arch/arm/mach-davinci/board-mityomapl138.c

/*
 * Critical Link MityOMAP-L138 SoM
 *
 * Copyright (C) 2010 Critical Link LLC - http://www.criticallink.com
 *
 * This file is licensed under the terms of the GNU General Public License
 * version 2. This program is licensed "as is" without any warranty of
 * any kind, whether express or implied.
 */

#include <linux/kernel.h>
#include <linux/init.h>
#include <linux/console.h>
#include <linux/platform_device.h>
#include <linux/mtd/partitions.h>
#include <linux/regulator/machine.h>
#include <linux/i2c.h>
#include <linux/i2c/at24.h>
#include <linux/etherdevice.h>

#include <asm/mach-types.h>
#include <asm/mach/arch.h>
#include <mach/common.h>
#include <mach/cp_intc.h>
#include <mach/da8xx.h>
#include <mach/nand.h>
#include <mach/mux.h>

#define MITYOMAPL138_PHY_ID		"0:03"

#define FACTORY_CONFIG_MAGIC	0x012C0138
#define FACTORY_CONFIG_VERSION	0x00010001

/* Data Held in On-Board I2C device */
struct factory_config {
	u32	magic;
	u32	version;
	u8	mac[6];
	u32	fpga_type;
	u32	spare;
	u32	serialnumber;
	char	partnum[32];
};

static struct factory_config factory_config;

static void read_factory_config(struct memory_accessor *a, void *context)
{
	int ret;
	struct davinci_soc_info *soc_info = &davinci_soc_info;

	ret = a->read(a, (char *)&factory_config, 0, sizeof(factory_config));
	if (ret != sizeof(struct factory_config)) {
		pr_warning("MityOMAPL138: Read Factory Config Failed: %d\n",
				ret);
		return;
	}

	if (factory_config.magic != FACTORY_CONFIG_MAGIC) {
		pr_warning("MityOMAPL138: Factory Config Magic Wrong (%X)\n",
				factory_config.magic);
		return;
	}

	if (factory_config.version != FACTORY_CONFIG_VERSION) {
		pr_warning("MityOMAPL138: Factory Config Version Wrong (%X)\n",
				factory_config.version);
		return;
	}

	pr_info("MityOMAPL138: Found MAC = %pM\n", factory_config.mac);
	pr_info("MityOMAPL138: Part Number = %s\n", factory_config.partnum);
	if (is_valid_ether_addr(factory_config.mac))
		memcpy(soc_info->emac_pdata->mac_addr,
			factory_config.mac, ETH_ALEN);
	else
		pr_warning("MityOMAPL138: Invalid MAC found "
				"in factory config block\n");
}

static struct at24_platform_data mityomapl138_fd_chip = {
	.byte_len	= 256,
	.page_size	= 8,
	.flags		= AT24_FLAG_READONLY | AT24_FLAG_IRUGO,
	.setup		= read_factory_config,
	.context	= NULL,
};

static struct davinci_i2c_platform_data mityomap_i2c_0_pdata = {
	.bus_freq	= 100,	/* kHz */
	.bus_delay	= 0,	/* usec */
};

/* TPS65023 voltage regulator support */
/* 1.2V Core */
static struct regulator_consumer_supply tps65023_dcdc1_consumers[] = {
	{
		.supply = "cvdd",
	},
};

/* 1.8V */
static struct regulator_consumer_supply tps65023_dcdc2_consumers[] = {
	{
		.supply = "usb0_vdda18",
	},
	{
		.supply = "usb1_vdda18",
	},
	{
		.supply = "ddr_dvdd18",
	},
	{
		.supply = "sata_vddr",
	},
};

/* 1.2V */
static struct regulator_consumer_supply tps65023_dcdc3_consumers[] = {
	{
		.supply = "sata_vdd",
	},
	{
		.supply = "usb_cvdd",
	},
	{
		.supply = "pll0_vdda",
	},
	{
		.supply = "pll1_vdda",
	},
};

/* 1.8V Aux LDO, not used */
static struct regulator_consumer_supply tps65023_ldo1_consumers[] = {
	{
		.supply = "1.8v_aux",
	},
};

/* FPGA VCC Aux (2.5 or 3.3) LDO */
static struct regulator_consumer_supply tps65023_ldo2_consumers[] = {
	{
		.supply = "vccaux",
	},
};

static struct regulator_init_data tps65023_regulator_data[] = {
	/* dcdc1 */
	{
		.constraints = {
			.min_uV = 1150000,
			.max_uV = 1350000,
			.valid_ops_mask = REGULATOR_CHANGE_VOLTAGE |
					  REGULATOR_CHANGE_STATUS,
			.boot_on = 1,
		},
		.num_consumer_supplies = ARRAY_SIZE(tps65023_dcdc1_consumers),
		.consumer_supplies = tps65023_dcdc1_consumers,
	},
	/* dcdc2 */
	{
		.constraints = {
			.min_uV = 1800000,
			.max_uV = 1800000,
			.valid_ops_mask = REGULATOR_CHANGE_STATUS,
			.boot_on = 1,
		},
		.num_consumer_supplies = ARRAY_SIZE(tps65023_dcdc2_consumers),
		.consumer_supplies = tps65023_dcdc2_consumers,
	},
	/* dcdc3 */
	{
		.constraints = {
			.min_uV = 1200000,
			.max_uV = 1200000,
			.valid_ops_mask = REGULATOR_CHANGE_STATUS,
			.boot_on = 1,
		},
		.num_consumer_supplies = ARRAY_SIZE(tps65023_dcdc3_consumers),
		.consumer_supplies = tps65023_dcdc3_consumers,
	},
	/* ldo1 */
	{
		.constraints = {
			.min_uV = 1800000,
			.max_uV = 1800000,
			.valid_ops_mask = REGULATOR_CHANGE_STATUS,
			.boot_on = 1,
		},
		.num_consumer_supplies = ARRAY_SIZE(tps65023_ldo1_consumers),
		.consumer_supplies = tps65023_ldo1_consumers,
	},
	/* ldo2 */
	{
		.constraints = {
			.min_uV = 2500000,
			.max_uV = 3300000,
			.valid_ops_mask = REGULATOR_CHANGE_VOLTAGE |
					  REGULATOR_CHANGE_STATUS,
			.boot_on = 1,
		},
		.num_consumer_supplies = ARRAY_SIZE(tps65023_ldo2_consumers),
		.consumer_supplies = tps65023_ldo2_consumers,
	},
};

static struct i2c_board_info __initdata mityomap_tps65023_info[] = {
	{
		I2C_BOARD_INFO("tps65023", 0x48),
		.platform_data = &tps65023_regulator_data[0],
	},
	{
		I2C_BOARD_INFO("24c02", 0x50),
		.platform_data = &mityomapl138_fd_chip,
	},
};

static int __init pmic_tps65023_init(void)
{
	return i2c_register_board_info(1, mityomap_tps65023_info,
					ARRAY_SIZE(mityomap_tps65023_info));
}

/*
 * MityDSP-L138 includes a 256 MByte large-page NAND flash
 * (128K blocks).
 */
static struct mtd_partition mityomapl138_nandflash_partition[] = {
	{
		.name		= "rootfs",
		.offset		= 0,
		.size		= SZ_128M,
		.mask_flags	= 0, /* MTD_WRITEABLE, */
	},
	{
		.name		= "homefs",
		.offset		= MTDPART_OFS_APPEND,
		.size		= MTDPART_SIZ_FULL,
		.mask_flags	= 0,
	},
};

static struct davinci_nand_pdata mityomapl138_nandflash_data = {
	.parts		= mityomapl138_nandflash_partition,
	.nr_parts	= ARRAY_SIZE(mityomapl138_nandflash_partition),
	.ecc_mode	= NAND_ECC_HW,
	.options	= NAND_USE_FLASH_BBT | NAND_BUSWIDTH_16,
	.ecc_bits	= 1, /* 4 bit mode is not supported with 16 bit NAND */
};

static struct resource mityomapl138_nandflash_resource[] = {
	{
		.start	= DA8XX_AEMIF_CS3_BASE,
		.end	= DA8XX_AEMIF_CS3_BASE + SZ_512K + 2 * SZ_1K - 1,
		.flags	= IORESOURCE_MEM,
	},
	{
		.start	= DA8XX_AEMIF_CTL_BASE,
		.end	= DA8XX_AEMIF_CTL_BASE + SZ_32K - 1,
		.flags	= IORESOURCE_MEM,
	},
};

static struct platform_device mityomapl138_nandflash_device = {
	.name		= "davinci_nand",
	.id		= 0,
	.dev		= {
		.platform_data	= &mityomapl138_nandflash_data,
	},
	.num_resources	= ARRAY_SIZE(mityomapl138_nandflash_resource),
	.resource	= mityomapl138_nandflash_resource,
};

static struct platform_device *mityomapl138_devices[] __initdata = {
	&mityomapl138_nandflash_device,
};

static void __init mityomapl138_setup_nand(void)
{
	platform_add_devices(mityomapl138_devices,
				 ARRAY_SIZE(mityomapl138_devices));
}

static struct davinci_uart_config mityomapl138_uart_config __initdata = {
	.enabled_uarts = 0x7,
};

static const short mityomap_mii_pins[] = {
	DA850_MII_TXEN, DA850_MII_TXCLK, DA850_MII_COL, DA850_MII_TXD_3,
	DA850_MII_TXD_2, DA850_MII_TXD_1, DA850_MII_TXD_0, DA850_MII_RXER,
	DA850_MII_CRS, DA850_MII_RXCLK, DA850_MII_RXDV, DA850_MII_RXD_3,
	DA850_MII_RXD_2, DA850_MII_RXD_1, DA850_MII_RXD_0, DA850_MDIO_CLK,
	DA850_MDIO_D,
	-1
};

static const short mityomap_rmii_pins[] = {
	DA850_RMII_TXD_0, DA850_RMII_TXD_1, DA850_RMII_TXEN,
	DA850_RMII_CRS_DV, DA850_RMII_RXD_0, DA850_RMII_RXD_1,
	DA850_RMII_RXER, DA850_RMII_MHZ_50_CLK, DA850_MDIO_CLK,
	DA850_MDIO_D,
	-1
};

static void __init mityomapl138_config_emac(void)
{
	void __iomem *cfg_chip3_base;
	int ret;
	u32 val;
	struct davinci_soc_info *soc_info = &davinci_soc_info;

	soc_info->emac_pdata->rmii_en = 0; /* hardcoded for now */

	cfg_chip3_base = DA8XX_SYSCFG0_VIRT(DA8XX_CFGCHIP3_REG);
	val = __raw_readl(cfg_chip3_base);

	if (soc_info->emac_pdata->rmii_en) {
		val |= BIT(8);
		ret = davinci_cfg_reg_list(mityomap_rmii_pins);
		pr_info("RMII PHY configured\n");
	} else {
		val &= ~BIT(8);
		ret = davinci_cfg_reg_list(mityomap_mii_pins);
		pr_info("MII PHY configured\n");
	}

	if (ret) {
		pr_warning("mii/rmii mux setup failed: %d\n", ret);
		return;
	}

	/* configure the CFGCHIP3 register for RMII or MII */
	__raw_writel(val, cfg_chip3_base);

	soc_info->emac_pdata->phy_id = MITYOMAPL138_PHY_ID;

	ret = da8xx_register_emac();
	if (ret)
		pr_warning("emac registration failed: %d\n", ret);
}

static struct davinci_pm_config da850_pm_pdata = {
	.sleepcount = 128,
};

static struct platform_device da850_pm_device = {
	.name	= "pm-davinci",
	.dev = {
		.platform_data  = &da850_pm_pdata,
	},
	.id	= -1,
};

static void __init mityomapl138_init(void)
{
	int ret;

	/* for now, no special EDMA channels are reserved */
	ret = da850_register_edma(NULL);
	if (ret)
		pr_warning("edma registration failed: %d\n", ret);

	ret = da8xx_register_watchdog();
	if (ret)
		pr_warning("watchdog registration failed: %d\n", ret);

	davinci_serial_init(&mityomapl138_uart_config);

	ret = da8xx_register_i2c(0, &mityomap_i2c_0_pdata);
	if (ret)
		pr_warning("i2c0 registration failed: %d\n", ret);

	ret = pmic_tps65023_init();
	if (ret)
		pr_warning("TPS65023 PMIC init failed: %d\n", ret);

	mityomapl138_setup_nand();

	mityomapl138_config_emac();

	ret = da8xx_register_rtc();
	if (ret)
		pr_warning("rtc setup failed: %d\n", ret);

	ret = da850_register_cpufreq("pll0_sysclk3");
	if (ret)
		pr_warning("cpufreq registration failed: %d\n", ret);

	ret = da8xx_register_cpuidle();
	if (ret)
		pr_warning("cpuidle registration failed: %d\n", ret);

	ret = da850_register_pm(&da850_pm_device);
	if (ret)
		pr_warning("da850_evm_init: suspend registration failed: %d\n",
				ret);
}

#ifdef CONFIG_SERIAL_8250_CONSOLE
static int __init mityomapl138_console_init(void)
{
	if (!machine_is_mityomapl138())
		return 0;

	return add_preferred_console("ttyS", 1, "115200");
}
console_initcall(mityomapl138_console_init);
#endif

static void __init mityomapl138_map_io(void)
{
	da850_init();
}

MACHINE_START(MITYOMAPL138, "MityDSP-L138/MityARM-1808")
	.boot_params	= (DA8XX_DDR_BASE + 0x100),
	.map_io		= mityomapl138_map_io,
	.init_irq	= cp_intc_init,
	.timer		= &davinci_timer,
	.init_machine	= mityomapl138_init,
MACHINE_END