[libata] use dev_printk() throughout drivers
A few drivers were not following the standard meme of printing out
their driver name and version at module load time; this is fixed
as well.
diff --git a/drivers/scsi/ahci.c b/drivers/scsi/ahci.c
index 5efb3c5..e2a5657 100644
--- a/drivers/scsi/ahci.c
+++ b/drivers/scsi/ahci.c
@@ -41,6 +41,7 @@
#include <linux/interrupt.h>
#include <linux/sched.h>
#include <linux/dma-mapping.h>
+#include <linux/device.h>
#include "scsi.h"
#include <scsi/scsi_host.h>
#include <linux/libata.h>
@@ -674,10 +675,10 @@
if (!ahci_host_intr(ap, qc))
if (ata_ratelimit()) {
struct pci_dev *pdev =
- to_pci_dev(ap->host_set->dev);
- printk(KERN_WARNING
- "ahci(%s): unhandled interrupt on port %u\n",
- pci_name(pdev), i);
+ to_pci_dev(ap->host_set->dev);
+ dev_printk(KERN_WARNING, &pdev->dev,
+ "unhandled interrupt on port %u\n",
+ i);
}
VPRINTK("port %u\n", i);
@@ -685,10 +686,9 @@
VPRINTK("port %u (no irq)\n", i);
if (ata_ratelimit()) {
struct pci_dev *pdev =
- to_pci_dev(ap->host_set->dev);
- printk(KERN_WARNING
- "ahci(%s): interrupt on disabled port %u\n",
- pci_name(pdev), i);
+ to_pci_dev(ap->host_set->dev);
+ dev_printk(KERN_WARNING, &pdev->dev,
+ "interrupt on disabled port %u\n", i);
}
}
@@ -760,8 +760,8 @@
tmp = readl(mmio + HOST_CTL);
if (tmp & HOST_RESET) {
- printk(KERN_ERR DRV_NAME "(%s): controller reset failed (0x%x)\n",
- pci_name(pdev), tmp);
+ dev_printk(KERN_ERR, &pdev->dev,
+ "controller reset failed (0x%x)\n", tmp);
return -EIO;
}
@@ -789,22 +789,22 @@
if (rc) {
rc = pci_set_consistent_dma_mask(pdev, DMA_32BIT_MASK);
if (rc) {
- printk(KERN_ERR DRV_NAME "(%s): 64-bit DMA enable failed\n",
- pci_name(pdev));
+ dev_printk(KERN_ERR, &pdev->dev,
+ "64-bit DMA enable failed\n");
return rc;
}
}
} else {
rc = pci_set_dma_mask(pdev, DMA_32BIT_MASK);
if (rc) {
- printk(KERN_ERR DRV_NAME "(%s): 32-bit DMA enable failed\n",
- pci_name(pdev));
+ dev_printk(KERN_ERR, &pdev->dev,
+ "32-bit DMA enable failed\n");
return rc;
}
rc = pci_set_consistent_dma_mask(pdev, DMA_32BIT_MASK);
if (rc) {
- printk(KERN_ERR DRV_NAME "(%s): 32-bit consistent DMA enable failed\n",
- pci_name(pdev));
+ dev_printk(KERN_ERR, &pdev->dev,
+ "32-bit consistent DMA enable failed\n");
return rc;
}
}
@@ -907,10 +907,10 @@
else
scc_s = "unknown";
- printk(KERN_INFO DRV_NAME "(%s) AHCI %02x%02x.%02x%02x "
+ dev_printk(KERN_INFO, &pdev->dev,
+ "AHCI %02x%02x.%02x%02x "
"%u slots %u ports %s Gbps 0x%x impl %s mode\n"
,
- pci_name(pdev),
(vers >> 24) & 0xff,
(vers >> 16) & 0xff,
@@ -923,11 +923,11 @@
impl,
scc_s);
- printk(KERN_INFO DRV_NAME "(%s) flags: "
+ dev_printk(KERN_INFO, &pdev->dev,
+ "flags: "
"%s%s%s%s%s%s"
"%s%s%s%s%s%s%s\n"
,
- pci_name(pdev),
cap & (1 << 31) ? "64bit " : "",
cap & (1 << 30) ? "ncq " : "",
@@ -960,7 +960,7 @@
VPRINTK("ENTER\n");
if (!printed_version++)
- printk(KERN_DEBUG DRV_NAME " version " DRV_VERSION "\n");
+ dev_printk(KERN_DEBUG, &pdev->dev, "version " DRV_VERSION "\n");
rc = pci_enable_device(pdev);
if (rc)
diff --git a/drivers/scsi/pdc_adma.c b/drivers/scsi/pdc_adma.c
index 74b3b2c..665017e 100644
--- a/drivers/scsi/pdc_adma.c
+++ b/drivers/scsi/pdc_adma.c
@@ -40,6 +40,7 @@
#include <linux/delay.h>
#include <linux/interrupt.h>
#include <linux/sched.h>
+#include <linux/device.h>
#include "scsi.h"
#include <scsi/scsi_host.h>
#include <asm/io.h>
@@ -626,16 +627,14 @@
rc = pci_set_dma_mask(pdev, DMA_32BIT_MASK);
if (rc) {
- printk(KERN_ERR DRV_NAME
- "(%s): 32-bit DMA enable failed\n",
- pci_name(pdev));
+ dev_printk(KERN_ERR, &pdev->dev,
+ "32-bit DMA enable failed\n");
return rc;
}
rc = pci_set_consistent_dma_mask(pdev, DMA_32BIT_MASK);
if (rc) {
- printk(KERN_ERR DRV_NAME
- "(%s): 32-bit consistent DMA enable failed\n",
- pci_name(pdev));
+ dev_printk(KERN_ERR, &pdev->dev,
+ "32-bit consistent DMA enable failed\n");
return rc;
}
return 0;
@@ -651,7 +650,7 @@
int rc, port_no;
if (!printed_version++)
- printk(KERN_DEBUG DRV_NAME " version " DRV_VERSION "\n");
+ dev_printk(KERN_DEBUG, &pdev->dev, "version " DRV_VERSION "\n");
rc = pci_enable_device(pdev);
if (rc)
diff --git a/drivers/scsi/sata_mv.c b/drivers/scsi/sata_mv.c
index 936d1ce..46dbdee 100644
--- a/drivers/scsi/sata_mv.c
+++ b/drivers/scsi/sata_mv.c
@@ -29,6 +29,7 @@
#include <linux/interrupt.h>
#include <linux/sched.h>
#include <linux/dma-mapping.h>
+#include <linux/device.h>
#include "scsi.h"
#include <scsi/scsi_host.h>
#include <linux/libata.h>
@@ -1437,9 +1438,9 @@
else
scc_s = "unknown";
- printk(KERN_INFO DRV_NAME
- "(%s) %u slots %u ports %s mode IRQ via %s\n",
- pci_name(pdev), (unsigned)MV_MAX_Q_DEPTH, probe_ent->n_ports,
+ dev_printk(KERN_INFO, &pdev->dev,
+ "%u slots %u ports %s mode IRQ via %s\n",
+ (unsigned)MV_MAX_Q_DEPTH, probe_ent->n_ports,
scc_s, (MV_HP_FLAG_MSI & hpriv->hp_flags) ? "MSI" : "INTx");
}
@@ -1460,9 +1461,8 @@
void __iomem *mmio_base;
int pci_dev_busy = 0, rc;
- if (!printed_version++) {
- printk(KERN_INFO DRV_NAME " version " DRV_VERSION "\n");
- }
+ if (!printed_version++)
+ dev_printk(KERN_INFO, &pdev->dev, "version " DRV_VERSION "\n");
rc = pci_enable_device(pdev);
if (rc) {
diff --git a/drivers/scsi/sata_nv.c b/drivers/scsi/sata_nv.c
index 1a56d6c..d573888 100644
--- a/drivers/scsi/sata_nv.c
+++ b/drivers/scsi/sata_nv.c
@@ -61,6 +61,7 @@
#include <linux/blkdev.h>
#include <linux/delay.h>
#include <linux/interrupt.h>
+#include <linux/device.h>
#include "scsi.h"
#include <scsi/scsi_host.h>
#include <linux/libata.h>
@@ -383,7 +384,7 @@
return -ENODEV;
if (!printed_version++)
- printk(KERN_DEBUG DRV_NAME " version " DRV_VERSION "\n");
+ dev_printk(KERN_DEBUG, &pdev->dev, "version " DRV_VERSION "\n");
rc = pci_enable_device(pdev);
if (rc)
diff --git a/drivers/scsi/sata_promise.c b/drivers/scsi/sata_promise.c
index 8f41702..b41c977 100644
--- a/drivers/scsi/sata_promise.c
+++ b/drivers/scsi/sata_promise.c
@@ -38,6 +38,7 @@
#include <linux/delay.h>
#include <linux/interrupt.h>
#include <linux/sched.h>
+#include <linux/device.h>
#include "scsi.h"
#include <scsi/scsi_host.h>
#include <linux/libata.h>
@@ -633,7 +634,7 @@
int rc;
if (!printed_version++)
- printk(KERN_DEBUG DRV_NAME " version " DRV_VERSION "\n");
+ dev_printk(KERN_DEBUG, &pdev->dev, "version " DRV_VERSION "\n");
/*
* If this driver happens to only be useful on Apple's K2, then
diff --git a/drivers/scsi/sata_qstor.c b/drivers/scsi/sata_qstor.c
index d95a02f..9938dae 100644
--- a/drivers/scsi/sata_qstor.c
+++ b/drivers/scsi/sata_qstor.c
@@ -35,6 +35,7 @@
#include <linux/delay.h>
#include <linux/interrupt.h>
#include <linux/sched.h>
+#include <linux/device.h>
#include "scsi.h"
#include <scsi/scsi_host.h>
#include <asm/io.h>
@@ -600,25 +601,22 @@
if (rc) {
rc = pci_set_consistent_dma_mask(pdev, DMA_32BIT_MASK);
if (rc) {
- printk(KERN_ERR DRV_NAME
- "(%s): 64-bit DMA enable failed\n",
- pci_name(pdev));
+ dev_printk(KERN_ERR, &pdev->dev,
+ "64-bit DMA enable failed\n");
return rc;
}
}
} else {
rc = pci_set_dma_mask(pdev, DMA_32BIT_MASK);
if (rc) {
- printk(KERN_ERR DRV_NAME
- "(%s): 32-bit DMA enable failed\n",
- pci_name(pdev));
+ dev_printk(KERN_ERR, &pdev->dev,
+ "32-bit DMA enable failed\n");
return rc;
}
rc = pci_set_consistent_dma_mask(pdev, DMA_32BIT_MASK);
if (rc) {
- printk(KERN_ERR DRV_NAME
- "(%s): 32-bit consistent DMA enable failed\n",
- pci_name(pdev));
+ dev_printk(KERN_ERR, &pdev->dev,
+ "32-bit consistent DMA enable failed\n");
return rc;
}
}
@@ -635,7 +633,7 @@
int rc, port_no;
if (!printed_version++)
- printk(KERN_DEBUG DRV_NAME " version " DRV_VERSION "\n");
+ dev_printk(KERN_DEBUG, &pdev->dev, "version " DRV_VERSION "\n");
rc = pci_enable_device(pdev);
if (rc)
diff --git a/drivers/scsi/sata_sil.c b/drivers/scsi/sata_sil.c
index 3a05617..435f7e0 100644
--- a/drivers/scsi/sata_sil.c
+++ b/drivers/scsi/sata_sil.c
@@ -41,6 +41,7 @@
#include <linux/blkdev.h>
#include <linux/delay.h>
#include <linux/interrupt.h>
+#include <linux/device.h>
#include "scsi.h"
#include <scsi/scsi_host.h>
#include <linux/libata.h>
@@ -386,7 +387,7 @@
u8 cls;
if (!printed_version++)
- printk(KERN_DEBUG DRV_NAME " version " DRV_VERSION "\n");
+ dev_printk(KERN_DEBUG, &pdev->dev, "version " DRV_VERSION "\n");
/*
* If this driver happens to only be useful on Apple's K2, then
@@ -463,8 +464,8 @@
writeb(cls, mmio_base + SIL_FIFO_W3);
}
} else
- printk(KERN_WARNING DRV_NAME "(%s): cache line size not set. Driver may not function\n",
- pci_name(pdev));
+ dev_printk(KERN_WARNING, &pdev->dev,
+ "cache line size not set. Driver may not function\n");
if (ent->driver_data == sil_3114) {
irq_mask = SIL_MASK_4PORT;
diff --git a/drivers/scsi/sata_sil24.c b/drivers/scsi/sata_sil24.c
index 4afe2b1..c665480 100644
--- a/drivers/scsi/sata_sil24.c
+++ b/drivers/scsi/sata_sil24.c
@@ -35,6 +35,7 @@
#include <linux/delay.h>
#include <linux/interrupt.h>
#include <linux/dma-mapping.h>
+#include <linux/device.h>
#include <scsi/scsi_host.h>
#include "scsi.h"
#include <linux/libata.h>
@@ -690,7 +691,7 @@
int i, rc;
if (!printed_version++)
- printk(KERN_DEBUG DRV_NAME " version " DRV_VERSION "\n");
+ dev_printk(KERN_DEBUG, &pdev->dev, "version " DRV_VERSION "\n");
rc = pci_enable_device(pdev);
if (rc)
@@ -750,14 +751,14 @@
*/
rc = pci_set_dma_mask(pdev, DMA_32BIT_MASK);
if (rc) {
- printk(KERN_ERR DRV_NAME "(%s): 32-bit DMA enable failed\n",
- pci_name(pdev));
+ dev_printk(KERN_ERR, &pdev->dev,
+ "32-bit DMA enable failed\n");
goto out_free;
}
rc = pci_set_consistent_dma_mask(pdev, DMA_32BIT_MASK);
if (rc) {
- printk(KERN_ERR DRV_NAME "(%s): 32-bit consistent DMA enable failed\n",
- pci_name(pdev));
+ dev_printk(KERN_ERR, &pdev->dev,
+ "32-bit consistent DMA enable failed\n");
goto out_free;
}
@@ -793,9 +794,8 @@
break;
}
if (tmp & PORT_CS_PORT_RST)
- printk(KERN_ERR DRV_NAME
- "(%s): failed to clear port RST\n",
- pci_name(pdev));
+ dev_printk(KERN_ERR, &pdev->dev,
+ "failed to clear port RST\n");
}
/* Zero error counters. */
@@ -824,9 +824,8 @@
/* Reset itself */
if (__sil24_reset_controller(port))
- printk(KERN_ERR DRV_NAME
- "(%s): failed to reset controller\n",
- pci_name(pdev));
+ dev_printk(KERN_ERR, &pdev->dev,
+ "failed to reset controller\n");
}
/* Turn on interrupts */
diff --git a/drivers/scsi/sata_sis.c b/drivers/scsi/sata_sis.c
index 057f7b9..42288be 100644
--- a/drivers/scsi/sata_sis.c
+++ b/drivers/scsi/sata_sis.c
@@ -38,6 +38,7 @@
#include <linux/blkdev.h>
#include <linux/delay.h>
#include <linux/interrupt.h>
+#include <linux/device.h>
#include "scsi.h"
#include <scsi/scsi_host.h>
#include <linux/libata.h>
@@ -237,6 +238,7 @@
static int sis_init_one (struct pci_dev *pdev, const struct pci_device_id *ent)
{
+ static int printed_version;
struct ata_probe_ent *probe_ent = NULL;
int rc;
u32 genctl;
@@ -245,6 +247,9 @@
u8 pmr;
u8 port2_start;
+ if (!printed_version++)
+ dev_printk(KERN_INFO, &pdev->dev, "version " DRV_VERSION "\n");
+
rc = pci_enable_device(pdev);
if (rc)
return rc;
@@ -288,16 +293,18 @@
pci_read_config_byte(pdev, SIS_PMR, &pmr);
if (ent->device != 0x182) {
if ((pmr & SIS_PMR_COMBINED) == 0) {
- printk(KERN_INFO "sata_sis: Detected SiS 180/181 chipset in SATA mode\n");
+ dev_printk(KERN_INFO, &pdev->dev,
+ "Detected SiS 180/181 chipset in SATA mode\n");
port2_start = 64;
}
else {
- printk(KERN_INFO "sata_sis: Detected SiS 180/181 chipset in combined mode\n");
+ dev_printk(KERN_INFO, &pdev->dev,
+ "Detected SiS 180/181 chipset in combined mode\n");
port2_start=0;
}
}
else {
- printk(KERN_INFO "sata_sis: Detected SiS 182 chipset\n");
+ dev_printk(KERN_INFO, &pdev->dev, "Detected SiS 182 chipset\n");
port2_start = 0x20;
}
diff --git a/drivers/scsi/sata_svw.c b/drivers/scsi/sata_svw.c
index 46208f5..db615ff 100644
--- a/drivers/scsi/sata_svw.c
+++ b/drivers/scsi/sata_svw.c
@@ -44,6 +44,7 @@
#include <linux/blkdev.h>
#include <linux/delay.h>
#include <linux/interrupt.h>
+#include <linux/device.h>
#include "scsi.h"
#include <scsi/scsi_host.h>
#include <linux/libata.h>
@@ -362,7 +363,7 @@
int i;
if (!printed_version++)
- printk(KERN_DEBUG DRV_NAME " version " DRV_VERSION "\n");
+ dev_printk(KERN_DEBUG, &pdev->dev, "version " DRV_VERSION "\n");
/*
* If this driver happens to only be useful on Apple's K2, then
diff --git a/drivers/scsi/sata_sx4.c b/drivers/scsi/sata_sx4.c
index d9a8baf..0ec21e09 100644
--- a/drivers/scsi/sata_sx4.c
+++ b/drivers/scsi/sata_sx4.c
@@ -38,6 +38,7 @@
#include <linux/delay.h>
#include <linux/interrupt.h>
#include <linux/sched.h>
+#include <linux/device.h>
#include "scsi.h"
#include <scsi/scsi_host.h>
#include <linux/libata.h>
@@ -1385,7 +1386,7 @@
int rc;
if (!printed_version++)
- printk(KERN_DEBUG DRV_NAME " version " DRV_VERSION "\n");
+ dev_printk(KERN_DEBUG, &pdev->dev, "version " DRV_VERSION "\n");
/*
* If this driver happens to only be useful on Apple's K2, then
diff --git a/drivers/scsi/sata_uli.c b/drivers/scsi/sata_uli.c
index d68dc7d..a5e245c 100644
--- a/drivers/scsi/sata_uli.c
+++ b/drivers/scsi/sata_uli.c
@@ -32,6 +32,7 @@
#include <linux/blkdev.h>
#include <linux/delay.h>
#include <linux/interrupt.h>
+#include <linux/device.h>
#include "scsi.h"
#include <scsi/scsi_host.h>
#include <linux/libata.h>
@@ -178,12 +179,16 @@
static int uli_init_one (struct pci_dev *pdev, const struct pci_device_id *ent)
{
+ static int printed_version;
struct ata_probe_ent *probe_ent;
struct ata_port_info *ppi;
int rc;
unsigned int board_idx = (unsigned int) ent->driver_data;
int pci_dev_busy = 0;
+ if (!printed_version++)
+ dev_printk(KERN_INFO, &pdev->dev, "version " DRV_VERSION "\n");
+
rc = pci_enable_device(pdev);
if (rc)
return rc;
diff --git a/drivers/scsi/sata_via.c b/drivers/scsi/sata_via.c
index 80e291a..b3ecdbe 100644
--- a/drivers/scsi/sata_via.c
+++ b/drivers/scsi/sata_via.c
@@ -41,6 +41,7 @@
#include <linux/init.h>
#include <linux/blkdev.h>
#include <linux/delay.h>
+#include <linux/device.h>
#include "scsi.h"
#include <scsi/scsi_host.h>
#include <linux/libata.h>
@@ -259,15 +260,15 @@
u8 tmp8;
pci_read_config_byte(pdev, PCI_INTERRUPT_LINE, &tmp8);
- printk(KERN_INFO DRV_NAME "(%s): routed to hard irq line %d\n",
- pci_name(pdev),
+ dev_printk(KERN_INFO, &pdev->dev, "routed to hard irq line %d\n",
(int) (tmp8 & 0xf0) == 0xf0 ? 0 : tmp8 & 0x0f);
/* make sure SATA channels are enabled */
pci_read_config_byte(pdev, SATA_CHAN_ENAB, &tmp8);
if ((tmp8 & ALL_PORTS) != ALL_PORTS) {
- printk(KERN_DEBUG DRV_NAME "(%s): enabling SATA channels (0x%x)\n",
- pci_name(pdev), (int) tmp8);
+ dev_printk(KERN_DEBUG, &pdev->dev,
+ "enabling SATA channels (0x%x)\n",
+ (int) tmp8);
tmp8 |= ALL_PORTS;
pci_write_config_byte(pdev, SATA_CHAN_ENAB, tmp8);
}
@@ -275,8 +276,9 @@
/* make sure interrupts for each channel sent to us */
pci_read_config_byte(pdev, SATA_INT_GATE, &tmp8);
if ((tmp8 & ALL_PORTS) != ALL_PORTS) {
- printk(KERN_DEBUG DRV_NAME "(%s): enabling SATA channel interrupts (0x%x)\n",
- pci_name(pdev), (int) tmp8);
+ dev_printk(KERN_DEBUG, &pdev->dev,
+ "enabling SATA channel interrupts (0x%x)\n",
+ (int) tmp8);
tmp8 |= ALL_PORTS;
pci_write_config_byte(pdev, SATA_INT_GATE, tmp8);
}
@@ -284,8 +286,9 @@
/* make sure native mode is enabled */
pci_read_config_byte(pdev, SATA_NATIVE_MODE, &tmp8);
if ((tmp8 & NATIVE_MODE_ALL) != NATIVE_MODE_ALL) {
- printk(KERN_DEBUG DRV_NAME "(%s): enabling SATA channel native mode (0x%x)\n",
- pci_name(pdev), (int) tmp8);
+ dev_printk(KERN_DEBUG, &pdev->dev,
+ "enabling SATA channel native mode (0x%x)\n",
+ (int) tmp8);
tmp8 |= NATIVE_MODE_ALL;
pci_write_config_byte(pdev, SATA_NATIVE_MODE, tmp8);
}
@@ -303,7 +306,7 @@
u8 tmp8;
if (!printed_version++)
- printk(KERN_DEBUG DRV_NAME " version " DRV_VERSION "\n");
+ dev_printk(KERN_DEBUG, &pdev->dev, "version " DRV_VERSION "\n");
rc = pci_enable_device(pdev);
if (rc)
@@ -318,8 +321,9 @@
if (board_id == vt6420) {
pci_read_config_byte(pdev, SATA_PATA_SHARING, &tmp8);
if (tmp8 & SATA_2DEV) {
- printk(KERN_ERR DRV_NAME "(%s): SATA master/slave not supported (0x%x)\n",
- pci_name(pdev), (int) tmp8);
+ dev_printk(KERN_ERR, &pdev->dev,
+ "SATA master/slave not supported (0x%x)\n",
+ (int) tmp8);
rc = -EIO;
goto err_out_regions;
}
@@ -332,10 +336,11 @@
for (i = 0; i < ARRAY_SIZE(svia_bar_sizes); i++)
if ((pci_resource_start(pdev, i) == 0) ||
(pci_resource_len(pdev, i) < bar_sizes[i])) {
- printk(KERN_ERR DRV_NAME "(%s): invalid PCI BAR %u (sz 0x%lx, val 0x%lx)\n",
- pci_name(pdev), i,
- pci_resource_start(pdev, i),
- pci_resource_len(pdev, i));
+ dev_printk(KERN_ERR, &pdev->dev,
+ "invalid PCI BAR %u (sz 0x%lx, val 0x%lx)\n",
+ i,
+ pci_resource_start(pdev, i),
+ pci_resource_len(pdev, i));
rc = -ENODEV;
goto err_out_regions;
}
@@ -353,8 +358,7 @@
probe_ent = vt6421_init_probe_ent(pdev);
if (!probe_ent) {
- printk(KERN_ERR DRV_NAME "(%s): out of memory\n",
- pci_name(pdev));
+ dev_printk(KERN_ERR, &pdev->dev, "out of memory\n");
rc = -ENOMEM;
goto err_out_regions;
}
diff --git a/drivers/scsi/sata_vsc.c b/drivers/scsi/sata_vsc.c
index 54273e0..bb84ba0 100644
--- a/drivers/scsi/sata_vsc.c
+++ b/drivers/scsi/sata_vsc.c
@@ -42,6 +42,7 @@
#include <linux/delay.h>
#include <linux/interrupt.h>
#include <linux/dma-mapping.h>
+#include <linux/device.h>
#include "scsi.h"
#include <scsi/scsi_host.h>
#include <linux/libata.h>
@@ -295,7 +296,7 @@
int rc;
if (!printed_version++)
- printk(KERN_DEBUG DRV_NAME " version " DRV_VERSION "\n");
+ dev_printk(KERN_DEBUG, &pdev->dev, "version " DRV_VERSION "\n");
rc = pci_enable_device(pdev);
if (rc)