serial: Make ucc_uart work in HW UART mode
In HW UART mode the TxBD[READY] is not cleared by H/W (RISC engine) when
the user send characters to Tx buffer of QE UART. So, these characters
stay on the QE forever, never go to UART line.
Signed-off-by: Dave Liu <daveliu@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
diff --git a/drivers/serial/ucc_uart.c b/drivers/serial/ucc_uart.c
index 7de66c0..e945e78 100644
--- a/drivers/serial/ucc_uart.c
+++ b/drivers/serial/ucc_uart.c
@@ -681,22 +681,27 @@
out_be16(&uccup->rccm, 0xc0ff);
/* Configure the GUMR registers for UART */
- if (soft_uart)
+ if (soft_uart) {
/* Soft-UART requires a 1X multiplier for TX */
clrsetbits_be32(&uccp->gumr_l,
UCC_SLOW_GUMR_L_MODE_MASK | UCC_SLOW_GUMR_L_TDCR_MASK |
UCC_SLOW_GUMR_L_RDCR_MASK,
UCC_SLOW_GUMR_L_MODE_UART | UCC_SLOW_GUMR_L_TDCR_1 |
UCC_SLOW_GUMR_L_RDCR_16);
- else
+
+ clrsetbits_be32(&uccp->gumr_h, UCC_SLOW_GUMR_H_RFW,
+ UCC_SLOW_GUMR_H_TRX | UCC_SLOW_GUMR_H_TTX);
+ } else {
clrsetbits_be32(&uccp->gumr_l,
UCC_SLOW_GUMR_L_MODE_MASK | UCC_SLOW_GUMR_L_TDCR_MASK |
UCC_SLOW_GUMR_L_RDCR_MASK,
UCC_SLOW_GUMR_L_MODE_UART | UCC_SLOW_GUMR_L_TDCR_16 |
UCC_SLOW_GUMR_L_RDCR_16);
- clrsetbits_be32(&uccp->gumr_h, UCC_SLOW_GUMR_H_RFW,
- UCC_SLOW_GUMR_H_TRX | UCC_SLOW_GUMR_H_TTX);
+ clrsetbits_be32(&uccp->gumr_h,
+ UCC_SLOW_GUMR_H_TRX | UCC_SLOW_GUMR_H_TTX,
+ UCC_SLOW_GUMR_H_RFW);
+ }
#ifdef LOOPBACK
clrsetbits_be32(&uccp->gumr_l, UCC_SLOW_GUMR_L_DIAG_MASK,
@@ -706,7 +711,7 @@
UCC_SLOW_GUMR_H_CDS);
#endif
- /* Enable rx interrupts and clear all pending events. */
+ /* Disable rx interrupts and clear all pending events. */
out_be16(&uccp->uccm, 0);
out_be16(&uccp->ucce, 0xffff);
out_be16(&uccp->udsr, 0x7e7e);
@@ -765,6 +770,10 @@
cecr_subblock = ucc_slow_get_qe_cr_subblock(qe_port->ucc_num);
qe_issue_cmd(QE_INIT_TX_RX, cecr_subblock,
QE_CR_PROTOCOL_UNSPECIFIED, 0);
+ } else {
+ cecr_subblock = ucc_slow_get_qe_cr_subblock(qe_port->ucc_num);
+ qe_issue_cmd(QE_INIT_TX_RX, cecr_subblock,
+ QE_CR_PROTOCOL_UART, 0);
}
}