/setup.c b/arch/sh/boards/se/770x/setup.c
index d07a336..318bc8a 100644
--- a/arch/sh/boards/se/770x/setup.c
+++ b/arch/sh/boards/se/770x/setup.c
@@ -94,6 +94,7 @@
static struct heartbeat_data heartbeat_data = {
.bit_pos = heartbeat_bit_pos,
.nr_bits = ARRAY_SIZE(heartbeat_bit_pos),
+ .regsize = 16,
};
static struct resource heartbeat_resources[] = {
diff --git a/arch/sh/boards/se/7722/setup.c b/arch/sh/boards/se/7722/setup.c
index 20f0640..eb97dca 100644
--- a/arch/sh/boards/se/7722/setup.c
+++ b/arch/sh/boards/se/7722/setup.c
@@ -16,8 +16,13 @@
#include <asm/machvec.h>
#include <asm/se7722.h>
#include <asm/io.h>
+#include <asm/heartbeat.h>
/* Heartbeat */
+static struct heartbeat_data heartbeat_data = {
+ .regsize = 16,
+};
+
static struct resource heartbeat_resources[] = {
[0] = {
.start = PA_LED,
@@ -29,6 +34,9 @@
static struct platform_device heartbeat_device = {
.name = "heartbeat",
.id = -1,
+ .dev = {
+ .platform_data = &heartbeat_data,
+ },
.num_resources = ARRAY_SIZE(heartbeat_resources),
.resource = heartbeat_resources,
};
diff --git a/arch/sh/boards/se/7780/setup.c b/arch/sh/boards/se/7780/setup.c
index 76e53b2..0f08ab3 100644
--- a/arch/sh/boards/se/7780/setup.c
+++ b/arch/sh/boards/se/7780/setup.c
@@ -14,8 +14,13 @@
#include <asm/machvec.h>
#include <asm/se7780.h>
#include <asm/io.h>
+#include <asm/heartbeat.h>
/* Heartbeat */
+static struct heartbeat_data heartbeat_data = {
+ .regsize = 16,
+};
+
static struct resource heartbeat_resources[] = {
[0] = {
.start = PA_LED,
@@ -27,6 +32,9 @@
static struct platform_device heartbeat_device = {
.name = "heartbeat",
.id = -1,
+ .dev = {
+ .platform_data = &heartbeat_data,
+ },
.num_resources = ARRAY_SIZE(heartbeat_resources),
.resource = heartbeat_resources,
};
diff --git a/arch/sh/boards/snapgear/Makefile b/arch/sh/boards/snapgear/Makefile
index 59fc976..d2d2f4b 100644
--- a/arch/sh/boards/snapgear/Makefile
+++ b/arch/sh/boards/snapgear/Makefile
@@ -2,5 +2,4 @@
# Makefile for the SnapGear specific parts of the kernel
#
-obj-y := setup.o io.o rtc.o
-
+obj-y := setup.o io.o
diff --git a/arch/sh/boards/snapgear/rtc.c b/arch/sh/boards/snapgear/rtc.c
deleted file mode 100644
index edb3dd9..0000000
--- a/arch/sh/boards/snapgear/rtc.c
+++ /dev/null
@@ -1,309 +0,0 @@
-/****************************************************************************/
-/*
- * linux/arch/sh/boards/snapgear/rtc.c -- Secureedge5410 RTC code
- *
- * Copyright (C) 2002 David McCullough <davidm@snapgear.com>
- * Copyright (C) 2003 Paul Mundt <lethal@linux-sh.org>
- *
- * The SecureEdge5410 can have one of 2 real time clocks, the SH
- * built in version or the preferred external DS1302. Here we work out
- * each to see what we have and then run with it.
- */
-/****************************************************************************/
-
-#include <linux/init.h>
-#include <linux/kernel.h>
-#include <linux/sched.h>
-#include <linux/time.h>
-#include <linux/rtc.h>
-#include <linux/mc146818rtc.h>
-#include <asm/io.h>
-
-static int use_ds1302;
-
-/****************************************************************************/
-/*
- * we need to implement a DS1302 driver here that can operate in
- * conjunction with the builtin rtc driver which is already quite friendly
- */
-/*****************************************************************************/
-
-#define RTC_CMD_READ 0x81 /* Read command */
-#define RTC_CMD_WRITE 0x80 /* Write command */
-
-#define RTC_ADDR_YEAR 0x06 /* Address of year register */
-#define RTC_ADDR_DAY 0x05 /* Address of day of week register */
-#define RTC_ADDR_MON 0x04 /* Address of month register */
-#define RTC_ADDR_DATE 0x03 /* Address of day of month register */
-#define RTC_ADDR_HOUR 0x02 /* Address of hour register */
-#define RTC_ADDR_MIN 0x01 /* Address of minute register */
-#define RTC_ADDR_SEC 0x00 /* Address of second register */
-
-#define RTC_RESET 0x1000
-#define RTC_IODATA 0x0800
-#define RTC_SCLK 0x0400
-
-#define set_dirp(x)
-#define get_dirp(x) 0
-#define set_dp(x) SECUREEDGE_WRITE_IOPORT(x, 0x1c00)
-#define get_dp(x) SECUREEDGE_READ_IOPORT()
-
-static void ds1302_sendbits(unsigned int val)
-{
- int i;
-
- for (i = 8; (i); i--, val >>= 1) {
- set_dp((get_dp() & ~RTC_IODATA) | ((val & 0x1) ? RTC_IODATA : 0));
- set_dp(get_dp() | RTC_SCLK); // clock high
- set_dp(get_dp() & ~RTC_SCLK); // clock low
- }
-}
-
-static unsigned int ds1302_recvbits(void)
-{
- unsigned int val;
- int i;
-
- for (i = 0, val = 0; (i < 8); i++) {
- val |= (((get_dp() & RTC_IODATA) ? 1 : 0) << i);
- set_dp(get_dp() | RTC_SCLK); // clock high
- set_dp(get_dp() & ~RTC_SCLK); // clock low
- }
- return(val);
-}
-
-static unsigned int ds1302_readbyte(unsigned int addr)
-{
- unsigned int val;
- unsigned long flags;
-
- local_irq_save(flags);
- set_dirp(get_dirp() | RTC_RESET | RTC_IODATA | RTC_SCLK);
- set_dp(get_dp() & ~(RTC_RESET | RTC_IODATA | RTC_SCLK));
-
- set_dp(get_dp() | RTC_RESET);
- ds1302_sendbits(((addr & 0x3f) << 1) | RTC_CMD_READ);
- set_dirp(get_dirp() & ~RTC_IODATA);
- val = ds1302_recvbits();
- set_dp(get_dp() & ~RTC_RESET);
- local_irq_restore(flags);
-
- return(val);
-}
-
-static void ds1302_writebyte(unsigned int addr, unsigned int val)
-{
- unsigned long flags;
-
- local_irq_save(flags);
- set_dirp(get_dirp() | RTC_RESET | RTC_IODATA | RTC_SCLK);
- set_dp(get_dp() & ~(RTC_RESET | RTC_IODATA | RTC_SCLK));
- set_dp(get_dp() | RTC_RESET);
- ds1302_sendbits(((addr & 0x3f) << 1) | RTC_CMD_WRITE);
- ds1302_sendbits(val);
- set_dp(get_dp() & ~RTC_RESET);
- local_irq_restore(flags);
-}
-
-static void ds1302_reset(void)
-{
- unsigned long flags;
- /* Hardware dependent reset/init */
- local_irq_save(flags);
- set_dirp(get_dirp() | RTC_RESET | RTC_IODATA | RTC_SCLK);
- set_dp(get_dp() & ~(RTC_RESET | RTC_IODATA | RTC_SCLK));
- local_irq_restore(flags);
-}
-
-/*****************************************************************************/
-
-static inline int bcd2int(int val)
-{
- return((((val & 0xf0) >> 4) * 10) + (val & 0xf));
-}
-
-static inline int int2bcd(int val)
-{
- return(((val / 10) << 4) + (val % 10));
-}
-
-/*****************************************************************************/
-/*
- * Write and Read some RAM in the DS1302, if it works assume it's there
- * Otherwise use the SH4 internal RTC
- */
-
-void snapgear_rtc_gettimeofday(struct timespec *);
-int snapgear_rtc_settimeofday(const time_t);
-
-void __init secureedge5410_rtc_init(void)
-{
- unsigned char *test = "snapgear";
- int i;
-
- ds1302_reset();
-
- use_ds1302 = 1;
-
- for (i = 0; test[i]; i++)
- ds1302_writebyte(32 + i, test[i]);
-
- for (i = 0; test[i]; i++)
- if (ds1302_readbyte(32 + i) != test[i]) {
- use_ds1302 = 0;
- break;
- }
-
- if (use_ds1302) {
- rtc_sh_get_time = snapgear_rtc_gettimeofday;
- rtc_sh_set_time = snapgear_rtc_settimeofday;
- }
-
- printk("SnapGear RTC: using %s rtc.\n", use_ds1302 ? "ds1302" : "internal");
-}
-
-/****************************************************************************/
-/*
- * our generic interface that chooses the correct code to use
- */
-
-void snapgear_rtc_gettimeofday(struct timespec *ts)
-{
- unsigned int sec, min, hr, day, mon, yr;
-
- if (!use_ds1302)
- return;
-
- sec = bcd2int(ds1302_readbyte(RTC_ADDR_SEC));
- min = bcd2int(ds1302_readbyte(RTC_ADDR_MIN));
- hr = bcd2int(ds1302_readbyte(RTC_ADDR_HOUR));
- day = bcd2int(ds1302_readbyte(RTC_ADDR_DATE));
- mon = bcd2int(ds1302_readbyte(RTC_ADDR_MON));
- yr = bcd2int(ds1302_readbyte(RTC_ADDR_YEAR));
-
-bad_time:
- if (yr > 99 || mon < 1 || mon > 12 || day > 31 || day < 1 ||
- hr > 23 || min > 59 || sec > 59) {
- printk(KERN_ERR
- "SnapGear RTC: invalid value, resetting to 1 Jan 2000\n");
- ds1302_writebyte(RTC_ADDR_MIN, min = 0);
- ds1302_writebyte(RTC_ADDR_HOUR, hr = 0);
- ds1302_writebyte(RTC_ADDR_DAY, 7);
- ds1302_writebyte(RTC_ADDR_DATE, day = 1);
- ds1302_writebyte(RTC_ADDR_MON, mon = 1);
- ds1302_writebyte(RTC_ADDR_YEAR, yr = 0);
- ds1302_writebyte(RTC_ADDR_SEC, sec = 0);
- }
-
- ts->tv_sec = mktime(2000 + yr, mon, day, hr, min, sec);
- if (ts->tv_sec < 0) {
-#if 0
- printk("BAD TIME %d %d %d %d %d %d\n", yr, mon, day, hr, min, sec);
-#endif
- yr = 100;
- goto bad_time;
- }
- ts->tv_nsec = 0;
-}
-
-int snapgear_rtc_settimeofday(const time_t secs)
-{
- int retval = 0;
- int real_seconds, real_minutes, cmos_minutes;
- unsigned long nowtime;
-
- if (!use_ds1302)
- return 0;
-
-/*
- * This is called direct from the kernel timer handling code.
- * It is supposed to synchronize the kernel clock to the RTC.
- */
-
- nowtime = secs;
-
- /* STOP RTC */
- ds1302_writebyte(RTC_ADDR_SEC, ds1302_readbyte(RTC_ADDR_SEC) | 0x80);
-
- cmos_minutes = bcd2int(ds1302_readbyte(RTC_ADDR_MIN));
-
- /*
- * since we're only adjusting minutes and seconds,
- * don't interfere with hour overflow. This avoids
- * messing with unknown time zones but requires your
- * RTC not to be off by more than 15 minutes
- */
- real_seconds = nowtime % 60;
- real_minutes = nowtime / 60;
- if (((abs(real_minutes - cmos_minutes) + 15)/30) & 1)
- real_minutes += 30; /* correct for half hour time zone */
- real_minutes %= 60;
-
- if (abs(real_minutes - cmos_minutes) < 30) {
- ds1302_writebyte(RTC_ADDR_MIN, int2bcd(real_minutes));
- ds1302_writebyte(RTC_ADDR_SEC, int2bcd(real_seconds));
- } else {
- printk(KERN_WARNING
- "SnapGear RTC: can't update from %d to %d\n",
- cmos_minutes, real_minutes);
- retval = -1;
- }
-
- /* START RTC */
- ds1302_writebyte(RTC_ADDR_SEC, ds1302_readbyte(RTC_ADDR_SEC) & ~0x80);
- return(0);
-}
-
-unsigned char secureedge5410_cmos_read(int addr)
-{
- unsigned char val = 0;
-
- if (!use_ds1302)
- return(__CMOS_READ(addr, w));
-
- switch(addr) {
- case RTC_SECONDS: val = ds1302_readbyte(RTC_ADDR_SEC); break;
- case RTC_SECONDS_ALARM: break;
- case RTC_MINUTES: val = ds1302_readbyte(RTC_ADDR_MIN); break;
- case RTC_MINUTES_ALARM: break;
- case RTC_HOURS: val = ds1302_readbyte(RTC_ADDR_HOUR); break;
- case RTC_HOURS_ALARM: break;
- case RTC_DAY_OF_WEEK: val = ds1302_readbyte(RTC_ADDR_DAY); break;
- case RTC_DAY_OF_MONTH: val = ds1302_readbyte(RTC_ADDR_DATE); break;
- case RTC_MONTH: val = ds1302_readbyte(RTC_ADDR_MON); break;
- case RTC_YEAR: val = ds1302_readbyte(RTC_ADDR_YEAR); break;
- case RTC_REG_A: /* RTC_FREQ_SELECT */ break;
- case RTC_REG_B: /* RTC_CONTROL */ break;
- case RTC_REG_C: /* RTC_INTR_FLAGS */ break;
- case RTC_REG_D: val = RTC_VRT /* RTC_VALID */; break;
- default: break;
- }
-
- return(val);
-}
-
-void secureedge5410_cmos_write(unsigned char val, int addr)
-{
- if (!use_ds1302) {
- __CMOS_WRITE(val, addr, w);
- return;
- }
-
- switch(addr) {
- case RTC_SECONDS: ds1302_writebyte(RTC_ADDR_SEC, val); break;
- case RTC_SECONDS_ALARM: break;
- case RTC_MINUTES: ds1302_writebyte(RTC_ADDR_MIN, val); break;
- case RTC_MINUTES_ALARM: break;
- case RTC_HOURS: ds1302_writebyte(RTC_ADDR_HOUR, val); break;
- case RTC_HOURS_ALARM: break;
- case RTC_DAY_OF_WEEK: ds1302_writebyte(RTC_ADDR_DAY, val); break;
- case RTC_DAY_OF_MONTH: ds1302_writebyte(RTC_ADDR_DATE, val); break;
- case RTC_MONTH: ds1302_writebyte(RTC_ADDR_MON, val); break;
- case RTC_YEAR: ds1302_writebyte(RTC_ADDR_YEAR, val); break;
- case RTC_REG_A: /* RTC_FREQ_SELECT */ break;
- case RTC_REG_B: /* RTC_CONTROL */ break;
- case RTC_REG_C: /* RTC_INTR_FLAGS */ break;
- case RTC_REG_D: /* RTC_VALID */ break;
- default: break;
- }
-}
diff --git a/arch/sh/boards/snapgear/setup.c b/arch/sh/boards/snapgear/setup.c
index 2b594f6..7022483 100644
--- a/arch/sh/boards/snapgear/setup.c
+++ b/arch/sh/boards/snapgear/setup.c
@@ -22,20 +22,15 @@
#include <asm/snapgear.h>
#include <asm/irq.h>
#include <asm/io.h>
-#include <asm/rtc.h>
#include <asm/cpu/timer.h>
-extern void secureedge5410_rtc_init(void);
-extern void pcibios_init(void);
-
-/****************************************************************************/
/*
* EraseConfig handling functions
*/
static irqreturn_t eraseconfig_interrupt(int irq, void *dev_id)
{
- volatile char dummy __attribute__((unused)) = * (volatile char *) 0xb8000000;
+ (void)ctrl_inb(0xb8000000); /* dummy read */
printk("SnapGear: erase switch interrupt!\n");
@@ -76,19 +71,10 @@
}
/*
- * Initialize the board
- */
-static void __init snapgear_setup(char **cmdline_p)
-{
- board_time_init = secureedge5410_rtc_init;
-}
-
-/*
* The Machine Vector
*/
static struct sh_machine_vector mv_snapgear __initmv = {
.mv_name = "SnapGear SecureEdge5410",
- .mv_setup = snapgear_setup,
.mv_nr_irqs = 72,
.mv_inb = snapgear_inb,
diff --git a/arch/sh/boot/Makefile b/arch/sh/boot/Makefile
index 4c5ffdc..1b0f5be 100644
--- a/arch/sh/boot/Makefile
+++ b/arch/sh/boot/Makefile
@@ -39,7 +39,7 @@
quiet_cmd_uimage = UIMAGE $@
cmd_uimage = $(CONFIG_SHELL) $(MKIMAGE) -A sh -O linux -T kernel \
- -C gzip -a $(KERNEL_LOAD) -e $(KERNEL_LOAD) \
+ -C none -a $(KERNEL_LOAD) -e $(KERNEL_LOAD) \
-n 'Linux-$(KERNELRELEASE)' -d $< $@
$(obj)/uImage: $(obj)/zImage FORCE
diff --git a/arch/sh/cchips/hd6446x/Makefile b/arch/sh/cchips/hd6446x/Makefile
index a106dd9..f7de407 100644
--- a/arch/sh/cchips/hd6446x/Makefile
+++ b/arch/sh/cchips/hd6446x/Makefile
@@ -1,2 +1,4 @@
obj-$(CONFIG_HD64461) += hd64461.o
obj-$(CONFIG_HD64465) += hd64465/
+
+EXTRA_CFLAGS += -Werror
diff --git a/arch/sh/cchips/voyagergx/Makefile b/arch/sh/cchips/voyagergx/Makefile
index 085de72..f73963c 100644
--- a/arch/sh/cchips/voyagergx/Makefile
+++ b/arch/sh/cchips/voyagergx/Makefile
@@ -6,3 +6,4 @@
obj-$(CONFIG_USB_OHCI_HCD) += consistent.o
+EXTRA_CFLAGS += -Werror
diff --git a/arch/sh/drivers/pci/Makefile b/arch/sh/drivers/pci/Makefile
index 2f65ac7..fba6b5b 100644
--- a/arch/sh/drivers/pci/Makefile
+++ b/arch/sh/drivers/pci/Makefile
@@ -5,7 +5,6 @@
obj-y += pci.o
obj-$(CONFIG_PCI_AUTO) += pci-auto.o
-obj-$(CONFIG_CPU_SUBTYPE_ST40STB1) += pci-st40.o
obj-$(CONFIG_CPU_SUBTYPE_SH7751) += pci-sh7751.o ops-sh4.o
obj-$(CONFIG_CPU_SUBTYPE_SH7751R) += pci-sh7751.o ops-sh4.o
obj-$(CONFIG_CPU_SUBTYPE_SH7780) += pci-sh7780.o ops-sh4.o
diff --git a/arch/sh/drivers/pci/pci-st40.c b/arch/sh/drivers/pci/pci-st40.c
deleted file mode 100644
index 0814a5a..0000000
--- a/arch/sh/drivers/pci/pci-st40.c
+++ /dev/null
@@ -1,488 +0,0 @@
-/*
- * Copyright (C) 2001 David J. Mckay (david.mckay@st.com)
- *
- * May be copied or modified under the terms of the GNU General Public
- * License. See linux/COPYING for more information.
- *
- * Support functions for the ST40 PCI hardware.
- */
-
-#include <linux/kernel.h>
-#include <linux/smp.h>
-#include <linux/init.h>
-#include <linux/errno.h>
-#include <linux/pci.h>
-#include <linux/delay.h>
-#include <linux/types.h>
-#include <asm/pci.h>
-#include <linux/irq.h>
-#include <linux/interrupt.h> /* irqreturn_t */
-
-#include "pci-st40.h"
-
-/* This is in P2 of course */
-#define ST40PCI_BASE_ADDRESS (0xb0000000)
-#define ST40PCI_MEM_ADDRESS (ST40PCI_BASE_ADDRESS+0x0)
-#define ST40PCI_IO_ADDRESS (ST40PCI_BASE_ADDRESS+0x06000000)
-#define ST40PCI_REG_ADDRESS (ST40PCI_BASE_ADDRESS+0x07000000)
-
-#define ST40PCI_REG(x) (ST40PCI_REG_ADDRESS+(ST40PCI_##x))
-#define ST40PCI_REG_INDEXED(reg, index) \
- (ST40PCI_REG(reg##0) + \
- ((ST40PCI_REG(reg##1) - ST40PCI_REG(reg##0))*index))
-
-#define ST40PCI_WRITE(reg,val) writel((val),ST40PCI_REG(reg))
-#define ST40PCI_WRITE_SHORT(reg,val) writew((val),ST40PCI_REG(reg))
-#define ST40PCI_WRITE_BYTE(reg,val) writeb((val),ST40PCI_REG(reg))
-#define ST40PCI_WRITE_INDEXED(reg, index, val) \
- writel((val), ST40PCI_REG_INDEXED(reg, index));
-
-#define ST40PCI_READ(reg) readl(ST40PCI_REG(reg))
-#define ST40PCI_READ_SHORT(reg) readw(ST40PCI_REG(reg))
-#define ST40PCI_READ_BYTE(reg) readb(ST40PCI_REG(reg))
-
-#define ST40PCI_SERR_IRQ 64
-#define ST40PCI_ERR_IRQ 65
-
-
-/* Macros to extract PLL params */
-#define PLL_MDIV(reg) ( ((unsigned)reg) & 0xff )
-#define PLL_NDIV(reg) ( (((unsigned)reg)>>8) & 0xff )
-#define PLL_PDIV(reg) ( (((unsigned)reg)>>16) & 0x3 )
-#define PLL_SETUP(reg) ( (((unsigned)reg)>>19) & 0x1ff )
-
-/* Build up the appropriate settings */
-#define PLL_SET(mdiv,ndiv,pdiv,setup) \
-( ((mdiv)&0xff) | (((ndiv)&0xff)<<8) | (((pdiv)&3)<<16)| (((setup)&0x1ff)<<19))
-
-#define PLLPCICR (0xbb040000+0x10)
-
-#define PLLPCICR_POWERON (1<<28)
-#define PLLPCICR_OUT_EN (1<<29)
-#define PLLPCICR_LOCKSELECT (1<<30)
-#define PLLPCICR_LOCK (1<<31)
-
-
-#define PLL_25MHZ 0x793c8512
-#define PLL_33MHZ PLL_SET(18,88,3,295)
-
-static void pci_set_rbar_region(unsigned int region, unsigned long localAddr,
- unsigned long pciOffset, unsigned long regionSize);
-
-static __init void SetPCIPLL(void)
-{
- {
- /* Lets play with the PLL values */
- unsigned long pll1cr1;
- unsigned long mdiv, ndiv, pdiv;
- unsigned long muxcr;
- unsigned int muxcr_ratios[4] = { 8, 16, 21, 1 };
- unsigned int freq;
-
-#define CLKGENA 0xbb040000
-#define CLKGENA_PLL2_MUXCR CLKGENA + 0x48
- pll1cr1 = ctrl_inl(PLLPCICR);
- printk("PLL1CR1 %08lx\n", pll1cr1);
- mdiv = PLL_MDIV(pll1cr1);
- ndiv = PLL_NDIV(pll1cr1);
- pdiv = PLL_PDIV(pll1cr1);
- printk("mdiv %02lx ndiv %02lx pdiv %02lx\n", mdiv, ndiv, pdiv);
- freq = ((2*27*ndiv)/mdiv) / (1 << pdiv);
- printk("PLL freq %dMHz\n", freq);
- muxcr = ctrl_inl(CLKGENA_PLL2_MUXCR);
- printk("PCI freq %dMhz\n", freq / muxcr_ratios[muxcr & 3]);
- }
-}
-
-
-struct pci_err {
- unsigned mask;
- const char *error_string;
-};
-
-static struct pci_err int_error[]={
- { INT_MNLTDIM,"MNLTDIM: Master non-lock transfer"},
- { INT_TTADI, "TTADI: Illegal byte enable in I/O transfer"},
- { INT_TMTO, "TMTO: Target memory read/write timeout"},
- { INT_MDEI, "MDEI: Master function disable error"},
- { INT_APEDI, "APEDI: Address parity error"},
- { INT_SDI, "SDI: SERR detected"},
- { INT_DPEITW, "DPEITW: Data parity error target write"},
- { INT_PEDITR, "PEDITR: PERR detected"},
- { INT_TADIM, "TADIM: Target abort detected"},
- { INT_MADIM, "MADIM: Master abort detected"},
- { INT_MWPDI, "MWPDI: PERR from target at data write"},
- { INT_MRDPEI, "MRDPEI: Master read data parity error"}
-};
-#define NUM_PCI_INT_ERRS ARRAY_SIZE(int_error)
-
-static struct pci_err aint_error[]={
- { AINT_MBI, "MBI: Master broken"},
- { AINT_TBTOI, "TBTOI: Target bus timeout"},
- { AINT_MBTOI, "MBTOI: Master bus timeout"},
- { AINT_TAI, "TAI: Target abort"},
- { AINT_MAI, "MAI: Master abort"},
- { AINT_RDPEI, "RDPEI: Read data parity"},
- { AINT_WDPE, "WDPE: Write data parity"}
-};
-
-#define NUM_PCI_AINT_ERRS ARRAY_SIZE(aint_error)
-
-static void print_pci_errors(unsigned reg,struct pci_err *error,int num_errors)
-{
- int i;
-
- for(i=0;i<num_errors;i++) {
- if(reg & error[i].mask) {
- printk("%s\n",error[i].error_string);
- }
- }
-
-}
-
-
-static char * pci_commands[16]={
- "Int Ack",
- "Special Cycle",
- "I/O Read",
- "I/O Write",
- "Reserved",
- "Reserved",
- "Memory Read",
- "Memory Write",
- "Reserved",
- "Reserved",
- "Configuration Read",
- "Configuration Write",
- "Memory Read Multiple",
- "Dual Address Cycle",
- "Memory Read Line",
- "Memory Write-and-Invalidate"
-};
-
-static irqreturn_t st40_pci_irq(int irq, void *dev_instance)
-{
- unsigned pci_int, pci_air, pci_cir, pci_aint;
- static int count=0;
-
-
- pci_int = ST40PCI_READ(INT);pci_aint = ST40PCI_READ(AINT);
- pci_cir = ST40PCI_READ(CIR);pci_air = ST40PCI_READ(AIR);
-
- /* Reset state to stop multiple interrupts */
- ST40PCI_WRITE(INT, ~0); ST40PCI_WRITE(AINT, ~0);
-
-
- if(++count>1) return IRQ_HANDLED;
-
- printk("** PCI ERROR **\n");
-
- if(pci_int) {
- printk("** INT register status\n");
- print_pci_errors(pci_int,int_error,NUM_PCI_INT_ERRS);
- }
-
- if(pci_aint) {
- printk("** AINT register status\n");
- print_pci_errors(pci_aint,aint_error,NUM_PCI_AINT_ERRS);
- }
-
- printk("** Address and command info\n");
-
- printk("** Command %s : Address 0x%x\n",
- pci_commands[pci_cir&0xf],pci_air);
-
- if(pci_cir&CIR_PIOTEM) {
- printk("CIR_PIOTEM:PIO transfer error for master\n");
- }
- if(pci_cir&CIR_RWTET) {
- printk("CIR_RWTET:Read/Write transfer error for target\n");
- }
-
- return IRQ_HANDLED;
-}
-
-
-/* Rounds a number UP to the nearest power of two. Used for
- * sizing the PCI window.
- */
-static u32 r2p2(u32 num)
-{
- int i = 31;
- u32 tmp = num;
-
- if (num == 0)
- return 0;
-
- do {
- if (tmp & (1 << 31))
- break;
- i--;
- tmp <<= 1;
- } while (i >= 0);
-
- tmp = 1 << i;
- /* If the original number isn't a power of 2, round it up */
- if (tmp != num)
- tmp <<= 1;
-
- return tmp;
-}
-
-static void __init pci_fixup_ide_bases(struct pci_dev *d)
-{
- int i;
-
- /*
- * PCI IDE controllers use non-standard I/O port decoding, respect it.
- */
- if ((d->class >> 8) != PCI_CLASS_STORAGE_IDE)
- return;
- printk("PCI: IDE base address fixup for %s\n", pci_name(d));
- for(i=0; i<4; i++) {
- struct resource *r = &d->resource[i];
- if ((r->start & ~0x80) == 0x374) {
- r->start |= 2;
- r->end = r->start;
- }
- }
-}
-DECLARE_PCI_FIXUP_HEADER(PCI_ANY_ID, PCI_ANY_ID, pci_fixup_ide_bases);
-
-int __init st40pci_init(unsigned memStart, unsigned memSize)
-{
- u32 lsr0;
-
- SetPCIPLL();
-
- /* Initialises the ST40 pci subsystem, performing a reset, then programming
- * up the address space decoders appropriately
- */
-
- /* Should reset core here as well methink */
-
- ST40PCI_WRITE(CR, CR_LOCK_MASK | CR_SOFT_RESET);
-
- /* Loop while core resets */
- while (ST40PCI_READ(CR) & CR_SOFT_RESET);
-
- /* Switch off interrupts */
- ST40PCI_WRITE(INTM, 0);
- ST40PCI_WRITE(AINT, 0);
-
- /* Now, lets reset all the cards on the bus with extreme prejudice */
- ST40PCI_WRITE(CR, CR_LOCK_MASK | CR_RSTCTL);
- udelay(250);
-
- /* Set bus active, take it out of reset */
- ST40PCI_WRITE(CR, CR_LOCK_MASK | CR_BMAM | CR_CFINT | CR_PFCS | CR_PFE);
-
- /* The PCI spec says that no access must be made to the bus until 1 second
- * after reset. This seem ludicrously long, but some delay is needed here
- */
- mdelay(1000);
-
- /* Switch off interrupts */
- ST40PCI_WRITE(INTM, 0);
- ST40PCI_WRITE(AINT, 0);
-
- /* Allow it to be a master */
-
- ST40PCI_WRITE_SHORT(CSR_CMD,
- PCI_COMMAND_MEMORY | PCI_COMMAND_MASTER |
- PCI_COMMAND_IO);
-
- /* Access to the 0xb0000000 -> 0xb6000000 area will go through to 0x10000000 -> 0x16000000
- * on the PCI bus. This allows a nice 1-1 bus to phys mapping.
- */
-
-
- ST40PCI_WRITE(MBR, 0x10000000);
- /* Always set the max size 128M (actually, it is only 96MB wide) */
- ST40PCI_WRITE(MBMR, 0x07ff0000);
-
- /* I/O addresses are mapped at 0xb6000000 -> 0xb7000000. These are changed to 0, to
- * allow cards that have legacy io such as vga to function correctly. This gives a
- * maximum of 64K of io/space as only the bottom 16 bits of the address are copied
- * over to the bus when the transaction is made. 64K of io space is more than enough
- */
- ST40PCI_WRITE(IOBR, 0x0);
- /* Set up the 64K window */
- ST40PCI_WRITE(IOBMR, 0x0);
-
- /* Now we set up the mbars so the PCI bus can see the local memory */
- /* Expose a 256M window starting at PCI address 0... */
- ST40PCI_WRITE(CSR_MBAR0, 0);
- ST40PCI_WRITE(LSR0, 0x0fff0001);
-
- /* ... and set up the initial incoming window to expose all of RAM */
- pci_set_rbar_region(7, memStart, memStart, memSize);
-
- /* Maximise timeout values */
- ST40PCI_WRITE_BYTE(CSR_TRDY, 0xff);
- ST40PCI_WRITE_BYTE(CSR_RETRY, 0xff);
- ST40PCI_WRITE_BYTE(CSR_MIT, 0xff);
-
- ST40PCI_WRITE_BYTE(PERF,PERF_MASTER_WRITE_POSTING);
-
- return 1;
-}
-
-char * __devinit pcibios_setup(char *str)
-{
- return str;
-}
-
-
-#define SET_CONFIG_BITS(bus,devfn,where)\
- (((bus) << 16) | ((devfn) << 8) | ((where) & ~3) | (bus!=0))
-
-#define CONFIG_CMD(bus, devfn, where) SET_CONFIG_BITS(bus->number,devfn,where)
-
-
-static int CheckForMasterAbort(void)
-{
- if (ST40PCI_READ(INT) & INT_MADIM) {
- /* Should we clear config space version as well ??? */
- ST40PCI_WRITE(INT, INT_MADIM);
- ST40PCI_WRITE_SHORT(CSR_STATUS, 0);
- return 1;
- }
-
- return 0;
-}
-
-/* Write to config register */
-static int st40pci_read(struct pci_bus *bus, unsigned int devfn, int where, int size, u32 * val)
-{
- ST40PCI_WRITE(PAR, CONFIG_CMD(bus, devfn, where));
- switch (size) {
- case 1:
- *val = (u8)ST40PCI_READ_BYTE(PDR + (where & 3));
- break;
- case 2:
- *val = (u16)ST40PCI_READ_SHORT(PDR + (where & 2));
- break;
- case 4:
- *val = ST40PCI_READ(PDR);
- break;
- }
-
- if (CheckForMasterAbort()){
- switch (size) {
- case 1:
- *val = (u8)0xff;
- break;
- case 2:
- *val = (u16)0xffff;
- break;
- case 4:
- *val = 0xffffffff;
- break;
- }
- }
-
- return PCIBIOS_SUCCESSFUL;
-}
-
-static int st40pci_write(struct pci_bus *bus, unsigned int devfn, int where, int size, u32 val)
-{
- ST40PCI_WRITE(PAR, CONFIG_CMD(bus, devfn, where));
-
- switch (size) {
- case 1:
- ST40PCI_WRITE_BYTE(PDR + (where & 3), (u8)val);
- break;
- case 2:
- ST40PCI_WRITE_SHORT(PDR + (where & 2), (u16)val);
- break;
- case 4:
- ST40PCI_WRITE(PDR, val);
- break;
- }
-
- CheckForMasterAbort();
-
- return PCIBIOS_SUCCESSFUL;
-}
-
-struct pci_ops st40pci_config_ops = {
- .read = st40pci_read,
- .write = st40pci_write,
-};
-
-
-/* Everything hangs off this */
-static struct pci_bus *pci_root_bus;
-
-static int __init pcibios_init(void)
-{
- extern unsigned long memory_start, memory_end;
-
- printk(KERN_ALERT "pci-st40.c: pcibios_init\n");
-
- if (sh_mv.mv_init_pci != NULL) {
- sh_mv.mv_init_pci();
- }
-
- /* The pci subsytem needs to know where memory is and how much
- * of it there is. I've simply made these globals. A better mechanism
- * is probably needed.
- */
- st40pci_init(PHYSADDR(memory_start),
- PHYSADDR(memory_end) - PHYSADDR(memory_start));
-
- if (request_irq(ST40PCI_ERR_IRQ, st40_pci_irq,
- IRQF_DISABLED, "st40pci", NULL)) {
- printk(KERN_ERR "st40pci: Cannot hook interrupt\n");
- return -EIO;
- }
-
- /* Enable the PCI interrupts on the device */
- ST40PCI_WRITE(INTM, ~0);
- ST40PCI_WRITE(AINT, ~0);
-
- /* Map the io address apprioately */
-#ifdef CONFIG_HD64465
- hd64465_port_map(PCIBIOS_MIN_IO, (64 * 1024) - PCIBIOS_MIN_IO + 1,
- ST40_IO_ADDR + PCIBIOS_MIN_IO, 0);
-#endif
-
- /* ok, do the scan man */
- pci_root_bus = pci_scan_bus(0, &st40pci_config_ops, NULL);
- pci_assign_unassigned_resources();
-
- return 0;
-}
-subsys_initcall(pcibios_init);
-
-/*
- * Publish a region of local address space over the PCI bus
- * to other devices.
- */
-static void pci_set_rbar_region(unsigned int region, unsigned long localAddr,
- unsigned long pciOffset, unsigned long regionSize)
-{
- unsigned long mask;
-
- if (region > 7)
- return;
-
- if (regionSize > (512 * 1024 * 1024))
- return;
-
- mask = r2p2(regionSize) - 0x10000;
-
- /* Disable the region (in case currently in use, should never happen) */
- ST40PCI_WRITE_INDEXED(RSR, region, 0);
-
- /* Start of local address space to publish */
- ST40PCI_WRITE_INDEXED(RLAR, region, PHYSADDR(localAddr) );
-
- /* Start of region in PCI address space as an offset from MBAR0 */
- ST40PCI_WRITE_INDEXED(RBAR, region, pciOffset);
-
- /* Size of region */
- ST40PCI_WRITE_INDEXED(RSR, region, mask | 1);
-}
-
diff --git a/arch/sh/drivers/pci/pci-st40.h b/arch/sh/drivers/pci/pci-st40.h
deleted file mode 100644
index cf0d35b..0000000
--- a/arch/sh/drivers/pci/pci-st40.h
+++ /dev/null
@@ -1,136 +0,0 @@
-/*
- * Copyright (C) 2001 David J. Mckay (david.mckay@st.com)
- *
- * May be copied or modified under the terms of the GNU General Public
- * License. See linux/COPYING for more information.
- *
- * Definitions for the ST40 PCI hardware.
- */
-
-#ifndef __PCI_ST40_H__
-#define __PCI_ST40_H__
-
-#define ST40PCI_VCR_STATUS 0x00
-
-#define ST40PCI_VCR_VERSION 0x08
-
-#define ST40PCI_CR 0x10
-
-#define CR_SOFT_RESET (1<<12)
-#define CR_PFCS (1<<11)
-#define CR_PFE (1<<9)
-#define CR_BMAM (1<<6)
-#define CR_HOST (1<<5)
-#define CR_CLKEN (1<<4)
-#define CR_SOCS (1<<3)
-#define CR_IOCS (1<<2)
-#define CR_RSTCTL (1<<1)
-#define CR_CFINT (1<<0)
-#define CR_LOCK_MASK 0x5a000000
-
-
-#define ST40PCI_LSR0 0X14
-#define ST40PCI_LAR0 0x1c
-
-#define ST40PCI_INT 0x24
-#define INT_MNLTDIM (1<<15)
-#define INT_TTADI (1<<14)
-#define INT_TMTO (1<<9)
-#define INT_MDEI (1<<8)
-#define INT_APEDI (1<<7)
-#define INT_SDI (1<<6)
-#define INT_DPEITW (1<<5)
-#define INT_PEDITR (1<<4)
-#define INT_TADIM (1<<3)
-#define INT_MADIM (1<<2)
-#define INT_MWPDI (1<<1)
-#define INT_MRDPEI (1<<0)
-
-
-#define ST40PCI_INTM 0x28
-#define ST40PCI_AIR 0x2c
-
-#define ST40PCI_CIR 0x30
-#define CIR_PIOTEM (1<<31)
-#define CIR_RWTET (1<<26)
-
-#define ST40PCI_AINT 0x40
-#define AINT_MBI (1<<13)
-#define AINT_TBTOI (1<<12)
-#define AINT_MBTOI (1<<11)
-#define AINT_TAI (1<<3)
-#define AINT_MAI (1<<2)
-#define AINT_RDPEI (1<<1)
-#define AINT_WDPE (1<<0)
-
-#define ST40PCI_AINTM 0x44
-#define ST40PCI_BMIR 0x48
-#define ST40PCI_PAR 0x4c
-#define ST40PCI_MBR 0x50
-#define ST40PCI_IOBR 0x54
-#define ST40PCI_PINT 0x58
-#define ST40PCI_PINTM 0x5c
-#define ST40PCI_MBMR 0x70
-#define ST40PCI_IOBMR 0x74
-#define ST40PCI_PDR 0x78
-
-/* H8 specific registers start here */
-#define ST40PCI_WCBAR 0x7c
-#define ST40PCI_LOCCFG_UNLOCK 0x34
-
-#define ST40PCI_RBAR0 0x100
-#define ST40PCI_RSR0 0x104
-#define ST40PCI_RLAR0 0x108
-
-#define ST40PCI_RBAR1 0x110
-#define ST40PCI_RSR1 0x114
-#define ST40PCI_RLAR1 0x118
-
-
-#define ST40PCI_RBAR2 0x120
-#define ST40PCI_RSR2 0x124
-#define ST40PCI_RLAR2 0x128
-
-#define ST40PCI_RBAR3 0x130
-#define ST40PCI_RSR3 0x134
-#define ST40PCI_RLAR3 0x138
-
-#define ST40PCI_RBAR4 0x140
-#define ST40PCI_RSR4 0x144
-#define ST40PCI_RLAR4 0x148
-
-#define ST40PCI_RBAR5 0x150
-#define ST40PCI_RSR5 0x154
-#define ST40PCI_RLAR5 0x158
-
-#define ST40PCI_RBAR6 0x160
-#define ST40PCI_RSR6 0x164
-#define ST40PCI_RLAR6 0x168
-
-#define ST40PCI_RBAR7 0x170
-#define ST40PCI_RSR7 0x174
-#define ST40PCI_RLAR7 0x178
-
-
-#define ST40PCI_RBAR(n) (0x100+(0x10*(n)))
-#define ST40PCI_RSR(n) (0x104+(0x10*(n)))
-#define ST40PCI_RLAR(n) (0x108+(0x10*(n)))
-
-#define ST40PCI_PERF 0x80
-#define PERF_MASTER_WRITE_POSTING (1<<4)
-/* H8 specific registers end here */
-
-
-/* These are configs space registers */
-#define ST40PCI_CSR_VID 0x10000
-#define ST40PCI_CSR_DID 0x10002
-#define ST40PCI_CSR_CMD 0x10004
-#define ST40PCI_CSR_STATUS 0x10006
-#define ST40PCI_CSR_MBAR0 0x10010
-#define ST40PCI_CSR_TRDY 0x10040
-#define ST40PCI_CSR_RETRY 0x10041
-#define ST40PCI_CSR_MIT 0x1000d
-
-#define ST40_IO_ADDR 0xb6000000
-
-#endif /* __PCI_ST40_H__ */
diff --git a/arch/sh/kernel/Makefile b/arch/sh/kernel/Makefile
index 1f141a8..4b81d9c 100644
--- a/arch/sh/kernel/Makefile
+++ b/arch/sh/kernel/Makefile
@@ -10,7 +10,6 @@
obj-y += cpu/ timers/
obj-$(CONFIG_VSYSCALL) += vsyscall/
-
obj-$(CONFIG_SMP) += smp.o
obj-$(CONFIG_CF_ENABLER) += cf-enabler.o
obj-$(CONFIG_SH_STANDARD_BIOS) += sh_bios.o
@@ -22,3 +21,5 @@
obj-$(CONFIG_CRASH_DUMP) += crash_dump.o
obj-$(CONFIG_PM) += pm.o
obj-$(CONFIG_STACKTRACE) += stacktrace.o
+
+EXTRA_CFLAGS += -Werror
diff --git a/arch/sh/kernel/cpu/sh3/ex.S b/arch/sh/kernel/cpu/sh3/ex.S
index 2b2a9e0..b6abf38 100644
--- a/arch/sh/kernel/cpu/sh3/ex.S
+++ b/arch/sh/kernel/cpu/sh3/ex.S
@@ -46,7 +46,7 @@
.long exception_error ! illegal_slot_instruction (filled by trap_init) /*1A0*/
ENTRY(nmi_slot)
#if defined (CONFIG_KGDB_NMI)
- .long debug_enter /* 1C0 */ ! Allow trap to debugger
+ .long kgdb_handle_exception /* 1C0 */ ! Allow trap to debugger
#else
.long exception_none /* 1C0 */ ! Not implemented yet
#endif
diff --git a/arch/sh/kernel/cpu/sh4/probe.c b/arch/sh/kernel/cpu/sh4/probe.c
index 21375d7..bc9c28a 100644
--- a/arch/sh/kernel/cpu/sh4/probe.c
+++ b/arch/sh/kernel/cpu/sh4/probe.c
@@ -139,14 +139,6 @@
boot_cpu_data.flags |= CPU_HAS_FPU | CPU_HAS_PERF_COUNTER |
CPU_HAS_LLSC;
break;
- case 0x8000:
- boot_cpu_data.type = CPU_ST40RA;
- boot_cpu_data.flags |= CPU_HAS_FPU;
- break;
- case 0x8100:
- boot_cpu_data.type = CPU_ST40GX1;
- boot_cpu_data.flags |= CPU_HAS_FPU;
- break;
case 0x700:
boot_cpu_data.type = CPU_SH4_501;
boot_cpu_data.icache.ways = 2;
diff --git a/arch/sh/kernel/irq.c b/arch/sh/kernel/irq.c
index 348da19..0586bc6 100644
--- a/arch/sh/kernel/irq.c
+++ b/arch/sh/kernel/irq.c
@@ -11,7 +11,6 @@
#include <linux/module.h>
#include <linux/kernel_stat.h>
#include <linux/seq_file.h>
-#include <linux/irq.h>
#include <asm/processor.h>
#include <asm/machvec.h>
#include <asm/uaccess.h>
diff --git a/arch/sh/kernel/kgdb_stub.c b/arch/sh/kernel/kgdb_stub.c
index 2fdc700..d453c3a 100644
--- a/arch/sh/kernel/kgdb_stub.c
+++ b/arch/sh/kernel/kgdb_stub.c
@@ -102,6 +102,7 @@
#include <linux/init.h>
#include <linux/console.h>
#include <linux/sysrq.h>
+#include <linux/module.h>
#include <asm/system.h>
#include <asm/cacheflush.h>
#include <asm/current.h>
@@ -116,7 +117,9 @@
kgdb_bus_error_hook_t *kgdb_bus_err_hook;
int (*kgdb_getchar)(void);
+EXPORT_SYMBOL_GPL(kgdb_getchar);
void (*kgdb_putchar)(int);
+EXPORT_SYMBOL_GPL(kgdb_putchar);
static void put_debug_char(int c)
{
@@ -136,7 +139,7 @@
#define NUMREGBYTES (MAXREG*4)
#define OUTBUFMAX (NUMREGBYTES*2+512)
-enum regs {
+enum {
R0 = 0, R1, R2, R3, R4, R5, R6, R7,
R8, R9, R10, R11, R12, R13, R14, R15,
PC, PR, GBR, VBR, MACH, MACL, SR,
@@ -176,9 +179,13 @@
/* SCI/UART settings, used in kgdb_console_setup() */
int kgdb_portnum = CONFIG_KGDB_DEFPORT;
+EXPORT_SYMBOL_GPL(kgdb_portnum);
int kgdb_baud = CONFIG_KGDB_DEFBAUD;
+EXPORT_SYMBOL_GPL(kgdb_baud);
char kgdb_parity = CONFIG_KGDB_DEFPARITY;
+EXPORT_SYMBOL_GPL(kgdb_parity);
char kgdb_bits = CONFIG_KGDB_DEFBITS;
+EXPORT_SYMBOL_GPL(kgdb_bits);
/* Jump buffer for setjmp/longjmp */
static jmp_buf rem_com_env;
diff --git a/arch/sh/kernel/setup.c b/arch/sh/kernel/setup.c
index 0b8c45d..4156aac 100644
--- a/arch/sh/kernel/setup.c
+++ b/arch/sh/kernel/setup.c
@@ -303,7 +303,6 @@
[CPU_SH7750S] = "SH7750S", [CPU_SH7750R] = "SH7750R",
[CPU_SH7751] = "SH7751", [CPU_SH7751R] = "SH7751R",
[CPU_SH7760] = "SH7760",
- [CPU_ST40RA] = "ST40RA", [CPU_ST40GX1] = "ST40GX1",
[CPU_SH4_202] = "SH4-202", [CPU_SH4_501] = "SH4-501",
[CPU_SH7770] = "SH7770", [CPU_SH7780] = "SH7780",
[CPU_SH7781] = "SH7781", [CPU_SH7343] = "SH7343",
diff --git a/arch/sh/kernel/sh_ksyms.c b/arch/sh/kernel/sh_ksyms.c
index 548e428..e1a6de9 100644
--- a/arch/sh/kernel/sh_ksyms.c
+++ b/arch/sh/kernel/sh_ksyms.c
@@ -106,7 +106,6 @@
DECLARE_EXPORT(__movstr);
#endif
-#ifdef CONFIG_CPU_SH4
#if __GNUC__ == 4
DECLARE_EXPORT(__movmem_i4_even);
DECLARE_EXPORT(__movmem_i4_odd);
@@ -126,7 +125,6 @@
DECLARE_EXPORT(__movstr_i4_odd);
DECLARE_EXPORT(__movstrSI12_i4);
#endif /* __GNUC__ == 4 */
-#endif
#if !defined(CONFIG_CACHE_OFF) && (defined(CONFIG_CPU_SH4) || \
defined(CONFIG_SH7705_CACHE_32KB))
diff --git a/arch/sh/lib/Makefile b/arch/sh/lib/Makefile
index e23dd1a..9dc7b69 100644
--- a/arch/sh/lib/Makefile
+++ b/arch/sh/lib/Makefile
@@ -9,3 +9,5 @@
memcpy-$(CONFIG_CPU_SH4) := memcpy-sh4.o
lib-y += $(memcpy-y)
+
+EXTRA_CFLAGS += -Werror
diff --git a/arch/sh/mm/Kconfig b/arch/sh/mm/Kconfig
index cf446bb..1265f20 100644
--- a/arch/sh/mm/Kconfig
+++ b/arch/sh/mm/Kconfig
@@ -17,7 +17,7 @@
bool
select CPU_HAS_INTEVT
select CPU_HAS_SR_RB
- select CPU_HAS_PTEA if (!CPU_SUBTYPE_ST40 && !CPU_SH4A) || CPU_SHX2
+ select CPU_HAS_PTEA if !CPU_SH4A || CPU_SHX2
select CPU_HAS_FPU if !CPU_SH4AL_DSP
config CPU_SH4A
@@ -29,10 +29,6 @@
select CPU_SH4A
select CPU_HAS_DSP
-config CPU_SUBTYPE_ST40
- bool
- select CPU_SH4
-
config CPU_SHX2
bool
@@ -152,21 +148,6 @@
bool "Support SH4-202 processor"
select CPU_SH4
-# ST40 Processor Support
-
-config CPU_SUBTYPE_ST40STB1
- bool "Support ST40STB1/ST40RA processors"
- select CPU_SUBTYPE_ST40
- help
- Select ST40STB1 if you have a ST40RA CPU.
- This was previously called the ST40STB1, hence the option name.
-
-config CPU_SUBTYPE_ST40GX1
- bool "Support ST40GX1 processor"
- select CPU_SUBTYPE_ST40
- help
- Select ST40GX1 if you have a ST40GX1 CPU.
-
# SH-4A Processor Support
config CPU_SUBTYPE_SH7770
diff --git a/arch/sh/mm/Makefile b/arch/sh/mm/Makefile
index ee30fb4..aa44607 100644
--- a/arch/sh/mm/Makefile
+++ b/arch/sh/mm/Makefile
@@ -33,3 +33,5 @@
obj-$(CONFIG_HUGETLB_PAGE) += hugetlbpage.o
obj-$(CONFIG_32BIT) += pmb.o
obj-$(CONFIG_NUMA) += numa.o
+
+EXTRA_CFLAGS += -Werror
diff --git a/arch/sh/mm/clear_page.S b/arch/sh/mm/clear_page.S
index 8a70613..7a7c81e 100644
--- a/arch/sh/mm/clear_page.S
+++ b/arch/sh/mm/clear_page.S
@@ -150,48 +150,3 @@
.long 8b, .Lbad_clear_user
.long 9b, .Lbad_clear_user
.previous
-
-#if defined(CONFIG_CPU_SH4)
-/*
- * __clear_user_page
- * @to: P3 address (with same color)
- * @orig_to: P1 address
- *
- * void __clear_user_page(void *to, void *orig_to)
- */
-
-/*
- * r0 --- scratch
- * r4 --- to
- * r5 --- orig_to
- * r6 --- to + PAGE_SIZE
- */
-ENTRY(__clear_user_page)
- mov.l .Lpsz,r0
- mov r4,r6
- add r0,r6
- mov #0,r0
- !
-1: ocbi @r5
- add #32,r5
- movca.l r0,@r4
- mov r4,r1
- add #32,r4
- mov.l r0,@-r4
- mov.l r0,@-r4
- mov.l r0,@-r4
- mov.l r0,@-r4
- mov.l r0,@-r4
- mov.l r0,@-r4
- mov.l r0,@-r4
- add #28,r4
- cmp/eq r6,r4
- bf/s 1b
- ocbwb @r1
- !
- rts
- nop
-.Lpsz: .long PAGE_SIZE
-
-#endif
-
diff --git a/arch/sh/mm/copy_page.S b/arch/sh/mm/copy_page.S
index 3d8409d..4068501 100644
--- a/arch/sh/mm/copy_page.S
+++ b/arch/sh/mm/copy_page.S
@@ -68,67 +68,6 @@
rts
nop
-#if defined(CONFIG_CPU_SH4)
-/*
- * __copy_user_page
- * @to: P1 address (with same color)
- * @from: P1 address
- * @orig_to: P1 address
- *
- * void __copy_user_page(void *to, void *from, void *orig_to)
- */
-
-/*
- * r0, r1, r2, r3, r4, r5, r6, r7 --- scratch
- * r8 --- from + PAGE_SIZE
- * r9 --- orig_to
- * r10 --- to
- * r11 --- from
- */
-ENTRY(__copy_user_page)
- mov.l r8,@-r15
- mov.l r9,@-r15
- mov.l r10,@-r15
- mov.l r11,@-r15
- mov r4,r10
- mov r5,r11
- mov r6,r9
- mov r5,r8
- mov.l .Lpsz,r0
- add r0,r8
- !
-1: ocbi @r9
- add #32,r9
- mov.l @r11+,r0
- mov.l @r11+,r1
- mov.l @r11+,r2
- mov.l @r11+,r3
- mov.l @r11+,r4
- mov.l @r11+,r5
- mov.l @r11+,r6
- mov.l @r11+,r7
- movca.l r0,@r10
- mov r10,r0
- add #32,r10
- mov.l r7,@-r10
- mov.l r6,@-r10
- mov.l r5,@-r10
- mov.l r4,@-r10
- mov.l r3,@-r10
- mov.l r2,@-r10
- mov.l r1,@-r10
- ocbwb @r0
- cmp/eq r11,r8
- bf/s 1b
- add #28,r10
- !
- mov.l @r15+,r11
- mov.l @r15+,r10
- mov.l @r15+,r9
- mov.l @r15+,r8
- rts
- nop
-#endif
.align 2
.Lpsz: .long PAGE_SIZE
/*
diff --git a/arch/sh/mm/pg-sh4.c b/arch/sh/mm/pg-sh4.c
index 25f5c6f..8c7a9ca 100644
--- a/arch/sh/mm/pg-sh4.c
+++ b/arch/sh/mm/pg-sh4.c
@@ -9,6 +9,8 @@
#include <linux/mm.h>
#include <linux/mutex.h>
#include <linux/fs.h>
+#include <linux/highmem.h>
+#include <linux/module.h>
#include <asm/mmu_context.h>
#include <asm/cacheflush.h>
@@ -50,35 +52,62 @@
void clear_user_page(void *to, unsigned long address, struct page *page)
{
__set_bit(PG_mapped, &page->flags);
- if (((address ^ (unsigned long)to) & CACHE_ALIAS) == 0)
- clear_page(to);
- else {
- void *vto = kmap_coherent(page, address);
- __clear_user_page(vto, to);
- kunmap_coherent(vto);
- }
+
+ clear_page(to);
+ if ((((address & PAGE_MASK) ^ (unsigned long)to) & CACHE_ALIAS))
+ __flush_wback_region(to, PAGE_SIZE);
}
-/*
- * copy_user_page
- * @to: P1 address
- * @from: P1 address
- * @address: U0 address to be mapped
- * @page: page (virt_to_page(to))
- */
-void copy_user_page(void *to, void *from, unsigned long address,
- struct page *page)
+void copy_to_user_page(struct vm_area_struct *vma, struct page *page,
+ unsigned long vaddr, void *dst, const void *src,
+ unsigned long len)
{
+ void *vto;
+
__set_bit(PG_mapped, &page->flags);
- if (((address ^ (unsigned long)to) & CACHE_ALIAS) == 0)
- copy_page(to, from);
- else {
- void *vfrom = kmap_coherent(page, address);
- __copy_user_page(vfrom, from, to);
- kunmap_coherent(vfrom);
- }
+
+ vto = kmap_coherent(page, vaddr) + (vaddr & ~PAGE_MASK);
+ memcpy(vto, src, len);
+ kunmap_coherent(vto);
+
+ if (vma->vm_flags & VM_EXEC)
+ flush_cache_page(vma, vaddr, page_to_pfn(page));
}
+void copy_from_user_page(struct vm_area_struct *vma, struct page *page,
+ unsigned long vaddr, void *dst, const void *src,
+ unsigned long len)
+{
+ void *vfrom;
+
+ __set_bit(PG_mapped, &page->flags);
+
+ vfrom = kmap_coherent(page, vaddr) + (vaddr & ~PAGE_MASK);
+ memcpy(dst, vfrom, len);
+ kunmap_coherent(vfrom);
+}
+
+void copy_user_highpage(struct page *to, struct page *from,
+ unsigned long vaddr, struct vm_area_struct *vma)
+{
+ void *vfrom, *vto;
+
+ __set_bit(PG_mapped, &to->flags);
+
+ vto = kmap_atomic(to, KM_USER1);
+ vfrom = kmap_coherent(from, vaddr);
+ copy_page(vto, vfrom);
+ kunmap_coherent(vfrom);
+
+ if (((vaddr ^ (unsigned long)vto) & CACHE_ALIAS))
+ __flush_wback_region(vto, PAGE_SIZE);
+
+ kunmap_atomic(vto, KM_USER1);
+ /* Make sure this page is cleared on other CPU's too before using it */
+ smp_wmb();
+}
+EXPORT_SYMBOL(copy_user_highpage);
+
/*
* For SH-4, we have our own implementation for ptep_get_and_clear
*/
diff --git a/arch/sh/oprofile/Makefile b/arch/sh/oprofile/Makefile
index 1f25d9b..2efc2e7 100644
--- a/arch/sh/oprofile/Makefile
+++ b/arch/sh/oprofile/Makefile
@@ -15,3 +15,4 @@
oprofile-y := $(DRIVER_OBJS) $(profdrvr-y)
+EXTRA_CFLAGS += -Werror
diff --git a/arch/sh64/kernel/process.c b/arch/sh64/kernel/process.c
index ceb9458..0761af4 100644
--- a/arch/sh64/kernel/process.c
+++ b/arch/sh64/kernel/process.c
@@ -26,6 +26,7 @@
#include <linux/reboot.h>
#include <linux/init.h>
#include <linux/module.h>
+#include <linux/proc_fs.h>
#include <asm/uaccess.h>
#include <asm/pgtable.h>
@@ -656,9 +657,6 @@
*/
#if defined(CONFIG_SH64_PROC_ASIDS)
-#include <linux/init.h>
-#include <linux/proc_fs.h>
-
static int
asids_proc_info(char *buf, char **start, off_t fpos, int length, int *eof, void *data)
{
@@ -686,10 +684,8 @@
static int __init register_proc_asids(void)
{
- create_proc_read_entry("asids", 0, NULL, asids_proc_info, NULL);
- return 0;
+ create_proc_read_entry("asids", 0, NULL, asids_proc_info, NULL);
+ return 0;
}
-
__initcall(register_proc_asids);
#endif
-
diff --git a/arch/sh64/kernel/traps.c b/arch/sh64/kernel/traps.c
index c03101f..f32df38 100644
--- a/arch/sh64/kernel/traps.c
+++ b/arch/sh64/kernel/traps.c
@@ -30,7 +30,6 @@
#include <linux/interrupt.h>
#include <linux/sysctl.h>
#include <linux/module.h>
-
#include <asm/system.h>
#include <asm/uaccess.h>
#include <asm/io.h>
@@ -242,9 +241,6 @@
#endif /* CONFIG_SH64_ID2815_WORKAROUND */
-
-#include <asm/system.h>
-
/* Called with interrupts disabled */
asmlinkage void do_exception_error(unsigned long ex, struct pt_regs *regs)
{
@@ -984,4 +980,3 @@
/* Clear all DEBUGINT causes */
poke_real_address_q(DM_EXP_CAUSE_PHY, 0x0);
}
-
diff --git a/drivers/rtc/rtc-sh.c b/drivers/rtc/rtc-sh.c
index 78277a1..8e8c8b8 100644
--- a/drivers/rtc/rtc-sh.c
+++ b/drivers/rtc/rtc-sh.c
@@ -351,8 +351,10 @@
tm->tm_sec, tm->tm_min, tm->tm_hour,
tm->tm_mday, tm->tm_mon + 1, tm->tm_year, tm->tm_wday);
- if (rtc_valid_tm(tm) < 0)
+ if (rtc_valid_tm(tm) < 0) {
dev_err(dev, "invalid date\n");
+ rtc_time_to_tm(0, tm);
+ }
return 0;
}
@@ -588,7 +590,7 @@
rtc->rtc_dev = rtc_device_register("sh", &pdev->dev,
&sh_rtc_ops, THIS_MODULE);
- if (IS_ERR(rtc)) {
+ if (IS_ERR(rtc->rtc_dev)) {
ret = PTR_ERR(rtc->rtc_dev);
goto err_badmap;
}
diff --git a/drivers/serial/sh-sci.h b/drivers/serial/sh-sci.h
index e89ae29..d24621c 100644
--- a/drivers/serial/sh-sci.h
+++ b/drivers/serial/sh-sci.h
@@ -77,7 +77,6 @@
# define SCIF_ONLY
#elif defined(CONFIG_CPU_SUBTYPE_SH7710) || defined(CONFIG_CPU_SUBTYPE_SH7712)
# define SCSPTR0 0xA4400000 /* 16 bit SCIF */
-# define SCI_NPORTS 2
# define SCIF_ORER 0x0001 /* overrun error bit */
# define PACR 0xa4050100
# define PBCR 0xa4050102
@@ -102,12 +101,6 @@
# define SCIF_ORER 0x0001 /* overrun error bit */
# define SCSCR_INIT(port) 0x38 /* TIE=0,RIE=0,TE=1,RE=1,REIE=1 */
# define SCIF_ONLY
-#elif defined(CONFIG_CPU_SUBTYPE_ST40STB1)
-# define SCSPTR1 0xffe00020 /* 16 bit SCIF */
-# define SCSPTR2 0xffe80020 /* 16 bit SCIF */
-# define SCIF_ORER 0x0001 /* overrun error bit */
-# define SCSCR_INIT(port) 0x38 /* TIE=0,RIE=0,TE=1,RE=1,REIE=1 */
-# define SCIF_ONLY
#elif defined(CONFIG_CPU_SUBTYPE_SH5_101) || defined(CONFIG_CPU_SUBTYPE_SH5_103)
# include <asm/hardware.h>
# define SCIF_BASE_ADDR 0x01030000
@@ -116,8 +109,7 @@
# define SCIF_LSR2_OFFS 0x0000024
# define SCSPTR2 ((port->mapbase)+SCIF_PTR2_OFFS) /* 16 bit SCIF */
# define SCLSR2 ((port->mapbase)+SCIF_LSR2_OFFS) /* 16 bit SCIF */
-# define SCSCR_INIT(port) 0x38 /* TIE=0,RIE=0,
- TE=1,RE=1,REIE=1 */
+# define SCSCR_INIT(port) 0x38 /* TIE=0,RIE=0, TE=1,RE=1,REIE=1 */
# define SCIF_ONLY
#elif defined(CONFIG_H83007) || defined(CONFIG_H83068)
# define SCSCR_INIT(port) 0x30 /* TIE=0,RIE=0,TE=1,RE=1 */
@@ -577,15 +569,6 @@
return ctrl_inb(SCPDR0) & 0x0001 ? 1 : 0; /* SCIF0 */
return 1;
}
-#elif defined(CONFIG_CPU_SUBTYPE_ST40STB1)
-static inline int sci_rxd_in(struct uart_port *port)
-{
- if (port->mapbase == 0xffe00000)
- return ctrl_inw(SCSPTR1)&0x0001 ? 1 : 0; /* SCIF */
- else
- return ctrl_inw(SCSPTR2)&0x0001 ? 1 : 0; /* SCIF */
-
-}
#elif defined(CONFIG_CPU_SUBTYPE_SH5_101) || defined(CONFIG_CPU_SUBTYPE_SH5_103)
static inline int sci_rxd_in(struct uart_port *port)
{
diff --git a/drivers/sh/superhyway/superhyway.c b/drivers/sh/superhyway/superhyway.c
index 7d873b3..4d0282b 100644
--- a/drivers/sh/superhyway/superhyway.c
+++ b/drivers/sh/superhyway/superhyway.c
@@ -107,16 +107,17 @@
static int __init superhyway_init(void)
{
struct superhyway_bus *bus;
- int ret = 0;
+ int ret;
- device_register(&superhyway_bus_device);
+ ret = device_register(&superhyway_bus_device);
+ if (unlikely(ret))
+ return ret;
for (bus = superhyway_channels; bus->ops; bus++)
ret |= superhyway_scan_bus(bus);
return ret;
}
-
postcore_initcall(superhyway_init);
static const struct superhyway_device_id *
diff --git a/include/asm-sh/cacheflush.h b/include/asm-sh/cacheflush.h
index aa558da..b912461 100644
--- a/include/asm-sh/cacheflush.h
+++ b/include/asm-sh/cacheflush.h
@@ -43,21 +43,31 @@
extern void __flush_invalidate_region(void *start, int size);
#endif
-#define flush_cache_vmap(start, end) flush_cache_all()
-#define flush_cache_vunmap(start, end) flush_cache_all()
+#ifdef CONFIG_CPU_SH4
+extern void copy_to_user_page(struct vm_area_struct *vma,
+ struct page *page, unsigned long vaddr, void *dst, const void *src,
+ unsigned long len);
-#define copy_to_user_page(vma, page, vaddr, dst, src, len) \
+extern void copy_from_user_page(struct vm_area_struct *vma,
+ struct page *page, unsigned long vaddr, void *dst, const void *src,
+ unsigned long len);
+#else
+#define copy_to_user_page(vma, page, vaddr, dst, src, len) \
do { \
flush_cache_page(vma, vaddr, page_to_pfn(page));\
memcpy(dst, src, len); \
flush_icache_user_range(vma, page, vaddr, len); \
} while (0)
-#define copy_from_user_page(vma, page, vaddr, dst, src, len) \
+#define copy_from_user_page(vma, page, vaddr, dst, src, len) \
do { \
flush_cache_page(vma, vaddr, page_to_pfn(page));\
memcpy(dst, src, len); \
} while (0)
+#endif
+
+#define flush_cache_vmap(start, end) flush_cache_all()
+#define flush_cache_vunmap(start, end) flush_cache_all()
#define HAVE_ARCH_UNMAPPED_AREA
diff --git a/include/asm-sh/cpu-sh3/timer.h b/include/asm-sh/cpu-sh3/timer.h
index 3880ce0..7b795ac 100644
--- a/include/asm-sh/cpu-sh3/timer.h
+++ b/include/asm-sh/cpu-sh3/timer.h
@@ -23,8 +23,7 @@
* ---------------------------------------------------------------------------
*/
-#if !defined(CONFIG_CPU_SUBTYPE_SH7720) && \
- !defined(CONFIG_CPU_SUBTYPE_SH7727)
+#if !defined(CONFIG_CPU_SUBTYPE_SH7720)
#define TMU_TOCR 0xfffffe90 /* Byte access */
#endif
@@ -58,8 +57,7 @@
#define TMU2_TCOR 0xfffffeac /* Long access */
#define TMU2_TCNT 0xfffffeb0 /* Long access */
#define TMU2_TCR 0xfffffeb4 /* Word access */
-#if !defined(CONFIG_CPU_SUBTYPE_SH7720) && \
- !defined(CONFIG_CPU_SUBTYPE_SH7727)
+#if !defined(CONFIG_CPU_SUBTYPE_SH7720)
#define TMU2_TCPR2 0xfffffeb8 /* Long access */
#endif
#endif
diff --git a/include/asm-sh/page.h b/include/asm-sh/page.h
index 3aa8b07..d00a8fd 100644
--- a/include/asm-sh/page.h
+++ b/include/asm-sh/page.h
@@ -73,10 +73,13 @@
#if !defined(CONFIG_CACHE_OFF) && defined(CONFIG_MMU) && \
(defined(CONFIG_CPU_SH4) || defined(CONFIG_SH7705_CACHE_32KB))
struct page;
-extern void clear_user_page(void *to, unsigned long address, struct page *pg);
-extern void copy_user_page(void *to, void *from, unsigned long address, struct page *pg);
-extern void __clear_user_page(void *to, void *orig_to);
-extern void __copy_user_page(void *to, void *from, void *orig_to);
+struct vm_area_struct;
+extern void clear_user_page(void *to, unsigned long address, struct page *page);
+#ifdef CONFIG_CPU_SH4
+extern void copy_user_highpage(struct page *to, struct page *from,
+ unsigned long vaddr, struct vm_area_struct *vma);
+#define __HAVE_ARCH_COPY_USER_HIGHPAGE
+#endif
#else
#define clear_user_page(page, vaddr, pg) clear_page(page)
#define copy_user_page(to, from, vaddr, pg) copy_page(to, from)
diff --git a/include/asm-sh/pgtable.h b/include/asm-sh/pgtable.h
index 0b1d7c6..8f1e8be 100644
--- a/include/asm-sh/pgtable.h
+++ b/include/asm-sh/pgtable.h
@@ -322,7 +322,9 @@
#define PAGE_KERNEL __pgprot(0)
#define PAGE_KERNEL_NOCACHE __pgprot(0)
#define PAGE_KERNEL_RO __pgprot(0)
-#define PAGE_KERNEL_PCC __pgprot(0)
+
+#define PAGE_KERNEL_PCC(slot, type) \
+ __pgprot(0)
#endif
#endif /* __ASSEMBLY__ */
diff --git a/include/asm-sh/processor.h b/include/asm-sh/processor.h
index ab0028d..fda6848 100644
--- a/include/asm-sh/processor.h
+++ b/include/asm-sh/processor.h
@@ -49,7 +49,7 @@
/* SH-4 types */
CPU_SH7750, CPU_SH7750S, CPU_SH7750R, CPU_SH7751, CPU_SH7751R,
- CPU_SH7760, CPU_ST40RA, CPU_ST40GX1, CPU_SH4_202, CPU_SH4_501,
+ CPU_SH7760, CPU_SH4_202, CPU_SH4_501,
/* SH-4A types */
CPU_SH7770, CPU_SH7780, CPU_SH7781, CPU_SH7785, CPU_SHX3,
diff --git a/include/asm-sh/ptrace.h b/include/asm-sh/ptrace.h
index ed358a3..b9789c8 100644
--- a/include/asm-sh/ptrace.h
+++ b/include/asm-sh/ptrace.h
@@ -42,9 +42,6 @@
#define REG_FPSCR 55
#define REG_FPUL 56
-/* options set using PTRACE_SETOPTIONS */
-#define PTRACE_O_TRACESYSGOOD 0x00000001
-
/*
* This struct defines the way the registers are stored on the
* kernel stack during a system call or other kernel entry.
diff --git a/include/asm-sh/vga.h b/include/asm-sh/vga.h
new file mode 100644
index 0000000..06a5de8
--- /dev/null
+++ b/include/asm-sh/vga.h
@@ -0,0 +1,6 @@
+#ifndef __ASM_SH_VGA_H
+#define __ASM_SH_VGA_H
+
+/* Stupid drivers. */
+
+#endif /* __ASM_SH_VGA_H */
diff --git a/include/asm-sh64/ptrace.h b/include/asm-sh64/ptrace.h
index a6d4da5..c424f80 100644
--- a/include/asm-sh64/ptrace.h
+++ b/include/asm-sh64/ptrace.h
@@ -32,6 +32,4 @@
extern void show_regs(struct pt_regs *);
#endif
-#define PTRACE_O_TRACESYSGOOD 0x00000001
-
#endif /* __ASM_SH64_PTRACE_H */