diff --git a/Documentation/Changes b/Documentation/Changes
index abee7f5..73a8617 100644
--- a/Documentation/Changes
+++ b/Documentation/Changes
@@ -201,7 +201,7 @@
 ----
 udev is a userspace application for populating /dev dynamically with
 only entries for devices actually present.  udev replaces the basic
-functionality of devfs, while allowing persistant device naming for
+functionality of devfs, while allowing persistent device naming for
 devices.
 
 FUSE
diff --git a/Documentation/DMA-API.txt b/Documentation/DMA-API.txt
index 2ffb0d6..0543162 100644
--- a/Documentation/DMA-API.txt
+++ b/Documentation/DMA-API.txt
@@ -489,7 +489,7 @@
 flags can be or'd together and are
 
 DMA_MEMORY_MAP - request that the memory returned from
-dma_alloc_coherent() be directly writeable.
+dma_alloc_coherent() be directly writable.
 
 DMA_MEMORY_IO - request that the memory returned from
 dma_alloc_coherent() be addressable using read/write/memcpy_toio etc.
diff --git a/Documentation/DMA-ISA-LPC.txt b/Documentation/DMA-ISA-LPC.txt
index 705f6be..e767805 100644
--- a/Documentation/DMA-ISA-LPC.txt
+++ b/Documentation/DMA-ISA-LPC.txt
@@ -110,7 +110,7 @@
 
 Once the DMA transfer is finished (or timed out) you should disable
 the channel again. You should also check get_dma_residue() to make
-sure that all data has been transfered.
+sure that all data has been transferred.
 
 Example:
 
diff --git a/Documentation/DocBook/writing_usb_driver.tmpl b/Documentation/DocBook/writing_usb_driver.tmpl
index 07cd34c..d4188d4 100644
--- a/Documentation/DocBook/writing_usb_driver.tmpl
+++ b/Documentation/DocBook/writing_usb_driver.tmpl
@@ -345,8 +345,7 @@
         usb_buffer_free (dev->udev, dev->bulk_out_size,
             dev->bulk_out_buffer,
             dev->write_urb->transfer_dma);
-    if (dev->write_urb != NULL)
-        usb_free_urb (dev->write_urb);
+    usb_free_urb (dev->write_urb);
     kfree (dev);
 }
   </programlisting>
diff --git a/Documentation/MSI-HOWTO.txt b/Documentation/MSI-HOWTO.txt
index 5c34910..d389388 100644
--- a/Documentation/MSI-HOWTO.txt
+++ b/Documentation/MSI-HOWTO.txt
@@ -219,7 +219,7 @@
 Note that the pre-assigned IOAPIC dev->irq is valid only if the device
 operates in PIN-IRQ assertion mode. In MSI-X mode, any attempt at
 using dev->irq by the device driver to request for interrupt service
-may result unpredictabe behavior.
+may result in unpredictable behavior.
 
 For each MSI-X vector granted, a device driver is responsible for calling
 other functions like request_irq(), enable_irq(), etc. to enable
diff --git a/Documentation/accounting/taskstats.txt b/Documentation/accounting/taskstats.txt
index 92ebf29..ff06b73 100644
--- a/Documentation/accounting/taskstats.txt
+++ b/Documentation/accounting/taskstats.txt
@@ -96,9 +96,9 @@
 a pid/tgid will be followed by some stats.
 
 b) TASKSTATS_TYPE_PID/TGID: attribute whose payload is the pid/tgid whose stats
-is being returned.
+are being returned.
 
-c) TASKSTATS_TYPE_STATS: attribute with a struct taskstsats as payload. The
+c) TASKSTATS_TYPE_STATS: attribute with a struct taskstats as payload. The
 same structure is used for both per-pid and per-tgid stats.
 
 3. New message sent by kernel whenever a task exits. The payload consists of a
@@ -122,12 +122,12 @@
 
 However, maintaining per-process, in addition to per-task stats, within the
 kernel has space and time overheads. To address this, the taskstats code
-accumalates each exiting task's statistics into a process-wide data structure.
-When the last task of a process exits, the process level data accumalated also
+accumulates each exiting task's statistics into a process-wide data structure.
+When the last task of a process exits, the process level data accumulated also
 gets sent to userspace (along with the per-task data).
 
 When a user queries to get per-tgid data, the sum of all other live threads in
-the group is added up and added to the accumalated total for previously exited
+the group is added up and added to the accumulated total for previously exited
 threads of the same thread group.
 
 Extending taskstats
diff --git a/Documentation/block/biodoc.txt b/Documentation/block/biodoc.txt
index 34bf8f6..c6c9a9c 100644
--- a/Documentation/block/biodoc.txt
+++ b/Documentation/block/biodoc.txt
@@ -183,7 +183,7 @@
 modified to accomplish a direct page -> bus translation, without requiring
 a virtual address mapping (unlike the earlier scheme of virtual address
 -> bus translation). So this works uniformly for high-memory pages (which
-do not have a correponding kernel virtual address space mapping) and
+do not have a corresponding kernel virtual address space mapping) and
 low-memory pages.
 
 Note: Please refer to DMA-mapping.txt for a discussion on PCI high mem DMA
@@ -391,7 +391,7 @@
 on to the generic block layer, only to be merged by the i/o scheduler
 when the underlying device was capable of handling the i/o in one shot.
 Also, using the buffer head as an i/o structure for i/os that didn't originate
-from the buffer cache unecessarily added to the weight of the descriptors
+from the buffer cache unnecessarily added to the weight of the descriptors
 which were generated for each such chunk.
 
 The following were some of the goals and expectations considered in the
@@ -403,14 +403,14 @@
     for raw i/o.
 ii. Ability to represent high-memory buffers (which do not have a virtual
     address mapping in kernel address space).
-iii.Ability to represent large i/os w/o unecessarily breaking them up (i.e
+iii.Ability to represent large i/os w/o unnecessarily breaking them up (i.e
     greater than PAGE_SIZE chunks in one shot)
 iv. At the same time, ability to retain independent identity of i/os from
     different sources or i/o units requiring individual completion (e.g. for
     latency reasons)
 v.  Ability to represent an i/o involving multiple physical memory segments
     (including non-page aligned page fragments, as specified via readv/writev)
-    without unecessarily breaking it up, if the underlying device is capable of
+    without unnecessarily breaking it up, if the underlying device is capable of
     handling it.
 vi. Preferably should be based on a memory descriptor structure that can be
     passed around different types of subsystems or layers, maybe even
@@ -1013,7 +1013,7 @@
 i. Binary tree
 AS and deadline i/o schedulers use red black binary trees for disk position
 sorting and searching, and a fifo linked list for time-based searching. This
-gives good scalability and good availablility of information. Requests are
+gives good scalability and good availability of information. Requests are
 almost always dispatched in disk sort order, so a cache is kept of the next
 request in sort order to prevent binary tree lookups.
 
diff --git a/Documentation/cpu-freq/cpufreq-nforce2.txt b/Documentation/cpu-freq/cpufreq-nforce2.txt
index 9188337..babce13 100644
--- a/Documentation/cpu-freq/cpufreq-nforce2.txt
+++ b/Documentation/cpu-freq/cpufreq-nforce2.txt
@@ -1,7 +1,7 @@
 
-The cpufreq-nforce2 driver changes the FSB on nVidia nForce2 plattforms.
+The cpufreq-nforce2 driver changes the FSB on nVidia nForce2 platforms.
 
-This works better than on other plattforms, because the FSB of the CPU
+This works better than on other platforms, because the FSB of the CPU
 can be controlled independently from the PCI/AGP clock.
 
 The module has two options:
diff --git a/Documentation/cpu-hotplug.txt b/Documentation/cpu-hotplug.txt
index 4868c34..cc60d29 100644
--- a/Documentation/cpu-hotplug.txt
+++ b/Documentation/cpu-hotplug.txt
@@ -54,8 +54,8 @@
 
 ia64 and x86_64 use the number of disabled local apics in ACPI tables MADT
 to determine the number of potentially hot-pluggable cpus. The implementation
-should only rely on this to count the #of cpus, but *MUST* not rely on the
-apicid values in those tables for disabled apics. In the event BIOS doesnt
+should only rely on this to count the # of cpus, but *MUST* not rely on the
+apicid values in those tables for disabled apics. In the event BIOS doesn't
 mark such hot-pluggable cpus as disabled entries, one could use this
 parameter "additional_cpus=x" to represent those cpus in the cpu_possible_map.
 
diff --git a/Documentation/devices.txt b/Documentation/devices.txt
index 28c4f79..70690f1 100644
--- a/Documentation/devices.txt
+++ b/Documentation/devices.txt
@@ -92,7 +92,7 @@
 		  7 = /dev/full		Returns ENOSPC on write
 		  8 = /dev/random	Nondeterministic random number gen.
 		  9 = /dev/urandom	Faster, less secure random number gen.
-		 10 = /dev/aio		Asyncronous I/O notification interface
+		 10 = /dev/aio		Asynchronous I/O notification interface
 		 11 = /dev/kmsg		Writes to this come out as printk's
   1 block	RAM disk
 		  0 = /dev/ram0		First RAM disk
@@ -1093,7 +1093,7 @@
 
  55 char	DSP56001 digital signal processor
 		  0 = /dev/dsp56k	First DSP56001
- 55 block	Mylex DAC960 PCI RAID controller; eigth controller
+ 55 block	Mylex DAC960 PCI RAID controller; eighth controller
 		  0 = /dev/rd/c7d0	First disk, whole disk
 		  8 = /dev/rd/c7d1	Second disk, whole disk
 		    ...
@@ -1456,7 +1456,7 @@
 		  1 = /dev/cum1		Callout device for ttyM1
 		    ...
 
- 79 block	Compaq Intelligent Drive Array, eigth controller
+ 79 block	Compaq Intelligent Drive Array, eighth controller
 		  0 = /dev/ida/c7d0	First logical drive whole disk
 		 16 = /dev/ida/c7d1	Second logical drive whole disk
 		    ...
@@ -1900,7 +1900,7 @@
 		  1 = /dev/av1		Second A/V card
 		    ...
 
-111 block	Compaq Next Generation Drive Array, eigth controller
+111 block	Compaq Next Generation Drive Array, eighth controller
 		  0 = /dev/cciss/c7d0	First logical drive, whole disk
 		 16 = /dev/cciss/c7d1	Second logical drive, whole disk
 		    ...
diff --git a/Documentation/driver-model/platform.txt b/Documentation/driver-model/platform.txt
index 5eee3e0..9f0bc3b 100644
--- a/Documentation/driver-model/platform.txt
+++ b/Documentation/driver-model/platform.txt
@@ -1,99 +1,131 @@
 Platform Devices and Drivers
 ~~~~~~~~~~~~~~~~~~~~~~~~~~~~
+See <linux/platform_device.h> for the driver model interface to the
+platform bus:  platform_device, and platform_driver.  This pseudo-bus
+is used to connect devices on busses with minimal infrastructure,
+like those used to integrate peripherals on many system-on-chip
+processors, or some "legacy" PC interconnects; as opposed to large
+formally specified ones like PCI or USB.
+
 
 Platform devices
 ~~~~~~~~~~~~~~~~
 Platform devices are devices that typically appear as autonomous
 entities in the system. This includes legacy port-based devices and
-host bridges to peripheral buses. 
+host bridges to peripheral buses, and most controllers integrated
+into system-on-chip platforms.  What they usually have in common
+is direct addressing from a CPU bus.  Rarely, a platform_device will
+be connected through a segment of some other kind of bus; but its
+registers will still be directly addressible.
+
+Platform devices are given a name, used in driver binding, and a
+list of resources such as addresses and IRQs.
+
+struct platform_device {
+	const char	*name;
+	u32		id;
+	struct device	dev;
+	u32		num_resources;
+	struct resource	*resource;
+};
 
 
 Platform drivers
 ~~~~~~~~~~~~~~~~
-Drivers for platform devices are typically very simple and
-unstructured. Either the device was present at a particular I/O port
-and the driver was loaded, or it was not. There was no possibility
-of hotplugging or alternative discovery besides probing at a specific
-I/O address and expecting a specific response.
+Platform drivers follow the standard driver model convention, where
+discovery/enumeration is handled outside the drivers, and drivers
+provide probe() and remove() methods.  They support power management
+and shutdown notifications using the standard conventions.
+
+struct platform_driver {
+	int (*probe)(struct platform_device *);
+	int (*remove)(struct platform_device *);
+	void (*shutdown)(struct platform_device *);
+	int (*suspend)(struct platform_device *, pm_message_t state);
+	int (*suspend_late)(struct platform_device *, pm_message_t state);
+	int (*resume_early)(struct platform_device *);
+	int (*resume)(struct platform_device *);
+	struct device_driver driver;
+};
+
+Note that probe() should general verify that the specified device hardware
+actually exists; sometimes platform setup code can't be sure.  The probing
+can use device resources, including clocks, and device platform_data.
+
+Platform drivers register themselves the normal way:
+
+	int platform_driver_register(struct platform_driver *drv);
+
+Or, in common situations where the device is known not to be hot-pluggable,
+the probe() routine can live in an init section to reduce the driver's
+runtime memory footprint:
+
+	int platform_driver_probe(struct platform_driver *drv,
+			  int (*probe)(struct platform_device *))
 
 
-Other Architectures, Modern Firmware, and new Platforms
-~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
-These devices are not always at the legacy I/O ports. This is true on
-other architectures and on some modern architectures. In most cases,
-the drivers are modified to discover the devices at other well-known
-ports for the given platform. However, the firmware in these systems
-does usually know where exactly these devices reside, and in some
-cases, it's the only way of discovering them. 
+Device Enumeration
+~~~~~~~~~~~~~~~~~~
+As a rule, platform specific (and often board-specific) setup code wil
+register platform devices:
+
+	int platform_device_register(struct platform_device *pdev);
+
+	int platform_add_devices(struct platform_device **pdevs, int ndev);
+
+The general rule is to register only those devices that actually exist,
+but in some cases extra devices might be registered.  For example, a kernel
+might be configured to work with an external network adapter that might not
+be populated on all boards, or likewise to work with an integrated controller
+that some boards might not hook up to any peripherals.
+
+In some cases, boot firmware will export tables describing the devices
+that are populated on a given board.   Without such tables, often the
+only way for system setup code to set up the correct devices is to build
+a kernel for a specific target board.  Such board-specific kernels are
+common with embedded and custom systems development.
+
+In many cases, the memory and IRQ resources associated with the platform
+device are not enough to let the device's driver work.  Board setup code
+will often provide additional information using the device's platform_data
+field to hold additional information.
+
+Embedded systems frequently need one or more clocks for platform devices,
+which are normally kept off until they're actively needed (to save power).
+System setup also associates those clocks with the device, so that that
+calls to clk_get(&pdev->dev, clock_name) return them as needed.
 
 
-The Platform Bus
-~~~~~~~~~~~~~~~~
-A platform bus has been created to deal with these issues. First and
-foremost, it groups all the legacy devices under a common bus, and
-gives them a common parent if they don't already have one. 
+Device Naming and Driver Binding
+~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
+The platform_device.dev.bus_id is the canonical name for the devices.
+It's built from two components:
 
-But, besides the organizational benefits, the platform bus can also
-accommodate firmware-based enumeration. 
+    * platform_device.name ... which is also used to for driver matching.
 
+    * platform_device.id ... the device instance number, or else "-1"
+      to indicate there's only one.
 
-Device Discovery
-~~~~~~~~~~~~~~~~
-The platform bus has no concept of probing for devices. Devices
-discovery is left up to either the legacy drivers or the
-firmware. These entities are expected to notify the platform of
-devices that it discovers via the bus's add() callback:
+These are catenated, so name/id "serial"/0 indicates bus_id "serial.0", and
+"serial/3" indicates bus_id "serial.3"; both would use the platform_driver
+named "serial".  While "my_rtc"/-1 would be bus_id "my_rtc" (no instance id)
+and use the platform_driver called "my_rtc".
 
-	platform_bus.add(parent,bus_id).
+Driver binding is performed automatically by the driver core, invoking
+driver probe() after finding a match between device and driver.  If the
+probe() succeeds, the driver and device are bound as usual.  There are
+three different ways to find such a match:
 
+    - Whenever a device is registered, the drivers for that bus are
+      checked for matches.  Platform devices should be registered very
+      early during system boot.
 
-Bus IDs
-~~~~~~~
-Bus IDs are the canonical names for the devices. There is no globally
-standard addressing mechanism for legacy devices. In the IA-32 world,
-we have Pnp IDs to use, as well as the legacy I/O ports. However,
-neither tell what the device really is or have any meaning on other
-platforms. 
+    - When a driver is registered using platform_driver_register(), all
+      unbound devices on that bus are checked for matches.  Drivers
+      usually register later during booting, or by module loading.
 
-Since both PnP IDs and the legacy I/O ports (and other standard I/O
-ports for specific devices) have a 1:1 mapping, we map the
-platform-specific name or identifier to a generic name (at least
-within the scope of the kernel).
-
-For example, a serial driver might find a device at I/O 0x3f8. The
-ACPI firmware might also discover a device with PnP ID (_HID)
-PNP0501. Both correspond to the same device and should be mapped to the
-canonical name 'serial'. 
-
-The bus_id field should be a concatenation of the canonical name and
-the instance of that type of device. For example, the device at I/O
-port 0x3f8 should have a bus_id of "serial0". This places the
-responsibility of enumerating devices of a particular type up to the
-discovery mechanism. But, they are the entity that should know best
-(as opposed to the platform bus driver).
-
-
-Drivers 
-~~~~~~~
-Drivers for platform devices should have a name that is the same as
-the canonical name of the devices they support. This allows the
-platform bus driver to do simple matching with the basic data
-structures to determine if a driver supports a certain device. 
-
-For example, a legacy serial driver should have a name of 'serial' and
-register itself with the platform bus. 
-
-
-Driver Binding
-~~~~~~~~~~~~~~
-Legacy drivers assume they are bound to the device once they start up
-and probe an I/O port. Divorcing them from this will be a difficult
-process. However, that shouldn't prevent us from implementing
-firmware-based enumeration. 
-
-The firmware should notify the platform bus about devices before the
-legacy drivers have had a chance to load. Once the drivers are loaded,
-they driver model core will attempt to bind the driver to any
-previously-discovered devices. Once that has happened, it will be free
-to discover any other devices it pleases.
+    - Registering a driver using platform_driver_probe() works just like
+      using platform_driver_register(), except that the the driver won't
+      be probed later if another device registers.  (Which is OK, since
+      this interface is only for use with non-hotpluggable devices.)
 
diff --git a/Documentation/driver-model/porting.txt b/Documentation/driver-model/porting.txt
index 98b233c..92d86f7 100644
--- a/Documentation/driver-model/porting.txt
+++ b/Documentation/driver-model/porting.txt
@@ -92,7 +92,7 @@
 describing the relationship the device has to other entities. 
 
 
-- Embedd a struct device in the bus-specific device type. 
+- Embed a struct device in the bus-specific device type. 
 
 
 struct pci_dev {
diff --git a/Documentation/dvb/ci.txt b/Documentation/dvb/ci.txt
index 531239b..2ecd834 100644
--- a/Documentation/dvb/ci.txt
+++ b/Documentation/dvb/ci.txt
@@ -71,7 +71,7 @@
 The disadvantage is that the driver/hardware has to manage the rest. For
 the application programmer it would be as simple as sending/receiving an
 array to/from the CI ioctls as defined in the Linux DVB API. No changes
-have been made in the API to accomodate this feature.
+have been made in the API to accommodate this feature.
 
 
 * Why the need for another CI interface ?
@@ -102,7 +102,7 @@
 implemented by most applications. Hence this area is revisited.
 
 This CI interface is quite different in the case that it tries to
-accomodate all other CI based devices, that fall into the other categories
+accommodate all other CI based devices, that fall into the other categories.
 
 This means that this CI interface handles the EN50221 style tags in the
 Application layer only and no session management is taken care of by the
diff --git a/Documentation/eisa.txt b/Documentation/eisa.txt
index 6a099ed..60e361b 100644
--- a/Documentation/eisa.txt
+++ b/Documentation/eisa.txt
@@ -62,7 +62,7 @@
 bus_base_addr : slot 0 address on this bus
 slots	      : max slot number to probe
 force_probe   : Probe even when slot 0 is empty (no EISA mainboard)
-dma_mask      : Default DMA mask. Usualy the bridge device dma_mask.
+dma_mask      : Default DMA mask. Usually the bridge device dma_mask.
 bus_nr	      : unique bus id, set by eisa_root_register
 
 ** Driver :
diff --git a/Documentation/filesystems/adfs.txt b/Documentation/filesystems/adfs.txt
index 060abb0..9e8811f 100644
--- a/Documentation/filesystems/adfs.txt
+++ b/Documentation/filesystems/adfs.txt
@@ -3,7 +3,7 @@
 
   uid=nnn	All files in the partition will be owned by
 		user id nnn.  Default 0 (root).
-  gid=nnn	All files in the partition willbe in group
+  gid=nnn	All files in the partition will be in group
 		nnn.  Default 0 (root).
   ownmask=nnn	The permission mask for ADFS 'owner' permissions
 		will be nnn.  Default 0700.
diff --git a/Documentation/filesystems/configfs/configfs.txt b/Documentation/filesystems/configfs/configfs.txt
index c3a7afb..b34cdb5 100644
--- a/Documentation/filesystems/configfs/configfs.txt
+++ b/Documentation/filesystems/configfs/configfs.txt
@@ -209,7 +209,7 @@
 
 [struct config_group]
 
-A config_item cannot live in a vaccum.  The only way one can be created
+A config_item cannot live in a vacuum.  The only way one can be created
 is via mkdir(2) on a config_group.  This will trigger creation of a
 child item.
 
@@ -275,7 +275,7 @@
 
 [struct configfs_subsystem]
 
-A subsystem must register itself, ususally at module_init time.  This
+A subsystem must register itself, usually at module_init time.  This
 tells configfs to make the subsystem appear in the file tree.
 
 	struct configfs_subsystem {
diff --git a/Documentation/filesystems/fuse.txt b/Documentation/filesystems/fuse.txt
index a584f05..3d74477 100644
--- a/Documentation/filesystems/fuse.txt
+++ b/Documentation/filesystems/fuse.txt
@@ -111,7 +111,7 @@
 
  'waiting'
 
-  The number of requests which are waiting to be transfered to
+  The number of requests which are waiting to be transferred to
   userspace or being processed by the filesystem daemon.  If there is
   no filesystem activity and 'waiting' is non-zero, then the
   filesystem is hung or deadlocked.
@@ -136,7 +136,7 @@
 
   2) If the request is not yet sent to userspace AND the signal is not
      fatal, then an 'interrupted' flag is set for the request.  When
-     the request has been successfully transfered to userspace and
+     the request has been successfully transferred to userspace and
      this flag is set, an INTERRUPT request is queued.
 
   3) If the request is already sent to userspace, then an INTERRUPT
diff --git a/Documentation/filesystems/hpfs.txt b/Documentation/filesystems/hpfs.txt
index 33dc360..38aba03 100644
--- a/Documentation/filesystems/hpfs.txt
+++ b/Documentation/filesystems/hpfs.txt
@@ -274,7 +274,7 @@
      Fixed race-condition in buffer code - it is in all filesystems in Linux;
         when reading device (cat /dev/hda) while creating files on it, files
         could be damaged
-2.02 Woraround for bug in breada in Linux. breada could cause accesses beyond
+2.02 Workaround for bug in breada in Linux. breada could cause accesses beyond
         end of partition
 2.03 Char, block devices and pipes are correctly created
      Fixed non-crashing race in unlink (Alexander Viro)
diff --git a/Documentation/filesystems/ntfs.txt b/Documentation/filesystems/ntfs.txt
index 35f105b..13ba649 100644
--- a/Documentation/filesystems/ntfs.txt
+++ b/Documentation/filesystems/ntfs.txt
@@ -337,7 +337,7 @@
 this (note all values are in 512-byte sectors):
 
 --- cut here ---
-# Ofs Size   Raid   Log  Number Region Should Number Source  Start Taget  Start
+# Ofs Size   Raid   Log  Number Region Should Number Source  Start Target Start
 # in  of the type   type of log size   sync?  of     Device  in    Device in
 # vol volume		 params		     mirrors	     Device	  Device
 0    2056320 mirror core 2	16     nosync 2	   /dev/hda1 0   /dev/hdb1 0
@@ -599,7 +599,7 @@
 	- Major bug fixes for reading files and volumes in corner cases which
 	  were being hit by Windows 2k/XP users.
 2.1.2:
-	- Major bug fixes aleviating the hangs in statfs experienced by some
+	- Major bug fixes alleviating the hangs in statfs experienced by some
 	  users.
 2.1.1:
 	- Update handling of compressed files so people no longer get the
diff --git a/Documentation/filesystems/ocfs2.txt b/Documentation/filesystems/ocfs2.txt
index 4389c68..af6defd 100644
--- a/Documentation/filesystems/ocfs2.txt
+++ b/Documentation/filesystems/ocfs2.txt
@@ -30,7 +30,7 @@
 Features which OCFS2 does not support yet:
 	- sparse files
 	- extended attributes
-	- shared writeable mmap
+	- shared writable mmap
 	- loopback is supported, but data written will not
 	  be cluster coherent.
 	- quotas
diff --git a/Documentation/filesystems/proc.txt b/Documentation/filesystems/proc.txt
index 3355e69..72af5de 100644
--- a/Documentation/filesystems/proc.txt
+++ b/Documentation/filesystems/proc.txt
@@ -1220,9 +1220,9 @@
 you probably should increase the lower_zone_protection setting.
 
 The units of this tunable are fairly vague.  It is approximately equal
-to "megabytes".  So setting lower_zone_protection=100 will protect around 100
+to "megabytes," so setting lower_zone_protection=100 will protect around 100
 megabytes of the lowmem zone from user allocations.  It will also make
-those 100 megabytes unavaliable for use by applications and by
+those 100 megabytes unavailable for use by applications and by
 pagecache, so there is a cost.
 
 The effects of this tunable may be observed by monitoring
@@ -1538,10 +1538,10 @@
 tcp_ecn
 -------
 
-This file controls the use of the ECN bit in the IPv4 headers, this is a new
+This file controls the use of the ECN bit in the IPv4 headers. This is a new
 feature about Explicit Congestion Notification, but some routers and firewalls
-block trafic that has this bit set, so it could be necessary to echo 0 to
-/proc/sys/net/ipv4/tcp_ecn, if you want to talk to this sites. For more info
+block traffic that has this bit set, so it could be necessary to echo 0 to
+/proc/sys/net/ipv4/tcp_ecn if you want to talk to these sites. For more info
 you could read RFC2481.
 
 tcp_retrans_collapse
diff --git a/Documentation/filesystems/spufs.txt b/Documentation/filesystems/spufs.txt
index 982645a..1343d11 100644
--- a/Documentation/filesystems/spufs.txt
+++ b/Documentation/filesystems/spufs.txt
@@ -210,7 +210,7 @@
    /signal2
        The two signal notification channels of an SPU.  These  are  read-write
        files  that  operate  on  a 32 bit word.  Writing to one of these files
-       triggers an interrupt on the SPU. The  value  writting  to  the  signal
+       triggers an interrupt on the SPU.  The  value  written  to  the  signal
        files can be read from the SPU through a channel read or from host user
        space through the file.  After the value has been read by the  SPU,  it
        is  reset  to zero.  The possible operations on an open signal1 or sig-
diff --git a/Documentation/fujitsu/frv/gdbstub.txt b/Documentation/fujitsu/frv/gdbstub.txt
index 6ce5aa9..9304fb3 100644
--- a/Documentation/fujitsu/frv/gdbstub.txt
+++ b/Documentation/fujitsu/frv/gdbstub.txt
@@ -59,7 +59,7 @@
 Then build as usual, download to the board and execute. Note that if
 "Immediate activation" was selected, then the kernel will wait for GDB to
 attach. If not, then the kernel will boot immediately and GDB will have to
-interupt it or wait for an exception to occur if before doing anything with
+interrupt it or wait for an exception to occur before doing anything with
 the kernel.
 
 
diff --git a/Documentation/fujitsu/frv/kernel-ABI.txt b/Documentation/fujitsu/frv/kernel-ABI.txt
index 8b0a5fc..aaa1cec 100644
--- a/Documentation/fujitsu/frv/kernel-ABI.txt
+++ b/Documentation/fujitsu/frv/kernel-ABI.txt
@@ -156,7 +156,7 @@
 almost completely self-contained. The only external code used is the
 sprintf family of functions.
 
-Futhermore, break.S is so complicated because single-step mode does not
+Furthermore, break.S is so complicated because single-step mode does not
 switch off on entry to an exception. That means unless manually disabled,
 single-stepping will blithely go on stepping into things like interrupts.
 See gdbstub.txt for more information.
diff --git a/Documentation/ide.txt b/Documentation/ide.txt
index 0bf38ba..786c3a7 100644
--- a/Documentation/ide.txt
+++ b/Documentation/ide.txt
@@ -390,5 +390,5 @@
 Wed Apr 17 22:52:44 CEST 2002 edited by Marcin Dalecki, the current
 maintainer.
 
-Wed Aug 20 22:31:29 CEST 2003 updated ide boot uptions to current ide.c
+Wed Aug 20 22:31:29 CEST 2003 updated ide boot options to current ide.c
 comments at 2.6.0-test4 time. Maciej Soltysiak <solt@dns.toxicfilms.tv>
diff --git a/Documentation/input/amijoy.txt b/Documentation/input/amijoy.txt
index 4f0e89d..7dc4f17 100644
--- a/Documentation/input/amijoy.txt
+++ b/Documentation/input/amijoy.txt
@@ -91,8 +91,8 @@
          |   1    | M0HQ     | JOY0DAT Horizontal Clock (quadrature)   |
          |   2    | M0V      | JOY0DAT Vertical Clock                  |
          |   3    | M0VQ     | JOY0DAT Vertical Clock  (quadrature)    |
-         |   4    | M1V      | JOY1DAT Horizontall Clock               |
-         |   5    | M1VQ     | JOY1DAT Horizontall Clock (quadrature)  |
+         |   4    | M1V      | JOY1DAT Horizontal Clock                |
+         |   5    | M1VQ     | JOY1DAT Horizontal Clock (quadrature)   |
          |   6    | M1V      | JOY1DAT Vertical Clock                  |
          |   7    | M1VQ     | JOY1DAT Vertical Clock (quadrature)     |
          +--------+----------+-----------------------------------------+
diff --git a/Documentation/input/atarikbd.txt b/Documentation/input/atarikbd.txt
index 1e7e585..668f4d0 100644
--- a/Documentation/input/atarikbd.txt
+++ b/Documentation/input/atarikbd.txt
@@ -103,7 +103,7 @@
 
 5.1 Joystick Event Reporting
 
-In this mode, the ikbd generates a record whever the joystick position is
+In this mode, the ikbd generates a record whenever the joystick position is
 changed (i.e. for each opening or closing of a joystick switch or trigger).
 
 The joystick event record is two bytes of the form:
@@ -277,8 +277,8 @@
 9.7 SET MOUSE SCALE
 
     0x0C
-    X                   ; horizontal mouse ticks per internel X
-    Y                   ; vertical mouse ticks per internel Y
+    X                   ; horizontal mouse ticks per internal X
+    Y                   ; vertical mouse ticks per internal Y
 
 This command sets the scale factor for the ABSOLUTE MOUSE POSITIONING mode.
 In this mode, the specified number of mouse phase changes ('clicks') must
@@ -323,7 +323,7 @@
     0x0F
 
 This command makes the origin of the Y axis to be at the bottom of the
-logical coordinate system internel to the ikbd for all relative or absolute
+logical coordinate system internal to the ikbd for all relative or absolute
 mouse motion. This causes mouse motion toward the user to be negative in sign
 and away from the user to be positive.
 
@@ -597,8 +597,8 @@
 
 10. SCAN CODES
 
-The key scan codes return by the ikbd are chosen to simplify the
-implementaion of GSX.
+The key scan codes returned by the ikbd are chosen to simplify the
+implementation of GSX.
 
 GSX Standard Keyboard Mapping.
 
diff --git a/Documentation/input/yealink.txt b/Documentation/input/yealink.txt
index 0a8c97e..5360e43 100644
--- a/Documentation/input/yealink.txt
+++ b/Documentation/input/yealink.txt
@@ -134,7 +134,7 @@
   888888888888
   Linux Rocks!
 
-Writing to /sys/../lineX will set the coresponding LCD line.
+Writing to /sys/../lineX will set the corresponding LCD line.
  - Excess characters are ignored.
  - If less characters are written than allowed, the remaining digits are
    unchanged.
diff --git a/Documentation/ioctl/cdrom.txt b/Documentation/ioctl/cdrom.txt
index 8ec32cc..62d4af4 100644
--- a/Documentation/ioctl/cdrom.txt
+++ b/Documentation/ioctl/cdrom.txt
@@ -735,7 +735,7 @@
 	    Ok, this is where problems start.  The current interface for
 	    the CDROM_DISC_STATUS ioctl is flawed.  It makes the false
 	    assumption that CDs are all CDS_DATA_1 or all CDS_AUDIO, etc.
-	    Unfortunatly, while this is often the case, it is also
+	    Unfortunately, while this is often the case, it is also
 	    very common for CDs to have some tracks with data, and some
 	    tracks with audio.	Just because I feel like it, I declare
 	    the following to be the best way to cope.  If the CD has
diff --git a/Documentation/kbuild/makefiles.txt b/Documentation/kbuild/makefiles.txt
index 50f4edd..4b3d671 100644
--- a/Documentation/kbuild/makefiles.txt
+++ b/Documentation/kbuild/makefiles.txt
@@ -227,9 +227,9 @@
 	be included in a library, lib.a.
 	All objects listed with lib-y are combined in a single
 	library for that directory.
-	Objects that are listed in obj-y and additionaly listed in
-	lib-y will not be included in the library, since they will anyway
-	be accessible.
+	Objects that are listed in obj-y and additionally listed in
+	lib-y will not be included in the library, since they will
+	be accessible anyway.
 	For consistency, objects listed in lib-m will be included in lib.a.
 
 	Note that the same kbuild makefile may list files to be built-in
@@ -535,7 +535,7 @@
 	Host programs can be made up based on composite objects.
 	The syntax used to define composite objects for host programs is
 	similar to the syntax used for kernel objects.
-	$(<executeable>-objs) lists all objects used to link the final
+	$(<executable>-objs) lists all objects used to link the final
 	executable.
 
 	Example:
@@ -1022,7 +1022,7 @@
 	In this example, there are two possible targets, requiring different
 	options to the linker. The linker options are specified using the
 	LDFLAGS_$@ syntax - one for each potential target.
-	$(targets) are assinged all potential targets, by which kbuild knows
+	$(targets) are assigned all potential targets, by which kbuild knows
 	the targets and will:
 		1) check for commandline changes
 		2) delete target during make clean
diff --git a/Documentation/keys.txt b/Documentation/keys.txt
index 3da586b..60c665d 100644
--- a/Documentation/keys.txt
+++ b/Documentation/keys.txt
@@ -304,7 +304,7 @@
 	R	Revoked
 	D	Dead
 	Q	Contributes to user's quota
-	U	Under contruction by callback to userspace
+	U	Under construction by callback to userspace
 	N	Negative key
 
      This file must be enabled at kernel configuration time as it allows anyone
diff --git a/Documentation/laptop-mode.txt b/Documentation/laptop-mode.txt
index c487186..6f639e3 100644
--- a/Documentation/laptop-mode.txt
+++ b/Documentation/laptop-mode.txt
@@ -121,7 +121,7 @@
 MAX_AGE:
 
 Maximum time, in seconds, of hard drive spindown time that you are
-confortable with. Worst case, it's possible that you could lose this
+comfortable with. Worst case, it's possible that you could lose this
 amount of work if your battery fails while you're in laptop mode.
 
 MINIMUM_BATTERY_MINUTES:
@@ -235,7 +235,7 @@
 
 --------------------CONFIG FILE BEGIN-------------------------------------------
 # Maximum time, in seconds, of hard drive spindown time that you are
-# confortable with. Worst case, it's possible that you could lose this
+# comfortable with. Worst case, it's possible that you could lose this
 # amount of work if your battery fails you while in laptop mode.
 #MAX_AGE=600
 
@@ -350,7 +350,7 @@
 # set defaults instead:
 
 # Maximum time, in seconds, of hard drive spindown time that you are
-# confortable with. Worst case, it's possible that you could lose this
+# comfortable with. Worst case, it's possible that you could lose this
 # amount of work if your battery fails you while in laptop mode.
 MAX_AGE=${MAX_AGE:-'600'}
 
@@ -699,7 +699,7 @@
 Dax Kelson submitted this so that the ACPI acpid daemon will
 kick off the laptop_mode script and run hdparm. The part that
 automatically disables laptop mode when the battery is low was
-writen by Jan Topinski.
+written by Jan Topinski.
 
 -----------------/etc/acpi/events/ac_adapter BEGIN------------------------------
 event=ac_adapter
diff --git a/Documentation/memory-barriers.txt b/Documentation/memory-barriers.txt
index 7751704..58408dd 100644
--- a/Documentation/memory-barriers.txt
+++ b/Documentation/memory-barriers.txt
@@ -212,7 +212,7 @@
 
 	STORE *X = c, d = LOAD *X
 
-     (Loads and stores overlap if they are targetted at overlapping pieces of
+     (Loads and stores overlap if they are targeted at overlapping pieces of
      memory).
 
 And there are a number of things that _must_ or _must_not_ be assumed:
diff --git a/Documentation/networking/NAPI_HOWTO.txt b/Documentation/networking/NAPI_HOWTO.txt
index 93af3e8..fb8dc64 100644
--- a/Documentation/networking/NAPI_HOWTO.txt
+++ b/Documentation/networking/NAPI_HOWTO.txt
@@ -95,8 +95,8 @@
 		Move all to dev->poll()
 
 C) Ability to detect new work correctly.
-NAPI works by shutting down event interrupts when theres work and
-turning them on when theres none. 
+NAPI works by shutting down event interrupts when there's work and
+turning them on when there's none. 
 New packets might show up in the small window while interrupts were being 
 re-enabled (refer to appendix 2).  A packet might sneak in during the period 
 we are enabling interrupts. We only get to know about such a packet when the 
@@ -114,7 +114,7 @@
 only one CPU can pick the initial interrupt and hence the initial
 netif_rx_schedule(dev);
 - The core layer invokes devices to send packets in a round robin format.
-This implies receive is totaly lockless because of the guarantee only that 
+This implies receive is totally lockless because of the guarantee that only 
 one CPU is executing it.
 -  contention can only be the result of some other CPU accessing the rx
 ring. This happens only in close() and suspend() (when these methods
@@ -510,7 +510,7 @@
 			an interrupt will be generated */
                         goto done;
 	}
-	/* done! at least thats what it looks like ;->
+	/* done! at least that's what it looks like ;->
 	if new packets came in after our last check on status bits
 	they'll be caught by the while check and we go back and clear them 
 	since we havent exceeded our quota */
@@ -535,11 +535,11 @@
         * 1. it can race with disabling irqs in irq handler (which are done to 
 	* schedule polls)
         * 2. it can race with dis/enabling irqs in other poll threads
-        * 3. if an irq raised after the begining of the outer  beginning 
-        * loop(marked in the code above), it will be immediately
+        * 3. if an irq raised after the beginning of the outer beginning 
+        * loop (marked in the code above), it will be immediately
         * triggered here.
         *
-        * Summarizing: the logic may results in some redundant irqs both
+        * Summarizing: the logic may result in some redundant irqs both
         * due to races in masking and due to too late acking of already
         * processed irqs. The good news: no events are ever lost.
         */
@@ -601,7 +601,7 @@
 	
 5) dev->close() and dev->suspend() issues
 ==========================================
-The driver writter neednt worry about this. The top net layer takes
+The driver writer needn't worry about this; the top net layer takes
 care of it.
 
 6) Adding new Stats to /proc 
@@ -622,9 +622,9 @@
 packets fast enough i.e send a pause only when you run out of rx buffers.
 Note FC in itself is a good solution but we have found it to not be
 much of a commodity feature (both in NICs and switches) and hence falls
-under the same category as using NIC based mitigation. Also experiments
-indicate that its much harder to resolve the resource allocation
-issue (aka lazy receiving that NAPI offers) and hence quantify its usefullness
+under the same category as using NIC based mitigation. Also, experiments
+indicate that it's much harder to resolve the resource allocation
+issue (aka lazy receiving that NAPI offers) and hence quantify its usefulness
 proved harder. In any case, FC works even better with NAPI but is not
 necessary.
 
@@ -678,10 +678,10 @@
 CSR5 bit of interest is only the rx status. 
 If you look at the last if statement: 
 you just finished grabbing all the packets from the rx ring .. you check if
-status bit says theres more packets just in ... it says none; you then
+status bit says there are more packets just in ... it says none; you then
 enable rx interrupts again; if a new packet just came in during this check,
 we are counting that CSR5 will be set in that small window of opportunity
-and that by re-enabling interrupts, we would actually triger an interrupt
+and that by re-enabling interrupts, we would actually trigger an interrupt
 to register the new packet for processing.
 
 [The above description nay be very verbose, if you have better wording 
diff --git a/Documentation/networking/cs89x0.txt b/Documentation/networking/cs89x0.txt
index 6489647..6387d3d 100644
--- a/Documentation/networking/cs89x0.txt
+++ b/Documentation/networking/cs89x0.txt
@@ -248,7 +248,7 @@
    with device probing.  To avoid this behaviour, add one
    to the `io=' module parameter.  This doesn't actually change
    the I/O address, but it is a flag to tell the driver
-   topartially initialise the hardware before trying to
+   to partially initialise the hardware before trying to
    identify the card.  This could be dangerous if you are
    not sure that there is a cs89x0 card at the provided address.
 
@@ -620,8 +620,8 @@
                                                 12       Mouse (PS/2)                              
 Memory Address  Device                          13       Math Coprocessor
 --------------  ---------------------           14       Hard Disk controller
-A000-BFFF	EGA Graphics Adpater
-A000-C7FF	VGA Graphics Adpater
+A000-BFFF	EGA Graphics Adapter
+A000-C7FF	VGA Graphics Adapter
 B000-BFFF	Mono Graphics Adapter
 B800-BFFF	Color Graphics Adapter
 E000-FFFF	AT BIOS
diff --git a/Documentation/networking/iphase.txt b/Documentation/networking/iphase.txt
index 493203a..55eac4a 100644
--- a/Documentation/networking/iphase.txt
+++ b/Documentation/networking/iphase.txt
@@ -81,7 +81,7 @@
     1M. The RAM size decides the number of buffers and buffer size. The default 
     size and number of buffers are set as following: 
 
-          Totol    Rx RAM   Tx RAM   Rx Buf   Tx Buf   Rx buf   Tx buf
+          Total    Rx RAM   Tx RAM   Rx Buf   Tx Buf   Rx buf   Tx buf
          RAM size   size     size     size     size      cnt      cnt
          --------  ------   ------   ------   ------   ------   ------
            128K      64K      64K      10K      10K       6        6
diff --git a/Documentation/networking/packet_mmap.txt b/Documentation/networking/packet_mmap.txt
index 12a008a..5a232d9 100644
--- a/Documentation/networking/packet_mmap.txt
+++ b/Documentation/networking/packet_mmap.txt
@@ -284,7 +284,7 @@
 -------------------
 
 If you check the source code you will see that what I draw here as a frame
-is not only the link level frame. At the begining of each frame there is a 
+is not only the link level frame. At the beginning of each frame there is a 
 header called struct tpacket_hdr used in PACKET_MMAP to hold link level's frame
 meta information like timestamp. So what we draw here a frame it's really 
 the following (from include/linux/if_packet.h):
diff --git a/Documentation/networking/pktgen.txt b/Documentation/networking/pktgen.txt
index c8eee23..c6cf4a3 100644
--- a/Documentation/networking/pktgen.txt
+++ b/Documentation/networking/pktgen.txt
@@ -63,8 +63,8 @@
 Result: OK: 13101142(c12220741+d880401) usec, 10000000 (60byte,0frags)
   763292pps 390Mb/sec (390805504bps) errors: 39664
 
-Confguring threads and devices
-==============================
+Configuring threads and devices
+================================
 This is done via the /proc interface easiest done via pgset in the scripts
 
 Examples:
@@ -116,7 +116,7 @@
 					 there must be no spaces between the
 					 arguments. Leading zeros are required.
 					 Do not set the bottom of stack bit,
-					 thats done automatically. If you do
+					 that's done automatically. If you do
 					 set the bottom of stack bit, that
 					 indicates that you want to randomly
 					 generate that address and the flag
diff --git a/Documentation/networking/proc_net_tcp.txt b/Documentation/networking/proc_net_tcp.txt
index 59cb915..5e21f7c 100644
--- a/Documentation/networking/proc_net_tcp.txt
+++ b/Documentation/networking/proc_net_tcp.txt
@@ -25,7 +25,7 @@
 
    1000        0 54165785 4 cd1e6040 25 4 27 3 -1
     |          |    |     |    |     |  | |  | |--> slow start size threshold, 
-    |          |    |     |    |     |  | |  |      or -1 if the treshold
+    |          |    |     |    |     |  | |  |      or -1 if the threshold
     |          |    |     |    |     |  | |  |      is >= 0xFFFF
     |          |    |     |    |     |  | |  |----> sending congestion window
     |          |    |     |    |     |  | |-------> (ack.quick<<1)|ack.pingpong
diff --git a/Documentation/networking/sk98lin.txt b/Documentation/networking/sk98lin.txt
index 4e1cc74..8590a95 100644
--- a/Documentation/networking/sk98lin.txt
+++ b/Documentation/networking/sk98lin.txt
@@ -346,7 +346,7 @@
       depending on the load of the system. If the driver detects that the
       system load is too high, the driver tries to shield the system against 
       too much network load by enabling interrupt moderation. If - at a later
-      time - the CPU utilizaton decreases again (or if the network load is 
+      time - the CPU utilization decreases again (or if the network load is 
       negligible) the interrupt moderation will automatically be disabled.
 
 Interrupt moderation should be used when the driver has to handle one or more
diff --git a/Documentation/networking/slicecom.txt b/Documentation/networking/slicecom.txt
index 2f04c92..32d3b91 100644
--- a/Documentation/networking/slicecom.txt
+++ b/Documentation/networking/slicecom.txt
@@ -126,7 +126,7 @@
 
 Though the options below are to be set on a single interface, they apply to the
 whole board. The restriction, to use them on 'UP' interfaces, is because the 
-command sequence below could lead to unpredicable results.
+command sequence below could lead to unpredictable results.
 
 	# echo 0        >boardnum
 	# echo internal >clock_source
diff --git a/Documentation/networking/wan-router.txt b/Documentation/networking/wan-router.txt
index 0cf6541..653978d 100644
--- a/Documentation/networking/wan-router.txt
+++ b/Documentation/networking/wan-router.txt
@@ -412,7 +412,7 @@
 
 beta3-2.1.4 Jul 2000		o X25 M_BIT Problem fix.
 				o Added the Multi-Port PPP
-				  Updated utilites for the Multi-Port PPP.
+				  Updated utilities for the Multi-Port PPP.
 
 2.1.4	Aut 2000
 				o In X25API:
@@ -444,13 +444,13 @@
 					
 				o Cpipemon
 					- Added set FT1 commands to the cpipemon. Thus CSU/DSU
-					  configuraiton can be performed using cpipemon.
+					  configuration can be performed using cpipemon.
 					  All systems that cannot run cfgft1 GUI utility should
 					  use cpipemon to configure the on board CSU/DSU.
 
 
 				o Keyboard Led Monitor/Debugger
-					- A new utilty /usr/sbin/wpkbdmon uses keyboard leds
+					- A new utility /usr/sbin/wpkbdmon uses keyboard leds
 					  to convey operational statistic information of the 
 					  Sangoma WANPIPE cards.
 					NUM_LOCK    = Line State  (On=connected,    Off=disconnected)
@@ -464,7 +464,7 @@
 					- Appropriate number of devices are dynamically loaded 
 					  based on the number of Sangoma cards found.
 
-					  Note: The kernel configuraiton option 
+					  Note: The kernel configuration option 
 						CONFIG_WANPIPE_CARDS has been taken out.
 					
 				o Fixed the Frame Relay and Chdlc network interfaces so they are
diff --git a/Documentation/pnp.txt b/Documentation/pnp.txt
index 9ff966b..28037aa 100644
--- a/Documentation/pnp.txt
+++ b/Documentation/pnp.txt
@@ -184,7 +184,7 @@
 Please note that the character 'X' can be used as a wild card in the function
 portion (last four characters).
 ex:
-	/* Unkown PnP modems */
+	/* Unknown PnP modems */
 	{	"PNPCXXX",		UNKNOWN_DEV	},
 
 Supported PnP card IDs can optionally be defined.
diff --git a/Documentation/power/pci.txt b/Documentation/power/pci.txt
index 24edf25..c750f9f 100644
--- a/Documentation/power/pci.txt
+++ b/Documentation/power/pci.txt
@@ -153,7 +153,7 @@
 	events, which is implicit if it doesn't even support it in the first
 	place).
 
-	Note that the PMC Register in the device's PM Capabilties has a bitmask
+	Note that the PMC Register in the device's PM Capabilities has a bitmask
 	of the states it supports generating PME# from. D3hot is bit 3 and
 	D3cold is bit 4. So, while a value of 4 as the state may not seem
 	semantically correct, it is. 
@@ -268,7 +268,7 @@
 some non-standard way of generating a wake event on sleep.)
 
 Bits 15:11 of the PMC (Power Mgmt Capabilities) Register in a device's
-PM Capabilties describe what power states the device supports generating a 
+PM Capabilities describe what power states the device supports generating a 
 wake event from:
 
 +------------------+
diff --git a/Documentation/power/states.txt b/Documentation/power/states.txt
index 3e5e5d3..0931a33 100644
--- a/Documentation/power/states.txt
+++ b/Documentation/power/states.txt
@@ -62,7 +62,7 @@
 inconvenience, this method requires minimal work by the kernel, since
 the firmware will also handle restoring memory contents on resume. 
 
-If the kernel is responsible for persistantly saving state, a mechanism 
+If the kernel is responsible for persistently saving state, a mechanism
 called 'swsusp' (Swap Suspend) is used to write memory contents to
 free swap space. swsusp has some restrictive requirements, but should
 work in most cases. Some, albeit outdated, documentation can be found
diff --git a/Documentation/power/swsusp.txt b/Documentation/power/swsusp.txt
index 9ea2208..e635e6f 100644
--- a/Documentation/power/swsusp.txt
+++ b/Documentation/power/swsusp.txt
@@ -153,7 +153,7 @@
 
 If the thread is needed for writing the image to storage, you should
 instead set the PF_NOFREEZE process flag when creating the thread (and
-be very carefull).
+be very careful).
 
 
 Q: What is the difference between "platform", "shutdown" and
diff --git a/Documentation/powerpc/booting-without-of.txt b/Documentation/powerpc/booting-without-of.txt
index 27b457c..4ac2d64 100644
--- a/Documentation/powerpc/booting-without-of.txt
+++ b/Documentation/powerpc/booting-without-of.txt
@@ -33,13 +33,13 @@
                          - Change version 16 format to always align
                            property data to 4 bytes. Since tokens are
                            already aligned, that means no specific
-                           required alignement between property size
+                           required alignment between property size
                            and property data. The old style variable
                            alignment would make it impossible to do
                            "simple" insertion of properties using
                            memove (thanks Milton for
                            noticing). Updated kernel patch as well
-			 - Correct a few more alignement constraints
+			 - Correct a few more alignment constraints
 			 - Add a chapter about the device-tree
                            compiler and the textural representation of
                            the tree that can be "compiled" by dtc.
@@ -854,7 +854,7 @@
       console device if any. Typically, if you have serial devices on
       your board, you may want to put the full path to the one set as
       the default console in the firmware here, for the kernel to pick
-      it up as it's own default console. If you look at the funciton
+      it up as its own default console. If you look at the function
       set_preferred_console() in arch/ppc64/kernel/setup.c, you'll see
       that the kernel tries to find out the default console and has
       knowledge of various types like 8250 serial ports. You may want
@@ -1124,7 +1124,7 @@
 	- interrupt-parent : contains the phandle of the interrupt
           controller which handles interrupts for this device
 	- interrupts : a list of tuples representing the interrupt
-          number and the interrupt sense and level for each interupt
+          number and the interrupt sense and level for each interrupt
           for this device.
 
 This information is used by the kernel to build the interrupt table
diff --git a/Documentation/robust-futex-ABI.txt b/Documentation/robust-futex-ABI.txt
index 8529a17..535f69f 100644
--- a/Documentation/robust-futex-ABI.txt
+++ b/Documentation/robust-futex-ABI.txt
@@ -170,7 +170,7 @@
  1) the 'head' pointer or an subsequent linked list pointer
     is not a valid address of a user space word
  2) the calculated location of the 'lock word' (address plus
-    'offset') is not the valud address of a 32 bit user space
+    'offset') is not the valid address of a 32 bit user space
     word
  3) if the list contains more than 1 million (subject to
     future kernel configuration changes) elements.
diff --git a/Documentation/robust-futexes.txt b/Documentation/robust-futexes.txt
index 76e8064..0a9446a 100644
--- a/Documentation/robust-futexes.txt
+++ b/Documentation/robust-futexes.txt
@@ -181,7 +181,7 @@
 So there is virtually zero overhead for tasks not using robust futexes,
 and even for robust futex users, there is only one extra syscall per
 thread lifetime, and the cleanup operation, if it happens, is fast and
-straightforward. The kernel doesnt have any internal distinction between
+straightforward. The kernel doesn't have any internal distinction between
 robust and normal futexes.
 
 If a futex is found to be held at exit time, the kernel sets the
diff --git a/Documentation/s390/crypto/crypto-API.txt b/Documentation/s390/crypto/crypto-API.txt
index 29dee79..41a8b07 100644
--- a/Documentation/s390/crypto/crypto-API.txt
+++ b/Documentation/s390/crypto/crypto-API.txt
@@ -75,8 +75,8 @@
 
 - SHA1 Digest Algorithm [sha1 -> sha1_z990]
 - DES Encrypt/Decrypt Algorithm (64bit key) [des -> des_z990]
-- Tripple DES Encrypt/Decrypt Algorithm (128bit key) [des3_ede128 -> des_z990]
-- Tripple DES Encrypt/Decrypt Algorithm (192bit key) [des3_ede -> des_z990]
+- Triple DES Encrypt/Decrypt Algorithm (128bit key) [des3_ede128 -> des_z990]
+- Triple DES Encrypt/Decrypt Algorithm (192bit key) [des3_ede -> des_z990]
 
 In order to load, for example, the sha1_z990 module when the sha1 algorithm is
 requested (see 3.2.) add 'alias sha1 sha1_z990' to /etc/modprobe.conf.
diff --git a/Documentation/scsi/aic79xx.txt b/Documentation/scsi/aic79xx.txt
index 904d49e..6aa9a89 100644
--- a/Documentation/scsi/aic79xx.txt
+++ b/Documentation/scsi/aic79xx.txt
@@ -127,7 +127,7 @@
         - Correct a reference to free'ed memory during controller
           shutdown.
         - Reset the bus on an SE->LVD change.  This is required
-          to reset our transcievers.
+          to reset our transceivers.
 
    1.3.5 (March 24th, 2003)
         - Fix a few register window mode bugs.
@@ -169,7 +169,7 @@
    1.3.0 (January 21st, 2003)
         - Full regression testing for all U320 products completed.
         - Added abort and target/lun reset error recovery handler and
-          interrupt coalessing.
+          interrupt coalescing.
 
    1.2.0 (November 14th, 2002)
         - Added support for Domain Validation
diff --git a/Documentation/scsi/aic7xxx_old.txt b/Documentation/scsi/aic7xxx_old.txt
index c92f447..05667e7 100644
--- a/Documentation/scsi/aic7xxx_old.txt
+++ b/Documentation/scsi/aic7xxx_old.txt
@@ -256,7 +256,7 @@
 	      En/Disable High Byte LVD Termination
 
 	The upper 2 bits that deal with LVD termination only apply to Ultra2
-	controllers.  Futhermore, due to the current Ultra2 controller
+	controllers.  Furthermore, due to the current Ultra2 controller
 	designs, these bits are tied together such that setting either bit
 	enables both low and high byte LVD termination.  It is not possible
 	to only set high or low byte LVD termination in this manner.  This is
@@ -436,7 +436,7 @@
     the commas to periods, insmod won't interpret this as more than one
     string and write junk into our binary image.  I consider it a bug in
     the insmod program that even if you wrap your string in quotes (quotes
-    that pass the shell mind you and that insmod sees) it still treates
+    that pass the shell mind you and that insmod sees) it still treats
     a comma inside of those quotes as starting a new variable, resulting
     in memory scribbles if you don't switch the commas to periods.
 
diff --git a/Documentation/scsi/ibmmca.txt b/Documentation/scsi/ibmmca.txt
index 35f6b8e..9707941 100644
--- a/Documentation/scsi/ibmmca.txt
+++ b/Documentation/scsi/ibmmca.txt
@@ -461,7 +461,7 @@
       This needs the RD-Bit to be disabled on IM_OTHER_SCSI_CMD_CMD which 
       allows data to be written from the system to the device. It is a
       necessary step to be allowed to set blocksize of SCSI-tape-drives and 
-      the tape-speed, whithout confusing the SCSI-Subsystem.
+      the tape-speed, without confusing the SCSI-Subsystem.
    2) The recognition of a tape is included in the check_devices routine.
       This is done by checking for TYPE_TAPE, that is already defined in
       the kernel-scsi-environment. The markup of a tape is done in the 
@@ -710,8 +710,8 @@
       of troubles with some controllers and after I wanted to apply some
       extensions, it jumped out in the same situation, on my w/cache, as like 
       on D. Weinehalls' Model 56, having integrated SCSI. This gave me the 
-      descissive hint to move the code-part out and declare it global. Now,
-      it seems to work by far much better an more stable. Let us see, what
+      decisive hint to move the code-part out and declare it global. Now
+      it seems to work far better and more stable. Let us see what
       the world thinks of it...
    3) By the way, only Sony DAT-drives seem to show density code 0x13. A
       test with a HP drive gave right results, so the problem is vendor-
@@ -822,10 +822,10 @@
    A long period of collecting bugreports from all corners of the world
    now lead to the following corrections to the code:
    1) SCSI-2 F/W support crashed with a COMMAND ERROR. The reason for this 
-      was, that it is possible to disbale Fast-SCSI for the external bus.
-      The feature-control command, where this crash appeared regularly tried
+      was that it is possible to disable Fast-SCSI for the external bus.
+      The feature-control command, where this crash appeared regularly, tried
       to set the maximum speed of 10MHz synchronous transfer speed and that
-      reports a COMMAND ERROR, if external bus Fast-SCSI is disabled. Now,
+      reports a COMMAND ERROR if external bus Fast-SCSI is disabled. Now,
       the feature-command probes down from maximum speed until the adapter 
       stops to complain, which is at the same time the maximum possible
       speed selected in the reference program. So, F/W external can run at
@@ -920,7 +920,7 @@
       completed in such a way, that they are now completely conform to the
       demands in the technical description of IBM. Main candidates were the
       DEVICE_INQUIRY, REQUEST_SENSE and DEVICE_CAPACITY commands. They must
-      be tranferred by bypassing the internal command buffer of the adapter
+      be transferred by bypassing the internal command buffer of the adapter
       or else the response can be a random result. GET_POS_INFO would be more
       safe in usage, if one could use the SUPRESS_EXCEPTION_SHORT, but this
       is not allowed by the technical references of IBM. (Sorry, folks, the
diff --git a/Documentation/scsi/in2000.txt b/Documentation/scsi/in2000.txt
index 80f1040..c3e2a90 100644
--- a/Documentation/scsi/in2000.txt
+++ b/Documentation/scsi/in2000.txt
@@ -24,7 +24,7 @@
 UPDATE NEWS: version 1.31 - 6 Jul 97
 
    Fixed a bug that caused incorrect SCSI status bytes to be
-   returned from commands sent to LUN's greater than 0. This
+   returned from commands sent to LUNs greater than 0. This
    means that CDROM changers work now! Fixed a bug in the
    handling of command-line arguments when loaded as a module.
    Also put all the header data in in2000.h where it belongs.
diff --git a/Documentation/scsi/libsas.txt b/Documentation/scsi/libsas.txt
index 9e2078b..aa54f54 100644
--- a/Documentation/scsi/libsas.txt
+++ b/Documentation/scsi/libsas.txt
@@ -393,7 +393,7 @@
 	task_proto -- _one_ of enum sas_proto
 	scatter -- pointer to scatter gather list array
 	num_scatter -- number of elements in scatter
-	total_xfer_len -- total number of bytes expected to be transfered
+	total_xfer_len -- total number of bytes expected to be transferred
 	data_dir -- PCI_DMA_...
 	task_done -- callback when the task has finished execution
 };
diff --git a/Documentation/scsi/ncr53c8xx.txt b/Documentation/scsi/ncr53c8xx.txt
index 58ad8db..caf10b1 100644
--- a/Documentation/scsi/ncr53c8xx.txt
+++ b/Documentation/scsi/ncr53c8xx.txt
@@ -115,7 +115,7 @@
 
           ftp://ftp.symbios.com/
 
-Usefull SCSI tools written by Eric Youngdale are available at tsx-11:
+Useful SCSI tools written by Eric Youngdale are available at tsx-11:
 
           ftp://tsx-11.mit.edu/pub/linux/ALPHA/scsi/scsiinfo-X.Y.tar.gz
           ftp://tsx-11.mit.edu/pub/linux/ALPHA/scsi/scsidev-X.Y.tar.gz
diff --git a/Documentation/scsi/scsi-changer.txt b/Documentation/scsi/scsi-changer.txt
index d74bbd2..032399b 100644
--- a/Documentation/scsi/scsi-changer.txt
+++ b/Documentation/scsi/scsi-changer.txt
@@ -88,7 +88,7 @@
 device [ try "dmesg" if you don't see anything ] and should show up in
 /proc/devices. If not....  some changers use ID ? / LUN 0 for the
 device and ID ? / LUN 1 for the robot mechanism. But Linux does *not*
-look for LUN's other than 0 as default, becauce there are to many
+look for LUNs other than 0 as default, because there are too many
 broken devices. So you can try:
 
   1) echo "scsi add-single-device 0 0 ID 1" > /proc/scsi/scsi
@@ -107,7 +107,7 @@
 strings then.
 
 You can display these messages with the dmesg command (or check the
-logfiles).  If you email me some question becauce of a problem with the
+logfiles).  If you email me some question because of a problem with the
 driver, please include these messages.
 
 
diff --git a/Documentation/scsi/scsi_eh.txt b/Documentation/scsi/scsi_eh.txt
index b964eef..7acbebb 100644
--- a/Documentation/scsi/scsi_eh.txt
+++ b/Documentation/scsi/scsi_eh.txt
@@ -75,7 +75,7 @@
 
  - otherwise
 	scsi_eh_scmd_add(scmd, 0) is invoked for the command.  See
-	[1-3] for details of this funciton.
+	[1-3] for details of this function.
 
 
 [1-2-2] Completing a scmd w/ timeout
diff --git a/Documentation/scsi/st.txt b/Documentation/scsi/st.txt
index 5ff65b1..3c12422 100644
--- a/Documentation/scsi/st.txt
+++ b/Documentation/scsi/st.txt
@@ -261,7 +261,7 @@
 used instead of the equal mark. The definition is prepended by the
 string st=. Here is an example:
 
-	st=buffer_kbs:64,write_threhold_kbs:60
+	st=buffer_kbs:64,write_threshold_kbs:60
 
 The following syntax used by the old kernel versions is also supported:
 
diff --git a/Documentation/scsi/sym53c8xx_2.txt b/Documentation/scsi/sym53c8xx_2.txt
index 26c8a08..2c1745a 100644
--- a/Documentation/scsi/sym53c8xx_2.txt
+++ b/Documentation/scsi/sym53c8xx_2.txt
@@ -609,7 +609,7 @@
 be sure I will receive it.  Obviously, a bug in the driver code is
 possible.
 
-  My cyrrent email address: Gerard Roudier <groudier@free.fr>
+  My current email address: Gerard Roudier <groudier@free.fr>
 
 Allowing disconnections is important if you use several devices on
 your SCSI bus but often causes problems with buggy devices.
diff --git a/Documentation/sharedsubtree.txt b/Documentation/sharedsubtree.txt
index 2d8f403..ccf1ceb 100644
--- a/Documentation/sharedsubtree.txt
+++ b/Documentation/sharedsubtree.txt
@@ -942,13 +942,13 @@
 	->mnt_slave
 	->mnt_master
 
-	->mnt_share links togather all the mount to/from which this vfsmount
+	->mnt_share links together all the mount to/from which this vfsmount
 		send/receives propagation events.
 
 	->mnt_slave_list links all the mounts to which this vfsmount propagates
 		to.
 
-	->mnt_slave links togather all the slaves that its master vfsmount
+	->mnt_slave links together all the slaves that its master vfsmount
 		propagates to.
 
 	->mnt_master points to the master vfsmount from which this vfsmount
diff --git a/Documentation/sound/alsa/ALSA-Configuration.txt b/Documentation/sound/alsa/ALSA-Configuration.txt
index 3472d9c..9fef210 100644
--- a/Documentation/sound/alsa/ALSA-Configuration.txt
+++ b/Documentation/sound/alsa/ALSA-Configuration.txt
@@ -955,7 +955,7 @@
 		  dmx6fire, dsp24, dsp24_value, dsp24_71, ez8,
 		  phase88, mediastation
     omni	- Omni I/O support for MidiMan M-Audio Delta44/66
-    cs8427_timeout - reset timeout for the CS8427 chip (S/PDIF transciever)
+    cs8427_timeout - reset timeout for the CS8427 chip (S/PDIF transceiver)
                      in msec resolution, default value is 500 (0.5 sec)
 
     This module supports multiple cards and autoprobe. Note: The consumer part
diff --git a/Documentation/sound/alsa/Audigy-mixer.txt b/Documentation/sound/alsa/Audigy-mixer.txt
index 5132fd9..7f10dc6 100644
--- a/Documentation/sound/alsa/Audigy-mixer.txt
+++ b/Documentation/sound/alsa/Audigy-mixer.txt
@@ -6,7 +6,7 @@
 
 The EMU10K2 chips have a DSP part which can be programmed to support 
 various ways of sample processing, which is described here.
-(This acticle does not deal with the overall functionality of the 
+(This article does not deal with the overall functionality of the 
 EMU10K2 chips. See the manuals section for further details.)
 
 The ALSA driver programs this portion of chip by default code
diff --git a/Documentation/sound/alsa/SB-Live-mixer.txt b/Documentation/sound/alsa/SB-Live-mixer.txt
index 651adaf..f5639d4 100644
--- a/Documentation/sound/alsa/SB-Live-mixer.txt
+++ b/Documentation/sound/alsa/SB-Live-mixer.txt
@@ -5,7 +5,7 @@
 
 The EMU10K1 chips have a DSP part which can be programmed to support
 various ways of sample processing, which is described here.
-(This acticle does not deal with the overall functionality of the 
+(This article does not deal with the overall functionality of the 
 EMU10K1 chips. See the manuals section for further details.)
 
 The ALSA driver programs this portion of chip by default code
diff --git a/Documentation/stable_kernel_rules.txt b/Documentation/stable_kernel_rules.txt
index 02a4812..c815c52 100644
--- a/Documentation/stable_kernel_rules.txt
+++ b/Documentation/stable_kernel_rules.txt
@@ -50,7 +50,7 @@
    Contact the kernel security team for more details on this procedure.
 
 
-Review committe:
+Review committee:
 
  - This is made up of a number of kernel developers who have volunteered for
    this task, and a few that haven't.
diff --git a/Documentation/sysctl/fs.txt b/Documentation/sysctl/fs.txt
index 5c3a519..aa986a3 100644
--- a/Documentation/sysctl/fs.txt
+++ b/Documentation/sysctl/fs.txt
@@ -146,7 +146,7 @@
 	readable by root only. This allows the end user to remove
 	such a dump but not access it directly. For security reasons
 	core dumps in this mode will not overwrite one another or
-	other files. This mode is appropriate when adminstrators are
+	other files. This mode is appropriate when administrators are
 	attempting to debug problems in a normal environment.
 
 ==============================================================
diff --git a/Documentation/sysctl/vm.txt b/Documentation/sysctl/vm.txt
index 20d0d79..e96a341 100644
--- a/Documentation/sysctl/vm.txt
+++ b/Documentation/sysctl/vm.txt
@@ -129,7 +129,7 @@
 
 zone_reclaim_mode:
 
-Zone_reclaim_mode allows to set more or less agressive approaches to
+Zone_reclaim_mode allows someone to set more or less aggressive approaches to
 reclaim memory when a zone runs out of memory. If it is set to zero then no
 zone reclaim occurs. Allocations will be satisfied from other zones / nodes
 in the system.
diff --git a/Documentation/uml/UserModeLinux-HOWTO.txt b/Documentation/uml/UserModeLinux-HOWTO.txt
index b60590e..628013f 100644
--- a/Documentation/uml/UserModeLinux-HOWTO.txt
+++ b/Documentation/uml/UserModeLinux-HOWTO.txt
@@ -1477,7 +1477,7 @@
 
 
 
-  Making it world-writeable looks bad, but it seems not to be
+  Making it world-writable looks bad, but it seems not to be
   exploitable as a security hole.  However, it does allow anyone to cre-
   ate useless tap devices (useless because they can't configure them),
   which is a DOS attack.  A somewhat more secure alternative would to be
diff --git a/Documentation/usb/hiddev.txt b/Documentation/usb/hiddev.txt
index 6a79075..6e8c9f1 100644
--- a/Documentation/usb/hiddev.txt
+++ b/Documentation/usb/hiddev.txt
@@ -8,7 +8,7 @@
 examples for this are power devices (especially uninterruptable power
 supplies) and monitor control on higher end monitors.
 
-To support these disparite requirements, the Linux USB system provides
+To support these disparate requirements, the Linux USB system provides
 HID events to two separate interfaces:
 * the input subsystem, which converts HID events into normal input
 device interfaces (such as keyboard, mouse and joystick) and a
diff --git a/Documentation/usb/rio.txt b/Documentation/usb/rio.txt
index ab21db4..aee715a 100644
--- a/Documentation/usb/rio.txt
+++ b/Documentation/usb/rio.txt
@@ -24,10 +24,10 @@
 inconsequential.
 
 It seems that the Rio has a problem when sending .mp3 with low batteries.
-I suggest when the batteries are low and want to transfer stuff that you
+I suggest when the batteries are low and you want to transfer stuff that you
 replace it with a fresh one. In my case, what happened is I lost two 16kb
 blocks (they are no longer usable to store information to it). But I don't
-know if thats normal or not. It could simply be a problem with the flash 
+know if that's normal or not; it could simply be a problem with the flash 
 memory.
 
 In an extreme case, I left my Rio playing overnight and the batteries wore 
diff --git a/Documentation/usb/usb-serial.txt b/Documentation/usb/usb-serial.txt
index 50436e1..d61f6e7 100644
--- a/Documentation/usb/usb-serial.txt
+++ b/Documentation/usb/usb-serial.txt
@@ -175,7 +175,7 @@
   
   Current status:
     The USA-18X, USA-28X, USA-19, USA-19W and USA-49W are supported and
-    have been pretty throughly tested at various baud rates with 8-N-1
+    have been pretty thoroughly tested at various baud rates with 8-N-1
     character settings.  Other character lengths and parity setups are
     presently untested.
 
@@ -253,7 +253,7 @@
 	together without hacking the adapter to set the line high.
 
 	The driver is smp safe.  Performance with the driver is rather low when using
-	it for transfering files.  This is being worked on, but I would be willing to
+	it for transferring files.  This is being worked on, but I would be willing to
 	accept patches.  An urb queue or packet buffer would likely fit the bill here.
 
 	If you have any questions, problems, patches, feature requests, etc. you can
@@ -297,7 +297,7 @@
       Parity       N,E,O,M,S
       Handshake    None, Software (XON/XOFF), Hardware (CTSRTS,CTSDTR)*
       Break        Set and clear
-      Line contrl  Input/Output query and control **
+      Line control Input/Output query and control **
 
       *  Hardware input flow control is only enabled for firmware
          levels above 2.06.  Read source code comments describing Belkin
@@ -309,7 +309,7 @@
          automatic hardware flow control.
 
   TO DO List:
-    -- Add true modem contol line query capability.  Currently tracks the
+    -- Add true modem control line query capability.  Currently tracks the
        states reported by the interrupt and the states requested.
     -- Add error reporting back to application for UART error conditions.
     -- Add support for flush ioctls.
diff --git a/Documentation/watchdog/watchdog-api.txt b/Documentation/watchdog/watchdog-api.txt
index 7e8ae83..8d16f6f 100644
--- a/Documentation/watchdog/watchdog-api.txt
+++ b/Documentation/watchdog/watchdog-api.txt
@@ -214,7 +214,7 @@
 
 Finally the SETOPTIONS ioctl can be used to control some aspects of
 the cards operation; right now the pcwd driver is the only one
-supporting thiss ioctl.
+supporting this ioctl.
 
     int options = 0;
     ioctl(fd, WDIOC_SETOPTIONS, options);
diff --git a/MAINTAINERS b/MAINTAINERS
index e182992..846e77a 100644
--- a/MAINTAINERS
+++ b/MAINTAINERS
@@ -155,16 +155,16 @@
 S:	Maintained
 
 9P FILE SYSTEM
-P:      Eric Van Hensbergen
-M:      ericvh@gmail.com
-P:      Ron Minnich
-M:      rminnich@lanl.gov
-P:      Latchesar Ionkov
-M:      lucho@ionkov.net
-L:      v9fs-developer@lists.sourceforge.net
-W:      http://v9fs.sf.net
-T:      git kernel.org:/pub/scm/linux/kernel/ericvh/v9fs.git
-S:      Maintained
+P:	Eric Van Hensbergen
+M:	ericvh@gmail.com
+P:	Ron Minnich
+M:	rminnich@lanl.gov
+P:	Latchesar Ionkov
+M:	lucho@ionkov.net
+L:	v9fs-developer@lists.sourceforge.net
+W:	http://v9fs.sf.net
+T:	git kernel.org:/pub/scm/linux/kernel/ericvh/v9fs.git
+S:	Maintained
 
 A2232 SERIAL BOARD DRIVER
 P:	Enver Haase
@@ -290,8 +290,8 @@
 S:	Maintained for 2.4; PCI support for 2.6.
 
 AMD GEODE PROCESSOR/CHIPSET SUPPORT
-P:      Jordan Crouse
-M:      info-linux@geode.amd.com
+P:	Jordan Crouse
+M:	info-linux@geode.amd.com
 L:	info-linux@geode.amd.com
 W:	http://www.amd.com/us-en/ConnectivitySolutions/TechnicalResources/0,,50_2334_2452_11363,00.html
 S:	Supported
@@ -601,13 +601,13 @@
 S:	Maintained
 
 BONDING DRIVER
-P:   Chad Tindel
-M:   ctindel@users.sourceforge.net
-P:   Jay Vosburgh
-M:   fubar@us.ibm.com
-L:   bonding-devel@lists.sourceforge.net
-W:   http://sourceforge.net/projects/bonding/
-S:   Supported
+P:	Chad Tindel
+M:	ctindel@users.sourceforge.net
+P:	Jay Vosburgh
+M:	fubar@us.ibm.com
+L:	bonding-devel@lists.sourceforge.net
+W:	http://sourceforge.net/projects/bonding/
+S:	Supported
 
 BROADBAND PROCESSOR ARCHITECTURE
 P:	Arnd Bergmann
@@ -744,8 +744,8 @@
 S:	Supported
 
 CRAMFS FILESYSTEM
-W:     http://sourceforge.net/projects/cramfs/
-S:     Orphan
+W:	http://sourceforge.net/projects/cramfs/
+S:	Orphan
 
 CRIS PORT
 P:	Mikael Starvik
@@ -1054,11 +1054,11 @@
 S:	Maintained
 
 EMULEX LPFC FC SCSI DRIVER
-P:      James Smart
-M:      james.smart@emulex.com
-L:      linux-scsi@vger.kernel.org
-W:      http://sourceforge.net/projects/lpfcxxxx
-S:      Supported
+P:	James Smart
+M:	james.smart@emulex.com
+L:	linux-scsi@vger.kernel.org
+W:	http://sourceforge.net/projects/lpfcxxxx
+S:	Supported
 
 EPSON 1355 FRAMEBUFFER DRIVER
 P:	Christopher Hoover
@@ -1495,16 +1495,16 @@
 S:	Maintained
 
 INTEL FRAMEBUFFER DRIVER (excluding 810 and 815)
-P:      Sylvain Meyer
-M:      sylvain.meyer@worldonline.fr
-L:      linux-fbdev-devel@lists.sourceforge.net
-S:      Maintained
+P:	Sylvain Meyer
+M:	sylvain.meyer@worldonline.fr
+L:	linux-fbdev-devel@lists.sourceforge.net
+S:	Maintained
 
 INTEL 810/815 FRAMEBUFFER DRIVER
-P:      Antonino Daplas
-M:      adaplas@pol.net
-L:      linux-fbdev-devel@lists.sourceforge.net
-S:      Maintained
+P:	Antonino Daplas
+M:	adaplas@pol.net
+L:	linux-fbdev-devel@lists.sourceforge.net
+S:	Maintained
 
 INTEL APIC/IOAPIC, LOWLEVEL X86 SMP SUPPORT
 P:	Ingo Molnar
@@ -1830,11 +1830,11 @@
 S:	Maintained
 
 LINUX FOR POWERPC EMBEDDED PPC83XX AND PPC85XX
-P:     Kumar Gala
-M:     galak@kernel.crashing.org
-W:     http://www.penguinppc.org/
-L:     linuxppc-embedded@ozlabs.org
-S:     Maintained
+P:	Kumar Gala
+M:	galak@kernel.crashing.org
+W:	http://www.penguinppc.org/
+L:	linuxppc-embedded@ozlabs.org
+S:	Maintained
 
 LINUX FOR POWERPC PA SEMI PWRFICIENT
 P:	Olof Johansson
@@ -1933,10 +1933,10 @@
 S: 	Supported
 
 MAN-PAGES: MANUAL PAGES FOR LINUX -- Sections 2, 3, 4, 5, and 7
-P: Michael Kerrisk
-M: mtk-manpages@gmx.net
-W: ftp://ftp.kernel.org/pub/linux/docs/manpages
-S: Maintained
+P:	Michael Kerrisk
+M:	mtk-manpages@gmx.net
+W:	ftp://ftp.kernel.org/pub/linux/docs/manpages
+S:	Maintained
 
 MARVELL MV643XX ETHERNET DRIVER
 P:	Dale Farnsworth
@@ -1953,11 +1953,11 @@
 S:	Maintained
 
 MEGARAID SCSI DRIVERS
-P:     Neela Syam Kolli
-M:     Neela.Kolli@engenio.com
-S:     linux-scsi@vger.kernel.org
-W:     http://megaraid.lsilogic.com
-S:     Maintained
+P:	Neela Syam Kolli
+M:	Neela.Kolli@engenio.com
+S:	linux-scsi@vger.kernel.org
+W:	http://megaraid.lsilogic.com
+S:	Maintained
 
 MEMORY MANAGEMENT
 L:	linux-mm@kvack.org
@@ -2186,10 +2186,10 @@
 S:	Maintained
 
 NVIDIA (rivafb and nvidiafb) FRAMEBUFFER DRIVER
-P:      Antonino Daplas
-M:      adaplas@pol.net
-L:      linux-fbdev-devel@lists.sourceforge.net
-S:      Maintained
+P:	Antonino Daplas
+M:	adaplas@pol.net
+L:	linux-fbdev-devel@lists.sourceforge.net
+S:	Maintained
 
 OPENCORES I2C BUS DRIVER
 P:	Peter Korsgaard
@@ -2539,10 +2539,10 @@
 S:	Orphan
 
 S3 SAVAGE FRAMEBUFFER DRIVER
-P:      Antonino Daplas
-M:      adaplas@pol.net
-L:      linux-fbdev-devel@lists.sourceforge.net
-S:      Maintained
+P:	Antonino Daplas
+M:	adaplas@pol.net
+L:	linux-fbdev-devel@lists.sourceforge.net
+S:	Maintained
 
 S390
 P:	Martin Schwidefsky
@@ -2623,10 +2623,10 @@
 S:	Maintained
 
 SCTP PROTOCOL
-P: Sridhar Samudrala
-M: sri@us.ibm.com
-L: lksctp-developers@lists.sourceforge.net
-S: Supported
+P:	Sridhar Samudrala
+M:	sri@us.ibm.com
+L:	lksctp-developers@lists.sourceforge.net
+S:	Supported
 
 SCx200 CPU SUPPORT
 P:	Jim Cromie
@@ -2794,9 +2794,9 @@
 S:	Maintained
 
 Telecom Clock Driver for MCPL0010
-P: Mark Gross
-M: mark.gross@intel.com
-S: Supported
+P:	Mark Gross
+M:	mark.gross@intel.com
+S:	Supported
 
 TENSILICA XTENSA PORT (xtensa):
 P:	Chris Zankel
@@ -2943,9 +2943,9 @@
 S:	Maintained
 
 TI PARALLEL LINK CABLE DRIVER
-P:     Romain Lievin
-M:     roms@lpg.ticalc.org
-S:     Maintained
+P:	Romain Lievin
+M:	roms@lpg.ticalc.org
+S:	Maintained
 
 TIPC NETWORK LAYER
 P:	Per Liden
@@ -2995,12 +2995,12 @@
 S:	Maintained
 
 TRIVIAL PATCHES
-P:      Adrian Bunk
-M:      trivial@kernel.org
-L:      linux-kernel@vger.kernel.org
-W:      http://www.kernel.org/pub/linux/kernel/people/bunk/trivial/
-T:      git kernel.org:/pub/scm/linux/kernel/git/bunk/trivial.git
-S:      Maintained
+P:	Adrian Bunk
+M:	trivial@kernel.org
+L:	linux-kernel@vger.kernel.org
+W:	http://www.kernel.org/pub/linux/kernel/people/bunk/trivial/
+T:	git kernel.org:/pub/scm/linux/kernel/git/bunk/trivial.git
+S:	Maintained
 
 TMS380 TOKEN-RING NETWORK DRIVER
 P:	Adam Fritzler
diff --git a/arch/arm/mach-ixp4xx/Kconfig b/arch/arm/mach-ixp4xx/Kconfig
index 57f23b4..e316bd9 100644
--- a/arch/arm/mach-ixp4xx/Kconfig
+++ b/arch/arm/mach-ixp4xx/Kconfig
@@ -133,7 +133,7 @@
              into the kernel and we can use the standard read[bwl]/write[bwl]
              macros. This is the preferred method due to speed but it
              limits the system to just 64MB of PCI memory. This can be 
-             problamatic if using video cards and other memory-heavy devices.
+             problematic if using video cards and other memory-heavy devices.
           
           2) If > 64MB of memory space is required, the IXP4xx can be 
 	     configured to use indirect registers to access PCI This allows 
diff --git a/arch/arm/mach-lh7a40x/Kconfig b/arch/arm/mach-lh7a40x/Kconfig
index 147b019..6f4c6a1 100644
--- a/arch/arm/mach-lh7a40x/Kconfig
+++ b/arch/arm/mach-lh7a40x/Kconfig
@@ -8,7 +8,7 @@
 	help
 	  Say Y here if you are using the Sharp KEV7A400 development
 	  board.  This hardware is discontinued, so I'd be very
-	  suprised if you wanted this option.
+	  surprised if you wanted this option.
 
 config MACH_LPD7A400
 	bool "LPD7A400 Card Engine"
diff --git a/arch/arm/mach-s3c2410/Kconfig b/arch/arm/mach-s3c2410/Kconfig
index 63965c7..9aa26b9 100644
--- a/arch/arm/mach-s3c2410/Kconfig
+++ b/arch/arm/mach-s3c2410/Kconfig
@@ -91,7 +91,7 @@
 config MACH_S3C2413
 	bool
 	help
-	  Internal node for S3C2413 verison of SMDK2413, so that
+	  Internal node for S3C2413 version of SMDK2413, so that
 	  machine_is_s3c2413() will work when MACH_SMDK2413 is
 	  selected
 
diff --git a/arch/arm/mm/Kconfig b/arch/arm/mm/Kconfig
index c0bfb82..b09a19f 100644
--- a/arch/arm/mm/Kconfig
+++ b/arch/arm/mm/Kconfig
@@ -197,7 +197,7 @@
 	select CPU_CP15_MPU
 	help
 	  ARM940T is a member of the ARM9TDMI family of general-
-	  purpose microprocessors with MPU and seperate 4KB
+	  purpose microprocessors with MPU and separate 4KB
 	  instruction and 4KB data cases, each with a 4-word line
 	  length.
 
diff --git a/arch/cris/arch-v10/Kconfig b/arch/cris/arch-v10/Kconfig
index 44eb1b9..c7ea9ef 100644
--- a/arch/cris/arch-v10/Kconfig
+++ b/arch/cris/arch-v10/Kconfig
@@ -323,7 +323,7 @@
 	depends on ETRAX_ARCH_V10
 	default "95a6"
 	help
-	  Waitstates for SRAM, Flash and peripherials (not DRAM).  95f8 is a
+	  Waitstates for SRAM, Flash and peripherals (not DRAM).  95f8 is a
 	  good choice for most Axis products...
 
 config ETRAX_DEF_R_BUS_CONFIG
diff --git a/arch/cris/arch-v10/drivers/Kconfig b/arch/cris/arch-v10/drivers/Kconfig
index 734d5f3..e7e724bc 100644
--- a/arch/cris/arch-v10/drivers/Kconfig
+++ b/arch/cris/arch-v10/drivers/Kconfig
@@ -839,7 +839,7 @@
 	default "0"
 	help
 	  This controls the initial value of the trickle charge register.
-	  0 = disabled (use this if you are unsure or have a non rechargable battery)
+	  0 = disabled (use this if you are unsure or have a non rechargeable battery)
 	  Otherwise the following values can be OR:ed together to control the
 	  charge current:
 	  1 = 2kohm, 2 = 4kohm, 3 = 4kohm
diff --git a/arch/cris/arch-v10/drivers/eeprom.c b/arch/cris/arch-v10/drivers/eeprom.c
index 6e1f191..284ebfd 100644
--- a/arch/cris/arch-v10/drivers/eeprom.c
+++ b/arch/cris/arch-v10/drivers/eeprom.c
@@ -1,7 +1,7 @@
 /*!*****************************************************************************
 *!
-*!  Implements an interface for i2c compatible eeproms to run under linux.
-*!  Supports 2k, 8k(?) and 16k. Uses adaptive timing adjustents by
+*!  Implements an interface for i2c compatible eeproms to run under Linux.
+*!  Supports 2k, 8k(?) and 16k. Uses adaptive timing adjustments by
 *!  Johan.Adolfsson@axis.com
 *!
 *!  Probing results:
@@ -51,7 +51,7 @@
 *!  Revision 1.8  2001/06/15 13:24:29  jonashg
 *!  * Added verification of pointers from userspace in read and write.
 *!  * Made busy counter volatile.
-*!  * Added define for inital write delay.
+*!  * Added define for initial write delay.
 *!  * Removed warnings by using loff_t instead of unsigned long.
 *!
 *!  Revision 1.7  2001/06/14 15:26:54  jonashg
diff --git a/arch/cris/arch-v10/drivers/i2c.c b/arch/cris/arch-v10/drivers/i2c.c
index 6114596..092c724 100644
--- a/arch/cris/arch-v10/drivers/i2c.c
+++ b/arch/cris/arch-v10/drivers/i2c.c
@@ -47,7 +47,7 @@
 *! Update Port B register and shadow even when running with hardware support
 *!   to avoid glitches when reading bits
 *! Never set direction to out in i2c_inbyte
-*! Removed incorrect clock togling at end of i2c_inbyte
+*! Removed incorrect clock toggling at end of i2c_inbyte
 *!
 *! Revision 1.8  2002/08/13 06:31:53  starvik
 *! Made SDA and SCL line configurable
diff --git a/arch/cris/arch-v10/kernel/kgdb.c b/arch/cris/arch-v10/kernel/kgdb.c
index 34528da..07628a1 100644
--- a/arch/cris/arch-v10/kernel/kgdb.c
+++ b/arch/cris/arch-v10/kernel/kgdb.c
@@ -33,7 +33,7 @@
 *!
 *! Revision 1.2  2002/11/19 14:35:24  starvik
 *! Changes from linux 2.4
-*! Changed struct initializer syntax to the currently prefered notation
+*! Changed struct initializer syntax to the currently preferred notation
 *!
 *! Revision 1.1  2001/12/17 13:59:27  bjornw
 *! Initial revision
diff --git a/arch/cris/arch-v32/drivers/Kconfig b/arch/cris/arch-v32/drivers/Kconfig
index a33097f..f64624f 100644
--- a/arch/cris/arch-v32/drivers/Kconfig
+++ b/arch/cris/arch-v32/drivers/Kconfig
@@ -88,7 +88,7 @@
 	help
 	  Enables the DMA7 input channel for ser0 (ttyS0).
 	  If you do not enable DMA, an interrupt for each character will be
-	  used when receiveing data.
+	  used when receiving data.
 	  Normally you want to use DMA, unless you use the DMA channel for
 	  something else.
 
@@ -157,7 +157,7 @@
 	help
 	  Enables the DMA5 input channel for ser1 (ttyS1).
 	  If you do not enable DMA, an interrupt for each character will be
-	  used when receiveing data.
+	  used when receiving data.
 	  Normally you want this on, unless you use the DMA channel for
 	  something else.
 
@@ -228,7 +228,7 @@
 	help
 	  Enables the DMA3 input channel for ser2 (ttyS2).
 	  If you do not enable DMA, an interrupt for each character will be
-	  used when receiveing data.
+	  used when receiving data.
 	  Normally you want to use DMA, unless you use the DMA channel for
 	  something else.
 
@@ -297,7 +297,7 @@
 	help
 	  Enables the DMA9 input channel for ser3 (ttyS3).
 	  If you do not enable DMA, an interrupt for each character will be
-	  used when receiveing data.
+	  used when receiving data.
 	  Normally you want to use DMA, unless you use the DMA channel for
 	  something else.
 
diff --git a/arch/i386/kernel/cpuid.c b/arch/i386/kernel/cpuid.c
index fde8bea..ab0c327 100644
--- a/arch/i386/kernel/cpuid.c
+++ b/arch/i386/kernel/cpuid.c
@@ -156,14 +156,14 @@
 	.open = cpuid_open,
 };
 
-static int cpuid_class_device_create(int i)
+static int cpuid_device_create(int i)
 {
 	int err = 0;
-	struct class_device *class_err;
+	struct device *dev;
 
-	class_err = class_device_create(cpuid_class, NULL, MKDEV(CPUID_MAJOR, i), NULL, "cpu%d",i);
-	if (IS_ERR(class_err))
-		err = PTR_ERR(class_err);
+	dev = device_create(cpuid_class, NULL, MKDEV(CPUID_MAJOR, i), "cpu%d",i);
+	if (IS_ERR(dev))
+		err = PTR_ERR(dev);
 	return err;
 }
 
@@ -174,10 +174,10 @@
 
 	switch (action) {
 	case CPU_ONLINE:
-		cpuid_class_device_create(cpu);
+		cpuid_device_create(cpu);
 		break;
 	case CPU_DEAD:
-		class_device_destroy(cpuid_class, MKDEV(CPUID_MAJOR, cpu));
+		device_destroy(cpuid_class, MKDEV(CPUID_MAJOR, cpu));
 		break;
 	}
 	return NOTIFY_OK;
@@ -206,7 +206,7 @@
 		goto out_chrdev;
 	}
 	for_each_online_cpu(i) {
-		err = cpuid_class_device_create(i);
+		err = cpuid_device_create(i);
 		if (err != 0) 
 			goto out_class;
 	}
@@ -218,7 +218,7 @@
 out_class:
 	i = 0;
 	for_each_online_cpu(i) {
-		class_device_destroy(cpuid_class, MKDEV(CPUID_MAJOR, i));
+		device_destroy(cpuid_class, MKDEV(CPUID_MAJOR, i));
 	}
 	class_destroy(cpuid_class);
 out_chrdev:
@@ -232,7 +232,7 @@
 	int cpu = 0;
 
 	for_each_online_cpu(cpu)
-		class_device_destroy(cpuid_class, MKDEV(CPUID_MAJOR, cpu));
+		device_destroy(cpuid_class, MKDEV(CPUID_MAJOR, cpu));
 	class_destroy(cpuid_class);
 	unregister_chrdev(CPUID_MAJOR, "cpu/cpuid");
 	unregister_hotcpu_notifier(&cpuid_class_cpu_notifier);
diff --git a/arch/i386/kernel/msr.c b/arch/i386/kernel/msr.c
index d535cdb..a773f77 100644
--- a/arch/i386/kernel/msr.c
+++ b/arch/i386/kernel/msr.c
@@ -239,14 +239,14 @@
 	.open = msr_open,
 };
 
-static int msr_class_device_create(int i)
+static int msr_device_create(int i)
 {
 	int err = 0;
-	struct class_device *class_err;
+	struct device *dev;
 
-	class_err = class_device_create(msr_class, NULL, MKDEV(MSR_MAJOR, i), NULL, "msr%d",i);
-	if (IS_ERR(class_err)) 
-		err = PTR_ERR(class_err);
+	dev = device_create(msr_class, NULL, MKDEV(MSR_MAJOR, i), "msr%d",i);
+	if (IS_ERR(dev))
+		err = PTR_ERR(dev);
 	return err;
 }
 
@@ -258,10 +258,10 @@
 
 	switch (action) {
 	case CPU_ONLINE:
-		msr_class_device_create(cpu);
+		msr_device_create(cpu);
 		break;
 	case CPU_DEAD:
-		class_device_destroy(msr_class, MKDEV(MSR_MAJOR, cpu));
+		device_destroy(msr_class, MKDEV(MSR_MAJOR, cpu));
 		break;
 	}
 	return NOTIFY_OK;
@@ -290,7 +290,7 @@
 		goto out_chrdev;
 	}
 	for_each_online_cpu(i) {
-		err = msr_class_device_create(i);
+		err = msr_device_create(i);
 		if (err != 0)
 			goto out_class;
 	}
@@ -302,7 +302,7 @@
 out_class:
 	i = 0;
 	for_each_online_cpu(i)
-		class_device_destroy(msr_class, MKDEV(MSR_MAJOR, i));
+		device_destroy(msr_class, MKDEV(MSR_MAJOR, i));
 	class_destroy(msr_class);
 out_chrdev:
 	unregister_chrdev(MSR_MAJOR, "cpu/msr");
@@ -314,7 +314,7 @@
 {
 	int cpu = 0;
 	for_each_online_cpu(cpu)
-		class_device_destroy(msr_class, MKDEV(MSR_MAJOR, cpu));
+		device_destroy(msr_class, MKDEV(MSR_MAJOR, cpu));
 	class_destroy(msr_class);
 	unregister_chrdev(MSR_MAJOR, "cpu/msr");
 	unregister_hotcpu_notifier(&msr_class_cpu_notifier);
diff --git a/arch/i386/kernel/pci-dma.c b/arch/i386/kernel/pci-dma.c
index 25fe668..5c8c6ef 100644
--- a/arch/i386/kernel/pci-dma.c
+++ b/arch/i386/kernel/pci-dma.c
@@ -75,7 +75,7 @@
 int dma_declare_coherent_memory(struct device *dev, dma_addr_t bus_addr,
 				dma_addr_t device_addr, size_t size, int flags)
 {
-	void __iomem *mem_base;
+	void __iomem *mem_base = NULL;
 	int pages = size >> PAGE_SHIFT;
 	int bitmap_size = (pages + 31)/32;
 
@@ -114,6 +114,8 @@
  free1_out:
 	kfree(dev->dma_mem->bitmap);
  out:
+	if (mem_base)
+		iounmap(mem_base);
 	return 0;
 }
 EXPORT_SYMBOL(dma_declare_coherent_memory);
diff --git a/arch/i386/pci/common.c b/arch/i386/pci/common.c
index cdfcf97..53ca6e8 100644
--- a/arch/i386/pci/common.c
+++ b/arch/i386/pci/common.c
@@ -20,7 +20,7 @@
 unsigned int pci_probe = PCI_PROBE_BIOS | PCI_PROBE_CONF1 | PCI_PROBE_CONF2 |
 				PCI_PROBE_MMCONF;
 
-int pci_bf_sort;
+static int pci_bf_sort;
 int pci_routeirq;
 int pcibios_last_bus = -1;
 unsigned long pirq_table_addr;
diff --git a/arch/i386/pci/fixup.c b/arch/i386/pci/fixup.c
index c1949ff..cde1170 100644
--- a/arch/i386/pci/fixup.c
+++ b/arch/i386/pci/fixup.c
@@ -74,52 +74,6 @@
 }
 DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_NCR, PCI_DEVICE_ID_NCR_53C810, pci_fixup_ncr53c810);
 
-static void __devinit pci_fixup_ide_bases(struct pci_dev *d)
-{
-	int i;
-
-	/*
-	 * PCI IDE controllers use non-standard I/O port decoding, respect it.
-	 */
-	if ((d->class >> 8) != PCI_CLASS_STORAGE_IDE)
-		return;
-	DBG("PCI: IDE base address fixup for %s\n", pci_name(d));
-	for(i=0; i<4; i++) {
-		struct resource *r = &d->resource[i];
-		if ((r->start & ~0x80) == 0x374) {
-			r->start |= 2;
-			r->end = r->start;
-		}
-	}
-}
-DECLARE_PCI_FIXUP_HEADER(PCI_ANY_ID, PCI_ANY_ID, pci_fixup_ide_bases);
-
-static void __devinit  pci_fixup_ide_trash(struct pci_dev *d)
-{
-	int i;
-
-	/*
-	 * Runs the fixup only for the first IDE controller
-	 * (Shai Fultheim - shai@ftcon.com)
-	 */
-	static int called = 0;
-	if (called)
-		return;
-	called = 1;
-
-	/*
-	 * There exist PCI IDE controllers which have utter garbage
-	 * in first four base registers. Ignore that.
-	 */
-	DBG("PCI: IDE base address trash cleared for %s\n", pci_name(d));
-	for(i=0; i<4; i++)
-		d->resource[i].start = d->resource[i].end = d->resource[i].flags = 0;
-}
-DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_SI, PCI_DEVICE_ID_SI_5513, pci_fixup_ide_trash);
-DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82801CA_10, pci_fixup_ide_trash);
-DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82801CA_11, pci_fixup_ide_trash);
-DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82801DB_9, pci_fixup_ide_trash);
-
 static void __devinit  pci_fixup_latency(struct pci_dev *d)
 {
 	/*
diff --git a/arch/i386/pci/i386.c b/arch/i386/pci/i386.c
index 9858029..43005f0 100644
--- a/arch/i386/pci/i386.c
+++ b/arch/i386/pci/i386.c
@@ -104,16 +104,24 @@
 	/* Depth-First Search on bus tree */
 	list_for_each_entry(bus, bus_list, node) {
 		if ((dev = bus->self)) {
-			for (idx = PCI_BRIDGE_RESOURCES; idx < PCI_NUM_RESOURCES; idx++) {
+			for (idx = PCI_BRIDGE_RESOURCES;
+			    idx < PCI_NUM_RESOURCES; idx++) {
 				r = &dev->resource[idx];
 				if (!r->flags)
 					continue;
 				pr = pci_find_parent_resource(dev, r);
-				if (!r->start || !pr || request_resource(pr, r) < 0) {
-					printk(KERN_ERR "PCI: Cannot allocate resource region %d of bridge %s\n", idx, pci_name(dev));
-					/* Something is wrong with the region.
-					   Invalidate the resource to prevent child
-					   resource allocations in this range. */
+				if (!r->start || !pr ||
+				    request_resource(pr, r) < 0) {
+					printk(KERN_ERR "PCI: Cannot allocate "
+						"resource region %d "
+						"of bridge %s\n",
+						idx, pci_name(dev));
+					/*
+					 * Something is wrong with the region.
+					 * Invalidate the resource to prevent
+					 * child resource allocations in this
+					 * range.
+					 */
 					r->flags = 0;
 				}
 			}
@@ -131,7 +139,7 @@
 
 	for_each_pci_dev(dev) {
 		pci_read_config_word(dev, PCI_COMMAND, &command);
-		for(idx = 0; idx < 6; idx++) {
+		for (idx = 0; idx < PCI_ROM_RESOURCE; idx++) {
 			r = &dev->resource[idx];
 			if (r->parent)		/* Already allocated */
 				continue;
@@ -142,11 +150,15 @@
 			else
 				disabled = !(command & PCI_COMMAND_MEMORY);
 			if (pass == disabled) {
-				DBG("PCI: Resource %08lx-%08lx (f=%lx, d=%d, p=%d)\n",
+				DBG("PCI: Resource %08lx-%08lx "
+				    "(f=%lx, d=%d, p=%d)\n",
 				    r->start, r->end, r->flags, disabled, pass);
 				pr = pci_find_parent_resource(dev, r);
 				if (!pr || request_resource(pr, r) < 0) {
-					printk(KERN_ERR "PCI: Cannot allocate resource region %d of device %s\n", idx, pci_name(dev));
+					printk(KERN_ERR "PCI: Cannot allocate "
+						"resource region %d "
+						"of device %s\n",
+						idx, pci_name(dev));
 					/* We'll assign a new address later */
 					r->end -= r->start;
 					r->start = 0;
@@ -156,12 +168,16 @@
 		if (!pass) {
 			r = &dev->resource[PCI_ROM_RESOURCE];
 			if (r->flags & IORESOURCE_ROM_ENABLE) {
-				/* Turn the ROM off, leave the resource region, but keep it unregistered. */
+				/* Turn the ROM off, leave the resource region,
+				 * but keep it unregistered. */
 				u32 reg;
-				DBG("PCI: Switching off ROM of %s\n", pci_name(dev));
+				DBG("PCI: Switching off ROM of %s\n",
+					pci_name(dev));
 				r->flags &= ~IORESOURCE_ROM_ENABLE;
-				pci_read_config_dword(dev, dev->rom_base_reg, &reg);
-				pci_write_config_dword(dev, dev->rom_base_reg, reg & ~PCI_ROM_ADDRESS_ENABLE);
+				pci_read_config_dword(dev,
+						dev->rom_base_reg, &reg);
+				pci_write_config_dword(dev, dev->rom_base_reg,
+						reg & ~PCI_ROM_ADDRESS_ENABLE);
 			}
 		}
 	}
@@ -173,9 +189,11 @@
 	struct resource *r, *pr;
 
 	if (!(pci_probe & PCI_ASSIGN_ROMS)) {
-		/* Try to use BIOS settings for ROMs, otherwise let
-		   pci_assign_unassigned_resources() allocate the new
-		   addresses. */
+		/*
+		 * Try to use BIOS settings for ROMs, otherwise let
+		 * pci_assign_unassigned_resources() allocate the new
+		 * addresses.
+		 */
 		for_each_pci_dev(dev) {
 			r = &dev->resource[PCI_ROM_RESOURCE];
 			if (!r->flags || !r->start)
@@ -215,9 +233,9 @@
 
 	pci_read_config_word(dev, PCI_COMMAND, &cmd);
 	old_cmd = cmd;
-	for(idx = 0; idx < PCI_NUM_RESOURCES; idx++) {
+	for (idx = 0; idx < PCI_NUM_RESOURCES; idx++) {
 		/* Only set up the requested stuff */
-		if (!(mask & (1<<idx)))
+		if (!(mask & (1 << idx)))
 			continue;
 
 		r = &dev->resource[idx];
@@ -227,7 +245,9 @@
 				(!(r->flags & IORESOURCE_ROM_ENABLE)))
 			continue;
 		if (!r->start && r->end) {
-			printk(KERN_ERR "PCI: Device %s not available because of resource collisions\n", pci_name(dev));
+			printk(KERN_ERR "PCI: Device %s not available "
+				"because of resource collisions\n",
+				pci_name(dev));
 			return -EINVAL;
 		}
 		if (r->flags & IORESOURCE_IO)
@@ -236,7 +256,8 @@
 			cmd |= PCI_COMMAND_MEMORY;
 	}
 	if (cmd != old_cmd) {
-		printk("PCI: Enabling device %s (%04x -> %04x)\n", pci_name(dev), old_cmd, cmd);
+		printk("PCI: Enabling device %s (%04x -> %04x)\n",
+			pci_name(dev), old_cmd, cmd);
 		pci_write_config_word(dev, PCI_COMMAND, cmd);
 	}
 	return 0;
@@ -258,7 +279,8 @@
 		lat = pcibios_max_latency;
 	else
 		return;
-	printk(KERN_DEBUG "PCI: Setting latency timer of device %s to %d\n", pci_name(dev), lat);
+	printk(KERN_DEBUG "PCI: Setting latency timer of device %s to %d\n",
+		pci_name(dev), lat);
 	pci_write_config_byte(dev, PCI_LATENCY_TIMER, lat);
 }
 
diff --git a/arch/i386/pci/irq.c b/arch/i386/pci/irq.c
index 6916399..e65551c 100644
--- a/arch/i386/pci/irq.c
+++ b/arch/i386/pci/irq.c
@@ -543,6 +543,12 @@
 		case PCI_DEVICE_ID_INTEL_ICH8_2:
 		case PCI_DEVICE_ID_INTEL_ICH8_3:
 		case PCI_DEVICE_ID_INTEL_ICH8_4:
+		case PCI_DEVICE_ID_INTEL_ICH9_0:
+		case PCI_DEVICE_ID_INTEL_ICH9_1:
+		case PCI_DEVICE_ID_INTEL_ICH9_2:
+		case PCI_DEVICE_ID_INTEL_ICH9_3:
+		case PCI_DEVICE_ID_INTEL_ICH9_4:
+		case PCI_DEVICE_ID_INTEL_ICH9_5:
 			r->name = "PIIX/ICH";
 			r->get = pirq_piix_get;
 			r->set = pirq_piix_set;
diff --git a/arch/ia64/hp/common/sba_iommu.c b/arch/ia64/hp/common/sba_iommu.c
index db8e1fc..14691cd 100644
--- a/arch/ia64/hp/common/sba_iommu.c
+++ b/arch/ia64/hp/common/sba_iommu.c
@@ -75,7 +75,7 @@
 ** If a device prefetches beyond the end of a valid pdir entry, it will cause
 ** a hard failure, ie. MCA.  Version 3.0 and later of the zx1 LBA should
 ** disconnect on 4k boundaries and prevent such issues.  If the device is
-** particularly agressive, this option will keep the entire pdir valid such
+** particularly aggressive, this option will keep the entire pdir valid such
 ** that prefetching will hit a valid address.  This could severely impact
 ** error containment, and is therefore off by default.  The page that is
 ** used for spill-over is poisoned, so that should help debugging somewhat.
@@ -258,10 +258,10 @@
 
 /*
 ** DMA_CHUNK_SIZE is used by the SCSI mid-layer to break up
-** (or rather not merge) DMA's into managable chunks.
+** (or rather not merge) DMAs into manageable chunks.
 ** On parisc, this is more of the software/tuning constraint
-** rather than the HW. I/O MMU allocation alogorithms can be
-** faster with smaller size is (to some degree).
+** rather than the HW. I/O MMU allocation algorithms can be
+** faster with smaller sizes (to some degree).
 */
 #define DMA_CHUNK_SIZE  (BITS_PER_LONG*iovp_size)
 
diff --git a/arch/ia64/pci/pci.c b/arch/ia64/pci/pci.c
index b30be7c..f4edfbf 100644
--- a/arch/ia64/pci/pci.c
+++ b/arch/ia64/pci/pci.c
@@ -469,10 +469,11 @@
 	}
 }
 
-static void __devinit pcibios_fixup_device_resources(struct pci_dev *dev)
+void __devinit pcibios_fixup_device_resources(struct pci_dev *dev)
 {
 	pcibios_fixup_resources(dev, 0, PCI_BRIDGE_RESOURCES);
 }
+EXPORT_SYMBOL_GPL(pcibios_fixup_device_resources);
 
 static void __devinit pcibios_fixup_bridge_resources(struct pci_dev *dev)
 {
@@ -493,6 +494,7 @@
 	}
 	list_for_each_entry(dev, &b->devices, bus_list)
 		pcibios_fixup_device_resources(dev);
+	platform_pci_fixup_bus(b);
 
 	return;
 }
@@ -738,75 +740,44 @@
 	return ret;
 }
 
+/* It's defined in drivers/pci/pci.c */
+extern u8 pci_cache_line_size;
+
 /**
- * pci_cacheline_size - determine cacheline size for PCI devices
- * @dev: void
+ * set_pci_cacheline_size - determine cacheline size for PCI devices
  *
  * We want to use the line-size of the outer-most cache.  We assume
  * that this line-size is the same for all CPUs.
  *
  * Code mostly taken from arch/ia64/kernel/palinfo.c:cache_info().
- *
- * RETURNS: An appropriate -ERRNO error value on eror, or zero for success.
  */
-static unsigned long
-pci_cacheline_size (void)
+static void __init set_pci_cacheline_size(void)
 {
 	u64 levels, unique_caches;
 	s64 status;
 	pal_cache_config_info_t cci;
-	static u8 cacheline_size;
-
-	if (cacheline_size)
-		return cacheline_size;
 
 	status = ia64_pal_cache_summary(&levels, &unique_caches);
 	if (status != 0) {
-		printk(KERN_ERR "%s: ia64_pal_cache_summary() failed (status=%ld)\n",
-		       __FUNCTION__, status);
-		return SMP_CACHE_BYTES;
+		printk(KERN_ERR "%s: ia64_pal_cache_summary() failed "
+			"(status=%ld)\n", __FUNCTION__, status);
+		return;
 	}
 
-	status = ia64_pal_cache_config_info(levels - 1, /* cache_type (data_or_unified)= */ 2,
-					    &cci);
+	status = ia64_pal_cache_config_info(levels - 1,
+				/* cache_type (data_or_unified)= */ 2, &cci);
 	if (status != 0) {
-		printk(KERN_ERR "%s: ia64_pal_cache_config_info() failed (status=%ld)\n",
-		       __FUNCTION__, status);
-		return SMP_CACHE_BYTES;
+		printk(KERN_ERR "%s: ia64_pal_cache_config_info() failed "
+			"(status=%ld)\n", __FUNCTION__, status);
+		return;
 	}
-	cacheline_size = 1 << cci.pcci_line_size;
-	return cacheline_size;
+	pci_cache_line_size = (1 << cci.pcci_line_size) / 4;
 }
 
-/**
- * pcibios_prep_mwi - helper function for drivers/pci/pci.c:pci_set_mwi()
- * @dev: the PCI device for which MWI is enabled
- *
- * For ia64, we can get the cacheline sizes from PAL.
- *
- * RETURNS: An appropriate -ERRNO error value on eror, or zero for success.
- */
-int
-pcibios_prep_mwi (struct pci_dev *dev)
+static int __init pcibios_init(void)
 {
-	unsigned long desired_linesize, current_linesize;
-	int rc = 0;
-	u8 pci_linesize;
-
-	desired_linesize = pci_cacheline_size();
-
-	pci_read_config_byte(dev, PCI_CACHE_LINE_SIZE, &pci_linesize);
-	current_linesize = 4 * pci_linesize;
-	if (desired_linesize != current_linesize) {
-		printk(KERN_WARNING "PCI: slot %s has incorrect PCI cache line size of %lu bytes,",
-		       pci_name(dev), current_linesize);
-		if (current_linesize > desired_linesize) {
-			printk(" expected %lu bytes instead\n", desired_linesize);
-			rc = -EINVAL;
-		} else {
-			printk(" correcting to %lu\n", desired_linesize);
-			pci_write_config_byte(dev, PCI_CACHE_LINE_SIZE, desired_linesize / 4);
-		}
-	}
-	return rc;
+	set_pci_cacheline_size();
+	return 0;
 }
+
+subsys_initcall(pcibios_init);
diff --git a/arch/ia64/sn/kernel/Makefile b/arch/ia64/sn/kernel/Makefile
index 2d78f34..0a59371 100644
--- a/arch/ia64/sn/kernel/Makefile
+++ b/arch/ia64/sn/kernel/Makefile
@@ -4,13 +4,14 @@
 # License.  See the file "COPYING" in the main directory of this archive
 # for more details.
 #
-# Copyright (C) 1999,2001-2005 Silicon Graphics, Inc.  All Rights Reserved.
+# Copyright (C) 1999,2001-2006 Silicon Graphics, Inc.  All Rights Reserved.
 #
 
 CPPFLAGS += -I$(srctree)/arch/ia64/sn/include
 
 obj-y				+= setup.o bte.o bte_error.o irq.o mca.o idle.o \
-				   huberror.o io_init.o iomv.o klconflib.o pio_phys.o \
+				   huberror.o io_acpi_init.o io_common.o \
+				   io_init.o iomv.o klconflib.o pio_phys.o \
 				   sn2/
 obj-$(CONFIG_IA64_GENERIC)      += machvec.o
 obj-$(CONFIG_SGI_TIOCX)		+= tiocx.o
diff --git a/arch/ia64/sn/kernel/io_acpi_init.c b/arch/ia64/sn/kernel/io_acpi_init.c
new file mode 100644
index 0000000..99d7f27
--- /dev/null
+++ b/arch/ia64/sn/kernel/io_acpi_init.c
@@ -0,0 +1,231 @@
+/*
+ * This file is subject to the terms and conditions of the GNU General Public
+ * License.  See the file "COPYING" in the main directory of this archive
+ * for more details.
+ *
+ * Copyright (C) 2006 Silicon Graphics, Inc. All rights reserved.
+ */
+
+#include <asm/sn/types.h>
+#include <asm/sn/addrs.h>
+#include <asm/sn/pcidev.h>
+#include <asm/sn/pcibus_provider_defs.h>
+#include <asm/sn/sn_sal.h>
+#include "xtalk/hubdev.h"
+#include <linux/acpi.h>
+
+
+/*
+ * The code in this file will only be executed when running with
+ * a PROM that has ACPI IO support. (i.e., SN_ACPI_BASE_SUPPORT() == 1)
+ */
+
+
+/*
+ * This value must match the UUID the PROM uses
+ * (io/acpi/defblk.c) when building a vendor descriptor.
+ */
+struct acpi_vendor_uuid sn_uuid = {
+	.subtype = 0,
+	.data	= { 0x2c, 0xc6, 0xa6, 0xfe, 0x9c, 0x44, 0xda, 0x11,
+		    0xa2, 0x7c, 0x08, 0x00, 0x69, 0x13, 0xea, 0x51 },
+};
+
+/*
+ * Perform the early IO init in PROM.
+ */
+static s64
+sal_ioif_init(u64 *result)
+{
+	struct ia64_sal_retval isrv = {0,0,0,0};
+
+	SAL_CALL_NOLOCK(isrv,
+			SN_SAL_IOIF_INIT, 0, 0, 0, 0, 0, 0, 0);
+	*result = isrv.v0;
+	return isrv.status;
+}
+
+/*
+ * sn_hubdev_add - The 'add' function of the acpi_sn_hubdev_driver.
+ *		   Called for every "SGIHUB" or "SGITIO" device defined
+ *		   in the ACPI namespace.
+ */
+static int __init
+sn_hubdev_add(struct acpi_device *device)
+{
+	struct acpi_buffer buffer = { ACPI_ALLOCATE_BUFFER, NULL };
+	u64 addr;
+	struct hubdev_info *hubdev;
+	struct hubdev_info *hubdev_ptr;
+	int i;
+	u64 nasid;
+	struct acpi_resource *resource;
+	int ret = 0;
+	acpi_status status;
+	struct acpi_resource_vendor_typed *vendor;
+	extern void sn_common_hubdev_init(struct hubdev_info *);
+
+	status = acpi_get_vendor_resource(device->handle, METHOD_NAME__CRS,
+					  &sn_uuid, &buffer);
+	if (ACPI_FAILURE(status)) {
+		printk(KERN_ERR
+		       "sn_hubdev_add: acpi_get_vendor_resource() failed: %d\n",
+		        status);
+		return 1;
+	}
+
+	resource = buffer.pointer;
+	vendor = &resource->data.vendor_typed;
+	if ((vendor->byte_length - sizeof(struct acpi_vendor_uuid)) !=
+	    sizeof(struct hubdev_info *)) {
+		printk(KERN_ERR
+		       "sn_hubdev_add: Invalid vendor data length: %d\n",
+		        vendor->byte_length);
+		ret = 1;
+		goto exit;
+	}
+
+	memcpy(&addr, vendor->byte_data, sizeof(struct hubdev_info *));
+	hubdev_ptr = __va((struct hubdev_info *) addr);
+
+	nasid = hubdev_ptr->hdi_nasid;
+	i = nasid_to_cnodeid(nasid);
+	hubdev = (struct hubdev_info *)(NODEPDA(i)->pdinfo);
+	*hubdev = *hubdev_ptr;
+	sn_common_hubdev_init(hubdev);
+
+exit:
+	kfree(buffer.pointer);
+	return ret;
+}
+
+/*
+ * sn_get_bussoft_ptr() - The pcibus_bussoft pointer is found in
+ *			  the ACPI Vendor resource for this bus.
+ */
+static struct pcibus_bussoft *
+sn_get_bussoft_ptr(struct pci_bus *bus)
+{
+	u64 addr;
+	struct acpi_buffer buffer = { ACPI_ALLOCATE_BUFFER, NULL };
+	acpi_handle handle;
+	struct pcibus_bussoft *prom_bussoft_ptr;
+	struct acpi_resource *resource;
+	acpi_status status;
+	struct acpi_resource_vendor_typed *vendor;
+
+
+	handle = PCI_CONTROLLER(bus)->acpi_handle;
+	status = acpi_get_vendor_resource(handle, METHOD_NAME__CRS,
+					  &sn_uuid, &buffer);
+	if (ACPI_FAILURE(status)) {
+		printk(KERN_ERR "get_acpi_pcibus_ptr: "
+		       "get_acpi_bussoft_info() failed: %d\n",
+		       status);
+		return NULL;
+	}
+	resource = buffer.pointer;
+	vendor = &resource->data.vendor_typed;
+
+	if ((vendor->byte_length - sizeof(struct acpi_vendor_uuid)) !=
+	     sizeof(struct pcibus_bussoft *)) {
+		printk(KERN_ERR
+		       "get_acpi_bussoft_ptr: Invalid vendor data "
+		       "length %d\n", vendor->byte_length);
+		kfree(buffer.pointer);
+		return NULL;
+	}
+	memcpy(&addr, vendor->byte_data, sizeof(struct pcibus_bussoft *));
+	prom_bussoft_ptr = __va((struct pcibus_bussoft *) addr);
+	kfree(buffer.pointer);
+
+	return prom_bussoft_ptr;
+}
+
+/*
+ * sn_acpi_bus_fixup
+ */
+void
+sn_acpi_bus_fixup(struct pci_bus *bus)
+{
+	struct pci_dev *pci_dev = NULL;
+	struct pcibus_bussoft *prom_bussoft_ptr;
+	extern void sn_common_bus_fixup(struct pci_bus *,
+					struct pcibus_bussoft *);
+
+	if (!bus->parent) {	/* If root bus */
+		prom_bussoft_ptr = sn_get_bussoft_ptr(bus);
+		if (prom_bussoft_ptr == NULL) {
+			printk(KERN_ERR
+			       "sn_pci_fixup_bus: 0x%04x:0x%02x Unable to "
+			       "obtain prom_bussoft_ptr\n",
+			       pci_domain_nr(bus), bus->number);
+			return;
+		}
+		sn_common_bus_fixup(bus, prom_bussoft_ptr);
+	}
+	list_for_each_entry(pci_dev, &bus->devices, bus_list) {
+		sn_pci_fixup_slot(pci_dev);
+	}
+}
+
+/*
+ * sn_acpi_slot_fixup - Perform any SN specific slot fixup.
+ *			At present there does not appear to be
+ *			any generic way to handle a ROM image
+ *			that has been shadowed by the PROM, so
+ *			we pass a pointer to it	within the
+ *			pcidev_info structure.
+ */
+
+void
+sn_acpi_slot_fixup(struct pci_dev *dev, struct pcidev_info *pcidev_info)
+{
+	void __iomem *addr;
+	size_t size;
+
+	if (pcidev_info->pdi_pio_mapped_addr[PCI_ROM_RESOURCE]) {
+		/*
+		 * A valid ROM image exists and has been shadowed by the
+		 * PROM. Setup the pci_dev ROM resource to point to
+		 * the shadowed copy.
+		 */
+		size = dev->resource[PCI_ROM_RESOURCE].end -
+				dev->resource[PCI_ROM_RESOURCE].start;
+		addr =
+		     ioremap(pcidev_info->pdi_pio_mapped_addr[PCI_ROM_RESOURCE],
+			     size);
+		dev->resource[PCI_ROM_RESOURCE].start = (unsigned long) addr;
+		dev->resource[PCI_ROM_RESOURCE].end =
+						(unsigned long) addr + size;
+		dev->resource[PCI_ROM_RESOURCE].flags |= IORESOURCE_ROM_BIOS_COPY;
+	}
+}
+
+static struct acpi_driver acpi_sn_hubdev_driver = {
+	.name = "SGI HUBDEV Driver",
+	.ids = "SGIHUB,SGITIO",
+	.ops = {
+		.add = sn_hubdev_add,
+		},
+};
+
+
+/*
+ * sn_io_acpi_init - PROM has ACPI support for IO, defining at a minimum the
+ *		     nodes and root buses in the DSDT. As a result, bus scanning
+ *		     will be initiated by the Linux ACPI code.
+ */
+
+void __init
+sn_io_acpi_init(void)
+{
+	u64 result;
+	s64 status;
+
+	acpi_bus_register_driver(&acpi_sn_hubdev_driver);
+	status = sal_ioif_init(&result);
+	if (status || result)
+		panic("sal_ioif_init failed: [%lx] %s\n",
+		      status, ia64_sal_strerror(status));
+}
diff --git a/arch/ia64/sn/kernel/io_common.c b/arch/ia64/sn/kernel/io_common.c
new file mode 100644
index 0000000..d4dd8f4
--- /dev/null
+++ b/arch/ia64/sn/kernel/io_common.c
@@ -0,0 +1,613 @@
+/*
+ * This file is subject to the terms and conditions of the GNU General Public
+ * License.  See the file "COPYING" in the main directory of this archive
+ * for more details.
+ *
+ * Copyright (C) 2006 Silicon Graphics, Inc. All rights reserved.
+ */
+
+#include <linux/bootmem.h>
+#include <asm/sn/types.h>
+#include <asm/sn/addrs.h>
+#include <asm/sn/sn_feature_sets.h>
+#include <asm/sn/geo.h>
+#include <asm/sn/io.h>
+#include <asm/sn/l1.h>
+#include <asm/sn/module.h>
+#include <asm/sn/pcibr_provider.h>
+#include <asm/sn/pcibus_provider_defs.h>
+#include <asm/sn/pcidev.h>
+#include <asm/sn/simulator.h>
+#include <asm/sn/sn_sal.h>
+#include <asm/sn/tioca_provider.h>
+#include <asm/sn/tioce_provider.h>
+#include "xtalk/hubdev.h"
+#include "xtalk/xwidgetdev.h"
+#include <linux/acpi.h>
+#include <asm/sn/sn2/sn_hwperf.h>
+#include <asm/sn/acpi.h>
+
+extern void sn_init_cpei_timer(void);
+extern void register_sn_procfs(void);
+extern void sn_acpi_bus_fixup(struct pci_bus *);
+extern void sn_bus_fixup(struct pci_bus *);
+extern void sn_acpi_slot_fixup(struct pci_dev *, struct pcidev_info *);
+extern void sn_more_slot_fixup(struct pci_dev *, struct pcidev_info *);
+extern void sn_legacy_pci_window_fixup(struct pci_controller *, u64, u64);
+extern void sn_io_acpi_init(void);
+extern void sn_io_init(void);
+
+
+static struct list_head sn_sysdata_list;
+
+/* sysdata list struct */
+struct sysdata_el {
+	struct list_head entry;
+	void *sysdata;
+};
+
+int sn_ioif_inited;		/* SN I/O infrastructure initialized? */
+
+struct sn_pcibus_provider *sn_pci_provider[PCIIO_ASIC_MAX_TYPES];	/* indexed by asic type */
+
+/*
+ * Hooks and struct for unsupported pci providers
+ */
+
+static dma_addr_t
+sn_default_pci_map(struct pci_dev *pdev, unsigned long paddr, size_t size, int type)
+{
+	return 0;
+}
+
+static void
+sn_default_pci_unmap(struct pci_dev *pdev, dma_addr_t addr, int direction)
+{
+	return;
+}
+
+static void *
+sn_default_pci_bus_fixup(struct pcibus_bussoft *soft, struct pci_controller *controller)
+{
+	return NULL;
+}
+
+static struct sn_pcibus_provider sn_pci_default_provider = {
+	.dma_map = sn_default_pci_map,
+	.dma_map_consistent = sn_default_pci_map,
+	.dma_unmap = sn_default_pci_unmap,
+	.bus_fixup = sn_default_pci_bus_fixup,
+};
+
+/*
+ * Retrieve the DMA Flush List given nasid, widget, and device.
+ * This list is needed to implement the WAR - Flush DMA data on PIO Reads.
+ */
+static inline u64
+sal_get_device_dmaflush_list(u64 nasid, u64 widget_num, u64 device_num,
+			     u64 address)
+{
+	struct ia64_sal_retval ret_stuff;
+	ret_stuff.status = 0;
+	ret_stuff.v0 = 0;
+
+	SAL_CALL_NOLOCK(ret_stuff,
+			(u64) SN_SAL_IOIF_GET_DEVICE_DMAFLUSH_LIST,
+			(u64) nasid, (u64) widget_num,
+			(u64) device_num, (u64) address, 0, 0, 0);
+	return ret_stuff.status;
+}
+
+/*
+ * Retrieve the pci device information given the bus and device|function number.
+ */
+static inline u64
+sal_get_pcidev_info(u64 segment, u64 bus_number, u64 devfn, u64 pci_dev,
+		    u64 sn_irq_info)
+{
+	struct ia64_sal_retval ret_stuff;
+	ret_stuff.status = 0;
+	ret_stuff.v0 = 0;
+
+	SAL_CALL_NOLOCK(ret_stuff,
+			(u64) SN_SAL_IOIF_GET_PCIDEV_INFO,
+			(u64) segment, (u64) bus_number, (u64) devfn,
+			(u64) pci_dev,
+			sn_irq_info, 0, 0);
+	return ret_stuff.v0;
+}
+
+/*
+ * sn_pcidev_info_get() - Retrieve the pcidev_info struct for the specified
+ *			  device.
+ */
+inline struct pcidev_info *
+sn_pcidev_info_get(struct pci_dev *dev)
+{
+	struct pcidev_info *pcidev;
+
+	list_for_each_entry(pcidev,
+			    &(SN_PLATFORM_DATA(dev)->pcidev_info), pdi_list) {
+		if (pcidev->pdi_linux_pcidev == dev)
+			return pcidev;
+	}
+	return NULL;
+}
+
+/* Older PROM flush WAR
+ *
+ * 01/16/06 -- This war will be in place until a new official PROM is released.
+ * Additionally note that the struct sn_flush_device_war also has to be
+ * removed from arch/ia64/sn/include/xtalk/hubdev.h
+ */
+static u8 war_implemented = 0;
+
+static s64 sn_device_fixup_war(u64 nasid, u64 widget, int device,
+			       struct sn_flush_device_common *common)
+{
+	struct sn_flush_device_war *war_list;
+	struct sn_flush_device_war *dev_entry;
+	struct ia64_sal_retval isrv = {0,0,0,0};
+
+	if (!war_implemented) {
+		printk(KERN_WARNING "PROM version < 4.50 -- implementing old "
+		       "PROM flush WAR\n");
+		war_implemented = 1;
+	}
+
+	war_list = kzalloc(DEV_PER_WIDGET * sizeof(*war_list), GFP_KERNEL);
+	if (!war_list)
+		BUG();
+
+	SAL_CALL_NOLOCK(isrv, SN_SAL_IOIF_GET_WIDGET_DMAFLUSH_LIST,
+			nasid, widget, __pa(war_list), 0, 0, 0 ,0);
+	if (isrv.status)
+		panic("sn_device_fixup_war failed: %s\n",
+		      ia64_sal_strerror(isrv.status));
+
+	dev_entry = war_list + device;
+	memcpy(common,dev_entry, sizeof(*common));
+	kfree(war_list);
+
+	return isrv.status;
+}
+
+/*
+ * sn_common_hubdev_init() - This routine is called to initialize the HUB data
+ *			     structure for each node in the system.
+ */
+void __init
+sn_common_hubdev_init(struct hubdev_info *hubdev)
+{
+
+	struct sn_flush_device_kernel *sn_flush_device_kernel;
+	struct sn_flush_device_kernel *dev_entry;
+	s64 status;
+	int widget, device, size;
+
+	/* Attach the error interrupt handlers */
+	if (hubdev->hdi_nasid & 1)	/* If TIO */
+		ice_error_init(hubdev);
+	else
+		hub_error_init(hubdev);
+
+	for (widget = 0; widget <= HUB_WIDGET_ID_MAX; widget++)
+		hubdev->hdi_xwidget_info[widget].xwi_hubinfo = hubdev;
+
+	if (!hubdev->hdi_flush_nasid_list.widget_p)
+		return;
+
+	size = (HUB_WIDGET_ID_MAX + 1) *
+		sizeof(struct sn_flush_device_kernel *);
+	hubdev->hdi_flush_nasid_list.widget_p =
+		kzalloc(size, GFP_KERNEL);
+	if (!hubdev->hdi_flush_nasid_list.widget_p)
+		BUG();
+
+	for (widget = 0; widget <= HUB_WIDGET_ID_MAX; widget++) {
+		size = DEV_PER_WIDGET *
+			sizeof(struct sn_flush_device_kernel);
+		sn_flush_device_kernel = kzalloc(size, GFP_KERNEL);
+		if (!sn_flush_device_kernel)
+			BUG();
+
+		dev_entry = sn_flush_device_kernel;
+		for (device = 0; device < DEV_PER_WIDGET;
+		     device++, dev_entry++) {
+			size = sizeof(struct sn_flush_device_common);
+			dev_entry->common = kzalloc(size, GFP_KERNEL);
+			if (!dev_entry->common)
+				BUG();
+			if (sn_prom_feature_available(PRF_DEVICE_FLUSH_LIST))
+				status = sal_get_device_dmaflush_list(
+					     hubdev->hdi_nasid, widget, device,
+					     (u64)(dev_entry->common));
+			else
+				status = sn_device_fixup_war(hubdev->hdi_nasid,
+							     widget, device,
+							     dev_entry->common);
+			if (status != SALRET_OK)
+				panic("SAL call failed: %s\n",
+				      ia64_sal_strerror(status));
+
+			spin_lock_init(&dev_entry->sfdl_flush_lock);
+		}
+
+		if (sn_flush_device_kernel)
+			hubdev->hdi_flush_nasid_list.widget_p[widget] =
+							 sn_flush_device_kernel;
+	}
+}
+
+void sn_pci_unfixup_slot(struct pci_dev *dev)
+{
+	struct pci_dev *host_pci_dev = SN_PCIDEV_INFO(dev)->host_pci_dev;
+
+	sn_irq_unfixup(dev);
+	pci_dev_put(host_pci_dev);
+	pci_dev_put(dev);
+}
+
+/*
+ * sn_pci_fixup_slot() - This routine sets up a slot's resources consistent
+ *			 with the Linux PCI abstraction layer. Resources
+ *			 acquired from our PCI provider include PIO maps
+ *			 to BAR space and interrupt objects.
+ */
+void sn_pci_fixup_slot(struct pci_dev *dev)
+{
+	int segment = pci_domain_nr(dev->bus);
+	int status = 0;
+	struct pcibus_bussoft *bs;
+ 	struct pci_bus *host_pci_bus;
+ 	struct pci_dev *host_pci_dev;
+	struct pcidev_info *pcidev_info;
+ 	struct sn_irq_info *sn_irq_info;
+ 	unsigned int bus_no, devfn;
+
+	pci_dev_get(dev); /* for the sysdata pointer */
+	pcidev_info = kzalloc(sizeof(struct pcidev_info), GFP_KERNEL);
+	if (!pcidev_info)
+		BUG();		/* Cannot afford to run out of memory */
+
+	sn_irq_info = kzalloc(sizeof(struct sn_irq_info), GFP_KERNEL);
+	if (!sn_irq_info)
+		BUG();		/* Cannot afford to run out of memory */
+
+	/* Call to retrieve pci device information needed by kernel. */
+	status = sal_get_pcidev_info((u64) segment, (u64) dev->bus->number,
+				     dev->devfn,
+				     (u64) __pa(pcidev_info),
+				     (u64) __pa(sn_irq_info));
+	if (status)
+		BUG(); /* Cannot get platform pci device information */
+
+	/* Add pcidev_info to list in pci_controller.platform_data */
+	list_add_tail(&pcidev_info->pdi_list,
+		      &(SN_PLATFORM_DATA(dev->bus)->pcidev_info));
+
+	if (SN_ACPI_BASE_SUPPORT())
+		sn_acpi_slot_fixup(dev, pcidev_info);
+	else
+		sn_more_slot_fixup(dev, pcidev_info);
+	/*
+	 * Using the PROMs values for the PCI host bus, get the Linux
+ 	 * PCI host_pci_dev struct and set up host bus linkages
+ 	 */
+
+	bus_no = (pcidev_info->pdi_slot_host_handle >> 32) & 0xff;
+	devfn = pcidev_info->pdi_slot_host_handle & 0xffffffff;
+ 	host_pci_bus = pci_find_bus(segment, bus_no);
+ 	host_pci_dev = pci_get_slot(host_pci_bus, devfn);
+
+	pcidev_info->host_pci_dev = host_pci_dev;
+	pcidev_info->pdi_linux_pcidev = dev;
+	pcidev_info->pdi_host_pcidev_info = SN_PCIDEV_INFO(host_pci_dev);
+	bs = SN_PCIBUS_BUSSOFT(dev->bus);
+	pcidev_info->pdi_pcibus_info = bs;
+
+	if (bs && bs->bs_asic_type < PCIIO_ASIC_MAX_TYPES) {
+		SN_PCIDEV_BUSPROVIDER(dev) = sn_pci_provider[bs->bs_asic_type];
+	} else {
+		SN_PCIDEV_BUSPROVIDER(dev) = &sn_pci_default_provider;
+	}
+
+	/* Only set up IRQ stuff if this device has a host bus context */
+	if (bs && sn_irq_info->irq_irq) {
+		pcidev_info->pdi_sn_irq_info = sn_irq_info;
+		dev->irq = pcidev_info->pdi_sn_irq_info->irq_irq;
+		sn_irq_fixup(dev, sn_irq_info);
+	} else {
+		pcidev_info->pdi_sn_irq_info = NULL;
+		kfree(sn_irq_info);
+	}
+}
+
+/*
+ * sn_common_bus_fixup - Perform platform specific bus fixup.
+ *			 Execute the ASIC specific fixup routine
+ *			 for this bus.
+ */
+void
+sn_common_bus_fixup(struct pci_bus *bus,
+		    struct pcibus_bussoft *prom_bussoft_ptr)
+{
+	int cnode;
+	struct pci_controller *controller;
+	struct hubdev_info *hubdev_info;
+	int nasid;
+	void *provider_soft;
+	struct sn_pcibus_provider *provider;
+	struct sn_platform_data *sn_platform_data;
+
+	controller = PCI_CONTROLLER(bus);
+	/*
+	 * Per-provider fixup.  Copies the bus soft structure from prom
+	 * to local area and links SN_PCIBUS_BUSSOFT().
+	 */
+
+	if (prom_bussoft_ptr->bs_asic_type >= PCIIO_ASIC_MAX_TYPES) {
+		printk(KERN_WARNING "sn_common_bus_fixup: Unsupported asic type, %d",
+		       prom_bussoft_ptr->bs_asic_type);
+		return;
+	}
+
+	if (prom_bussoft_ptr->bs_asic_type == PCIIO_ASIC_TYPE_PPB)
+		return;	/* no further fixup necessary */
+
+	provider = sn_pci_provider[prom_bussoft_ptr->bs_asic_type];
+	if (provider == NULL)
+		panic("sn_common_bus_fixup: No provider registered for this asic type, %d",
+		      prom_bussoft_ptr->bs_asic_type);
+
+	if (provider->bus_fixup)
+		provider_soft = (*provider->bus_fixup) (prom_bussoft_ptr,
+				 controller);
+	else
+		provider_soft = NULL;
+
+	/*
+	 * Generic bus fixup goes here.  Don't reference prom_bussoft_ptr
+	 * after this point.
+	 */
+	controller->platform_data = kzalloc(sizeof(struct sn_platform_data),
+					    GFP_KERNEL);
+	if (controller->platform_data == NULL)
+		BUG();
+	sn_platform_data =
+			(struct sn_platform_data *) controller->platform_data;
+	sn_platform_data->provider_soft = provider_soft;
+	INIT_LIST_HEAD(&((struct sn_platform_data *)
+			 controller->platform_data)->pcidev_info);
+	nasid = NASID_GET(SN_PCIBUS_BUSSOFT(bus)->bs_base);
+	cnode = nasid_to_cnodeid(nasid);
+	hubdev_info = (struct hubdev_info *)(NODEPDA(cnode)->pdinfo);
+	SN_PCIBUS_BUSSOFT(bus)->bs_xwidget_info =
+	    &(hubdev_info->hdi_xwidget_info[SN_PCIBUS_BUSSOFT(bus)->bs_xid]);
+
+	/*
+	 * If the node information we obtained during the fixup phase is
+	 * invalid then set controller->node to -1 (undetermined)
+	 */
+	if (controller->node >= num_online_nodes()) {
+		struct pcibus_bussoft *b = SN_PCIBUS_BUSSOFT(bus);
+
+		printk(KERN_WARNING "Device ASIC=%u XID=%u PBUSNUM=%u"
+		       "L_IO=%lx L_MEM=%lx BASE=%lx\n",
+		       b->bs_asic_type, b->bs_xid, b->bs_persist_busnum,
+		       b->bs_legacy_io, b->bs_legacy_mem, b->bs_base);
+		printk(KERN_WARNING "on node %d but only %d nodes online."
+		       "Association set to undetermined.\n",
+		       controller->node, num_online_nodes());
+		controller->node = -1;
+	}
+}
+
+void sn_bus_store_sysdata(struct pci_dev *dev)
+{
+	struct sysdata_el *element;
+
+	element = kzalloc(sizeof(struct sysdata_el), GFP_KERNEL);
+	if (!element) {
+		dev_dbg(dev, "%s: out of memory!\n", __FUNCTION__);
+		return;
+	}
+	element->sysdata = SN_PCIDEV_INFO(dev);
+	list_add(&element->entry, &sn_sysdata_list);
+}
+
+void sn_bus_free_sysdata(void)
+{
+	struct sysdata_el *element;
+	struct list_head *list, *safe;
+
+	list_for_each_safe(list, safe, &sn_sysdata_list) {
+		element = list_entry(list, struct sysdata_el, entry);
+		list_del(&element->entry);
+		list_del(&(((struct pcidev_info *)
+			     (element->sysdata))->pdi_list));
+		kfree(element->sysdata);
+		kfree(element);
+	}
+	return;
+}
+
+/*
+ * hubdev_init_node() - Creates the HUB data structure and link them to it's
+ *			own NODE specific data area.
+ */
+void hubdev_init_node(nodepda_t * npda, cnodeid_t node)
+{
+	struct hubdev_info *hubdev_info;
+	int size;
+	pg_data_t *pg;
+
+	size = sizeof(struct hubdev_info);
+
+	if (node >= num_online_nodes())	/* Headless/memless IO nodes */
+		pg = NODE_DATA(0);
+	else
+		pg = NODE_DATA(node);
+
+	hubdev_info = (struct hubdev_info *)alloc_bootmem_node(pg, size);
+
+	npda->pdinfo = (void *)hubdev_info;
+}
+
+geoid_t
+cnodeid_get_geoid(cnodeid_t cnode)
+{
+	struct hubdev_info *hubdev;
+
+	hubdev = (struct hubdev_info *)(NODEPDA(cnode)->pdinfo);
+	return hubdev->hdi_geoid;
+}
+
+void sn_generate_path(struct pci_bus *pci_bus, char *address)
+{
+	nasid_t nasid;
+	cnodeid_t cnode;
+	geoid_t geoid;
+	moduleid_t moduleid;
+	u16 bricktype;
+
+	nasid = NASID_GET(SN_PCIBUS_BUSSOFT(pci_bus)->bs_base);
+	cnode = nasid_to_cnodeid(nasid);
+	geoid = cnodeid_get_geoid(cnode);
+	moduleid = geo_module(geoid);
+
+	sprintf(address, "module_%c%c%c%c%.2d",
+		'0'+RACK_GET_CLASS(MODULE_GET_RACK(moduleid)),
+		'0'+RACK_GET_GROUP(MODULE_GET_RACK(moduleid)),
+		'0'+RACK_GET_NUM(MODULE_GET_RACK(moduleid)),
+		MODULE_GET_BTCHAR(moduleid), MODULE_GET_BPOS(moduleid));
+
+	/* Tollhouse requires slot id to be displayed */
+	bricktype = MODULE_GET_BTYPE(moduleid);
+	if ((bricktype == L1_BRICKTYPE_191010) ||
+	    (bricktype == L1_BRICKTYPE_1932))
+			sprintf(address, "%s^%d", address, geo_slot(geoid));
+}
+
+/*
+ * sn_pci_fixup_bus() - Perform SN specific setup of software structs
+ *			(pcibus_bussoft, pcidev_info) and hardware
+ *			registers, for the specified bus and devices under it.
+ */
+void __devinit
+sn_pci_fixup_bus(struct pci_bus *bus)
+{
+
+	if (SN_ACPI_BASE_SUPPORT())
+		sn_acpi_bus_fixup(bus);
+	else
+		sn_bus_fixup(bus);
+}
+
+/*
+ * sn_io_early_init - Perform early IO (and some non-IO) initialization.
+ *		      In particular, setup the sn_pci_provider[] array.
+ *		      This needs to be done prior to any bus scanning
+ *		      (acpi_scan_init()) in the ACPI case, as the SN
+ *		      bus fixup code will reference the array.
+ */
+static int __init
+sn_io_early_init(void)
+{
+	int i;
+
+	if (!ia64_platform_is("sn2") || IS_RUNNING_ON_FAKE_PROM())
+		return 0;
+
+	/*
+	 * prime sn_pci_provider[].  Individial provider init routines will
+	 * override their respective default entries.
+	 */
+
+	for (i = 0; i < PCIIO_ASIC_MAX_TYPES; i++)
+		sn_pci_provider[i] = &sn_pci_default_provider;
+
+	pcibr_init_provider();
+	tioca_init_provider();
+	tioce_init_provider();
+
+	/*
+	 * This is needed to avoid bounce limit checks in the blk layer
+	 */
+	ia64_max_iommu_merge_mask = ~PAGE_MASK;
+
+	sn_irq_lh_init();
+	INIT_LIST_HEAD(&sn_sysdata_list);
+	sn_init_cpei_timer();
+
+#ifdef CONFIG_PROC_FS
+	register_sn_procfs();
+#endif
+
+	printk(KERN_INFO "ACPI  DSDT OEM Rev 0x%x\n",
+	       acpi_gbl_DSDT->oem_revision);
+	if (SN_ACPI_BASE_SUPPORT())
+		sn_io_acpi_init();
+	else
+		sn_io_init();
+	return 0;
+}
+
+arch_initcall(sn_io_early_init);
+
+/*
+ * sn_io_late_init() - Perform any final platform specific IO initialization.
+ */
+
+int __init
+sn_io_late_init(void)
+{
+	struct pci_bus *bus;
+	struct pcibus_bussoft *bussoft;
+	cnodeid_t cnode;
+	nasid_t nasid;
+	cnodeid_t near_cnode;
+
+	if (!ia64_platform_is("sn2") || IS_RUNNING_ON_FAKE_PROM())
+		return 0;
+
+	/*
+	 * Setup closest node in pci_controller->node for
+	 * PIC, TIOCP, TIOCE (TIOCA does it during bus fixup using
+	 * info from the PROM).
+	 */
+	bus = NULL;
+	while ((bus = pci_find_next_bus(bus)) != NULL) {
+		bussoft = SN_PCIBUS_BUSSOFT(bus);
+		nasid = NASID_GET(bussoft->bs_base);
+		cnode = nasid_to_cnodeid(nasid);
+		if ((bussoft->bs_asic_type == PCIIO_ASIC_TYPE_TIOCP) ||
+		    (bussoft->bs_asic_type == PCIIO_ASIC_TYPE_TIOCE)) {
+			/* TIO PCI Bridge: find nearest node with CPUs */
+			int e = sn_hwperf_get_nearest_node(cnode, NULL,
+							   &near_cnode);
+			if (e < 0) {
+				near_cnode = (cnodeid_t)-1; /* use any node */
+				printk(KERN_WARNING "pcibr_bus_fixup: failed "
+				       "to find near node with CPUs to TIO "
+				       "node %d, err=%d\n", cnode, e);
+			}
+			PCI_CONTROLLER(bus)->node = near_cnode;
+		} else if (bussoft->bs_asic_type == PCIIO_ASIC_TYPE_PIC) {
+			PCI_CONTROLLER(bus)->node = cnode;
+		}
+	}
+
+	sn_ioif_inited = 1;	/* SN I/O infrastructure now initialized */
+
+	return 0;
+}
+
+fs_initcall(sn_io_late_init);
+
+EXPORT_SYMBOL(sn_pci_fixup_slot);
+EXPORT_SYMBOL(sn_pci_unfixup_slot);
+EXPORT_SYMBOL(sn_bus_store_sysdata);
+EXPORT_SYMBOL(sn_bus_free_sysdata);
+EXPORT_SYMBOL(sn_generate_path);
+
diff --git a/arch/ia64/sn/kernel/io_init.c b/arch/ia64/sn/kernel/io_init.c
index dc09a6a..9ad843e 100644
--- a/arch/ia64/sn/kernel/io_init.c
+++ b/arch/ia64/sn/kernel/io_init.c
@@ -3,103 +3,28 @@
  * License.  See the file "COPYING" in the main directory of this archive
  * for more details.
  *
- * Copyright (C) 1992 - 1997, 2000-2005 Silicon Graphics, Inc. All rights reserved.
+ * Copyright (C) 1992 - 1997, 2000-2006 Silicon Graphics, Inc. All rights reserved.
  */
 
-#include <linux/bootmem.h>
-#include <linux/nodemask.h>
 #include <asm/sn/types.h>
 #include <asm/sn/addrs.h>
-#include <asm/sn/sn_feature_sets.h>
-#include <asm/sn/geo.h>
 #include <asm/sn/io.h>
-#include <asm/sn/l1.h>
 #include <asm/sn/module.h>
-#include <asm/sn/pcibr_provider.h>
+#include <asm/sn/intr.h>
 #include <asm/sn/pcibus_provider_defs.h>
 #include <asm/sn/pcidev.h>
-#include <asm/sn/simulator.h>
 #include <asm/sn/sn_sal.h>
-#include <asm/sn/tioca_provider.h>
-#include <asm/sn/tioce_provider.h>
 #include "xtalk/hubdev.h"
-#include "xtalk/xwidgetdev.h"
 
-
-extern void sn_init_cpei_timer(void);
-extern void register_sn_procfs(void);
-
-static struct list_head sn_sysdata_list;
-
-/* sysdata list struct */
-struct sysdata_el {
-	struct list_head entry;
-	void *sysdata;
-};
-
-struct slab_info {
-	struct hubdev_info hubdev;
-};
-
-struct brick {
-	moduleid_t id;		/* Module ID of this module        */
-	struct slab_info slab_info[MAX_SLABS + 1];
-};
-
-int sn_ioif_inited;		/* SN I/O infrastructure initialized? */
-
-struct sn_pcibus_provider *sn_pci_provider[PCIIO_ASIC_MAX_TYPES];	/* indexed by asic type */
+/*
+ * The code in this file will only be executed when running with
+ * a PROM that does _not_ have base ACPI IO support.
+ * (i.e., SN_ACPI_BASE_SUPPORT() == 0)
+ */
 
 static int max_segment_number;		 /* Default highest segment number */
 static int max_pcibus_number = 255;	/* Default highest pci bus number */
 
-/*
- * Hooks and struct for unsupported pci providers
- */
-
-static dma_addr_t
-sn_default_pci_map(struct pci_dev *pdev, unsigned long paddr, size_t size, int type)
-{
-	return 0;
-}
-
-static void
-sn_default_pci_unmap(struct pci_dev *pdev, dma_addr_t addr, int direction)
-{
-	return;
-}
-
-static void *
-sn_default_pci_bus_fixup(struct pcibus_bussoft *soft, struct pci_controller *controller)
-{
-	return NULL;
-}
-
-static struct sn_pcibus_provider sn_pci_default_provider = {
-	.dma_map = sn_default_pci_map,
-	.dma_map_consistent = sn_default_pci_map,
-	.dma_unmap = sn_default_pci_unmap,
-	.bus_fixup = sn_default_pci_bus_fixup,
-};
-
-/*
- * Retrieve the DMA Flush List given nasid, widget, and device.
- * This list is needed to implement the WAR - Flush DMA data on PIO Reads.
- */
-static inline u64
-sal_get_device_dmaflush_list(u64 nasid, u64 widget_num, u64 device_num,
-			     u64 address)
-{
-	struct ia64_sal_retval ret_stuff;
-	ret_stuff.status = 0;
-	ret_stuff.v0 = 0;
-
-	SAL_CALL_NOLOCK(ret_stuff,
-			(u64) SN_SAL_IOIF_GET_DEVICE_DMAFLUSH_LIST,
-			(u64) nasid, (u64) widget_num,
-			(u64) device_num, (u64) address, 0, 0, 0);
-	return ret_stuff.status;
-}
 
 /*
  * Retrieve the hub device info structure for the given nasid.
@@ -131,93 +56,20 @@
 	return ret_stuff.v0;
 }
 
-/*
- * Retrieve the pci device information given the bus and device|function number.
- */
-static inline u64
-sal_get_pcidev_info(u64 segment, u64 bus_number, u64 devfn, u64 pci_dev,
-		    u64 sn_irq_info)
-{
-	struct ia64_sal_retval ret_stuff;
-	ret_stuff.status = 0;
-	ret_stuff.v0 = 0;
-
-	SAL_CALL_NOLOCK(ret_stuff,
-			(u64) SN_SAL_IOIF_GET_PCIDEV_INFO,
-			(u64) segment, (u64) bus_number, (u64) devfn,
-			(u64) pci_dev,
-			sn_irq_info, 0, 0);
-	return ret_stuff.v0;
-}
 
 /*
- * sn_pcidev_info_get() - Retrieve the pcidev_info struct for the specified
- *			  device.
- */
-inline struct pcidev_info *
-sn_pcidev_info_get(struct pci_dev *dev)
-{
-	struct pcidev_info *pcidev;
-
-	list_for_each_entry(pcidev,
-			    &(SN_PCI_CONTROLLER(dev)->pcidev_info), pdi_list) {
-		if (pcidev->pdi_linux_pcidev == dev) {
-			return pcidev;
-		}
-	}
-	return NULL;
-}
-
-/* Older PROM flush WAR
- *
- * 01/16/06 -- This war will be in place until a new official PROM is released.
- * Additionally note that the struct sn_flush_device_war also has to be
- * removed from arch/ia64/sn/include/xtalk/hubdev.h
- */
-static u8 war_implemented = 0;
-
-static s64 sn_device_fixup_war(u64 nasid, u64 widget, int device,
-			       struct sn_flush_device_common *common)
-{
-	struct sn_flush_device_war *war_list;
-	struct sn_flush_device_war *dev_entry;
-	struct ia64_sal_retval isrv = {0,0,0,0};
-
-	if (!war_implemented) {
-		printk(KERN_WARNING "PROM version < 4.50 -- implementing old "
-		       "PROM flush WAR\n");
-		war_implemented = 1;
-	}
-
-	war_list = kzalloc(DEV_PER_WIDGET * sizeof(*war_list), GFP_KERNEL);
-	if (!war_list)
-		BUG();
-
-	SAL_CALL_NOLOCK(isrv, SN_SAL_IOIF_GET_WIDGET_DMAFLUSH_LIST,
-			nasid, widget, __pa(war_list), 0, 0, 0 ,0);
-	if (isrv.status)
-		panic("sn_device_fixup_war failed: %s\n",
-		      ia64_sal_strerror(isrv.status));
-
-	dev_entry = war_list + device;
-	memcpy(common,dev_entry, sizeof(*common));
-	kfree(war_list);
-
-	return isrv.status;
-}
-
-/*
- * sn_fixup_ionodes() - This routine initializes the HUB data strcuture for
- *	each node in the system.
+ * sn_fixup_ionodes() - This routine initializes the HUB data structure for
+ *			each node in the system. This function is only
+ *			executed when running with a non-ACPI capable PROM.
  */
 static void __init sn_fixup_ionodes(void)
 {
-	struct sn_flush_device_kernel *sn_flush_device_kernel;
-	struct sn_flush_device_kernel *dev_entry;
+
 	struct hubdev_info *hubdev;
 	u64 status;
 	u64 nasid;
-	int i, widget, device, size;
+	int i;
+	extern void sn_common_hubdev_init(struct hubdev_info *);
 
 	/*
 	 * Get SGI Specific HUB chipset information.
@@ -240,70 +92,47 @@
 			max_segment_number = hubdev->max_segment_number;
 			max_pcibus_number = hubdev->max_pcibus_number;
 		}
-
-		/* Attach the error interrupt handlers */
-		if (nasid & 1)
-			ice_error_init(hubdev);
-		else
-			hub_error_init(hubdev);
-
-		for (widget = 0; widget <= HUB_WIDGET_ID_MAX; widget++)
-			hubdev->hdi_xwidget_info[widget].xwi_hubinfo = hubdev;
-
-		if (!hubdev->hdi_flush_nasid_list.widget_p)
-			continue;
-
-		size = (HUB_WIDGET_ID_MAX + 1) *
-			sizeof(struct sn_flush_device_kernel *);
-		hubdev->hdi_flush_nasid_list.widget_p =
-			kzalloc(size, GFP_KERNEL);
-		if (!hubdev->hdi_flush_nasid_list.widget_p)
-			BUG();
-
-		for (widget = 0; widget <= HUB_WIDGET_ID_MAX; widget++) {
-			size = DEV_PER_WIDGET *
-				sizeof(struct sn_flush_device_kernel);
-			sn_flush_device_kernel = kzalloc(size, GFP_KERNEL);
-			if (!sn_flush_device_kernel)
-				BUG();
-
-			dev_entry = sn_flush_device_kernel;
-			for (device = 0; device < DEV_PER_WIDGET;
-			     device++,dev_entry++) {
-				size = sizeof(struct sn_flush_device_common);
-				dev_entry->common = kzalloc(size, GFP_KERNEL);
-				if (!dev_entry->common)
-					BUG();
-
-				if (sn_prom_feature_available(
-						       PRF_DEVICE_FLUSH_LIST))
-					status = sal_get_device_dmaflush_list(
-						     nasid, widget, device,
-						     (u64)(dev_entry->common));
-				else
-					status = sn_device_fixup_war(nasid,
-						     widget, device,
-						     dev_entry->common);
-				if (status != SALRET_OK)
-					panic("SAL call failed: %s\n",
-					      ia64_sal_strerror(status));
-
-				spin_lock_init(&dev_entry->sfdl_flush_lock);
-			}
-
-			if (sn_flush_device_kernel)
-				hubdev->hdi_flush_nasid_list.widget_p[widget] =
-						       sn_flush_device_kernel;
-	        }
+		sn_common_hubdev_init(hubdev);
 	}
 }
 
 /*
+ * sn_pci_legacy_window_fixup - Create PCI controller windows for
+ *				legacy IO and MEM space. This needs to
+ *				be done here, as the PROM does not have
+ *				ACPI support defining the root buses
+ *				and their resources (_CRS),
+ */
+static void
+sn_legacy_pci_window_fixup(struct pci_controller *controller,
+			   u64 legacy_io, u64 legacy_mem)
+{
+		controller->window = kcalloc(2, sizeof(struct pci_window),
+					     GFP_KERNEL);
+		if (controller->window == NULL)
+			BUG();
+		controller->window[0].offset = legacy_io;
+		controller->window[0].resource.name = "legacy_io";
+		controller->window[0].resource.flags = IORESOURCE_IO;
+		controller->window[0].resource.start = legacy_io;
+		controller->window[0].resource.end =
+	    			controller->window[0].resource.start + 0xffff;
+		controller->window[0].resource.parent = &ioport_resource;
+		controller->window[1].offset = legacy_mem;
+		controller->window[1].resource.name = "legacy_mem";
+		controller->window[1].resource.flags = IORESOURCE_MEM;
+		controller->window[1].resource.start = legacy_mem;
+		controller->window[1].resource.end =
+	    	       controller->window[1].resource.start + (1024 * 1024) - 1;
+		controller->window[1].resource.parent = &iomem_resource;
+		controller->windows = 2;
+}
+
+/*
  * sn_pci_window_fixup() - Create a pci_window for each device resource.
- *			   Until ACPI support is added, we need this code
- *			   to setup pci_windows for use by
- *			   pcibios_bus_to_resource(),
- *			   pcibios_resource_to_bus(), etc.
+ *			   It will setup pci_windows for use by
+ *			   pcibios_bus_to_resource(), pcibios_resource_to_bus(),
+ *			   etc.
  */
 static void
 sn_pci_window_fixup(struct pci_dev *dev, unsigned int count,
@@ -342,60 +171,22 @@
 	controller->window = new_window;
 }
 
-void sn_pci_unfixup_slot(struct pci_dev *dev)
-{
-	struct pci_dev *host_pci_dev = SN_PCIDEV_INFO(dev)->host_pci_dev;
-
-	sn_irq_unfixup(dev);
-	pci_dev_put(host_pci_dev);
-	pci_dev_put(dev);
-}
-
 /*
- * sn_pci_fixup_slot() - This routine sets up a slot's resources
- * consistent with the Linux PCI abstraction layer.  Resources acquired
- * from our PCI provider include PIO maps to BAR space and interrupt
- * objects.
+ * sn_more_slot_fixup() - We are not running with an ACPI capable PROM,
+ *			  and need to convert the pci_dev->resource
+ *			  'start' and 'end' addresses to mapped addresses,
+ *			  and setup the pci_controller->window array entries.
  */
-void sn_pci_fixup_slot(struct pci_dev *dev)
+void
+sn_more_slot_fixup(struct pci_dev *dev, struct pcidev_info *pcidev_info)
 {
 	unsigned int count = 0;
 	int idx;
-	int segment = pci_domain_nr(dev->bus);
-	int status = 0;
-	struct pcibus_bussoft *bs;
- 	struct pci_bus *host_pci_bus;
- 	struct pci_dev *host_pci_dev;
-	struct pcidev_info *pcidev_info;
 	s64 pci_addrs[PCI_ROM_RESOURCE + 1];
- 	struct sn_irq_info *sn_irq_info;
- 	unsigned long size;
- 	unsigned int bus_no, devfn;
-
-	pci_dev_get(dev); /* for the sysdata pointer */
-	pcidev_info = kzalloc(sizeof(struct pcidev_info), GFP_KERNEL);
-	if (!pcidev_info)
-		BUG();		/* Cannot afford to run out of memory */
-
-	sn_irq_info = kzalloc(sizeof(struct sn_irq_info), GFP_KERNEL);
-	if (!sn_irq_info)
-		BUG();		/* Cannot afford to run out of memory */
-
-	/* Call to retrieve pci device information needed by kernel. */
-	status = sal_get_pcidev_info((u64) segment, (u64) dev->bus->number, 
-				     dev->devfn,
-				     (u64) __pa(pcidev_info),
-				     (u64) __pa(sn_irq_info));
-	if (status)
-		BUG(); /* Cannot get platform pci device information */
-
-	/* Add pcidev_info to list in sn_pci_controller struct */
-	list_add_tail(&pcidev_info->pdi_list,
-		      &(SN_PCI_CONTROLLER(dev->bus)->pcidev_info));
+	unsigned long addr, end, size, start;
 
 	/* Copy over PIO Mapped Addresses */
 	for (idx = 0; idx <= PCI_ROM_RESOURCE; idx++) {
-		unsigned long start, end, addr;
 
 		if (!pcidev_info->pdi_pio_mapped_addr[idx]) {
 			pci_addrs[idx] = -1;
@@ -419,60 +210,28 @@
 			dev->resource[idx].parent = &ioport_resource;
 		else
 			dev->resource[idx].parent = &iomem_resource;
+		/* If ROM, mark as shadowed in PROM */
+		if (idx == PCI_ROM_RESOURCE)
+			dev->resource[idx].flags |= IORESOURCE_ROM_BIOS_COPY;
 	}
 	/* Create a pci_window in the pci_controller struct for
 	 * each device resource.
 	 */
 	if (count > 0)
 		sn_pci_window_fixup(dev, count, pci_addrs);
-
-	/*
-	 * Using the PROMs values for the PCI host bus, get the Linux
- 	 * PCI host_pci_dev struct and set up host bus linkages
- 	 */
-
-	bus_no = (pcidev_info->pdi_slot_host_handle >> 32) & 0xff;
-	devfn = pcidev_info->pdi_slot_host_handle & 0xffffffff;
- 	host_pci_bus = pci_find_bus(segment, bus_no);
- 	host_pci_dev = pci_get_slot(host_pci_bus, devfn);
-
-	pcidev_info->host_pci_dev = host_pci_dev;
-	pcidev_info->pdi_linux_pcidev = dev;
-	pcidev_info->pdi_host_pcidev_info = SN_PCIDEV_INFO(host_pci_dev);
-	bs = SN_PCIBUS_BUSSOFT(dev->bus);
-	pcidev_info->pdi_pcibus_info = bs;
-
-	if (bs && bs->bs_asic_type < PCIIO_ASIC_MAX_TYPES) {
-		SN_PCIDEV_BUSPROVIDER(dev) = sn_pci_provider[bs->bs_asic_type];
-	} else {
-		SN_PCIDEV_BUSPROVIDER(dev) = &sn_pci_default_provider;
-	}
-
-	/* Only set up IRQ stuff if this device has a host bus context */
-	if (bs && sn_irq_info->irq_irq) {
-		pcidev_info->pdi_sn_irq_info = sn_irq_info;
-		dev->irq = pcidev_info->pdi_sn_irq_info->irq_irq;
-		sn_irq_fixup(dev, sn_irq_info);
-	} else {
-		pcidev_info->pdi_sn_irq_info = NULL;
-		kfree(sn_irq_info);
-	}
 }
 
 /*
  * sn_pci_controller_fixup() - This routine sets up a bus's resources
- * consistent with the Linux PCI abstraction layer.
+ *			       consistent with the Linux PCI abstraction layer.
  */
-void sn_pci_controller_fixup(int segment, int busnum, struct pci_bus *bus)
+static void
+sn_pci_controller_fixup(int segment, int busnum, struct pci_bus *bus)
 {
-	int status;
-	int nasid, cnode;
+	s64 status = 0;
 	struct pci_controller *controller;
-	struct sn_pci_controller *sn_controller;
 	struct pcibus_bussoft *prom_bussoft_ptr;
-	struct hubdev_info *hubdev_info;
-	void *provider_soft;
-	struct sn_pcibus_provider *provider;
+
 
  	status = sal_get_pcibus_info((u64) segment, (u64) busnum,
  				     (u64) ia64_tpa(&prom_bussoft_ptr));
@@ -480,261 +239,77 @@
 		return;		/*bus # does not exist */
 	prom_bussoft_ptr = __va(prom_bussoft_ptr);
 
-	/* Allocate a sn_pci_controller, which has a pci_controller struct
-	 * as the first member.
-	 */
-	sn_controller = kzalloc(sizeof(struct sn_pci_controller), GFP_KERNEL);
-	if (!sn_controller)
+	controller = kzalloc(sizeof(*controller), GFP_KERNEL);
+	if (!controller)
 		BUG();
-	INIT_LIST_HEAD(&sn_controller->pcidev_info);
-	controller = &sn_controller->pci_controller;
 	controller->segment = segment;
 
-	if (bus == NULL) {
- 		bus = pci_scan_bus(busnum, &pci_root_ops, controller);
- 		if (bus == NULL)
- 			goto error_return; /* error, or bus already scanned */
- 		bus->sysdata = NULL;
-	}
-
-	if (bus->sysdata)
-		goto error_return; /* sysdata already alloc'd */
-
 	/*
-	 * Per-provider fixup.  Copies the contents from prom to local
-	 * area and links SN_PCIBUS_BUSSOFT().
+	 * Temporarily save the prom_bussoft_ptr for use by sn_bus_fixup().
+	 * (platform_data will be overwritten later in sn_common_bus_fixup())
 	 */
+	controller->platform_data = prom_bussoft_ptr;
 
-	if (prom_bussoft_ptr->bs_asic_type >= PCIIO_ASIC_MAX_TYPES)
-		goto error_return; /* unsupported asic type */
-
-	if (prom_bussoft_ptr->bs_asic_type == PCIIO_ASIC_TYPE_PPB)
-		goto error_return; /* no further fixup necessary */
-
-	provider = sn_pci_provider[prom_bussoft_ptr->bs_asic_type];
-	if (provider == NULL)
-		goto error_return; /* no provider registerd for this asic */
+	bus = pci_scan_bus(busnum, &pci_root_ops, controller);
+ 	if (bus == NULL)
+ 		goto error_return; /* error, or bus already scanned */
 
 	bus->sysdata = controller;
-	if (provider->bus_fixup)
-		provider_soft = (*provider->bus_fixup) (prom_bussoft_ptr, controller);
-	else
-		provider_soft = NULL;
 
-	if (provider_soft == NULL) {
-		/* fixup failed or not applicable */
-		bus->sysdata = NULL;
-		goto error_return;
-	}
-
-	/*
-	 * Setup pci_windows for legacy IO and MEM space.
-	 * (Temporary until ACPI support is in place.)
-	 */
-	controller->window = kcalloc(2, sizeof(struct pci_window), GFP_KERNEL);
-	if (controller->window == NULL)
-		BUG();
-	controller->window[0].offset = prom_bussoft_ptr->bs_legacy_io;
-	controller->window[0].resource.name = "legacy_io";
-	controller->window[0].resource.flags = IORESOURCE_IO;
-	controller->window[0].resource.start = prom_bussoft_ptr->bs_legacy_io;
-	controller->window[0].resource.end =
-	    controller->window[0].resource.start + 0xffff;
-	controller->window[0].resource.parent = &ioport_resource;
-	controller->window[1].offset = prom_bussoft_ptr->bs_legacy_mem;
-	controller->window[1].resource.name = "legacy_mem";
-	controller->window[1].resource.flags = IORESOURCE_MEM;
-	controller->window[1].resource.start = prom_bussoft_ptr->bs_legacy_mem;
-	controller->window[1].resource.end =
-	    controller->window[1].resource.start + (1024 * 1024) - 1;
-	controller->window[1].resource.parent = &iomem_resource;
-	controller->windows = 2;
-
-	/*
-	 * Generic bus fixup goes here.  Don't reference prom_bussoft_ptr
-	 * after this point.
-	 */
-
-	PCI_CONTROLLER(bus)->platform_data = provider_soft;
-	nasid = NASID_GET(SN_PCIBUS_BUSSOFT(bus)->bs_base);
-	cnode = nasid_to_cnodeid(nasid);
-	hubdev_info = (struct hubdev_info *)(NODEPDA(cnode)->pdinfo);
-	SN_PCIBUS_BUSSOFT(bus)->bs_xwidget_info =
-	    &(hubdev_info->hdi_xwidget_info[SN_PCIBUS_BUSSOFT(bus)->bs_xid]);
-
-	/*
-	 * If the node information we obtained during the fixup phase is invalid
-	 * then set controller->node to -1 (undetermined)
-	 */
-	if (controller->node >= num_online_nodes()) {
-		struct pcibus_bussoft *b = SN_PCIBUS_BUSSOFT(bus);
-
-		printk(KERN_WARNING "Device ASIC=%u XID=%u PBUSNUM=%u"
-				    "L_IO=%lx L_MEM=%lx BASE=%lx\n",
-			b->bs_asic_type, b->bs_xid, b->bs_persist_busnum,
-			b->bs_legacy_io, b->bs_legacy_mem, b->bs_base);
-		printk(KERN_WARNING "on node %d but only %d nodes online."
-			"Association set to undetermined.\n",
-			controller->node, num_online_nodes());
-		controller->node = -1;
-	}
 	return;
 
 error_return:
 
-	kfree(sn_controller);
-	return;
-}
-
-void sn_bus_store_sysdata(struct pci_dev *dev)
-{
-	struct sysdata_el *element;
-
-	element = kzalloc(sizeof(struct sysdata_el), GFP_KERNEL);
-	if (!element) {
-		dev_dbg(dev, "%s: out of memory!\n", __FUNCTION__);
-		return;
-	}
-	element->sysdata = SN_PCIDEV_INFO(dev);
-	list_add(&element->entry, &sn_sysdata_list);
-}
-
-void sn_bus_free_sysdata(void)
-{
-	struct sysdata_el *element;
-	struct list_head *list, *safe;
-
-	list_for_each_safe(list, safe, &sn_sysdata_list) {
-		element = list_entry(list, struct sysdata_el, entry);
-		list_del(&element->entry);
-		list_del(&(((struct pcidev_info *)
-			     (element->sysdata))->pdi_list));
-		kfree(element->sysdata);
-		kfree(element);
-	}
+	kfree(controller);
 	return;
 }
 
 /*
- * Ugly hack to get PCI setup until we have a proper ACPI namespace.
+ * sn_bus_fixup
+ */
+void
+sn_bus_fixup(struct pci_bus *bus)
+{
+	struct pci_dev *pci_dev = NULL;
+	struct pcibus_bussoft *prom_bussoft_ptr;
+	extern void sn_common_bus_fixup(struct pci_bus *,
+					struct pcibus_bussoft *);
+
+
+	if (!bus->parent) {  /* If root bus */
+		prom_bussoft_ptr = PCI_CONTROLLER(bus)->platform_data;
+		if (prom_bussoft_ptr == NULL) {
+			printk(KERN_ERR
+			       "sn_bus_fixup: 0x%04x:0x%02x Unable to "
+			       "obtain prom_bussoft_ptr\n",
+			       pci_domain_nr(bus), bus->number);
+			return;
+		}
+		sn_common_bus_fixup(bus, prom_bussoft_ptr);
+		sn_legacy_pci_window_fixup(PCI_CONTROLLER(bus),
+					   prom_bussoft_ptr->bs_legacy_io,
+					   prom_bussoft_ptr->bs_legacy_mem);
+        }
+        list_for_each_entry(pci_dev, &bus->devices, bus_list) {
+                sn_pci_fixup_slot(pci_dev);
+        }
+
+}
+
+/*
+ * sn_io_init - PROM does not have ACPI support to define nodes or root buses,
+ *		so we need to do things the hard way, including initiating the
+ *		bus scanning ourselves.
  */
 
-#define PCI_BUSES_TO_SCAN 256
-
-static int __init sn_pci_init(void)
+void __init sn_io_init(void)
 {
 	int i, j;
-	struct pci_dev *pci_dev = NULL;
 
-	if (!ia64_platform_is("sn2") || IS_RUNNING_ON_FAKE_PROM())
-		return 0;
-
-	/*
-	 * prime sn_pci_provider[].  Individial provider init routines will
-	 * override their respective default entries.
-	 */
-
-	for (i = 0; i < PCIIO_ASIC_MAX_TYPES; i++)
-		sn_pci_provider[i] = &sn_pci_default_provider;
-
-	pcibr_init_provider();
-	tioca_init_provider();
-	tioce_init_provider();
-
-	/*
-	 * This is needed to avoid bounce limit checks in the blk layer
-	 */
-	ia64_max_iommu_merge_mask = ~PAGE_MASK;
 	sn_fixup_ionodes();
-	sn_irq_lh_init();
-	INIT_LIST_HEAD(&sn_sysdata_list);
-	sn_init_cpei_timer();
-
-#ifdef CONFIG_PROC_FS
-	register_sn_procfs();
-#endif
 
 	/* busses are not known yet ... */
 	for (i = 0; i <= max_segment_number; i++)
 		for (j = 0; j <= max_pcibus_number; j++)
 			sn_pci_controller_fixup(i, j, NULL);
-
-	/*
-	 * Generic Linux PCI Layer has created the pci_bus and pci_dev 
-	 * structures - time for us to add our SN PLatform specific 
-	 * information.
-	 */
-
-	while ((pci_dev =
-		pci_get_device(PCI_ANY_ID, PCI_ANY_ID, pci_dev)) != NULL)
-		sn_pci_fixup_slot(pci_dev);
-
-	sn_ioif_inited = 1;	/* sn I/O infrastructure now initialized */
-
-	return 0;
 }
-
-/*
- * hubdev_init_node() - Creates the HUB data structure and link them to it's 
- *	own NODE specific data area.
- */
-void hubdev_init_node(nodepda_t * npda, cnodeid_t node)
-{
-	struct hubdev_info *hubdev_info;
-	int size;
-	pg_data_t *pg;
-
-	size = sizeof(struct hubdev_info);
-
-	if (node >= num_online_nodes())	/* Headless/memless IO nodes */
-		pg = NODE_DATA(0);
-	else
-		pg = NODE_DATA(node);
-
-	hubdev_info = (struct hubdev_info *)alloc_bootmem_node(pg, size);
-
-	npda->pdinfo = (void *)hubdev_info;
-}
-
-geoid_t
-cnodeid_get_geoid(cnodeid_t cnode)
-{
-	struct hubdev_info *hubdev;
-
-	hubdev = (struct hubdev_info *)(NODEPDA(cnode)->pdinfo);
-	return hubdev->hdi_geoid;
-}
-
-void sn_generate_path(struct pci_bus *pci_bus, char *address)
-{
-	nasid_t nasid;
-	cnodeid_t cnode;
-	geoid_t geoid;
-	moduleid_t moduleid;
-	u16 bricktype;
-
-	nasid = NASID_GET(SN_PCIBUS_BUSSOFT(pci_bus)->bs_base);
-	cnode = nasid_to_cnodeid(nasid);
-	geoid = cnodeid_get_geoid(cnode);
-	moduleid = geo_module(geoid);
-
-	sprintf(address, "module_%c%c%c%c%.2d",
-		'0'+RACK_GET_CLASS(MODULE_GET_RACK(moduleid)),
-		'0'+RACK_GET_GROUP(MODULE_GET_RACK(moduleid)),
-		'0'+RACK_GET_NUM(MODULE_GET_RACK(moduleid)),
-		MODULE_GET_BTCHAR(moduleid), MODULE_GET_BPOS(moduleid));
-
-	/* Tollhouse requires slot id to be displayed */
-	bricktype = MODULE_GET_BTYPE(moduleid);
-	if ((bricktype == L1_BRICKTYPE_191010) ||
-	    (bricktype == L1_BRICKTYPE_1932))
-			sprintf(address, "%s^%d", address, geo_slot(geoid));
-}
-
-subsys_initcall(sn_pci_init);
-EXPORT_SYMBOL(sn_pci_fixup_slot);
-EXPORT_SYMBOL(sn_pci_unfixup_slot);
-EXPORT_SYMBOL(sn_pci_controller_fixup);
-EXPORT_SYMBOL(sn_bus_store_sysdata);
-EXPORT_SYMBOL(sn_bus_free_sysdata);
-EXPORT_SYMBOL(sn_generate_path);
diff --git a/arch/ia64/sn/kernel/iomv.c b/arch/ia64/sn/kernel/iomv.c
index 7ce3cda..4aa4f30 100644
--- a/arch/ia64/sn/kernel/iomv.c
+++ b/arch/ia64/sn/kernel/iomv.c
@@ -3,10 +3,11 @@
  * License.  See the file "COPYING" in the main directory of this archive
  * for more details.
  *
- * Copyright (C) 2000-2003 Silicon Graphics, Inc. All rights reserved.
+ * Copyright (C) 2000-2003, 2006 Silicon Graphics, Inc. All rights reserved.
  */
 
 #include <linux/module.h>
+#include <linux/acpi.h>
 #include <asm/io.h>
 #include <asm/delay.h>
 #include <asm/vga.h>
@@ -15,6 +16,7 @@
 #include <asm/sn/pda.h>
 #include <asm/sn/sn_cpuid.h>
 #include <asm/sn/shub_mmr.h>
+#include <asm/sn/acpi.h>
 
 #define IS_LEGACY_VGA_IOPORT(p) \
 	(((p) >= 0x3b0 && (p) <= 0x3bb) || ((p) >= 0x3c0 && (p) <= 0x3df))
@@ -31,11 +33,14 @@
 {
 	if (!IS_RUNNING_ON_SIMULATOR()) {
 		if (IS_LEGACY_VGA_IOPORT(port))
-			port += vga_console_iobase;
+			return (__ia64_mk_io_addr(port));
 		/* On sn2, legacy I/O ports don't point at anything */
 		if (port < (64 * 1024))
 			return NULL;
-		return ((void *)(port | __IA64_UNCACHED_OFFSET));
+		if (SN_ACPI_BASE_SUPPORT())
+			return (__ia64_mk_io_addr(port));
+		else
+			return ((void *)(port | __IA64_UNCACHED_OFFSET));
 	} else {
 		/* but the simulator uses them... */
 		unsigned long addr;
diff --git a/arch/ia64/sn/kernel/setup.c b/arch/ia64/sn/kernel/setup.c
index 7a2d824..1d009f9 100644
--- a/arch/ia64/sn/kernel/setup.c
+++ b/arch/ia64/sn/kernel/setup.c
@@ -388,6 +388,14 @@
 	ia64_sn_plat_set_error_handling_features();	// obsolete
 	ia64_sn_set_os_feature(OSF_MCA_SLV_TO_OS_INIT_SLV);
 	ia64_sn_set_os_feature(OSF_FEAT_LOG_SBES);
+	/*
+	 * Note: The calls to notify the PROM of ACPI and PCI Segment
+	 *	 support must be done prior to acpi_load_tables(), as
+	 *	 an ACPI capable PROM will rebuild the DSDT as result
+	 *	 of the call.
+	 */
+	ia64_sn_set_os_feature(OSF_PCISEGMENT_ENABLE);
+	ia64_sn_set_os_feature(OSF_ACPI_ENABLE);
 
 
 #if defined(CONFIG_VT) && defined(CONFIG_VGA_CONSOLE)
@@ -413,6 +421,16 @@
 	if (! vga_console_membase)
 		sn_scan_pcdp();
 
+	/*
+	 *	Setup legacy IO space.
+	 *	vga_console_iobase maps to PCI IO Space address 0 on the
+	 * 	bus containing the VGA console.
+	 */
+	if (vga_console_iobase) {
+		io_space[0].mmio_base = vga_console_iobase;
+		io_space[0].sparse = 0;
+	}
+
 	if (vga_console_membase) {
 		/* usable vga ... make tty0 the preferred default console */
 		if (!strstr(*cmdline_p, "console="))
diff --git a/arch/ia64/sn/kernel/tiocx.c b/arch/ia64/sn/kernel/tiocx.c
index feaf1a6..493380b 100644
--- a/arch/ia64/sn/kernel/tiocx.c
+++ b/arch/ia64/sn/kernel/tiocx.c
@@ -552,7 +552,7 @@
 	bus_unregister(&tiocx_bus_type);
 }
 
-subsys_initcall(tiocx_init);
+fs_initcall(tiocx_init);
 module_exit(tiocx_exit);
 
 /************************************************************************
diff --git a/arch/ia64/sn/pci/pcibr/pcibr_provider.c b/arch/ia64/sn/pci/pcibr/pcibr_provider.c
index 27dd7df..6846dc9 100644
--- a/arch/ia64/sn/pci/pcibr/pcibr_provider.c
+++ b/arch/ia64/sn/pci/pcibr/pcibr_provider.c
@@ -3,7 +3,7 @@
  * License.  See the file "COPYING" in the main directory of this archive
  * for more details.
  *
- * Copyright (C) 2001-2004 Silicon Graphics, Inc. All rights reserved.
+ * Copyright (C) 2001-2004, 2006 Silicon Graphics, Inc. All rights reserved.
  */
 
 #include <linux/interrupt.h>
@@ -109,7 +109,6 @@
 pcibr_bus_fixup(struct pcibus_bussoft *prom_bussoft, struct pci_controller *controller)
 {
 	int nasid, cnode, j;
-	cnodeid_t near_cnode;
 	struct hubdev_info *hubdev_info;
 	struct pcibus_info *soft;
 	struct sn_flush_device_kernel *sn_flush_device_kernel;
@@ -186,20 +185,6 @@
 		return NULL;
 	}
 
-	if (prom_bussoft->bs_asic_type == PCIIO_ASIC_TYPE_TIOCP) {
-		/* TIO PCI Bridge: find nearest node with CPUs */
-		int e = sn_hwperf_get_nearest_node(cnode, NULL, &near_cnode);
-
-		if (e < 0) {
-			near_cnode = (cnodeid_t)-1; /* use any node */
-			printk(KERN_WARNING "pcibr_bus_fixup: failed to find "
-				"near node with CPUs to TIO node %d, err=%d\n",
-				cnode, e);
-		}
-		controller->node = near_cnode;
-	}
-	else
-		controller->node = cnode;
 	return soft;
 }
 
diff --git a/arch/ia64/sn/pci/tioce_provider.c b/arch/ia64/sn/pci/tioce_provider.c
index 46e16dc..35f854f 100644
--- a/arch/ia64/sn/pci/tioce_provider.c
+++ b/arch/ia64/sn/pci/tioce_provider.c
@@ -15,7 +15,6 @@
 #include <asm/sn/pcidev.h>
 #include <asm/sn/pcibus_provider_defs.h>
 #include <asm/sn/tioce_provider.h>
-#include <asm/sn/sn2/sn_hwperf.h>
 
 /*
  * 1/26/2006
@@ -990,8 +989,6 @@
 static void *
 tioce_bus_fixup(struct pcibus_bussoft *prom_bussoft, struct pci_controller *controller)
 {
-	int my_nasid;
-	cnodeid_t my_cnode, mem_cnode;
 	struct tioce_common *tioce_common;
 	struct tioce_kernel *tioce_kern;
 	struct tioce __iomem *tioce_mmr;
@@ -1035,21 +1032,6 @@
 		       tioce_common->ce_pcibus.bs_persist_segment,
 		       tioce_common->ce_pcibus.bs_persist_busnum);
 
-	/*
-	 * identify closest nasid for memory allocations
-	 */
-
-	my_nasid = NASID_GET(tioce_common->ce_pcibus.bs_base);
-	my_cnode = nasid_to_cnodeid(my_nasid);
-
-	if (sn_hwperf_get_nearest_node(my_cnode, &mem_cnode, NULL) < 0) {
-		printk(KERN_WARNING "tioce_bus_fixup: failed to find "
-		       "closest node with MEM to TIO node %d\n", my_cnode);
-		mem_cnode = (cnodeid_t)-1; /* use any node */
-	}
-
-	controller->node = mem_cnode;
-
 	return tioce_common;
 }
 
diff --git a/arch/m68knommu/Kconfig b/arch/m68knommu/Kconfig
index 6d920d4..c1bc22c 100644
--- a/arch/m68knommu/Kconfig
+++ b/arch/m68knommu/Kconfig
@@ -565,7 +565,7 @@
 	depends on ROM
 	help
 	  This is almost always the same as the base of the ROM. Since on all
-	  68000 type varients the vectors are at the base of the boot device
+	  68000 type variants the vectors are at the base of the boot device
 	  on system startup.
 
 config ROMVECSIZE
@@ -574,7 +574,7 @@
 	depends on ROM
 	help
 	  Define the size of the vector region in ROM. For most 68000
-	  varients this would be 0x400 bytes in size. Set to 0 if you do
+	  variants this would be 0x400 bytes in size. Set to 0 if you do
 	  not want a vector region at the start of the ROM.
 
 config ROMSTART
diff --git a/arch/mips/Kconfig b/arch/mips/Kconfig
index 1443024..27f83e6 100644
--- a/arch/mips/Kconfig
+++ b/arch/mips/Kconfig
@@ -266,8 +266,8 @@
 	select BOOT_ELF32
 	select HAVE_STD_PC_SERIAL_PORT
 	select DMA_NONCOHERENT
-	select IRQ_CPU
 	select GENERIC_ISA_DMA
+	select IRQ_CPU
 	select HW_HAS_PCI
 	select I8259
 	select MIPS_BOARDS_GEN
@@ -534,7 +534,7 @@
 	select HW_HAS_EISA
 	select IP22_CPU_SCACHE
 	select IRQ_CPU
-	select NO_ISA if ISA
+	select GENERIC_ISA_DMA_SUPPORT_BROKEN
 	select SWAP_IO_SPACE
 	select SYS_HAS_CPU_R4X00
 	select SYS_HAS_CPU_R5000
@@ -766,6 +766,23 @@
 
 endchoice
 
+config KEXEC
+ 	bool "Kexec system call (EXPERIMENTAL)"
+ 	depends on EXPERIMENTAL
+ 	help
+ 	  kexec is a system call that implements the ability to shutdown your
+ 	  current kernel, and to start another kernel.  It is like a reboot
+ 	  but it is indepedent of the system firmware.   And like a reboot
+ 	  you can start any kernel with it, not just Linux.
+
+ 	  The name comes from the similiarity to the exec system call.
+
+ 	  It is an ongoing process to be certain the hardware in a machine
+ 	  is properly shutdown, so do not be surprised if this code does not
+ 	  initially work for you.  It may help to enable device hotplugging
+ 	  support.  As of this writing the exact hardware interface is
+ 	  strongly in flux, so no good recommendation can be made.
+
 source "arch/mips/ddb5xxx/Kconfig"
 source "arch/mips/gt64120/ev64120/Kconfig"
 source "arch/mips/jazz/Kconfig"
@@ -864,8 +881,11 @@
 config MIPS_DISABLE_OBSOLETE_IDE
 	bool
 
+config GENERIC_ISA_DMA_SUPPORT_BROKEN
+	bool
+
 #
-# Endianess selection.  Suffiently obscure so many users don't know what to
+# Endianess selection.  Sufficiently obscure so many users don't know what to
 # answer,so we try hard to limit the available choices.  Also the use of a
 # choice statement should be more obvious to the user.
 #
@@ -874,7 +894,7 @@
 	help
 	  Some MIPS machines can be configured for either little or big endian
 	  byte order. These modes require different kernels and a different
-	  Linux distribution.  In general there is one prefered byteorder for a
+	  Linux distribution.  In general there is one preferred byteorder for a
 	  particular system but some systems are just as commonly used in the
 	  one or the other endianess.
 
@@ -1835,13 +1855,11 @@
 config ISA
 	bool
 
-config NO_ISA
-	bool
-
 config EISA
 	bool "EISA support"
 	depends on HW_HAS_EISA
 	select ISA
+	select GENERIC_ISA_DMA
 	---help---
 	  The Extended Industry Standard Architecture (EISA) bus was
 	  developed as an open alternative to the IBM MicroChannel bus.
diff --git a/arch/mips/Makefile b/arch/mips/Makefile
index d580d46..641aa30 100644
--- a/arch/mips/Makefile
+++ b/arch/mips/Makefile
@@ -63,9 +63,7 @@
 ifdef CONFIG_BUILD_ELF64
 cflags-y		+= $(call cc-option,-mno-explicit-relocs)
 else
-# -msym32 can not be used for modules since they are loaded into XKSEG
-CFLAGS_MODULE		+= $(call cc-option,-mno-explicit-relocs)
-CFLAGS_KERNEL		+= $(call cc-option,-msym32)
+cflags-y		+= $(call cc-option,-msym32)
 endif
 endif
 
diff --git a/arch/mips/au1000/common/irq.c b/arch/mips/au1000/common/irq.c
index 2abe132..9cf7b671 100644
--- a/arch/mips/au1000/common/irq.c
+++ b/arch/mips/au1000/common/irq.c
@@ -70,7 +70,6 @@
 extern void mips_timer_interrupt(void);
 
 static void setup_local_irq(unsigned int irq, int type, int int_req);
-static unsigned int startup_irq(unsigned int irq);
 static void end_irq(unsigned int irq_nr);
 static inline void mask_and_ack_level_irq(unsigned int irq_nr);
 static inline void mask_and_ack_rise_edge_irq(unsigned int irq_nr);
@@ -84,20 +83,6 @@
 static DEFINE_SPINLOCK(irq_lock);
 
 
-static unsigned int startup_irq(unsigned int irq_nr)
-{
-	local_enable_irq(irq_nr);
-	return 0;
-}
-
-
-static void shutdown_irq(unsigned int irq_nr)
-{
-	local_disable_irq(irq_nr);
-	return;
-}
-
-
 inline void local_enable_irq(unsigned int irq_nr)
 {
 	if (irq_nr > AU1000_LAST_INTC0_INT) {
@@ -249,41 +234,37 @@
 
 static struct irq_chip rise_edge_irq_type = {
 	.typename = "Au1000 Rise Edge",
-	.startup = startup_irq,
-	.shutdown = shutdown_irq,
-	.enable = local_enable_irq,
-	.disable = local_disable_irq,
 	.ack = mask_and_ack_rise_edge_irq,
+	.mask = local_disable_irq,
+	.mask_ack = mask_and_ack_rise_edge_irq,
+	.unmask = local_enable_irq,
 	.end = end_irq,
 };
 
 static struct irq_chip fall_edge_irq_type = {
 	.typename = "Au1000 Fall Edge",
-	.startup = startup_irq,
-	.shutdown = shutdown_irq,
-	.enable = local_enable_irq,
-	.disable = local_disable_irq,
 	.ack = mask_and_ack_fall_edge_irq,
+	.mask = local_disable_irq,
+	.mask_ack = mask_and_ack_fall_edge_irq,
+	.unmask = local_enable_irq,
 	.end = end_irq,
 };
 
 static struct irq_chip either_edge_irq_type = {
 	.typename = "Au1000 Rise or Fall Edge",
-	.startup = startup_irq,
-	.shutdown = shutdown_irq,
-	.enable = local_enable_irq,
-	.disable = local_disable_irq,
 	.ack = mask_and_ack_either_edge_irq,
+	.mask = local_disable_irq,
+	.mask_ack = mask_and_ack_either_edge_irq,
+	.unmask = local_enable_irq,
 	.end = end_irq,
 };
 
 static struct irq_chip level_irq_type = {
 	.typename = "Au1000 Level",
-	.startup = startup_irq,
-	.shutdown = shutdown_irq,
-	.enable = local_enable_irq,
-	.disable = local_disable_irq,
 	.ack = mask_and_ack_level_irq,
+	.mask = local_disable_irq,
+	.mask_ack = mask_and_ack_level_irq,
+	.unmask = local_enable_irq,
 	.end = end_irq,
 };
 
@@ -328,31 +309,31 @@
 				au_writel(1<<(irq_nr-32), IC1_CFG2CLR);
 				au_writel(1<<(irq_nr-32), IC1_CFG1CLR);
 				au_writel(1<<(irq_nr-32), IC1_CFG0SET);
-				irq_desc[irq_nr].chip = &rise_edge_irq_type;
+				set_irq_chip(irq_nr, &rise_edge_irq_type);
 				break;
 			case INTC_INT_FALL_EDGE: /* 0:1:0 */
 				au_writel(1<<(irq_nr-32), IC1_CFG2CLR);
 				au_writel(1<<(irq_nr-32), IC1_CFG1SET);
 				au_writel(1<<(irq_nr-32), IC1_CFG0CLR);
-				irq_desc[irq_nr].chip = &fall_edge_irq_type;
+				set_irq_chip(irq_nr, &fall_edge_irq_type);
 				break;
 			case INTC_INT_RISE_AND_FALL_EDGE: /* 0:1:1 */
 				au_writel(1<<(irq_nr-32), IC1_CFG2CLR);
 				au_writel(1<<(irq_nr-32), IC1_CFG1SET);
 				au_writel(1<<(irq_nr-32), IC1_CFG0SET);
-				irq_desc[irq_nr].chip = &either_edge_irq_type;
+				set_irq_chip(irq_nr, &either_edge_irq_type);
 				break;
 			case INTC_INT_HIGH_LEVEL: /* 1:0:1 */
 				au_writel(1<<(irq_nr-32), IC1_CFG2SET);
 				au_writel(1<<(irq_nr-32), IC1_CFG1CLR);
 				au_writel(1<<(irq_nr-32), IC1_CFG0SET);
-				irq_desc[irq_nr].chip = &level_irq_type;
+				set_irq_chip(irq_nr, &level_irq_type);
 				break;
 			case INTC_INT_LOW_LEVEL: /* 1:1:0 */
 				au_writel(1<<(irq_nr-32), IC1_CFG2SET);
 				au_writel(1<<(irq_nr-32), IC1_CFG1SET);
 				au_writel(1<<(irq_nr-32), IC1_CFG0CLR);
-				irq_desc[irq_nr].chip = &level_irq_type;
+				set_irq_chip(irq_nr, &level_irq_type);
 				break;
 			case INTC_INT_DISABLED: /* 0:0:0 */
 				au_writel(1<<(irq_nr-32), IC1_CFG0CLR);
@@ -380,31 +361,31 @@
 				au_writel(1<<irq_nr, IC0_CFG2CLR);
 				au_writel(1<<irq_nr, IC0_CFG1CLR);
 				au_writel(1<<irq_nr, IC0_CFG0SET);
-				irq_desc[irq_nr].chip = &rise_edge_irq_type;
+				set_irq_chip(irq_nr, &rise_edge_irq_type);
 				break;
 			case INTC_INT_FALL_EDGE: /* 0:1:0 */
 				au_writel(1<<irq_nr, IC0_CFG2CLR);
 				au_writel(1<<irq_nr, IC0_CFG1SET);
 				au_writel(1<<irq_nr, IC0_CFG0CLR);
-				irq_desc[irq_nr].chip = &fall_edge_irq_type;
+				set_irq_chip(irq_nr, &fall_edge_irq_type);
 				break;
 			case INTC_INT_RISE_AND_FALL_EDGE: /* 0:1:1 */
 				au_writel(1<<irq_nr, IC0_CFG2CLR);
 				au_writel(1<<irq_nr, IC0_CFG1SET);
 				au_writel(1<<irq_nr, IC0_CFG0SET);
-				irq_desc[irq_nr].chip = &either_edge_irq_type;
+				set_irq_chip(irq_nr, &either_edge_irq_type);
 				break;
 			case INTC_INT_HIGH_LEVEL: /* 1:0:1 */
 				au_writel(1<<irq_nr, IC0_CFG2SET);
 				au_writel(1<<irq_nr, IC0_CFG1CLR);
 				au_writel(1<<irq_nr, IC0_CFG0SET);
-				irq_desc[irq_nr].chip = &level_irq_type;
+				set_irq_chip(irq_nr, &level_irq_type);
 				break;
 			case INTC_INT_LOW_LEVEL: /* 1:1:0 */
 				au_writel(1<<irq_nr, IC0_CFG2SET);
 				au_writel(1<<irq_nr, IC0_CFG1SET);
 				au_writel(1<<irq_nr, IC0_CFG0CLR);
-				irq_desc[irq_nr].chip = &level_irq_type;
+				set_irq_chip(irq_nr, &level_irq_type);
 				break;
 			case INTC_INT_DISABLED: /* 0:0:0 */
 				au_writel(1<<irq_nr, IC0_CFG0CLR);
diff --git a/arch/mips/au1000/pb1200/board_setup.c b/arch/mips/au1000/pb1200/board_setup.c
index 8b953b9..043302b 100644
--- a/arch/mips/au1000/pb1200/board_setup.c
+++ b/arch/mips/au1000/pb1200/board_setup.c
@@ -55,7 +55,7 @@
 #endif
 
 extern void _board_init_irq(void);
-extern void	(*board_init_irq)(void);
+extern void (*board_init_irq)(void);
 
 void board_reset (void)
 {
@@ -151,11 +151,7 @@
 #endif
 
 	/* Setup Pb1200 External Interrupt Controller */
-	{
-		extern void (*board_init_irq)(void);
-		extern void _board_init_irq(void);
-		board_init_irq = _board_init_irq;
-	}
+	board_init_irq = _board_init_irq;
 }
 
 int
diff --git a/arch/mips/cobalt/irq.c b/arch/mips/cobalt/irq.c
index 82e569d..4c46f0e 100644
--- a/arch/mips/cobalt/irq.c
+++ b/arch/mips/cobalt/irq.c
@@ -45,25 +45,22 @@
 {
 	unsigned int mask, pending, devfn;
 
-	mask = GALILEO_INL(GT_INTRMASK_OFS);
-	pending = GALILEO_INL(GT_INTRCAUSE_OFS) & mask;
+	mask = GT_READ(GT_INTRMASK_OFS);
+	pending = GT_READ(GT_INTRCAUSE_OFS) & mask;
 
-	if (pending & GALILEO_INTR_T0EXP) {
-
-		GALILEO_OUTL(~GALILEO_INTR_T0EXP, GT_INTRCAUSE_OFS);
+	if (pending & GT_INTR_T0EXP_MSK) {
+		GT_WRITE(GT_INTRCAUSE_OFS, ~GT_INTR_T0EXP_MSK);
 		do_IRQ(COBALT_GALILEO_IRQ);
-
-	} else if (pending & GALILEO_INTR_RETRY_CTR) {
-
-		devfn = GALILEO_INL(GT_PCI0_CFGADDR_OFS) >> 8;
-		GALILEO_OUTL(~GALILEO_INTR_RETRY_CTR, GT_INTRCAUSE_OFS);
-		printk(KERN_WARNING "Galileo: PCI retry count exceeded (%02x.%u)\n",
-			PCI_SLOT(devfn), PCI_FUNC(devfn));
-
+	} else if (pending & GT_INTR_RETRYCTR0_MSK) {
+		devfn = GT_READ(GT_PCI0_CFGADDR_OFS) >> 8;
+		GT_WRITE(GT_INTRCAUSE_OFS, ~GT_INTR_RETRYCTR0_MSK);
+		printk(KERN_WARNING
+		       "Galileo: PCI retry count exceeded (%02x.%u)\n",
+		       PCI_SLOT(devfn), PCI_FUNC(devfn));
 	} else {
-
-		GALILEO_OUTL(mask & ~pending, GT_INTRMASK_OFS);
-		printk(KERN_WARNING "Galileo: masking unexpected interrupt %08x\n", pending);
+		GT_WRITE(GT_INTRMASK_OFS, mask & ~pending);
+		printk(KERN_WARNING
+		       "Galileo: masking unexpected interrupt %08x\n", pending);
 	}
 }
 
@@ -104,7 +101,7 @@
 	 * Mask all Galileo interrupts. The Galileo
 	 * handler is set in cobalt_timer_setup()
 	 */
-	GALILEO_OUTL(0, GT_INTRMASK_OFS);
+	GT_WRITE(GT_INTRMASK_OFS, 0);
 
 	init_i8259_irqs();				/*  0 ... 15 */
 	mips_cpu_irq_init(COBALT_CPU_IRQ);		/* 16 ... 23 */
diff --git a/arch/mips/cobalt/setup.c b/arch/mips/cobalt/setup.c
index bf9dc72..e8f0f20 100644
--- a/arch/mips/cobalt/setup.c
+++ b/arch/mips/cobalt/setup.c
@@ -51,23 +51,23 @@
 void __init plat_timer_setup(struct irqaction *irq)
 {
 	/* Load timer value for HZ (TCLK is 50MHz) */
-	GALILEO_OUTL(50*1000*1000 / HZ, GT_TC0_OFS);
+	GT_WRITE(GT_TC0_OFS, 50*1000*1000 / HZ);
 
 	/* Enable timer */
-	GALILEO_OUTL(GALILEO_ENTC0 | GALILEO_SELTC0, GT_TC_CONTROL_OFS);
+	GT_WRITE(GT_TC_CONTROL_OFS, GT_TC_CONTROL_ENTC0_MSK | GT_TC_CONTROL_SELTC0_MSK);
 
 	/* Register interrupt */
 	setup_irq(COBALT_GALILEO_IRQ, irq);
 
 	/* Enable interrupt */
-	GALILEO_OUTL(GALILEO_INTR_T0EXP | GALILEO_INL(GT_INTRMASK_OFS), GT_INTRMASK_OFS);
+	GT_WRITE(GT_INTRMASK_OFS, GT_INTR_T0EXP_MSK | GT_READ(GT_INTRMASK_OFS));
 }
 
 extern struct pci_ops gt64111_pci_ops;
 
 static struct resource cobalt_mem_resource = {
-	.start	= GT64111_MEM_BASE,
-	.end	= GT64111_MEM_END,
+	.start	= GT_DEF_PCI0_MEM0_BASE,
+	.end	= GT_DEF_PCI0_MEM0_BASE + GT_DEF_PCI0_MEM0_SIZE - 1,
 	.name	= "PCI memory",
 	.flags	= IORESOURCE_MEM
 };
@@ -115,7 +115,7 @@
 	.mem_resource	= &cobalt_mem_resource,
 	.mem_offset	= 0,
 	.io_resource	= &cobalt_io_resource,
-	.io_offset	= 0 - GT64111_IO_BASE
+	.io_offset	= 0 - GT_DEF_PCI0_IO_BASE,
 };
 
 void __init plat_mem_setup(void)
@@ -128,7 +128,7 @@
 	_machine_halt = cobalt_machine_halt;
 	pm_power_off = cobalt_machine_power_off;
 
-        set_io_port_base(CKSEG1ADDR(GT64111_IO_BASE));
+	set_io_port_base(CKSEG1ADDR(GT_DEF_PCI0_IO_BASE));
 
 	/* I/O port resource must include UART and LCD/buttons */
 	ioport_resource.end = 0x0fffffff;
@@ -139,7 +139,7 @@
 
         /* Read the cobalt id register out of the PCI config space */
         PCI_CFG_SET(devfn, (VIA_COBALT_BRD_ID_REG & ~0x3));
-        cobalt_board_id = GALILEO_INL(GT_PCI0_CFGDATA_OFS);
+        cobalt_board_id = GT_READ(GT_PCI0_CFGDATA_OFS);
         cobalt_board_id >>= ((VIA_COBALT_BRD_ID_REG & 3) * 8);
         cobalt_board_id = VIA_COBALT_BRD_REG_to_ID(cobalt_board_id);
 
diff --git a/arch/mips/ddb5xxx/ddb5477/irq_5477.c b/arch/mips/ddb5xxx/ddb5477/irq_5477.c
index ba52705..96249aa 100644
--- a/arch/mips/ddb5xxx/ddb5477/irq_5477.c
+++ b/arch/mips/ddb5xxx/ddb5477/irq_5477.c
@@ -53,14 +53,6 @@
 	ll_vrc5477_irq_disable(irq - vrc5477_irq_base);
 }
 
-static unsigned int vrc5477_irq_startup(unsigned int irq)
-{
-	vrc5477_irq_enable(irq);
-	return 0;
-}
-
-#define	vrc5477_irq_shutdown	vrc5477_irq_disable
-
 static void
 vrc5477_irq_ack(unsigned int irq)
 {
@@ -91,11 +83,10 @@
 
 struct irq_chip vrc5477_irq_controller = {
 	.typename = "vrc5477_irq",
-	.startup = vrc5477_irq_startup,
-	.shutdown = vrc5477_irq_shutdown,
-	.enable = vrc5477_irq_enable,
-	.disable = vrc5477_irq_disable,
 	.ack = vrc5477_irq_ack,
+	.mask = vrc5477_irq_disable,
+	.mask_ack = vrc5477_irq_ack,
+	.unmask = vrc5477_irq_enable,
 	.end = vrc5477_irq_end
 };
 
@@ -103,12 +94,8 @@
 {
 	u32 i;
 
-	for (i= irq_base; i< irq_base+ NUM_5477_IRQ; i++) {
-		irq_desc[i].status = IRQ_DISABLED;
-		irq_desc[i].action = NULL;
-		irq_desc[i].depth = 1;
-		irq_desc[i].chip = &vrc5477_irq_controller;
-	}
+	for (i= irq_base; i< irq_base+ NUM_5477_IRQ; i++)
+		set_irq_chip(i, &vrc5477_irq_controller);
 
 	vrc5477_irq_base = irq_base;
 }
diff --git a/arch/mips/dec/ecc-berr.c b/arch/mips/dec/ecc-berr.c
index 3e374d0..c8430c0 100644
--- a/arch/mips/dec/ecc-berr.c
+++ b/arch/mips/dec/ecc-berr.c
@@ -18,7 +18,6 @@
 #include <linux/interrupt.h>
 #include <linux/kernel.h>
 #include <linux/sched.h>
-#include <linux/spinlock.h>
 #include <linux/types.h>
 
 #include <asm/addrspace.h>
@@ -231,13 +230,10 @@
 static inline void dec_kn02_be_init(void)
 {
 	volatile u32 *csr = (void *)CKSEG1ADDR(KN02_SLOT_BASE + KN02_CSR);
-	unsigned long flags;
 
 	kn0x_erraddr = (void *)CKSEG1ADDR(KN02_SLOT_BASE + KN02_ERRADDR);
 	kn0x_chksyn = (void *)CKSEG1ADDR(KN02_SLOT_BASE + KN02_CHKSYN);
 
-	spin_lock_irqsave(&kn02_lock, flags);
-
 	/* Preset write-only bits of the Control Register cache. */
 	cached_kn02_csr = *csr | KN02_CSR_LEDS;
 
@@ -247,8 +243,6 @@
 	cached_kn02_csr |= KN02_CSR_CORRECT;
 	*csr = cached_kn02_csr;
 	iob();
-
-	spin_unlock_irqrestore(&kn02_lock, flags);
 }
 
 static inline void dec_kn03_be_init(void)
diff --git a/arch/mips/dec/int-handler.S b/arch/mips/dec/int-handler.S
index 31dd47d..b251ef8 100644
--- a/arch/mips/dec/int-handler.S
+++ b/arch/mips/dec/int-handler.S
@@ -267,7 +267,7 @@
 		LONG_L	s0, TI_REGS($28)
 		LONG_S	sp, TI_REGS($28)
 		PTR_LA	ra, ret_from_irq
-		j	do_IRQ
+		j	dec_irq_dispatch
 		 nop
 
 #ifdef CONFIG_32BIT
diff --git a/arch/mips/dec/ioasic-irq.c b/arch/mips/dec/ioasic-irq.c
index 41cd2a9..269b22b 100644
--- a/arch/mips/dec/ioasic-irq.c
+++ b/arch/mips/dec/ioasic-irq.c
@@ -13,7 +13,6 @@
 
 #include <linux/init.h>
 #include <linux/irq.h>
-#include <linux/spinlock.h>
 #include <linux/types.h>
 
 #include <asm/dec/ioasic.h>
@@ -21,8 +20,6 @@
 #include <asm/dec/ioasic_ints.h>
 
 
-static DEFINE_SPINLOCK(ioasic_lock);
-
 static int ioasic_irq_base;
 
 
@@ -52,65 +49,31 @@
 	ioasic_write(IO_REG_SIR, sir);
 }
 
-static inline void enable_ioasic_irq(unsigned int irq)
-{
-	unsigned long flags;
-
-	spin_lock_irqsave(&ioasic_lock, flags);
-	unmask_ioasic_irq(irq);
-	spin_unlock_irqrestore(&ioasic_lock, flags);
-}
-
-static inline void disable_ioasic_irq(unsigned int irq)
-{
-	unsigned long flags;
-
-	spin_lock_irqsave(&ioasic_lock, flags);
-	mask_ioasic_irq(irq);
-	spin_unlock_irqrestore(&ioasic_lock, flags);
-}
-
-
-static inline unsigned int startup_ioasic_irq(unsigned int irq)
-{
-	enable_ioasic_irq(irq);
-	return 0;
-}
-
-#define shutdown_ioasic_irq disable_ioasic_irq
-
 static inline void ack_ioasic_irq(unsigned int irq)
 {
-	spin_lock(&ioasic_lock);
 	mask_ioasic_irq(irq);
-	spin_unlock(&ioasic_lock);
 	fast_iob();
 }
 
 static inline void end_ioasic_irq(unsigned int irq)
 {
 	if (!(irq_desc[irq].status & (IRQ_DISABLED | IRQ_INPROGRESS)))
-		enable_ioasic_irq(irq);
+		unmask_ioasic_irq(irq);
 }
 
 static struct irq_chip ioasic_irq_type = {
 	.typename = "IO-ASIC",
-	.startup = startup_ioasic_irq,
-	.shutdown = shutdown_ioasic_irq,
-	.enable = enable_ioasic_irq,
-	.disable = disable_ioasic_irq,
 	.ack = ack_ioasic_irq,
+	.mask = mask_ioasic_irq,
+	.mask_ack = ack_ioasic_irq,
+	.unmask = unmask_ioasic_irq,
 	.end = end_ioasic_irq,
 };
 
 
-#define startup_ioasic_dma_irq startup_ioasic_irq
+#define unmask_ioasic_dma_irq unmask_ioasic_irq
 
-#define shutdown_ioasic_dma_irq shutdown_ioasic_irq
-
-#define enable_ioasic_dma_irq enable_ioasic_irq
-
-#define disable_ioasic_dma_irq disable_ioasic_irq
+#define mask_ioasic_dma_irq mask_ioasic_irq
 
 #define ack_ioasic_dma_irq ack_ioasic_irq
 
@@ -123,11 +86,10 @@
 
 static struct irq_chip ioasic_dma_irq_type = {
 	.typename = "IO-ASIC-DMA",
-	.startup = startup_ioasic_dma_irq,
-	.shutdown = shutdown_ioasic_dma_irq,
-	.enable = enable_ioasic_dma_irq,
-	.disable = disable_ioasic_dma_irq,
 	.ack = ack_ioasic_dma_irq,
+	.mask = mask_ioasic_dma_irq,
+	.mask_ack = ack_ioasic_dma_irq,
+	.unmask = unmask_ioasic_dma_irq,
 	.end = end_ioasic_dma_irq,
 };
 
@@ -140,18 +102,12 @@
 	ioasic_write(IO_REG_SIMR, 0);
 	fast_iob();
 
-	for (i = base; i < base + IO_INR_DMA; i++) {
-		irq_desc[i].status = IRQ_DISABLED;
-		irq_desc[i].action = 0;
-		irq_desc[i].depth = 1;
-		irq_desc[i].chip = &ioasic_irq_type;
-	}
-	for (; i < base + IO_IRQ_LINES; i++) {
-		irq_desc[i].status = IRQ_DISABLED;
-		irq_desc[i].action = 0;
-		irq_desc[i].depth = 1;
-		irq_desc[i].chip = &ioasic_dma_irq_type;
-	}
+	for (i = base; i < base + IO_INR_DMA; i++)
+		set_irq_chip_and_handler(i, &ioasic_irq_type,
+					 handle_level_irq);
+	for (; i < base + IO_IRQ_LINES; i++)
+		set_irq_chip_and_handler(i, &ioasic_dma_irq_type,
+					 handle_level_irq);
 
 	ioasic_irq_base = base;
 }
diff --git a/arch/mips/dec/kn02-irq.c b/arch/mips/dec/kn02-irq.c
index 04a367a..5a9be4c 100644
--- a/arch/mips/dec/kn02-irq.c
+++ b/arch/mips/dec/kn02-irq.c
@@ -14,7 +14,6 @@
 
 #include <linux/init.h>
 #include <linux/irq.h>
-#include <linux/spinlock.h>
 #include <linux/types.h>
 
 #include <asm/dec/kn02.h>
@@ -29,7 +28,6 @@
  * There is no default value -- it has to be initialized.
  */
 u32 cached_kn02_csr;
-DEFINE_SPINLOCK(kn02_lock);
 
 
 static int kn02_irq_base;
@@ -53,54 +51,24 @@
 	*csr = cached_kn02_csr;
 }
 
-static inline void enable_kn02_irq(unsigned int irq)
-{
-	unsigned long flags;
-
-	spin_lock_irqsave(&kn02_lock, flags);
-	unmask_kn02_irq(irq);
-	spin_unlock_irqrestore(&kn02_lock, flags);
-}
-
-static inline void disable_kn02_irq(unsigned int irq)
-{
-	unsigned long flags;
-
-	spin_lock_irqsave(&kn02_lock, flags);
-	mask_kn02_irq(irq);
-	spin_unlock_irqrestore(&kn02_lock, flags);
-}
-
-
-static unsigned int startup_kn02_irq(unsigned int irq)
-{
-	enable_kn02_irq(irq);
-	return 0;
-}
-
-#define shutdown_kn02_irq disable_kn02_irq
-
 static void ack_kn02_irq(unsigned int irq)
 {
-	spin_lock(&kn02_lock);
 	mask_kn02_irq(irq);
-	spin_unlock(&kn02_lock);
 	iob();
 }
 
 static void end_kn02_irq(unsigned int irq)
 {
 	if (!(irq_desc[irq].status & (IRQ_DISABLED | IRQ_INPROGRESS)))
-		enable_kn02_irq(irq);
+		unmask_kn02_irq(irq);
 }
 
 static struct irq_chip kn02_irq_type = {
 	.typename = "KN02-CSR",
-	.startup = startup_kn02_irq,
-	.shutdown = shutdown_kn02_irq,
-	.enable = enable_kn02_irq,
-	.disable = disable_kn02_irq,
 	.ack = ack_kn02_irq,
+	.mask = mask_kn02_irq,
+	.mask_ack = ack_kn02_irq,
+	.unmask = unmask_kn02_irq,
 	.end = end_kn02_irq,
 };
 
@@ -109,22 +77,15 @@
 {
 	volatile u32 *csr = (volatile u32 *)CKSEG1ADDR(KN02_SLOT_BASE +
 						       KN02_CSR);
-	unsigned long flags;
 	int i;
 
 	/* Mask interrupts. */
-	spin_lock_irqsave(&kn02_lock, flags);
 	cached_kn02_csr &= ~KN02_CSR_IOINTEN;
 	*csr = cached_kn02_csr;
 	iob();
-	spin_unlock_irqrestore(&kn02_lock, flags);
 
-	for (i = base; i < base + KN02_IRQ_LINES; i++) {
-		irq_desc[i].status = IRQ_DISABLED;
-		irq_desc[i].action = 0;
-		irq_desc[i].depth = 1;
-		irq_desc[i].chip = &kn02_irq_type;
-	}
+	for (i = base; i < base + KN02_IRQ_LINES; i++)
+		set_irq_chip_and_handler(i, &kn02_irq_type, handle_level_irq);
 
 	kn02_irq_base = base;
 }
diff --git a/arch/mips/dec/setup.c b/arch/mips/dec/setup.c
index 6b7481e..d34032a 100644
--- a/arch/mips/dec/setup.c
+++ b/arch/mips/dec/setup.c
@@ -761,3 +761,9 @@
 	if (dec_interrupt[DEC_IRQ_HALT] >= 0)
 		setup_irq(dec_interrupt[DEC_IRQ_HALT], &haltirq);
 }
+
+asmlinkage unsigned int dec_irq_dispatch(unsigned int irq)
+{
+	do_IRQ(irq);
+	return 0;
+}
diff --git a/arch/mips/dec/time.c b/arch/mips/dec/time.c
index 69e424e..8b7e0c1 100644
--- a/arch/mips/dec/time.c
+++ b/arch/mips/dec/time.c
@@ -151,7 +151,7 @@
 	CMOS_READ(RTC_REG_C);			/* Ack the RTC interrupt.  */
 }
 
-static unsigned int dec_ioasic_hpt_read(void)
+static cycle_t dec_ioasic_hpt_read(void)
 {
 	/*
 	 * The free-running counter is 32-bit which is good for about
@@ -171,7 +171,7 @@
 
 	if (!cpu_has_counter && IOASIC)
 		/* For pre-R4k systems we use the I/O ASIC's counter.  */
-		mips_hpt_read = dec_ioasic_hpt_read;
+		clocksource_mips.read = dec_ioasic_hpt_read;
 
 	/* Set up the rate of periodic DS1287 interrupts.  */
 	CMOS_WRITE(RTC_REF_CLCK_32KHZ | (16 - __ffs(HZ)), RTC_REG_A);
diff --git a/arch/mips/emma2rh/common/irq_emma2rh.c b/arch/mips/emma2rh/common/irq_emma2rh.c
index 197ed4c..59b9829 100644
--- a/arch/mips/emma2rh/common/irq_emma2rh.c
+++ b/arch/mips/emma2rh/common/irq_emma2rh.c
@@ -56,22 +56,6 @@
 	ll_emma2rh_irq_disable(irq - emma2rh_irq_base);
 }
 
-static unsigned int emma2rh_irq_startup(unsigned int irq)
-{
-	emma2rh_irq_enable(irq);
-	return 0;
-}
-
-#define	emma2rh_irq_shutdown	emma2rh_irq_disable
-
-static void emma2rh_irq_ack(unsigned int irq)
-{
-	/* disable interrupt - some handler will re-enable the irq
-	 * and if the interrupt is leveled, we will have infinite loop
-	 */
-	ll_emma2rh_irq_disable(irq - emma2rh_irq_base);
-}
-
 static void emma2rh_irq_end(unsigned int irq)
 {
 	if (!(irq_desc[irq].status & (IRQ_DISABLED | IRQ_INPROGRESS)))
@@ -80,25 +64,20 @@
 
 struct irq_chip emma2rh_irq_controller = {
 	.typename = "emma2rh_irq",
-	.startup = emma2rh_irq_startup,
-	.shutdown = emma2rh_irq_shutdown,
-	.enable = emma2rh_irq_enable,
-	.disable = emma2rh_irq_disable,
-	.ack = emma2rh_irq_ack,
+	.ack = emma2rh_irq_disable,
+	.mask = emma2rh_irq_disable,
+	.mask_ack = emma2rh_irq_disable,
+	.unmask = emma2rh_irq_enable,
 	.end = emma2rh_irq_end,
-	.set_affinity = NULL	/* no affinity stuff for UP */
 };
 
 void emma2rh_irq_init(u32 irq_base)
 {
 	u32 i;
 
-	for (i = irq_base; i < irq_base + NUM_EMMA2RH_IRQ; i++) {
-		irq_desc[i].status = IRQ_DISABLED;
-		irq_desc[i].action = NULL;
-		irq_desc[i].depth = 1;
-		irq_desc[i].chip = &emma2rh_irq_controller;
-	}
+	for (i = irq_base; i < irq_base + NUM_EMMA2RH_IRQ; i++)
+		set_irq_chip_and_handler(i, &emma2rh_irq_controller,
+					 handle_level_irq);
 
 	emma2rh_irq_base = irq_base;
 }
diff --git a/arch/mips/emma2rh/markeins/irq_markeins.c b/arch/mips/emma2rh/markeins/irq_markeins.c
index 0b36eb0..3ac4e40 100644
--- a/arch/mips/emma2rh/markeins/irq_markeins.c
+++ b/arch/mips/emma2rh/markeins/irq_markeins.c
@@ -48,19 +48,6 @@
 	ll_emma2rh_sw_irq_disable(irq - emma2rh_sw_irq_base);
 }
 
-static unsigned int emma2rh_sw_irq_startup(unsigned int irq)
-{
-	emma2rh_sw_irq_enable(irq);
-	return 0;
-}
-
-#define emma2rh_sw_irq_shutdown emma2rh_sw_irq_disable
-
-static void emma2rh_sw_irq_ack(unsigned int irq)
-{
-	ll_emma2rh_sw_irq_disable(irq - emma2rh_sw_irq_base);
-}
-
 static void emma2rh_sw_irq_end(unsigned int irq)
 {
 	if (!(irq_desc[irq].status & (IRQ_DISABLED | IRQ_INPROGRESS)))
@@ -69,25 +56,20 @@
 
 struct irq_chip emma2rh_sw_irq_controller = {
 	.typename = "emma2rh_sw_irq",
-	.startup = emma2rh_sw_irq_startup,
-	.shutdown = emma2rh_sw_irq_shutdown,
-	.enable = emma2rh_sw_irq_enable,
-	.disable = emma2rh_sw_irq_disable,
-	.ack = emma2rh_sw_irq_ack,
+	.ack = emma2rh_sw_irq_disable,
+	.mask = emma2rh_sw_irq_disable,
+	.mask_ack = emma2rh_sw_irq_disable,
+	.unmask = emma2rh_sw_irq_enable,
 	.end = emma2rh_sw_irq_end,
-	.set_affinity = NULL,
 };
 
 void emma2rh_sw_irq_init(u32 irq_base)
 {
 	u32 i;
 
-	for (i = irq_base; i < irq_base + NUM_EMMA2RH_IRQ_SW; i++) {
-		irq_desc[i].status = IRQ_DISABLED;
-		irq_desc[i].action = NULL;
-		irq_desc[i].depth = 2;
-		irq_desc[i].chip = &emma2rh_sw_irq_controller;
-	}
+	for (i = irq_base; i < irq_base + NUM_EMMA2RH_IRQ_SW; i++)
+		set_irq_chip_and_handler(i, &emma2rh_sw_irq_controller,
+					 handle_level_irq);
 
 	emma2rh_sw_irq_base = irq_base;
 }
@@ -126,14 +108,6 @@
 	ll_emma2rh_gpio_irq_disable(irq - emma2rh_gpio_irq_base);
 }
 
-static unsigned int emma2rh_gpio_irq_startup(unsigned int irq)
-{
-	emma2rh_gpio_irq_enable(irq);
-	return 0;
-}
-
-#define emma2rh_gpio_irq_shutdown emma2rh_gpio_irq_disable
-
 static void emma2rh_gpio_irq_ack(unsigned int irq)
 {
 	irq -= emma2rh_gpio_irq_base;
@@ -149,25 +123,19 @@
 
 struct irq_chip emma2rh_gpio_irq_controller = {
 	.typename = "emma2rh_gpio_irq",
-	.startup = emma2rh_gpio_irq_startup,
-	.shutdown = emma2rh_gpio_irq_shutdown,
-	.enable = emma2rh_gpio_irq_enable,
-	.disable = emma2rh_gpio_irq_disable,
 	.ack = emma2rh_gpio_irq_ack,
+	.mask = emma2rh_gpio_irq_disable,
+	.mask_ack = emma2rh_gpio_irq_ack,
+	.unmask = emma2rh_gpio_irq_enable,
 	.end = emma2rh_gpio_irq_end,
-	.set_affinity = NULL,
 };
 
 void emma2rh_gpio_irq_init(u32 irq_base)
 {
 	u32 i;
 
-	for (i = irq_base; i < irq_base + NUM_EMMA2RH_IRQ_GPIO; i++) {
-		irq_desc[i].status = IRQ_DISABLED;
-		irq_desc[i].action = NULL;
-		irq_desc[i].depth = 2;
-		irq_desc[i].chip = &emma2rh_gpio_irq_controller;
-	}
+	for (i = irq_base; i < irq_base + NUM_EMMA2RH_IRQ_GPIO; i++)
+		set_irq_chip(i, &emma2rh_gpio_irq_controller);
 
 	emma2rh_gpio_irq_base = irq_base;
 }
diff --git a/arch/mips/gt64120/ev64120/irq.c b/arch/mips/gt64120/ev64120/irq.c
index ed4d82b..b3e5796 100644
--- a/arch/mips/gt64120/ev64120/irq.c
+++ b/arch/mips/gt64120/ev64120/irq.c
@@ -66,38 +66,21 @@
 
 static void disable_ev64120_irq(unsigned int irq_nr)
 {
-	unsigned long flags;
-
-	local_irq_save(flags);
 	if (irq_nr >= 8) {	// All PCI interrupts are on line 5 or 2
 		clear_c0_status(9 << 10);
 	} else {
 		clear_c0_status(1 << (irq_nr + 8));
 	}
-	local_irq_restore(flags);
 }
 
 static void enable_ev64120_irq(unsigned int irq_nr)
 {
-	unsigned long flags;
-
-	local_irq_save(flags);
 	if (irq_nr >= 8)	// All PCI interrupts are on line 5 or 2
 		set_c0_status(9 << 10);
 	else
 		set_c0_status(1 << (irq_nr + 8));
-	local_irq_restore(flags);
 }
 
-static unsigned int startup_ev64120_irq(unsigned int irq)
-{
-	enable_ev64120_irq(irq);
-	return 0;		/* Never anything pending  */
-}
-
-#define shutdown_ev64120_irq     disable_ev64120_irq
-#define mask_and_ack_ev64120_irq disable_ev64120_irq
-
 static void end_ev64120_irq(unsigned int irq)
 {
 	if (!(irq_desc[irq].status & (IRQ_DISABLED|IRQ_INPROGRESS)))
@@ -106,13 +89,11 @@
 
 static struct irq_chip ev64120_irq_type = {
 	.typename	= "EV64120",
-	.startup	= startup_ev64120_irq,
-	.shutdown	= shutdown_ev64120_irq,
-	.enable		= enable_ev64120_irq,
-	.disable	= disable_ev64120_irq,
-	.ack		= mask_and_ack_ev64120_irq,
+	.ack		= disable_ev64120_irq,
+	.mask		= disable_ev64120_irq,
+	.mask_ack	= disable_ev64120_irq,
+	.unmask		= enable_ev64120_irq,
 	.end		= end_ev64120_irq,
-	.set_affinity	= NULL
 };
 
 void gt64120_irq_setup(void)
@@ -122,8 +103,6 @@
 	 */
 	clear_c0_status(ST0_IM);
 
-	local_irq_disable();
-
 	/*
 	 * Enable timer.  Other interrupts will be enabled as they are
 	 * registered.
@@ -133,16 +112,5 @@
 
 void __init arch_init_irq(void)
 {
-	int i;
-
-	/*  Let's initialize our IRQ descriptors  */
-	for (i = 0; i < NR_IRQS; i++) {
-		irq_desc[i].status = 0;
-		irq_desc[i].chip = &no_irq_chip;
-		irq_desc[i].action = NULL;
-		irq_desc[i].depth = 0;
-		spin_lock_init(&irq_desc[i].lock);
-	}
-
 	gt64120_irq_setup();
 }
diff --git a/arch/mips/jazz/irq.c b/arch/mips/jazz/irq.c
index d5bd6b3..5c4f50c 100644
--- a/arch/mips/jazz/irq.c
+++ b/arch/mips/jazz/irq.c
@@ -28,14 +28,6 @@
 	spin_unlock_irqrestore(&r4030_lock, flags);
 }
 
-static unsigned int startup_r4030_irq(unsigned int irq)
-{
-	enable_r4030_irq(irq);
-	return 0; /* never anything pending */
-}
-
-#define shutdown_r4030_irq	disable_r4030_irq
-
 void disable_r4030_irq(unsigned int irq)
 {
 	unsigned int mask = ~(1 << (irq - JAZZ_PARALLEL_IRQ));
@@ -47,8 +39,6 @@
 	spin_unlock_irqrestore(&r4030_lock, flags);
 }
 
-#define mask_and_ack_r4030_irq disable_r4030_irq
-
 static void end_r4030_irq(unsigned int irq)
 {
 	if (!(irq_desc[irq].status & (IRQ_DISABLED|IRQ_INPROGRESS)))
@@ -57,11 +47,10 @@
 
 static struct irq_chip r4030_irq_type = {
 	.typename = "R4030",
-	.startup = startup_r4030_irq,
-	.shutdown = shutdown_r4030_irq,
-	.enable = enable_r4030_irq,
-	.disable = disable_r4030_irq,
-	.ack = mask_and_ack_r4030_irq,
+	.ack = disable_r4030_irq,
+	.mask = disable_r4030_irq,
+	.mask_ack = disable_r4030_irq,
+	.unmask = enable_r4030_irq,
 	.end = end_r4030_irq,
 };
 
@@ -69,12 +58,8 @@
 {
 	int i;
 
-	for (i = JAZZ_PARALLEL_IRQ; i <= JAZZ_TIMER_IRQ; i++) {
-		irq_desc[i].status     = IRQ_DISABLED;
-		irq_desc[i].action     = 0;
-		irq_desc[i].depth      = 1;
-		irq_desc[i].chip    = &r4030_irq_type;
-	}
+	for (i = JAZZ_PARALLEL_IRQ; i <= JAZZ_TIMER_IRQ; i++)
+		set_irq_chip_and_handler(i, &r4030_irq_type, handle_level_irq);
 
 	r4030_write_reg16(JAZZ_IO_IRQ_ENABLE, 0);
 	r4030_read_reg16(JAZZ_IO_IRQ_SOURCE);		/* clear pending IRQs */
diff --git a/arch/mips/jmr3927/rbhma3100/irq.c b/arch/mips/jmr3927/rbhma3100/irq.c
index de4a238..3da49c5 100644
--- a/arch/mips/jmr3927/rbhma3100/irq.c
+++ b/arch/mips/jmr3927/rbhma3100/irq.c
@@ -90,17 +90,6 @@
 static void jmr3927_irq_disable(unsigned int irq_nr);
 static void jmr3927_irq_enable(unsigned int irq_nr);
 
-static DEFINE_SPINLOCK(jmr3927_irq_lock);
-
-static unsigned int jmr3927_irq_startup(unsigned int irq)
-{
-	jmr3927_irq_enable(irq);
-
-	return 0;
-}
-
-#define	jmr3927_irq_shutdown	jmr3927_irq_disable
-
 static void jmr3927_irq_ack(unsigned int irq)
 {
 	if (irq == JMR3927_IRQ_IRC_TMR0)
@@ -118,9 +107,7 @@
 static void jmr3927_irq_disable(unsigned int irq_nr)
 {
 	struct tb_irq_space* sp;
-	unsigned long flags;
 
-	spin_lock_irqsave(&jmr3927_irq_lock, flags);
 	for (sp = tb_irq_spaces; sp; sp = sp->next) {
 		if (sp->start_irqno <= irq_nr &&
 		    irq_nr < sp->start_irqno + sp->nr_irqs) {
@@ -130,15 +117,12 @@
 			break;
 		}
 	}
-	spin_unlock_irqrestore(&jmr3927_irq_lock, flags);
 }
 
 static void jmr3927_irq_enable(unsigned int irq_nr)
 {
 	struct tb_irq_space* sp;
-	unsigned long flags;
 
-	spin_lock_irqsave(&jmr3927_irq_lock, flags);
 	for (sp = tb_irq_spaces; sp; sp = sp->next) {
 		if (sp->start_irqno <= irq_nr &&
 		    irq_nr < sp->start_irqno + sp->nr_irqs) {
@@ -148,7 +132,6 @@
 			break;
 		}
 	}
-	spin_unlock_irqrestore(&jmr3927_irq_lock, flags);
 }
 
 /*
@@ -457,11 +440,10 @@
 
 static struct irq_chip jmr3927_irq_controller = {
 	.typename = "jmr3927_irq",
-	.startup = jmr3927_irq_startup,
-	.shutdown = jmr3927_irq_shutdown,
-	.enable = jmr3927_irq_enable,
-	.disable = jmr3927_irq_disable,
 	.ack = jmr3927_irq_ack,
+	.mask = jmr3927_irq_disable,
+	.mask_ack = jmr3927_irq_ack,
+	.unmask = jmr3927_irq_enable,
 	.end = jmr3927_irq_end,
 };
 
@@ -469,12 +451,8 @@
 {
 	u32 i;
 
-	for (i= irq_base; i< irq_base + JMR3927_NR_IRQ_IRC + JMR3927_NR_IRQ_IOC; i++) {
-		irq_desc[i].status = IRQ_DISABLED;
-		irq_desc[i].action = NULL;
-		irq_desc[i].depth = 1;
-		irq_desc[i].chip = &jmr3927_irq_controller;
-	}
+	for (i= irq_base; i< irq_base + JMR3927_NR_IRQ_IRC + JMR3927_NR_IRQ_IOC; i++)
+		set_irq_chip(i, &jmr3927_irq_controller);
 
 	jmr3927_irq_base = irq_base;
 }
diff --git a/arch/mips/jmr3927/rbhma3100/setup.c b/arch/mips/jmr3927/rbhma3100/setup.c
index 16e5dfe..138f25e 100644
--- a/arch/mips/jmr3927/rbhma3100/setup.c
+++ b/arch/mips/jmr3927/rbhma3100/setup.c
@@ -170,7 +170,7 @@
 	while (1);
 }
 
-static unsigned int jmr3927_hpt_read(void)
+static cycle_t jmr3927_hpt_read(void)
 {
 	/* We assume this function is called xtime_lock held. */
 	return jiffies * (JMR3927_TIMER_CLK / HZ) + jmr3927_tmrptr->trr;
@@ -182,7 +182,7 @@
 #endif
 static void __init jmr3927_time_init(void)
 {
-	mips_hpt_read = jmr3927_hpt_read;
+	clocksource_mips.read = jmr3927_hpt_read;
 	mips_hpt_frequency = JMR3927_TIMER_CLK;
 #ifdef USE_RTC_DS1742
 	if (jmr3927_have_nvram()) {
diff --git a/arch/mips/kernel/Makefile b/arch/mips/kernel/Makefile
index 6bfbbed..bbbb8d7 100644
--- a/arch/mips/kernel/Makefile
+++ b/arch/mips/kernel/Makefile
@@ -45,7 +45,6 @@
 obj-$(CONFIG_MIPS_VPE_LOADER)	+= vpe.o
 obj-$(CONFIG_MIPS_VPE_APSP_API)	+= rtlx.o
 
-obj-$(CONFIG_NO_ISA)		+= dma-no-isa.o
 obj-$(CONFIG_I8259)		+= i8259.o
 obj-$(CONFIG_IRQ_CPU)		+= irq_cpu.o
 obj-$(CONFIG_IRQ_CPU_RM7K)	+= irq-rm7000.o
@@ -67,6 +66,8 @@
 
 obj-$(CONFIG_I8253)		+= i8253.o
 
+obj-$(CONFIG_KEXEC)		+= machine_kexec.o relocate_kernel.o
+
 CFLAGS_cpu-bugs64.o	= $(shell if $(CC) $(CFLAGS) -Wa,-mdaddi -c -o /dev/null -xc /dev/null >/dev/null 2>&1; then echo "-DHAVE_AS_SET_DADDI"; fi)
 
 EXTRA_AFLAGS := $(CFLAGS)
diff --git a/arch/mips/kernel/cpu-probe.c b/arch/mips/kernel/cpu-probe.c
index 8485af3..442839e 100644
--- a/arch/mips/kernel/cpu-probe.c
+++ b/arch/mips/kernel/cpu-probe.c
@@ -110,9 +110,8 @@
 {
 	struct cpuinfo_mips *c = &current_cpu_data;
 
-	printk("Checking for 'wait' instruction... ");
 	if (nowait) {
-		printk (" disabled.\n");
+		printk("Wait instruction disabled.\n");
 		return;
 	}
 
@@ -120,11 +119,9 @@
 	case CPU_R3081:
 	case CPU_R3081E:
 		cpu_wait = r3081_wait;
-		printk(" available.\n");
 		break;
 	case CPU_TX3927:
 		cpu_wait = r39xx_wait;
-		printk(" available.\n");
 		break;
 	case CPU_R4200:
 /*	case CPU_R4300: */
@@ -146,33 +143,23 @@
 	case CPU_74K:
  	case CPU_PR4450:
 		cpu_wait = r4k_wait;
-		printk(" available.\n");
 		break;
 	case CPU_TX49XX:
 		cpu_wait = r4k_wait_irqoff;
-		printk(" available.\n");
 		break;
 	case CPU_AU1000:
 	case CPU_AU1100:
 	case CPU_AU1500:
 	case CPU_AU1550:
 	case CPU_AU1200:
-		if (allow_au1k_wait) {
+		if (allow_au1k_wait)
 			cpu_wait = au1k_wait;
-			printk(" available.\n");
-		} else
-			printk(" unavailable.\n");
 		break;
 	case CPU_RM9000:
-		if ((c->processor_id & 0x00ff) >= 0x40) {
+		if ((c->processor_id & 0x00ff) >= 0x40)
 			cpu_wait = r4k_wait;
-			printk(" available.\n");
-		} else {
-			printk(" unavailable.\n");
-		}
 		break;
 	default:
-		printk(" unavailable.\n");
 		break;
 	}
 }
diff --git a/arch/mips/kernel/dma-no-isa.c b/arch/mips/kernel/dma-no-isa.c
deleted file mode 100644
index 6df8b07..0000000
--- a/arch/mips/kernel/dma-no-isa.c
+++ /dev/null
@@ -1,28 +0,0 @@
-/*
- * This file is subject to the terms and conditions of the GNU General Public
- * License.  See the file "COPYING" in the main directory of this archive
- * for more details.
- *
- * Copyright (C) 2004 by Ralf Baechle
- *
- * Dummy ISA DMA functions for systems that don't have ISA but share drivers
- * with ISA such as legacy free PCI.
- */
-#include <linux/errno.h>
-#include <linux/module.h>
-#include <linux/spinlock.h>
-
-DEFINE_SPINLOCK(dma_spin_lock);
-
-int request_dma(unsigned int dmanr, const char * device_id)
-{
-	return -EINVAL;
-}
-
-void free_dma(unsigned int dmanr)
-{
-}
-
-EXPORT_SYMBOL(dma_spin_lock);
-EXPORT_SYMBOL(request_dma);
-EXPORT_SYMBOL(free_dma);
diff --git a/arch/mips/kernel/genex.S b/arch/mips/kernel/genex.S
index 5baca16..aacd4a0 100644
--- a/arch/mips/kernel/genex.S
+++ b/arch/mips/kernel/genex.S
@@ -19,6 +19,7 @@
 #include <asm/mipsregs.h>
 #include <asm/stackframe.h>
 #include <asm/war.h>
+#include <asm/page.h>
 
 #define PANIC_PIC(msg)					\
 		.set push;				\
@@ -378,6 +379,68 @@
 	BUILD_HANDLER dsp dsp sti silent		/* #26 */
 	BUILD_HANDLER reserved reserved sti verbose	/* others */
 
+	.align	5
+	LEAF(handle_ri_rdhwr_vivt)
+#ifdef CONFIG_MIPS_MT_SMTC
+	PANIC_PIC("handle_ri_rdhwr_vivt called")
+#else
+	.set	push
+	.set	noat
+	.set	noreorder
+	/* check if TLB contains a entry for EPC */
+	MFC0	k1, CP0_ENTRYHI
+	andi	k1, 0xff	/* ASID_MASK */
+	MFC0	k0, CP0_EPC
+	PTR_SRL	k0, PAGE_SHIFT + 1
+	PTR_SLL	k0, PAGE_SHIFT + 1
+	or	k1, k0
+	MTC0	k1, CP0_ENTRYHI
+	mtc0_tlbw_hazard
+	tlbp
+	tlb_probe_hazard
+	mfc0	k1, CP0_INDEX
+	.set	pop
+	bltz	k1, handle_ri	/* slow path */
+	/* fall thru */
+#endif
+	END(handle_ri_rdhwr_vivt)
+
+	LEAF(handle_ri_rdhwr)
+	.set	push
+	.set	noat
+	.set	noreorder
+	/* 0x7c03e83b: rdhwr v1,$29 */
+	MFC0	k1, CP0_EPC
+	lui	k0, 0x7c03
+	lw	k1, (k1)
+	ori	k0, 0xe83b
+	.set	reorder
+	bne	k0, k1, handle_ri	/* if not ours */
+	/* The insn is rdhwr.  No need to check CAUSE.BD here. */
+	get_saved_sp	/* k1 := current_thread_info */
+	.set	noreorder
+	MFC0	k0, CP0_EPC
+#if defined(CONFIG_CPU_R3000) || defined(CONFIG_CPU_TX39XX)
+	ori	k1, _THREAD_MASK
+	xori	k1, _THREAD_MASK
+	LONG_L	v1, TI_TP_VALUE(k1)
+	LONG_ADDIU	k0, 4
+	jr	k0
+	 rfe
+#else
+	LONG_ADDIU	k0, 4		/* stall on $k0 */
+	MTC0	k0, CP0_EPC
+	/* I hope three instructions between MTC0 and ERET are enough... */
+	ori	k1, _THREAD_MASK
+	xori	k1, _THREAD_MASK
+	LONG_L	v1, TI_TP_VALUE(k1)
+	.set	mips3
+	eret
+	.set	mips0
+#endif
+	.set	pop
+	END(handle_ri_rdhwr)
+
 #ifdef CONFIG_64BIT
 /* A temporary overflow handler used by check_daddi(). */
 
diff --git a/arch/mips/kernel/head.S b/arch/mips/kernel/head.S
index ddc1b71..a2e095a 100644
--- a/arch/mips/kernel/head.S
+++ b/arch/mips/kernel/head.S
@@ -250,6 +250,9 @@
 	 */
 	page	swapper_pg_dir, _PGD_ORDER
 #ifdef CONFIG_64BIT
+#if defined(CONFIG_MODULES) && !defined(CONFIG_BUILD_ELF64)
+	page	module_pg_dir, _PGD_ORDER
+#endif
 	page	invalid_pmd_table, _PMD_ORDER
 #endif
 	page	invalid_pte_table, _PTE_ORDER
diff --git a/arch/mips/kernel/i8259.c b/arch/mips/kernel/i8259.c
index 48e3418..2526c0c 100644
--- a/arch/mips/kernel/i8259.c
+++ b/arch/mips/kernel/i8259.c
@@ -40,21 +40,10 @@
 		enable_8259A_irq(irq);
 }
 
-#define shutdown_8259A_irq	disable_8259A_irq
-
 void mask_and_ack_8259A(unsigned int);
 
-static unsigned int startup_8259A_irq(unsigned int irq)
-{
-	enable_8259A_irq(irq);
-
-	return 0; /* never anything pending */
-}
-
 static struct irq_chip i8259A_irq_type = {
 	.typename = "XT-PIC",
-	.startup = startup_8259A_irq,
-	.shutdown = shutdown_8259A_irq,
 	.enable = enable_8259A_irq,
 	.disable = disable_8259A_irq,
 	.ack = mask_and_ack_8259A,
@@ -120,7 +109,7 @@
 void make_8259A_irq(unsigned int irq)
 {
 	disable_irq_nosync(irq);
-	irq_desc[irq].chip = &i8259A_irq_type;
+	set_irq_chip(irq, &i8259A_irq_type);
 	enable_irq(irq);
 }
 
@@ -323,12 +312,8 @@
 
 	init_8259A(0);
 
-	for (i = 0; i < 16; i++) {
-		irq_desc[i].status = IRQ_DISABLED;
-		irq_desc[i].action = NULL;
-		irq_desc[i].depth = 1;
-		irq_desc[i].chip = &i8259A_irq_type;
-	}
+	for (i = 0; i < 16; i++)
+		set_irq_chip(i, &i8259A_irq_type);
 
 	setup_irq(2, &irq2);
 }
diff --git a/arch/mips/kernel/irq-msc01.c b/arch/mips/kernel/irq-msc01.c
index 650a80c..bcaad66 100644
--- a/arch/mips/kernel/irq-msc01.c
+++ b/arch/mips/kernel/irq-msc01.c
@@ -45,31 +45,6 @@
 }
 
 /*
- * Enables the IRQ on SOC-it
- */
-static void enable_msc_irq(unsigned int irq)
-{
-	unmask_msc_irq(irq);
-}
-
-/*
- * Initialize the IRQ on SOC-it
- */
-static unsigned int startup_msc_irq(unsigned int irq)
-{
-	unmask_msc_irq(irq);
-	return 0;
-}
-
-/*
- * Disables the IRQ on SOC-it
- */
-static void disable_msc_irq(unsigned int irq)
-{
-	mask_msc_irq(irq);
-}
-
-/*
  * Masks and ACKs an IRQ
  */
 static void level_mask_and_ack_msc_irq(unsigned int irq)
@@ -136,25 +111,23 @@
 		    (irq<<MSC01_IC_RAMW_ADDR_SHF) | (set<<MSC01_IC_RAMW_DATA_SHF));
 }
 
-#define shutdown_msc_irq	disable_msc_irq
-
 struct irq_chip msc_levelirq_type = {
 	.typename = "SOC-it-Level",
-	.startup = startup_msc_irq,
-	.shutdown = shutdown_msc_irq,
-	.enable = enable_msc_irq,
-	.disable = disable_msc_irq,
 	.ack = level_mask_and_ack_msc_irq,
+	.mask = mask_msc_irq,
+	.mask_ack = level_mask_and_ack_msc_irq,
+	.unmask = unmask_msc_irq,
+	.eoi = unmask_msc_irq,
 	.end = end_msc_irq,
 };
 
 struct irq_chip msc_edgeirq_type = {
 	.typename = "SOC-it-Edge",
-	.startup =startup_msc_irq,
-	.shutdown = shutdown_msc_irq,
-	.enable = enable_msc_irq,
-	.disable = disable_msc_irq,
 	.ack = edge_mask_and_ack_msc_irq,
+	.mask = mask_msc_irq,
+	.mask_ack = edge_mask_and_ack_msc_irq,
+	.unmask = unmask_msc_irq,
+	.eoi = unmask_msc_irq,
 	.end = end_msc_irq,
 };
 
@@ -175,14 +148,14 @@
 
 		switch (imp->im_type) {
 		case MSC01_IRQ_EDGE:
-			irq_desc[base+n].chip = &msc_edgeirq_type;
+			set_irq_chip(base+n, &msc_edgeirq_type);
 			if (cpu_has_veic)
 				MSCIC_WRITE(MSC01_IC_SUP+n*8, MSC01_IC_SUP_EDGE_BIT);
 			else
 				MSCIC_WRITE(MSC01_IC_SUP+n*8, MSC01_IC_SUP_EDGE_BIT | imp->im_lvl);
 			break;
 		case MSC01_IRQ_LEVEL:
-			irq_desc[base+n].chip = &msc_levelirq_type;
+			set_irq_chip(base+n, &msc_levelirq_type);
 			if (cpu_has_veic)
 				MSCIC_WRITE(MSC01_IC_SUP+n*8, 0);
 			else
diff --git a/arch/mips/kernel/irq-mv6434x.c b/arch/mips/kernel/irq-mv6434x.c
index 37d1062..6cfb31c 100644
--- a/arch/mips/kernel/irq-mv6434x.c
+++ b/arch/mips/kernel/irq-mv6434x.c
@@ -67,39 +67,6 @@
 }
 
 /*
- * Enables the IRQ on Marvell Chip
- */
-static void enable_mv64340_irq(unsigned int irq)
-{
-	unmask_mv64340_irq(irq);
-}
-
-/*
- * Initialize the IRQ on Marvell Chip
- */
-static unsigned int startup_mv64340_irq(unsigned int irq)
-{
-	unmask_mv64340_irq(irq);
-	return 0;
-}
-
-/*
- * Disables the IRQ on Marvell Chip
- */
-static void disable_mv64340_irq(unsigned int irq)
-{
-	mask_mv64340_irq(irq);
-}
-
-/*
- * Masks and ACKs an IRQ
- */
-static void mask_and_ack_mv64340_irq(unsigned int irq)
-{
-	mask_mv64340_irq(irq);
-}
-
-/*
  * End IRQ processing
  */
 static void end_mv64340_irq(unsigned int irq)
@@ -133,15 +100,12 @@
 		do_IRQ(ls1bit32(irq_src_high) + irq_base + 32);
 }
 
-#define shutdown_mv64340_irq	disable_mv64340_irq
-
 struct irq_chip mv64340_irq_type = {
 	.typename = "MV-64340",
-	.startup = startup_mv64340_irq,
-	.shutdown = shutdown_mv64340_irq,
-	.enable = enable_mv64340_irq,
-	.disable = disable_mv64340_irq,
-	.ack = mask_and_ack_mv64340_irq,
+	.ack = mask_mv64340_irq,
+	.mask = mask_mv64340_irq,
+	.mask_ack = mask_mv64340_irq,
+	.unmask = unmask_mv64340_irq,
 	.end = end_mv64340_irq,
 };
 
@@ -149,13 +113,9 @@
 {
 	int i;
 
-	/* Reset irq handlers pointers to NULL */
-	for (i = base; i < base + 64; i++) {
-		irq_desc[i].status = IRQ_DISABLED;
-		irq_desc[i].action = 0;
-		irq_desc[i].depth = 2;
-		irq_desc[i].chip = &mv64340_irq_type;
-	}
+	for (i = base; i < base + 64; i++)
+		set_irq_chip_and_handler(i, &mv64340_irq_type,
+					 handle_level_irq);
 
 	irq_base = base;
 }
diff --git a/arch/mips/kernel/irq-rm7000.c b/arch/mips/kernel/irq-rm7000.c
index 6b54c71..ddcc2a5 100644
--- a/arch/mips/kernel/irq-rm7000.c
+++ b/arch/mips/kernel/irq-rm7000.c
@@ -29,42 +29,6 @@
 	clear_c0_intcontrol(0x100 << (irq - irq_base));
 }
 
-static inline void rm7k_cpu_irq_enable(unsigned int irq)
-{
-	unsigned long flags;
-
-	local_irq_save(flags);
-	unmask_rm7k_irq(irq);
-	local_irq_restore(flags);
-}
-
-static void rm7k_cpu_irq_disable(unsigned int irq)
-{
-	unsigned long flags;
-
-	local_irq_save(flags);
-	mask_rm7k_irq(irq);
-	local_irq_restore(flags);
-}
-
-static unsigned int rm7k_cpu_irq_startup(unsigned int irq)
-{
-	rm7k_cpu_irq_enable(irq);
-
-	return 0;
-}
-
-#define	rm7k_cpu_irq_shutdown	rm7k_cpu_irq_disable
-
-/*
- * While we ack the interrupt interrupts are disabled and thus we don't need
- * to deal with concurrency issues.  Same for rm7k_cpu_irq_end.
- */
-static void rm7k_cpu_irq_ack(unsigned int irq)
-{
-	mask_rm7k_irq(irq);
-}
-
 static void rm7k_cpu_irq_end(unsigned int irq)
 {
 	if (!(irq_desc[irq].status & (IRQ_DISABLED | IRQ_INPROGRESS)))
@@ -73,11 +37,10 @@
 
 static struct irq_chip rm7k_irq_controller = {
 	.typename = "RM7000",
-	.startup = rm7k_cpu_irq_startup,
-	.shutdown = rm7k_cpu_irq_shutdown,
-	.enable = rm7k_cpu_irq_enable,
-	.disable = rm7k_cpu_irq_disable,
-	.ack = rm7k_cpu_irq_ack,
+	.ack = mask_rm7k_irq,
+	.mask = mask_rm7k_irq,
+	.mask_ack = mask_rm7k_irq,
+	.unmask = unmask_rm7k_irq,
 	.end = rm7k_cpu_irq_end,
 };
 
@@ -87,12 +50,9 @@
 
 	clear_c0_intcontrol(0x00000f00);		/* Mask all */
 
-	for (i = base; i < base + 4; i++) {
-		irq_desc[i].status = IRQ_DISABLED;
-		irq_desc[i].action = NULL;
-		irq_desc[i].depth = 1;
-		irq_desc[i].chip = &rm7k_irq_controller;
-	}
+	for (i = base; i < base + 4; i++)
+		set_irq_chip_and_handler(i, &rm7k_irq_controller,
+					 handle_level_irq);
 
 	irq_base = base;
 }
diff --git a/arch/mips/kernel/irq-rm9000.c b/arch/mips/kernel/irq-rm9000.c
index 62f011b..ba6440c 100644
--- a/arch/mips/kernel/irq-rm9000.c
+++ b/arch/mips/kernel/irq-rm9000.c
@@ -48,15 +48,6 @@
 	local_irq_restore(flags);
 }
 
-static unsigned int rm9k_cpu_irq_startup(unsigned int irq)
-{
-	rm9k_cpu_irq_enable(irq);
-
-	return 0;
-}
-
-#define	rm9k_cpu_irq_shutdown	rm9k_cpu_irq_disable
-
 /*
  * Performance counter interrupts are global on all processors.
  */
@@ -89,16 +80,6 @@
 	on_each_cpu(local_rm9k_perfcounter_irq_shutdown, (void *) irq, 0, 1);
 }
 
-
-/*
- * While we ack the interrupt interrupts are disabled and thus we don't need
- * to deal with concurrency issues.  Same for rm9k_cpu_irq_end.
- */
-static void rm9k_cpu_irq_ack(unsigned int irq)
-{
-	mask_rm9k_irq(irq);
-}
-
 static void rm9k_cpu_irq_end(unsigned int irq)
 {
 	if (!(irq_desc[irq].status & (IRQ_DISABLED | IRQ_INPROGRESS)))
@@ -107,11 +88,10 @@
 
 static struct irq_chip rm9k_irq_controller = {
 	.typename = "RM9000",
-	.startup = rm9k_cpu_irq_startup,
-	.shutdown = rm9k_cpu_irq_shutdown,
-	.enable = rm9k_cpu_irq_enable,
-	.disable = rm9k_cpu_irq_disable,
-	.ack = rm9k_cpu_irq_ack,
+	.ack = mask_rm9k_irq,
+	.mask = mask_rm9k_irq,
+	.mask_ack = mask_rm9k_irq,
+	.unmask = unmask_rm9k_irq,
 	.end = rm9k_cpu_irq_end,
 };
 
@@ -119,9 +99,10 @@
 	.typename = "RM9000",
 	.startup = rm9k_perfcounter_irq_startup,
 	.shutdown = rm9k_perfcounter_irq_shutdown,
-	.enable = rm9k_cpu_irq_enable,
-	.disable = rm9k_cpu_irq_disable,
-	.ack = rm9k_cpu_irq_ack,
+	.ack = mask_rm9k_irq,
+	.mask = mask_rm9k_irq,
+	.mask_ack = mask_rm9k_irq,
+	.unmask = unmask_rm9k_irq,
 	.end = rm9k_cpu_irq_end,
 };
 
@@ -135,15 +116,13 @@
 
 	clear_c0_intcontrol(0x0000f000);		/* Mask all */
 
-	for (i = base; i < base + 4; i++) {
-		irq_desc[i].status = IRQ_DISABLED;
-		irq_desc[i].action = NULL;
-		irq_desc[i].depth = 1;
-		irq_desc[i].chip = &rm9k_irq_controller;
-	}
+	for (i = base; i < base + 4; i++)
+		set_irq_chip_and_handler(i, &rm9k_irq_controller,
+					 handle_level_irq);
 
 	rm9000_perfcount_irq = base + 1;
-	irq_desc[rm9000_perfcount_irq].chip = &rm9k_perfcounter_irq;
+	set_irq_chip_and_handler(rm9000_perfcount_irq, &rm9k_perfcounter_irq,
+				 handle_level_irq);
 
 	irq_base = base;
 }
diff --git a/arch/mips/kernel/irq.c b/arch/mips/kernel/irq.c
index 9b0e49d..b339798 100644
--- a/arch/mips/kernel/irq.c
+++ b/arch/mips/kernel/irq.c
@@ -88,25 +88,6 @@
 unsigned long irq_hwmask[NR_IRQS];
 #endif /* CONFIG_MIPS_MT_SMTC */
 
-#undef do_IRQ
-
-/*
- * do_IRQ handles all normal device IRQ's (the special
- * SMP cross-CPU interrupts have their own specific
- * handlers).
- */
-asmlinkage unsigned int do_IRQ(unsigned int irq)
-{
-	irq_enter();
-
-	__DO_IRQ_SMTC_HOOK();
-	__do_IRQ(irq);
-
-	irq_exit();
-
-	return 1;
-}
-
 /*
  * Generic, controller-independent functions:
  */
@@ -172,19 +153,6 @@
 
 void __init init_IRQ(void)
 {
-	int i;
-
-	for (i = 0; i < NR_IRQS; i++) {
-		irq_desc[i].status  = IRQ_DISABLED;
-		irq_desc[i].action  = NULL;
-		irq_desc[i].depth   = 1;
-		irq_desc[i].chip = &no_irq_chip;
-		spin_lock_init(&irq_desc[i].lock);
-#ifdef CONFIG_MIPS_MT_SMTC
-		irq_hwmask[i] = 0;
-#endif /* CONFIG_MIPS_MT_SMTC */
-	}
-
 	arch_init_irq();
 
 #ifdef CONFIG_KGDB
diff --git a/arch/mips/kernel/irq_cpu.c b/arch/mips/kernel/irq_cpu.c
index 9bb21c7..be5ac23 100644
--- a/arch/mips/kernel/irq_cpu.c
+++ b/arch/mips/kernel/irq_cpu.c
@@ -50,44 +50,6 @@
 	irq_disable_hazard();
 }
 
-static inline void mips_cpu_irq_enable(unsigned int irq)
-{
-	unsigned long flags;
-
-	local_irq_save(flags);
-	unmask_mips_irq(irq);
-	back_to_back_c0_hazard();
-	local_irq_restore(flags);
-}
-
-static void mips_cpu_irq_disable(unsigned int irq)
-{
-	unsigned long flags;
-
-	local_irq_save(flags);
-	mask_mips_irq(irq);
-	back_to_back_c0_hazard();
-	local_irq_restore(flags);
-}
-
-static unsigned int mips_cpu_irq_startup(unsigned int irq)
-{
-	mips_cpu_irq_enable(irq);
-
-	return 0;
-}
-
-#define	mips_cpu_irq_shutdown		mips_cpu_irq_disable
-
-/*
- * While we ack the interrupt interrupts are disabled and thus we don't need
- * to deal with concurrency issues.  Same for mips_cpu_irq_end.
- */
-static void mips_cpu_irq_ack(unsigned int irq)
-{
-	mask_mips_irq(irq);
-}
-
 static void mips_cpu_irq_end(unsigned int irq)
 {
 	if (!(irq_desc[irq].status & (IRQ_DISABLED | IRQ_INPROGRESS)))
@@ -96,11 +58,11 @@
 
 static struct irq_chip mips_cpu_irq_controller = {
 	.typename	= "MIPS",
-	.startup	= mips_cpu_irq_startup,
-	.shutdown	= mips_cpu_irq_shutdown,
-	.enable		= mips_cpu_irq_enable,
-	.disable	= mips_cpu_irq_disable,
-	.ack		= mips_cpu_irq_ack,
+	.ack		= mask_mips_irq,
+	.mask		= mask_mips_irq,
+	.mask_ack	= mask_mips_irq,
+	.unmask		= unmask_mips_irq,
+	.eoi		= unmask_mips_irq,
 	.end		= mips_cpu_irq_end,
 };
 
@@ -110,8 +72,6 @@
 
 #define unmask_mips_mt_irq	unmask_mips_irq
 #define mask_mips_mt_irq	mask_mips_irq
-#define mips_mt_cpu_irq_enable	mips_cpu_irq_enable
-#define mips_mt_cpu_irq_disable	mips_cpu_irq_disable
 
 static unsigned int mips_mt_cpu_irq_startup(unsigned int irq)
 {
@@ -119,13 +79,11 @@
 
 	clear_c0_cause(0x100 << (irq - mips_cpu_irq_base));
 	evpe(vpflags);
-	mips_mt_cpu_irq_enable(irq);
+	unmask_mips_mt_irq(irq);
 
 	return 0;
 }
 
-#define	mips_mt_cpu_irq_shutdown	mips_mt_cpu_irq_disable
-
 /*
  * While we ack the interrupt interrupts are disabled and thus we don't need
  * to deal with concurrency issues.  Same for mips_cpu_irq_end.
@@ -143,10 +101,11 @@
 static struct irq_chip mips_mt_cpu_irq_controller = {
 	.typename	= "MIPS",
 	.startup	= mips_mt_cpu_irq_startup,
-	.shutdown	= mips_mt_cpu_irq_shutdown,
-	.enable		= mips_mt_cpu_irq_enable,
-	.disable	= mips_mt_cpu_irq_disable,
 	.ack		= mips_mt_cpu_irq_ack,
+	.mask		= mask_mips_mt_irq,
+	.mask_ack	= mips_mt_cpu_irq_ack,
+	.unmask		= unmask_mips_mt_irq,
+	.eoi		= unmask_mips_mt_irq,
 	.end		= mips_mt_cpu_irq_end,
 };
 
@@ -163,19 +122,12 @@
 	 * leave them uninitialized for other processors.
 	 */
 	if (cpu_has_mipsmt)
-		for (i = irq_base; i < irq_base + 2; i++) {
-			irq_desc[i].status = IRQ_DISABLED;
-			irq_desc[i].action = NULL;
-			irq_desc[i].depth = 1;
-			irq_desc[i].chip = &mips_mt_cpu_irq_controller;
-		}
+		for (i = irq_base; i < irq_base + 2; i++)
+			set_irq_chip(i, &mips_mt_cpu_irq_controller);
 
-	for (i = irq_base + 2; i < irq_base + 8; i++) {
-		irq_desc[i].status = IRQ_DISABLED;
-		irq_desc[i].action = NULL;
-		irq_desc[i].depth = 1;
-		irq_desc[i].chip = &mips_cpu_irq_controller;
-	}
+	for (i = irq_base + 2; i < irq_base + 8; i++)
+		set_irq_chip_and_handler(i, &mips_cpu_irq_controller,
+					 handle_level_irq);
 
 	mips_cpu_irq_base = irq_base;
 }
diff --git a/arch/mips/kernel/machine_kexec.c b/arch/mips/kernel/machine_kexec.c
new file mode 100644
index 0000000..e0ad754
--- /dev/null
+++ b/arch/mips/kernel/machine_kexec.c
@@ -0,0 +1,85 @@
+/*
+ * machine_kexec.c for kexec
+ * Created by <nschichan@corp.free.fr> on Thu Oct 12 15:15:06 2006
+ *
+ * This source code is licensed under the GNU General Public License,
+ * Version 2.  See the file COPYING for more details.
+ */
+
+#include <linux/kexec.h>
+#include <linux/mm.h>
+#include <linux/delay.h>
+
+#include <asm/cacheflush.h>
+#include <asm/page.h>
+
+const extern unsigned char relocate_new_kernel[];
+const extern unsigned int relocate_new_kernel_size;
+
+extern unsigned long kexec_start_address;
+extern unsigned long kexec_indirection_page;
+
+int
+machine_kexec_prepare(struct kimage *kimage)
+{
+	return 0;
+}
+
+void
+machine_kexec_cleanup(struct kimage *kimage)
+{
+}
+
+void
+machine_shutdown(void)
+{
+}
+
+void
+machine_crash_shutdown(struct pt_regs *regs)
+{
+}
+
+void
+machine_kexec(struct kimage *image)
+{
+	unsigned long reboot_code_buffer;
+	unsigned long entry;
+	unsigned long *ptr;
+
+	reboot_code_buffer =
+	  (unsigned long)page_address(image->control_code_page);
+
+	kexec_start_address = image->start;
+	kexec_indirection_page = phys_to_virt(image->head & PAGE_MASK);
+
+	memcpy((void*)reboot_code_buffer, relocate_new_kernel,
+	       relocate_new_kernel_size);
+
+	/*
+	 * The generic kexec code builds a page list with physical
+	 * addresses. they are directly accessible through KSEG0 (or
+	 * CKSEG0 or XPHYS if on 64bit system), hence the
+	 * pys_to_virt() call.
+	 */
+	for (ptr = &image->head; (entry = *ptr) && !(entry &IND_DONE);
+	     ptr = (entry & IND_INDIRECTION) ?
+	       phys_to_virt(entry & PAGE_MASK) : ptr + 1) {
+		if (*ptr & IND_SOURCE || *ptr & IND_INDIRECTION ||
+		    *ptr & IND_DESTINATION)
+			*ptr = phys_to_virt(*ptr);
+	}
+
+	/*
+	 * we do not want to be bothered.
+	 */
+	local_irq_disable();
+
+	flush_icache_range(reboot_code_buffer,
+			   reboot_code_buffer + KEXEC_CONTROL_CODE_SIZE);
+
+	printk("Will call new kernel at %08x\n", image->start);
+	printk("Bye ...\n");
+	flush_cache_all();
+	((void (*)(void))reboot_code_buffer)();
+}
diff --git a/arch/mips/kernel/module.c b/arch/mips/kernel/module.c
index d7bf021..cb08014 100644
--- a/arch/mips/kernel/module.c
+++ b/arch/mips/kernel/module.c
@@ -29,6 +29,7 @@
 #include <linux/kernel.h>
 #include <linux/module.h>
 #include <linux/spinlock.h>
+#include <asm/pgtable.h>	/* MODULE_START */
 
 struct mips_hi16 {
 	struct mips_hi16 *next;
@@ -43,9 +44,23 @@
 
 void *module_alloc(unsigned long size)
 {
+#ifdef MODULE_START
+	struct vm_struct *area;
+
+	size = PAGE_ALIGN(size);
+	if (!size)
+		return NULL;
+
+	area = __get_vm_area(size, VM_ALLOC, MODULE_START, MODULE_END);
+	if (!area)
+		return NULL;
+
+	return __vmalloc_area(area, GFP_KERNEL, PAGE_KERNEL);
+#else
 	if (size == 0)
 		return NULL;
 	return vmalloc(size);
+#endif
 }
 
 /* Free memory returned from module_alloc */
diff --git a/arch/mips/kernel/relocate_kernel.S b/arch/mips/kernel/relocate_kernel.S
new file mode 100644
index 0000000..a3f0d00
--- /dev/null
+++ b/arch/mips/kernel/relocate_kernel.S
@@ -0,0 +1,80 @@
+/*
+ * relocate_kernel.S for kexec
+ * Created by <nschichan@corp.free.fr> on Thu Oct 12 17:49:57 2006
+ *
+ * This source code is licensed under the GNU General Public License,
+ * Version 2.  See the file COPYING for more details.
+ */
+
+#include <asm/asm.h>
+#include <asm/asmmacro.h>
+#include <asm/regdef.h>
+#include <asm/page.h>
+#include <asm/mipsregs.h>
+#include <asm/stackframe.h>
+#include <asm/addrspace.h>
+
+	.globl relocate_new_kernel
+relocate_new_kernel:
+
+	PTR_L	s0, kexec_indirection_page
+	PTR_L	s1, kexec_start_address
+
+process_entry:
+	PTR_L	s2, (s0)
+	PTR_ADD	s0, s0, SZREG
+
+	/* destination page */
+	and	s3, s2, 0x1
+	beq	s3, zero, 1f
+	and	s4, s2, ~0x1	/* store destination addr in s4 */
+	move	a0, s4
+	b	process_entry
+
+1:
+	/* indirection page, update s0  */
+	and	s3, s2, 0x2
+	beq	s3, zero, 1f
+	and	s0, s2, ~0x2
+	b	process_entry
+
+1:
+	/* done page */
+	and	s3, s2, 0x4
+	beq	s3, zero, 1f
+	b	done
+1:
+	/* source page */
+	and	s3, s2, 0x8
+	beq	s3, zero, process_entry
+	and	s2, s2, ~0x8
+	li	s6, (1 << PAGE_SHIFT) / SZREG
+
+copy_word:
+	/* copy page word by word */
+	REG_L	s5, (s2)
+	REG_S	s5, (s4)
+	INT_ADD	s4, s4, SZREG
+	INT_ADD	s2, s2, SZREG
+	INT_SUB	s6, s6, 1
+	beq	s6, zero, process_entry
+	b	copy_word
+	b	process_entry
+
+done:
+	/* jump to kexec_start_address */
+	j	s1
+
+	.globl kexec_start_address
+kexec_start_address:
+	.long	0x0
+
+	.globl kexec_indirection_page
+kexec_indirection_page:
+	.long	0x0
+
+relocate_new_kernel_end:
+
+	.globl relocate_new_kernel_size
+relocate_new_kernel_size:
+	.long relocate_new_kernel_end - relocate_new_kernel
diff --git a/arch/mips/kernel/scall32-o32.S b/arch/mips/kernel/scall32-o32.S
index a95f37d..7c0b393 100644
--- a/arch/mips/kernel/scall32-o32.S
+++ b/arch/mips/kernel/scall32-o32.S
@@ -653,7 +653,7 @@
 	sys	sys_move_pages		6
 	sys	sys_set_robust_list	2
 	sys	sys_get_robust_list	3	/* 4310 */
-	sys	sys_ni_syscall		0
+	sys	sys_kexec_load		4
 	sys	sys_getcpu		3
 	sys	sys_epoll_pwait		6
 	.endm
diff --git a/arch/mips/kernel/scall64-64.S b/arch/mips/kernel/scall64-64.S
index 8fb0f60..e569b84 100644
--- a/arch/mips/kernel/scall64-64.S
+++ b/arch/mips/kernel/scall64-64.S
@@ -468,6 +468,6 @@
 	PTR	sys_move_pages
 	PTR	sys_set_robust_list
 	PTR	sys_get_robust_list
-	PTR	sys_ni_syscall			/* 5270 */
+	PTR	sys_kexec_load			/* 5270 */
 	PTR	sys_getcpu
 	PTR	sys_epoll_pwait
diff --git a/arch/mips/kernel/scall64-n32.S b/arch/mips/kernel/scall64-n32.S
index 0da5ca2..5b18f26 100644
--- a/arch/mips/kernel/scall64-n32.S
+++ b/arch/mips/kernel/scall64-n32.S
@@ -394,6 +394,6 @@
 	PTR	sys_move_pages
 	PTR	compat_sys_set_robust_list
 	PTR	compat_sys_get_robust_list
-	PTR	sys_ni_syscall
+	PTR	compat_sys_kexec_load
 	PTR	sys_getcpu
 	PTR	sys_epoll_pwait
diff --git a/arch/mips/kernel/scall64-o32.S b/arch/mips/kernel/scall64-o32.S
index b9d00ca..e91379c 100644
--- a/arch/mips/kernel/scall64-o32.S
+++ b/arch/mips/kernel/scall64-o32.S
@@ -516,7 +516,7 @@
 	PTR	compat_sys_move_pages
 	PTR	compat_sys_set_robust_list
 	PTR	compat_sys_get_robust_list	/* 4310 */
-	PTR	sys_ni_syscall
+	PTR	compat_sys_kexec_load
 	PTR	sys_getcpu
 	PTR	sys_epoll_pwait
 	.size	sys_call_table,.-sys_call_table
diff --git a/arch/mips/kernel/setup.c b/arch/mips/kernel/setup.c
index 8f6e896..89440a0 100644
--- a/arch/mips/kernel/setup.c
+++ b/arch/mips/kernel/setup.c
@@ -145,13 +145,12 @@
 	unsigned long start = memparse(p, &p);
 
 #ifdef CONFIG_64BIT
-	/* HACK: Guess if the sign extension was forgotten */
-	if (start > 0x0000000080000000 && start < 0x00000000ffffffff)
-		start |= 0xffffffff00000000UL;
+	/* Guess if the sign extension was forgotten by bootloader */
+	if (start < XKPHYS)
+		start = (int)start;
 #endif
 	initrd_start = start;
 	initrd_end += start;
-
 	return 0;
 }
 early_param("rd_start", rd_start_early);
@@ -159,41 +158,64 @@
 static int __init rd_size_early(char *p)
 {
 	initrd_end += memparse(p, &p);
-
 	return 0;
 }
 early_param("rd_size", rd_size_early);
 
+/* it returns the next free pfn after initrd */
 static unsigned long __init init_initrd(void)
 {
-	unsigned long tmp, end, size;
+	unsigned long end;
 	u32 *initrd_header;
 
-	ROOT_DEV = Root_RAM0;
-
 	/*
 	 * Board specific code or command line parser should have
 	 * already set up initrd_start and initrd_end. In these cases
 	 * perfom sanity checks and use them if all looks good.
 	 */
-	size = initrd_end - initrd_start;
-	if (initrd_end == 0 || size == 0) {
-		initrd_start = 0;
-		initrd_end = 0;
-	} else
-		return initrd_end;
+	if (initrd_start && initrd_end > initrd_start)
+		goto sanitize;
 
-	end = (unsigned long)&_end;
-	tmp = PAGE_ALIGN(end) - sizeof(u32) * 2;
-	if (tmp < end)
-		tmp += PAGE_SIZE;
+	/*
+	 * See if initrd has been added to the kernel image by
+	 * arch/mips/boot/addinitrd.c. In that case a header is
+	 * prepended to initrd and is made up by 8 bytes. The fisrt
+	 * word is a magic number and the second one is the size of
+	 * initrd.  Initrd start must be page aligned in any cases.
+	 */
+	initrd_header = __va(PAGE_ALIGN(__pa_symbol(&_end) + 8)) - 8;
+	if (initrd_header[0] != 0x494E5244)
+		goto disable;
+	initrd_start = (unsigned long)(initrd_header + 2);
+	initrd_end = initrd_start + initrd_header[1];
 
-	initrd_header = (u32 *)tmp;
-	if (initrd_header[0] == 0x494E5244) {
-		initrd_start = (unsigned long)&initrd_header[2];
-		initrd_end = initrd_start + initrd_header[1];
+sanitize:
+	if (initrd_start & ~PAGE_MASK) {
+		printk(KERN_ERR "initrd start must be page aligned\n");
+		goto disable;
 	}
-	return initrd_end;
+	if (initrd_start < PAGE_OFFSET) {
+		printk(KERN_ERR "initrd start < PAGE_OFFSET\n");
+		goto disable;
+	}
+
+	/*
+	 * Sanitize initrd addresses. For example firmware
+	 * can't guess if they need to pass them through
+	 * 64-bits values if the kernel has been built in pure
+	 * 32-bit. We need also to switch from KSEG0 to XKPHYS
+	 * addresses now, so the code can now safely use __pa().
+	 */
+	end = __pa(initrd_end);
+	initrd_end = (unsigned long)__va(end);
+	initrd_start = (unsigned long)__va(__pa(initrd_start));
+
+	ROOT_DEV = Root_RAM0;
+	return PFN_UP(end);
+disable:
+	initrd_start = 0;
+	initrd_end = 0;
+	return 0;
 }
 
 static void __init finalize_initrd(void)
@@ -204,12 +226,12 @@
 		printk(KERN_INFO "Initrd not found or empty");
 		goto disable;
 	}
-	if (CPHYSADDR(initrd_end) > PFN_PHYS(max_low_pfn)) {
+	if (__pa(initrd_end) > PFN_PHYS(max_low_pfn)) {
 		printk("Initrd extends beyond end of memory");
 		goto disable;
 	}
 
-	reserve_bootmem(CPHYSADDR(initrd_start), size);
+	reserve_bootmem(__pa(initrd_start), size);
 	initrd_below_start_ok = 1;
 
 	printk(KERN_INFO "Initial ramdisk at: 0x%lx (%lu bytes)\n",
@@ -259,8 +281,7 @@
 	 * not selected. Once that done we can determine the low bound
 	 * of usable memory.
 	 */
-	reserved_end = init_initrd();
-	reserved_end = PFN_UP(CPHYSADDR(max(reserved_end, (unsigned long)&_end)));
+	reserved_end = max(init_initrd(), PFN_UP(__pa_symbol(&_end)));
 
 	/*
 	 * Find the highest page frame number we have available.
@@ -432,10 +453,10 @@
 	if (UNCAC_BASE != IO_BASE)
 		return;
 
-	code_resource.start = virt_to_phys(&_text);
-	code_resource.end = virt_to_phys(&_etext) - 1;
-	data_resource.start = virt_to_phys(&_etext);
-	data_resource.end = virt_to_phys(&_edata) - 1;
+	code_resource.start = __pa_symbol(&_text);
+	code_resource.end = __pa_symbol(&_etext) - 1;
+	data_resource.start = __pa_symbol(&_etext);
+	data_resource.end = __pa_symbol(&_edata) - 1;
 
 	/*
 	 * Request address space for all standard RAM.
diff --git a/arch/mips/kernel/signal_n32.c b/arch/mips/kernel/signal_n32.c
index 477c533..a67c185 100644
--- a/arch/mips/kernel/signal_n32.c
+++ b/arch/mips/kernel/signal_n32.c
@@ -17,7 +17,6 @@
  */
 #include <linux/cache.h>
 #include <linux/sched.h>
-#include <linux/sched.h>
 #include <linux/mm.h>
 #include <linux/smp.h>
 #include <linux/smp_lock.h>
diff --git a/arch/mips/kernel/smp-mt.c b/arch/mips/kernel/smp-mt.c
index 2ac19a6..1ee689c 100644
--- a/arch/mips/kernel/smp-mt.c
+++ b/arch/mips/kernel/smp-mt.c
@@ -278,7 +278,9 @@
 
 	/* need to mark IPI's as IRQ_PER_CPU */
 	irq_desc[cpu_ipi_resched_irq].status |= IRQ_PER_CPU;
+	set_irq_handler(cpu_ipi_resched_irq, handle_percpu_irq);
 	irq_desc[cpu_ipi_call_irq].status |= IRQ_PER_CPU;
+	set_irq_handler(cpu_ipi_call_irq, handle_percpu_irq);
 }
 
 /*
diff --git a/arch/mips/kernel/smtc.c b/arch/mips/kernel/smtc.c
index 3b78caf..802febe 100644
--- a/arch/mips/kernel/smtc.c
+++ b/arch/mips/kernel/smtc.c
@@ -1009,6 +1009,7 @@
 	setup_irq_smtc(cpu_ipi_irq, &irq_ipi, (0x100 << MIPS_CPU_IPI_IRQ));
 
 	irq_desc[cpu_ipi_irq].status |= IRQ_PER_CPU;
+	set_irq_handler(cpu_ipi_irq, handle_percpu_irq);
 }
 
 /*
diff --git a/arch/mips/kernel/time.c b/arch/mips/kernel/time.c
index e535f86..11aab6d 100644
--- a/arch/mips/kernel/time.c
+++ b/arch/mips/kernel/time.c
@@ -11,7 +11,6 @@
  * Free Software Foundation;  either version 2 of the  License, or (at your
  * option) any later version.
  */
-#include <linux/clocksource.h>
 #include <linux/types.h>
 #include <linux/kernel.h>
 #include <linux/init.h>
@@ -83,17 +82,11 @@
 /*
  * Null high precision timer functions for systems lacking one.
  */
-static unsigned int null_hpt_read(void)
+static cycle_t null_hpt_read(void)
 {
 	return 0;
 }
 
-static void __init null_hpt_init(void)
-{
-	/* nothing */
-}
-
-
 /*
  * Timer ack for an R4k-compatible timer of a known frequency.
  */
@@ -118,7 +111,7 @@
 /*
  * High precision timer functions for a R4k-compatible timer.
  */
-static unsigned int c0_hpt_read(void)
+static cycle_t c0_hpt_read(void)
 {
 	return read_c0_count();
 }
@@ -132,9 +125,6 @@
 
 int (*mips_timer_state)(void);
 void (*mips_timer_ack)(void);
-unsigned int (*mips_hpt_read)(void);
-void (*mips_hpt_init)(void) __initdata = null_hpt_init;
-unsigned int mips_hpt_mask = 0xffffffff;
 
 /* last time when xtime and rtc are sync'ed up */
 static long last_rtc_update;
@@ -276,8 +266,7 @@
 
 static unsigned int __init calibrate_hpt(void)
 {
-	u64 frequency;
-	u32 hpt_start, hpt_end, hpt_count, hz;
+	cycle_t frequency, hpt_start, hpt_end, hpt_count, hz;
 
 	const int loops = HZ / 10;
 	int log_2_loops = 0;
@@ -303,28 +292,23 @@
 	 * during the calculated number of periods between timer
 	 * interrupts.
 	 */
-	hpt_start = mips_hpt_read();
+	hpt_start = clocksource_mips.read();
 	do {
 		while (mips_timer_state());
 		while (!mips_timer_state());
 	} while (--i);
-	hpt_end = mips_hpt_read();
+	hpt_end = clocksource_mips.read();
 
-	hpt_count = (hpt_end - hpt_start) & mips_hpt_mask;
+	hpt_count = (hpt_end - hpt_start) & clocksource_mips.mask;
 	hz = HZ;
-	frequency = (u64)hpt_count * (u64)hz;
+	frequency = hpt_count * hz;
 
 	return frequency >> log_2_loops;
 }
 
-static cycle_t read_mips_hpt(void)
-{
-	return (cycle_t)mips_hpt_read();
-}
-
-static struct clocksource clocksource_mips = {
+struct clocksource clocksource_mips = {
 	.name		= "MIPS",
-	.read		= read_mips_hpt,
+	.mask		= 0xffffffff,
 	.is_continuous	= 1,
 };
 
@@ -333,7 +317,7 @@
 	u64 temp;
 	u32 shift;
 
-	if (!mips_hpt_frequency || mips_hpt_read == null_hpt_read)
+	if (!mips_hpt_frequency || clocksource_mips.read == null_hpt_read)
 		return;
 
 	/* Calclate a somewhat reasonable rating value */
@@ -347,7 +331,6 @@
 	}
 	clocksource_mips.shift = shift;
 	clocksource_mips.mult = (u32)temp;
-	clocksource_mips.mask = mips_hpt_mask;
 
 	clocksource_register(&clocksource_mips);
 }
@@ -367,32 +350,36 @@
 	                        -xtime.tv_sec, -xtime.tv_nsec);
 
 	/* Choose appropriate high precision timer routines.  */
-	if (!cpu_has_counter && !mips_hpt_read)
+	if (!cpu_has_counter && !clocksource_mips.read)
 		/* No high precision timer -- sorry.  */
-		mips_hpt_read = null_hpt_read;
+		clocksource_mips.read = null_hpt_read;
 	else if (!mips_hpt_frequency && !mips_timer_state) {
 		/* A high precision timer of unknown frequency.  */
-		if (!mips_hpt_read)
+		if (!clocksource_mips.read)
 			/* No external high precision timer -- use R4k.  */
-			mips_hpt_read = c0_hpt_read;
+			clocksource_mips.read = c0_hpt_read;
 	} else {
 		/* We know counter frequency.  Or we can get it.  */
-		if (!mips_hpt_read) {
+		if (!clocksource_mips.read) {
 			/* No external high precision timer -- use R4k.  */
-			mips_hpt_read = c0_hpt_read;
+			clocksource_mips.read = c0_hpt_read;
 
 			if (!mips_timer_state) {
 				/* No external timer interrupt -- use R4k.  */
-				mips_hpt_init = c0_hpt_timer_init;
 				mips_timer_ack = c0_timer_ack;
+				/* Calculate cache parameters.  */
+				cycles_per_jiffy =
+					(mips_hpt_frequency + HZ / 2) / HZ;
+				/*
+				 * This sets up the high precision
+				 * timer for the first interrupt.
+				 */
+				c0_hpt_timer_init();
 			}
 		}
 		if (!mips_hpt_frequency)
 			mips_hpt_frequency = calibrate_hpt();
 
-		/* Calculate cache parameters.  */
-		cycles_per_jiffy = (mips_hpt_frequency + HZ / 2) / HZ;
-
 		/* Report the high precision timer rate for a reference.  */
 		printk("Using %u.%03u MHz high precision timer.\n",
 		       ((mips_hpt_frequency + 500) / 1000) / 1000,
@@ -403,9 +390,6 @@
 		/* No timer interrupt ack (e.g. i8254).  */
 		mips_timer_ack = null_timer_ack;
 
-	/* This sets up the high precision timer for the first interrupt.  */
-	mips_hpt_init();
-
 	/*
 	 * Call board specific timer interrupt setup.
 	 *
diff --git a/arch/mips/kernel/traps.c b/arch/mips/kernel/traps.c
index 9fda1b8..2a932ca 100644
--- a/arch/mips/kernel/traps.c
+++ b/arch/mips/kernel/traps.c
@@ -54,6 +54,8 @@
 extern asmlinkage void handle_sys(void);
 extern asmlinkage void handle_bp(void);
 extern asmlinkage void handle_ri(void);
+extern asmlinkage void handle_ri_rdhwr_vivt(void);
+extern asmlinkage void handle_ri_rdhwr(void);
 extern asmlinkage void handle_cpu(void);
 extern asmlinkage void handle_ov(void);
 extern asmlinkage void handle_tr(void);
@@ -397,19 +399,6 @@
 	force_sig(SIGBUS, current);
 }
 
-static inline int get_insn_opcode(struct pt_regs *regs, unsigned int *opcode)
-{
-	unsigned int __user *epc;
-
-	epc = (unsigned int __user *) regs->cp0_epc +
-	      ((regs->cp0_cause & CAUSEF_BD) != 0);
-	if (!get_user(*opcode, epc))
-		return 0;
-
-	force_sig(SIGSEGV, current);
-	return 1;
-}
-
 /*
  * ll/sc emulation
  */
@@ -544,8 +533,8 @@
 {
 	unsigned int opcode;
 
-	if (unlikely(get_insn_opcode(regs, &opcode)))
-		return -EFAULT;
+	if (get_user(opcode, (unsigned int __user *) exception_epc(regs)))
+		goto out_sigsegv;
 
 	if ((opcode & OPCODE) == LL) {
 		simulate_ll(regs, opcode);
@@ -557,6 +546,10 @@
 	}
 
 	return -EFAULT;			/* Strange things going on ... */
+
+out_sigsegv:
+	force_sig(SIGSEGV, current);
+	return -EFAULT;
 }
 
 /*
@@ -569,8 +562,8 @@
 	struct thread_info *ti = task_thread_info(current);
 	unsigned int opcode;
 
-	if (unlikely(get_insn_opcode(regs, &opcode)))
-		return -EFAULT;
+	if (get_user(opcode, (unsigned int __user *) exception_epc(regs)))
+		goto out_sigsegv;
 
 	if (unlikely(compute_return_epc(regs)))
 		return -EFAULT;
@@ -589,6 +582,10 @@
 
 	/* Not ours.  */
 	return -EFAULT;
+
+out_sigsegv:
+	force_sig(SIGSEGV, current);
+	return -EFAULT;
 }
 
 asmlinkage void do_ov(struct pt_regs *regs)
@@ -672,10 +669,8 @@
 	unsigned int opcode, bcode;
 	siginfo_t info;
 
-	die_if_kernel("Break instruction in kernel code", regs);
-
-	if (get_insn_opcode(regs, &opcode))
-		return;
+	if (get_user(opcode, (unsigned int __user *) exception_epc(regs)))
+		goto out_sigsegv;
 
 	/*
 	 * There is the ancient bug in the MIPS assemblers that the break
@@ -696,6 +691,7 @@
 	switch (bcode) {
 	case BRK_OVERFLOW << 10:
 	case BRK_DIVZERO << 10:
+		die_if_kernel("Break instruction in kernel code", regs);
 		if (bcode == (BRK_DIVZERO << 10))
 			info.si_code = FPE_INTDIV;
 		else
@@ -705,9 +701,16 @@
 		info.si_addr = (void __user *) regs->cp0_epc;
 		force_sig_info(SIGFPE, &info, current);
 		break;
+	case BRK_BUG:
+		die("Kernel bug detected", regs);
+		break;
 	default:
+		die_if_kernel("Break instruction in kernel code", regs);
 		force_sig(SIGTRAP, current);
 	}
+
+out_sigsegv:
+	force_sig(SIGSEGV, current);
 }
 
 asmlinkage void do_tr(struct pt_regs *regs)
@@ -715,10 +718,8 @@
 	unsigned int opcode, tcode = 0;
 	siginfo_t info;
 
-	die_if_kernel("Trap instruction in kernel code", regs);
-
-	if (get_insn_opcode(regs, &opcode))
-		return;
+	if (get_user(opcode, (unsigned int __user *) exception_epc(regs)))
+		goto out_sigsegv;
 
 	/* Immediate versions don't provide a code.  */
 	if (!(opcode & OPCODE))
@@ -733,6 +734,7 @@
 	switch (tcode) {
 	case BRK_OVERFLOW:
 	case BRK_DIVZERO:
+		die_if_kernel("Trap instruction in kernel code", regs);
 		if (tcode == BRK_DIVZERO)
 			info.si_code = FPE_INTDIV;
 		else
@@ -742,9 +744,16 @@
 		info.si_addr = (void __user *) regs->cp0_epc;
 		force_sig_info(SIGFPE, &info, current);
 		break;
+	case BRK_BUG:
+		die("Kernel bug detected", regs);
+		break;
 	default:
+		die_if_kernel("Trap instruction in kernel code", regs);
 		force_sig(SIGTRAP, current);
 	}
+
+out_sigsegv:
+	force_sig(SIGSEGV, current);
 }
 
 asmlinkage void do_ri(struct pt_regs *regs)
@@ -1423,6 +1432,15 @@
 	memcpy((void *)(uncached_ebase + offset), addr, size);
 }
 
+static int __initdata rdhwr_noopt;
+static int __init set_rdhwr_noopt(char *str)
+{
+	rdhwr_noopt = 1;
+	return 1;
+}
+
+__setup("rdhwr_noopt", set_rdhwr_noopt);
+
 void __init trap_init(void)
 {
 	extern char except_vec3_generic, except_vec3_r4000;
@@ -1502,7 +1520,9 @@
 
 	set_except_vector(8, handle_sys);
 	set_except_vector(9, handle_bp);
-	set_except_vector(10, handle_ri);
+	set_except_vector(10, rdhwr_noopt ? handle_ri :
+			  (cpu_has_vtag_icache ?
+			   handle_ri_rdhwr_vivt : handle_ri_rdhwr));
 	set_except_vector(11, handle_cpu);
 	set_except_vector(12, handle_ov);
 	set_except_vector(13, handle_tr);
diff --git a/arch/mips/lasat/interrupt.c b/arch/mips/lasat/interrupt.c
index a144a00..4a84a7b 100644
--- a/arch/mips/lasat/interrupt.c
+++ b/arch/mips/lasat/interrupt.c
@@ -36,33 +36,14 @@
 
 void disable_lasat_irq(unsigned int irq_nr)
 {
-	unsigned long flags;
-
-	local_irq_save(flags);
 	*lasat_int_mask &= ~(1 << irq_nr) << lasat_int_mask_shift;
-	local_irq_restore(flags);
 }
 
 void enable_lasat_irq(unsigned int irq_nr)
 {
-	unsigned long flags;
-
-	local_irq_save(flags);
 	*lasat_int_mask |= (1 << irq_nr) << lasat_int_mask_shift;
-	local_irq_restore(flags);
 }
 
-static unsigned int startup_lasat_irq(unsigned int irq)
-{
-	enable_lasat_irq(irq);
-
-	return 0; /* never anything pending */
-}
-
-#define shutdown_lasat_irq	disable_lasat_irq
-
-#define mask_and_ack_lasat_irq disable_lasat_irq
-
 static void end_lasat_irq(unsigned int irq)
 {
 	if (!(irq_desc[irq].status & (IRQ_DISABLED|IRQ_INPROGRESS)))
@@ -71,11 +52,10 @@
 
 static struct irq_chip lasat_irq_type = {
 	.typename = "Lasat",
-	.startup = startup_lasat_irq,
-	.shutdown = shutdown_lasat_irq,
-	.enable = enable_lasat_irq,
-	.disable = disable_lasat_irq,
-	.ack = mask_and_ack_lasat_irq,
+	.ack = disable_lasat_irq,
+	.mask = disable_lasat_irq,
+	.mask_ack = disable_lasat_irq,
+	.unmask = enable_lasat_irq,
 	.end = end_lasat_irq,
 };
 
@@ -152,10 +132,6 @@
 		panic("arch_init_irq: mips_machtype incorrect");
 	}
 
-	for (i = 0; i <= LASATINT_END; i++) {
-		irq_desc[i].status	= IRQ_DISABLED;
-		irq_desc[i].action	= 0;
-		irq_desc[i].depth	= 1;
-		irq_desc[i].chip	= &lasat_irq_type;
-	}
+	for (i = 0; i <= LASATINT_END; i++)
+		set_irq_chip_and_handler(i, &lasat_irq_type, handle_level_irq);
 }
diff --git a/arch/mips/mips-boards/atlas/atlas_int.c b/arch/mips/mips-boards/atlas/atlas_int.c
index be624b8..43dba6c 100644
--- a/arch/mips/mips-boards/atlas/atlas_int.c
+++ b/arch/mips/mips-boards/atlas/atlas_int.c
@@ -62,16 +62,6 @@
 	iob();
 }
 
-static unsigned int startup_atlas_irq(unsigned int irq)
-{
-	enable_atlas_irq(irq);
-	return 0; /* never anything pending */
-}
-
-#define shutdown_atlas_irq	disable_atlas_irq
-
-#define mask_and_ack_atlas_irq disable_atlas_irq
-
 static void end_atlas_irq(unsigned int irq)
 {
 	if (!(irq_desc[irq].status & (IRQ_DISABLED|IRQ_INPROGRESS)))
@@ -80,11 +70,11 @@
 
 static struct irq_chip atlas_irq_type = {
 	.typename = "Atlas",
-	.startup = startup_atlas_irq,
-	.shutdown = shutdown_atlas_irq,
-	.enable = enable_atlas_irq,
-	.disable = disable_atlas_irq,
-	.ack = mask_and_ack_atlas_irq,
+	.ack = disable_atlas_irq,
+	.mask = disable_atlas_irq,
+	.mask_ack = disable_atlas_irq,
+	.unmask = enable_atlas_irq,
+	.eoi = enable_atlas_irq,
 	.end = end_atlas_irq,
 };
 
@@ -217,13 +207,8 @@
 	 */
 	atlas_hw0_icregs->intrsten = 0xffffffff;
 
-	for (i = ATLAS_INT_BASE; i <= ATLAS_INT_END; i++) {
-		irq_desc[i].status	= IRQ_DISABLED;
-		irq_desc[i].action	= 0;
-		irq_desc[i].depth	= 1;
-		irq_desc[i].chip	= &atlas_irq_type;
-		spin_lock_init(&irq_desc[i].lock);
-	}
+	for (i = ATLAS_INT_BASE; i <= ATLAS_INT_END; i++)
+		set_irq_chip_and_handler(i, &atlas_irq_type, handle_level_irq);
 }
 
 static struct irqaction atlasirq = {
diff --git a/arch/mips/mips-boards/generic/time.c b/arch/mips/mips-boards/generic/time.c
index d817c60..e4604c7 100644
--- a/arch/mips/mips-boards/generic/time.c
+++ b/arch/mips/mips-boards/generic/time.c
@@ -288,6 +288,7 @@
 	   The effect is that the int remains disabled on the second cpu.
 	   Mark the interrupt with IRQ_PER_CPU to avoid any confusion */
 	irq_desc[mips_cpu_timer_irq].status |= IRQ_PER_CPU;
+	set_irq_handler(mips_cpu_timer_irq, handle_percpu_irq);
 #endif
 
         /* to generate the first timer interrupt */
diff --git a/arch/mips/mips-boards/sim/sim_time.c b/arch/mips/mips-boards/sim/sim_time.c
index 24a4ed0..30711d0 100644
--- a/arch/mips/mips-boards/sim/sim_time.c
+++ b/arch/mips/mips-boards/sim/sim_time.c
@@ -3,6 +3,9 @@
 #include <linux/kernel_stat.h>
 #include <linux/sched.h>
 #include <linux/spinlock.h>
+#include <linux/interrupt.h>
+#include <linux/mc146818rtc.h>
+#include <linux/timex.h>
 
 #include <asm/mipsregs.h>
 #include <asm/ptrace.h>
@@ -10,24 +13,14 @@
 #include <asm/div64.h>
 #include <asm/cpu.h>
 #include <asm/time.h>
-
-#include <linux/interrupt.h>
-#include <linux/mc146818rtc.h>
-#include <linux/timex.h>
-#include <asm/mipsregs.h>
-#include <asm/hardirq.h>
 #include <asm/irq.h>
-#include <asm/div64.h>
-#include <asm/cpu.h>
-#include <asm/time.h>
 #include <asm/mc146818-time.h>
 #include <asm/msc01_ic.h>
+#include <asm/smp.h>
 
 #include <asm/mips-boards/generic.h>
 #include <asm/mips-boards/prom.h>
 #include <asm/mips-boards/simint.h>
-#include <asm/mc146818-time.h>
-#include <asm/smp.h>
 
 
 unsigned long cpu_khz;
@@ -203,7 +196,8 @@
 	   on seperate cpu's the first one tries to handle the second interrupt.
 	   The effect is that the int remains disabled on the second cpu.
 	   Mark the interrupt with IRQ_PER_CPU to avoid any confusion */
-	irq_desc[mips_cpu_timer_irq].status |= IRQ_PER_CPU;
+	irq_desc[mips_cpu_timer_irq].flags |= IRQ_PER_CPU;
+	set_irq_handler(mips_cpu_timer_irq, handle_percpu_irq);
 #endif
 
 	/* to generate the first timer interrupt */
diff --git a/arch/mips/mm/c-r4k.c b/arch/mips/mm/c-r4k.c
index cc895da..df04a31 100644
--- a/arch/mips/mm/c-r4k.c
+++ b/arch/mips/mm/c-r4k.c
@@ -323,7 +323,6 @@
 static inline void local_r4k_flush_cache_all(void * args)
 {
 	r4k_blast_dcache();
-	r4k_blast_icache();
 }
 
 static void r4k_flush_cache_all(void)
@@ -359,21 +358,19 @@
 static inline void local_r4k_flush_cache_range(void * args)
 {
 	struct vm_area_struct *vma = args;
-	int exec;
 
 	if (!(cpu_context(smp_processor_id(), vma->vm_mm)))
 		return;
 
-	exec = vma->vm_flags & VM_EXEC;
-	if (cpu_has_dc_aliases || exec)
-		r4k_blast_dcache();
-	if (exec)
-		r4k_blast_icache();
+	r4k_blast_dcache();
 }
 
 static void r4k_flush_cache_range(struct vm_area_struct *vma,
 	unsigned long start, unsigned long end)
 {
+	if (!cpu_has_dc_aliases)
+		return;
+
 	r4k_on_each_cpu(local_r4k_flush_cache_range, vma, 1, 1);
 }
 
@@ -384,18 +381,21 @@
 	if (!cpu_context(smp_processor_id(), mm))
 		return;
 
-	r4k_blast_dcache();
-	r4k_blast_icache();
-
 	/*
 	 * Kludge alert.  For obscure reasons R4000SC and R4400SC go nuts if we
 	 * only flush the primary caches but R10000 and R12000 behave sane ...
+	 * R4000SC and R4400SC indexed S-cache ops also invalidate primary
+	 * caches, so we can bail out early.
 	 */
 	if (current_cpu_data.cputype == CPU_R4000SC ||
 	    current_cpu_data.cputype == CPU_R4000MC ||
 	    current_cpu_data.cputype == CPU_R4400SC ||
-	    current_cpu_data.cputype == CPU_R4400MC)
+	    current_cpu_data.cputype == CPU_R4400MC) {
 		r4k_blast_scache();
+		return;
+	}
+
+	r4k_blast_dcache();
 }
 
 static void r4k_flush_cache_mm(struct mm_struct *mm)
diff --git a/arch/mips/mm/fault.c b/arch/mips/mm/fault.c
index 8423d85..6f90e7e 100644
--- a/arch/mips/mm/fault.c
+++ b/arch/mips/mm/fault.c
@@ -60,6 +60,10 @@
 	 */
 	if (unlikely(address >= VMALLOC_START && address <= VMALLOC_END))
 		goto vmalloc_fault;
+#ifdef MODULE_START
+	if (unlikely(address >= MODULE_START && address < MODULE_END))
+		goto vmalloc_fault;
+#endif
 
 	/*
 	 * If we're in an interrupt or have no user
diff --git a/arch/mips/mm/init.c b/arch/mips/mm/init.c
index 2de4d3c..9e29ba9 100644
--- a/arch/mips/mm/init.c
+++ b/arch/mips/mm/init.c
@@ -90,9 +90,9 @@
 	if (!empty_zero_page)
 		panic("Oh boy, that early out of memory?");
 
-	page = virt_to_page(empty_zero_page);
+	page = virt_to_page((void *)empty_zero_page);
 	split_page(page, order);
-	while (page < virt_to_page(empty_zero_page + (PAGE_SIZE << order))) {
+	while (page < virt_to_page((void *)(empty_zero_page + (PAGE_SIZE << order)))) {
 		SetPageReserved(page);
 		page++;
 	}
@@ -443,15 +443,18 @@
 }
 #endif /* !CONFIG_NEED_MULTIPLE_NODES */
 
-void free_init_pages(char *what, unsigned long begin, unsigned long end)
+static void free_init_pages(char *what, unsigned long begin, unsigned long end)
 {
-	unsigned long addr;
+	unsigned long pfn;
 
-	for (addr = begin; addr < end; addr += PAGE_SIZE) {
-		ClearPageReserved(virt_to_page(addr));
-		init_page_count(virt_to_page(addr));
-		memset((void *)addr, 0xcc, PAGE_SIZE);
-		free_page(addr);
+	for (pfn = PFN_UP(begin); pfn < PFN_DOWN(end); pfn++) {
+		struct page *page = pfn_to_page(pfn);
+		void *addr = phys_to_virt(PFN_PHYS(pfn));
+
+		ClearPageReserved(page);
+		init_page_count(page);
+		memset(addr, POISON_FREE_INITMEM, PAGE_SIZE);
+		__free_page(page);
 		totalram_pages++;
 	}
 	printk(KERN_INFO "Freeing %s: %ldk freed\n", what, (end - begin) >> 10);
@@ -460,12 +463,9 @@
 #ifdef CONFIG_BLK_DEV_INITRD
 void free_initrd_mem(unsigned long start, unsigned long end)
 {
-#ifdef CONFIG_64BIT
-	/* Switch from KSEG0 to XKPHYS addresses */
-	start = (unsigned long)phys_to_virt(CPHYSADDR(start));
-	end = (unsigned long)phys_to_virt(CPHYSADDR(end));
-#endif
-	free_init_pages("initrd memory", start, end);
+	free_init_pages("initrd memory",
+			virt_to_phys((void *)start),
+			virt_to_phys((void *)end));
 }
 #endif
 
@@ -473,17 +473,13 @@
 
 void free_initmem(void)
 {
-	unsigned long start, end, freed;
+	unsigned long freed;
 
 	freed = prom_free_prom_memory();
 	if (freed)
 		printk(KERN_INFO "Freeing firmware memory: %ldk freed\n",freed);
 
-	start = (unsigned long)(&__init_begin);
-	end = (unsigned long)(&__init_end);
-#ifdef CONFIG_64BIT
-	start = PAGE_OFFSET | CPHYSADDR(start);
-	end = PAGE_OFFSET | CPHYSADDR(end);
-#endif
-	free_init_pages("unused kernel memory", start, end);
+	free_init_pages("unused kernel memory",
+			__pa_symbol(&__init_begin),
+			__pa_symbol(&__init_end));
 }
diff --git a/arch/mips/mm/pgtable-64.c b/arch/mips/mm/pgtable-64.c
index 8d600d3..c46eb65 100644
--- a/arch/mips/mm/pgtable-64.c
+++ b/arch/mips/mm/pgtable-64.c
@@ -58,6 +58,9 @@
 
 	/* Initialize the entire pgd.  */
 	pgd_init((unsigned long)swapper_pg_dir);
+#ifdef MODULE_START
+	pgd_init((unsigned long)module_pg_dir);
+#endif
 	pmd_init((unsigned long)invalid_pmd_table, (unsigned long)invalid_pte_table);
 
 	pgd_base = swapper_pg_dir;
diff --git a/arch/mips/mm/tlbex.c b/arch/mips/mm/tlbex.c
index fec318a..492c518 100644
--- a/arch/mips/mm/tlbex.c
+++ b/arch/mips/mm/tlbex.c
@@ -423,6 +423,9 @@
 	label_invalid,
 	label_second_part,
 	label_leave,
+#ifdef MODULE_START
+	label_module_alloc,
+#endif
 	label_vmalloc,
 	label_vmalloc_done,
 	label_tlbw_hazard,
@@ -455,6 +458,9 @@
 
 L_LA(_second_part)
 L_LA(_leave)
+#ifdef MODULE_START
+L_LA(_module_alloc)
+#endif
 L_LA(_vmalloc)
 L_LA(_vmalloc_done)
 L_LA(_tlbw_hazard)
@@ -686,6 +692,13 @@
 	i_bgezl(p, reg, 0);
 }
 
+static void __init __attribute__((unused))
+il_bgez(u32 **p, struct reloc **r, unsigned int reg, enum label_id l)
+{
+	r_mips_pc16(r, *p, l);
+	i_bgez(p, reg, 0);
+}
+
 /* The only general purpose registers allowed in TLB handlers. */
 #define K0		26
 #define K1		27
@@ -970,7 +983,11 @@
 	 * The vmalloc handling is not in the hotpath.
 	 */
 	i_dmfc0(p, tmp, C0_BADVADDR);
+#ifdef MODULE_START
+	il_bltz(p, r, tmp, label_module_alloc);
+#else
 	il_bltz(p, r, tmp, label_vmalloc);
+#endif
 	/* No i_nop needed here, since the next insn doesn't touch TMP. */
 
 #ifdef CONFIG_SMP
@@ -1023,8 +1040,46 @@
 {
 	long swpd = (long)swapper_pg_dir;
 
+#ifdef MODULE_START
+	long modd = (long)module_pg_dir;
+
+	l_module_alloc(l, *p);
+	/*
+	 * Assumption:
+	 * VMALLOC_START >= 0xc000000000000000UL
+	 * MODULE_START >= 0xe000000000000000UL
+	 */
+	i_SLL(p, ptr, bvaddr, 2);
+	il_bgez(p, r, ptr, label_vmalloc);
+
+	if (in_compat_space_p(MODULE_START) && !rel_lo(MODULE_START)) {
+		i_lui(p, ptr, rel_hi(MODULE_START)); /* delay slot */
+	} else {
+		/* unlikely configuration */
+		i_nop(p); /* delay slot */
+		i_LA(p, ptr, MODULE_START);
+	}
+	i_dsubu(p, bvaddr, bvaddr, ptr);
+
+	if (in_compat_space_p(modd) && !rel_lo(modd)) {
+		il_b(p, r, label_vmalloc_done);
+		i_lui(p, ptr, rel_hi(modd));
+	} else {
+		i_LA_mostly(p, ptr, modd);
+		il_b(p, r, label_vmalloc_done);
+		i_daddiu(p, ptr, ptr, rel_lo(modd));
+	}
+
+	l_vmalloc(l, *p);
+	if (in_compat_space_p(MODULE_START) && !rel_lo(MODULE_START) &&
+	    MODULE_START << 32 == VMALLOC_START)
+		i_dsll32(p, ptr, ptr, 0);	/* typical case */
+	else
+		i_LA(p, ptr, VMALLOC_START);
+#else
 	l_vmalloc(l, *p);
 	i_LA(p, ptr, VMALLOC_START);
+#endif
 	i_dsubu(p, bvaddr, bvaddr, ptr);
 
 	if (in_compat_space_p(swpd) && !rel_lo(swpd)) {
diff --git a/arch/mips/momentum/ocelot_c/cpci-irq.c b/arch/mips/momentum/ocelot_c/cpci-irq.c
index 47e3fa3..e5a4a0a 100644
--- a/arch/mips/momentum/ocelot_c/cpci-irq.c
+++ b/arch/mips/momentum/ocelot_c/cpci-irq.c
@@ -66,39 +66,6 @@
 }
 
 /*
- * Enables the IRQ in the FPGA
- */
-static void enable_cpci_irq(unsigned int irq)
-{
-	unmask_cpci_irq(irq);
-}
-
-/*
- * Initialize the IRQ in the FPGA
- */
-static unsigned int startup_cpci_irq(unsigned int irq)
-{
-	unmask_cpci_irq(irq);
-	return 0;
-}
-
-/*
- * Disables the IRQ in the FPGA
- */
-static void disable_cpci_irq(unsigned int irq)
-{
-	mask_cpci_irq(irq);
-}
-
-/*
- * Masks and ACKs an IRQ
- */
-static void mask_and_ack_cpci_irq(unsigned int irq)
-{
-	mask_cpci_irq(irq);
-}
-
-/*
  * End IRQ processing
  */
 static void end_cpci_irq(unsigned int irq)
@@ -125,15 +92,12 @@
 	do_IRQ(ls1bit8(irq_src) + CPCI_IRQ_BASE);
 }
 
-#define shutdown_cpci_irq	disable_cpci_irq
-
 struct irq_chip cpci_irq_type = {
 	.typename = "CPCI/FPGA",
-	.startup = startup_cpci_irq,
-	.shutdown = shutdown_cpci_irq,
-	.enable = enable_cpci_irq,
-	.disable = disable_cpci_irq,
-	.ack = mask_and_ack_cpci_irq,
+	.ack = mask_cpci_irq,
+	.mask = mask_cpci_irq,
+	.mask_ack = mask_cpci_irq,
+	.unmask = unmask_cpci_irq,
 	.end = end_cpci_irq,
 };
 
@@ -141,11 +105,6 @@
 {
 	int i;
 
-	/* Reset irq handlers pointers to NULL */
-	for (i = CPCI_IRQ_BASE; i < (CPCI_IRQ_BASE + 8); i++) {
-		irq_desc[i].status = IRQ_DISABLED;
-		irq_desc[i].action = 0;
-		irq_desc[i].depth = 2;
-		irq_desc[i].chip = &cpci_irq_type;
-	}
+	for (i = CPCI_IRQ_BASE; i < (CPCI_IRQ_BASE + 8); i++)
+		set_irq_chip_and_handler(i, &cpci_irq_type, handle_level_irq);
 }
diff --git a/arch/mips/momentum/ocelot_c/uart-irq.c b/arch/mips/momentum/ocelot_c/uart-irq.c
index 510257d..0029f00 100644
--- a/arch/mips/momentum/ocelot_c/uart-irq.c
+++ b/arch/mips/momentum/ocelot_c/uart-irq.c
@@ -60,39 +60,6 @@
 }
 
 /*
- * Enables the IRQ in the FPGA
- */
-static void enable_uart_irq(unsigned int irq)
-{
-	unmask_uart_irq(irq);
-}
-
-/*
- * Initialize the IRQ in the FPGA
- */
-static unsigned int startup_uart_irq(unsigned int irq)
-{
-	unmask_uart_irq(irq);
-	return 0;
-}
-
-/*
- * Disables the IRQ in the FPGA
- */
-static void disable_uart_irq(unsigned int irq)
-{
-	mask_uart_irq(irq);
-}
-
-/*
- * Masks and ACKs an IRQ
- */
-static void mask_and_ack_uart_irq(unsigned int irq)
-{
-	mask_uart_irq(irq);
-}
-
-/*
  * End IRQ processing
  */
 static void end_uart_irq(unsigned int irq)
@@ -118,28 +85,17 @@
 	do_IRQ(ls1bit8(irq_src) + 74);
 }
 
-#define shutdown_uart_irq	disable_uart_irq
-
 struct irq_chip uart_irq_type = {
 	.typename = "UART/FPGA",
-	.startup = startup_uart_irq,
-	.shutdown = shutdown_uart_irq,
-	.enable = enable_uart_irq,
-	.disable = disable_uart_irq,
-	.ack = mask_and_ack_uart_irq,
+	.ack = mask_uart_irq,
+	.mask = mask_uart_irq,
+	.mask_ack = mask_uart_irq,
+	.unmask = unmask_uart_irq,
 	.end = end_uart_irq,
 };
 
 void uart_irq_init(void)
 {
-	/* Reset irq handlers pointers to NULL */
-	irq_desc[80].status = IRQ_DISABLED;
-	irq_desc[80].action = 0;
-	irq_desc[80].depth = 2;
-	irq_desc[80].chip = &uart_irq_type;
-
-	irq_desc[81].status = IRQ_DISABLED;
-	irq_desc[81].action = 0;
-	irq_desc[81].depth = 2;
-	irq_desc[81].chip = &uart_irq_type;
+	set_irq_chip_and_handler(80, &uart_irq_type, handle_level_irq);
+	set_irq_chip_and_handler(81, &uart_irq_type, handle_level_irq);
 }
diff --git a/arch/mips/oprofile/Makefile b/arch/mips/oprofile/Makefile
index 0a50aad..bf3be6f 100644
--- a/arch/mips/oprofile/Makefile
+++ b/arch/mips/oprofile/Makefile
@@ -12,5 +12,6 @@
 
 oprofile-$(CONFIG_CPU_MIPS32)		+= op_model_mipsxx.o
 oprofile-$(CONFIG_CPU_MIPS64)		+= op_model_mipsxx.o
+oprofile-$(CONFIG_CPU_R10000)		+= op_model_mipsxx.o
 oprofile-$(CONFIG_CPU_SB1)		+= op_model_mipsxx.o
 oprofile-$(CONFIG_CPU_RM9000)		+= op_model_rm9000.o
diff --git a/arch/mips/oprofile/common.c b/arch/mips/oprofile/common.c
index 65eb554..4e0a90b 100644
--- a/arch/mips/oprofile/common.c
+++ b/arch/mips/oprofile/common.c
@@ -83,6 +83,9 @@
 	case CPU_74K:
 	case CPU_SB1:
 	case CPU_SB1A:
+	case CPU_R10000:
+	case CPU_R12000:
+	case CPU_R14000:
 		lmodel = &op_model_mipsxx_ops;
 		break;
 
diff --git a/arch/mips/oprofile/op_model_mipsxx.c b/arch/mips/oprofile/op_model_mipsxx.c
index 1fb240c..455d76a 100644
--- a/arch/mips/oprofile/op_model_mipsxx.c
+++ b/arch/mips/oprofile/op_model_mipsxx.c
@@ -18,7 +18,7 @@
 #define M_PERFCTL_SUPERVISOR		(1UL      <<  2)
 #define M_PERFCTL_USER			(1UL      <<  3)
 #define M_PERFCTL_INTERRUPT_ENABLE	(1UL      <<  4)
-#define M_PERFCTL_EVENT(event)		((event)  << 5)
+#define M_PERFCTL_EVENT(event)		(((event) & 0x3f)  << 5)
 #define M_PERFCTL_VPEID(vpe)		((vpe)    << 16)
 #define M_PERFCTL_MT_EN(filter)		((filter) << 20)
 #define    M_TC_EN_ALL			M_PERFCTL_MT_EN(0)
@@ -218,13 +218,23 @@
 
 static inline int n_counters(void)
 {
-	int counters = __n_counters();
+	int counters;
+
+	switch (current_cpu_data.cputype) {
+	case CPU_R10000:
+		counters = 2;
+
+	case CPU_R12000:
+	case CPU_R14000:
+		counters = 4;
+
+	default:
+		counters = __n_counters();
+	}
 
 #ifdef CONFIG_MIPS_MT_SMP
-	if (current_cpu_data.cputype == CPU_34K)
-		return counters >> 1;
+	counters >> 1;
 #endif
-
 	return counters;
 }
 
@@ -284,6 +294,18 @@
 		op_model_mipsxx_ops.cpu_type = "mips/5K";
 		break;
 
+	case CPU_R10000:
+		if ((current_cpu_data.processor_id & 0xff) == 0x20)
+			op_model_mipsxx_ops.cpu_type = "mips/r10000-v2.x";
+		else
+			op_model_mipsxx_ops.cpu_type = "mips/r10000";
+		break;
+
+	case CPU_R12000:
+	case CPU_R14000:
+		op_model_mipsxx_ops.cpu_type = "mips/r12000";
+		break;
+
 	case CPU_SB1:
 	case CPU_SB1A:
 		op_model_mipsxx_ops.cpu_type = "mips/sb1";
diff --git a/arch/mips/pci/fixup-cobalt.c b/arch/mips/pci/fixup-cobalt.c
index 75a01e7..7d5f6bb 100644
--- a/arch/mips/pci/fixup-cobalt.c
+++ b/arch/mips/pci/fixup-cobalt.c
@@ -94,22 +94,21 @@
 #if 0
 	if (galileo_id >= 0x10) {
 		/* New Galileo, assumes PCI stop line to VIA is connected. */
-		GALILEO_OUTL(0x4020, GT_PCI0_TOR_OFS);
+		GT_WRITE(GT_PCI0_TOR_OFS, 0x4020);
 	} else if (galileo_id == 0x1 || galileo_id == 0x2)
 #endif
 	{
 		signed int timeo;
 		/* XXX WE MUST DO THIS ELSE GALILEO LOCKS UP! -DaveM */
-		timeo = GALILEO_INL(GT_PCI0_TOR_OFS);
+		timeo = GT_READ(GT_PCI0_TOR_OFS);
 		/* Old Galileo, assumes PCI STOP line to VIA is disconnected. */
-		GALILEO_OUTL(
+		GT_WRITE(GT_PCI0_TOR_OFS,
 			(0xff << 16) |		/* retry count */
 			(0xff << 8) |		/* timeout 1   */
-			0xff,			/* timeout 0   */
-			GT_PCI0_TOR_OFS);
+			0xff);			/* timeout 0   */
 
 		/* enable PCI retry exceeded interrupt */
-		GALILEO_OUTL(GALILEO_INTR_RETRY_CTR | GALILEO_INL(GT_INTRMASK_OFS), GT_INTRMASK_OFS);
+		GT_WRITE(GT_INTRMASK_OFS, GT_INTR_RETRYCTR0_MSK | GT_READ(GT_INTRMASK_OFS));
 	}
 }
 
diff --git a/arch/mips/pci/ops-gt64111.c b/arch/mips/pci/ops-gt64111.c
index 13de459..ecd3991 100644
--- a/arch/mips/pci/ops-gt64111.c
+++ b/arch/mips/pci/ops-gt64111.c
@@ -38,18 +38,18 @@
 	switch (size) {
 	case 4:
 		PCI_CFG_SET(devfn, where);
-		*val = GALILEO_INL(GT_PCI0_CFGDATA_OFS);
+		*val = GT_READ(GT_PCI0_CFGDATA_OFS);
 		return PCIBIOS_SUCCESSFUL;
 
 	case 2:
 		PCI_CFG_SET(devfn, (where & ~0x3));
-		*val = GALILEO_INL(GT_PCI0_CFGDATA_OFS)
+		*val = GT_READ(GT_PCI0_CFGDATA_OFS)
 		    >> ((where & 3) * 8);
 		return PCIBIOS_SUCCESSFUL;
 
 	case 1:
 		PCI_CFG_SET(devfn, (where & ~0x3));
-		*val = GALILEO_INL(GT_PCI0_CFGDATA_OFS)
+		*val = GT_READ(GT_PCI0_CFGDATA_OFS)
 		    >> ((where & 3) * 8);
 		return PCIBIOS_SUCCESSFUL;
 	}
@@ -68,25 +68,25 @@
 	switch (size) {
 	case 4:
 		PCI_CFG_SET(devfn, where);
-		GALILEO_OUTL(val, GT_PCI0_CFGDATA_OFS);
+		GT_WRITE(GT_PCI0_CFGDATA_OFS, val);
 
 		return PCIBIOS_SUCCESSFUL;
 
 	case 2:
 		PCI_CFG_SET(devfn, (where & ~0x3));
-		tmp = GALILEO_INL(GT_PCI0_CFGDATA_OFS);
+		tmp = GT_READ(GT_PCI0_CFGDATA_OFS);
 		tmp &= ~(0xffff << ((where & 0x3) * 8));
 		tmp |= (val << ((where & 0x3) * 8));
-		GALILEO_OUTL(tmp, GT_PCI0_CFGDATA_OFS);
+		GT_WRITE(GT_PCI0_CFGDATA_OFS, tmp);
 
 		return PCIBIOS_SUCCESSFUL;
 
 	case 1:
 		PCI_CFG_SET(devfn, (where & ~0x3));
-		tmp = GALILEO_INL(GT_PCI0_CFGDATA_OFS);
+		tmp = GT_READ(GT_PCI0_CFGDATA_OFS);
 		tmp &= ~(0xff << ((where & 0x3) * 8));
 		tmp |= (val << ((where & 0x3) * 8));
-		GALILEO_OUTL(tmp, GT_PCI0_CFGDATA_OFS);
+		GT_WRITE(GT_PCI0_CFGDATA_OFS, tmp);
 
 		return PCIBIOS_SUCCESSFUL;
 	}
diff --git a/arch/mips/philips/pnx8550/common/int.c b/arch/mips/philips/pnx8550/common/int.c
index 7106116..0dc2393 100644
--- a/arch/mips/philips/pnx8550/common/int.c
+++ b/arch/mips/philips/pnx8550/common/int.c
@@ -38,8 +38,6 @@
 #include <int.h>
 #include <uart.h>
 
-static DEFINE_SPINLOCK(irq_lock);
-
 /* default prio for interrupts */
 /* first one is a no-no so therefore always prio 0 (disabled) */
 static char gic_prio[PNX8550_INT_GIC_TOTINT] = {
@@ -149,38 +147,6 @@
 	}
 }
 
-#define pnx8550_disable pnx8550_ack
-static void pnx8550_ack(unsigned int irq)
-{
-	unsigned long flags;
-
-	spin_lock_irqsave(&irq_lock, flags);
-	mask_irq(irq);
-	spin_unlock_irqrestore(&irq_lock, flags);
-}
-
-#define pnx8550_enable pnx8550_unmask
-static void pnx8550_unmask(unsigned int irq)
-{
-	unsigned long flags;
-
-	spin_lock_irqsave(&irq_lock, flags);
-	unmask_irq(irq);
-	spin_unlock_irqrestore(&irq_lock, flags);
-}
-
-static unsigned int startup_irq(unsigned int irq_nr)
-{
-	pnx8550_unmask(irq_nr);
-	return 0;
-}
-
-static void shutdown_irq(unsigned int irq_nr)
-{
-	pnx8550_ack(irq_nr);
-	return;
-}
-
 int pnx8550_set_gic_priority(int irq, int priority)
 {
 	int gic_irq = irq-PNX8550_INT_GIC_MIN;
@@ -192,26 +158,19 @@
 	return prev_priority;
 }
 
-static inline void mask_and_ack_level_irq(unsigned int irq)
-{
-	pnx8550_disable(irq);
-	return;
-}
-
 static void end_irq(unsigned int irq)
 {
 	if (!(irq_desc[irq].status & (IRQ_DISABLED|IRQ_INPROGRESS))) {
-		pnx8550_enable(irq);
+		unmask_irq(irq);
 	}
 }
 
 static struct irq_chip level_irq_type = {
 	.typename =	"PNX Level IRQ",
-	.startup =	startup_irq,
-	.shutdown =	shutdown_irq,
-	.enable =	pnx8550_enable,
-	.disable =	pnx8550_disable,
-	.ack =		mask_and_ack_level_irq,
+	.ack =		mask_irq,
+	.mask =		mask_irq,
+	.mask_ack =	mask_irq,
+	.unmask =	unmask_irq,
 	.end =		end_irq,
 };
 
@@ -233,8 +192,8 @@
 	int configPR;
 
 	for (i = 0; i < PNX8550_INT_CP0_TOTINT; i++) {
-		irq_desc[i].chip = &level_irq_type;
-		pnx8550_ack(i);	/* mask the irq just in case  */
+		set_irq_chip_and_handler(i, &level_irq_type, handle_level_irq);
+		mask_irq(i);	/* mask the irq just in case  */
 	}
 
 	/* init of GIC/IPC interrupts */
@@ -270,7 +229,7 @@
 		/* mask/priority is still 0 so we will not get any
 		 * interrupts until it is unmasked */
 
-		irq_desc[i].chip = &level_irq_type;
+		set_irq_chip_and_handler(i, &level_irq_type, handle_level_irq);
 	}
 
 	/* Priority level 0 */
@@ -279,20 +238,21 @@
 	/* Set int vector table address */
 	PNX8550_GIC_VECTOR_0 = PNX8550_GIC_VECTOR_1 = 0;
 
-	irq_desc[MIPS_CPU_GIC_IRQ].chip = &level_irq_type;
+	set_irq_chip_and_handler(MIPS_CPU_GIC_IRQ, &level_irq_type,
+				 handle_level_irq);
 	setup_irq(MIPS_CPU_GIC_IRQ, &gic_action);
 
 	/* init of Timer interrupts */
-	for (i = PNX8550_INT_TIMER_MIN; i <= PNX8550_INT_TIMER_MAX; i++) {
-		irq_desc[i].chip = &level_irq_type;
-	}
+	for (i = PNX8550_INT_TIMER_MIN; i <= PNX8550_INT_TIMER_MAX; i++)
+		set_irq_chip_and_handler(i, &level_irq_type, handle_level_irq);
 
 	/* Stop Timer 1-3 */
 	configPR = read_c0_config7();
 	configPR |= 0x00000038;
 	write_c0_config7(configPR);
 
-	irq_desc[MIPS_CPU_TIMER_IRQ].chip = &level_irq_type;
+	set_irq_chip_and_handler(MIPS_CPU_TIMER_IRQ, &level_irq_type,
+				 handle_level_irq);
 	setup_irq(MIPS_CPU_TIMER_IRQ, &timer_action);
 }
 
diff --git a/arch/mips/pmc-sierra/yosemite/smp.c b/arch/mips/pmc-sierra/yosemite/smp.c
index 3cc0436..305491e 100644
--- a/arch/mips/pmc-sierra/yosemite/smp.c
+++ b/arch/mips/pmc-sierra/yosemite/smp.c
@@ -99,8 +99,6 @@
  */
 void prom_init_secondary(void)
 {
-	mips_hpt_init();
-
 	set_c0_status(ST0_CO | ST0_IE | ST0_IM);
 }
 
diff --git a/arch/mips/sgi-ip22/ip22-eisa.c b/arch/mips/sgi-ip22/ip22-eisa.c
index 0d18ed4..a1a9af6 100644
--- a/arch/mips/sgi-ip22/ip22-eisa.c
+++ b/arch/mips/sgi-ip22/ip22-eisa.c
@@ -95,16 +95,11 @@
 
 static void enable_eisa1_irq(unsigned int irq)
 {
-	unsigned long flags;
 	u8 mask;
 
-	local_irq_save(flags);
-
 	mask = inb(EISA_INT1_MASK);
 	mask &= ~((u8) (1 << irq));
 	outb(mask, EISA_INT1_MASK);
-
-	local_irq_restore(flags);
 }
 
 static unsigned int startup_eisa1_irq(unsigned int irq)
@@ -130,8 +125,6 @@
 	outb(mask, EISA_INT1_MASK);
 }
 
-#define shutdown_eisa1_irq	disable_eisa1_irq
-
 static void mask_and_ack_eisa1_irq(unsigned int irq)
 {
 	disable_eisa1_irq(irq);
@@ -148,25 +141,20 @@
 static struct irq_chip ip22_eisa1_irq_type = {
 	.typename	= "IP22 EISA",
 	.startup	= startup_eisa1_irq,
-	.shutdown	= shutdown_eisa1_irq,
-	.enable		= enable_eisa1_irq,
-	.disable	= disable_eisa1_irq,
 	.ack		= mask_and_ack_eisa1_irq,
+	.mask		= disable_eisa1_irq,
+	.mask_ack	= mask_and_ack_eisa1_irq,
+	.unmask		= enable_eisa1_irq,
 	.end		= end_eisa1_irq,
 };
 
 static void enable_eisa2_irq(unsigned int irq)
 {
-	unsigned long flags;
 	u8 mask;
 
-	local_irq_save(flags);
-
 	mask = inb(EISA_INT2_MASK);
 	mask &= ~((u8) (1 << (irq - 8)));
 	outb(mask, EISA_INT2_MASK);
-
-	local_irq_restore(flags);
 }
 
 static unsigned int startup_eisa2_irq(unsigned int irq)
@@ -192,8 +180,6 @@
 	outb(mask, EISA_INT2_MASK);
 }
 
-#define shutdown_eisa2_irq	disable_eisa2_irq
-
 static void mask_and_ack_eisa2_irq(unsigned int irq)
 {
 	disable_eisa2_irq(irq);
@@ -210,10 +196,10 @@
 static struct irq_chip ip22_eisa2_irq_type = {
 	.typename	= "IP22 EISA",
 	.startup	= startup_eisa2_irq,
-	.shutdown	= shutdown_eisa2_irq,
-	.enable		= enable_eisa2_irq,
-	.disable	= disable_eisa2_irq,
 	.ack		= mask_and_ack_eisa2_irq,
+	.mask		= disable_eisa2_irq,
+	.mask_ack	= mask_and_ack_eisa2_irq,
+	.unmask		= enable_eisa2_irq,
 	.end		= end_eisa2_irq,
 };
 
@@ -275,13 +261,10 @@
 	outb(0, EISA_DMA2_WRITE_SINGLE);
 
 	for (i = SGINT_EISA; i < (SGINT_EISA + EISA_MAX_IRQ); i++) {
-		irq_desc[i].status = IRQ_DISABLED;
-		irq_desc[i].action = 0;
-		irq_desc[i].depth = 1;
 		if (i < (SGINT_EISA + 8))
-			irq_desc[i].chip = &ip22_eisa1_irq_type;
+			set_irq_chip(i, &ip22_eisa1_irq_type);
 		else
-			irq_desc[i].chip = &ip22_eisa2_irq_type;
+			set_irq_chip(i, &ip22_eisa2_irq_type);
 	}
 
 	/* Cannot use request_irq because of kmalloc not being ready at such
diff --git a/arch/mips/sgi-ip22/ip22-int.c b/arch/mips/sgi-ip22/ip22-int.c
index af51889..c7b1380 100644
--- a/arch/mips/sgi-ip22/ip22-int.c
+++ b/arch/mips/sgi-ip22/ip22-int.c
@@ -40,34 +40,17 @@
 
 static void enable_local0_irq(unsigned int irq)
 {
-	unsigned long flags;
-
-	local_irq_save(flags);
 	/* don't allow mappable interrupt to be enabled from setup_irq,
 	 * we have our own way to do so */
 	if (irq != SGI_MAP_0_IRQ)
 		sgint->imask0 |= (1 << (irq - SGINT_LOCAL0));
-	local_irq_restore(flags);
-}
-
-static unsigned int startup_local0_irq(unsigned int irq)
-{
-	enable_local0_irq(irq);
-	return 0;		/* Never anything pending  */
 }
 
 static void disable_local0_irq(unsigned int irq)
 {
-	unsigned long flags;
-
-	local_irq_save(flags);
 	sgint->imask0 &= ~(1 << (irq - SGINT_LOCAL0));
-	local_irq_restore(flags);
 }
 
-#define shutdown_local0_irq	disable_local0_irq
-#define mask_and_ack_local0_irq	disable_local0_irq
-
 static void end_local0_irq (unsigned int irq)
 {
 	if (!(irq_desc[irq].status & (IRQ_DISABLED|IRQ_INPROGRESS)))
@@ -76,44 +59,26 @@
 
 static struct irq_chip ip22_local0_irq_type = {
 	.typename	= "IP22 local 0",
-	.startup	= startup_local0_irq,
-	.shutdown	= shutdown_local0_irq,
-	.enable		= enable_local0_irq,
-	.disable	= disable_local0_irq,
-	.ack		= mask_and_ack_local0_irq,
+	.ack		= disable_local0_irq,
+	.mask		= disable_local0_irq,
+	.mask_ack	= disable_local0_irq,
+	.unmask		= enable_local0_irq,
 	.end		= end_local0_irq,
 };
 
 static void enable_local1_irq(unsigned int irq)
 {
-	unsigned long flags;
-
-	local_irq_save(flags);
 	/* don't allow mappable interrupt to be enabled from setup_irq,
 	 * we have our own way to do so */
 	if (irq != SGI_MAP_1_IRQ)
 		sgint->imask1 |= (1 << (irq - SGINT_LOCAL1));
-	local_irq_restore(flags);
-}
-
-static unsigned int startup_local1_irq(unsigned int irq)
-{
-	enable_local1_irq(irq);
-	return 0;		/* Never anything pending  */
 }
 
 void disable_local1_irq(unsigned int irq)
 {
-	unsigned long flags;
-
-	local_irq_save(flags);
 	sgint->imask1 &= ~(1 << (irq - SGINT_LOCAL1));
-	local_irq_restore(flags);
 }
 
-#define shutdown_local1_irq	disable_local1_irq
-#define mask_and_ack_local1_irq	disable_local1_irq
-
 static void end_local1_irq (unsigned int irq)
 {
 	if (!(irq_desc[irq].status & (IRQ_DISABLED|IRQ_INPROGRESS)))
@@ -122,44 +87,26 @@
 
 static struct irq_chip ip22_local1_irq_type = {
 	.typename	= "IP22 local 1",
-	.startup	= startup_local1_irq,
-	.shutdown	= shutdown_local1_irq,
-	.enable		= enable_local1_irq,
-	.disable	= disable_local1_irq,
-	.ack		= mask_and_ack_local1_irq,
+	.ack		= disable_local1_irq,
+	.mask		= disable_local1_irq,
+	.mask_ack	= disable_local1_irq,
+	.unmask		= enable_local1_irq,
 	.end		= end_local1_irq,
 };
 
 static void enable_local2_irq(unsigned int irq)
 {
-	unsigned long flags;
-
-	local_irq_save(flags);
 	sgint->imask0 |= (1 << (SGI_MAP_0_IRQ - SGINT_LOCAL0));
 	sgint->cmeimask0 |= (1 << (irq - SGINT_LOCAL2));
-	local_irq_restore(flags);
-}
-
-static unsigned int startup_local2_irq(unsigned int irq)
-{
-	enable_local2_irq(irq);
-	return 0;		/* Never anything pending  */
 }
 
 void disable_local2_irq(unsigned int irq)
 {
-	unsigned long flags;
-
-	local_irq_save(flags);
 	sgint->cmeimask0 &= ~(1 << (irq - SGINT_LOCAL2));
 	if (!sgint->cmeimask0)
 		sgint->imask0 &= ~(1 << (SGI_MAP_0_IRQ - SGINT_LOCAL0));
-	local_irq_restore(flags);
 }
 
-#define shutdown_local2_irq disable_local2_irq
-#define mask_and_ack_local2_irq	disable_local2_irq
-
 static void end_local2_irq (unsigned int irq)
 {
 	if (!(irq_desc[irq].status & (IRQ_DISABLED|IRQ_INPROGRESS)))
@@ -168,44 +115,26 @@
 
 static struct irq_chip ip22_local2_irq_type = {
 	.typename	= "IP22 local 2",
-	.startup	= startup_local2_irq,
-	.shutdown	= shutdown_local2_irq,
-	.enable		= enable_local2_irq,
-	.disable	= disable_local2_irq,
-	.ack		= mask_and_ack_local2_irq,
+	.ack		= disable_local2_irq,
+	.mask		= disable_local2_irq,
+	.mask_ack	= disable_local2_irq,
+	.unmask		= enable_local2_irq,
 	.end		= end_local2_irq,
 };
 
 static void enable_local3_irq(unsigned int irq)
 {
-	unsigned long flags;
-
-	local_irq_save(flags);
 	sgint->imask1 |= (1 << (SGI_MAP_1_IRQ - SGINT_LOCAL1));
 	sgint->cmeimask1 |= (1 << (irq - SGINT_LOCAL3));
-	local_irq_restore(flags);
-}
-
-static unsigned int startup_local3_irq(unsigned int irq)
-{
-	enable_local3_irq(irq);
-	return 0;		/* Never anything pending  */
 }
 
 void disable_local3_irq(unsigned int irq)
 {
-	unsigned long flags;
-
-	local_irq_save(flags);
 	sgint->cmeimask1 &= ~(1 << (irq - SGINT_LOCAL3));
 	if (!sgint->cmeimask1)
 		sgint->imask1 &= ~(1 << (SGI_MAP_1_IRQ - SGINT_LOCAL1));
-	local_irq_restore(flags);
 }
 
-#define shutdown_local3_irq disable_local3_irq
-#define mask_and_ack_local3_irq	disable_local3_irq
-
 static void end_local3_irq (unsigned int irq)
 {
 	if (!(irq_desc[irq].status & (IRQ_DISABLED|IRQ_INPROGRESS)))
@@ -214,11 +143,10 @@
 
 static struct irq_chip ip22_local3_irq_type = {
 	.typename	= "IP22 local 3",
-	.startup	= startup_local3_irq,
-	.shutdown	= shutdown_local3_irq,
-	.enable		= enable_local3_irq,
-	.disable	= disable_local3_irq,
-	.ack		= mask_and_ack_local3_irq,
+	.ack		= disable_local3_irq,
+	.mask		= disable_local3_irq,
+	.mask_ack	= disable_local3_irq,
+	.unmask		= enable_local3_irq,
 	.end		= end_local3_irq,
 };
 
@@ -430,10 +358,7 @@
 		else
 			handler		= &ip22_local3_irq_type;
 
-		irq_desc[i].status	= IRQ_DISABLED;
-		irq_desc[i].action	= 0;
-		irq_desc[i].depth	= 1;
-		irq_desc[i].chip	= handler;
+		set_irq_chip_and_handler(i, handler, handle_level_irq);
 	}
 
 	/* vector handler. this register the IRQ as non-sharable */
diff --git a/arch/mips/sgi-ip27/ip27-irq.c b/arch/mips/sgi-ip27/ip27-irq.c
index 270ecd3..5f8835b 100644
--- a/arch/mips/sgi-ip27/ip27-irq.c
+++ b/arch/mips/sgi-ip27/ip27-irq.c
@@ -332,11 +332,6 @@
 	intr_disconnect_level(cpu, swlevel);
 }
 
-static void mask_and_ack_bridge_irq(unsigned int irq)
-{
-	disable_bridge_irq(irq);
-}
-
 static void end_bridge_irq(unsigned int irq)
 {
 	if (!(irq_desc[irq].status & (IRQ_DISABLED|IRQ_INPROGRESS)) &&
@@ -348,18 +343,16 @@
 	.typename	= "bridge",
 	.startup	= startup_bridge_irq,
 	.shutdown	= shutdown_bridge_irq,
-	.enable		= enable_bridge_irq,
-	.disable	= disable_bridge_irq,
-	.ack		= mask_and_ack_bridge_irq,
+	.ack		= disable_bridge_irq,
+	.mask		= disable_bridge_irq,
+	.mask_ack	= disable_bridge_irq,
+	.unmask		= enable_bridge_irq,
 	.end		= end_bridge_irq,
 };
 
 void __devinit register_bridge_irq(unsigned int irq)
 {
-	irq_desc[irq].status	= IRQ_DISABLED;
-	irq_desc[irq].action	= 0;
-	irq_desc[irq].depth	= 1;
-	irq_desc[irq].chip	= &bridge_irq_type;
+	set_irq_chip_and_handler(irq, &bridge_irq_type, handle_level_irq);
 }
 
 int __devinit request_bridge_irq(struct bridge_controller *bc)
diff --git a/arch/mips/sgi-ip27/ip27-timer.c b/arch/mips/sgi-ip27/ip27-timer.c
index 5e82a26..7d36172 100644
--- a/arch/mips/sgi-ip27/ip27-timer.c
+++ b/arch/mips/sgi-ip27/ip27-timer.c
@@ -172,15 +172,6 @@
         return mktime(year, month, date, hour, min, sec);
 }
 
-static unsigned int startup_rt_irq(unsigned int irq)
-{
-	return 0;
-}
-
-static void shutdown_rt_irq(unsigned int irq)
-{
-}
-
 static void enable_rt_irq(unsigned int irq)
 {
 }
@@ -189,21 +180,17 @@
 {
 }
 
-static void mask_and_ack_rt(unsigned int irq)
-{
-}
-
 static void end_rt_irq(unsigned int irq)
 {
 }
 
 static struct irq_chip rt_irq_type = {
 	.typename	= "SN HUB RT timer",
-	.startup	= startup_rt_irq,
-	.shutdown	= shutdown_rt_irq,
-	.enable		= enable_rt_irq,
-	.disable	= disable_rt_irq,
-	.ack		= mask_and_ack_rt,
+	.ack		= disable_rt_irq,
+	.mask		= disable_rt_irq,
+	.mask_ack	= disable_rt_irq,
+	.unmask		= enable_rt_irq,
+	.eoi		= enable_rt_irq,
 	.end		= end_rt_irq,
 };
 
@@ -221,10 +208,7 @@
 	if (irqno < 0)
 		panic("Can't allocate interrupt number for timer interrupt");
 
-	irq_desc[irqno].status	= IRQ_DISABLED;
-	irq_desc[irqno].action	= NULL;
-	irq_desc[irqno].depth	= 1;
-	irq_desc[irqno].chip	= &rt_irq_type;
+	set_irq_chip_and_handler(irqno, &rt_irq_type, handle_percpu_irq);
 
 	/* over-write the handler, we use our own way */
 	irq->handler = no_action;
@@ -239,14 +223,14 @@
 	setup_irq(irqno, &rt_irqaction);
 }
 
-static unsigned int ip27_hpt_read(void)
+static cycle_t ip27_hpt_read(void)
 {
 	return REMOTE_HUB_L(cputonasid(0), PI_RT_COUNT);
 }
 
 void __init ip27_time_init(void)
 {
-	mips_hpt_read = ip27_hpt_read;
+	clocksource_mips.read = ip27_hpt_read;
 	mips_hpt_frequency = CYCLES_PER_SEC;
 	xtime.tv_sec = get_m48t35_time();
 	xtime.tv_nsec = 0;
diff --git a/arch/mips/sgi-ip32/ip32-irq.c b/arch/mips/sgi-ip32/ip32-irq.c
index c9acadd..ae06386 100644
--- a/arch/mips/sgi-ip32/ip32-irq.c
+++ b/arch/mips/sgi-ip32/ip32-irq.c
@@ -113,12 +113,6 @@
  * is quite different anyway.
  */
 
-/*
- * IRQ spinlock - Ralf says not to disable CPU interrupts,
- * and I think he knows better.
- */
-static DEFINE_SPINLOCK(ip32_irq_lock);
-
 /* Some initial interrupts to set up */
 extern irqreturn_t crime_memerr_intr(int irq, void *dev_id);
 extern irqreturn_t crime_cpuerr_intr(int irq, void *dev_id);
@@ -138,12 +132,6 @@
 	set_c0_status(STATUSF_IP7);
 }
 
-static unsigned int startup_cpu_irq(unsigned int irq)
-{
-	enable_cpu_irq(irq);
-	return 0;
-}
-
 static void disable_cpu_irq(unsigned int irq)
 {
 	clear_c0_status(STATUSF_IP7);
@@ -155,16 +143,12 @@
 		enable_cpu_irq (irq);
 }
 
-#define shutdown_cpu_irq disable_cpu_irq
-#define mask_and_ack_cpu_irq disable_cpu_irq
-
 static struct irq_chip ip32_cpu_interrupt = {
 	.typename = "IP32 CPU",
-	.startup = startup_cpu_irq,
-	.shutdown = shutdown_cpu_irq,
-	.enable = enable_cpu_irq,
-	.disable = disable_cpu_irq,
-	.ack = mask_and_ack_cpu_irq,
+	.ack = disable_cpu_irq,
+	.mask = disable_cpu_irq,
+	.mask_ack = disable_cpu_irq,
+	.unmask = enable_cpu_irq,
 	.end = end_cpu_irq,
 };
 
@@ -177,45 +161,27 @@
 
 static void enable_crime_irq(unsigned int irq)
 {
-	unsigned long flags;
-
-	spin_lock_irqsave(&ip32_irq_lock, flags);
 	crime_mask |= 1 << (irq - 1);
 	crime->imask = crime_mask;
-	spin_unlock_irqrestore(&ip32_irq_lock, flags);
-}
-
-static unsigned int startup_crime_irq(unsigned int irq)
-{
-	enable_crime_irq(irq);
-	return 0; /* This is probably not right; we could have pending irqs */
 }
 
 static void disable_crime_irq(unsigned int irq)
 {
-	unsigned long flags;
-
-	spin_lock_irqsave(&ip32_irq_lock, flags);
 	crime_mask &= ~(1 << (irq - 1));
 	crime->imask = crime_mask;
 	flush_crime_bus();
-	spin_unlock_irqrestore(&ip32_irq_lock, flags);
 }
 
 static void mask_and_ack_crime_irq(unsigned int irq)
 {
-	unsigned long flags;
-
 	/* Edge triggered interrupts must be cleared. */
 	if ((irq >= CRIME_GBE0_IRQ && irq <= CRIME_GBE3_IRQ)
 	    || (irq >= CRIME_RE_EMPTY_E_IRQ && irq <= CRIME_RE_IDLE_E_IRQ)
 	    || (irq >= CRIME_SOFT0_IRQ && irq <= CRIME_SOFT2_IRQ)) {
 	        uint64_t crime_int;
-		spin_lock_irqsave(&ip32_irq_lock, flags);
 		crime_int = crime->hard_int;
 		crime_int &= ~(1 << (irq - 1));
 		crime->hard_int = crime_int;
-		spin_unlock_irqrestore(&ip32_irq_lock, flags);
 	}
 	disable_crime_irq(irq);
 }
@@ -226,15 +192,12 @@
 		enable_crime_irq(irq);
 }
 
-#define shutdown_crime_irq disable_crime_irq
-
 static struct irq_chip ip32_crime_interrupt = {
 	.typename = "IP32 CRIME",
-	.startup = startup_crime_irq,
-	.shutdown = shutdown_crime_irq,
-	.enable = enable_crime_irq,
-	.disable = disable_crime_irq,
 	.ack = mask_and_ack_crime_irq,
+	.mask = disable_crime_irq,
+	.mask_ack = mask_and_ack_crime_irq,
+	.unmask = enable_crime_irq,
 	.end = end_crime_irq,
 };
 
@@ -248,34 +211,20 @@
 
 static void enable_macepci_irq(unsigned int irq)
 {
-	unsigned long flags;
-
-	spin_lock_irqsave(&ip32_irq_lock, flags);
 	macepci_mask |= MACEPCI_CONTROL_INT(irq - 9);
 	mace->pci.control = macepci_mask;
 	crime_mask |= 1 << (irq - 1);
 	crime->imask = crime_mask;
-	spin_unlock_irqrestore(&ip32_irq_lock, flags);
-}
-
-static unsigned int startup_macepci_irq(unsigned int irq)
-{
-  	enable_macepci_irq (irq);
-	return 0;
 }
 
 static void disable_macepci_irq(unsigned int irq)
 {
-	unsigned long flags;
-
-	spin_lock_irqsave(&ip32_irq_lock, flags);
 	crime_mask &= ~(1 << (irq - 1));
 	crime->imask = crime_mask;
 	flush_crime_bus();
 	macepci_mask &= ~MACEPCI_CONTROL_INT(irq - 9);
 	mace->pci.control = macepci_mask;
 	flush_mace_bus();
-	spin_unlock_irqrestore(&ip32_irq_lock, flags);
 }
 
 static void end_macepci_irq(unsigned int irq)
@@ -284,16 +233,12 @@
 		enable_macepci_irq(irq);
 }
 
-#define shutdown_macepci_irq disable_macepci_irq
-#define mask_and_ack_macepci_irq disable_macepci_irq
-
 static struct irq_chip ip32_macepci_interrupt = {
 	.typename = "IP32 MACE PCI",
-	.startup = startup_macepci_irq,
-	.shutdown = shutdown_macepci_irq,
-	.enable = enable_macepci_irq,
-	.disable = disable_macepci_irq,
-	.ack = mask_and_ack_macepci_irq,
+	.ack = disable_macepci_irq,
+	.mask = disable_macepci_irq,
+	.mask_ack = disable_macepci_irq,
+	.unmask = enable_macepci_irq,
 	.end = end_macepci_irq,
 };
 
@@ -339,7 +284,6 @@
 static void enable_maceisa_irq (unsigned int irq)
 {
 	unsigned int crime_int = 0;
-	unsigned long flags;
 
 	DBG ("maceisa enable: %u\n", irq);
 
@@ -355,26 +299,16 @@
 		break;
 	}
 	DBG ("crime_int %08x enabled\n", crime_int);
-	spin_lock_irqsave(&ip32_irq_lock, flags);
 	crime_mask |= crime_int;
 	crime->imask = crime_mask;
 	maceisa_mask |= 1 << (irq - 33);
 	mace->perif.ctrl.imask = maceisa_mask;
-	spin_unlock_irqrestore(&ip32_irq_lock, flags);
-}
-
-static unsigned int startup_maceisa_irq(unsigned int irq)
-{
-	enable_maceisa_irq(irq);
-	return 0;
 }
 
 static void disable_maceisa_irq(unsigned int irq)
 {
 	unsigned int crime_int = 0;
-	unsigned long flags;
 
-	spin_lock_irqsave(&ip32_irq_lock, flags);
 	maceisa_mask &= ~(1 << (irq - 33));
         if(!(maceisa_mask & MACEISA_AUDIO_INT))
 		crime_int |= MACE_AUDIO_INT;
@@ -387,23 +321,20 @@
 	flush_crime_bus();
 	mace->perif.ctrl.imask = maceisa_mask;
 	flush_mace_bus();
-	spin_unlock_irqrestore(&ip32_irq_lock, flags);
 }
 
 static void mask_and_ack_maceisa_irq(unsigned int irq)
 {
-	unsigned long mace_int, flags;
+	unsigned long mace_int;
 
 	switch (irq) {
 	case MACEISA_PARALLEL_IRQ:
 	case MACEISA_SERIAL1_TDMAPR_IRQ:
 	case MACEISA_SERIAL2_TDMAPR_IRQ:
 		/* edge triggered */
-		spin_lock_irqsave(&ip32_irq_lock, flags);
 		mace_int = mace->perif.ctrl.istat;
 		mace_int &= ~(1 << (irq - 33));
 		mace->perif.ctrl.istat = mace_int;
-		spin_unlock_irqrestore(&ip32_irq_lock, flags);
 		break;
 	}
 	disable_maceisa_irq(irq);
@@ -415,15 +346,12 @@
 		enable_maceisa_irq(irq);
 }
 
-#define shutdown_maceisa_irq disable_maceisa_irq
-
 static struct irq_chip ip32_maceisa_interrupt = {
 	.typename = "IP32 MACE ISA",
-	.startup = startup_maceisa_irq,
-	.shutdown = shutdown_maceisa_irq,
-	.enable = enable_maceisa_irq,
-	.disable = disable_maceisa_irq,
 	.ack = mask_and_ack_maceisa_irq,
+	.mask = disable_maceisa_irq,
+	.mask_ack = mask_and_ack_maceisa_irq,
+	.unmask = enable_maceisa_irq,
 	.end = end_maceisa_irq,
 };
 
@@ -433,29 +361,15 @@
 
 static void enable_mace_irq(unsigned int irq)
 {
-	unsigned long flags;
-
-	spin_lock_irqsave(&ip32_irq_lock, flags);
 	crime_mask |= 1 << (irq - 1);
 	crime->imask = crime_mask;
-	spin_unlock_irqrestore(&ip32_irq_lock, flags);
-}
-
-static unsigned int startup_mace_irq(unsigned int irq)
-{
-	enable_mace_irq(irq);
-	return 0;
 }
 
 static void disable_mace_irq(unsigned int irq)
 {
-	unsigned long flags;
-
-	spin_lock_irqsave(&ip32_irq_lock, flags);
 	crime_mask &= ~(1 << (irq - 1));
 	crime->imask = crime_mask;
 	flush_crime_bus();
-	spin_unlock_irqrestore(&ip32_irq_lock, flags);
 }
 
 static void end_mace_irq(unsigned int irq)
@@ -464,16 +378,12 @@
 		enable_mace_irq(irq);
 }
 
-#define shutdown_mace_irq disable_mace_irq
-#define mask_and_ack_mace_irq disable_mace_irq
-
 static struct irq_chip ip32_mace_interrupt = {
 	.typename = "IP32 MACE",
-	.startup = startup_mace_irq,
-	.shutdown = shutdown_mace_irq,
-	.enable = enable_mace_irq,
-	.disable = disable_mace_irq,
-	.ack = mask_and_ack_mace_irq,
+	.ack = disable_mace_irq,
+	.mask = disable_mace_irq,
+	.mask_ack = disable_mace_irq,
+	.unmask = enable_mace_irq,
 	.end = end_mace_irq,
 };
 
@@ -586,10 +496,7 @@
 		else
 			controller = &ip32_maceisa_interrupt;
 
-		irq_desc[irq].status = IRQ_DISABLED;
-		irq_desc[irq].action = 0;
-		irq_desc[irq].depth = 0;
-		irq_desc[irq].chip = controller;
+		set_irq_chip(irq, controller);
 	}
 	setup_irq(CRIME_MEMERR_IRQ, &memerr_irq);
 	setup_irq(CRIME_CPUERR_IRQ, &cpuerr_irq);
diff --git a/arch/mips/sibyte/bcm1480/irq.c b/arch/mips/sibyte/bcm1480/irq.c
index 8b1f414..2e8f6b2 100644
--- a/arch/mips/sibyte/bcm1480/irq.c
+++ b/arch/mips/sibyte/bcm1480/irq.c
@@ -45,11 +45,9 @@
  */
 
 
-#define shutdown_bcm1480_irq	disable_bcm1480_irq
 static void end_bcm1480_irq(unsigned int irq);
 static void enable_bcm1480_irq(unsigned int irq);
 static void disable_bcm1480_irq(unsigned int irq);
-static unsigned int startup_bcm1480_irq(unsigned int irq);
 static void ack_bcm1480_irq(unsigned int irq);
 #ifdef CONFIG_SMP
 static void bcm1480_set_affinity(unsigned int irq, cpumask_t mask);
@@ -85,11 +83,10 @@
 
 static struct irq_chip bcm1480_irq_type = {
 	.typename = "BCM1480-IMR",
-	.startup = startup_bcm1480_irq,
-	.shutdown = shutdown_bcm1480_irq,
-	.enable = enable_bcm1480_irq,
-	.disable = disable_bcm1480_irq,
 	.ack = ack_bcm1480_irq,
+	.mask = disable_bcm1480_irq,
+	.mask_ack = ack_bcm1480_irq,
+	.unmask = enable_bcm1480_irq,
 	.end = end_bcm1480_irq,
 #ifdef CONFIG_SMP
 	.set_affinity = bcm1480_set_affinity
@@ -188,14 +185,6 @@
 
 /*****************************************************************************/
 
-static unsigned int startup_bcm1480_irq(unsigned int irq)
-{
-	bcm1480_unmask_irq(bcm1480_irq_owner[irq], irq);
-
-	return 0;		/* never anything pending */
-}
-
-
 static void disable_bcm1480_irq(unsigned int irq)
 {
 	bcm1480_mask_irq(bcm1480_irq_owner[irq], irq);
@@ -270,16 +259,9 @@
 {
 	int i;
 
-	for (i = 0; i < NR_IRQS; i++) {
-		irq_desc[i].status = IRQ_DISABLED;
-		irq_desc[i].action = 0;
-		irq_desc[i].depth = 1;
-		if (i < BCM1480_NR_IRQS) {
-			irq_desc[i].chip = &bcm1480_irq_type;
-			bcm1480_irq_owner[i] = 0;
-		} else {
-			irq_desc[i].chip = &no_irq_chip;
-		}
+	for (i = 0; i < BCM1480_NR_IRQS; i++) {
+		set_irq_chip(i, &bcm1480_irq_type);
+		bcm1480_irq_owner[i] = 0;
 	}
 }
 
diff --git a/arch/mips/sibyte/bcm1480/time.c b/arch/mips/sibyte/bcm1480/time.c
index e136bde..6f3f71b 100644
--- a/arch/mips/sibyte/bcm1480/time.c
+++ b/arch/mips/sibyte/bcm1480/time.c
@@ -94,8 +94,6 @@
 	 */
 }
 
-#include <asm/sibyte/sb1250.h>
-
 void bcm1480_timer_interrupt(void)
 {
 	int cpu = smp_processor_id();
@@ -119,7 +117,7 @@
 	}
 }
 
-static unsigned int bcm1480_hpt_read(void)
+static cycle_t bcm1480_hpt_read(void)
 {
 	/* We assume this function is called xtime_lock held. */
 	unsigned long count =
@@ -129,6 +127,6 @@
 
 void __init bcm1480_hpt_setup(void)
 {
-	mips_hpt_read = bcm1480_hpt_read;
+	clocksource_mips.read = bcm1480_hpt_read;
 	mips_hpt_frequency = BCM1480_HPT_VALUE;
 }
diff --git a/arch/mips/sibyte/sb1250/irq.c b/arch/mips/sibyte/sb1250/irq.c
index d5d2677..82ce753 100644
--- a/arch/mips/sibyte/sb1250/irq.c
+++ b/arch/mips/sibyte/sb1250/irq.c
@@ -44,11 +44,9 @@
  */
 
 
-#define shutdown_sb1250_irq	disable_sb1250_irq
 static void end_sb1250_irq(unsigned int irq);
 static void enable_sb1250_irq(unsigned int irq);
 static void disable_sb1250_irq(unsigned int irq);
-static unsigned int startup_sb1250_irq(unsigned int irq);
 static void ack_sb1250_irq(unsigned int irq);
 #ifdef CONFIG_SMP
 static void sb1250_set_affinity(unsigned int irq, cpumask_t mask);
@@ -70,11 +68,10 @@
 
 static struct irq_chip sb1250_irq_type = {
 	.typename = "SB1250-IMR",
-	.startup = startup_sb1250_irq,
-	.shutdown = shutdown_sb1250_irq,
-	.enable = enable_sb1250_irq,
-	.disable = disable_sb1250_irq,
 	.ack = ack_sb1250_irq,
+	.mask = disable_sb1250_irq,
+	.mask_ack = ack_sb1250_irq,
+	.unmask = enable_sb1250_irq,
 	.end = end_sb1250_irq,
 #ifdef CONFIG_SMP
 	.set_affinity = sb1250_set_affinity
@@ -163,14 +160,6 @@
 
 /*****************************************************************************/
 
-static unsigned int startup_sb1250_irq(unsigned int irq)
-{
-	sb1250_unmask_irq(sb1250_irq_owner[irq], irq);
-
-	return 0;		/* never anything pending */
-}
-
-
 static void disable_sb1250_irq(unsigned int irq)
 {
 	sb1250_mask_irq(sb1250_irq_owner[irq], irq);
@@ -239,16 +228,9 @@
 {
 	int i;
 
-	for (i = 0; i < NR_IRQS; i++) {
-		irq_desc[i].status = IRQ_DISABLED;
-		irq_desc[i].action = 0;
-		irq_desc[i].depth = 1;
-		if (i < SB1250_NR_IRQS) {
-			irq_desc[i].chip = &sb1250_irq_type;
-			sb1250_irq_owner[i] = 0;
-		} else {
-			irq_desc[i].chip = &no_irq_chip;
-		}
+	for (i = 0; i < SB1250_NR_IRQS; i++) {
+		set_irq_chip(i, &sb1250_irq_type);
+		sb1250_irq_owner[i] = 0;
 	}
 }
 
diff --git a/arch/mips/sibyte/sb1250/time.c b/arch/mips/sibyte/sb1250/time.c
index bcb74f2..2efffe1 100644
--- a/arch/mips/sibyte/sb1250/time.c
+++ b/arch/mips/sibyte/sb1250/time.c
@@ -51,7 +51,7 @@
 
 extern int sb1250_steal_irq(int irq);
 
-static unsigned int sb1250_hpt_read(void);
+static cycle_t sb1250_hpt_read(void);
 
 void __init sb1250_hpt_setup(void)
 {
@@ -66,8 +66,8 @@
 			     IOADDR(A_SCD_TIMER_REGISTER(SB1250_HPT_NUM, R_SCD_TIMER_CFG)));
 
 		mips_hpt_frequency = V_SCD_TIMER_FREQ;
-		mips_hpt_read = sb1250_hpt_read;
-		mips_hpt_mask = M_SCD_TIMER_INIT;
+		clocksource_mips.read = sb1250_hpt_read;
+		clocksource_mips.mask = M_SCD_TIMER_INIT;
 	}
 }
 
@@ -143,7 +143,7 @@
  * The HPT is free running from SB1250_HPT_VALUE down to 0 then starts over
  * again.
  */
-static unsigned int sb1250_hpt_read(void)
+static cycle_t sb1250_hpt_read(void)
 {
 	unsigned int count;
 
diff --git a/arch/mips/sni/irq.c b/arch/mips/sni/irq.c
index 48fb74a..8511bcc 100644
--- a/arch/mips/sni/irq.c
+++ b/arch/mips/sni/irq.c
@@ -11,44 +11,25 @@
 #include <linux/interrupt.h>
 #include <linux/irq.h>
 #include <linux/kernel.h>
-#include <linux/spinlock.h>
 
 #include <asm/i8259.h>
 #include <asm/io.h>
 #include <asm/sni.h>
 
-DEFINE_SPINLOCK(pciasic_lock);
-
 static void enable_pciasic_irq(unsigned int irq)
 {
 	unsigned int mask = 1 << (irq - PCIMT_IRQ_INT2);
-	unsigned long flags;
 
-	spin_lock_irqsave(&pciasic_lock, flags);
 	*(volatile u8 *) PCIMT_IRQSEL |= mask;
-	spin_unlock_irqrestore(&pciasic_lock, flags);
 }
 
-static unsigned int startup_pciasic_irq(unsigned int irq)
-{
-	enable_pciasic_irq(irq);
-	return 0; /* never anything pending */
-}
-
-#define shutdown_pciasic_irq	disable_pciasic_irq
-
 void disable_pciasic_irq(unsigned int irq)
 {
 	unsigned int mask = ~(1 << (irq - PCIMT_IRQ_INT2));
-	unsigned long flags;
 
-	spin_lock_irqsave(&pciasic_lock, flags);
 	*(volatile u8 *) PCIMT_IRQSEL &= mask;
-	spin_unlock_irqrestore(&pciasic_lock, flags);
 }
 
-#define mask_and_ack_pciasic_irq disable_pciasic_irq
-
 static void end_pciasic_irq(unsigned int irq)
 {
 	if (!(irq_desc[irq].status & (IRQ_DISABLED|IRQ_INPROGRESS)))
@@ -57,11 +38,10 @@
 
 static struct irq_chip pciasic_irq_type = {
 	.typename = "ASIC-PCI",
-	.startup = startup_pciasic_irq,
-	.shutdown = shutdown_pciasic_irq,
-	.enable = enable_pciasic_irq,
-	.disable = disable_pciasic_irq,
-	.ack = mask_and_ack_pciasic_irq,
+	.ack = disable_pciasic_irq,
+	.mask = disable_pciasic_irq,
+	.mask_ack = disable_pciasic_irq,
+	.unmask = enable_pciasic_irq,
 	.end = end_pciasic_irq,
 };
 
@@ -178,12 +158,8 @@
 
 void __init init_pciasic(void)
 {
-	unsigned long flags;
-
-	spin_lock_irqsave(&pciasic_lock, flags);
 	* (volatile u8 *) PCIMT_IRQSEL =
 		IT_EISA | IT_INTA | IT_INTB | IT_INTC | IT_INTD;
-	spin_unlock_irqrestore(&pciasic_lock, flags);
 }
 
 /*
@@ -199,12 +175,8 @@
 	init_pciasic();
 
 	/* Actually we've got more interrupts to handle ...  */
-	for (i = PCIMT_IRQ_INT2; i <= PCIMT_IRQ_ETHERNET; i++) {
-		irq_desc[i].status     = IRQ_DISABLED;
-		irq_desc[i].action     = 0;
-		irq_desc[i].depth      = 1;
-		irq_desc[i].chip    = &pciasic_irq_type;
-	}
+	for (i = PCIMT_IRQ_INT2; i <= PCIMT_IRQ_ETHERNET; i++)
+		set_irq_chip(i, &pciasic_irq_type);
 
 	change_c0_status(ST0_IM, IE_IRQ1|IE_IRQ2|IE_IRQ3|IE_IRQ4);
 }
diff --git a/arch/mips/tx4927/common/tx4927_irq.c b/arch/mips/tx4927/common/tx4927_irq.c
index 8266a88..21873de 100644
--- a/arch/mips/tx4927/common/tx4927_irq.c
+++ b/arch/mips/tx4927/common/tx4927_irq.c
@@ -64,19 +64,13 @@
 #define TX4927_IRQ_NEST4       ( 1 <<  9 )
 
 #define TX4927_IRQ_CP0_INIT     ( 1 << 10 )
-#define TX4927_IRQ_CP0_STARTUP  ( 1 << 11 )
-#define TX4927_IRQ_CP0_SHUTDOWN ( 1 << 12 )
 #define TX4927_IRQ_CP0_ENABLE   ( 1 << 13 )
 #define TX4927_IRQ_CP0_DISABLE  ( 1 << 14 )
-#define TX4927_IRQ_CP0_MASK     ( 1 << 15 )
 #define TX4927_IRQ_CP0_ENDIRQ   ( 1 << 16 )
 
 #define TX4927_IRQ_PIC_INIT     ( 1 << 20 )
-#define TX4927_IRQ_PIC_STARTUP  ( 1 << 21 )
-#define TX4927_IRQ_PIC_SHUTDOWN ( 1 << 22 )
 #define TX4927_IRQ_PIC_ENABLE   ( 1 << 23 )
 #define TX4927_IRQ_PIC_DISABLE  ( 1 << 24 )
-#define TX4927_IRQ_PIC_MASK     ( 1 << 25 )
 #define TX4927_IRQ_PIC_ENDIRQ   ( 1 << 26 )
 
 #define TX4927_IRQ_ALL         0xffffffff
@@ -87,18 +81,12 @@
 					  | TX4927_IRQ_INFO
 					  | TX4927_IRQ_WARN | TX4927_IRQ_EROR
 //                                       | TX4927_IRQ_CP0_INIT
-//                                       | TX4927_IRQ_CP0_STARTUP
-//                                       | TX4927_IRQ_CP0_SHUTDOWN
 //                                       | TX4927_IRQ_CP0_ENABLE
 //                                       | TX4927_IRQ_CP0_DISABLE
-//                                       | TX4927_IRQ_CP0_MASK
 //                                       | TX4927_IRQ_CP0_ENDIRQ
 //                                       | TX4927_IRQ_PIC_INIT
-//                                       | TX4927_IRQ_PIC_STARTUP
-//                                       | TX4927_IRQ_PIC_SHUTDOWN
 //                                       | TX4927_IRQ_PIC_ENABLE
 //                                       | TX4927_IRQ_PIC_DISABLE
-//                                       | TX4927_IRQ_PIC_MASK
 //                                       | TX4927_IRQ_PIC_ENDIRQ
 //                                       | TX4927_IRQ_INIT
 //                                       | TX4927_IRQ_NEST1
@@ -124,49 +112,36 @@
  * Forwad definitions for all pic's
  */
 
-static unsigned int tx4927_irq_cp0_startup(unsigned int irq);
-static void tx4927_irq_cp0_shutdown(unsigned int irq);
 static void tx4927_irq_cp0_enable(unsigned int irq);
 static void tx4927_irq_cp0_disable(unsigned int irq);
-static void tx4927_irq_cp0_mask_and_ack(unsigned int irq);
 static void tx4927_irq_cp0_end(unsigned int irq);
 
-static unsigned int tx4927_irq_pic_startup(unsigned int irq);
-static void tx4927_irq_pic_shutdown(unsigned int irq);
 static void tx4927_irq_pic_enable(unsigned int irq);
 static void tx4927_irq_pic_disable(unsigned int irq);
-static void tx4927_irq_pic_mask_and_ack(unsigned int irq);
 static void tx4927_irq_pic_end(unsigned int irq);
 
 /*
  * Kernel structs for all pic's
  */
 
-static DEFINE_SPINLOCK(tx4927_cp0_lock);
-static DEFINE_SPINLOCK(tx4927_pic_lock);
-
 #define TX4927_CP0_NAME "TX4927-CP0"
 static struct irq_chip tx4927_irq_cp0_type = {
 	.typename	= TX4927_CP0_NAME,
-	.startup	= tx4927_irq_cp0_startup,
-	.shutdown	= tx4927_irq_cp0_shutdown,
-	.enable		= tx4927_irq_cp0_enable,
-	.disable	= tx4927_irq_cp0_disable,
-	.ack		= tx4927_irq_cp0_mask_and_ack,
+	.ack		= tx4927_irq_cp0_disable,
+	.mask		= tx4927_irq_cp0_disable,
+	.mask_ack	= tx4927_irq_cp0_disable,
+	.unmask		= tx4927_irq_cp0_enable,
 	.end		= tx4927_irq_cp0_end,
-	.set_affinity	= NULL
 };
 
 #define TX4927_PIC_NAME "TX4927-PIC"
 static struct irq_chip tx4927_irq_pic_type = {
 	.typename	= TX4927_PIC_NAME,
-	.startup	= tx4927_irq_pic_startup,
-	.shutdown	= tx4927_irq_pic_shutdown,
-	.enable		= tx4927_irq_pic_enable,
-	.disable	= tx4927_irq_pic_disable,
-	.ack		= tx4927_irq_pic_mask_and_ack,
+	.ack		= tx4927_irq_pic_disable,
+	.mask		= tx4927_irq_pic_disable,
+	.mask_ack	= tx4927_irq_pic_disable,
+	.unmask		= tx4927_irq_pic_enable,
 	.end		= tx4927_irq_pic_end,
-	.set_affinity	= NULL
 };
 
 #define TX4927_PIC_ACTION(s) { no_action, 0, CPU_MASK_NONE, s, NULL, NULL }
@@ -211,8 +186,6 @@
 			break;
 		}
 	}
-
-	return;
 }
 
 static void __init tx4927_irq_cp0_init(void)
@@ -222,71 +195,23 @@
 	TX4927_IRQ_DPRINTK(TX4927_IRQ_CP0_INIT, "beg=%d end=%d\n",
 			   TX4927_IRQ_CP0_BEG, TX4927_IRQ_CP0_END);
 
-	for (i = TX4927_IRQ_CP0_BEG; i <= TX4927_IRQ_CP0_END; i++) {
-		irq_desc[i].status = IRQ_DISABLED;
-		irq_desc[i].action = 0;
-		irq_desc[i].depth = 1;
-		irq_desc[i].chip = &tx4927_irq_cp0_type;
-	}
-
-	return;
-}
-
-static unsigned int tx4927_irq_cp0_startup(unsigned int irq)
-{
-	TX4927_IRQ_DPRINTK(TX4927_IRQ_CP0_STARTUP, "irq=%d \n", irq);
-
-	tx4927_irq_cp0_enable(irq);
-
-	return (0);
-}
-
-static void tx4927_irq_cp0_shutdown(unsigned int irq)
-{
-	TX4927_IRQ_DPRINTK(TX4927_IRQ_CP0_SHUTDOWN, "irq=%d \n", irq);
-
-	tx4927_irq_cp0_disable(irq);
-
-	return;
+	for (i = TX4927_IRQ_CP0_BEG; i <= TX4927_IRQ_CP0_END; i++)
+		set_irq_chip_and_handler(i, &tx4927_irq_cp0_type,
+					 handle_level_irq);
 }
 
 static void tx4927_irq_cp0_enable(unsigned int irq)
 {
-	unsigned long flags;
-
 	TX4927_IRQ_DPRINTK(TX4927_IRQ_CP0_ENABLE, "irq=%d \n", irq);
 
-	spin_lock_irqsave(&tx4927_cp0_lock, flags);
-
 	tx4927_irq_cp0_modify(CCP0_STATUS, 0, tx4927_irq_cp0_mask(irq));
-
-	spin_unlock_irqrestore(&tx4927_cp0_lock, flags);
-
-	return;
 }
 
 static void tx4927_irq_cp0_disable(unsigned int irq)
 {
-	unsigned long flags;
-
 	TX4927_IRQ_DPRINTK(TX4927_IRQ_CP0_DISABLE, "irq=%d \n", irq);
 
-	spin_lock_irqsave(&tx4927_cp0_lock, flags);
-
 	tx4927_irq_cp0_modify(CCP0_STATUS, tx4927_irq_cp0_mask(irq), 0);
-
-	spin_unlock_irqrestore(&tx4927_cp0_lock, flags);
-
-	return;
-}
-
-static void tx4927_irq_cp0_mask_and_ack(unsigned int irq)
-{
-	TX4927_IRQ_DPRINTK(TX4927_IRQ_CP0_MASK, "irq=%d \n", irq);
-
-	tx4927_irq_cp0_disable(irq);
-
-	return;
 }
 
 static void tx4927_irq_cp0_end(unsigned int irq)
@@ -296,8 +221,6 @@
 	if (!(irq_desc[irq].status & (IRQ_DISABLED | IRQ_INPROGRESS))) {
 		tx4927_irq_cp0_enable(irq);
 	}
-
-	return;
 }
 
 /*
@@ -418,94 +341,39 @@
 	val &= (~clr_bits);
 	val |= (set_bits);
 	TX4927_WR(pic_reg, val);
-
-	return;
 }
 
 static void __init tx4927_irq_pic_init(void)
 {
-	unsigned long flags;
 	int i;
 
 	TX4927_IRQ_DPRINTK(TX4927_IRQ_PIC_INIT, "beg=%d end=%d\n",
 			   TX4927_IRQ_PIC_BEG, TX4927_IRQ_PIC_END);
 
-	for (i = TX4927_IRQ_PIC_BEG; i <= TX4927_IRQ_PIC_END; i++) {
-		irq_desc[i].status = IRQ_DISABLED;
-		irq_desc[i].action = 0;
-		irq_desc[i].depth = 2;
-		irq_desc[i].chip = &tx4927_irq_pic_type;
-	}
+	for (i = TX4927_IRQ_PIC_BEG; i <= TX4927_IRQ_PIC_END; i++)
+		set_irq_chip_and_handler(i, &tx4927_irq_pic_type,
+					 handle_level_irq);
 
 	setup_irq(TX4927_IRQ_NEST_PIC_ON_CP0, &tx4927_irq_pic_action);
 
-	spin_lock_irqsave(&tx4927_pic_lock, flags);
-
 	TX4927_WR(0xff1ff640, 0x6);	/* irq level mask -- only accept hightest */
 	TX4927_WR(0xff1ff600, TX4927_RD(0xff1ff600) | 0x1);	/* irq enable */
-
-	spin_unlock_irqrestore(&tx4927_pic_lock, flags);
-
-	return;
-}
-
-static unsigned int tx4927_irq_pic_startup(unsigned int irq)
-{
-	TX4927_IRQ_DPRINTK(TX4927_IRQ_PIC_STARTUP, "irq=%d\n", irq);
-
-	tx4927_irq_pic_enable(irq);
-
-	return (0);
-}
-
-static void tx4927_irq_pic_shutdown(unsigned int irq)
-{
-	TX4927_IRQ_DPRINTK(TX4927_IRQ_PIC_SHUTDOWN, "irq=%d\n", irq);
-
-	tx4927_irq_pic_disable(irq);
-
-	return;
 }
 
 static void tx4927_irq_pic_enable(unsigned int irq)
 {
-	unsigned long flags;
-
 	TX4927_IRQ_DPRINTK(TX4927_IRQ_PIC_ENABLE, "irq=%d\n", irq);
 
-	spin_lock_irqsave(&tx4927_pic_lock, flags);
-
 	tx4927_irq_pic_modify(tx4927_irq_pic_addr(irq), 0,
 			      tx4927_irq_pic_mask(irq));
-
-	spin_unlock_irqrestore(&tx4927_pic_lock, flags);
-
-	return;
 }
 
 static void tx4927_irq_pic_disable(unsigned int irq)
 {
-	unsigned long flags;
-
 	TX4927_IRQ_DPRINTK(TX4927_IRQ_PIC_DISABLE, "irq=%d\n", irq);
 
-	spin_lock_irqsave(&tx4927_pic_lock, flags);
-
 	tx4927_irq_pic_modify(tx4927_irq_pic_addr(irq),
 			      tx4927_irq_pic_mask(irq), 0);
-
-	spin_unlock_irqrestore(&tx4927_pic_lock, flags);
-
-	return;
-}
-
-static void tx4927_irq_pic_mask_and_ack(unsigned int irq)
-{
-	TX4927_IRQ_DPRINTK(TX4927_IRQ_PIC_MASK, "irq=%d\n", irq);
-
-	tx4927_irq_pic_disable(irq);
-
-	return;
 }
 
 static void tx4927_irq_pic_end(unsigned int irq)
@@ -515,8 +383,6 @@
 	if (!(irq_desc[irq].status & (IRQ_DISABLED | IRQ_INPROGRESS))) {
 		tx4927_irq_pic_enable(irq);
 	}
-
-	return;
 }
 
 /*
@@ -533,8 +399,6 @@
 	tx4927_irq_pic_init();
 
 	TX4927_IRQ_DPRINTK(TX4927_IRQ_INIT, "+\n");
-
-	return;
 }
 
 static int tx4927_irq_nested(void)
diff --git a/arch/mips/tx4927/toshiba_rbtx4927/toshiba_rbtx4927_irq.c b/arch/mips/tx4927/toshiba_rbtx4927/toshiba_rbtx4927_irq.c
index 0c3c3f6..34cdb2a 100644
--- a/arch/mips/tx4927/toshiba_rbtx4927/toshiba_rbtx4927_irq.c
+++ b/arch/mips/tx4927/toshiba_rbtx4927/toshiba_rbtx4927_irq.c
@@ -151,16 +151,11 @@
 #define TOSHIBA_RBTX4927_IRQ_EROR          ( 1 <<  2 )
 
 #define TOSHIBA_RBTX4927_IRQ_IOC_INIT      ( 1 << 10 )
-#define TOSHIBA_RBTX4927_IRQ_IOC_STARTUP   ( 1 << 11 )
-#define TOSHIBA_RBTX4927_IRQ_IOC_SHUTDOWN  ( 1 << 12 )
 #define TOSHIBA_RBTX4927_IRQ_IOC_ENABLE    ( 1 << 13 )
 #define TOSHIBA_RBTX4927_IRQ_IOC_DISABLE   ( 1 << 14 )
-#define TOSHIBA_RBTX4927_IRQ_IOC_MASK      ( 1 << 15 )
 #define TOSHIBA_RBTX4927_IRQ_IOC_ENDIRQ    ( 1 << 16 )
 
 #define TOSHIBA_RBTX4927_IRQ_ISA_INIT      ( 1 << 20 )
-#define TOSHIBA_RBTX4927_IRQ_ISA_STARTUP   ( 1 << 21 )
-#define TOSHIBA_RBTX4927_IRQ_ISA_SHUTDOWN  ( 1 << 22 )
 #define TOSHIBA_RBTX4927_IRQ_ISA_ENABLE    ( 1 << 23 )
 #define TOSHIBA_RBTX4927_IRQ_ISA_DISABLE   ( 1 << 24 )
 #define TOSHIBA_RBTX4927_IRQ_ISA_MASK      ( 1 << 25 )
@@ -175,15 +170,10 @@
     (TOSHIBA_RBTX4927_IRQ_NONE | TOSHIBA_RBTX4927_IRQ_INFO |
      TOSHIBA_RBTX4927_IRQ_WARN | TOSHIBA_RBTX4927_IRQ_EROR
 //                                                 | TOSHIBA_RBTX4927_IRQ_IOC_INIT
-//                                                 | TOSHIBA_RBTX4927_IRQ_IOC_STARTUP
-//                                                 | TOSHIBA_RBTX4927_IRQ_IOC_SHUTDOWN
 //                                                 | TOSHIBA_RBTX4927_IRQ_IOC_ENABLE
 //                                                 | TOSHIBA_RBTX4927_IRQ_IOC_DISABLE
-//                                                 | TOSHIBA_RBTX4927_IRQ_IOC_MASK
 //                                                 | TOSHIBA_RBTX4927_IRQ_IOC_ENDIRQ
 //                                                 | TOSHIBA_RBTX4927_IRQ_ISA_INIT
-//                                                 | TOSHIBA_RBTX4927_IRQ_ISA_STARTUP
-//                                                 | TOSHIBA_RBTX4927_IRQ_ISA_SHUTDOWN
 //                                                 | TOSHIBA_RBTX4927_IRQ_ISA_ENABLE
 //                                                 | TOSHIBA_RBTX4927_IRQ_ISA_DISABLE
 //                                                 | TOSHIBA_RBTX4927_IRQ_ISA_MASK
@@ -231,35 +221,25 @@
 extern void mask_and_ack_8259A(unsigned int irq);
 #endif
 
-static unsigned int toshiba_rbtx4927_irq_ioc_startup(unsigned int irq);
-static void toshiba_rbtx4927_irq_ioc_shutdown(unsigned int irq);
 static void toshiba_rbtx4927_irq_ioc_enable(unsigned int irq);
 static void toshiba_rbtx4927_irq_ioc_disable(unsigned int irq);
-static void toshiba_rbtx4927_irq_ioc_mask_and_ack(unsigned int irq);
 static void toshiba_rbtx4927_irq_ioc_end(unsigned int irq);
 
 #ifdef CONFIG_TOSHIBA_FPCIB0
-static unsigned int toshiba_rbtx4927_irq_isa_startup(unsigned int irq);
-static void toshiba_rbtx4927_irq_isa_shutdown(unsigned int irq);
 static void toshiba_rbtx4927_irq_isa_enable(unsigned int irq);
 static void toshiba_rbtx4927_irq_isa_disable(unsigned int irq);
 static void toshiba_rbtx4927_irq_isa_mask_and_ack(unsigned int irq);
 static void toshiba_rbtx4927_irq_isa_end(unsigned int irq);
 #endif
 
-static DEFINE_SPINLOCK(toshiba_rbtx4927_ioc_lock);
-
-
 #define TOSHIBA_RBTX4927_IOC_NAME "RBTX4927-IOC"
 static struct irq_chip toshiba_rbtx4927_irq_ioc_type = {
 	.typename = TOSHIBA_RBTX4927_IOC_NAME,
-	.startup = toshiba_rbtx4927_irq_ioc_startup,
-	.shutdown = toshiba_rbtx4927_irq_ioc_shutdown,
-	.enable = toshiba_rbtx4927_irq_ioc_enable,
-	.disable = toshiba_rbtx4927_irq_ioc_disable,
-	.ack = toshiba_rbtx4927_irq_ioc_mask_and_ack,
+	.ack = toshiba_rbtx4927_irq_ioc_disable,
+	.mask = toshiba_rbtx4927_irq_ioc_disable,
+	.mask_ack = toshiba_rbtx4927_irq_ioc_disable,
+	.unmask = toshiba_rbtx4927_irq_ioc_enable,
 	.end = toshiba_rbtx4927_irq_ioc_end,
-	.set_affinity = NULL
 };
 #define TOSHIBA_RBTX4927_IOC_INTR_ENAB 0xbc002000
 #define TOSHIBA_RBTX4927_IOC_INTR_STAT 0xbc002006
@@ -269,13 +249,11 @@
 #define TOSHIBA_RBTX4927_ISA_NAME "RBTX4927-ISA"
 static struct irq_chip toshiba_rbtx4927_irq_isa_type = {
 	.typename = TOSHIBA_RBTX4927_ISA_NAME,
-	.startup = toshiba_rbtx4927_irq_isa_startup,
-	.shutdown = toshiba_rbtx4927_irq_isa_shutdown,
-	.enable = toshiba_rbtx4927_irq_isa_enable,
-	.disable = toshiba_rbtx4927_irq_isa_disable,
 	.ack = toshiba_rbtx4927_irq_isa_mask_and_ack,
+	.mask = toshiba_rbtx4927_irq_isa_disable,
+	.mask_ack = toshiba_rbtx4927_irq_isa_mask_and_ack,
+	.unmask = toshiba_rbtx4927_irq_isa_enable,
 	.end = toshiba_rbtx4927_irq_isa_end,
-	.set_affinity = NULL
 };
 #endif
 
@@ -363,58 +341,16 @@
 				     TOSHIBA_RBTX4927_IRQ_IOC_END);
 
 	for (i = TOSHIBA_RBTX4927_IRQ_IOC_BEG;
-	     i <= TOSHIBA_RBTX4927_IRQ_IOC_END; i++) {
-		irq_desc[i].status = IRQ_DISABLED;
-		irq_desc[i].action = 0;
-		irq_desc[i].depth = 3;
-		irq_desc[i].chip = &toshiba_rbtx4927_irq_ioc_type;
-	}
+	     i <= TOSHIBA_RBTX4927_IRQ_IOC_END; i++)
+		set_irq_chip_and_handler(i, &toshiba_rbtx4927_irq_ioc_type,
+					 handle_level_irq);
 
 	setup_irq(TOSHIBA_RBTX4927_IRQ_NEST_IOC_ON_PIC,
 		  &toshiba_rbtx4927_irq_ioc_action);
-
-	return;
 }
 
-static unsigned int toshiba_rbtx4927_irq_ioc_startup(unsigned int irq)
-{
-	TOSHIBA_RBTX4927_IRQ_DPRINTK(TOSHIBA_RBTX4927_IRQ_IOC_STARTUP,
-				     "irq=%d\n", irq);
-
-	if (irq < TOSHIBA_RBTX4927_IRQ_IOC_BEG
-	    || irq > TOSHIBA_RBTX4927_IRQ_IOC_END) {
-		TOSHIBA_RBTX4927_IRQ_DPRINTK(TOSHIBA_RBTX4927_IRQ_EROR,
-					     "bad irq=%d\n", irq);
-		panic("\n");
-	}
-
-	toshiba_rbtx4927_irq_ioc_enable(irq);
-
-	return (0);
-}
-
-
-static void toshiba_rbtx4927_irq_ioc_shutdown(unsigned int irq)
-{
-	TOSHIBA_RBTX4927_IRQ_DPRINTK(TOSHIBA_RBTX4927_IRQ_IOC_SHUTDOWN,
-				     "irq=%d\n", irq);
-
-	if (irq < TOSHIBA_RBTX4927_IRQ_IOC_BEG
-	    || irq > TOSHIBA_RBTX4927_IRQ_IOC_END) {
-		TOSHIBA_RBTX4927_IRQ_DPRINTK(TOSHIBA_RBTX4927_IRQ_EROR,
-					     "bad irq=%d\n", irq);
-		panic("\n");
-	}
-
-	toshiba_rbtx4927_irq_ioc_disable(irq);
-
-	return;
-}
-
-
 static void toshiba_rbtx4927_irq_ioc_enable(unsigned int irq)
 {
-	unsigned long flags;
 	volatile unsigned char v;
 
 	TOSHIBA_RBTX4927_IRQ_DPRINTK(TOSHIBA_RBTX4927_IRQ_IOC_ENABLE,
@@ -427,21 +363,14 @@
 		panic("\n");
 	}
 
-	spin_lock_irqsave(&toshiba_rbtx4927_ioc_lock, flags);
-
 	v = TX4927_RD08(TOSHIBA_RBTX4927_IOC_INTR_ENAB);
 	v |= (1 << (irq - TOSHIBA_RBTX4927_IRQ_IOC_BEG));
 	TOSHIBA_RBTX4927_WR08(TOSHIBA_RBTX4927_IOC_INTR_ENAB, v);
-
-	spin_unlock_irqrestore(&toshiba_rbtx4927_ioc_lock, flags);
-
-	return;
 }
 
 
 static void toshiba_rbtx4927_irq_ioc_disable(unsigned int irq)
 {
-	unsigned long flags;
 	volatile unsigned char v;
 
 	TOSHIBA_RBTX4927_IRQ_DPRINTK(TOSHIBA_RBTX4927_IRQ_IOC_DISABLE,
@@ -454,36 +383,11 @@
 		panic("\n");
 	}
 
-	spin_lock_irqsave(&toshiba_rbtx4927_ioc_lock, flags);
-
 	v = TX4927_RD08(TOSHIBA_RBTX4927_IOC_INTR_ENAB);
 	v &= ~(1 << (irq - TOSHIBA_RBTX4927_IRQ_IOC_BEG));
 	TOSHIBA_RBTX4927_WR08(TOSHIBA_RBTX4927_IOC_INTR_ENAB, v);
-
-	spin_unlock_irqrestore(&toshiba_rbtx4927_ioc_lock, flags);
-
-	return;
 }
 
-
-static void toshiba_rbtx4927_irq_ioc_mask_and_ack(unsigned int irq)
-{
-	TOSHIBA_RBTX4927_IRQ_DPRINTK(TOSHIBA_RBTX4927_IRQ_IOC_MASK,
-				     "irq=%d\n", irq);
-
-	if (irq < TOSHIBA_RBTX4927_IRQ_IOC_BEG
-	    || irq > TOSHIBA_RBTX4927_IRQ_IOC_END) {
-		TOSHIBA_RBTX4927_IRQ_DPRINTK(TOSHIBA_RBTX4927_IRQ_EROR,
-					     "bad irq=%d\n", irq);
-		panic("\n");
-	}
-
-	toshiba_rbtx4927_irq_ioc_disable(irq);
-
-	return;
-}
-
-
 static void toshiba_rbtx4927_irq_ioc_end(unsigned int irq)
 {
 	TOSHIBA_RBTX4927_IRQ_DPRINTK(TOSHIBA_RBTX4927_IRQ_IOC_ENDIRQ,
@@ -499,8 +403,6 @@
 	if (!(irq_desc[irq].status & (IRQ_DISABLED | IRQ_INPROGRESS))) {
 		toshiba_rbtx4927_irq_ioc_enable(irq);
 	}
-
-	return;
 }
 
 
@@ -520,13 +422,8 @@
 				     TOSHIBA_RBTX4927_IRQ_ISA_END);
 
 	for (i = TOSHIBA_RBTX4927_IRQ_ISA_BEG;
-	     i <= TOSHIBA_RBTX4927_IRQ_ISA_END; i++) {
-		irq_desc[i].status = IRQ_DISABLED;
-		irq_desc[i].action = 0;
-		irq_desc[i].depth =
-		    ((i < TOSHIBA_RBTX4927_IRQ_ISA_MID) ? (4) : (5));
-		irq_desc[i].chip = &toshiba_rbtx4927_irq_isa_type;
-	}
+	     i <= TOSHIBA_RBTX4927_IRQ_ISA_END; i++)
+		set_irq_chip(i, &toshiba_rbtx4927_irq_isa_type);
 
 	setup_irq(TOSHIBA_RBTX4927_IRQ_NEST_ISA_ON_IOC,
 		  &toshiba_rbtx4927_irq_isa_master);
@@ -536,48 +433,6 @@
 	/* make sure we are looking at IRR (not ISR) */
 	outb(0x0A, 0x20);
 	outb(0x0A, 0xA0);
-
-	return;
-}
-#endif
-
-
-#ifdef CONFIG_TOSHIBA_FPCIB0
-static unsigned int toshiba_rbtx4927_irq_isa_startup(unsigned int irq)
-{
-	TOSHIBA_RBTX4927_IRQ_DPRINTK(TOSHIBA_RBTX4927_IRQ_ISA_STARTUP,
-				     "irq=%d\n", irq);
-
-	if (irq < TOSHIBA_RBTX4927_IRQ_ISA_BEG
-	    || irq > TOSHIBA_RBTX4927_IRQ_ISA_END) {
-		TOSHIBA_RBTX4927_IRQ_DPRINTK(TOSHIBA_RBTX4927_IRQ_EROR,
-					     "bad irq=%d\n", irq);
-		panic("\n");
-	}
-
-	toshiba_rbtx4927_irq_isa_enable(irq);
-
-	return (0);
-}
-#endif
-
-
-#ifdef CONFIG_TOSHIBA_FPCIB0
-static void toshiba_rbtx4927_irq_isa_shutdown(unsigned int irq)
-{
-	TOSHIBA_RBTX4927_IRQ_DPRINTK(TOSHIBA_RBTX4927_IRQ_ISA_SHUTDOWN,
-				     "irq=%d\n", irq);
-
-	if (irq < TOSHIBA_RBTX4927_IRQ_ISA_BEG
-	    || irq > TOSHIBA_RBTX4927_IRQ_ISA_END) {
-		TOSHIBA_RBTX4927_IRQ_DPRINTK(TOSHIBA_RBTX4927_IRQ_EROR,
-					     "bad irq=%d\n", irq);
-		panic("\n");
-	}
-
-	toshiba_rbtx4927_irq_isa_disable(irq);
-
-	return;
 }
 #endif
 
@@ -596,8 +451,6 @@
 	}
 
 	enable_8259A_irq(irq);
-
-	return;
 }
 #endif
 
@@ -616,8 +469,6 @@
 	}
 
 	disable_8259A_irq(irq);
-
-	return;
 }
 #endif
 
@@ -636,8 +487,6 @@
 	}
 
 	mask_and_ack_8259A(irq);
-
-	return;
 }
 #endif
 
@@ -658,8 +507,6 @@
 	if (!(irq_desc[irq].status & (IRQ_DISABLED | IRQ_INPROGRESS))) {
 		toshiba_rbtx4927_irq_isa_enable(irq);
 	}
-
-	return;
 }
 #endif
 
@@ -668,8 +515,6 @@
 {
 	extern void tx4927_irq_init(void);
 
-	local_irq_disable();
-
 	tx4927_irq_init();
 	toshiba_rbtx4927_irq_ioc_init();
 #ifdef CONFIG_TOSHIBA_FPCIB0
@@ -681,8 +526,6 @@
 #endif
 
 	wbflush();
-
-	return;
 }
 
 void toshiba_rbtx4927_irq_dump(char *key)
@@ -715,7 +558,6 @@
 		}
 	}
 #endif
-	return;
 }
 
 void toshiba_rbtx4927_irq_dump_pics(char *s)
@@ -780,6 +622,4 @@
 				     level5_s);
 	TOSHIBA_RBTX4927_IRQ_DPRINTK(TOSHIBA_RBTX4927_IRQ_INFO, "[%s]\n",
 				     s);
-
-	return;
 }
diff --git a/arch/mips/tx4938/common/irq.c b/arch/mips/tx4938/common/irq.c
index 77fe245..42e1276 100644
--- a/arch/mips/tx4938/common/irq.c
+++ b/arch/mips/tx4938/common/irq.c
@@ -37,48 +37,36 @@
 /* Forwad definitions for all pic's                                               */
 /**********************************************************************************/
 
-static unsigned int tx4938_irq_cp0_startup(unsigned int irq);
-static void tx4938_irq_cp0_shutdown(unsigned int irq);
 static void tx4938_irq_cp0_enable(unsigned int irq);
 static void tx4938_irq_cp0_disable(unsigned int irq);
-static void tx4938_irq_cp0_mask_and_ack(unsigned int irq);
 static void tx4938_irq_cp0_end(unsigned int irq);
 
-static unsigned int tx4938_irq_pic_startup(unsigned int irq);
-static void tx4938_irq_pic_shutdown(unsigned int irq);
 static void tx4938_irq_pic_enable(unsigned int irq);
 static void tx4938_irq_pic_disable(unsigned int irq);
-static void tx4938_irq_pic_mask_and_ack(unsigned int irq);
 static void tx4938_irq_pic_end(unsigned int irq);
 
 /**********************************************************************************/
 /* Kernel structs for all pic's                                                   */
 /**********************************************************************************/
-DEFINE_SPINLOCK(tx4938_cp0_lock);
-DEFINE_SPINLOCK(tx4938_pic_lock);
 
 #define TX4938_CP0_NAME "TX4938-CP0"
 static struct irq_chip tx4938_irq_cp0_type = {
 	.typename = TX4938_CP0_NAME,
-	.startup = tx4938_irq_cp0_startup,
-	.shutdown = tx4938_irq_cp0_shutdown,
-	.enable = tx4938_irq_cp0_enable,
-	.disable = tx4938_irq_cp0_disable,
-	.ack = tx4938_irq_cp0_mask_and_ack,
+	.ack = tx4938_irq_cp0_disable,
+	.mask = tx4938_irq_cp0_disable,
+	.mask_ack = tx4938_irq_cp0_disable,
+	.unmask = tx4938_irq_cp0_enable,
 	.end = tx4938_irq_cp0_end,
-	.set_affinity = NULL
 };
 
 #define TX4938_PIC_NAME "TX4938-PIC"
 static struct irq_chip tx4938_irq_pic_type = {
 	.typename = TX4938_PIC_NAME,
-	.startup = tx4938_irq_pic_startup,
-	.shutdown = tx4938_irq_pic_shutdown,
-	.enable = tx4938_irq_pic_enable,
-	.disable = tx4938_irq_pic_disable,
-	.ack = tx4938_irq_pic_mask_and_ack,
+	.ack = tx4938_irq_pic_disable,
+	.mask = tx4938_irq_pic_disable,
+	.mask_ack = tx4938_irq_pic_disable,
+	.unmask = tx4938_irq_pic_enable,
 	.end = tx4938_irq_pic_end,
-	.set_affinity = NULL
 };
 
 static struct irqaction tx4938_irq_pic_action = {
@@ -99,56 +87,21 @@
 {
 	int i;
 
-	for (i = TX4938_IRQ_CP0_BEG; i <= TX4938_IRQ_CP0_END; i++) {
-		irq_desc[i].status = IRQ_DISABLED;
-		irq_desc[i].action = 0;
-		irq_desc[i].depth = 1;
-		irq_desc[i].chip = &tx4938_irq_cp0_type;
-	}
-}
-
-static unsigned int
-tx4938_irq_cp0_startup(unsigned int irq)
-{
-	tx4938_irq_cp0_enable(irq);
-
-	return 0;
-}
-
-static void
-tx4938_irq_cp0_shutdown(unsigned int irq)
-{
-	tx4938_irq_cp0_disable(irq);
+	for (i = TX4938_IRQ_CP0_BEG; i <= TX4938_IRQ_CP0_END; i++)
+		set_irq_chip_and_handler(i, &tx4938_irq_cp0_type,
+					 handle_level_irq);
 }
 
 static void
 tx4938_irq_cp0_enable(unsigned int irq)
 {
-	unsigned long flags;
-
-	spin_lock_irqsave(&tx4938_cp0_lock, flags);
-
 	set_c0_status(tx4938_irq_cp0_mask(irq));
-
-	spin_unlock_irqrestore(&tx4938_cp0_lock, flags);
 }
 
 static void
 tx4938_irq_cp0_disable(unsigned int irq)
 {
-	unsigned long flags;
-
-	spin_lock_irqsave(&tx4938_cp0_lock, flags);
-
 	clear_c0_status(tx4938_irq_cp0_mask(irq));
-
-	spin_unlock_irqrestore(&tx4938_cp0_lock, flags);
-}
-
-static void
-tx4938_irq_cp0_mask_and_ack(unsigned int irq)
-{
-	tx4938_irq_cp0_disable(irq);
 }
 
 static void
@@ -290,70 +243,30 @@
 static void __init
 tx4938_irq_pic_init(void)
 {
-	unsigned long flags;
 	int i;
 
-	for (i = TX4938_IRQ_PIC_BEG; i <= TX4938_IRQ_PIC_END; i++) {
-		irq_desc[i].status = IRQ_DISABLED;
-		irq_desc[i].action = 0;
-		irq_desc[i].depth = 2;
-		irq_desc[i].chip = &tx4938_irq_pic_type;
-	}
+	for (i = TX4938_IRQ_PIC_BEG; i <= TX4938_IRQ_PIC_END; i++)
+		set_irq_chip_and_handler(i, &tx4938_irq_pic_type,
+					 handle_level_irq);
 
 	setup_irq(TX4938_IRQ_NEST_PIC_ON_CP0, &tx4938_irq_pic_action);
 
-	spin_lock_irqsave(&tx4938_pic_lock, flags);
-
 	TX4938_WR(0xff1ff640, 0x6);	/* irq level mask -- only accept hightest */
 	TX4938_WR(0xff1ff600, TX4938_RD(0xff1ff600) | 0x1);	/* irq enable */
-
-	spin_unlock_irqrestore(&tx4938_pic_lock, flags);
-}
-
-static unsigned int
-tx4938_irq_pic_startup(unsigned int irq)
-{
-	tx4938_irq_pic_enable(irq);
-
-	return 0;
-}
-
-static void
-tx4938_irq_pic_shutdown(unsigned int irq)
-{
-	tx4938_irq_pic_disable(irq);
 }
 
 static void
 tx4938_irq_pic_enable(unsigned int irq)
 {
-	unsigned long flags;
-
-	spin_lock_irqsave(&tx4938_pic_lock, flags);
-
 	tx4938_irq_pic_modify(tx4938_irq_pic_addr(irq), 0,
 			      tx4938_irq_pic_mask(irq));
-
-	spin_unlock_irqrestore(&tx4938_pic_lock, flags);
 }
 
 static void
 tx4938_irq_pic_disable(unsigned int irq)
 {
-	unsigned long flags;
-
-	spin_lock_irqsave(&tx4938_pic_lock, flags);
-
 	tx4938_irq_pic_modify(tx4938_irq_pic_addr(irq),
 			      tx4938_irq_pic_mask(irq), 0);
-
-	spin_unlock_irqrestore(&tx4938_pic_lock, flags);
-}
-
-static void
-tx4938_irq_pic_mask_and_ack(unsigned int irq)
-{
-	tx4938_irq_pic_disable(irq);
 }
 
 static void
diff --git a/arch/mips/tx4938/common/setup.c b/arch/mips/tx4938/common/setup.c
index f415a1f..dc87d92 100644
--- a/arch/mips/tx4938/common/setup.c
+++ b/arch/mips/tx4938/common/setup.c
@@ -31,7 +31,6 @@
 #include <asm/mipsregs.h>
 #include <asm/system.h>
 #include <asm/time.h>
-#include <asm/time.h>
 #include <asm/tx4938/rbtx4938.h>
 
 extern void toshiba_rbtx4938_setup(void);
diff --git a/arch/mips/tx4938/toshiba_rbtx4938/irq.c b/arch/mips/tx4938/toshiba_rbtx4938/irq.c
index 102e473..8c87a35 100644
--- a/arch/mips/tx4938/toshiba_rbtx4938/irq.c
+++ b/arch/mips/tx4938/toshiba_rbtx4938/irq.c
@@ -87,25 +87,18 @@
 #include <linux/bootmem.h>
 #include <asm/tx4938/rbtx4938.h>
 
-static unsigned int toshiba_rbtx4938_irq_ioc_startup(unsigned int irq);
-static void toshiba_rbtx4938_irq_ioc_shutdown(unsigned int irq);
 static void toshiba_rbtx4938_irq_ioc_enable(unsigned int irq);
 static void toshiba_rbtx4938_irq_ioc_disable(unsigned int irq);
-static void toshiba_rbtx4938_irq_ioc_mask_and_ack(unsigned int irq);
 static void toshiba_rbtx4938_irq_ioc_end(unsigned int irq);
 
-DEFINE_SPINLOCK(toshiba_rbtx4938_ioc_lock);
-
 #define TOSHIBA_RBTX4938_IOC_NAME "RBTX4938-IOC"
 static struct irq_chip toshiba_rbtx4938_irq_ioc_type = {
 	.typename = TOSHIBA_RBTX4938_IOC_NAME,
-	.startup = toshiba_rbtx4938_irq_ioc_startup,
-	.shutdown = toshiba_rbtx4938_irq_ioc_shutdown,
-	.enable = toshiba_rbtx4938_irq_ioc_enable,
-	.disable = toshiba_rbtx4938_irq_ioc_disable,
-	.ack = toshiba_rbtx4938_irq_ioc_mask_and_ack,
+	.ack = toshiba_rbtx4938_irq_ioc_disable,
+	.mask = toshiba_rbtx4938_irq_ioc_disable,
+	.mask_ack = toshiba_rbtx4938_irq_ioc_disable,
+	.unmask = toshiba_rbtx4938_irq_ioc_enable,
 	.end = toshiba_rbtx4938_irq_ioc_end,
-	.set_affinity = NULL
 };
 
 #define TOSHIBA_RBTX4938_IOC_INTR_ENAB 0xb7f02000
@@ -142,69 +135,36 @@
 	int i;
 
 	for (i = TOSHIBA_RBTX4938_IRQ_IOC_BEG;
-	     i <= TOSHIBA_RBTX4938_IRQ_IOC_END; i++) {
-		irq_desc[i].status = IRQ_DISABLED;
-		irq_desc[i].action = 0;
-		irq_desc[i].depth = 3;
-		irq_desc[i].chip = &toshiba_rbtx4938_irq_ioc_type;
-	}
+	     i <= TOSHIBA_RBTX4938_IRQ_IOC_END; i++)
+		set_irq_chip_and_handler(i, &toshiba_rbtx4938_irq_ioc_type,
+					 handle_level_irq);
 
 	setup_irq(RBTX4938_IRQ_IOCINT,
 		  &toshiba_rbtx4938_irq_ioc_action);
 }
 
-static unsigned int
-toshiba_rbtx4938_irq_ioc_startup(unsigned int irq)
-{
-	toshiba_rbtx4938_irq_ioc_enable(irq);
-
-	return 0;
-}
-
-static void
-toshiba_rbtx4938_irq_ioc_shutdown(unsigned int irq)
-{
-	toshiba_rbtx4938_irq_ioc_disable(irq);
-}
-
 static void
 toshiba_rbtx4938_irq_ioc_enable(unsigned int irq)
 {
-	unsigned long flags;
 	volatile unsigned char v;
 
-	spin_lock_irqsave(&toshiba_rbtx4938_ioc_lock, flags);
-
 	v = TX4938_RD08(TOSHIBA_RBTX4938_IOC_INTR_ENAB);
 	v |= (1 << (irq - TOSHIBA_RBTX4938_IRQ_IOC_BEG));
 	TX4938_WR08(TOSHIBA_RBTX4938_IOC_INTR_ENAB, v);
 	mmiowb();
 	TX4938_RD08(TOSHIBA_RBTX4938_IOC_INTR_ENAB);
-
-	spin_unlock_irqrestore(&toshiba_rbtx4938_ioc_lock, flags);
 }
 
 static void
 toshiba_rbtx4938_irq_ioc_disable(unsigned int irq)
 {
-	unsigned long flags;
 	volatile unsigned char v;
 
-	spin_lock_irqsave(&toshiba_rbtx4938_ioc_lock, flags);
-
 	v = TX4938_RD08(TOSHIBA_RBTX4938_IOC_INTR_ENAB);
 	v &= ~(1 << (irq - TOSHIBA_RBTX4938_IRQ_IOC_BEG));
 	TX4938_WR08(TOSHIBA_RBTX4938_IOC_INTR_ENAB, v);
 	mmiowb();
 	TX4938_RD08(TOSHIBA_RBTX4938_IOC_INTR_ENAB);
-
-	spin_unlock_irqrestore(&toshiba_rbtx4938_ioc_lock, flags);
-}
-
-static void
-toshiba_rbtx4938_irq_ioc_mask_and_ack(unsigned int irq)
-{
-	toshiba_rbtx4938_irq_ioc_disable(irq);
 }
 
 static void
diff --git a/arch/mips/vr41xx/common/icu.c b/arch/mips/vr41xx/common/icu.c
index c215c0d..54b92a7 100644
--- a/arch/mips/vr41xx/common/icu.c
+++ b/arch/mips/vr41xx/common/icu.c
@@ -417,14 +417,7 @@
 
 EXPORT_SYMBOL(vr41xx_disable_bcuint);
 
-static unsigned int startup_sysint1_irq(unsigned int irq)
-{
-	icu1_set(MSYSINT1REG, 1 << SYSINT1_IRQ_TO_PIN(irq));
-
-	return 0; /* never anything pending */
-}
-
-static void shutdown_sysint1_irq(unsigned int irq)
+static void disable_sysint1_irq(unsigned int irq)
 {
 	icu1_clear(MSYSINT1REG, 1 << SYSINT1_IRQ_TO_PIN(irq));
 }
@@ -434,9 +427,6 @@
 	icu1_set(MSYSINT1REG, 1 << SYSINT1_IRQ_TO_PIN(irq));
 }
 
-#define disable_sysint1_irq	shutdown_sysint1_irq
-#define ack_sysint1_irq		shutdown_sysint1_irq
-
 static void end_sysint1_irq(unsigned int irq)
 {
 	if (!(irq_desc[irq].status & (IRQ_DISABLED | IRQ_INPROGRESS)))
@@ -445,22 +435,14 @@
 
 static struct irq_chip sysint1_irq_type = {
 	.typename	= "SYSINT1",
-	.startup	= startup_sysint1_irq,
-	.shutdown	= shutdown_sysint1_irq,
-	.enable		= enable_sysint1_irq,
-	.disable	= disable_sysint1_irq,
-	.ack		= ack_sysint1_irq,
+	.ack		= disable_sysint1_irq,
+	.mask		= disable_sysint1_irq,
+	.mask_ack	= disable_sysint1_irq,
+	.unmask		= enable_sysint1_irq,
 	.end		= end_sysint1_irq,
 };
 
-static unsigned int startup_sysint2_irq(unsigned int irq)
-{
-	icu2_set(MSYSINT2REG, 1 << SYSINT2_IRQ_TO_PIN(irq));
-
-	return 0; /* never anything pending */
-}
-
-static void shutdown_sysint2_irq(unsigned int irq)
+static void disable_sysint2_irq(unsigned int irq)
 {
 	icu2_clear(MSYSINT2REG, 1 << SYSINT2_IRQ_TO_PIN(irq));
 }
@@ -470,9 +452,6 @@
 	icu2_set(MSYSINT2REG, 1 << SYSINT2_IRQ_TO_PIN(irq));
 }
 
-#define disable_sysint2_irq	shutdown_sysint2_irq
-#define ack_sysint2_irq		shutdown_sysint2_irq
-
 static void end_sysint2_irq(unsigned int irq)
 {
 	if (!(irq_desc[irq].status & (IRQ_DISABLED | IRQ_INPROGRESS)))
@@ -481,11 +460,10 @@
 
 static struct irq_chip sysint2_irq_type = {
 	.typename	= "SYSINT2",
-	.startup	= startup_sysint2_irq,
-	.shutdown	= shutdown_sysint2_irq,
-	.enable		= enable_sysint2_irq,
-	.disable	= disable_sysint2_irq,
-	.ack		= ack_sysint2_irq,
+	.ack		= disable_sysint2_irq,
+	.mask		= disable_sysint2_irq,
+	.mask_ack	= disable_sysint2_irq,
+	.unmask		= enable_sysint2_irq,
 	.end		= end_sysint2_irq,
 };
 
@@ -723,10 +701,12 @@
 	icu2_write(MGIUINTHREG, 0xffff);
 
 	for (i = SYSINT1_IRQ_BASE; i <= SYSINT1_IRQ_LAST; i++)
-		irq_desc[i].chip = &sysint1_irq_type;
+		set_irq_chip_and_handler(i, &sysint1_irq_type,
+					 handle_level_irq);
 
 	for (i = SYSINT2_IRQ_BASE; i <= SYSINT2_IRQ_LAST; i++)
-		irq_desc[i].chip = &sysint2_irq_type;
+		set_irq_chip_and_handler(i, &sysint2_irq_type,
+					 handle_level_irq);
 
 	cascade_irq(INT0_IRQ, icu_get_irq);
 	cascade_irq(INT1_IRQ, icu_get_irq);
diff --git a/arch/mips/vr41xx/nec-cmbvr4133/irq.c b/arch/mips/vr41xx/nec-cmbvr4133/irq.c
index 2483487..a039bb7 100644
--- a/arch/mips/vr41xx/nec-cmbvr4133/irq.c
+++ b/arch/mips/vr41xx/nec-cmbvr4133/irq.c
@@ -30,17 +30,6 @@
 
 extern int vr4133_rockhopper;
 
-static unsigned int startup_i8259_irq(unsigned int irq)
-{
-	enable_8259A_irq(irq - I8259_IRQ_BASE);
-	return 0;
-}
-
-static void shutdown_i8259_irq(unsigned int irq)
-{
-	disable_8259A_irq(irq - I8259_IRQ_BASE);
-}
-
 static void enable_i8259_irq(unsigned int irq)
 {
 	enable_8259A_irq(irq - I8259_IRQ_BASE);
@@ -64,11 +53,10 @@
 
 static struct irq_chip i8259_irq_type = {
 	.typename       = "XT-PIC",
-	.startup        = startup_i8259_irq,
-	.shutdown       = shutdown_i8259_irq,
-	.enable         = enable_i8259_irq,
-	.disable        = disable_i8259_irq,
 	.ack            = ack_i8259_irq,
+	.mask		= disable_i8259_irq,
+	.mask_ack	= ack_i8259_irq,
+	.unmask		= enable_i8259_irq,
 	.end            = end_i8259_irq,
 };
 
@@ -104,7 +92,7 @@
 	}
 
 	for (i = I8259_IRQ_BASE; i <= I8259_IRQ_LAST; i++)
-		irq_desc[i].chip = &i8259_irq_type;
+		set_irq_chip(i, &i8259_irq_type);
 
 	setup_irq(I8259_SLAVE_IRQ, &i8259_slave_cascade);
 
diff --git a/arch/powerpc/Kconfig b/arch/powerpc/Kconfig
index 0673dbe..116d7d3 100644
--- a/arch/powerpc/Kconfig
+++ b/arch/powerpc/Kconfig
@@ -425,7 +425,7 @@
 	default n
 	help
           This option enables support for the Maple 970FX Evaluation Board.
-	  For more informations, refer to <http://www.970eval.com>
+	  For more information, refer to <http://www.970eval.com>
 
 config PPC_PASEMI
 	depends on PPC_MULTIPLATFORM && PPC64
diff --git a/arch/powerpc/platforms/83xx/Kconfig b/arch/powerpc/platforms/83xx/Kconfig
index 7edb6b4..edcd5b8 100644
--- a/arch/powerpc/platforms/83xx/Kconfig
+++ b/arch/powerpc/platforms/83xx/Kconfig
@@ -21,7 +21,7 @@
 	  Be aware that PCI buses can only function when SYS board is plugged
 	  into the PIB (Platform IO Board) board from Freescale which provide
 	  3 PCI slots.  The PIBs PCI initialization is the bootloader's
-	  responsiblilty.
+	  responsibility.
 
 config MPC834x_ITX
 	bool "Freescale MPC834x ITX"
@@ -30,7 +30,7 @@
 	  This option enables support for the MPC 834x ITX evaluation board.
 
 	  Be aware that PCI initialization is the bootloader's
-	  responsiblilty.
+	  responsibility.
 
 config MPC8360E_PB
 	bool "Freescale MPC8360E PB"
diff --git a/arch/powerpc/platforms/powermac/pci.c b/arch/powerpc/platforms/powermac/pci.c
index 9923adc..257dc90 100644
--- a/arch/powerpc/platforms/powermac/pci.c
+++ b/arch/powerpc/platforms/powermac/pci.c
@@ -48,7 +48,6 @@
 static int has_second_ohare;
 #endif /* CONFIG_PPC64 */
 
-extern u8 pci_cache_line_size;
 extern int pcibios_assign_bus_offset;
 
 struct device_node *k2_skiplist[2];
diff --git a/arch/ppc/Kconfig b/arch/ppc/Kconfig
index 077711e..ef018e2 100644
--- a/arch/ppc/Kconfig
+++ b/arch/ppc/Kconfig
@@ -724,7 +724,7 @@
 	  Be aware that PCI buses can only function when SYS board is plugged
 	  into the PIB (Platform IO Board) board from Freescale which provide
 	  3 PCI slots.  The PIBs PCI initialization is the bootloader's
-	  responsiblilty.
+	  responsibility.
 
 config EV64360
 	bool "Marvell-EV64360BP"
diff --git a/arch/sh/Kconfig b/arch/sh/Kconfig
index 6a461d4..bffc7e1 100644
--- a/arch/sh/Kconfig
+++ b/arch/sh/Kconfig
@@ -217,7 +217,7 @@
 	bool "SHMIN"
 	select CPU_SUBTYPE_SH7706
 	help
-	  Select SHMIN if configureing for the SHMIN board
+	  Select SHMIN if configuring for the SHMIN board.
 
 config SH_UNKNOWN
 	bool "BareCPU"
diff --git a/arch/sh64/lib/dbg.c b/arch/sh64/lib/dbg.c
index 1326f45..4310fc8 100644
--- a/arch/sh64/lib/dbg.c
+++ b/arch/sh64/lib/dbg.c
@@ -383,7 +383,7 @@
 /* ======================================================================= */
 
 /*
-** Depending on <base> scan the MMU, Data or Instrction side
+** Depending on <base> scan the MMU, Data or Instruction side
 ** looking for a valid mapping matching Eaddr & asid.
 ** Return -1 if not found or the TLB id entry otherwise.
 ** Note: it works only for 4k pages!
diff --git a/arch/sparc/Kconfig b/arch/sparc/Kconfig
index 2f96610..92a7c8a 100644
--- a/arch/sparc/Kconfig
+++ b/arch/sparc/Kconfig
@@ -212,8 +212,8 @@
 	tristate "Sun4m LED driver"
 	help
 	  This driver toggles the front-panel LED on sun4m systems
-	  in a user-specifyable manner.  It's state can be probed
-	  by reading /proc/led and it's blinking mode can be changed
+	  in a user-specifiable manner.  Its state can be probed
+	  by reading /proc/led and its blinking mode can be changed
 	  via writes to /proc/led
 
 source "fs/Kconfig.binfmt"
diff --git a/arch/sparc64/kernel/pci.c b/arch/sparc64/kernel/pci.c
index e02f01b..dfc41cd 100644
--- a/arch/sparc64/kernel/pci.c
+++ b/arch/sparc64/kernel/pci.c
@@ -646,13 +646,4 @@
 }
 EXPORT_SYMBOL(pci_domain_nr);
 
-int pcibios_prep_mwi(struct pci_dev *dev)
-{
-	/* We set correct PCI_CACHE_LINE_SIZE register values for every
-	 * device probed on this platform.  So there is nothing to check
-	 * and this always succeeds.
-	 */
-	return 0;
-}
-
 #endif /* !(CONFIG_PCI) */
diff --git a/arch/um/drivers/chan_user.c b/arch/um/drivers/chan_user.c
index 2f880cb..0cad354 100644
--- a/arch/um/drivers/chan_user.c
+++ b/arch/um/drivers/chan_user.c
@@ -120,7 +120,7 @@
 	/* These are synchronization calls between various UML threads on the
 	 * host - since they are not different kernel threads, we cannot use
 	 * kernel semaphores. We don't use SysV semaphores because they are
-	 * persistant. */
+	 * persistent. */
 	count = os_read_file(pipe_fd, &c, sizeof(c));
 	if(count != sizeof(c))
 		printk("winch_thread : failed to read synchronization byte, "
diff --git a/block/as-iosched.c b/block/as-iosched.c
index 50b95e4..0024211 100644
--- a/block/as-iosched.c
+++ b/block/as-iosched.c
@@ -1317,7 +1317,7 @@
 /*
  * initialize elevator private data (as_data).
  */
-static void *as_init_queue(request_queue_t *q, elevator_t *e)
+static void *as_init_queue(request_queue_t *q)
 {
 	struct as_data *ad;
 
diff --git a/block/blktrace.c b/block/blktrace.c
index 135593c..562ca7c 100644
--- a/block/blktrace.c
+++ b/block/blktrace.c
@@ -22,30 +22,61 @@
 #include <linux/init.h>
 #include <linux/mutex.h>
 #include <linux/debugfs.h>
+#include <linux/time.h>
 #include <asm/uaccess.h>
 
 static DEFINE_PER_CPU(unsigned long long, blk_trace_cpu_offset) = { 0, };
 static unsigned int blktrace_seq __read_mostly = 1;
 
 /*
+ * Send out a notify message.
+ */
+static inline unsigned int trace_note(struct blk_trace *bt,
+		pid_t pid, int action,
+		const void *data, size_t len)
+{
+	struct blk_io_trace *t;
+	int cpu = smp_processor_id();
+
+	t = relay_reserve(bt->rchan, sizeof(*t) + len);
+	if (t == NULL)
+		return 0;
+
+	t->magic = BLK_IO_TRACE_MAGIC | BLK_IO_TRACE_VERSION;
+	t->time = sched_clock() - per_cpu(blk_trace_cpu_offset, cpu);
+	t->device = bt->dev;
+	t->action = action;
+	t->pid = pid;
+	t->cpu = cpu;
+	t->pdu_len = len;
+	memcpy((void *) t + sizeof(*t), data, len);
+	return blktrace_seq;
+}
+
+/*
  * Send out a notify for this process, if we haven't done so since a trace
  * started
  */
 static void trace_note_tsk(struct blk_trace *bt, struct task_struct *tsk)
 {
-	struct blk_io_trace *t;
+	tsk->btrace_seq = trace_note(bt, tsk->pid,
+			BLK_TN_PROCESS,
+			tsk->comm, sizeof(tsk->comm));
+}
 
-	t = relay_reserve(bt->rchan, sizeof(*t) + sizeof(tsk->comm));
-	if (t) {
-		t->magic = BLK_IO_TRACE_MAGIC | BLK_IO_TRACE_VERSION;
-		t->device = bt->dev;
-		t->action = BLK_TC_ACT(BLK_TC_NOTIFY);
-		t->pid = tsk->pid;
-		t->cpu = smp_processor_id();
-		t->pdu_len = sizeof(tsk->comm);
-		memcpy((void *) t + sizeof(*t), tsk->comm, t->pdu_len);
-		tsk->btrace_seq = blktrace_seq;
-	}
+static void trace_note_time(struct blk_trace *bt)
+{
+	struct timespec now;
+	unsigned long flags;
+	u32 words[2];
+
+	getnstimeofday(&now);
+	words[0] = now.tv_sec;
+	words[1] = now.tv_nsec;
+
+	local_irq_save(flags);
+	trace_note(bt, 0, BLK_TN_TIMESTAMP, words, sizeof(words));
+	local_irq_restore(flags);
 }
 
 static int act_log_check(struct blk_trace *bt, u32 what, sector_t sector,
@@ -394,6 +425,8 @@
 			blktrace_seq++;
 			smp_mb();
 			bt->trace_state = Blktrace_running;
+
+			trace_note_time(bt);
 			ret = 0;
 		}
 	} else {
diff --git a/block/cfq-iosched.c b/block/cfq-iosched.c
index 1d9c3c7..e9019ed 100644
--- a/block/cfq-iosched.c
+++ b/block/cfq-iosched.c
@@ -1464,8 +1464,7 @@
 }
 
 static void
-cfq_update_io_seektime(struct cfq_data *cfqd, struct cfq_io_context *cic,
-		       struct request *rq)
+cfq_update_io_seektime(struct cfq_io_context *cic, struct request *rq)
 {
 	sector_t sdist;
 	u64 total;
@@ -1617,7 +1616,7 @@
 	}
 
 	cfq_update_io_thinktime(cfqd, cic);
-	cfq_update_io_seektime(cfqd, cic, rq);
+	cfq_update_io_seektime(cic, rq);
 	cfq_update_idle_window(cfqd, cfqq, cic);
 
 	cic->last_queue = jiffies;
@@ -1770,7 +1769,7 @@
 /*
  * queue lock held here
  */
-static void cfq_put_request(request_queue_t *q, struct request *rq)
+static void cfq_put_request(struct request *rq)
 {
 	struct cfq_queue *cfqq = RQ_CFQQ(rq);
 
@@ -1951,7 +1950,7 @@
 	kfree(cfqd);
 }
 
-static void *cfq_init_queue(request_queue_t *q, elevator_t *e)
+static void *cfq_init_queue(request_queue_t *q)
 {
 	struct cfq_data *cfqd;
 	int i;
diff --git a/block/deadline-iosched.c b/block/deadline-iosched.c
index b7c5b34..6d673e9 100644
--- a/block/deadline-iosched.c
+++ b/block/deadline-iosched.c
@@ -356,7 +356,7 @@
 /*
  * initialize elevator private data (deadline_data).
  */
-static void *deadline_init_queue(request_queue_t *q, elevator_t *e)
+static void *deadline_init_queue(request_queue_t *q)
 {
 	struct deadline_data *dd;
 
diff --git a/block/elevator.c b/block/elevator.c
index 8ccd163..c0063f3 100644
--- a/block/elevator.c
+++ b/block/elevator.c
@@ -129,7 +129,7 @@
 
 static void *elevator_init_queue(request_queue_t *q, struct elevator_queue *eq)
 {
-	return eq->ops->elevator_init_fn(q, eq);
+	return eq->ops->elevator_init_fn(q);
 }
 
 static void elevator_attach(request_queue_t *q, struct elevator_queue *eq,
@@ -810,7 +810,7 @@
 	elevator_t *e = q->elevator;
 
 	if (e->ops->elevator_put_req_fn)
-		e->ops->elevator_put_req_fn(q, rq);
+		e->ops->elevator_put_req_fn(rq);
 }
 
 int elv_may_queue(request_queue_t *q, int rw)
diff --git a/block/ll_rw_blk.c b/block/ll_rw_blk.c
index 9eaee66..0f82e12 100644
--- a/block/ll_rw_blk.c
+++ b/block/ll_rw_blk.c
@@ -2322,6 +2322,84 @@
 
 EXPORT_SYMBOL(blk_insert_request);
 
+static int __blk_rq_unmap_user(struct bio *bio)
+{
+	int ret = 0;
+
+	if (bio) {
+		if (bio_flagged(bio, BIO_USER_MAPPED))
+			bio_unmap_user(bio);
+		else
+			ret = bio_uncopy_user(bio);
+	}
+
+	return ret;
+}
+
+static int __blk_rq_map_user(request_queue_t *q, struct request *rq,
+			     void __user *ubuf, unsigned int len)
+{
+	unsigned long uaddr;
+	struct bio *bio, *orig_bio;
+	int reading, ret;
+
+	reading = rq_data_dir(rq) == READ;
+
+	/*
+	 * if alignment requirement is satisfied, map in user pages for
+	 * direct dma. else, set up kernel bounce buffers
+	 */
+	uaddr = (unsigned long) ubuf;
+	if (!(uaddr & queue_dma_alignment(q)) && !(len & queue_dma_alignment(q)))
+		bio = bio_map_user(q, NULL, uaddr, len, reading);
+	else
+		bio = bio_copy_user(q, uaddr, len, reading);
+
+	if (IS_ERR(bio)) {
+		return PTR_ERR(bio);
+	}
+
+	orig_bio = bio;
+	blk_queue_bounce(q, &bio);
+	/*
+	 * We link the bounce buffer in and could have to traverse it
+	 * later so we have to get a ref to prevent it from being freed
+	 */
+	bio_get(bio);
+
+	/*
+	 * for most (all? don't know of any) queues we could
+	 * skip grabbing the queue lock here. only drivers with
+	 * funky private ->back_merge_fn() function could be
+	 * problematic.
+	 */
+	spin_lock_irq(q->queue_lock);
+	if (!rq->bio)
+		blk_rq_bio_prep(q, rq, bio);
+	else if (!q->back_merge_fn(q, rq, bio)) {
+		ret = -EINVAL;
+		spin_unlock_irq(q->queue_lock);
+		goto unmap_bio;
+	} else {
+		rq->biotail->bi_next = bio;
+		rq->biotail = bio;
+
+		rq->nr_sectors += bio_sectors(bio);
+		rq->hard_nr_sectors = rq->nr_sectors;
+		rq->data_len += bio->bi_size;
+	}
+	spin_unlock_irq(q->queue_lock);
+
+	return bio->bi_size;
+
+unmap_bio:
+	/* if it was boucned we must call the end io function */
+	bio_endio(bio, bio->bi_size, 0);
+	__blk_rq_unmap_user(orig_bio);
+	bio_put(bio);
+	return ret;
+}
+
 /**
  * blk_rq_map_user - map user data to a request, for REQ_BLOCK_PC usage
  * @q:		request queue where request should be inserted
@@ -2343,42 +2421,44 @@
  *    unmapping.
  */
 int blk_rq_map_user(request_queue_t *q, struct request *rq, void __user *ubuf,
-		    unsigned int len)
+		    unsigned long len)
 {
-	unsigned long uaddr;
-	struct bio *bio;
-	int reading;
+	unsigned long bytes_read = 0;
+	int ret;
 
 	if (len > (q->max_hw_sectors << 9))
 		return -EINVAL;
 	if (!len || !ubuf)
 		return -EINVAL;
 
-	reading = rq_data_dir(rq) == READ;
+	while (bytes_read != len) {
+		unsigned long map_len, end, start;
 
-	/*
-	 * if alignment requirement is satisfied, map in user pages for
-	 * direct dma. else, set up kernel bounce buffers
-	 */
-	uaddr = (unsigned long) ubuf;
-	if (!(uaddr & queue_dma_alignment(q)) && !(len & queue_dma_alignment(q)))
-		bio = bio_map_user(q, NULL, uaddr, len, reading);
-	else
-		bio = bio_copy_user(q, uaddr, len, reading);
+		map_len = min_t(unsigned long, len - bytes_read, BIO_MAX_SIZE);
+		end = ((unsigned long)ubuf + map_len + PAGE_SIZE - 1)
+								>> PAGE_SHIFT;
+		start = (unsigned long)ubuf >> PAGE_SHIFT;
 
-	if (!IS_ERR(bio)) {
-		rq->bio = rq->biotail = bio;
-		blk_rq_bio_prep(q, rq, bio);
+		/*
+		 * A bad offset could cause us to require BIO_MAX_PAGES + 1
+		 * pages. If this happens we just lower the requested
+		 * mapping len by a page so that we can fit
+		 */
+		if (end - start > BIO_MAX_PAGES)
+			map_len -= PAGE_SIZE;
 
-		rq->buffer = rq->data = NULL;
-		rq->data_len = len;
-		return 0;
+		ret = __blk_rq_map_user(q, rq, ubuf, map_len);
+		if (ret < 0)
+			goto unmap_rq;
+		bytes_read += ret;
+		ubuf += ret;
 	}
 
-	/*
-	 * bio is the err-ptr
-	 */
-	return PTR_ERR(bio);
+	rq->buffer = rq->data = NULL;
+	return 0;
+unmap_rq:
+	blk_rq_unmap_user(rq);
+	return ret;
 }
 
 EXPORT_SYMBOL(blk_rq_map_user);
@@ -2404,7 +2484,7 @@
  *    unmapping.
  */
 int blk_rq_map_user_iov(request_queue_t *q, struct request *rq,
-			struct sg_iovec *iov, int iov_count)
+			struct sg_iovec *iov, int iov_count, unsigned int len)
 {
 	struct bio *bio;
 
@@ -2418,10 +2498,15 @@
 	if (IS_ERR(bio))
 		return PTR_ERR(bio);
 
-	rq->bio = rq->biotail = bio;
+	if (bio->bi_size != len) {
+		bio_endio(bio, bio->bi_size, 0);
+		bio_unmap_user(bio);
+		return -EINVAL;
+	}
+
+	bio_get(bio);
 	blk_rq_bio_prep(q, rq, bio);
 	rq->buffer = rq->data = NULL;
-	rq->data_len = bio->bi_size;
 	return 0;
 }
 
@@ -2429,23 +2514,26 @@
 
 /**
  * blk_rq_unmap_user - unmap a request with user data
- * @bio:	bio to be unmapped
- * @ulen:	length of user buffer
+ * @rq:		rq to be unmapped
  *
  * Description:
- *    Unmap a bio previously mapped by blk_rq_map_user().
+ *    Unmap a rq previously mapped by blk_rq_map_user().
+ *    rq->bio must be set to the original head of the request.
  */
-int blk_rq_unmap_user(struct bio *bio, unsigned int ulen)
+int blk_rq_unmap_user(struct request *rq)
 {
-	int ret = 0;
+	struct bio *bio, *mapped_bio;
 
-	if (bio) {
-		if (bio_flagged(bio, BIO_USER_MAPPED))
-			bio_unmap_user(bio);
+	while ((bio = rq->bio)) {
+		if (bio_flagged(bio, BIO_BOUNCED))
+			mapped_bio = bio->bi_private;
 		else
-			ret = bio_uncopy_user(bio);
-	}
+			mapped_bio = bio;
 
+		__blk_rq_unmap_user(mapped_bio);
+		rq->bio = bio->bi_next;
+		bio_put(bio);
+	}
 	return 0;
 }
 
@@ -2476,11 +2564,8 @@
 	if (rq_data_dir(rq) == WRITE)
 		bio->bi_rw |= (1 << BIO_RW);
 
-	rq->bio = rq->biotail = bio;
 	blk_rq_bio_prep(q, rq, bio);
-
 	rq->buffer = rq->data = NULL;
-	rq->data_len = len;
 	return 0;
 }
 
@@ -3495,6 +3580,7 @@
 	rq->hard_cur_sectors = rq->current_nr_sectors;
 	rq->hard_nr_sectors = rq->nr_sectors = bio_sectors(bio);
 	rq->buffer = bio_data(bio);
+	rq->data_len = bio->bi_size;
 
 	rq->bio = rq->biotail = bio;
 }
diff --git a/block/noop-iosched.c b/block/noop-iosched.c
index 79af431..1c3de2b 100644
--- a/block/noop-iosched.c
+++ b/block/noop-iosched.c
@@ -65,7 +65,7 @@
 	return list_entry(rq->queuelist.next, struct request, queuelist);
 }
 
-static void *noop_init_queue(request_queue_t *q, elevator_t *e)
+static void *noop_init_queue(request_queue_t *q)
 {
 	struct noop_data *nd;
 
diff --git a/block/scsi_ioctl.c b/block/scsi_ioctl.c
index e55a756..5493c2f 100644
--- a/block/scsi_ioctl.c
+++ b/block/scsi_ioctl.c
@@ -226,7 +226,6 @@
 	unsigned long start_time;
 	int writing = 0, ret = 0;
 	struct request *rq;
-	struct bio *bio;
 	char sense[SCSI_SENSE_BUFFERSIZE];
 	unsigned char cmd[BLK_MAX_CDB];
 
@@ -258,6 +257,32 @@
 	if (!rq)
 		return -ENOMEM;
 
+	/*
+	 * fill in request structure
+	 */
+	rq->cmd_len = hdr->cmd_len;
+	memset(rq->cmd, 0, BLK_MAX_CDB); /* ATAPI hates garbage after CDB */
+	memcpy(rq->cmd, cmd, hdr->cmd_len);
+
+	memset(sense, 0, sizeof(sense));
+	rq->sense = sense;
+	rq->sense_len = 0;
+
+	rq->cmd_type = REQ_TYPE_BLOCK_PC;
+
+	/*
+	 * bounce this after holding a reference to the original bio, it's
+	 * needed for proper unmapping
+	 */
+	if (rq->bio)
+		blk_queue_bounce(q, &rq->bio);
+
+	rq->timeout = (hdr->timeout * HZ) / 1000;
+	if (!rq->timeout)
+		rq->timeout = q->sg_timeout;
+	if (!rq->timeout)
+		rq->timeout = BLK_DEFAULT_TIMEOUT;
+
 	if (hdr->iovec_count) {
 		const int size = sizeof(struct sg_iovec) * hdr->iovec_count;
 		struct sg_iovec *iov;
@@ -274,7 +299,8 @@
 			goto out;
 		}
 
-		ret = blk_rq_map_user_iov(q, rq, iov, hdr->iovec_count);
+		ret = blk_rq_map_user_iov(q, rq, iov, hdr->iovec_count,
+					  hdr->dxfer_len);
 		kfree(iov);
 	} else if (hdr->dxfer_len)
 		ret = blk_rq_map_user(q, rq, hdr->dxferp, hdr->dxfer_len);
@@ -282,33 +308,6 @@
 	if (ret)
 		goto out;
 
-	/*
-	 * fill in request structure
-	 */
-	rq->cmd_len = hdr->cmd_len;
-	memset(rq->cmd, 0, BLK_MAX_CDB); /* ATAPI hates garbage after CDB */
-	memcpy(rq->cmd, cmd, hdr->cmd_len);
-
-	memset(sense, 0, sizeof(sense));
-	rq->sense = sense;
-	rq->sense_len = 0;
-
-	rq->cmd_type = REQ_TYPE_BLOCK_PC;
-	bio = rq->bio;
-
-	/*
-	 * bounce this after holding a reference to the original bio, it's
-	 * needed for proper unmapping
-	 */
-	if (rq->bio)
-		blk_queue_bounce(q, &rq->bio);
-
-	rq->timeout = (hdr->timeout * HZ) / 1000;
-	if (!rq->timeout)
-		rq->timeout = q->sg_timeout;
-	if (!rq->timeout)
-		rq->timeout = BLK_DEFAULT_TIMEOUT;
-
 	rq->retries = 0;
 
 	start_time = jiffies;
@@ -339,7 +338,7 @@
 			hdr->sb_len_wr = len;
 	}
 
-	if (blk_rq_unmap_user(bio, hdr->dxfer_len))
+	if (blk_rq_unmap_user(rq))
 		ret = -EFAULT;
 
 	/* may not have succeeded, but output values written to control
diff --git a/drivers/acpi/glue.c b/drivers/acpi/glue.c
index 10f160d..a2f46d5 100644
--- a/drivers/acpi/glue.c
+++ b/drivers/acpi/glue.c
@@ -267,9 +267,9 @@
 {
 	acpi_status status;
 
-	if (dev->firmware_data) {
+	if (dev->archdata.acpi_handle) {
 		printk(KERN_WARNING PREFIX
-		       "Drivers changed 'firmware_data' for %s\n", dev->bus_id);
+		       "Drivers changed 'acpi_handle' for %s\n", dev->bus_id);
 		return -EINVAL;
 	}
 	get_device(dev);
@@ -278,25 +278,26 @@
 		put_device(dev);
 		return -EINVAL;
 	}
-	dev->firmware_data = handle;
+	dev->archdata.acpi_handle = handle;
 
 	return 0;
 }
 
 static int acpi_unbind_one(struct device *dev)
 {
-	if (!dev->firmware_data)
+	if (!dev->archdata.acpi_handle)
 		return 0;
-	if (dev == acpi_get_physical_device(dev->firmware_data)) {
+	if (dev == acpi_get_physical_device(dev->archdata.acpi_handle)) {
 		/* acpi_get_physical_device increase refcnt by one */
 		put_device(dev);
-		acpi_detach_data(dev->firmware_data, acpi_glue_data_handler);
-		dev->firmware_data = NULL;
+		acpi_detach_data(dev->archdata.acpi_handle,
+				 acpi_glue_data_handler);
+		dev->archdata.acpi_handle = NULL;
 		/* acpi_bind_one increase refcnt by one */
 		put_device(dev);
 	} else {
 		printk(KERN_ERR PREFIX
-		       "Oops, 'firmware_data' corrupt for %s\n", dev->bus_id);
+		       "Oops, 'acpi_handle' corrupt for %s\n", dev->bus_id);
 	}
 	return 0;
 }
@@ -328,7 +329,8 @@
 	if (!ret) {
 		struct acpi_buffer buffer = { ACPI_ALLOCATE_BUFFER, NULL };
 
-		acpi_get_name(dev->firmware_data, ACPI_FULL_PATHNAME, &buffer);
+		acpi_get_name(dev->archdata.acpi_handle,
+			      ACPI_FULL_PATHNAME, &buffer);
 		DBG("Device %s -> %s\n", dev->bus_id, (char *)buffer.pointer);
 		kfree(buffer.pointer);
 	} else
diff --git a/drivers/ata/ahci.c b/drivers/ata/ahci.c
index f510e11..bddb14e 100644
--- a/drivers/ata/ahci.c
+++ b/drivers/ata/ahci.c
@@ -78,6 +78,7 @@
 
 	board_ahci		= 0,
 	board_ahci_vt8251	= 1,
+	board_ahci_ign_iferr	= 2,
 
 	/* global controller registers */
 	HOST_CAP		= 0x00, /* host capabilities */
@@ -168,6 +169,7 @@
 	/* ap->flags bits */
 	AHCI_FLAG_RESET_NEEDS_CLO	= (1 << 24),
 	AHCI_FLAG_NO_NCQ		= (1 << 25),
+	AHCI_FLAG_IGN_IRQ_IF_ERR	= (1 << 26), /* ignore IRQ_IF_ERR */
 };
 
 struct ahci_cmd_hdr {
@@ -295,6 +297,17 @@
 		.udma_mask	= 0x7f, /* udma0-6 ; FIXME */
 		.port_ops	= &ahci_ops,
 	},
+	/* board_ahci_ign_iferr */
+	{
+		.sht		= &ahci_sht,
+		.flags		= ATA_FLAG_SATA | ATA_FLAG_NO_LEGACY |
+				  ATA_FLAG_MMIO | ATA_FLAG_PIO_DMA |
+				  ATA_FLAG_SKIP_D2H_BSY |
+				  AHCI_FLAG_IGN_IRQ_IF_ERR,
+		.pio_mask	= 0x1f, /* pio0-4 */
+		.udma_mask	= 0x7f, /* udma0-6 ; FIXME */
+		.port_ops	= &ahci_ops,
+	},
 };
 
 static const struct pci_device_id ahci_pci_tbl[] = {
@@ -327,11 +340,11 @@
 	{ PCI_VDEVICE(INTEL, 0x294e), board_ahci }, /* ICH9M */
 
 	/* JMicron */
-	{ PCI_VDEVICE(JMICRON, 0x2360), board_ahci }, /* JMicron JMB360 */
-	{ PCI_VDEVICE(JMICRON, 0x2361), board_ahci }, /* JMicron JMB361 */
-	{ PCI_VDEVICE(JMICRON, 0x2363), board_ahci }, /* JMicron JMB363 */
-	{ PCI_VDEVICE(JMICRON, 0x2365), board_ahci }, /* JMicron JMB365 */
-	{ PCI_VDEVICE(JMICRON, 0x2366), board_ahci }, /* JMicron JMB366 */
+	{ PCI_VDEVICE(JMICRON, 0x2360), board_ahci_ign_iferr }, /* JMB360 */
+	{ PCI_VDEVICE(JMICRON, 0x2361), board_ahci_ign_iferr }, /* JMB361 */
+	{ PCI_VDEVICE(JMICRON, 0x2363), board_ahci_ign_iferr }, /* JMB363 */
+	{ PCI_VDEVICE(JMICRON, 0x2365), board_ahci_ign_iferr }, /* JMB365 */
+	{ PCI_VDEVICE(JMICRON, 0x2366), board_ahci_ign_iferr }, /* JMB366 */
 
 	/* ATI */
 	{ PCI_VDEVICE(ATI, 0x4380), board_ahci }, /* ATI SB600 non-raid */
@@ -980,6 +993,10 @@
 	/* analyze @irq_stat */
 	ata_ehi_push_desc(ehi, "irq_stat 0x%08x", irq_stat);
 
+	/* some controllers set IRQ_IF_ERR on device errors, ignore it */
+	if (ap->flags & AHCI_FLAG_IGN_IRQ_IF_ERR)
+		irq_stat &= ~PORT_IRQ_IF_ERR;
+
 	if (irq_stat & PORT_IRQ_TF_ERR)
 		err_mask |= AC_ERR_DEV;
 
diff --git a/drivers/ata/ata_generic.c b/drivers/ata/ata_generic.c
index 377425e..4a80ff9 100644
--- a/drivers/ata/ata_generic.c
+++ b/drivers/ata/ata_generic.c
@@ -116,6 +116,7 @@
 	.proc_name		= DRV_NAME,
 	.dma_boundary		= ATA_DMA_BOUNDARY,
 	.slave_configure	= ata_scsi_slave_config,
+	.slave_destroy		= ata_scsi_slave_destroy,
 	.bios_param		= ata_std_bios_param,
 };
 
diff --git a/drivers/ata/pata_ali.c b/drivers/ata/pata_ali.c
index 1d695df..64eed99 100644
--- a/drivers/ata/pata_ali.c
+++ b/drivers/ata/pata_ali.c
@@ -346,6 +346,7 @@
 	.proc_name		= DRV_NAME,
 	.dma_boundary		= ATA_DMA_BOUNDARY,
 	.slave_configure	= ata_scsi_slave_config,
+	.slave_destroy		= ata_scsi_slave_destroy,
 	.bios_param		= ata_std_bios_param,
 };
 
diff --git a/drivers/ata/pata_amd.c b/drivers/ata/pata_amd.c
index 5c47a9e..8be46a6 100644
--- a/drivers/ata/pata_amd.c
+++ b/drivers/ata/pata_amd.c
@@ -333,6 +333,7 @@
 	.proc_name		= DRV_NAME,
 	.dma_boundary		= ATA_DMA_BOUNDARY,
 	.slave_configure	= ata_scsi_slave_config,
+	.slave_destroy		= ata_scsi_slave_destroy,
 	.bios_param		= ata_std_bios_param,
 };
 
diff --git a/drivers/ata/pata_artop.c b/drivers/ata/pata_artop.c
index 96a0980..2cd3076 100644
--- a/drivers/ata/pata_artop.c
+++ b/drivers/ata/pata_artop.c
@@ -314,6 +314,7 @@
 	.proc_name		= DRV_NAME,
 	.dma_boundary		= ATA_DMA_BOUNDARY,
 	.slave_configure	= ata_scsi_slave_config,
+	.slave_destroy		= ata_scsi_slave_destroy,
 	.bios_param		= ata_std_bios_param,
 };
 
diff --git a/drivers/ata/pata_atiixp.c b/drivers/ata/pata_atiixp.c
index 1ce28d2..4e1d3b5 100644
--- a/drivers/ata/pata_atiixp.c
+++ b/drivers/ata/pata_atiixp.c
@@ -216,6 +216,7 @@
 	.proc_name		= DRV_NAME,
 	.dma_boundary		= ATA_DMA_BOUNDARY,
 	.slave_configure	= ata_scsi_slave_config,
+	.slave_destroy		= ata_scsi_slave_destroy,
 	.bios_param		= ata_std_bios_param,
 };
 
diff --git a/drivers/ata/pata_cmd64x.c b/drivers/ata/pata_cmd64x.c
index b9bbd1d..29a60df 100644
--- a/drivers/ata/pata_cmd64x.c
+++ b/drivers/ata/pata_cmd64x.c
@@ -275,6 +275,7 @@
 	.proc_name		= DRV_NAME,
 	.dma_boundary		= ATA_DMA_BOUNDARY,
 	.slave_configure	= ata_scsi_slave_config,
+	.slave_destroy		= ata_scsi_slave_destroy,
 	.bios_param		= ata_std_bios_param,
 };
 
diff --git a/drivers/ata/pata_cs5520.c b/drivers/ata/pata_cs5520.c
index 2cd3c0f..33d2b88 100644
--- a/drivers/ata/pata_cs5520.c
+++ b/drivers/ata/pata_cs5520.c
@@ -166,6 +166,7 @@
 	.proc_name		= DRV_NAME,
 	.dma_boundary		= ATA_DMA_BOUNDARY,
 	.slave_configure	= ata_scsi_slave_config,
+	.slave_destroy		= ata_scsi_slave_destroy,
 	.bios_param		= ata_std_bios_param,
 };
 
diff --git a/drivers/ata/pata_cs5530.c b/drivers/ata/pata_cs5530.c
index a07cc81..981f492 100644
--- a/drivers/ata/pata_cs5530.c
+++ b/drivers/ata/pata_cs5530.c
@@ -180,6 +180,7 @@
 	.proc_name		= DRV_NAME,
 	.dma_boundary		= ATA_DMA_BOUNDARY,
 	.slave_configure	= ata_scsi_slave_config,
+	.slave_destroy		= ata_scsi_slave_destroy,
 	.bios_param		= ata_std_bios_param,
 };
 
diff --git a/drivers/ata/pata_cs5535.c b/drivers/ata/pata_cs5535.c
index f8def3f..8dafa4a 100644
--- a/drivers/ata/pata_cs5535.c
+++ b/drivers/ata/pata_cs5535.c
@@ -184,6 +184,7 @@
 	.proc_name		= DRV_NAME,
 	.dma_boundary		= ATA_DMA_BOUNDARY,
 	.slave_configure	= ata_scsi_slave_config,
+	.slave_destroy		= ata_scsi_slave_destroy,
 	.bios_param		= ata_std_bios_param,
 };
 
diff --git a/drivers/ata/pata_cypress.c b/drivers/ata/pata_cypress.c
index 247b436..5a0b811 100644
--- a/drivers/ata/pata_cypress.c
+++ b/drivers/ata/pata_cypress.c
@@ -135,6 +135,7 @@
 	.proc_name		= DRV_NAME,
 	.dma_boundary		= ATA_DMA_BOUNDARY,
 	.slave_configure	= ata_scsi_slave_config,
+	.slave_destroy		= ata_scsi_slave_destroy,
 	.bios_param		= ata_std_bios_param,
 };
 
diff --git a/drivers/ata/pata_efar.c b/drivers/ata/pata_efar.c
index ef18c60..755f792 100644
--- a/drivers/ata/pata_efar.c
+++ b/drivers/ata/pata_efar.c
@@ -233,6 +233,7 @@
 	.proc_name		= DRV_NAME,
 	.dma_boundary		= ATA_DMA_BOUNDARY,
 	.slave_configure	= ata_scsi_slave_config,
+	.slave_destroy		= ata_scsi_slave_destroy,
 	.bios_param		= ata_std_bios_param,
 };
 
diff --git a/drivers/ata/pata_hpt366.c b/drivers/ata/pata_hpt366.c
index 6d3e4c0..c0e150a9 100644
--- a/drivers/ata/pata_hpt366.c
+++ b/drivers/ata/pata_hpt366.c
@@ -329,6 +329,7 @@
 	.proc_name		= DRV_NAME,
 	.dma_boundary		= ATA_DMA_BOUNDARY,
 	.slave_configure	= ata_scsi_slave_config,
+	.slave_destroy		= ata_scsi_slave_destroy,
 	.bios_param		= ata_std_bios_param,
 };
 
diff --git a/drivers/ata/pata_hpt37x.c b/drivers/ata/pata_hpt37x.c
index fce3fcd..1eeb16f 100644
--- a/drivers/ata/pata_hpt37x.c
+++ b/drivers/ata/pata_hpt37x.c
@@ -775,6 +775,7 @@
 	.proc_name		= DRV_NAME,
 	.dma_boundary		= ATA_DMA_BOUNDARY,
 	.slave_configure	= ata_scsi_slave_config,
+	.slave_destroy		= ata_scsi_slave_destroy,
 	.bios_param		= ata_std_bios_param,
 };
 
diff --git a/drivers/ata/pata_hpt3x2n.c b/drivers/ata/pata_hpt3x2n.c
index 58cfb2b..47d7664 100644
--- a/drivers/ata/pata_hpt3x2n.c
+++ b/drivers/ata/pata_hpt3x2n.c
@@ -341,6 +341,7 @@
 	.proc_name		= DRV_NAME,
 	.dma_boundary		= ATA_DMA_BOUNDARY,
 	.slave_configure	= ata_scsi_slave_config,
+	.slave_destroy		= ata_scsi_slave_destroy,
 	.bios_param		= ata_std_bios_param,
 };
 
diff --git a/drivers/ata/pata_hpt3x3.c b/drivers/ata/pata_hpt3x3.c
index 3334d72..d216cc5 100644
--- a/drivers/ata/pata_hpt3x3.c
+++ b/drivers/ata/pata_hpt3x3.c
@@ -118,6 +118,7 @@
 	.proc_name		= DRV_NAME,
 	.dma_boundary		= ATA_DMA_BOUNDARY,
 	.slave_configure	= ata_scsi_slave_config,
+	.slave_destroy		= ata_scsi_slave_destroy,
 	.bios_param		= ata_std_bios_param,
 };
 
diff --git a/drivers/ata/pata_isapnp.c b/drivers/ata/pata_isapnp.c
index 640b8b0..40ca2b8 100644
--- a/drivers/ata/pata_isapnp.c
+++ b/drivers/ata/pata_isapnp.c
@@ -34,6 +34,7 @@
 	.proc_name		= DRV_NAME,
 	.dma_boundary		= ATA_DMA_BOUNDARY,
 	.slave_configure	= ata_scsi_slave_config,
+	.slave_destroy		= ata_scsi_slave_destroy,
 	.bios_param		= ata_std_bios_param,
 };
 
diff --git a/drivers/ata/pata_it821x.c b/drivers/ata/pata_it821x.c
index 18ff3e5..7f68f14 100644
--- a/drivers/ata/pata_it821x.c
+++ b/drivers/ata/pata_it821x.c
@@ -675,6 +675,7 @@
 	.proc_name		= DRV_NAME,
 	.dma_boundary		= ATA_DMA_BOUNDARY,
 	.slave_configure	= ata_scsi_slave_config,
+	.slave_destroy		= ata_scsi_slave_destroy,
 	.bios_param		= ata_std_bios_param,
 };
 
diff --git a/drivers/ata/pata_jmicron.c b/drivers/ata/pata_jmicron.c
index 52a2bdf..0210b10 100644
--- a/drivers/ata/pata_jmicron.c
+++ b/drivers/ata/pata_jmicron.c
@@ -136,6 +136,7 @@
 	.proc_name		= DRV_NAME,
 	.dma_boundary		= ATA_DMA_BOUNDARY,
 	.slave_configure	= ata_scsi_slave_config,
+	.slave_destroy		= ata_scsi_slave_destroy,
 	/* Use standard CHS mapping rules */
 	.bios_param		= ata_std_bios_param,
 };
diff --git a/drivers/ata/pata_legacy.c b/drivers/ata/pata_legacy.c
index 10231ef..b39078b 100644
--- a/drivers/ata/pata_legacy.c
+++ b/drivers/ata/pata_legacy.c
@@ -135,6 +135,7 @@
 	.proc_name		= DRV_NAME,
 	.dma_boundary		= ATA_DMA_BOUNDARY,
 	.slave_configure	= ata_scsi_slave_config,
+	.slave_destroy		= ata_scsi_slave_destroy,
 	.bios_param		= ata_std_bios_param,
 };
 
diff --git a/drivers/ata/pata_mpiix.c b/drivers/ata/pata_mpiix.c
index 9dfe3e9..e00d406 100644
--- a/drivers/ata/pata_mpiix.c
+++ b/drivers/ata/pata_mpiix.c
@@ -166,6 +166,7 @@
 	.proc_name		= DRV_NAME,
 	.dma_boundary		= ATA_DMA_BOUNDARY,
 	.slave_configure	= ata_scsi_slave_config,
+	.slave_destroy		= ata_scsi_slave_destroy,
 	.bios_param		= ata_std_bios_param,
 };
 
diff --git a/drivers/ata/pata_netcell.c b/drivers/ata/pata_netcell.c
index f5672de..1963a4d 100644
--- a/drivers/ata/pata_netcell.c
+++ b/drivers/ata/pata_netcell.c
@@ -62,6 +62,7 @@
 	.proc_name		= DRV_NAME,
 	.dma_boundary		= ATA_DMA_BOUNDARY,
 	.slave_configure	= ata_scsi_slave_config,
+	.slave_destroy		= ata_scsi_slave_destroy,
 	/* Use standard CHS mapping rules */
 	.bios_param		= ata_std_bios_param,
 };
diff --git a/drivers/ata/pata_ns87410.c b/drivers/ata/pata_ns87410.c
index 2a3dbee..7ec800f 100644
--- a/drivers/ata/pata_ns87410.c
+++ b/drivers/ata/pata_ns87410.c
@@ -156,6 +156,7 @@
 	.proc_name		= DRV_NAME,
 	.dma_boundary		= ATA_DMA_BOUNDARY,
 	.slave_configure	= ata_scsi_slave_config,
+	.slave_destroy		= ata_scsi_slave_destroy,
 	.bios_param		= ata_std_bios_param,
 };
 
diff --git a/drivers/ata/pata_oldpiix.c b/drivers/ata/pata_oldpiix.c
index fc947df..8837256 100644
--- a/drivers/ata/pata_oldpiix.c
+++ b/drivers/ata/pata_oldpiix.c
@@ -231,6 +231,7 @@
 	.proc_name		= DRV_NAME,
 	.dma_boundary		= ATA_DMA_BOUNDARY,
 	.slave_configure	= ata_scsi_slave_config,
+	.slave_destroy		= ata_scsi_slave_destroy,
 	.bios_param		= ata_std_bios_param,
 };
 
diff --git a/drivers/ata/pata_opti.c b/drivers/ata/pata_opti.c
index a7320ba..c6319cf 100644
--- a/drivers/ata/pata_opti.c
+++ b/drivers/ata/pata_opti.c
@@ -202,6 +202,7 @@
 	.proc_name		= DRV_NAME,
 	.dma_boundary		= ATA_DMA_BOUNDARY,
 	.slave_configure	= ata_scsi_slave_config,
+	.slave_destroy		= ata_scsi_slave_destroy,
 	.bios_param		= ata_std_bios_param,
 };
 
diff --git a/drivers/ata/pata_optidma.c b/drivers/ata/pata_optidma.c
index c6906b4..2f4770c 100644
--- a/drivers/ata/pata_optidma.c
+++ b/drivers/ata/pata_optidma.c
@@ -359,6 +359,7 @@
 	.proc_name		= DRV_NAME,
 	.dma_boundary		= ATA_DMA_BOUNDARY,
 	.slave_configure	= ata_scsi_slave_config,
+	.slave_destroy		= ata_scsi_slave_destroy,
 	.bios_param		= ata_std_bios_param,
 };
 
diff --git a/drivers/ata/pata_pcmcia.c b/drivers/ata/pata_pcmcia.c
index e93ea27..999922d 100644
--- a/drivers/ata/pata_pcmcia.c
+++ b/drivers/ata/pata_pcmcia.c
@@ -69,6 +69,7 @@
 	.proc_name		= DRV_NAME,
 	.dma_boundary		= ATA_DMA_BOUNDARY,
 	.slave_configure	= ata_scsi_slave_config,
+	.slave_destroy		= ata_scsi_slave_destroy,
 	.bios_param		= ata_std_bios_param,
 };
 
diff --git a/drivers/ata/pata_pdc2027x.c b/drivers/ata/pata_pdc2027x.c
index d894d99..beb6d10 100644
--- a/drivers/ata/pata_pdc2027x.c
+++ b/drivers/ata/pata_pdc2027x.c
@@ -141,6 +141,7 @@
 	.proc_name		= DRV_NAME,
 	.dma_boundary		= ATA_DMA_BOUNDARY,
 	.slave_configure	= ata_scsi_slave_config,
+	.slave_destroy		= ata_scsi_slave_destroy,
 	.bios_param		= ata_std_bios_param,
 };
 
diff --git a/drivers/ata/pata_pdc202xx_old.c b/drivers/ata/pata_pdc202xx_old.c
index 5ba9eb2..6baf51b 100644
--- a/drivers/ata/pata_pdc202xx_old.c
+++ b/drivers/ata/pata_pdc202xx_old.c
@@ -269,6 +269,7 @@
 	.proc_name		= DRV_NAME,
 	.dma_boundary		= ATA_DMA_BOUNDARY,
 	.slave_configure	= ata_scsi_slave_config,
+	.slave_destroy		= ata_scsi_slave_destroy,
 	.bios_param		= ata_std_bios_param,
 };
 
diff --git a/drivers/ata/pata_qdi.c b/drivers/ata/pata_qdi.c
index 2c3cc0c..314938d 100644
--- a/drivers/ata/pata_qdi.c
+++ b/drivers/ata/pata_qdi.c
@@ -164,6 +164,7 @@
 	.proc_name		= DRV_NAME,
 	.dma_boundary		= ATA_DMA_BOUNDARY,
 	.slave_configure	= ata_scsi_slave_config,
+	.slave_destroy		= ata_scsi_slave_destroy,
 	.bios_param		= ata_std_bios_param,
 };
 
diff --git a/drivers/ata/pata_radisys.c b/drivers/ata/pata_radisys.c
index 1af83d7..048c2bb 100644
--- a/drivers/ata/pata_radisys.c
+++ b/drivers/ata/pata_radisys.c
@@ -227,6 +227,7 @@
 	.proc_name		= DRV_NAME,
 	.dma_boundary		= ATA_DMA_BOUNDARY,
 	.slave_configure	= ata_scsi_slave_config,
+	.slave_destroy		= ata_scsi_slave_destroy,
 	.bios_param		= ata_std_bios_param,
 };
 
diff --git a/drivers/ata/pata_rz1000.c b/drivers/ata/pata_rz1000.c
index 4533b63..e4e5ea4 100644
--- a/drivers/ata/pata_rz1000.c
+++ b/drivers/ata/pata_rz1000.c
@@ -90,6 +90,7 @@
 	.proc_name		= DRV_NAME,
 	.dma_boundary		= ATA_DMA_BOUNDARY,
 	.slave_configure	= ata_scsi_slave_config,
+	.slave_destroy		= ata_scsi_slave_destroy,
 	.bios_param		= ata_std_bios_param,
 };
 
diff --git a/drivers/ata/pata_sc1200.c b/drivers/ata/pata_sc1200.c
index 067d9d2..0c75dae 100644
--- a/drivers/ata/pata_sc1200.c
+++ b/drivers/ata/pata_sc1200.c
@@ -193,6 +193,7 @@
 	.proc_name		= DRV_NAME,
 	.dma_boundary		= ATA_DMA_BOUNDARY,
 	.slave_configure	= ata_scsi_slave_config,
+	.slave_destroy		= ata_scsi_slave_destroy,
 	.bios_param		= ata_std_bios_param,
 };
 
diff --git a/drivers/ata/pata_serverworks.c b/drivers/ata/pata_serverworks.c
index 5bbf76e..be7f60e 100644
--- a/drivers/ata/pata_serverworks.c
+++ b/drivers/ata/pata_serverworks.c
@@ -325,6 +325,7 @@
 	.proc_name		= DRV_NAME,
 	.dma_boundary		= ATA_DMA_BOUNDARY,
 	.slave_configure	= ata_scsi_slave_config,
+	.slave_destroy		= ata_scsi_slave_destroy,
 	.bios_param		= ata_std_bios_param,
 };
 
diff --git a/drivers/ata/pata_sil680.c b/drivers/ata/pata_sil680.c
index 4a2b72b..11942fd 100644
--- a/drivers/ata/pata_sil680.c
+++ b/drivers/ata/pata_sil680.c
@@ -225,6 +225,7 @@
 	.proc_name		= DRV_NAME,
 	.dma_boundary		= ATA_DMA_BOUNDARY,
 	.slave_configure	= ata_scsi_slave_config,
+	.slave_destroy		= ata_scsi_slave_destroy,
 	.bios_param		= ata_std_bios_param,
 };
 
diff --git a/drivers/ata/pata_sis.c b/drivers/ata/pata_sis.c
index b9ffafb..91e85f9 100644
--- a/drivers/ata/pata_sis.c
+++ b/drivers/ata/pata_sis.c
@@ -545,6 +545,7 @@
 	.proc_name		= DRV_NAME,
 	.dma_boundary		= ATA_DMA_BOUNDARY,
 	.slave_configure	= ata_scsi_slave_config,
+	.slave_destroy		= ata_scsi_slave_destroy,
 	.bios_param		= ata_std_bios_param,
 };
 
diff --git a/drivers/ata/pata_sl82c105.c b/drivers/ata/pata_sl82c105.c
index 08a6dc8..dc1cfc6 100644
--- a/drivers/ata/pata_sl82c105.c
+++ b/drivers/ata/pata_sl82c105.c
@@ -237,6 +237,7 @@
 	.proc_name		= DRV_NAME,
 	.dma_boundary		= ATA_DMA_BOUNDARY,
 	.slave_configure	= ata_scsi_slave_config,
+	.slave_destroy		= ata_scsi_slave_destroy,
 	.bios_param		= ata_std_bios_param,
 };
 
diff --git a/drivers/ata/pata_triflex.c b/drivers/ata/pata_triflex.c
index 9640f80..bfda1f7 100644
--- a/drivers/ata/pata_triflex.c
+++ b/drivers/ata/pata_triflex.c
@@ -192,6 +192,7 @@
 	.proc_name		= DRV_NAME,
 	.dma_boundary		= ATA_DMA_BOUNDARY,
 	.slave_configure	= ata_scsi_slave_config,
+	.slave_destroy		= ata_scsi_slave_destroy,
 	.bios_param		= ata_std_bios_param,
 };
 
diff --git a/drivers/ata/pata_via.c b/drivers/ata/pata_via.c
index 1e7be9e..c5f1616 100644
--- a/drivers/ata/pata_via.c
+++ b/drivers/ata/pata_via.c
@@ -295,6 +295,7 @@
 	.proc_name		= DRV_NAME,
 	.dma_boundary		= ATA_DMA_BOUNDARY,
 	.slave_configure	= ata_scsi_slave_config,
+	.slave_destroy		= ata_scsi_slave_destroy,
 	.bios_param		= ata_std_bios_param,
 };
 
diff --git a/drivers/atm/iphase.c b/drivers/atm/iphase.c
index 9ed1c60..bb7ef57 100644
--- a/drivers/atm/iphase.c
+++ b/drivers/atm/iphase.c
@@ -305,7 +305,7 @@
 **  |  R | NZ |  5-bit exponent  |        9-bit mantissa         |
 **  +----+----+------------------+-------------------------------+
 ** 
-**    R = reserverd (written as 0)
+**    R = reserved (written as 0)
 **    NZ = 0 if 0 cells/sec; 1 otherwise
 **
 **    if NZ = 1, rate = 1.mmmmmmmmm x 2^(eeeee) cells/sec
diff --git a/drivers/base/bus.c b/drivers/base/bus.c
index 7d8a7ce..472810f 100644
--- a/drivers/base/bus.c
+++ b/drivers/base/bus.c
@@ -355,6 +355,21 @@
 	}
 }
 
+#ifdef CONFIG_SYSFS_DEPRECATED
+static int make_deprecated_bus_links(struct device *dev)
+{
+	return sysfs_create_link(&dev->kobj,
+				 &dev->bus->subsys.kset.kobj, "bus");
+}
+
+static void remove_deprecated_bus_links(struct device *dev)
+{
+	sysfs_remove_link(&dev->kobj, "bus");
+}
+#else
+static inline int make_deprecated_bus_links(struct device *dev) { return 0; }
+static inline void remove_deprecated_bus_links(struct device *dev) { }
+#endif
 
 /**
  *	bus_add_device - add device to bus
@@ -381,8 +396,7 @@
 				&dev->bus->subsys.kset.kobj, "subsystem");
 		if (error)
 			goto out_subsys;
-		error = sysfs_create_link(&dev->kobj,
-				&dev->bus->subsys.kset.kobj, "bus");
+		error = make_deprecated_bus_links(dev);
 		if (error)
 			goto out_deprecated;
 	}
@@ -436,7 +450,7 @@
 {
 	if (dev->bus) {
 		sysfs_remove_link(&dev->kobj, "subsystem");
-		sysfs_remove_link(&dev->kobj, "bus");
+		remove_deprecated_bus_links(dev);
 		sysfs_remove_link(&dev->bus->devices.kobj, dev->bus_id);
 		device_remove_attrs(dev->bus, dev);
 		if (dev->is_registered) {
@@ -724,6 +738,8 @@
 {
 	int retval;
 
+	BLOCKING_INIT_NOTIFIER_HEAD(&bus->bus_notifier);
+
 	retval = kobject_set_name(&bus->subsys.kset.kobj, "%s", bus->name);
 	if (retval)
 		goto out;
@@ -782,6 +798,18 @@
 	subsystem_unregister(&bus->subsys);
 }
 
+int bus_register_notifier(struct bus_type *bus, struct notifier_block *nb)
+{
+	return blocking_notifier_chain_register(&bus->bus_notifier, nb);
+}
+EXPORT_SYMBOL_GPL(bus_register_notifier);
+
+int bus_unregister_notifier(struct bus_type *bus, struct notifier_block *nb)
+{
+	return blocking_notifier_chain_unregister(&bus->bus_notifier, nb);
+}
+EXPORT_SYMBOL_GPL(bus_unregister_notifier);
+
 int __init buses_init(void)
 {
 	return subsystem_register(&bus_subsys);
diff --git a/drivers/base/class.c b/drivers/base/class.c
index 0ff267a..f098881 100644
--- a/drivers/base/class.c
+++ b/drivers/base/class.c
@@ -352,6 +352,92 @@
 	return class_dev->class->name;
 }
 
+#ifdef CONFIG_SYSFS_DEPRECATED
+char *make_class_name(const char *name, struct kobject *kobj)
+{
+	char *class_name;
+	int size;
+
+	size = strlen(name) + strlen(kobject_name(kobj)) + 2;
+
+	class_name = kmalloc(size, GFP_KERNEL);
+	if (!class_name)
+		return ERR_PTR(-ENOMEM);
+
+	strcpy(class_name, name);
+	strcat(class_name, ":");
+	strcat(class_name, kobject_name(kobj));
+	return class_name;
+}
+
+static int deprecated_class_uevent(char **envp, int num_envp, int *cur_index,
+				   char *buffer, int buffer_size,
+				   int *cur_len,
+				   struct class_device *class_dev)
+{
+	struct device *dev = class_dev->dev;
+	char *path;
+
+	if (!dev)
+		return 0;
+
+	/* add device, backing this class device (deprecated) */
+	path = kobject_get_path(&dev->kobj, GFP_KERNEL);
+
+	add_uevent_var(envp, num_envp, cur_index, buffer, buffer_size,
+		       cur_len, "PHYSDEVPATH=%s", path);
+	kfree(path);
+
+	if (dev->bus)
+		add_uevent_var(envp, num_envp, cur_index,
+			       buffer, buffer_size, cur_len,
+			       "PHYSDEVBUS=%s", dev->bus->name);
+
+	if (dev->driver)
+		add_uevent_var(envp, num_envp, cur_index,
+			       buffer, buffer_size, cur_len,
+			       "PHYSDEVDRIVER=%s", dev->driver->name);
+	return 0;
+}
+
+static int make_deprecated_class_device_links(struct class_device *class_dev)
+{
+	char *class_name;
+	int error;
+
+	if (!class_dev->dev)
+		return 0;
+
+	class_name = make_class_name(class_dev->class->name, &class_dev->kobj);
+	error = sysfs_create_link(&class_dev->dev->kobj, &class_dev->kobj,
+				  class_name);
+	kfree(class_name);
+	return error;
+}
+
+static void remove_deprecated_class_device_links(struct class_device *class_dev)
+{
+	char *class_name;
+
+	if (!class_dev->dev)
+		return;
+
+	class_name = make_class_name(class_dev->class->name, &class_dev->kobj);
+	sysfs_remove_link(&class_dev->dev->kobj, class_name);
+	kfree(class_name);
+}
+#else
+static inline int deprecated_class_uevent(char **envp, int num_envp,
+					  int *cur_index, char *buffer,
+					  int buffer_size, int *cur_len,
+					  struct class_device *class_dev)
+{ return 0; }
+static inline int make_deprecated_class_device_links(struct class_device *cd)
+{ return 0; }
+static void remove_deprecated_class_device_links(struct class_device *cd)
+{ }
+#endif
+
 static int class_uevent(struct kset *kset, struct kobject *kobj, char **envp,
 			 int num_envp, char *buffer, int buffer_size)
 {
@@ -362,25 +448,8 @@
 
 	pr_debug("%s - name = %s\n", __FUNCTION__, class_dev->class_id);
 
-	if (class_dev->dev) {
-		/* add device, backing this class device (deprecated) */
-		struct device *dev = class_dev->dev;
-		char *path = kobject_get_path(&dev->kobj, GFP_KERNEL);
-
-		add_uevent_var(envp, num_envp, &i, buffer, buffer_size,
-			       &length, "PHYSDEVPATH=%s", path);
-		kfree(path);
-
-		if (dev->bus)
-			add_uevent_var(envp, num_envp, &i,
-				       buffer, buffer_size, &length,
-				       "PHYSDEVBUS=%s", dev->bus->name);
-
-		if (dev->driver)
-			add_uevent_var(envp, num_envp, &i,
-				       buffer, buffer_size, &length,
-				       "PHYSDEVDRIVER=%s", dev->driver->name);
-	}
+	deprecated_class_uevent(envp, num_envp, &i, buffer, buffer_size,
+				&length, class_dev);
 
 	if (MAJOR(class_dev->devt)) {
 		add_uevent_var(envp, num_envp, &i,
@@ -506,29 +575,11 @@
 	INIT_LIST_HEAD(&class_dev->node);
 }
 
-char *make_class_name(const char *name, struct kobject *kobj)
-{
-	char *class_name;
-	int size;
-
-	size = strlen(name) + strlen(kobject_name(kobj)) + 2;
-
-	class_name = kmalloc(size, GFP_KERNEL);
-	if (!class_name)
-		return ERR_PTR(-ENOMEM);
-
-	strcpy(class_name, name);
-	strcat(class_name, ":");
-	strcat(class_name, kobject_name(kobj));
-	return class_name;
-}
-
 int class_device_add(struct class_device *class_dev)
 {
 	struct class *parent_class = NULL;
 	struct class_device *parent_class_dev = NULL;
 	struct class_interface *class_intf;
-	char *class_name = NULL;
 	int error = -EINVAL;
 
 	class_dev = class_device_get(class_dev);
@@ -599,20 +650,18 @@
 		goto out5;
 
 	if (class_dev->dev) {
-		class_name = make_class_name(class_dev->class->name,
-					     &class_dev->kobj);
 		error = sysfs_create_link(&class_dev->kobj,
 					  &class_dev->dev->kobj, "device");
 		if (error)
 			goto out6;
-		error = sysfs_create_link(&class_dev->dev->kobj, &class_dev->kobj,
-					  class_name);
-		if (error)
-			goto out7;
 	}
 
 	error = class_device_add_groups(class_dev);
 	if (error)
+		goto out7;
+
+	error = make_deprecated_class_device_links(class_dev);
+	if (error)
 		goto out8;
 
 	kobject_uevent(&class_dev->kobj, KOBJ_ADD);
@@ -629,8 +678,7 @@
 	goto out1;
 
  out8:
-	if (class_dev->dev)
-		sysfs_remove_link(&class_dev->kobj, class_name);
+	class_device_remove_groups(class_dev);
  out7:
 	if (class_dev->dev)
 		sysfs_remove_link(&class_dev->kobj, "device");
@@ -649,7 +697,6 @@
 	class_put(parent_class);
  out1:
 	class_device_put(class_dev);
-	kfree(class_name);
 	return error;
 }
 
@@ -726,7 +773,6 @@
 	struct class *parent_class = class_dev->class;
 	struct class_device *parent_device = class_dev->parent;
 	struct class_interface *class_intf;
-	char *class_name = NULL;
 
 	if (parent_class) {
 		down(&parent_class->sem);
@@ -738,10 +784,8 @@
 	}
 
 	if (class_dev->dev) {
-		class_name = make_class_name(class_dev->class->name,
-					     &class_dev->kobj);
+		remove_deprecated_class_device_links(class_dev);
 		sysfs_remove_link(&class_dev->kobj, "device");
-		sysfs_remove_link(&class_dev->dev->kobj, class_name);
 	}
 	sysfs_remove_link(&class_dev->kobj, "subsystem");
 	class_device_remove_file(class_dev, &class_dev->uevent_attr);
@@ -755,7 +799,6 @@
 
 	class_device_put(parent_device);
 	class_put(parent_class);
-	kfree(class_name);
 }
 
 void class_device_unregister(struct class_device *class_dev)
@@ -804,14 +847,17 @@
 	pr_debug("CLASS: renaming '%s' to '%s'\n", class_dev->class_id,
 		 new_name);
 
+#ifdef CONFIG_SYSFS_DEPRECATED
 	if (class_dev->dev)
 		old_class_name = make_class_name(class_dev->class->name,
 						 &class_dev->kobj);
+#endif
 
 	strlcpy(class_dev->class_id, new_name, KOBJ_NAME_LEN);
 
 	error = kobject_rename(&class_dev->kobj, new_name);
 
+#ifdef CONFIG_SYSFS_DEPRECATED
 	if (class_dev->dev) {
 		new_class_name = make_class_name(class_dev->class->name,
 						 &class_dev->kobj);
@@ -819,6 +865,7 @@
 				  new_class_name);
 		sysfs_remove_link(&class_dev->dev->kobj, old_class_name);
 	}
+#endif
 	class_device_put(class_dev);
 
 	kfree(old_class_name);
@@ -893,23 +940,6 @@
 	class_put(parent);
 }
 
-int virtual_device_parent(struct device *dev)
-{
-	if (!dev->class)
-		return -ENODEV;
-
-	if (!dev->class->virtual_dir) {
-		static struct kobject *virtual_dir = NULL;
-
-		if (!virtual_dir)
-			virtual_dir = kobject_add_dir(&devices_subsys.kset.kobj, "virtual");
-		dev->class->virtual_dir = kobject_add_dir(virtual_dir, dev->class->name);
-	}
-
-	dev->kobj.parent = dev->class->virtual_dir;
-	return 0;
-}
-
 int __init classes_init(void)
 {
 	int retval;
diff --git a/drivers/base/core.c b/drivers/base/core.c
index 002fde4..e4b530e 100644
--- a/drivers/base/core.c
+++ b/drivers/base/core.c
@@ -17,6 +17,7 @@
 #include <linux/slab.h>
 #include <linux/string.h>
 #include <linux/kdev_t.h>
+#include <linux/notifier.h>
 
 #include <asm/semaphore.h>
 
@@ -153,20 +154,24 @@
 			       "MINOR=%u", MINOR(dev->devt));
 	}
 
+#ifdef CONFIG_SYSFS_DEPRECATED
 	/* add bus name (same as SUBSYSTEM, deprecated) */
 	if (dev->bus)
 		add_uevent_var(envp, num_envp, &i,
 			       buffer, buffer_size, &length,
 			       "PHYSDEVBUS=%s", dev->bus->name);
+#endif
 
 	/* add driver name (PHYSDEV* values are deprecated)*/
 	if (dev->driver) {
 		add_uevent_var(envp, num_envp, &i,
 			       buffer, buffer_size, &length,
 			       "DRIVER=%s", dev->driver->name);
+#ifdef CONFIG_SYSFS_DEPRECATED
 		add_uevent_var(envp, num_envp, &i,
 			       buffer, buffer_size, &length,
 			       "PHYSDEVDRIVER=%s", dev->driver->name);
+#endif
 	}
 
 	/* terminate, set to next free slot, shrink available space */
@@ -383,6 +388,52 @@
 	device_init_wakeup(dev, 0);
 }
 
+#ifdef CONFIG_SYSFS_DEPRECATED
+static int setup_parent(struct device *dev, struct device *parent)
+{
+	/* Set the parent to the class, not the parent device */
+	/* this keeps sysfs from having a symlink to make old udevs happy */
+	if (dev->class)
+		dev->kobj.parent = &dev->class->subsys.kset.kobj;
+	else if (parent)
+		dev->kobj.parent = &parent->kobj;
+
+	return 0;
+}
+#else
+static int virtual_device_parent(struct device *dev)
+{
+	if (!dev->class)
+		return -ENODEV;
+
+	if (!dev->class->virtual_dir) {
+		static struct kobject *virtual_dir = NULL;
+
+		if (!virtual_dir)
+			virtual_dir = kobject_add_dir(&devices_subsys.kset.kobj, "virtual");
+		dev->class->virtual_dir = kobject_add_dir(virtual_dir, dev->class->name);
+	}
+
+	dev->kobj.parent = dev->class->virtual_dir;
+	return 0;
+}
+
+static int setup_parent(struct device *dev, struct device *parent)
+{
+	int error;
+
+	/* if this is a class device, and has no parent, create one */
+	if ((dev->class) && (parent == NULL)) {
+		error = virtual_device_parent(dev);
+		if (error)
+			return error;
+	} else if (parent)
+		dev->kobj.parent = &parent->kobj;
+
+	return 0;
+}
+#endif
+
 /**
  *	device_add - add device to device hierarchy.
  *	@dev:	device.
@@ -405,29 +456,29 @@
 	if (!dev || !strlen(dev->bus_id))
 		goto Error;
 
-	/* if this is a class device, and has no parent, create one */
-	if ((dev->class) && (dev->parent == NULL)) {
-		error = virtual_device_parent(dev);
-		if (error)
-			goto Error;
-	}
+	pr_debug("DEV: registering device: ID = '%s'\n", dev->bus_id);
 
 	parent = get_device(dev->parent);
 
-	pr_debug("DEV: registering device: ID = '%s'\n", dev->bus_id);
+	error = setup_parent(dev, parent);
+	if (error)
+		goto Error;
 
 	/* first, register with generic layer. */
 	kobject_set_name(&dev->kobj, "%s", dev->bus_id);
-	if (parent)
-		dev->kobj.parent = &parent->kobj;
-
-	if ((error = kobject_add(&dev->kobj)))
+	error = kobject_add(&dev->kobj);
+	if (error)
 		goto Error;
 
 	/* notify platform of device entry */
 	if (platform_notify)
 		platform_notify(dev);
 
+	/* notify clients of device entry (new way) */
+	if (dev->bus)
+		blocking_notifier_call_chain(&dev->bus->bus_notifier,
+					     BUS_NOTIFY_ADD_DEVICE, dev);
+
 	dev->uevent_attr.attr.name = "uevent";
 	dev->uevent_attr.attr.mode = S_IWUSR;
 	if (dev->driver)
@@ -461,13 +512,18 @@
 	if (dev->class) {
 		sysfs_create_link(&dev->kobj, &dev->class->subsys.kset.kobj,
 				  "subsystem");
-		sysfs_create_link(&dev->class->subsys.kset.kobj, &dev->kobj,
-				  dev->bus_id);
+		/* If this is not a "fake" compatible device, then create the
+		 * symlink from the class to the device. */
+		if (dev->kobj.parent != &dev->class->subsys.kset.kobj)
+			sysfs_create_link(&dev->class->subsys.kset.kobj,
+					  &dev->kobj, dev->bus_id);
+#ifdef CONFIG_SYSFS_DEPRECATED
 		if (parent) {
 			sysfs_create_link(&dev->kobj, &dev->parent->kobj, "device");
 			class_name = make_class_name(dev->class->name, &dev->kobj);
 			sysfs_create_link(&dev->parent->kobj, &dev->kobj, class_name);
 		}
+#endif
 	}
 
 	if ((error = device_add_attrs(dev)))
@@ -504,6 +560,9 @@
  BusError:
 	device_pm_remove(dev);
  PMError:
+	if (dev->bus)
+		blocking_notifier_call_chain(&dev->bus->bus_notifier,
+					     BUS_NOTIFY_DEL_DEVICE, dev);
 	device_remove_groups(dev);
  GroupError:
  	device_remove_attrs(dev);
@@ -586,7 +645,6 @@
 void device_del(struct device * dev)
 {
 	struct device * parent = dev->parent;
-	char *class_name = NULL;
 	struct class_interface *class_intf;
 
 	if (parent)
@@ -597,13 +655,21 @@
 	}
 	if (dev->class) {
 		sysfs_remove_link(&dev->kobj, "subsystem");
-		sysfs_remove_link(&dev->class->subsys.kset.kobj, dev->bus_id);
-		class_name = make_class_name(dev->class->name, &dev->kobj);
+		/* If this is not a "fake" compatible device, remove the
+		 * symlink from the class to the device. */
+		if (dev->kobj.parent != &dev->class->subsys.kset.kobj)
+			sysfs_remove_link(&dev->class->subsys.kset.kobj,
+					  dev->bus_id);
+#ifdef CONFIG_SYSFS_DEPRECATED
 		if (parent) {
-			sysfs_remove_link(&dev->kobj, "device");
+			char *class_name = make_class_name(dev->class->name,
+							   &dev->kobj);
 			sysfs_remove_link(&dev->parent->kobj, class_name);
+			kfree(class_name);
+			sysfs_remove_link(&dev->kobj, "device");
 		}
-		kfree(class_name);
+#endif
+
 		down(&dev->class->sem);
 		/* notify any interfaces that the device is now gone */
 		list_for_each_entry(class_intf, &dev->class->interfaces, node)
@@ -616,13 +682,16 @@
 	device_remove_file(dev, &dev->uevent_attr);
 	device_remove_groups(dev);
 	device_remove_attrs(dev);
+	bus_remove_device(dev);
 
 	/* Notify the platform of the removal, in case they
 	 * need to do anything...
 	 */
 	if (platform_notify_remove)
 		platform_notify_remove(dev);
-	bus_remove_device(dev);
+	if (dev->bus)
+		blocking_notifier_call_chain(&dev->bus->bus_notifier,
+					     BUS_NOTIFY_DEL_DEVICE, dev);
 	device_pm_remove(dev);
 	kobject_uevent(&dev->kobj, KOBJ_REMOVE);
 	kobject_del(&dev->kobj);
@@ -681,12 +750,45 @@
 	return error;
 }
 
+/**
+ * device_find_child - device iterator for locating a particular device.
+ * @parent: parent struct device
+ * @data: Data to pass to match function
+ * @match: Callback function to check device
+ *
+ * This is similar to the device_for_each_child() function above, but it
+ * returns a reference to a device that is 'found' for later use, as
+ * determined by the @match callback.
+ *
+ * The callback should return 0 if the device doesn't match and non-zero
+ * if it does.  If the callback returns non-zero and a reference to the
+ * current device can be obtained, this function will return to the caller
+ * and not iterate over any more devices.
+ */
+struct device * device_find_child(struct device *parent, void *data,
+				  int (*match)(struct device *, void *))
+{
+	struct klist_iter i;
+	struct device *child;
+
+	if (!parent)
+		return NULL;
+
+	klist_iter_init(&parent->klist_children, &i);
+	while ((child = next_device(&i)))
+		if (match(child, data) && get_device(child))
+			break;
+	klist_iter_exit(&i);
+	return child;
+}
+
 int __init devices_init(void)
 {
 	return subsystem_register(&devices_subsys);
 }
 
 EXPORT_SYMBOL_GPL(device_for_each_child);
+EXPORT_SYMBOL_GPL(device_find_child);
 
 EXPORT_SYMBOL_GPL(device_initialize);
 EXPORT_SYMBOL_GPL(device_add);
@@ -809,8 +911,10 @@
 
 	pr_debug("DEVICE: renaming '%s' to '%s'\n", dev->bus_id, new_name);
 
+#ifdef CONFIG_SYSFS_DEPRECATED
 	if ((dev->class) && (dev->parent))
 		old_class_name = make_class_name(dev->class->name, &dev->kobj);
+#endif
 
 	if (dev->class) {
 		old_symlink_name = kmalloc(BUS_ID_SIZE, GFP_KERNEL);
@@ -825,6 +929,7 @@
 
 	error = kobject_rename(&dev->kobj, new_name);
 
+#ifdef CONFIG_SYSFS_DEPRECATED
 	if (old_class_name) {
 		new_class_name = make_class_name(dev->class->name, &dev->kobj);
 		if (new_class_name) {
@@ -833,6 +938,8 @@
 			sysfs_remove_link(&dev->parent->kobj, old_class_name);
 		}
 	}
+#endif
+
 	if (dev->class) {
 		sysfs_remove_link(&dev->class->subsys.kset.kobj,
 				  old_symlink_name);
@@ -848,3 +955,95 @@
 
 	return error;
 }
+
+
+static int device_move_class_links(struct device *dev,
+				   struct device *old_parent,
+				   struct device *new_parent)
+{
+#ifdef CONFIG_SYSFS_DEPRECATED
+	int error;
+	char *class_name;
+
+	class_name = make_class_name(dev->class->name, &dev->kobj);
+	if (!class_name) {
+		error = PTR_ERR(class_name);
+		class_name = NULL;
+		goto out;
+	}
+	if (old_parent) {
+		sysfs_remove_link(&dev->kobj, "device");
+		sysfs_remove_link(&old_parent->kobj, class_name);
+	}
+	error = sysfs_create_link(&dev->kobj, &new_parent->kobj, "device");
+	if (error)
+		goto out;
+	error = sysfs_create_link(&new_parent->kobj, &dev->kobj, class_name);
+	if (error)
+		sysfs_remove_link(&dev->kobj, "device");
+out:
+	kfree(class_name);
+	return error;
+#else
+	return 0;
+#endif
+}
+
+/**
+ * device_move - moves a device to a new parent
+ * @dev: the pointer to the struct device to be moved
+ * @new_parent: the new parent of the device
+ */
+int device_move(struct device *dev, struct device *new_parent)
+{
+	int error;
+	struct device *old_parent;
+
+	dev = get_device(dev);
+	if (!dev)
+		return -EINVAL;
+
+	if (!device_is_registered(dev)) {
+		error = -EINVAL;
+		goto out;
+	}
+	new_parent = get_device(new_parent);
+	if (!new_parent) {
+		error = -EINVAL;
+		goto out;
+	}
+	pr_debug("DEVICE: moving '%s' to '%s'\n", dev->bus_id,
+		new_parent->bus_id);
+	error = kobject_move(&dev->kobj, &new_parent->kobj);
+	if (error) {
+		put_device(new_parent);
+		goto out;
+	}
+	old_parent = dev->parent;
+	dev->parent = new_parent;
+	if (old_parent)
+		klist_remove(&dev->knode_parent);
+	klist_add_tail(&dev->knode_parent, &new_parent->klist_children);
+	if (!dev->class)
+		goto out_put;
+	error = device_move_class_links(dev, old_parent, new_parent);
+	if (error) {
+		/* We ignore errors on cleanup since we're hosed anyway... */
+		device_move_class_links(dev, new_parent, old_parent);
+		if (!kobject_move(&dev->kobj, &old_parent->kobj)) {
+			klist_remove(&dev->knode_parent);
+			if (old_parent)
+				klist_add_tail(&dev->knode_parent,
+					       &old_parent->klist_children);
+		}
+		put_device(new_parent);
+		goto out;
+	}
+out_put:
+	put_device(old_parent);
+out:
+	put_device(dev);
+	return error;
+}
+
+EXPORT_SYMBOL_GPL(device_move);
diff --git a/drivers/base/dd.c b/drivers/base/dd.c
index c5d6bb4..510e788 100644
--- a/drivers/base/dd.c
+++ b/drivers/base/dd.c
@@ -26,6 +26,50 @@
 #define to_drv(node) container_of(node, struct device_driver, kobj.entry)
 
 
+static void driver_bound(struct device *dev)
+{
+	if (klist_node_attached(&dev->knode_driver)) {
+		printk(KERN_WARNING "%s: device %s already bound\n",
+			__FUNCTION__, kobject_name(&dev->kobj));
+		return;
+	}
+
+	pr_debug("bound device '%s' to driver '%s'\n",
+		 dev->bus_id, dev->driver->name);
+
+	if (dev->bus)
+		blocking_notifier_call_chain(&dev->bus->bus_notifier,
+					     BUS_NOTIFY_BOUND_DRIVER, dev);
+
+	klist_add_tail(&dev->knode_driver, &dev->driver->klist_devices);
+}
+
+static int driver_sysfs_add(struct device *dev)
+{
+	int ret;
+
+	ret = sysfs_create_link(&dev->driver->kobj, &dev->kobj,
+			  kobject_name(&dev->kobj));
+	if (ret == 0) {
+		ret = sysfs_create_link(&dev->kobj, &dev->driver->kobj,
+					"driver");
+		if (ret)
+			sysfs_remove_link(&dev->driver->kobj,
+					kobject_name(&dev->kobj));
+	}
+	return ret;
+}
+
+static void driver_sysfs_remove(struct device *dev)
+{
+	struct device_driver *drv = dev->driver;
+
+	if (drv) {
+		sysfs_remove_link(&drv->kobj, kobject_name(&dev->kobj));
+		sysfs_remove_link(&dev->kobj, "driver");
+	}
+}
+
 /**
  *	device_bind_driver - bind a driver to one device.
  *	@dev:	device.
@@ -42,27 +86,8 @@
  */
 int device_bind_driver(struct device *dev)
 {
-	int ret;
-
-	if (klist_node_attached(&dev->knode_driver)) {
-		printk(KERN_WARNING "%s: device %s already bound\n",
-			__FUNCTION__, kobject_name(&dev->kobj));
-		return 0;
-	}
-
-	pr_debug("bound device '%s' to driver '%s'\n",
-		 dev->bus_id, dev->driver->name);
-	klist_add_tail(&dev->knode_driver, &dev->driver->klist_devices);
-	ret = sysfs_create_link(&dev->driver->kobj, &dev->kobj,
-			  kobject_name(&dev->kobj));
-	if (ret == 0) {
-		ret = sysfs_create_link(&dev->kobj, &dev->driver->kobj,
-					"driver");
-		if (ret)
-			sysfs_remove_link(&dev->driver->kobj,
-					kobject_name(&dev->kobj));
-	}
-	return ret;
+	driver_bound(dev);
+	return driver_sysfs_add(dev);
 }
 
 struct stupid_thread_structure {
@@ -85,30 +110,32 @@
 		 drv->bus->name, drv->name, dev->bus_id);
 
 	dev->driver = drv;
+	if (driver_sysfs_add(dev)) {
+		printk(KERN_ERR "%s: driver_sysfs_add(%s) failed\n",
+			__FUNCTION__, dev->bus_id);
+		goto probe_failed;
+	}
+
 	if (dev->bus->probe) {
 		ret = dev->bus->probe(dev);
-		if (ret) {
-			dev->driver = NULL;
+		if (ret)
 			goto probe_failed;
-		}
 	} else if (drv->probe) {
 		ret = drv->probe(dev);
-		if (ret) {
-			dev->driver = NULL;
+		if (ret)
 			goto probe_failed;
-		}
 	}
-	if (device_bind_driver(dev)) {
-		printk(KERN_ERR "%s: device_bind_driver(%s) failed\n",
-			__FUNCTION__, dev->bus_id);
-		/* How does undo a ->probe?  We're screwed. */
-	}
+
+	driver_bound(dev);
 	ret = 1;
 	pr_debug("%s: Bound Device %s to Driver %s\n",
 		 drv->bus->name, dev->bus_id, drv->name);
 	goto done;
 
 probe_failed:
+	driver_sysfs_remove(dev);
+	dev->driver = NULL;
+
 	if (ret == -ENODEV || ret == -ENXIO) {
 		/* Driver matched, but didn't support device
 		 * or device not found.
@@ -284,10 +311,15 @@
 	drv = dev->driver;
 	if (drv) {
 		get_driver(drv);
-		sysfs_remove_link(&drv->kobj, kobject_name(&dev->kobj));
+		driver_sysfs_remove(dev);
 		sysfs_remove_link(&dev->kobj, "driver");
 		klist_remove(&dev->knode_driver);
 
+		if (dev->bus)
+			blocking_notifier_call_chain(&dev->bus->bus_notifier,
+						     BUS_NOTIFY_UNBIND_DRIVER,
+						     dev);
+
 		if (dev->bus && dev->bus->remove)
 			dev->bus->remove(dev);
 		else if (drv->remove)
diff --git a/drivers/base/firmware_class.c b/drivers/base/firmware_class.c
index 1461569..4bad287 100644
--- a/drivers/base/firmware_class.c
+++ b/drivers/base/firmware_class.c
@@ -21,6 +21,8 @@
 #include <linux/firmware.h>
 #include "base.h"
 
+#define to_dev(obj) container_of(obj, struct device, kobj)
+
 MODULE_AUTHOR("Manuel Estrada Sainz <ranty@debian.org>");
 MODULE_DESCRIPTION("Multi purpose firmware loading support");
 MODULE_LICENSE("GPL");
@@ -86,12 +88,12 @@
 
 static CLASS_ATTR(timeout, 0644, firmware_timeout_show, firmware_timeout_store);
 
-static void  fw_class_dev_release(struct class_device *class_dev);
+static void fw_dev_release(struct device *dev);
 
-static int firmware_class_uevent(struct class_device *class_dev, char **envp,
-				 int num_envp, char *buffer, int buffer_size)
+static int firmware_uevent(struct device *dev, char **envp, int num_envp,
+			   char *buffer, int buffer_size)
 {
-	struct firmware_priv *fw_priv = class_get_devdata(class_dev);
+	struct firmware_priv *fw_priv = dev_get_drvdata(dev);
 	int i = 0, len = 0;
 
 	if (!test_bit(FW_STATUS_READY, &fw_priv->status))
@@ -110,21 +112,21 @@
 
 static struct class firmware_class = {
 	.name		= "firmware",
-	.uevent		= firmware_class_uevent,
-	.release	= fw_class_dev_release,
+	.dev_uevent	= firmware_uevent,
+	.dev_release	= fw_dev_release,
 };
 
-static ssize_t
-firmware_loading_show(struct class_device *class_dev, char *buf)
+static ssize_t firmware_loading_show(struct device *dev,
+				     struct device_attribute *attr, char *buf)
 {
-	struct firmware_priv *fw_priv = class_get_devdata(class_dev);
+	struct firmware_priv *fw_priv = dev_get_drvdata(dev);
 	int loading = test_bit(FW_STATUS_LOADING, &fw_priv->status);
 	return sprintf(buf, "%d\n", loading);
 }
 
 /**
  * firmware_loading_store - set value in the 'loading' control file
- * @class_dev: class_device pointer
+ * @dev: device pointer
  * @buf: buffer to scan for loading control value
  * @count: number of bytes in @buf
  *
@@ -134,11 +136,11 @@
  *	 0: Conclude the load and hand the data to the driver code.
  *	-1: Conclude the load with an error and discard any written data.
  **/
-static ssize_t
-firmware_loading_store(struct class_device *class_dev,
-		       const char *buf, size_t count)
+static ssize_t firmware_loading_store(struct device *dev,
+				      struct device_attribute *attr,
+				      const char *buf, size_t count)
 {
-	struct firmware_priv *fw_priv = class_get_devdata(class_dev);
+	struct firmware_priv *fw_priv = dev_get_drvdata(dev);
 	int loading = simple_strtol(buf, NULL, 10);
 
 	switch (loading) {
@@ -174,15 +176,14 @@
 	return count;
 }
 
-static CLASS_DEVICE_ATTR(loading, 0644,
-			firmware_loading_show, firmware_loading_store);
+static DEVICE_ATTR(loading, 0644, firmware_loading_show, firmware_loading_store);
 
 static ssize_t
 firmware_data_read(struct kobject *kobj,
 		   char *buffer, loff_t offset, size_t count)
 {
-	struct class_device *class_dev = to_class_dev(kobj);
-	struct firmware_priv *fw_priv = class_get_devdata(class_dev);
+	struct device *dev = to_dev(kobj);
+	struct firmware_priv *fw_priv = dev_get_drvdata(dev);
 	struct firmware *fw;
 	ssize_t ret_count = count;
 
@@ -234,7 +235,7 @@
 
 /**
  * firmware_data_write - write method for firmware
- * @kobj: kobject for the class_device
+ * @kobj: kobject for the device
  * @buffer: buffer being written
  * @offset: buffer offset for write in total data store area
  * @count: buffer size
@@ -246,8 +247,8 @@
 firmware_data_write(struct kobject *kobj,
 		    char *buffer, loff_t offset, size_t count)
 {
-	struct class_device *class_dev = to_class_dev(kobj);
-	struct firmware_priv *fw_priv = class_get_devdata(class_dev);
+	struct device *dev = to_dev(kobj);
+	struct firmware_priv *fw_priv = dev_get_drvdata(dev);
 	struct firmware *fw;
 	ssize_t retval;
 
@@ -280,13 +281,12 @@
 	.write = firmware_data_write,
 };
 
-static void
-fw_class_dev_release(struct class_device *class_dev)
+static void fw_dev_release(struct device *dev)
 {
-	struct firmware_priv *fw_priv = class_get_devdata(class_dev);
+	struct firmware_priv *fw_priv = dev_get_drvdata(dev);
 
 	kfree(fw_priv);
-	kfree(class_dev);
+	kfree(dev);
 
 	module_put(THIS_MODULE);
 }
@@ -298,26 +298,23 @@
 	fw_load_abort(fw_priv);
 }
 
-static inline void
-fw_setup_class_device_id(struct class_device *class_dev, struct device *dev)
+static inline void fw_setup_device_id(struct device *f_dev, struct device *dev)
 {
 	/* XXX warning we should watch out for name collisions */
-	strlcpy(class_dev->class_id, dev->bus_id, BUS_ID_SIZE);
+	strlcpy(f_dev->bus_id, dev->bus_id, BUS_ID_SIZE);
 }
 
-static int
-fw_register_class_device(struct class_device **class_dev_p,
-			 const char *fw_name, struct device *device)
+static int fw_register_device(struct device **dev_p, const char *fw_name,
+			      struct device *device)
 {
 	int retval;
 	struct firmware_priv *fw_priv = kzalloc(sizeof(*fw_priv),
 						GFP_KERNEL);
-	struct class_device *class_dev = kzalloc(sizeof(*class_dev),
-						 GFP_KERNEL);
+	struct device *f_dev = kzalloc(sizeof(*f_dev), GFP_KERNEL);
 
-	*class_dev_p = NULL;
+	*dev_p = NULL;
 
-	if (!fw_priv || !class_dev) {
+	if (!fw_priv || !f_dev) {
 		printk(KERN_ERR "%s: kmalloc failed\n", __FUNCTION__);
 		retval = -ENOMEM;
 		goto error_kfree;
@@ -331,55 +328,54 @@
 	fw_priv->timeout.data = (u_long) fw_priv;
 	init_timer(&fw_priv->timeout);
 
-	fw_setup_class_device_id(class_dev, device);
-	class_dev->dev = device;
-	class_dev->class = &firmware_class;
-	class_set_devdata(class_dev, fw_priv);
-	retval = class_device_register(class_dev);
+	fw_setup_device_id(f_dev, device);
+	f_dev->parent = device;
+	f_dev->class = &firmware_class;
+	dev_set_drvdata(f_dev, fw_priv);
+	retval = device_register(f_dev);
 	if (retval) {
-		printk(KERN_ERR "%s: class_device_register failed\n",
+		printk(KERN_ERR "%s: device_register failed\n",
 		       __FUNCTION__);
 		goto error_kfree;
 	}
-	*class_dev_p = class_dev;
+	*dev_p = f_dev;
 	return 0;
 
 error_kfree:
 	kfree(fw_priv);
-	kfree(class_dev);
+	kfree(f_dev);
 	return retval;
 }
 
-static int
-fw_setup_class_device(struct firmware *fw, struct class_device **class_dev_p,
-		      const char *fw_name, struct device *device, int uevent)
+static int fw_setup_device(struct firmware *fw, struct device **dev_p,
+			   const char *fw_name, struct device *device,
+			   int uevent)
 {
-	struct class_device *class_dev;
+	struct device *f_dev;
 	struct firmware_priv *fw_priv;
 	int retval;
 
-	*class_dev_p = NULL;
-	retval = fw_register_class_device(&class_dev, fw_name, device);
+	*dev_p = NULL;
+	retval = fw_register_device(&f_dev, fw_name, device);
 	if (retval)
 		goto out;
 
 	/* Need to pin this module until class device is destroyed */
 	__module_get(THIS_MODULE);
 
-	fw_priv = class_get_devdata(class_dev);
+	fw_priv = dev_get_drvdata(f_dev);
 
 	fw_priv->fw = fw;
-	retval = sysfs_create_bin_file(&class_dev->kobj, &fw_priv->attr_data);
+	retval = sysfs_create_bin_file(&f_dev->kobj, &fw_priv->attr_data);
 	if (retval) {
 		printk(KERN_ERR "%s: sysfs_create_bin_file failed\n",
 		       __FUNCTION__);
 		goto error_unreg;
 	}
 
-	retval = class_device_create_file(class_dev,
-					  &class_device_attr_loading);
+	retval = device_create_file(f_dev, &dev_attr_loading);
 	if (retval) {
-		printk(KERN_ERR "%s: class_device_create_file failed\n",
+		printk(KERN_ERR "%s: device_create_file failed\n",
 		       __FUNCTION__);
 		goto error_unreg;
 	}
@@ -388,11 +384,11 @@
                 set_bit(FW_STATUS_READY, &fw_priv->status);
         else
                 set_bit(FW_STATUS_READY_NOHOTPLUG, &fw_priv->status);
-	*class_dev_p = class_dev;
+	*dev_p = f_dev;
 	goto out;
 
 error_unreg:
-	class_device_unregister(class_dev);
+	device_unregister(f_dev);
 out:
 	return retval;
 }
@@ -401,7 +397,7 @@
 _request_firmware(const struct firmware **firmware_p, const char *name,
 		 struct device *device, int uevent)
 {
-	struct class_device *class_dev;
+	struct device *f_dev;
 	struct firmware_priv *fw_priv;
 	struct firmware *firmware;
 	int retval;
@@ -417,12 +413,11 @@
 		goto out;
 	}
 
-	retval = fw_setup_class_device(firmware, &class_dev, name, device,
-				       uevent);
+	retval = fw_setup_device(firmware, &f_dev, name, device, uevent);
 	if (retval)
 		goto error_kfree_fw;
 
-	fw_priv = class_get_devdata(class_dev);
+	fw_priv = dev_get_drvdata(f_dev);
 
 	if (uevent) {
 		if (loading_timeout > 0) {
@@ -430,7 +425,7 @@
 			add_timer(&fw_priv->timeout);
 		}
 
-		kobject_uevent(&class_dev->kobj, KOBJ_ADD);
+		kobject_uevent(&f_dev->kobj, KOBJ_ADD);
 		wait_for_completion(&fw_priv->completion);
 		set_bit(FW_STATUS_DONE, &fw_priv->status);
 		del_timer_sync(&fw_priv->timeout);
@@ -445,7 +440,7 @@
 	}
 	fw_priv->fw = NULL;
 	mutex_unlock(&fw_lock);
-	class_device_unregister(class_dev);
+	device_unregister(f_dev);
 	goto out;
 
 error_kfree_fw:
diff --git a/drivers/base/platform.c b/drivers/base/platform.c
index 940ce41..d1df4a0 100644
--- a/drivers/base/platform.c
+++ b/drivers/base/platform.c
@@ -388,6 +388,11 @@
 	return drv->probe(dev);
 }
 
+static int platform_drv_probe_fail(struct device *_dev)
+{
+	return -ENXIO;
+}
+
 static int platform_drv_remove(struct device *_dev)
 {
 	struct platform_driver *drv = to_platform_driver(_dev->driver);
@@ -451,6 +456,49 @@
 }
 EXPORT_SYMBOL_GPL(platform_driver_unregister);
 
+/**
+ * platform_driver_probe - register driver for non-hotpluggable device
+ * @drv: platform driver structure
+ * @probe: the driver probe routine, probably from an __init section
+ *
+ * Use this instead of platform_driver_register() when you know the device
+ * is not hotpluggable and has already been registered, and you want to
+ * remove its run-once probe() infrastructure from memory after the driver
+ * has bound to the device.
+ *
+ * One typical use for this would be with drivers for controllers integrated
+ * into system-on-chip processors, where the controller devices have been
+ * configured as part of board setup.
+ *
+ * Returns zero if the driver registered and bound to a device, else returns
+ * a negative error code and with the driver not registered.
+ */
+int platform_driver_probe(struct platform_driver *drv,
+		int (*probe)(struct platform_device *))
+{
+	int retval, code;
+
+	/* temporary section violation during probe() */
+	drv->probe = probe;
+	retval = code = platform_driver_register(drv);
+
+	/* Fixup that section violation, being paranoid about code scanning
+	 * the list of drivers in order to probe new devices.  Check to see
+	 * if the probe was successful, and make sure any forced probes of
+	 * new devices fail.
+	 */
+	spin_lock(&platform_bus_type.klist_drivers.k_lock);
+	drv->probe = NULL;
+	if (code == 0 && list_empty(&drv->driver.klist_devices.k_list))
+		retval = -ENODEV;
+	drv->driver.probe = platform_drv_probe_fail;
+	spin_unlock(&platform_bus_type.klist_drivers.k_lock);
+
+	if (code != retval)
+		platform_driver_unregister(drv);
+	return retval;
+}
+EXPORT_SYMBOL_GPL(platform_driver_probe);
 
 /* modalias support enables more hands-off userspace setup:
  * (a) environment variable lets new-style hotplug events work once system is
diff --git a/drivers/base/topology.c b/drivers/base/topology.c
index 28dccb7..3d12b85 100644
--- a/drivers/base/topology.c
+++ b/drivers/base/topology.c
@@ -94,54 +94,63 @@
 	.name = "topology"
 };
 
+static cpumask_t topology_dev_map = CPU_MASK_NONE;
+
 /* Add/Remove cpu_topology interface for CPU device */
-static int __cpuinit topology_add_dev(struct sys_device * sys_dev)
+static int __cpuinit topology_add_dev(unsigned int cpu)
 {
-	return sysfs_create_group(&sys_dev->kobj, &topology_attr_group);
+	int rc;
+	struct sys_device *sys_dev = get_cpu_sysdev(cpu);
+
+	rc = sysfs_create_group(&sys_dev->kobj, &topology_attr_group);
+	if (!rc)
+		cpu_set(cpu, topology_dev_map);
+	return rc;
 }
 
-static int __cpuinit topology_remove_dev(struct sys_device * sys_dev)
+#ifdef CONFIG_HOTPLUG_CPU
+static void __cpuinit topology_remove_dev(unsigned int cpu)
 {
+	struct sys_device *sys_dev = get_cpu_sysdev(cpu);
+
+	if (!cpu_isset(cpu, topology_dev_map))
+		return;
+	cpu_clear(cpu, topology_dev_map);
 	sysfs_remove_group(&sys_dev->kobj, &topology_attr_group);
-	return 0;
 }
 
 static int __cpuinit topology_cpu_callback(struct notifier_block *nfb,
-		unsigned long action, void *hcpu)
+					   unsigned long action, void *hcpu)
 {
 	unsigned int cpu = (unsigned long)hcpu;
-	struct sys_device *sys_dev;
+	int rc = 0;
 
-	sys_dev = get_cpu_sysdev(cpu);
 	switch (action) {
-	case CPU_ONLINE:
-		topology_add_dev(sys_dev);
+	case CPU_UP_PREPARE:
+		rc = topology_add_dev(cpu);
 		break;
+	case CPU_UP_CANCELED:
 	case CPU_DEAD:
-		topology_remove_dev(sys_dev);
+		topology_remove_dev(cpu);
 		break;
 	}
-	return NOTIFY_OK;
+	return rc ? NOTIFY_BAD : NOTIFY_OK;
 }
-
-static struct notifier_block __cpuinitdata topology_cpu_notifier =
-{
-	.notifier_call = topology_cpu_callback,
-};
+#endif
 
 static int __cpuinit topology_sysfs_init(void)
 {
-	int i;
+	int cpu;
+	int rc;
 
-	for_each_online_cpu(i) {
-		topology_cpu_callback(&topology_cpu_notifier, CPU_ONLINE,
-				(void *)(long)i);
+	for_each_online_cpu(cpu) {
+		rc = topology_add_dev(cpu);
+		if (rc)
+			return rc;
 	}
-
-	register_hotcpu_notifier(&topology_cpu_notifier);
+	hotcpu_notifier(topology_cpu_callback, 0);
 
 	return 0;
 }
 
 device_initcall(topology_sysfs_init);
-
diff --git a/drivers/cdrom/cdrom.c b/drivers/cdrom/cdrom.c
index 7ea0f48..2df5cf4 100644
--- a/drivers/cdrom/cdrom.c
+++ b/drivers/cdrom/cdrom.c
@@ -2133,16 +2133,14 @@
 		rq->timeout = 60 * HZ;
 		bio = rq->bio;
 
-		if (rq->bio)
-			blk_queue_bounce(q, &rq->bio);
-
 		if (blk_execute_rq(q, cdi->disk, rq, 0)) {
 			struct request_sense *s = rq->sense;
 			ret = -EIO;
 			cdi->last_sense = s->sense_key;
 		}
 
-		if (blk_rq_unmap_user(bio, len))
+		rq->bio = bio;
+		if (blk_rq_unmap_user(rq))
 			ret = -EFAULT;
 
 		if (ret)
diff --git a/drivers/char/Kconfig b/drivers/char/Kconfig
index 2af12fc..ad8b537 100644
--- a/drivers/char/Kconfig
+++ b/drivers/char/Kconfig
@@ -994,7 +994,7 @@
 	help
 	  If you say Y here, you will have a miscdevice named "/dev/hpet/".  Each
 	  open selects one of the timers supported by the HPET.  The timers are
-	  non-periodioc and/or periodic.
+	  non-periodic and/or periodic.
 
 config HPET_RTC_IRQ
 	bool "HPET Control RTC IRQ" if !HPET_EMULATE_RTC
diff --git a/drivers/char/hw_random/core.c b/drivers/char/hw_random/core.c
index 154a81d..ebace20 100644
--- a/drivers/char/hw_random/core.c
+++ b/drivers/char/hw_random/core.c
@@ -162,7 +162,8 @@
 };
 
 
-static ssize_t hwrng_attr_current_store(struct class_device *class,
+static ssize_t hwrng_attr_current_store(struct device *dev,
+					struct device_attribute *attr,
 					const char *buf, size_t len)
 {
 	int err;
@@ -192,7 +193,8 @@
 	return err ? : len;
 }
 
-static ssize_t hwrng_attr_current_show(struct class_device *class,
+static ssize_t hwrng_attr_current_show(struct device *dev,
+				       struct device_attribute *attr,
 				       char *buf)
 {
 	int err;
@@ -210,7 +212,8 @@
 	return ret;
 }
 
-static ssize_t hwrng_attr_available_show(struct class_device *class,
+static ssize_t hwrng_attr_available_show(struct device *dev,
+					 struct device_attribute *attr,
 					 char *buf)
 {
 	int err;
@@ -234,20 +237,18 @@
 	return ret;
 }
 
-static CLASS_DEVICE_ATTR(rng_current, S_IRUGO | S_IWUSR,
-			 hwrng_attr_current_show,
-			 hwrng_attr_current_store);
-static CLASS_DEVICE_ATTR(rng_available, S_IRUGO,
-			 hwrng_attr_available_show,
-			 NULL);
+static DEVICE_ATTR(rng_current, S_IRUGO | S_IWUSR,
+		   hwrng_attr_current_show,
+		   hwrng_attr_current_store);
+static DEVICE_ATTR(rng_available, S_IRUGO,
+		   hwrng_attr_available_show,
+		   NULL);
 
 
 static void unregister_miscdev(void)
 {
-	class_device_remove_file(rng_miscdev.class,
-				 &class_device_attr_rng_available);
-	class_device_remove_file(rng_miscdev.class,
-				 &class_device_attr_rng_current);
+	device_remove_file(rng_miscdev.this_device, &dev_attr_rng_available);
+	device_remove_file(rng_miscdev.this_device, &dev_attr_rng_current);
 	misc_deregister(&rng_miscdev);
 }
 
@@ -258,20 +259,19 @@
 	err = misc_register(&rng_miscdev);
 	if (err)
 		goto out;
-	err = class_device_create_file(rng_miscdev.class,
-				       &class_device_attr_rng_current);
+	err = device_create_file(rng_miscdev.this_device,
+				 &dev_attr_rng_current);
 	if (err)
 		goto err_misc_dereg;
-	err = class_device_create_file(rng_miscdev.class,
-				       &class_device_attr_rng_available);
+	err = device_create_file(rng_miscdev.this_device,
+				 &dev_attr_rng_available);
 	if (err)
 		goto err_remove_current;
 out:
 	return err;
 
 err_remove_current:
-	class_device_remove_file(rng_miscdev.class,
-				 &class_device_attr_rng_current);
+	device_remove_file(rng_miscdev.this_device, &dev_attr_rng_current);
 err_misc_dereg:
 	misc_deregister(&rng_miscdev);
 	goto out;
diff --git a/drivers/char/mem.c b/drivers/char/mem.c
index 5547337..e67eef4 100644
--- a/drivers/char/mem.c
+++ b/drivers/char/mem.c
@@ -980,10 +980,10 @@
 
 	mem_class = class_create(THIS_MODULE, "mem");
 	for (i = 0; i < ARRAY_SIZE(devlist); i++)
-		class_device_create(mem_class, NULL,
-					MKDEV(MEM_MAJOR, devlist[i].minor),
-					NULL, devlist[i].name);
-	
+		device_create(mem_class, NULL,
+			      MKDEV(MEM_MAJOR, devlist[i].minor),
+			      devlist[i].name);
+
 	return 0;
 }
 
diff --git a/drivers/char/misc.c b/drivers/char/misc.c
index 62ebe09..7a484fc 100644
--- a/drivers/char/misc.c
+++ b/drivers/char/misc.c
@@ -169,11 +169,6 @@
 	return err;
 }
 
-/* 
- * TODO for 2.7:
- *  - add a struct kref to struct miscdevice and make all usages of
- *    them dynamic.
- */
 static struct class *misc_class;
 
 static const struct file_operations misc_fops = {
@@ -228,10 +223,10 @@
 		misc_minors[misc->minor >> 3] |= 1 << (misc->minor & 7);
 	dev = MKDEV(MISC_MAJOR, misc->minor);
 
-	misc->class = class_device_create(misc_class, NULL, dev, misc->dev,
+	misc->this_device = device_create(misc_class, misc->parent, dev,
 					  "%s", misc->name);
-	if (IS_ERR(misc->class)) {
-		err = PTR_ERR(misc->class);
+	if (IS_ERR(misc->this_device)) {
+		err = PTR_ERR(misc->this_device);
 		goto out;
 	}
 
@@ -264,7 +259,7 @@
 
 	down(&misc_sem);
 	list_del(&misc->list);
-	class_device_destroy(misc_class, MKDEV(MISC_MAJOR, misc->minor));
+	device_destroy(misc_class, MKDEV(MISC_MAJOR, misc->minor));
 	if (i < DYNAMIC_MINORS && i>0) {
 		misc_minors[i>>3] &= ~(1 << (misc->minor & 7));
 	}
diff --git a/drivers/char/ppdev.c b/drivers/char/ppdev.c
index efc485e..c1e3dd8 100644
--- a/drivers/char/ppdev.c
+++ b/drivers/char/ppdev.c
@@ -752,13 +752,13 @@
 
 static void pp_attach(struct parport *port)
 {
-	class_device_create(ppdev_class, NULL, MKDEV(PP_MAJOR, port->number),
-			NULL, "parport%d", port->number);
+	device_create(ppdev_class, NULL, MKDEV(PP_MAJOR, port->number),
+			"parport%d", port->number);
 }
 
 static void pp_detach(struct parport *port)
 {
-	class_device_destroy(ppdev_class, MKDEV(PP_MAJOR, port->number));
+	device_destroy(ppdev_class, MKDEV(PP_MAJOR, port->number));
 }
 
 static struct parport_driver pp_driver = {
diff --git a/drivers/char/raw.c b/drivers/char/raw.c
index 89b718e..3b32313 100644
--- a/drivers/char/raw.c
+++ b/drivers/char/raw.c
@@ -127,9 +127,9 @@
 
 static void bind_device(struct raw_config_request *rq)
 {
-	class_device_destroy(raw_class, MKDEV(RAW_MAJOR, rq->raw_minor));
-	class_device_create(raw_class, NULL, MKDEV(RAW_MAJOR, rq->raw_minor),
-				      NULL, "raw%d", rq->raw_minor);
+	device_destroy(raw_class, MKDEV(RAW_MAJOR, rq->raw_minor));
+	device_create(raw_class, NULL, MKDEV(RAW_MAJOR, rq->raw_minor),
+		      "raw%d", rq->raw_minor);
 }
 
 /*
@@ -200,7 +200,7 @@
 			if (rq.block_major == 0 && rq.block_minor == 0) {
 				/* unbind */
 				rawdev->binding = NULL;
-				class_device_destroy(raw_class,
+				device_destroy(raw_class,
 						MKDEV(RAW_MAJOR, rq.raw_minor));
 			} else {
 				rawdev->binding = bdget(dev);
@@ -283,7 +283,7 @@
 		ret = PTR_ERR(raw_class);
 		goto error_region;
 	}
-	class_device_create(raw_class, NULL, MKDEV(RAW_MAJOR, 0), NULL, "rawctl");
+	device_create(raw_class, NULL, MKDEV(RAW_MAJOR, 0), "rawctl");
 
 	return 0;
 
@@ -295,7 +295,7 @@
 
 static void __exit raw_exit(void)
 {
-	class_device_destroy(raw_class, MKDEV(RAW_MAJOR, 0));
+	device_destroy(raw_class, MKDEV(RAW_MAJOR, 0));
 	class_destroy(raw_class);
 	cdev_del(&raw_cdev);
 	unregister_chrdev_region(MKDEV(RAW_MAJOR, 0), MAX_RAW_MINORS);
diff --git a/drivers/char/rio/riocmd.c b/drivers/char/rio/riocmd.c
index 4df6ab2..167ebc8 100644
--- a/drivers/char/rio/riocmd.c
+++ b/drivers/char/rio/riocmd.c
@@ -922,7 +922,7 @@
 ** 
 ** Packet is an actual packet structure to be filled in with the packet
 ** information associated with the command. You need to fill in everything,
-** as the command processore doesn't process the command packet in any way.
+** as the command processor doesn't process the command packet in any way.
 ** 
 ** The PreFuncP is called before the packet is enqueued on the host rup.
 ** PreFuncP is called as (*PreFuncP)(PreArg, CmdBlkP);. PreFuncP must
diff --git a/drivers/char/rio/rioinit.c b/drivers/char/rio/rioinit.c
index 99f3df0..0794844 100644
--- a/drivers/char/rio/rioinit.c
+++ b/drivers/char/rio/rioinit.c
@@ -222,7 +222,7 @@
 ** which value will be written into memory.
 ** Call with op set to zero means that the RAM will not be read and checked
 ** before it is written.
-** Call with op not zero, and the RAM will be read and compated with val[op-1]
+** Call with op not zero and the RAM will be read and compared with val[op-1]
 ** to check that the data from the previous phase was retained.
 */
 
diff --git a/drivers/char/rio/rioparam.c b/drivers/char/rio/rioparam.c
index 1066d97..bb498d2 100644
--- a/drivers/char/rio/rioparam.c
+++ b/drivers/char/rio/rioparam.c
@@ -87,8 +87,8 @@
 ** command bit set onto the port. The command bit is in the len field,
 ** and gets ORed in with the actual byte count.
 **
-** When you send a packet with the command bit set, then the first
-** data byte ( data[0] ) is interpretted as the command to execute.
+** When you send a packet with the command bit set the first
+** data byte (data[0]) is interpreted as the command to execute.
 ** It also governs what data structure overlay should accompany the packet.
 ** Commands are defined in cirrus/cirrus.h
 **
@@ -103,7 +103,7 @@
 **
 ** Most commands do not use the remaining bytes in the data array. The
 ** exceptions are OPEN MOPEN and CONFIG. (NB. As with the SI CONFIG and
-** OPEN are currently analagous). With these three commands the following
+** OPEN are currently analogous). With these three commands the following
 ** 11 data bytes are all used to pass config information such as baud rate etc.
 ** The fields are also defined in cirrus.h. Some contain straightforward
 ** information such as the transmit XON character. Two contain the transmit and
diff --git a/drivers/char/tpm/tpm.c b/drivers/char/tpm/tpm.c
index 6ad2d3b..6e1329d 100644
--- a/drivers/char/tpm/tpm.c
+++ b/drivers/char/tpm/tpm.c
@@ -1130,7 +1130,7 @@
 	scnprintf(devname, DEVNAME_SIZE, "%s%d", "tpm", chip->dev_num);
 	chip->vendor.miscdev.name = devname;
 
-	chip->vendor.miscdev.dev = dev;
+	chip->vendor.miscdev.parent = dev;
 	chip->dev = get_device(dev);
 
 	if (misc_register(&chip->vendor.miscdev)) {
diff --git a/drivers/char/tty_io.c b/drivers/char/tty_io.c
index e90ea39..50dc492 100644
--- a/drivers/char/tty_io.c
+++ b/drivers/char/tty_io.c
@@ -3612,7 +3612,8 @@
  *		This field is optional, if there is no known struct device
  *		for this tty device it can be set to NULL safely.
  *
- *	Returns a pointer to the class device (or ERR_PTR(-EFOO) on error).
+ *	Returns a pointer to the struct device for this tty device
+ *	(or ERR_PTR(-EFOO) on error).
  *
  *	This call is required to be made to register an individual tty device
  *	if the tty driver's flags have the TTY_DRIVER_DYNAMIC_DEV bit set.  If
@@ -3622,8 +3623,8 @@
  *	Locking: ??
  */
 
-struct class_device *tty_register_device(struct tty_driver *driver,
-					 unsigned index, struct device *device)
+struct device *tty_register_device(struct tty_driver *driver, unsigned index,
+				   struct device *device)
 {
 	char name[64];
 	dev_t dev = MKDEV(driver->major, driver->minor_start) + index;
@@ -3639,7 +3640,7 @@
 	else
 		tty_line_name(driver, index, name);
 
-	return class_device_create(tty_class, NULL, dev, device, "%s", name);
+	return device_create(tty_class, device, dev, name);
 }
 
 /**
@@ -3655,7 +3656,7 @@
 
 void tty_unregister_device(struct tty_driver *driver, unsigned index)
 {
-	class_device_destroy(tty_class, MKDEV(driver->major, driver->minor_start) + index);
+	device_destroy(tty_class, MKDEV(driver->major, driver->minor_start) + index);
 }
 
 EXPORT_SYMBOL(tty_register_device);
@@ -3895,20 +3896,20 @@
 	if (cdev_add(&tty_cdev, MKDEV(TTYAUX_MAJOR, 0), 1) ||
 	    register_chrdev_region(MKDEV(TTYAUX_MAJOR, 0), 1, "/dev/tty") < 0)
 		panic("Couldn't register /dev/tty driver\n");
-	class_device_create(tty_class, NULL, MKDEV(TTYAUX_MAJOR, 0), NULL, "tty");
+	device_create(tty_class, NULL, MKDEV(TTYAUX_MAJOR, 0), "tty");
 
 	cdev_init(&console_cdev, &console_fops);
 	if (cdev_add(&console_cdev, MKDEV(TTYAUX_MAJOR, 1), 1) ||
 	    register_chrdev_region(MKDEV(TTYAUX_MAJOR, 1), 1, "/dev/console") < 0)
 		panic("Couldn't register /dev/console driver\n");
-	class_device_create(tty_class, NULL, MKDEV(TTYAUX_MAJOR, 1), NULL, "console");
+	device_create(tty_class, NULL, MKDEV(TTYAUX_MAJOR, 1), "console");
 
 #ifdef CONFIG_UNIX98_PTYS
 	cdev_init(&ptmx_cdev, &ptmx_fops);
 	if (cdev_add(&ptmx_cdev, MKDEV(TTYAUX_MAJOR, 2), 1) ||
 	    register_chrdev_region(MKDEV(TTYAUX_MAJOR, 2), 1, "/dev/ptmx") < 0)
 		panic("Couldn't register /dev/ptmx driver\n");
-	class_device_create(tty_class, NULL, MKDEV(TTYAUX_MAJOR, 2), NULL, "ptmx");
+	device_create(tty_class, NULL, MKDEV(TTYAUX_MAJOR, 2), "ptmx");
 #endif
 
 #ifdef CONFIG_VT
@@ -3916,7 +3917,7 @@
 	if (cdev_add(&vc0_cdev, MKDEV(TTY_MAJOR, 0), 1) ||
 	    register_chrdev_region(MKDEV(TTY_MAJOR, 0), 1, "/dev/vc/0") < 0)
 		panic("Couldn't register /dev/tty0 driver\n");
-	class_device_create(tty_class, NULL, MKDEV(TTY_MAJOR, 0), NULL, "tty0");
+	device_create(tty_class, NULL, MKDEV(TTY_MAJOR, 0), "tty0");
 
 	vty_init();
 #endif
diff --git a/drivers/char/vc_screen.c b/drivers/char/vc_screen.c
index bd7a98c..f442b57 100644
--- a/drivers/char/vc_screen.c
+++ b/drivers/char/vc_screen.c
@@ -476,16 +476,16 @@
 
 void vcs_make_sysfs(struct tty_struct *tty)
 {
-	class_device_create(vc_class, NULL, MKDEV(VCS_MAJOR, tty->index + 1),
-			NULL, "vcs%u", tty->index + 1);
-	class_device_create(vc_class, NULL, MKDEV(VCS_MAJOR, tty->index + 129),
-			NULL, "vcsa%u", tty->index + 1);
+	device_create(vc_class, NULL, MKDEV(VCS_MAJOR, tty->index + 1),
+			"vcs%u", tty->index + 1);
+	device_create(vc_class, NULL, MKDEV(VCS_MAJOR, tty->index + 129),
+			"vcsa%u", tty->index + 1);
 }
 
 void vcs_remove_sysfs(struct tty_struct *tty)
 {
-	class_device_destroy(vc_class, MKDEV(VCS_MAJOR, tty->index + 1));
-	class_device_destroy(vc_class, MKDEV(VCS_MAJOR, tty->index + 129));
+	device_destroy(vc_class, MKDEV(VCS_MAJOR, tty->index + 1));
+	device_destroy(vc_class, MKDEV(VCS_MAJOR, tty->index + 129));
 }
 
 int __init vcs_init(void)
@@ -494,7 +494,7 @@
 		panic("unable to get major %d for vcs device", VCS_MAJOR);
 	vc_class = class_create(THIS_MODULE, "vc");
 
-	class_device_create(vc_class, NULL, MKDEV(VCS_MAJOR, 0), NULL, "vcs");
-	class_device_create(vc_class, NULL, MKDEV(VCS_MAJOR, 128), NULL, "vcsa");
+	device_create(vc_class, NULL, MKDEV(VCS_MAJOR, 0), "vcs");
+	device_create(vc_class, NULL, MKDEV(VCS_MAJOR, 128), "vcsa");
 	return 0;
 }
diff --git a/drivers/char/vt.c b/drivers/char/vt.c
index 8e4413f..87587b4 100644
--- a/drivers/char/vt.c
+++ b/drivers/char/vt.c
@@ -112,7 +112,7 @@
 struct con_driver {
 	const struct consw *con;
 	const char *desc;
-	struct class_device *class_dev;
+	struct device *dev;
 	int node;
 	int first;
 	int last;
@@ -3023,10 +3023,10 @@
 }
 #endif /* CONFIG_VT_HW_CONSOLE_BINDING */
 
-static ssize_t store_bind(struct class_device *class_device,
+static ssize_t store_bind(struct device *dev, struct device_attribute *attr,
 			  const char *buf, size_t count)
 {
-	struct con_driver *con = class_get_devdata(class_device);
+	struct con_driver *con = dev_get_drvdata(dev);
 	int bind = simple_strtoul(buf, NULL, 0);
 
 	if (bind)
@@ -3037,17 +3037,19 @@
 	return count;
 }
 
-static ssize_t show_bind(struct class_device *class_device, char *buf)
+static ssize_t show_bind(struct device *dev, struct device_attribute *attr,
+			 char *buf)
 {
-	struct con_driver *con = class_get_devdata(class_device);
+	struct con_driver *con = dev_get_drvdata(dev);
 	int bind = con_is_bound(con->con);
 
 	return snprintf(buf, PAGE_SIZE, "%i\n", bind);
 }
 
-static ssize_t show_name(struct class_device *class_device, char *buf)
+static ssize_t show_name(struct device *dev, struct device_attribute *attr,
+			 char *buf)
 {
-	struct con_driver *con = class_get_devdata(class_device);
+	struct con_driver *con = dev_get_drvdata(dev);
 
 	return snprintf(buf, PAGE_SIZE, "%s %s\n",
 			(con->flag & CON_DRIVER_FLAG_MODULE) ? "(M)" : "(S)",
@@ -3055,43 +3057,40 @@
 
 }
 
-static struct class_device_attribute class_device_attrs[] = {
+static struct device_attribute device_attrs[] = {
 	__ATTR(bind, S_IRUGO|S_IWUSR, show_bind, store_bind),
 	__ATTR(name, S_IRUGO, show_name, NULL),
 };
 
-static int vtconsole_init_class_device(struct con_driver *con)
+static int vtconsole_init_device(struct con_driver *con)
 {
 	int i;
 	int error = 0;
 
 	con->flag |= CON_DRIVER_FLAG_ATTR;
-	class_set_devdata(con->class_dev, con);
-	for (i = 0; i < ARRAY_SIZE(class_device_attrs); i++) {
-		error = class_device_create_file(con->class_dev,
-					 &class_device_attrs[i]);
+	dev_set_drvdata(con->dev, con);
+	for (i = 0; i < ARRAY_SIZE(device_attrs); i++) {
+		error = device_create_file(con->dev, &device_attrs[i]);
 		if (error)
 			break;
 	}
 
 	if (error) {
 		while (--i >= 0)
-			class_device_remove_file(con->class_dev,
-					 &class_device_attrs[i]);
+			device_remove_file(con->dev, &device_attrs[i]);
 		con->flag &= ~CON_DRIVER_FLAG_ATTR;
 	}
 
 	return error;
 }
 
-static void vtconsole_deinit_class_device(struct con_driver *con)
+static void vtconsole_deinit_device(struct con_driver *con)
 {
 	int i;
 
 	if (con->flag & CON_DRIVER_FLAG_ATTR) {
-		for (i = 0; i < ARRAY_SIZE(class_device_attrs); i++)
-			class_device_remove_file(con->class_dev,
-						 &class_device_attrs[i]);
+		for (i = 0; i < ARRAY_SIZE(device_attrs); i++)
+			device_remove_file(con->dev, &device_attrs[i]);
 		con->flag &= ~CON_DRIVER_FLAG_ATTR;
 	}
 }
@@ -3179,18 +3178,17 @@
 	if (retval)
 		goto err;
 
-	con_driver->class_dev = class_device_create(vtconsole_class, NULL,
-						    MKDEV(0, con_driver->node),
-						    NULL, "vtcon%i",
-						    con_driver->node);
+	con_driver->dev = device_create(vtconsole_class, NULL,
+					MKDEV(0, con_driver->node),
+					"vtcon%i", con_driver->node);
 
-	if (IS_ERR(con_driver->class_dev)) {
-		printk(KERN_WARNING "Unable to create class_device for %s; "
+	if (IS_ERR(con_driver->dev)) {
+		printk(KERN_WARNING "Unable to create device for %s; "
 		       "errno = %ld\n", con_driver->desc,
-		       PTR_ERR(con_driver->class_dev));
-		con_driver->class_dev = NULL;
+		       PTR_ERR(con_driver->dev));
+		con_driver->dev = NULL;
 	} else {
-		vtconsole_init_class_device(con_driver);
+		vtconsole_init_device(con_driver);
 	}
 
 err:
@@ -3226,12 +3224,12 @@
 
 		if (con_driver->con == csw &&
 		    con_driver->flag & CON_DRIVER_FLAG_MODULE) {
-			vtconsole_deinit_class_device(con_driver);
-			class_device_destroy(vtconsole_class,
-					     MKDEV(0, con_driver->node));
+			vtconsole_deinit_device(con_driver);
+			device_destroy(vtconsole_class,
+				       MKDEV(0, con_driver->node));
 			con_driver->con = NULL;
 			con_driver->desc = NULL;
-			con_driver->class_dev = NULL;
+			con_driver->dev = NULL;
 			con_driver->node = 0;
 			con_driver->flag = 0;
 			con_driver->first = 0;
@@ -3289,19 +3287,18 @@
 	for (i = 0; i < MAX_NR_CON_DRIVER; i++) {
 		struct con_driver *con = &registered_con_driver[i];
 
-		if (con->con && !con->class_dev) {
-			con->class_dev =
-				class_device_create(vtconsole_class, NULL,
-						    MKDEV(0, con->node), NULL,
-						    "vtcon%i", con->node);
+		if (con->con && !con->dev) {
+			con->dev = device_create(vtconsole_class, NULL,
+						 MKDEV(0, con->node),
+						 "vtcon%i", con->node);
 
-			if (IS_ERR(con->class_dev)) {
+			if (IS_ERR(con->dev)) {
 				printk(KERN_WARNING "Unable to create "
-				       "class_device for %s; errno = %ld\n",
-				       con->desc, PTR_ERR(con->class_dev));
-				con->class_dev = NULL;
+				       "device for %s; errno = %ld\n",
+				       con->desc, PTR_ERR(con->dev));
+				con->dev = NULL;
 			} else {
-				vtconsole_init_class_device(con);
+				vtconsole_init_device(con);
 			}
 		}
 	}
diff --git a/drivers/char/watchdog/pcwd_usb.c b/drivers/char/watchdog/pcwd_usb.c
index bda4533..e275dd4 100644
--- a/drivers/char/watchdog/pcwd_usb.c
+++ b/drivers/char/watchdog/pcwd_usb.c
@@ -561,8 +561,7 @@
  */
 static inline void usb_pcwd_delete (struct usb_pcwd_private *usb_pcwd)
 {
-	if (usb_pcwd->intr_urb != NULL)
-		usb_free_urb (usb_pcwd->intr_urb);
+	usb_free_urb(usb_pcwd->intr_urb);
 	if (usb_pcwd->intr_buffer != NULL)
 		usb_buffer_free(usb_pcwd->udev, usb_pcwd->intr_size,
 				usb_pcwd->intr_buffer, usb_pcwd->intr_dma);
diff --git a/drivers/i2c/busses/Kconfig b/drivers/i2c/busses/Kconfig
index 510816c..04bee52 100644
--- a/drivers/i2c/busses/Kconfig
+++ b/drivers/i2c/busses/Kconfig
@@ -125,6 +125,7 @@
 	    ICH7
 	    ESB2
 	    ICH8
+	    ICH9
 
 	  This driver can also be built as a module.  If so, the module
 	  will be called i2c-i801.
diff --git a/drivers/i2c/busses/i2c-i801.c b/drivers/i2c/busses/i2c-i801.c
index bbb2fbe..c7be2fd 100644
--- a/drivers/i2c/busses/i2c-i801.c
+++ b/drivers/i2c/busses/i2c-i801.c
@@ -33,6 +33,7 @@
     ICH7		27DA
     ESB2		269B
     ICH8		283E
+    ICH9		2930
     This driver supports several versions of Intel's I/O Controller Hubs (ICH).
     For SMBus support, they are similar to the PIIX4 and are part
     of Intel's '810' and other chipsets.
@@ -457,6 +458,7 @@
 	{ PCI_DEVICE(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_ICH7_17) },
 	{ PCI_DEVICE(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_ESB2_17) },
 	{ PCI_DEVICE(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_ICH8_5) },
+	{ PCI_DEVICE(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_ICH9_6) },
 	{ 0, }
 };
 
diff --git a/drivers/i2c/i2c-dev.c b/drivers/i2c/i2c-dev.c
index 3f86903..94a4e9a 100644
--- a/drivers/i2c/i2c-dev.c
+++ b/drivers/i2c/i2c-dev.c
@@ -42,7 +42,7 @@
 struct i2c_dev {
 	struct list_head list;
 	struct i2c_adapter *adap;
-	struct class_device *class_dev;
+	struct device *dev;
 };
 
 #define I2C_MINORS	256
@@ -92,15 +92,16 @@
 	spin_unlock(&i2c_dev_list_lock);
 }
 
-static ssize_t show_adapter_name(struct class_device *class_dev, char *buf)
+static ssize_t show_adapter_name(struct device *dev,
+				 struct device_attribute *attr, char *buf)
 {
-	struct i2c_dev *i2c_dev = i2c_dev_get_by_minor(MINOR(class_dev->devt));
+	struct i2c_dev *i2c_dev = i2c_dev_get_by_minor(MINOR(dev->devt));
 
 	if (!i2c_dev)
 		return -ENODEV;
 	return sprintf(buf, "%s\n", i2c_dev->adap->name);
 }
-static CLASS_DEVICE_ATTR(name, S_IRUGO, show_adapter_name, NULL);
+static DEVICE_ATTR(name, S_IRUGO, show_adapter_name, NULL);
 
 static ssize_t i2cdev_read (struct file *file, char __user *buf, size_t count,
                             loff_t *offset)
@@ -413,15 +414,14 @@
 		return PTR_ERR(i2c_dev);
 
 	/* register this i2c device with the driver core */
-	i2c_dev->class_dev = class_device_create(i2c_dev_class, NULL,
-						 MKDEV(I2C_MAJOR, adap->nr),
-						 &adap->dev, "i2c-%d",
-						 adap->nr);
-	if (!i2c_dev->class_dev) {
+	i2c_dev->dev = device_create(i2c_dev_class, &adap->dev,
+				     MKDEV(I2C_MAJOR, adap->nr),
+				     "i2c-%d", adap->nr);
+	if (!i2c_dev->dev) {
 		res = -ENODEV;
 		goto error;
 	}
-	res = class_device_create_file(i2c_dev->class_dev, &class_device_attr_name);
+	res = device_create_file(i2c_dev->dev, &dev_attr_name);
 	if (res)
 		goto error_destroy;
 
@@ -429,7 +429,7 @@
 		 adap->name, adap->nr);
 	return 0;
 error_destroy:
-	class_device_destroy(i2c_dev_class, MKDEV(I2C_MAJOR, adap->nr));
+	device_destroy(i2c_dev_class, MKDEV(I2C_MAJOR, adap->nr));
 error:
 	return_i2c_dev(i2c_dev);
 	kfree(i2c_dev);
@@ -444,9 +444,9 @@
 	if (!i2c_dev) /* attach_adapter must have failed */
 		return 0;
 
-	class_device_remove_file(i2c_dev->class_dev, &class_device_attr_name);
+	device_remove_file(i2c_dev->dev, &dev_attr_name);
 	return_i2c_dev(i2c_dev);
-	class_device_destroy(i2c_dev_class, MKDEV(I2C_MAJOR, adap->nr));
+	device_destroy(i2c_dev_class, MKDEV(I2C_MAJOR, adap->nr));
 	kfree(i2c_dev);
 
 	pr_debug("i2c-dev: adapter [%s] unregistered\n", adap->name);
diff --git a/drivers/ide/ide-floppy.c b/drivers/ide/ide-floppy.c
index 8ccee9c..e3a2676 100644
--- a/drivers/ide/ide-floppy.c
+++ b/drivers/ide/ide-floppy.c
@@ -1635,7 +1635,7 @@
 /*
 ** Get ATAPI_FORMAT_UNIT progress indication.
 **
-** Userland gives a pointer to an int.  The int is set to a progresss
+** Userland gives a pointer to an int.  The int is set to a progress
 ** indicator 0-65536, with 65536=100%.
 **
 ** If the drive does not support format progress indication, we just check
diff --git a/drivers/infiniband/core/addr.c b/drivers/infiniband/core/addr.c
index e11187e..7767a11 100644
--- a/drivers/infiniband/core/addr.c
+++ b/drivers/infiniband/core/addr.c
@@ -139,7 +139,7 @@
 
 	mutex_lock(&lock);
 	list_for_each_entry_reverse(temp_req, &req_list, list) {
-		if (time_after(req->timeout, temp_req->timeout))
+		if (time_after_eq(req->timeout, temp_req->timeout))
 			break;
 	}
 
@@ -225,19 +225,17 @@
 
 	mutex_lock(&lock);
 	list_for_each_entry_safe(req, temp_req, &req_list, list) {
-		if (req->status) {
+		if (req->status == -ENODATA) {
 			src_in = (struct sockaddr_in *) &req->src_addr;
 			dst_in = (struct sockaddr_in *) &req->dst_addr;
 			req->status = addr_resolve_remote(src_in, dst_in,
 							  req->addr);
+			if (req->status && time_after_eq(jiffies, req->timeout))
+				req->status = -ETIMEDOUT;
+			else if (req->status == -ENODATA)
+				continue;
 		}
-		if (req->status && time_after(jiffies, req->timeout))
-			req->status = -ETIMEDOUT;
-		else if (req->status == -ENODATA)
-			continue;
-
-		list_del(&req->list);
-		list_add_tail(&req->list, &done_list);
+		list_move_tail(&req->list, &done_list);
 	}
 
 	if (!list_empty(&req_list)) {
@@ -347,8 +345,7 @@
 		if (req->addr == addr) {
 			req->status = -ECANCELED;
 			req->timeout = jiffies;
-			list_del(&req->list);
-			list_add(&req->list, &req_list);
+			list_move(&req->list, &req_list);
 			set_timeout(req->timeout);
 			break;
 		}
diff --git a/drivers/infiniband/core/cm.c b/drivers/infiniband/core/cm.c
index 25b1018..e5dc453 100644
--- a/drivers/infiniband/core/cm.c
+++ b/drivers/infiniband/core/cm.c
@@ -147,12 +147,12 @@
 	__be32 rq_psn;
 	int timeout_ms;
 	enum ib_mtu path_mtu;
+	__be16 pkey;
 	u8 private_data_len;
 	u8 max_cm_retries;
 	u8 peer_to_peer;
 	u8 responder_resources;
 	u8 initiator_depth;
-	u8 local_ack_timeout;
 	u8 retry_count;
 	u8 rnr_retry_count;
 	u8 service_timeout;
@@ -240,11 +240,10 @@
 	if (!private_data || !private_data_len)
 		return NULL;
 
-	data = kmalloc(private_data_len, GFP_KERNEL);
+	data = kmemdup(private_data, private_data_len, GFP_KERNEL);
 	if (!data)
 		return ERR_PTR(-ENOMEM);
 
-	memcpy(data, private_data, private_data_len);
 	return data;
 }
 
@@ -691,7 +690,7 @@
 	 * timewait before notifying the user that we've exited timewait.
 	 */
 	cm_id_priv->id.state = IB_CM_TIMEWAIT;
-	wait_time = cm_convert_to_ms(cm_id_priv->local_ack_timeout);
+	wait_time = cm_convert_to_ms(cm_id_priv->av.packet_life_time + 1);
 	queue_delayed_work(cm.wq, &cm_id_priv->timewait_info->work.work,
 			   msecs_to_jiffies(wait_time));
 	cm_id_priv->timewait_info = NULL;
@@ -1010,6 +1009,7 @@
 	cm_id_priv->responder_resources = param->responder_resources;
 	cm_id_priv->retry_count = param->retry_count;
 	cm_id_priv->path_mtu = param->primary_path->mtu;
+	cm_id_priv->pkey = param->primary_path->pkey;
 	cm_id_priv->qp_type = param->qp_type;
 
 	ret = cm_alloc_msg(cm_id_priv, &cm_id_priv->msg);
@@ -1024,8 +1024,6 @@
 
 	cm_id_priv->local_qpn = cm_req_get_local_qpn(req_msg);
 	cm_id_priv->rq_psn = cm_req_get_starting_psn(req_msg);
-	cm_id_priv->local_ack_timeout =
-				cm_req_get_primary_local_ack_timeout(req_msg);
 
 	spin_lock_irqsave(&cm_id_priv->lock, flags);
 	ret = ib_post_send_mad(cm_id_priv->msg, NULL);
@@ -1410,9 +1408,8 @@
 	cm_id_priv->initiator_depth = cm_req_get_resp_res(req_msg);
 	cm_id_priv->responder_resources = cm_req_get_init_depth(req_msg);
 	cm_id_priv->path_mtu = cm_req_get_path_mtu(req_msg);
+	cm_id_priv->pkey = req_msg->pkey;
 	cm_id_priv->sq_psn = cm_req_get_starting_psn(req_msg);
-	cm_id_priv->local_ack_timeout =
-				cm_req_get_primary_local_ack_timeout(req_msg);
 	cm_id_priv->retry_count = cm_req_get_retry_count(req_msg);
 	cm_id_priv->rnr_retry_count = cm_req_get_rnr_retry_count(req_msg);
 	cm_id_priv->qp_type = cm_req_get_qp_type(req_msg);
@@ -1716,7 +1713,7 @@
 	unsigned long flags;
 	int ret;
 
-	/* See comment in ib_cm_establish about lookup. */
+	/* See comment in cm_establish about lookup. */
 	cm_id_priv = cm_acquire_id(work->local_id, work->remote_id);
 	if (!cm_id_priv)
 		return -EINVAL;
@@ -2402,11 +2399,16 @@
 	cm_id_priv = container_of(cm_id, struct cm_id_private, id);
 	spin_lock_irqsave(&cm_id_priv->lock, flags);
 	if (cm_id->state != IB_CM_ESTABLISHED ||
-	    cm_id->lap_state != IB_CM_LAP_IDLE) {
+	    (cm_id->lap_state != IB_CM_LAP_UNINIT &&
+	     cm_id->lap_state != IB_CM_LAP_IDLE)) {
 		ret = -EINVAL;
 		goto out;
 	}
 
+	ret = cm_init_av_by_path(alternate_path, &cm_id_priv->alt_av);
+	if (ret)
+		goto out;
+
 	ret = cm_alloc_msg(cm_id_priv, &msg);
 	if (ret)
 		goto out;
@@ -2431,7 +2433,8 @@
 }
 EXPORT_SYMBOL(ib_send_cm_lap);
 
-static void cm_format_path_from_lap(struct ib_sa_path_rec *path,
+static void cm_format_path_from_lap(struct cm_id_private *cm_id_priv,
+				    struct ib_sa_path_rec *path,
 				    struct cm_lap_msg *lap_msg)
 {
 	memset(path, 0, sizeof *path);
@@ -2443,10 +2446,10 @@
 	path->hop_limit = lap_msg->alt_hop_limit;
 	path->traffic_class = cm_lap_get_traffic_class(lap_msg);
 	path->reversible = 1;
-	/* pkey is same as in REQ */
+	path->pkey = cm_id_priv->pkey;
 	path->sl = cm_lap_get_sl(lap_msg);
 	path->mtu_selector = IB_SA_EQ;
-	/* mtu is same as in REQ */
+	path->mtu = cm_id_priv->path_mtu;
 	path->rate_selector = IB_SA_EQ;
 	path->rate = cm_lap_get_packet_rate(lap_msg);
 	path->packet_life_time_selector = IB_SA_EQ;
@@ -2472,7 +2475,7 @@
 
 	param = &work->cm_event.param.lap_rcvd;
 	param->alternate_path = &work->path[0];
-	cm_format_path_from_lap(param->alternate_path, lap_msg);
+	cm_format_path_from_lap(cm_id_priv, param->alternate_path, lap_msg);
 	work->cm_event.private_data = &lap_msg->private_data;
 
 	spin_lock_irqsave(&cm_id_priv->lock, flags);
@@ -2480,6 +2483,7 @@
 		goto unlock;
 
 	switch (cm_id_priv->id.lap_state) {
+	case IB_CM_LAP_UNINIT:
 	case IB_CM_LAP_IDLE:
 		break;
 	case IB_CM_MRA_LAP_SENT:
@@ -2502,6 +2506,10 @@
 
 	cm_id_priv->id.lap_state = IB_CM_LAP_RCVD;
 	cm_id_priv->tid = lap_msg->hdr.tid;
+	cm_init_av_for_response(work->port, work->mad_recv_wc->wc,
+				work->mad_recv_wc->recv_buf.grh,
+				&cm_id_priv->av);
+	cm_init_av_by_path(param->alternate_path, &cm_id_priv->alt_av);
 	ret = atomic_inc_and_test(&cm_id_priv->work_count);
 	if (!ret)
 		list_add_tail(&work->list, &cm_id_priv->work_list);
@@ -3040,7 +3048,7 @@
 		cm_free_work(work);
 }
 
-int ib_cm_establish(struct ib_cm_id *cm_id)
+static int cm_establish(struct ib_cm_id *cm_id)
 {
 	struct cm_id_private *cm_id_priv;
 	struct cm_work *work;
@@ -3088,7 +3096,44 @@
 out:
 	return ret;
 }
-EXPORT_SYMBOL(ib_cm_establish);
+
+static int cm_migrate(struct ib_cm_id *cm_id)
+{
+	struct cm_id_private *cm_id_priv;
+	unsigned long flags;
+	int ret = 0;
+
+	cm_id_priv = container_of(cm_id, struct cm_id_private, id);
+	spin_lock_irqsave(&cm_id_priv->lock, flags);
+	if (cm_id->state == IB_CM_ESTABLISHED &&
+	    (cm_id->lap_state == IB_CM_LAP_UNINIT ||
+	     cm_id->lap_state == IB_CM_LAP_IDLE)) {
+		cm_id->lap_state = IB_CM_LAP_IDLE;
+		cm_id_priv->av = cm_id_priv->alt_av;
+	} else
+		ret = -EINVAL;
+	spin_unlock_irqrestore(&cm_id_priv->lock, flags);
+
+	return ret;
+}
+
+int ib_cm_notify(struct ib_cm_id *cm_id, enum ib_event_type event)
+{
+	int ret;
+
+	switch (event) {
+	case IB_EVENT_COMM_EST:
+		ret = cm_establish(cm_id);
+		break;
+	case IB_EVENT_PATH_MIG:
+		ret = cm_migrate(cm_id);
+		break;
+	default:
+		ret = -EINVAL;
+	}
+	return ret;
+}
+EXPORT_SYMBOL(ib_cm_notify);
 
 static void cm_recv_handler(struct ib_mad_agent *mad_agent,
 			    struct ib_mad_recv_wc *mad_recv_wc)
@@ -3173,8 +3218,7 @@
 	case IB_CM_ESTABLISHED:
 		*qp_attr_mask = IB_QP_STATE | IB_QP_ACCESS_FLAGS |
 				IB_QP_PKEY_INDEX | IB_QP_PORT;
-		qp_attr->qp_access_flags = IB_ACCESS_LOCAL_WRITE |
-					   IB_ACCESS_REMOTE_WRITE;
+		qp_attr->qp_access_flags = IB_ACCESS_REMOTE_WRITE;
 		if (cm_id_priv->responder_resources)
 			qp_attr->qp_access_flags |= IB_ACCESS_REMOTE_READ |
 						    IB_ACCESS_REMOTE_ATOMIC;
@@ -3222,6 +3266,9 @@
 		if (cm_id_priv->alt_av.ah_attr.dlid) {
 			*qp_attr_mask |= IB_QP_ALT_PATH;
 			qp_attr->alt_port_num = cm_id_priv->alt_av.port->port_num;
+			qp_attr->alt_pkey_index = cm_id_priv->alt_av.pkey_index;
+			qp_attr->alt_timeout =
+					cm_id_priv->alt_av.packet_life_time + 1;
 			qp_attr->alt_ah_attr = cm_id_priv->alt_av.ah_attr;
 		}
 		ret = 0;
@@ -3248,19 +3295,31 @@
 	case IB_CM_REP_SENT:
 	case IB_CM_MRA_REP_RCVD:
 	case IB_CM_ESTABLISHED:
-		*qp_attr_mask = IB_QP_STATE | IB_QP_SQ_PSN;
-		qp_attr->sq_psn = be32_to_cpu(cm_id_priv->sq_psn);
-		if (cm_id_priv->qp_type == IB_QPT_RC) {
-			*qp_attr_mask |= IB_QP_TIMEOUT | IB_QP_RETRY_CNT |
-					 IB_QP_RNR_RETRY |
-					 IB_QP_MAX_QP_RD_ATOMIC;
-			qp_attr->timeout = cm_id_priv->local_ack_timeout;
-			qp_attr->retry_cnt = cm_id_priv->retry_count;
-			qp_attr->rnr_retry = cm_id_priv->rnr_retry_count;
-			qp_attr->max_rd_atomic = cm_id_priv->initiator_depth;
-		}
-		if (cm_id_priv->alt_av.ah_attr.dlid) {
-			*qp_attr_mask |= IB_QP_PATH_MIG_STATE;
+		if (cm_id_priv->id.lap_state == IB_CM_LAP_UNINIT) {
+			*qp_attr_mask = IB_QP_STATE | IB_QP_SQ_PSN;
+			qp_attr->sq_psn = be32_to_cpu(cm_id_priv->sq_psn);
+			if (cm_id_priv->qp_type == IB_QPT_RC) {
+				*qp_attr_mask |= IB_QP_TIMEOUT | IB_QP_RETRY_CNT |
+						 IB_QP_RNR_RETRY |
+						 IB_QP_MAX_QP_RD_ATOMIC;
+				qp_attr->timeout =
+					cm_id_priv->av.packet_life_time + 1;
+				qp_attr->retry_cnt = cm_id_priv->retry_count;
+				qp_attr->rnr_retry = cm_id_priv->rnr_retry_count;
+				qp_attr->max_rd_atomic =
+					cm_id_priv->initiator_depth;
+			}
+			if (cm_id_priv->alt_av.ah_attr.dlid) {
+				*qp_attr_mask |= IB_QP_PATH_MIG_STATE;
+				qp_attr->path_mig_state = IB_MIG_REARM;
+			}
+		} else {
+			*qp_attr_mask = IB_QP_ALT_PATH | IB_QP_PATH_MIG_STATE;
+			qp_attr->alt_port_num = cm_id_priv->alt_av.port->port_num;
+			qp_attr->alt_pkey_index = cm_id_priv->alt_av.pkey_index;
+			qp_attr->alt_timeout =
+				cm_id_priv->alt_av.packet_life_time + 1;
+			qp_attr->alt_ah_attr = cm_id_priv->alt_av.ah_attr;
 			qp_attr->path_mig_state = IB_MIG_REARM;
 		}
 		ret = 0;
diff --git a/drivers/infiniband/core/cma.c b/drivers/infiniband/core/cma.c
index 845090b..cf48f26 100644
--- a/drivers/infiniband/core/cma.c
+++ b/drivers/infiniband/core/cma.c
@@ -344,7 +344,7 @@
 		return ret;
 
 	qp_attr.qp_state = IB_QPS_INIT;
-	qp_attr.qp_access_flags = IB_ACCESS_LOCAL_WRITE;
+	qp_attr.qp_access_flags = 0;
 	qp_attr.port_num = id_priv->id.port_num;
 	return ib_modify_qp(qp, &qp_attr, IB_QP_STATE | IB_QP_ACCESS_FLAGS |
 					  IB_QP_PKEY_INDEX | IB_QP_PORT);
@@ -935,13 +935,8 @@
 	mutex_lock(&lock);
 	ret = cma_acquire_dev(conn_id);
 	mutex_unlock(&lock);
-	if (ret) {
-		ret = -ENODEV;
-		cma_exch(conn_id, CMA_DESTROYING);
-		cma_release_remove(conn_id);
-		rdma_destroy_id(&conn_id->id);
-		goto out;
-	}
+	if (ret)
+		goto release_conn_id;
 
 	conn_id->cm_id.ib = cm_id;
 	cm_id->context = conn_id;
@@ -951,13 +946,17 @@
 	ret = cma_notify_user(conn_id, RDMA_CM_EVENT_CONNECT_REQUEST, 0,
 			      ib_event->private_data + offset,
 			      IB_CM_REQ_PRIVATE_DATA_SIZE - offset);
-	if (ret) {
-		/* Destroy the CM ID by returning a non-zero value. */
-		conn_id->cm_id.ib = NULL;
-		cma_exch(conn_id, CMA_DESTROYING);
-		cma_release_remove(conn_id);
-		rdma_destroy_id(&conn_id->id);
-	}
+	if (!ret)
+		goto out;
+
+	/* Destroy the CM ID by returning a non-zero value. */
+	conn_id->cm_id.ib = NULL;
+
+release_conn_id:
+	cma_exch(conn_id, CMA_DESTROYING);
+	cma_release_remove(conn_id);
+	rdma_destroy_id(&conn_id->id);
+
 out:
 	cma_release_remove(listen_id);
 	return ret;
@@ -1481,19 +1480,18 @@
 	u8 p;
 
 	mutex_lock(&lock);
-	list_for_each_entry(cma_dev, &dev_list, list)
-		for (p = 1; p <= cma_dev->device->phys_port_cnt; ++p)
-			if (!ib_query_port (cma_dev->device, p, &port_attr) &&
-			    port_attr.state == IB_PORT_ACTIVE)
-				goto port_found;
-
-	if (!list_empty(&dev_list)) {
-		p = 1;
-		cma_dev = list_entry(dev_list.next, struct cma_device, list);
-	} else {
+	if (list_empty(&dev_list)) {
 		ret = -ENODEV;
 		goto out;
 	}
+	list_for_each_entry(cma_dev, &dev_list, list)
+		for (p = 1; p <= cma_dev->device->phys_port_cnt; ++p)
+			if (!ib_query_port(cma_dev->device, p, &port_attr) &&
+			    port_attr.state == IB_PORT_ACTIVE)
+				goto port_found;
+
+	p = 1;
+	cma_dev = list_entry(dev_list.next, struct cma_device, list);
 
 port_found:
 	ret = ib_get_cached_gid(cma_dev->device, p, 0, &gid);
@@ -2123,8 +2121,6 @@
 
 	cma_dev->device = device;
 	cma_dev->node_guid = device->node_guid;
-	if (!cma_dev->node_guid)
-		goto err;
 
 	init_completion(&cma_dev->comp);
 	atomic_set(&cma_dev->refcount, 1);
@@ -2136,9 +2132,6 @@
 	list_for_each_entry(id_priv, &listen_any_list, list)
 		cma_listen_on_dev(id_priv, cma_dev);
 	mutex_unlock(&lock);
-	return;
-err:
-	kfree(cma_dev);
 }
 
 static int cma_remove_id_dev(struct rdma_id_private *id_priv)
diff --git a/drivers/infiniband/core/iwcm.c b/drivers/infiniband/core/iwcm.c
index c3fb304..cf797d7 100644
--- a/drivers/infiniband/core/iwcm.c
+++ b/drivers/infiniband/core/iwcm.c
@@ -80,7 +80,7 @@
  * 1) in the event upcall, cm_event_handler(), for a listening cm_id.  If
  *    the backlog is exceeded, then no more connection request events will
  *    be processed.  cm_event_handler() returns -ENOMEM in this case.  Its up
- *    to the provider to reject the connectino request.
+ *    to the provider to reject the connection request.
  * 2) in the connection request workqueue handler, cm_conn_req_handler().
  *    If work elements cannot be allocated for the new connect request cm_id,
  *    then IWCM will call the provider reject method.  This is ok since
@@ -131,26 +131,25 @@
 }
 
 /*
- * Save private data from incoming connection requests in the
- * cm_id_priv so the low level driver doesn't have to.  Adjust
+ * Save private data from incoming connection requests to
+ * iw_cm_event, so the low level driver doesn't have to. Adjust
  * the event ptr to point to the local copy.
  */
-static int copy_private_data(struct iwcm_id_private *cm_id_priv,
-		       struct iw_cm_event *event)
+static int copy_private_data(struct iw_cm_event *event)
 {
 	void *p;
 
-	p = kmalloc(event->private_data_len, GFP_ATOMIC);
+	p = kmemdup(event->private_data, event->private_data_len, GFP_ATOMIC);
 	if (!p)
 		return -ENOMEM;
-	memcpy(p, event->private_data, event->private_data_len);
 	event->private_data = p;
 	return 0;
 }
 
 /*
- * Release a reference on cm_id. If the last reference is being removed
- * and iw_destroy_cm_id is waiting, wake up the waiting thread.
+ * Release a reference on cm_id. If the last reference is being
+ * released, enable the waiting thread (in iw_destroy_cm_id) to
+ * get woken up, and return 1 if a thread is already waiting.
  */
 static int iwcm_deref_id(struct iwcm_id_private *cm_id_priv)
 {
@@ -243,7 +242,7 @@
 /*
  * CM_ID <-- CLOSING
  *
- * Block if a passive or active connection is currenlty being processed. Then
+ * Block if a passive or active connection is currently being processed. Then
  * process the event as follows:
  * - If we are ESTABLISHED, move to CLOSING and modify the QP state
  *   based on the abrupt flag
@@ -408,7 +407,7 @@
 {
 	struct iwcm_id_private *cm_id_priv;
 	unsigned long flags;
-	int ret = 0;
+	int ret;
 
 	cm_id_priv = container_of(cm_id, struct iwcm_id_private, id);
 
@@ -535,7 +534,7 @@
 int iw_cm_connect(struct iw_cm_id *cm_id, struct iw_cm_conn_param *iw_param)
 {
 	struct iwcm_id_private *cm_id_priv;
-	int ret = 0;
+	int ret;
 	unsigned long flags;
 	struct ib_qp *qp;
 
@@ -620,7 +619,7 @@
 	spin_lock_irqsave(&listen_id_priv->lock, flags);
 	if (listen_id_priv->state != IW_CM_STATE_LISTEN) {
 		spin_unlock_irqrestore(&listen_id_priv->lock, flags);
-		return;
+		goto out;
 	}
 	spin_unlock_irqrestore(&listen_id_priv->lock, flags);
 
@@ -629,7 +628,7 @@
 				listen_id_priv->id.context);
 	/* If the cm_id could not be created, ignore the request */
 	if (IS_ERR(cm_id))
-		return;
+		goto out;
 
 	cm_id->provider_data = iw_event->provider_data;
 	cm_id->local_addr = iw_event->local_addr;
@@ -642,7 +641,7 @@
 	if (ret) {
 		iw_cm_reject(cm_id, NULL, 0);
 		iw_destroy_cm_id(cm_id);
-		return;
+		goto out;
 	}
 
 	/* Call the client CM handler */
@@ -654,6 +653,7 @@
 			kfree(cm_id);
 	}
 
+out:
 	if (iw_event->private_data_len)
 		kfree(iw_event->private_data);
 }
@@ -674,7 +674,7 @@
 			       struct iw_cm_event *iw_event)
 {
 	unsigned long flags;
-	int ret = 0;
+	int ret;
 
 	spin_lock_irqsave(&cm_id_priv->lock, flags);
 
@@ -704,7 +704,7 @@
 			       struct iw_cm_event *iw_event)
 {
 	unsigned long flags;
-	int ret = 0;
+	int ret;
 
 	spin_lock_irqsave(&cm_id_priv->lock, flags);
 	/*
@@ -830,7 +830,8 @@
  */
 static void cm_work_handler(void *arg)
 {
-	struct iwcm_work *work = arg, lwork;
+	struct iwcm_work *work = arg;
+	struct iw_cm_event levent;
 	struct iwcm_id_private *cm_id_priv = work->cm_id;
 	unsigned long flags;
 	int empty;
@@ -843,11 +844,11 @@
 				  struct iwcm_work, list);
 		list_del_init(&work->list);
 		empty = list_empty(&cm_id_priv->work_list);
-		lwork = *work;
+		levent = work->event;
 		put_work(work);
 		spin_unlock_irqrestore(&cm_id_priv->lock, flags);
 
-		ret = process_event(cm_id_priv, &work->event);
+		ret = process_event(cm_id_priv, &levent);
 		if (ret) {
 			set_bit(IWCM_F_CALLBACK_DESTROY, &cm_id_priv->flags);
 			destroy_cm_id(&cm_id_priv->id);
@@ -906,7 +907,7 @@
 	if ((work->event.event == IW_CM_EVENT_CONNECT_REQUEST ||
 	     work->event.event == IW_CM_EVENT_CONNECT_REPLY) &&
 	    work->event.private_data_len) {
-		ret = copy_private_data(cm_id_priv, &work->event);
+		ret = copy_private_data(&work->event);
 		if (ret) {
 			put_work(work);
 			goto out;
diff --git a/drivers/infiniband/core/mad.c b/drivers/infiniband/core/mad.c
index a72bcea..3f9c162 100644
--- a/drivers/infiniband/core/mad.c
+++ b/drivers/infiniband/core/mad.c
@@ -46,7 +46,7 @@
 MODULE_AUTHOR("Hal Rosenstock");
 MODULE_AUTHOR("Sean Hefty");
 
-static kmem_cache_t *ib_mad_cache;
+static struct kmem_cache *ib_mad_cache;
 
 static struct list_head ib_mad_port_list;
 static u32 ib_mad_client_id = 0;
diff --git a/drivers/infiniband/core/ucm.c b/drivers/infiniband/core/ucm.c
index ad4f4d5..f15220a 100644
--- a/drivers/infiniband/core/ucm.c
+++ b/drivers/infiniband/core/ucm.c
@@ -161,12 +161,14 @@
 				    struct ib_ucm_event, ctx_list);
 		list_del(&uevent->file_list);
 		list_del(&uevent->ctx_list);
+		mutex_unlock(&ctx->file->file_mutex);
 
 		/* clear incoming connections. */
 		if (ib_ucm_new_cm_id(uevent->resp.event))
 			ib_destroy_cm_id(uevent->cm_id);
 
 		kfree(uevent);
+		mutex_lock(&ctx->file->file_mutex);
 	}
 	mutex_unlock(&ctx->file->file_mutex);
 }
@@ -328,20 +330,18 @@
 	}
 
 	if (uvt->data_len) {
-		uvt->data = kmalloc(uvt->data_len, GFP_KERNEL);
+		uvt->data = kmemdup(evt->private_data, uvt->data_len, GFP_KERNEL);
 		if (!uvt->data)
 			goto err1;
 
-		memcpy(uvt->data, evt->private_data, uvt->data_len);
 		uvt->resp.present |= IB_UCM_PRES_DATA;
 	}
 
 	if (uvt->info_len) {
-		uvt->info = kmalloc(uvt->info_len, GFP_KERNEL);
+		uvt->info = kmemdup(info, uvt->info_len, GFP_KERNEL);
 		if (!uvt->info)
 			goto err2;
 
-		memcpy(uvt->info, info, uvt->info_len);
 		uvt->resp.present |= IB_UCM_PRES_INFO;
 	}
 	return 0;
@@ -685,11 +685,11 @@
 	return result;
 }
 
-static ssize_t ib_ucm_establish(struct ib_ucm_file *file,
-				const char __user *inbuf,
-				int in_len, int out_len)
+static ssize_t ib_ucm_notify(struct ib_ucm_file *file,
+			     const char __user *inbuf,
+			     int in_len, int out_len)
 {
-	struct ib_ucm_establish cmd;
+	struct ib_ucm_notify cmd;
 	struct ib_ucm_context *ctx;
 	int result;
 
@@ -700,7 +700,7 @@
 	if (IS_ERR(ctx))
 		return PTR_ERR(ctx);
 
-	result = ib_cm_establish(ctx->cm_id);
+	result = ib_cm_notify(ctx->cm_id, (enum ib_event_type) cmd.event);
 	ib_ucm_ctx_put(ctx);
 	return result;
 }
@@ -1107,7 +1107,7 @@
 	[IB_USER_CM_CMD_DESTROY_ID]    = ib_ucm_destroy_id,
 	[IB_USER_CM_CMD_ATTR_ID]       = ib_ucm_attr_id,
 	[IB_USER_CM_CMD_LISTEN]        = ib_ucm_listen,
-	[IB_USER_CM_CMD_ESTABLISH]     = ib_ucm_establish,
+	[IB_USER_CM_CMD_NOTIFY]        = ib_ucm_notify,
 	[IB_USER_CM_CMD_SEND_REQ]      = ib_ucm_send_req,
 	[IB_USER_CM_CMD_SEND_REP]      = ib_ucm_send_rep,
 	[IB_USER_CM_CMD_SEND_RTU]      = ib_ucm_send_rtu,
diff --git a/drivers/infiniband/hw/amso1100/c2.h b/drivers/infiniband/hw/amso1100/c2.h
index 1b17dcd..04a9db5 100644
--- a/drivers/infiniband/hw/amso1100/c2.h
+++ b/drivers/infiniband/hw/amso1100/c2.h
@@ -302,7 +302,7 @@
 	unsigned long pa;	/* PA device memory */
 	void **qptr_array;
 
-	kmem_cache_t *host_msg_cache;
+	struct kmem_cache *host_msg_cache;
 
 	struct list_head cca_link;		/* adapter list */
 	struct list_head eh_wakeup_list;	/* event wakeup list */
diff --git a/drivers/infiniband/hw/amso1100/c2_qp.c b/drivers/infiniband/hw/amso1100/c2_qp.c
index 5bcf697..179d005 100644
--- a/drivers/infiniband/hw/amso1100/c2_qp.c
+++ b/drivers/infiniband/hw/amso1100/c2_qp.c
@@ -564,6 +564,32 @@
 	return err;
 }
 
+static inline void c2_lock_cqs(struct c2_cq *send_cq, struct c2_cq *recv_cq)
+{
+	if (send_cq == recv_cq)
+		spin_lock_irq(&send_cq->lock);
+	else if (send_cq > recv_cq) {
+		spin_lock_irq(&send_cq->lock);
+		spin_lock_nested(&recv_cq->lock, SINGLE_DEPTH_NESTING);
+	} else {
+		spin_lock_irq(&recv_cq->lock);
+		spin_lock_nested(&send_cq->lock, SINGLE_DEPTH_NESTING);
+	}
+}
+
+static inline void c2_unlock_cqs(struct c2_cq *send_cq, struct c2_cq *recv_cq)
+{
+	if (send_cq == recv_cq)
+		spin_unlock_irq(&send_cq->lock);
+	else if (send_cq > recv_cq) {
+		spin_unlock(&recv_cq->lock);
+		spin_unlock_irq(&send_cq->lock);
+	} else {
+		spin_unlock(&send_cq->lock);
+		spin_unlock_irq(&recv_cq->lock);
+	}
+}
+
 void c2_free_qp(struct c2_dev *c2dev, struct c2_qp *qp)
 {
 	struct c2_cq *send_cq;
@@ -576,15 +602,9 @@
 	 * Lock CQs here, so that CQ polling code can do QP lookup
 	 * without taking a lock.
 	 */
-	spin_lock_irq(&send_cq->lock);
-	if (send_cq != recv_cq)
-		spin_lock(&recv_cq->lock);
-
+	c2_lock_cqs(send_cq, recv_cq);
 	c2_free_qpn(c2dev, qp->qpn);
-
-	if (send_cq != recv_cq)
-		spin_unlock(&recv_cq->lock);
-	spin_unlock_irq(&send_cq->lock);
+	c2_unlock_cqs(send_cq, recv_cq);
 
 	/*
 	 * Destory qp in the rnic...
diff --git a/drivers/infiniband/hw/amso1100/c2_rnic.c b/drivers/infiniband/hw/amso1100/c2_rnic.c
index 623dc95..1687c51 100644
--- a/drivers/infiniband/hw/amso1100/c2_rnic.c
+++ b/drivers/infiniband/hw/amso1100/c2_rnic.c
@@ -441,7 +441,7 @@
  * involves initalizing the various limits and resouce pools that
  * comprise the RNIC instance.
  */
-int c2_rnic_init(struct c2_dev *c2dev)
+int __devinit c2_rnic_init(struct c2_dev *c2dev)
 {
 	int err;
 	u32 qsize, msgsize;
@@ -611,7 +611,7 @@
 /*
  * Called by c2_remove to cleanup the RNIC resources.
  */
-void c2_rnic_term(struct c2_dev *c2dev)
+void __devexit c2_rnic_term(struct c2_dev *c2dev)
 {
 
 	/* Close the open adapter instance */
diff --git a/drivers/infiniband/hw/ehca/ehca_main.c b/drivers/infiniband/hw/ehca/ehca_main.c
index 01f5aa9..3d1c1c5 100644
--- a/drivers/infiniband/hw/ehca/ehca_main.c
+++ b/drivers/infiniband/hw/ehca/ehca_main.c
@@ -52,7 +52,7 @@
 MODULE_LICENSE("Dual BSD/GPL");
 MODULE_AUTHOR("Christoph Raisch <raisch@de.ibm.com>");
 MODULE_DESCRIPTION("IBM eServer HCA InfiniBand Device Driver");
-MODULE_VERSION("SVNEHCA_0018");
+MODULE_VERSION("SVNEHCA_0019");
 
 int ehca_open_aqp1     = 0;
 int ehca_debug_level   = 0;
@@ -790,7 +790,7 @@
 	int ret;
 
 	printk(KERN_INFO "eHCA Infiniband Device Driver "
-	                 "(Rel.: SVNEHCA_0018)\n");
+	                 "(Rel.: SVNEHCA_0019)\n");
 	idr_init(&ehca_qp_idr);
 	idr_init(&ehca_cq_idr);
 	spin_lock_init(&ehca_qp_idr_lock);
diff --git a/drivers/infiniband/hw/ehca/ehca_qp.c b/drivers/infiniband/hw/ehca/ehca_qp.c
index cf3e50e..8682aa5 100644
--- a/drivers/infiniband/hw/ehca/ehca_qp.c
+++ b/drivers/infiniband/hw/ehca/ehca_qp.c
@@ -732,8 +732,7 @@
 	u64 h_ret;
 	struct ipz_queue *squeue;
 	void *bad_send_wqe_p, *bad_send_wqe_v;
-	void *squeue_start_p, *squeue_end_p;
-	void *squeue_start_v, *squeue_end_v;
+	u64 q_ofs;
 	struct ehca_wqe *wqe;
 	int qp_num = my_qp->ib_qp.qp_num;
 
@@ -755,26 +754,23 @@
 	if (ehca_debug_level)
 		ehca_dmp(bad_send_wqe_v, 32, "qp_num=%x bad_wqe", qp_num);
 	squeue = &my_qp->ipz_squeue;
-	squeue_start_p = (void*)virt_to_abs(ipz_qeit_calc(squeue, 0L));
-	squeue_end_p = squeue_start_p+squeue->queue_length;
-	squeue_start_v = abs_to_virt((u64)squeue_start_p);
-	squeue_end_v = abs_to_virt((u64)squeue_end_p);
-	ehca_dbg(&shca->ib_device, "qp_num=%x squeue_start_v=%p squeue_end_v=%p",
-		 qp_num, squeue_start_v, squeue_end_v);
+	if (ipz_queue_abs_to_offset(squeue, (u64)bad_send_wqe_p, &q_ofs)) {
+		ehca_err(&shca->ib_device, "failed to get wqe offset qp_num=%x"
+			 " bad_send_wqe_p=%p", qp_num, bad_send_wqe_p);
+		return -EFAULT;
+	}
 
 	/* loop sets wqe's purge bit */
-	wqe = (struct ehca_wqe*)bad_send_wqe_v;
+	wqe = (struct ehca_wqe*)ipz_qeit_calc(squeue, q_ofs);
 	*bad_wqe_cnt = 0;
 	while (wqe->optype != 0xff && wqe->wqef != 0xff) {
 		if (ehca_debug_level)
 			ehca_dmp(wqe, 32, "qp_num=%x wqe", qp_num);
 		wqe->nr_of_data_seg = 0; /* suppress data access */
 		wqe->wqef = WQEF_PURGE; /* WQE to be purged */
-		wqe = (struct ehca_wqe*)((u8*)wqe+squeue->qe_size);
+		q_ofs = ipz_queue_advance_offset(squeue, q_ofs);
+		wqe = (struct ehca_wqe*)ipz_qeit_calc(squeue, q_ofs);
 		*bad_wqe_cnt = (*bad_wqe_cnt)+1;
-		if ((void*)wqe >= squeue_end_v) {
-			wqe = squeue_start_v;
-		}
 	}
 	/*
 	 * bad wqe will be reprocessed and ignored when pol_cq() is called,
diff --git a/drivers/infiniband/hw/ehca/ipz_pt_fn.c b/drivers/infiniband/hw/ehca/ipz_pt_fn.c
index e028ff1..bf7a400 100644
--- a/drivers/infiniband/hw/ehca/ipz_pt_fn.c
+++ b/drivers/infiniband/hw/ehca/ipz_pt_fn.c
@@ -70,6 +70,19 @@
 	return ret;
 }
 
+int ipz_queue_abs_to_offset(struct ipz_queue *queue, u64 addr, u64 *q_offset)
+{
+	int i;
+	for (i = 0; i < queue->queue_length / queue->pagesize; i++) {
+		u64 page = (u64)virt_to_abs(queue->queue_pages[i]);
+		if (addr >= page && addr < page + queue->pagesize) {
+			*q_offset = addr - page + i * queue->pagesize;
+			return 0;
+		}
+	}
+	return -EINVAL;
+}
+
 int ipz_queue_ctor(struct ipz_queue *queue,
 		   const u32 nr_of_pages,
 		   const u32 pagesize, const u32 qe_size, const u32 nr_of_sg)
diff --git a/drivers/infiniband/hw/ehca/ipz_pt_fn.h b/drivers/infiniband/hw/ehca/ipz_pt_fn.h
index 2f13509..dc3bda2 100644
--- a/drivers/infiniband/hw/ehca/ipz_pt_fn.h
+++ b/drivers/infiniband/hw/ehca/ipz_pt_fn.h
@@ -150,6 +150,21 @@
 	return ipz_qeit_get(queue);
 }
 
+/*
+ * return the q_offset corresponding to an absolute address
+ */
+int ipz_queue_abs_to_offset(struct ipz_queue *queue, u64 addr, u64 *q_offset);
+
+/*
+ * return the next queue offset. don't modify the queue.
+ */
+static inline u64 ipz_queue_advance_offset(struct ipz_queue *queue, u64 offset)
+{
+	offset += queue->qe_size;
+	if (offset >= queue->queue_length) offset = 0;
+	return offset;
+}
+
 /* struct generic page table */
 struct ipz_pt {
 	u64 entries[EHCA_PT_ENTRIES];
diff --git a/drivers/infiniband/hw/ipath/ipath_verbs.c b/drivers/infiniband/hw/ipath/ipath_verbs.c
index a545610..acdee33 100644
--- a/drivers/infiniband/hw/ipath/ipath_verbs.c
+++ b/drivers/infiniband/hw/ipath/ipath_verbs.c
@@ -1487,7 +1487,7 @@
 	idev->pma_counter_select[1] = IB_PMA_PORT_RCV_DATA;
 	idev->pma_counter_select[2] = IB_PMA_PORT_XMIT_PKTS;
 	idev->pma_counter_select[3] = IB_PMA_PORT_RCV_PKTS;
-	idev->pma_counter_select[5] = IB_PMA_PORT_XMIT_WAIT;
+	idev->pma_counter_select[4] = IB_PMA_PORT_XMIT_WAIT;
 	idev->link_width_enabled = 3;	/* 1x or 4x */
 
 	/* Snapshot current HW counters to "clear" them. */
diff --git a/drivers/infiniband/hw/mthca/mthca_av.c b/drivers/infiniband/hw/mthca/mthca_av.c
index 6959945..57cdc1b 100644
--- a/drivers/infiniband/hw/mthca/mthca_av.c
+++ b/drivers/infiniband/hw/mthca/mthca_av.c
@@ -33,7 +33,6 @@
  * $Id: mthca_av.c 1349 2004-12-16 21:09:43Z roland $
  */
 
-#include <linux/init.h>
 #include <linux/string.h>
 #include <linux/slab.h>
 
@@ -323,7 +322,7 @@
 	return 0;
 }
 
-int __devinit mthca_init_av_table(struct mthca_dev *dev)
+int mthca_init_av_table(struct mthca_dev *dev)
 {
 	int err;
 
diff --git a/drivers/infiniband/hw/mthca/mthca_cq.c b/drivers/infiniband/hw/mthca/mthca_cq.c
index 149b369..283d50b 100644
--- a/drivers/infiniband/hw/mthca/mthca_cq.c
+++ b/drivers/infiniband/hw/mthca/mthca_cq.c
@@ -36,7 +36,6 @@
  * $Id: mthca_cq.c 1369 2004-12-20 16:17:07Z roland $
  */
 
-#include <linux/init.h>
 #include <linux/hardirq.h>
 
 #include <asm/io.h>
@@ -970,7 +969,7 @@
 	mthca_free_mailbox(dev, mailbox);
 }
 
-int __devinit mthca_init_cq_table(struct mthca_dev *dev)
+int mthca_init_cq_table(struct mthca_dev *dev)
 {
 	int err;
 
diff --git a/drivers/infiniband/hw/mthca/mthca_eq.c b/drivers/infiniband/hw/mthca/mthca_eq.c
index e284e06..8ec9fa1 100644
--- a/drivers/infiniband/hw/mthca/mthca_eq.c
+++ b/drivers/infiniband/hw/mthca/mthca_eq.c
@@ -33,7 +33,6 @@
  * $Id: mthca_eq.c 1382 2004-12-24 02:21:02Z roland $
  */
 
-#include <linux/init.h>
 #include <linux/errno.h>
 #include <linux/interrupt.h>
 #include <linux/pci.h>
@@ -479,10 +478,10 @@
 	return IRQ_HANDLED;
 }
 
-static int __devinit mthca_create_eq(struct mthca_dev *dev,
-				     int nent,
-				     u8 intr,
-				     struct mthca_eq *eq)
+static int mthca_create_eq(struct mthca_dev *dev,
+			   int nent,
+			   u8 intr,
+			   struct mthca_eq *eq)
 {
 	int npages;
 	u64 *dma_list = NULL;
@@ -664,9 +663,9 @@
 				 dev->eq_table.eq + i);
 }
 
-static int __devinit mthca_map_reg(struct mthca_dev *dev,
-				   unsigned long offset, unsigned long size,
-				   void __iomem **map)
+static int mthca_map_reg(struct mthca_dev *dev,
+			 unsigned long offset, unsigned long size,
+			 void __iomem **map)
 {
 	unsigned long base = pci_resource_start(dev->pdev, 0);
 
@@ -691,7 +690,7 @@
 	iounmap(map);
 }
 
-static int __devinit mthca_map_eq_regs(struct mthca_dev *dev)
+static int mthca_map_eq_regs(struct mthca_dev *dev)
 {
 	if (mthca_is_memfree(dev)) {
 		/*
@@ -781,7 +780,7 @@
 	}
 }
 
-int __devinit mthca_map_eq_icm(struct mthca_dev *dev, u64 icm_virt)
+int mthca_map_eq_icm(struct mthca_dev *dev, u64 icm_virt)
 {
 	int ret;
 	u8 status;
@@ -825,7 +824,7 @@
 	__free_page(dev->eq_table.icm_page);
 }
 
-int __devinit mthca_init_eq_table(struct mthca_dev *dev)
+int mthca_init_eq_table(struct mthca_dev *dev)
 {
 	int err;
 	u8 status;
diff --git a/drivers/infiniband/hw/mthca/mthca_mad.c b/drivers/infiniband/hw/mthca/mthca_mad.c
index 45e106f..acfa41d 100644
--- a/drivers/infiniband/hw/mthca/mthca_mad.c
+++ b/drivers/infiniband/hw/mthca/mthca_mad.c
@@ -317,7 +317,7 @@
 	return ret;
 }
 
-void __devexit mthca_free_agents(struct mthca_dev *dev)
+void mthca_free_agents(struct mthca_dev *dev)
 {
 	struct ib_mad_agent *agent;
 	int p, q;
diff --git a/drivers/infiniband/hw/mthca/mthca_main.c b/drivers/infiniband/hw/mthca/mthca_main.c
index 47ea021..0491ec7 100644
--- a/drivers/infiniband/hw/mthca/mthca_main.c
+++ b/drivers/infiniband/hw/mthca/mthca_main.c
@@ -98,7 +98,7 @@
 	.uarc_size	   = 1 << 18,	/* Arbel only */
 };
 
-static int __devinit mthca_tune_pci(struct mthca_dev *mdev)
+static int mthca_tune_pci(struct mthca_dev *mdev)
 {
 	int cap;
 	u16 val;
@@ -143,7 +143,7 @@
 	return 0;
 }
 
-static int __devinit mthca_dev_lim(struct mthca_dev *mdev, struct mthca_dev_lim *dev_lim)
+static int mthca_dev_lim(struct mthca_dev *mdev, struct mthca_dev_lim *dev_lim)
 {
 	int err;
 	u8 status;
@@ -255,7 +255,7 @@
 	return 0;
 }
 
-static int __devinit mthca_init_tavor(struct mthca_dev *mdev)
+static int mthca_init_tavor(struct mthca_dev *mdev)
 {
 	u8 status;
 	int err;
@@ -333,7 +333,7 @@
 	return err;
 }
 
-static int __devinit mthca_load_fw(struct mthca_dev *mdev)
+static int mthca_load_fw(struct mthca_dev *mdev)
 {
 	u8 status;
 	int err;
@@ -379,10 +379,10 @@
 	return err;
 }
 
-static int __devinit mthca_init_icm(struct mthca_dev *mdev,
-				    struct mthca_dev_lim *dev_lim,
-				    struct mthca_init_hca_param *init_hca,
-				    u64 icm_size)
+static int mthca_init_icm(struct mthca_dev *mdev,
+			  struct mthca_dev_lim *dev_lim,
+			  struct mthca_init_hca_param *init_hca,
+			  u64 icm_size)
 {
 	u64 aux_pages;
 	u8 status;
@@ -575,7 +575,7 @@
 	mthca_free_icm(mdev, mdev->fw.arbel.aux_icm);
 }
 
-static int __devinit mthca_init_arbel(struct mthca_dev *mdev)
+static int mthca_init_arbel(struct mthca_dev *mdev)
 {
 	struct mthca_dev_lim        dev_lim;
 	struct mthca_profile        profile;
@@ -683,7 +683,7 @@
 		mthca_SYS_DIS(mdev, &status);
 }
 
-static int __devinit mthca_init_hca(struct mthca_dev *mdev)
+static int mthca_init_hca(struct mthca_dev *mdev)
 {
 	u8 status;
 	int err;
@@ -720,7 +720,7 @@
 	return err;
 }
 
-static int __devinit mthca_setup_hca(struct mthca_dev *dev)
+static int mthca_setup_hca(struct mthca_dev *dev)
 {
 	int err;
 	u8 status;
@@ -875,8 +875,7 @@
 	return err;
 }
 
-static int __devinit mthca_request_regions(struct pci_dev *pdev,
-					   int ddr_hidden)
+static int mthca_request_regions(struct pci_dev *pdev, int ddr_hidden)
 {
 	int err;
 
@@ -928,7 +927,7 @@
 			   MTHCA_HCR_SIZE);
 }
 
-static int __devinit mthca_enable_msi_x(struct mthca_dev *mdev)
+static int mthca_enable_msi_x(struct mthca_dev *mdev)
 {
 	struct msix_entry entries[3];
 	int err;
@@ -1213,7 +1212,7 @@
 }
 
 static int __devinit mthca_init_one(struct pci_dev *pdev,
-			     const struct pci_device_id *id)
+				    const struct pci_device_id *id)
 {
 	static int mthca_version_printed = 0;
 	int ret;
diff --git a/drivers/infiniband/hw/mthca/mthca_mcg.c b/drivers/infiniband/hw/mthca/mthca_mcg.c
index 47ca8a9..a8ad072 100644
--- a/drivers/infiniband/hw/mthca/mthca_mcg.c
+++ b/drivers/infiniband/hw/mthca/mthca_mcg.c
@@ -32,7 +32,6 @@
  * $Id: mthca_mcg.c 1349 2004-12-16 21:09:43Z roland $
  */
 
-#include <linux/init.h>
 #include <linux/string.h>
 #include <linux/slab.h>
 
@@ -371,7 +370,7 @@
 	return err;
 }
 
-int __devinit mthca_init_mcg_table(struct mthca_dev *dev)
+int mthca_init_mcg_table(struct mthca_dev *dev)
 {
 	int err;
 	int table_size = dev->limits.num_mgms + dev->limits.num_amgms;
diff --git a/drivers/infiniband/hw/mthca/mthca_mr.c b/drivers/infiniband/hw/mthca/mthca_mr.c
index a486dec..f71ffa8 100644
--- a/drivers/infiniband/hw/mthca/mthca_mr.c
+++ b/drivers/infiniband/hw/mthca/mthca_mr.c
@@ -34,7 +34,6 @@
  */
 
 #include <linux/slab.h>
-#include <linux/init.h>
 #include <linux/errno.h>
 
 #include "mthca_dev.h"
@@ -135,7 +134,7 @@
 	spin_unlock(&buddy->lock);
 }
 
-static int __devinit mthca_buddy_init(struct mthca_buddy *buddy, int max_order)
+static int mthca_buddy_init(struct mthca_buddy *buddy, int max_order)
 {
 	int i, s;
 
@@ -759,7 +758,7 @@
 	*(u8 *) fmr->mem.arbel.mpt = MTHCA_MPT_STATUS_SW;
 }
 
-int __devinit mthca_init_mr_table(struct mthca_dev *dev)
+int mthca_init_mr_table(struct mthca_dev *dev)
 {
 	unsigned long addr;
 	int err, i;
diff --git a/drivers/infiniband/hw/mthca/mthca_pd.c b/drivers/infiniband/hw/mthca/mthca_pd.c
index 59df516..c1e9507 100644
--- a/drivers/infiniband/hw/mthca/mthca_pd.c
+++ b/drivers/infiniband/hw/mthca/mthca_pd.c
@@ -34,7 +34,6 @@
  * $Id: mthca_pd.c 1349 2004-12-16 21:09:43Z roland $
  */
 
-#include <linux/init.h>
 #include <linux/errno.h>
 
 #include "mthca_dev.h"
@@ -69,7 +68,7 @@
 	mthca_free(&dev->pd_table.alloc, pd->pd_num);
 }
 
-int __devinit mthca_init_pd_table(struct mthca_dev *dev)
+int mthca_init_pd_table(struct mthca_dev *dev)
 {
 	return mthca_alloc_init(&dev->pd_table.alloc,
 				dev->limits.num_pds,
diff --git a/drivers/infiniband/hw/mthca/mthca_provider.c b/drivers/infiniband/hw/mthca/mthca_provider.c
index fc67f78..21422a3 100644
--- a/drivers/infiniband/hw/mthca/mthca_provider.c
+++ b/drivers/infiniband/hw/mthca/mthca_provider.c
@@ -1100,11 +1100,10 @@
 	struct mthca_fmr *fmr;
 	int err;
 
-	fmr = kmalloc(sizeof *fmr, GFP_KERNEL);
+	fmr = kmemdup(fmr_attr, sizeof *fmr, GFP_KERNEL);
 	if (!fmr)
 		return ERR_PTR(-ENOMEM);
 
-	memcpy(&fmr->attr, fmr_attr, sizeof *fmr_attr);
 	err = mthca_fmr_alloc(to_mdev(pd->device), to_mpd(pd)->pd_num,
 			     convert_access(mr_access_flags), fmr);
 
diff --git a/drivers/infiniband/hw/mthca/mthca_qp.c b/drivers/infiniband/hw/mthca/mthca_qp.c
index 6a7822e..33e3ba7 100644
--- a/drivers/infiniband/hw/mthca/mthca_qp.c
+++ b/drivers/infiniband/hw/mthca/mthca_qp.c
@@ -35,7 +35,6 @@
  * $Id: mthca_qp.c 1355 2004-12-17 15:23:43Z roland $
  */
 
-#include <linux/init.h>
 #include <linux/string.h>
 #include <linux/slab.h>
 
@@ -2241,7 +2240,7 @@
 		*new_wqe = 0;
 }
 
-int __devinit mthca_init_qp_table(struct mthca_dev *dev)
+int mthca_init_qp_table(struct mthca_dev *dev)
 {
 	int err;
 	u8 status;
diff --git a/drivers/infiniband/hw/mthca/mthca_srq.c b/drivers/infiniband/hw/mthca/mthca_srq.c
index f5d7677..34d2c47 100644
--- a/drivers/infiniband/hw/mthca/mthca_srq.c
+++ b/drivers/infiniband/hw/mthca/mthca_srq.c
@@ -120,7 +120,7 @@
 
 	memset(context, 0, sizeof *context);
 
-	logsize = long_log2(srq->max) + srq->wqe_shift;
+	logsize = long_log2(srq->max);
 	context->state_logsize_srqn = cpu_to_be32(logsize << 24 | srq->srqn);
 	context->lkey = cpu_to_be32(srq->mr.ibmr.lkey);
 	context->db_index = cpu_to_be32(srq->db_index);
@@ -715,7 +715,7 @@
 		     sizeof (struct mthca_data_seg));
 }
 
-int __devinit mthca_init_srq_table(struct mthca_dev *dev)
+int mthca_init_srq_table(struct mthca_dev *dev)
 {
 	int err;
 
diff --git a/drivers/infiniband/ulp/ipoib/ipoib.h b/drivers/infiniband/ulp/ipoib/ipoib.h
index 0b8a79d..f2b6185 100644
--- a/drivers/infiniband/ulp/ipoib/ipoib.h
+++ b/drivers/infiniband/ulp/ipoib/ipoib.h
@@ -233,7 +233,7 @@
 }
 
 struct ipoib_neigh *ipoib_neigh_alloc(struct neighbour *neigh);
-void ipoib_neigh_free(struct ipoib_neigh *neigh);
+void ipoib_neigh_free(struct net_device *dev, struct ipoib_neigh *neigh);
 
 extern struct workqueue_struct *ipoib_workqueue;
 
diff --git a/drivers/infiniband/ulp/ipoib/ipoib_main.c b/drivers/infiniband/ulp/ipoib/ipoib_main.c
index 85522da..5ba3154 100644
--- a/drivers/infiniband/ulp/ipoib/ipoib_main.c
+++ b/drivers/infiniband/ulp/ipoib/ipoib_main.c
@@ -264,7 +264,7 @@
 		if (neigh->ah)
 			ipoib_put_ah(neigh->ah);
 
-		ipoib_neigh_free(neigh);
+		ipoib_neigh_free(dev, neigh);
 	}
 
 	spin_unlock_irqrestore(&priv->lock, flags);
@@ -525,10 +525,11 @@
 		ipoib_send(dev, skb, path->ah, IPOIB_QPN(skb->dst->neighbour->ha));
 	} else {
 		neigh->ah  = NULL;
-		__skb_queue_tail(&neigh->queue, skb);
 
 		if (!path->query && path_rec_start(dev, path))
 			goto err_list;
+
+		__skb_queue_tail(&neigh->queue, skb);
 	}
 
 	spin_unlock(&priv->lock);
@@ -538,7 +539,7 @@
 	list_del(&neigh->list);
 
 err_path:
-	ipoib_neigh_free(neigh);
+	ipoib_neigh_free(dev, neigh);
 	++priv->stats.tx_dropped;
 	dev_kfree_skb_any(skb);
 
@@ -655,7 +656,7 @@
 				 */
 				ipoib_put_ah(neigh->ah);
 				list_del(&neigh->list);
-				ipoib_neigh_free(neigh);
+				ipoib_neigh_free(dev, neigh);
 				spin_unlock(&priv->lock);
 				ipoib_path_lookup(skb, dev);
 				goto out;
@@ -786,7 +787,7 @@
 		if (neigh->ah)
 			ah = neigh->ah;
 		list_del(&neigh->list);
-		ipoib_neigh_free(neigh);
+		ipoib_neigh_free(n->dev, neigh);
 	}
 
 	spin_unlock_irqrestore(&priv->lock, flags);
@@ -809,9 +810,15 @@
 	return neigh;
 }
 
-void ipoib_neigh_free(struct ipoib_neigh *neigh)
+void ipoib_neigh_free(struct net_device *dev, struct ipoib_neigh *neigh)
 {
+	struct ipoib_dev_priv *priv = netdev_priv(dev);
+	struct sk_buff *skb;
 	*to_ipoib_neigh(neigh->neighbour) = NULL;
+	while ((skb = __skb_dequeue(&neigh->queue))) {
+		++priv->stats.tx_dropped;
+		dev_kfree_skb_any(skb);
+	}
 	kfree(neigh);
 }
 
diff --git a/drivers/infiniband/ulp/ipoib/ipoib_multicast.c b/drivers/infiniband/ulp/ipoib/ipoib_multicast.c
index 3faa182..d282d65 100644
--- a/drivers/infiniband/ulp/ipoib/ipoib_multicast.c
+++ b/drivers/infiniband/ulp/ipoib/ipoib_multicast.c
@@ -114,7 +114,7 @@
 		 */
 		if (neigh->ah)
 			ipoib_put_ah(neigh->ah);
-		ipoib_neigh_free(neigh);
+		ipoib_neigh_free(dev, neigh);
 	}
 
 	spin_unlock_irqrestore(&priv->lock, flags);
diff --git a/drivers/infiniband/ulp/iser/iscsi_iser.h b/drivers/infiniband/ulp/iser/iscsi_iser.h
index 9c53916..234e5b0 100644
--- a/drivers/infiniband/ulp/iser/iscsi_iser.h
+++ b/drivers/infiniband/ulp/iser/iscsi_iser.h
@@ -283,7 +283,7 @@
 	struct mutex      connlist_mutex;
 	struct list_head  connlist;		/* all iSER IB connections */
 
-	kmem_cache_t *desc_cache;
+	struct kmem_cache *desc_cache;
 };
 
 extern struct iser_global ig;
diff --git a/drivers/infiniband/ulp/srp/ib_srp.c b/drivers/infiniband/ulp/srp/ib_srp.c
index 4b09147..64ab5fc 100644
--- a/drivers/infiniband/ulp/srp/ib_srp.c
+++ b/drivers/infiniband/ulp/srp/ib_srp.c
@@ -1176,9 +1176,11 @@
 			break;
 		}
 
-		target->status = srp_alloc_iu_bufs(target);
-		if (target->status)
-			break;
+		if (!target->rx_ring[0]) {
+			target->status = srp_alloc_iu_bufs(target);
+			if (target->status)
+				break;
+		}
 
 		qp_attr = kmalloc(sizeof *qp_attr, GFP_KERNEL);
 		if (!qp_attr) {
@@ -1716,7 +1718,8 @@
 	if (!target_host)
 		return -ENOMEM;
 
-	target_host->max_lun = SRP_MAX_LUN;
+	target_host->max_lun     = SRP_MAX_LUN;
+	target_host->max_cmd_len = sizeof ((struct srp_cmd *) (void *) 0L)->cdb;
 
 	target = host_to_target(target_host);
 
diff --git a/drivers/input/joystick/iforce/iforce-usb.c b/drivers/input/joystick/iforce/iforce-usb.c
index 105112f..80cdebc 100644
--- a/drivers/input/joystick/iforce/iforce-usb.c
+++ b/drivers/input/joystick/iforce/iforce-usb.c
@@ -178,9 +178,9 @@
 
 fail:
 	if (iforce) {
-		if (iforce->irq) usb_free_urb(iforce->irq);
-		if (iforce->out) usb_free_urb(iforce->out);
-		if (iforce->ctrl) usb_free_urb(iforce->ctrl);
+		usb_free_urb(iforce->irq);
+		usb_free_urb(iforce->out);
+		usb_free_urb(iforce->ctrl);
 		kfree(iforce);
 	}
 
diff --git a/drivers/input/serio/serio_raw.c b/drivers/input/serio/serio_raw.c
index ba2a203..7c8d039 100644
--- a/drivers/input/serio/serio_raw.c
+++ b/drivers/input/serio/serio_raw.c
@@ -297,7 +297,7 @@
 
 	serio_raw->dev.minor = PSMOUSE_MINOR;
 	serio_raw->dev.name = serio_raw->name;
-	serio_raw->dev.dev = &serio->dev;
+	serio_raw->dev.parent = &serio->dev;
 	serio_raw->dev.fops = &serio_raw_fops;
 
 	err = misc_register(&serio_raw->dev);
diff --git a/drivers/isdn/gigaset/common.c b/drivers/isdn/gigaset/common.c
index 5800bee..defd5743 100644
--- a/drivers/isdn/gigaset/common.c
+++ b/drivers/isdn/gigaset/common.c
@@ -702,7 +702,7 @@
 	cs->open_count = 0;
 	cs->dev = NULL;
 	cs->tty = NULL;
-	cs->class = NULL;
+	cs->tty_dev = NULL;
 	cs->cidmode = cidmode != 0;
 
 	//if(onechannel) { //FIXME
diff --git a/drivers/isdn/gigaset/gigaset.h b/drivers/isdn/gigaset/gigaset.h
index 884bd72..06298cc 100644
--- a/drivers/isdn/gigaset/gigaset.h
+++ b/drivers/isdn/gigaset/gigaset.h
@@ -444,7 +444,7 @@
 	struct gigaset_driver *driver;
 	unsigned minor_index;
 	struct device *dev;
-	struct class_device *class;
+	struct device *tty_dev;
 
 	const struct gigaset_ops *ops;
 
diff --git a/drivers/isdn/gigaset/interface.c b/drivers/isdn/gigaset/interface.c
index 596f3ae..7edea01 100644
--- a/drivers/isdn/gigaset/interface.c
+++ b/drivers/isdn/gigaset/interface.c
@@ -625,13 +625,13 @@
 		return;
 
 	tasklet_init(&cs->if_wake_tasklet, &if_wake, (unsigned long) cs);
-	cs->class = tty_register_device(drv->tty, cs->minor_index, NULL);
+	cs->tty_dev = tty_register_device(drv->tty, cs->minor_index, NULL);
 
-	if (!IS_ERR(cs->class))
-		class_set_devdata(cs->class, cs);
+	if (!IS_ERR(cs->tty_dev))
+		dev_set_drvdata(cs->tty_dev, cs);
 	else {
 		warn("could not register device to the tty subsystem");
-		cs->class = NULL;
+		cs->tty_dev = NULL;
 	}
 }
 
@@ -645,7 +645,7 @@
 
 	tasklet_disable(&cs->if_wake_tasklet);
 	tasklet_kill(&cs->if_wake_tasklet);
-	cs->class = NULL;
+	cs->tty_dev = NULL;
 	tty_unregister_device(drv->tty, cs->minor_index);
 }
 
diff --git a/drivers/isdn/gigaset/proc.c b/drivers/isdn/gigaset/proc.c
index 9ad840e..e767afa 100644
--- a/drivers/isdn/gigaset/proc.c
+++ b/drivers/isdn/gigaset/proc.c
@@ -16,11 +16,12 @@
 #include "gigaset.h"
 #include <linux/ctype.h>
 
-static ssize_t show_cidmode(struct class_device *class, char *buf)
+static ssize_t show_cidmode(struct device *dev,
+			    struct device_attribute *attr, char *buf)
 {
 	int ret;
 	unsigned long flags;
-	struct cardstate *cs = class_get_devdata(class);
+	struct cardstate *cs = dev_get_drvdata(dev);
 
 	spin_lock_irqsave(&cs->lock, flags);
 	ret = sprintf(buf, "%u\n", cs->cidmode);
@@ -29,10 +30,10 @@
 	return ret;
 }
 
-static ssize_t set_cidmode(struct class_device *class,
+static ssize_t set_cidmode(struct device *dev, struct device_attribute *attr,
 			   const char *buf, size_t count)
 {
-	struct cardstate *cs = class_get_devdata(class);
+	struct cardstate *cs = dev_get_drvdata(dev);
 	long int value;
 	char *end;
 
@@ -64,25 +65,25 @@
 	return count;
 }
 
-static CLASS_DEVICE_ATTR(cidmode, S_IRUGO|S_IWUSR, show_cidmode, set_cidmode);
+static DEVICE_ATTR(cidmode, S_IRUGO|S_IWUSR, show_cidmode, set_cidmode);
 
 /* free sysfs for device */
 void gigaset_free_dev_sysfs(struct cardstate *cs)
 {
-	if (!cs->class)
+	if (!cs->tty_dev)
 		return;
 
 	gig_dbg(DEBUG_INIT, "removing sysfs entries");
-	class_device_remove_file(cs->class, &class_device_attr_cidmode);
+	device_remove_file(cs->tty_dev, &dev_attr_cidmode);
 }
 
 /* initialize sysfs for device */
 void gigaset_init_dev_sysfs(struct cardstate *cs)
 {
-	if (!cs->class)
+	if (!cs->tty_dev)
 		return;
 
 	gig_dbg(DEBUG_INIT, "setting up sysfs");
-	if (class_device_create_file(cs->class, &class_device_attr_cidmode))
+	if (device_create_file(cs->tty_dev, &dev_attr_cidmode))
 		dev_err(cs->dev, "could not create sysfs attribute\n");
 }
diff --git a/drivers/isdn/gigaset/usb-gigaset.c b/drivers/isdn/gigaset/usb-gigaset.c
index 4ffa9eb..5ebf49ac9 100644
--- a/drivers/isdn/gigaset/usb-gigaset.c
+++ b/drivers/isdn/gigaset/usb-gigaset.c
@@ -815,14 +815,11 @@
 	return 0;
 
 error:
-	if (ucs->read_urb)
-		usb_kill_urb(ucs->read_urb);
+	usb_kill_urb(ucs->read_urb);
 	kfree(ucs->bulk_out_buffer);
-	if (ucs->bulk_out_urb != NULL)
-		usb_free_urb(ucs->bulk_out_urb);
+	usb_free_urb(ucs->bulk_out_urb);
 	kfree(cs->inbuf[0].rcvbuf);
-	if (ucs->read_urb != NULL)
-		usb_free_urb(ucs->read_urb);
+	usb_free_urb(ucs->read_urb);
 	usb_set_intfdata(interface, NULL);
 	ucs->read_urb = ucs->bulk_out_urb = NULL;
 	cs->inbuf[0].rcvbuf = ucs->bulk_out_buffer = NULL;
@@ -850,11 +847,9 @@
 	usb_kill_urb(ucs->bulk_out_urb);	/* FIXME: only if active? */
 
 	kfree(ucs->bulk_out_buffer);
-	if (ucs->bulk_out_urb != NULL)
-		usb_free_urb(ucs->bulk_out_urb);
+	usb_free_urb(ucs->bulk_out_urb);
 	kfree(cs->inbuf[0].rcvbuf);
-	if (ucs->read_urb != NULL)
-		usb_free_urb(ucs->read_urb);
+	usb_free_urb(ucs->read_urb);
 	ucs->read_urb = ucs->bulk_out_urb = NULL;
 	cs->inbuf[0].rcvbuf = ucs->bulk_out_buffer = NULL;
 
diff --git a/drivers/isdn/hardware/eicon/os_4bri.c b/drivers/isdn/hardware/eicon/os_4bri.c
index 11e6f93..7b4ec3f 100644
--- a/drivers/isdn/hardware/eicon/os_4bri.c
+++ b/drivers/isdn/hardware/eicon/os_4bri.c
@@ -464,7 +464,7 @@
 
 /*
 **  Cleanup function will be called for master adapter only
-**  this is garanteed by design: cleanup callback is set
+**  this is guaranteed by design: cleanup callback is set
 **  by master adapter only
 */
 static int diva_4bri_cleanup_adapter(diva_os_xdi_adapter_t * a)
diff --git a/drivers/isdn/hisax/hfc4s8s_l1.h b/drivers/isdn/hisax/hfc4s8s_l1.h
index e8f9c07..9d5d2a5 100644
--- a/drivers/isdn/hisax/hfc4s8s_l1.h
+++ b/drivers/isdn/hisax/hfc4s8s_l1.h
@@ -16,7 +16,7 @@
 
 /*
 *  include Genero generated HFC-4S/8S header file hfc48scu.h
-*  for comlete register description. This will define _HFC48SCU_H_
+*  for complete register description. This will define _HFC48SCU_H_
 *  to prevent redefinitions
 */
 
diff --git a/drivers/isdn/hisax/isdnl2.c b/drivers/isdn/hisax/isdnl2.c
index 6d04317..cd3b5ad 100644
--- a/drivers/isdn/hisax/isdnl2.c
+++ b/drivers/isdn/hisax/isdnl2.c
@@ -1442,7 +1442,7 @@
 }
 
 static void
-l2_st14_persistant_da(struct FsmInst *fi, int event, void *arg)
+l2_st14_persistent_da(struct FsmInst *fi, int event, void *arg)
 {
 	struct PStack *st = fi->userdata;
 	
@@ -1453,7 +1453,7 @@
 }
 
 static void
-l2_st5_persistant_da(struct FsmInst *fi, int event, void *arg)
+l2_st5_persistent_da(struct FsmInst *fi, int event, void *arg)
 {
 	struct PStack *st = fi->userdata;
 
@@ -1466,7 +1466,7 @@
 }
 
 static void
-l2_st6_persistant_da(struct FsmInst *fi, int event, void *arg)
+l2_st6_persistent_da(struct FsmInst *fi, int event, void *arg)
 {
 	struct PStack *st = fi->userdata;
 
@@ -1477,7 +1477,7 @@
 }
 
 static void
-l2_persistant_da(struct FsmInst *fi, int event, void *arg)
+l2_persistent_da(struct FsmInst *fi, int event, void *arg)
 {
 	struct PStack *st = fi->userdata;
 
@@ -1612,14 +1612,14 @@
 	{ST_L2_6, EV_L2_FRAME_ERROR, l2_frame_error},
 	{ST_L2_7, EV_L2_FRAME_ERROR, l2_frame_error_reest},
 	{ST_L2_8, EV_L2_FRAME_ERROR, l2_frame_error_reest},
-	{ST_L2_1, EV_L1_DEACTIVATE, l2_st14_persistant_da},
+	{ST_L2_1, EV_L1_DEACTIVATE, l2_st14_persistent_da},
 	{ST_L2_2, EV_L1_DEACTIVATE, l2_st24_tei_remove},
 	{ST_L2_3, EV_L1_DEACTIVATE, l2_st3_tei_remove},
-	{ST_L2_4, EV_L1_DEACTIVATE, l2_st14_persistant_da},
-	{ST_L2_5, EV_L1_DEACTIVATE, l2_st5_persistant_da},
-	{ST_L2_6, EV_L1_DEACTIVATE, l2_st6_persistant_da},
-	{ST_L2_7, EV_L1_DEACTIVATE, l2_persistant_da},
-	{ST_L2_8, EV_L1_DEACTIVATE, l2_persistant_da},
+	{ST_L2_4, EV_L1_DEACTIVATE, l2_st14_persistent_da},
+	{ST_L2_5, EV_L1_DEACTIVATE, l2_st5_persistent_da},
+	{ST_L2_6, EV_L1_DEACTIVATE, l2_st6_persistent_da},
+	{ST_L2_7, EV_L1_DEACTIVATE, l2_persistent_da},
+	{ST_L2_8, EV_L1_DEACTIVATE, l2_persistent_da},
 };
 
 #define L2_FN_COUNT (sizeof(L2FnList)/sizeof(struct FsmNode))
diff --git a/drivers/media/dvb/cinergyT2/cinergyT2.c b/drivers/media/dvb/cinergyT2/cinergyT2.c
index ff7d4f5..55bc891 100644
--- a/drivers/media/dvb/cinergyT2/cinergyT2.c
+++ b/drivers/media/dvb/cinergyT2/cinergyT2.c
@@ -275,8 +275,7 @@
 	int i;
 
 	for (i=0; i<STREAM_URB_COUNT; i++)
-		if (cinergyt2->stream_urb[i])
-			usb_free_urb(cinergyt2->stream_urb[i]);
+		usb_free_urb(cinergyt2->stream_urb[i]);
 
 	usb_buffer_free(cinergyt2->udev, STREAM_URB_COUNT*STREAM_BUF_SIZE,
 			    cinergyt2->streambuf, cinergyt2->streambuf_dmahandle);
@@ -320,8 +319,7 @@
 	cinergyt2_control_stream_transfer(cinergyt2, 0);
 
 	for (i=0; i<STREAM_URB_COUNT; i++)
-		if (cinergyt2->stream_urb[i])
-			usb_kill_urb(cinergyt2->stream_urb[i]);
+		usb_kill_urb(cinergyt2->stream_urb[i]);
 }
 
 static int cinergyt2_start_stream_xfer (struct cinergyt2 *cinergyt2)
diff --git a/drivers/media/dvb/ttpci/budget-patch.c b/drivers/media/dvb/ttpci/budget-patch.c
index fc1267b..9a15539 100644
--- a/drivers/media/dvb/ttpci/budget-patch.c
+++ b/drivers/media/dvb/ttpci/budget-patch.c
@@ -500,14 +500,14 @@
 
 /*      New design (By Emard)
 **      this rps1 code will copy internal HS event to GPIO3 pin.
-**      GPIO3 is in budget-patch hardware connectd to port B VSYNC
+**      GPIO3 is in budget-patch hardware connected to port B VSYNC
 
 **      HS is an internal event of 7146, accessible with RPS
 **      and temporarily raised high every n lines
 **      (n in defined in the RPS_THRESH1 counter threshold)
 **      I think HS is raised high on the beginning of the n-th line
 **      and remains high until this n-th line that triggered
-**      it is completely received. When the receiption of n-th line
+**      it is completely received. When the reception of n-th line
 **      ends, HS is lowered.
 
 **      To transmit data over DMA, 7146 needs changing state at
@@ -541,7 +541,7 @@
 **      hardware debug note: a working budget card (including budget patch)
 **      with vpeirq() interrupt setup in mode "0x90" (every 64K) will
 **      generate 3 interrupts per 25-Hz DMA frame of 2*188*512 bytes
-**      and that means 3*25=75 Hz of interrupt freqency, as seen by
+**      and that means 3*25=75 Hz of interrupt frequency, as seen by
 **      watch cat /proc/interrupts
 **
 **      If this frequency is 3x lower (and data received in the DMA
@@ -550,7 +550,7 @@
 **      this means VSYNC line is not connected in the hardware.
 **      (check soldering pcb and pins)
 **      The same behaviour of missing VSYNC can be duplicated on budget
-**      cards, by seting DD1_INIT trigger mode 7 in 3rd nibble.
+**      cards, by setting DD1_INIT trigger mode 7 in 3rd nibble.
 */
 
 	// Setup RPS1 "program" (p35)
diff --git a/drivers/media/dvb/ttusb-dec/ttusb_dec.c b/drivers/media/dvb/ttusb-dec/ttusb_dec.c
index a1c9fa9..8135f3e 100644
--- a/drivers/media/dvb/ttusb-dec/ttusb_dec.c
+++ b/drivers/media/dvb/ttusb-dec/ttusb_dec.c
@@ -1135,8 +1135,7 @@
 	dprintk("%s\n", __FUNCTION__);
 
 	for (i = 0; i < ISO_BUF_COUNT; i++)
-		if (dec->iso_urb[i])
-			usb_free_urb(dec->iso_urb[i]);
+		usb_free_urb(dec->iso_urb[i]);
 
 	pci_free_consistent(NULL,
 			    ISO_FRAME_SIZE * (FRAMES_PER_ISO_BUF *
diff --git a/drivers/media/video/Kconfig b/drivers/media/video/Kconfig
index bf26755..b8fde5c 100644
--- a/drivers/media/video/Kconfig
+++ b/drivers/media/video/Kconfig
@@ -24,7 +24,7 @@
 	  decode audio/video standards. This option will autoselect
 	  all pertinent modules to each selected video module.
 
-	  Unselect this only if you know exaclty what you are doing, since
+	  Unselect this only if you know exactly what you are doing, since
 	  it may break support on some boards.
 
 	  In doubt, say Y.
diff --git a/drivers/media/video/pvrusb2/pvrusb2-hdw.c b/drivers/media/video/pvrusb2/pvrusb2-hdw.c
index f920e0c..1f78733 100644
--- a/drivers/media/video/pvrusb2/pvrusb2-hdw.c
+++ b/drivers/media/video/pvrusb2/pvrusb2-hdw.c
@@ -1953,8 +1953,8 @@
 	return hdw;
  fail:
 	if (hdw) {
-		if (hdw->ctl_read_urb) usb_free_urb(hdw->ctl_read_urb);
-		if (hdw->ctl_write_urb) usb_free_urb(hdw->ctl_write_urb);
+		usb_free_urb(hdw->ctl_read_urb);
+		usb_free_urb(hdw->ctl_write_urb);
 		if (hdw->ctl_read_buffer) kfree(hdw->ctl_read_buffer);
 		if (hdw->ctl_write_buffer) kfree(hdw->ctl_write_buffer);
 		if (hdw->controls) kfree(hdw->controls);
@@ -2575,12 +2575,10 @@
 	struct pvr2_hdw *hdw = (struct pvr2_hdw *)data;
 	if (hdw->ctl_write_pend_flag || hdw->ctl_read_pend_flag) {
 		hdw->ctl_timeout_flag = !0;
-		if (hdw->ctl_write_pend_flag && hdw->ctl_write_urb) {
+		if (hdw->ctl_write_pend_flag)
 			usb_unlink_urb(hdw->ctl_write_urb);
-		}
-		if (hdw->ctl_read_pend_flag && hdw->ctl_read_urb) {
+		if (hdw->ctl_read_pend_flag)
 			usb_unlink_urb(hdw->ctl_read_urb);
-		}
 	}
 }
 
diff --git a/drivers/media/video/pvrusb2/pvrusb2-io.c b/drivers/media/video/pvrusb2/pvrusb2-io.c
index 70aa63e..57fb320 100644
--- a/drivers/media/video/pvrusb2/pvrusb2-io.c
+++ b/drivers/media/video/pvrusb2/pvrusb2-io.c
@@ -289,7 +289,7 @@
 	pvr2_buffer_set_none(bp);
 	bp->signature = 0;
 	bp->stream = NULL;
-	if (bp->purb) usb_free_urb(bp->purb);
+	usb_free_urb(bp->purb);
 	pvr2_trace(PVR2_TRACE_BUF_POOL,"/*---TRACE_FLOW---*/"
 		   " bufferDone     %p",bp);
 }
diff --git a/drivers/media/video/pwc/pwc-if.c b/drivers/media/video/pwc/pwc-if.c
index 46c1148..a996aad 100644
--- a/drivers/media/video/pwc/pwc-if.c
+++ b/drivers/media/video/pwc/pwc-if.c
@@ -866,11 +866,9 @@
 	}
 	if (ret) {
 		/* De-allocate in reverse order */
-		while (i >= 0) {
-			if (pdev->sbuf[i].urb != NULL)
-				usb_free_urb(pdev->sbuf[i].urb);
+		while (i--) {
+			usb_free_urb(pdev->sbuf[i].urb);
 			pdev->sbuf[i].urb = NULL;
-			i--;
 		}
 		return ret;
 	}
@@ -1095,8 +1093,7 @@
 	PWC_DEBUG_OPEN(">> video_open called(vdev = 0x%p).\n", vdev);
 
 	pdev = (struct pwc_device *)vdev->priv;
-	if (pdev == NULL)
-		BUG();
+	BUG_ON(!pdev);
 	if (pdev->vopen) {
 		PWC_DEBUG_OPEN("I'm busy, someone is using the device.\n");
 		return -EBUSY;
diff --git a/drivers/media/video/sn9c102/sn9c102_core.c b/drivers/media/video/sn9c102/sn9c102_core.c
index 42fb60d..18458d4 100644
--- a/drivers/media/video/sn9c102/sn9c102_core.c
+++ b/drivers/media/video/sn9c102/sn9c102_core.c
@@ -775,7 +775,7 @@
 	return 0;
 
 free_urbs:
-	for (i = 0; (i < SN9C102_URBS) &&  cam->urb[i]; i++)
+	for (i = 0; i < SN9C102_URBS; i++)
 		usb_free_urb(cam->urb[i]);
 
 free_buffers:
diff --git a/drivers/media/video/usbvideo/quickcam_messenger.c b/drivers/media/video/usbvideo/quickcam_messenger.c
index 9a26b94..bbf2bee 100644
--- a/drivers/media/video/usbvideo/quickcam_messenger.c
+++ b/drivers/media/video/usbvideo/quickcam_messenger.c
@@ -190,8 +190,7 @@
 
 static void qcm_free_int(struct qcm *cam)
 {
-	if (cam->button_urb)
-		usb_free_urb(cam->button_urb);
+	usb_free_urb(cam->button_urb);
 }
 #endif /* CONFIG_INPUT */
 
diff --git a/drivers/media/video/zc0301/zc0301_core.c b/drivers/media/video/zc0301/zc0301_core.c
index 5b55634..52d0f75 100644
--- a/drivers/media/video/zc0301/zc0301_core.c
+++ b/drivers/media/video/zc0301/zc0301_core.c
@@ -489,7 +489,7 @@
 	return 0;
 
 free_urbs:
-	for (i = 0; (i < ZC0301_URBS) &&  cam->urb[i]; i++)
+	for (i = 0; i < ZC0301_URBS; i++)
 		usb_free_urb(cam->urb[i]);
 
 free_buffers:
diff --git a/drivers/message/fusion/mptbase.c b/drivers/message/fusion/mptbase.c
index e5c7271..051b7c5 100644
--- a/drivers/message/fusion/mptbase.c
+++ b/drivers/message/fusion/mptbase.c
@@ -6185,7 +6185,7 @@
 		"Abort",					/* 12h */
 		"IO Not Yet Executed",				/* 13h */
 		"IO Executed",					/* 14h */
-		"Persistant Reservation Out Not Affiliation Owner", /* 15h */
+		"Persistent Reservation Out Not Affiliation Owner", /* 15h */
 		"Open Transmit DMA Abort",			/* 16h */
 		"IO Device Missing Delay Retry",		/* 17h */
 		NULL,						/* 18h */
diff --git a/drivers/message/i2o/pci.c b/drivers/message/i2o/pci.c
index 62f1ac0..8287f95 100644
--- a/drivers/message/i2o/pci.c
+++ b/drivers/message/i2o/pci.c
@@ -320,7 +320,6 @@
 	struct i2o_controller *c;
 	int rc;
 	struct pci_dev *i960 = NULL;
-	int enabled = pdev->is_enabled;
 
 	printk(KERN_INFO "i2o: Checking for PCI I2O controllers...\n");
 
@@ -330,12 +329,11 @@
 		return -ENODEV;
 	}
 
-	if (!enabled)
-		if ((rc = pci_enable_device(pdev))) {
-			printk(KERN_WARNING "i2o: couldn't enable device %s\n",
-			       pci_name(pdev));
-			return rc;
-		}
+	if ((rc = pci_enable_device(pdev))) {
+		printk(KERN_WARNING "i2o: couldn't enable device %s\n",
+		       pci_name(pdev));
+		return rc;
+	}
 
 	if (pci_set_dma_mask(pdev, DMA_32BIT_MASK)) {
 		printk(KERN_WARNING "i2o: no suitable DMA found for %s\n",
@@ -442,8 +440,7 @@
 	i2o_iop_free(c);
 
       disable:
-	if (!enabled)
-		pci_disable_device(pdev);
+	pci_disable_device(pdev);
 
 	return rc;
 }
diff --git a/drivers/mmc/mmc_queue.c b/drivers/mmc/mmc_queue.c
index 4ccdd82..61a1de8 100644
--- a/drivers/mmc/mmc_queue.c
+++ b/drivers/mmc/mmc_queue.c
@@ -130,8 +130,8 @@
 	u64 limit = BLK_BOUNCE_HIGH;
 	int ret;
 
-	if (host->dev->dma_mask && *host->dev->dma_mask)
-		limit = *host->dev->dma_mask;
+	if (mmc_dev(host)->dma_mask && *mmc_dev(host)->dma_mask)
+		limit = *mmc_dev(host)->dma_mask;
 
 	mq->card = card;
 	mq->queue = blk_init_queue(mmc_request, lock);
diff --git a/drivers/mmc/mmc_sysfs.c b/drivers/mmc/mmc_sysfs.c
index 10cc973..ac53296 100644
--- a/drivers/mmc/mmc_sysfs.c
+++ b/drivers/mmc/mmc_sysfs.c
@@ -199,7 +199,7 @@
 	memset(card, 0, sizeof(struct mmc_card));
 	card->host = host;
 	device_initialize(&card->dev);
-	card->dev.parent = card->host->dev;
+	card->dev.parent = mmc_dev(host);
 	card->dev.bus = &mmc_bus_type;
 	card->dev.release = mmc_release_card;
 }
@@ -242,7 +242,7 @@
 }
 
 
-static void mmc_host_classdev_release(struct class_device *dev)
+static void mmc_host_classdev_release(struct device *dev)
 {
 	struct mmc_host *host = cls_dev_to_mmc_host(dev);
 	kfree(host);
@@ -250,7 +250,7 @@
 
 static struct class mmc_host_class = {
 	.name		= "mmc_host",
-	.release	= mmc_host_classdev_release,
+	.dev_release	= mmc_host_classdev_release,
 };
 
 static DEFINE_IDR(mmc_host_idr);
@@ -267,10 +267,10 @@
 	if (host) {
 		memset(host, 0, sizeof(struct mmc_host) + extra);
 
-		host->dev = dev;
-		host->class_dev.dev = host->dev;
+		host->parent = dev;
+		host->class_dev.parent = dev;
 		host->class_dev.class = &mmc_host_class;
-		class_device_initialize(&host->class_dev);
+		device_initialize(&host->class_dev);
 	}
 
 	return host;
@@ -292,10 +292,10 @@
 	if (err)
 		return err;
 
-	snprintf(host->class_dev.class_id, BUS_ID_SIZE,
+	snprintf(host->class_dev.bus_id, BUS_ID_SIZE,
 		 "mmc%d", host->index);
 
-	return class_device_add(&host->class_dev);
+	return device_add(&host->class_dev);
 }
 
 /*
@@ -303,7 +303,7 @@
  */
 void mmc_remove_host_sysfs(struct mmc_host *host)
 {
-	class_device_del(&host->class_dev);
+	device_del(&host->class_dev);
 
 	spin_lock(&mmc_host_lock);
 	idr_remove(&mmc_host_idr, host->index);
@@ -315,7 +315,7 @@
  */
 void mmc_free_host_sysfs(struct mmc_host *host)
 {
-	class_device_put(&host->class_dev);
+	put_device(&host->class_dev);
 }
 
 static struct workqueue_struct *workqueue;
diff --git a/drivers/mmc/omap.c b/drivers/mmc/omap.c
index 762fa28..d593ef3 100644
--- a/drivers/mmc/omap.c
+++ b/drivers/mmc/omap.c
@@ -640,8 +640,7 @@
 	}
 
 	/* Max limit for DMA frame count is 0xffff */
-	if (unlikely(count > 0xffff))
-		BUG();
+	BUG_ON(count > 0xffff);
 
 	OMAP_MMC_WRITE(host->base, BUF, buf);
 	omap_set_dma_transfer_params(dma_ch, OMAP_DMA_DATA_TYPE_S16,
diff --git a/drivers/mmc/wbsd.c b/drivers/mmc/wbsd.c
index ced309b..682e62b 100644
--- a/drivers/mmc/wbsd.c
+++ b/drivers/mmc/wbsd.c
@@ -1488,7 +1488,7 @@
 	/*
 	 * Translate the address to a physical address.
 	 */
-	host->dma_addr = dma_map_single(host->mmc->dev, host->dma_buffer,
+	host->dma_addr = dma_map_single(mmc_dev(host->mmc), host->dma_buffer,
 		WBSD_DMA_SIZE, DMA_BIDIRECTIONAL);
 
 	/*
@@ -1512,7 +1512,7 @@
 	 */
 	BUG_ON(1);
 
-	dma_unmap_single(host->mmc->dev, host->dma_addr,
+	dma_unmap_single(mmc_dev(host->mmc), host->dma_addr,
 		WBSD_DMA_SIZE, DMA_BIDIRECTIONAL);
 	host->dma_addr = (dma_addr_t)NULL;
 
@@ -1530,7 +1530,7 @@
 static void __devexit wbsd_release_dma(struct wbsd_host *host)
 {
 	if (host->dma_addr) {
-		dma_unmap_single(host->mmc->dev, host->dma_addr,
+		dma_unmap_single(mmc_dev(host->mmc), host->dma_addr,
 			WBSD_DMA_SIZE, DMA_BIDIRECTIONAL);
 	}
 	kfree(host->dma_buffer);
diff --git a/drivers/mtd/maps/Kconfig b/drivers/mtd/maps/Kconfig
index 24747bd..d132ed5 100644
--- a/drivers/mtd/maps/Kconfig
+++ b/drivers/mtd/maps/Kconfig
@@ -607,7 +607,7 @@
 	default "4"
 
 config MTD_SHARP_SL
-	bool "ROM maped on Sharp SL Series"
+	bool "ROM mapped on Sharp SL Series"
 	depends on MTD && ARCH_PXA
 	help
 	  This enables access to the flash chip on the Sharp SL Series of PDAs.
diff --git a/drivers/mtd/maps/cfi_flagadm.c b/drivers/mtd/maps/cfi_flagadm.c
index 92b5d88..65e5ee5 100644
--- a/drivers/mtd/maps/cfi_flagadm.c
+++ b/drivers/mtd/maps/cfi_flagadm.c
@@ -80,7 +80,7 @@
 		.size =		FLASH_PARTITION2_SIZE
 	},
 	{
-		.name =		"Persistant storage",
+		.name =		"Persistent storage",
 		.offset =	FLASH_PARTITION3_ADDR,
 		.size =		FLASH_PARTITION3_SIZE
 	}
diff --git a/drivers/net/Kconfig b/drivers/net/Kconfig
index 6e863aa..b6c70c5 100644
--- a/drivers/net/Kconfig
+++ b/drivers/net/Kconfig
@@ -32,7 +32,7 @@
 	tristate "Intermediate Functional Block support"
 	depends on NET_CLS_ACT
 	---help---
-	  This is an intermidiate driver that allows sharing of
+	  This is an intermediate driver that allows sharing of
 	  resources.
 	  To compile this driver as a module, choose M here: the module
 	  will be called ifb.  If you want to use more than one ifb
@@ -2136,7 +2136,7 @@
 	  This driver supports the original Yukon chipset. A cleaner driver is 
 	  also available (skge) which seems to work better than this one.
 
-	  This driver does not support the newer Yukon2 chipset. A seperate
+	  This driver does not support the newer Yukon2 chipset. A separate
 	  driver, sky2, is provided to support Yukon2-based adapters.
 
 	  The following adapters are supported by this driver:
diff --git a/drivers/net/e100.c b/drivers/net/e100.c
index 19ab344..3a8df47 100644
--- a/drivers/net/e100.c
+++ b/drivers/net/e100.c
@@ -1215,7 +1215,7 @@
 *  the literal in the instruction before the code is loaded, the
 *  driver can change the algorithm.
 *
-*  INTDELAY - This loads the dead-man timer with its inital value.
+*  INTDELAY - This loads the dead-man timer with its initial value.
 *    When this timer expires the interrupt is asserted, and the
 *    timer is reset each time a new packet is received.  (see
 *    BUNDLEMAX below to set the limit on number of chained packets)
diff --git a/drivers/net/e1000/e1000_hw.c b/drivers/net/e1000/e1000_hw.c
index 65077f3..796c4f7d 100644
--- a/drivers/net/e1000/e1000_hw.c
+++ b/drivers/net/e1000/e1000_hw.c
@@ -3868,7 +3868,7 @@
 *
 * hw - Struct containing variables accessed by shared code
 *
-* Sets bit 15 of the MII Control regiser
+* Sets bit 15 of the MII Control register
 ******************************************************************************/
 int32_t
 e1000_phy_reset(struct e1000_hw *hw)
diff --git a/drivers/net/irda/irda-usb.c b/drivers/net/irda/irda-usb.c
index 14bda76..6e95645 100644
--- a/drivers/net/irda/irda-usb.c
+++ b/drivers/net/irda/irda-usb.c
@@ -1793,10 +1793,8 @@
 err_out_2:
 	usb_free_urb(self->tx_urb);
 err_out_1:
-	for (i = 0; i < self->max_rx_urb; i++) {
-		if (self->rx_urb[i])
-			usb_free_urb(self->rx_urb[i]);
-	}
+	for (i = 0; i < self->max_rx_urb; i++)
+		usb_free_urb(self->rx_urb[i]);
 	free_netdev(net);
 err_out:
 	return ret;
diff --git a/drivers/net/phy/Kconfig b/drivers/net/phy/Kconfig
index b79ec0d..ecb61f8 100644
--- a/drivers/net/phy/Kconfig
+++ b/drivers/net/phy/Kconfig
@@ -61,8 +61,8 @@
 	depends on PHYLIB
 	---help---
 	  Adds the driver to PHY layer to cover the boards that do not have any PHY bound,
-	  but with the ability to manipulate with speed/link in software. The relavant MII
-	  speed/duplex parameters could be effectively handled in user-specified  fuction.
+	  but with the ability to manipulate the speed/link in software. The relevant MII
+	  speed/duplex parameters could be effectively handled in a user-specified function.
 	  Currently tested with mpc866ads.
 
 config FIXED_MII_10_FDX
diff --git a/drivers/net/ppp_generic.c b/drivers/net/ppp_generic.c
index f5802e7..c6de566 100644
--- a/drivers/net/ppp_generic.c
+++ b/drivers/net/ppp_generic.c
@@ -860,7 +860,7 @@
 			err = PTR_ERR(ppp_class);
 			goto out_chrdev;
 		}
-		class_device_create(ppp_class, NULL, MKDEV(PPP_MAJOR, 0), NULL, "ppp");
+		device_create(ppp_class, NULL, MKDEV(PPP_MAJOR, 0), "ppp");
 	}
 
 out:
@@ -2675,7 +2675,7 @@
 	cardmap_destroy(&all_ppp_units);
 	if (unregister_chrdev(PPP_MAJOR, "ppp") != 0)
 		printk(KERN_ERR "PPP: failed to unregister PPP device\n");
-	class_device_destroy(ppp_class, MKDEV(PPP_MAJOR, 0));
+	device_destroy(ppp_class, MKDEV(PPP_MAJOR, 0));
 	class_destroy(ppp_class);
 }
 
diff --git a/drivers/net/sk98lin/h/skdrv2nd.h b/drivers/net/sk98lin/h/skdrv2nd.h
index 778d9e6..3fa6717 100644
--- a/drivers/net/sk98lin/h/skdrv2nd.h
+++ b/drivers/net/sk98lin/h/skdrv2nd.h
@@ -160,7 +160,7 @@
 
 /*
 ** Interim definition of SK_DRV_TIMER placed in this file until 
-** common modules have boon finallized
+** common modules have been finalized
 */
 #define SK_DRV_TIMER			11 
 #define	SK_DRV_MODERATION_TIMER		1
diff --git a/drivers/net/sk98lin/skdim.c b/drivers/net/sk98lin/skdim.c
index 07c1b4c..37ce03f 100644
--- a/drivers/net/sk98lin/skdim.c
+++ b/drivers/net/sk98lin/skdim.c
@@ -252,7 +252,7 @@
 
 /*******************************************************************************
 ** Function     : SkDimDisplayModerationSettings
-** Description  : Displays the current settings regaring interrupt moderation
+** Description  : Displays the current settings regarding interrupt moderation
 ** Programmer   : Ralph Roesler
 ** Last Modified: 22-mar-03
 ** Returns      : void (!)
@@ -510,7 +510,7 @@
 
 /*******************************************************************************
 ** Function     : DisableIntMod()
-** Description  : Disbles the interrupt moderation independent of what inter-
+** Description  : Disables the interrupt moderation independent of what inter-
 **                rupts are running or not
 ** Programmer   : Ralph Roesler
 ** Last Modified: 23-mar-03
diff --git a/drivers/net/wireless/ipw2200.c b/drivers/net/wireless/ipw2200.c
index 1f74281..72120d5 100644
--- a/drivers/net/wireless/ipw2200.c
+++ b/drivers/net/wireless/ipw2200.c
@@ -6920,8 +6920,8 @@
 }
 
 /*
-* handling the beaconing responces. if we get different QoS setting
-* of the network from the the associated setting adjust the QoS
+* handling the beaconing responses. if we get different QoS setting
+* off the network from the associated setting, adjust the QoS
 * setting
 */
 static int ipw_qos_association_resp(struct ipw_priv *priv,
diff --git a/drivers/net/wireless/zd1201.c b/drivers/net/wireless/zd1201.c
index 36b29ff..6cb66a3 100644
--- a/drivers/net/wireless/zd1201.c
+++ b/drivers/net/wireless/zd1201.c
@@ -1828,10 +1828,8 @@
 	/* Leave the device in reset state */
 	zd1201_docmd(zd, ZD1201_CMDCODE_INIT, 0, 0, 0);
 err_zd:
-	if (zd->tx_urb)
-		usb_free_urb(zd->tx_urb);
-	if (zd->rx_urb)
-		usb_free_urb(zd->rx_urb);
+	usb_free_urb(zd->tx_urb);
+	usb_free_urb(zd->rx_urb);
 	kfree(zd);
 	return err;
 }
diff --git a/drivers/parisc/ccio-dma.c b/drivers/parisc/ccio-dma.c
index 68cb3a0..fe3f5f5 100644
--- a/drivers/parisc/ccio-dma.c
+++ b/drivers/parisc/ccio-dma.c
@@ -486,7 +486,7 @@
 **   This bit tells U2 to do R/M/W for partial cachelines. "Streaming"
 **   data can avoid this if the mapping covers full cache lines.
 ** o STOP_MOST is needed for atomicity across cachelines.
-**   Apperently only "some EISA devices" need this.
+**   Apparently only "some EISA devices" need this.
 **   Using CONFIG_ISA is hack. Only the IOA with EISA under it needs
 **   to use this hint iff the EISA devices needs this feature.
 **   According to the U2 ERS, STOP_MOST enabled pages hurt performance.
diff --git a/drivers/parisc/iosapic.c b/drivers/parisc/iosapic.c
index c2949b4..12bab64 100644
--- a/drivers/parisc/iosapic.c
+++ b/drivers/parisc/iosapic.c
@@ -50,12 +50,12 @@
 **
 ** PA Firmware
 ** -----------
-** PA-RISC platforms have two fundementally different types of firmware.
+** PA-RISC platforms have two fundamentally different types of firmware.
 ** For PCI devices, "Legacy" PDC initializes the "INTERRUPT_LINE" register
 ** and BARs similar to a traditional PC BIOS.
 ** The newer "PAT" firmware supports PDC calls which return tables.
-** PAT firmware only initializes PCI Console and Boot interface.
-** With these tables, the OS can progam all other PCI devices.
+** PAT firmware only initializes the PCI Console and Boot interface.
+** With these tables, the OS can program all other PCI devices.
 **
 ** One such PAT PDC call returns the "Interrupt Routing Table" (IRT).
 ** The IRT maps each PCI slot's INTA-D "output" line to an I/O SAPIC
diff --git a/drivers/pci/Kconfig b/drivers/pci/Kconfig
index 5f1b9f5..f1dd81a 100644
--- a/drivers/pci/Kconfig
+++ b/drivers/pci/Kconfig
@@ -19,7 +19,7 @@
 
 config PCI_MULTITHREAD_PROBE
 	bool "PCI Multi-threaded probe (EXPERIMENTAL)"
-	depends on PCI && EXPERIMENTAL && BROKEN
+	depends on PCI && EXPERIMENTAL
 	help
 	  Say Y here if you want the PCI core to spawn a new thread for
 	  every PCI device that is probed.  This can cause a huge
@@ -27,14 +27,14 @@
 	  smaller speedup on single processor machines.
 
 	  But it can also cause lots of bad things to happen.  A number
-	  of PCI drivers can not properly handle running in this way,
+	  of PCI drivers cannot properly handle running in this way,
 	  some will just not work properly at all, while others might
 	  decide to blow up power supplies with a huge load all at once,
 	  so use this option at your own risk.
 
 	  It is very unwise to use this option if you are not using a
 	  boot process that can handle devices being created in any
-	  order.  A program that can create persistant block and network
+	  order.  A program that can create persistent block and network
 	  device names (like udev) is a good idea if you wish to use
 	  this option.
 
diff --git a/drivers/pci/access.c b/drivers/pci/access.c
index ea16805..73a58c7 100644
--- a/drivers/pci/access.c
+++ b/drivers/pci/access.c
@@ -1,6 +1,7 @@
 #include <linux/pci.h>
 #include <linux/module.h>
 #include <linux/ioport.h>
+#include <linux/wait.h>
 
 #include "pci.h"
 
@@ -63,30 +64,42 @@
 EXPORT_SYMBOL(pci_bus_write_config_word);
 EXPORT_SYMBOL(pci_bus_write_config_dword);
 
-static u32 pci_user_cached_config(struct pci_dev *dev, int pos)
-{
-	u32 data;
+/*
+ * The following routines are to prevent the user from accessing PCI config
+ * space when it's unsafe to do so.  Some devices require this during BIST and
+ * we're required to prevent it during D-state transitions.
+ *
+ * We have a bit per device to indicate it's blocked and a global wait queue
+ * for callers to sleep on until devices are unblocked.
+ */
+static DECLARE_WAIT_QUEUE_HEAD(pci_ucfg_wait);
 
-	data = dev->saved_config_space[pos/sizeof(dev->saved_config_space[0])];
-	data >>= (pos % sizeof(dev->saved_config_space[0])) * 8;
-	return data;
+static noinline void pci_wait_ucfg(struct pci_dev *dev)
+{
+	DECLARE_WAITQUEUE(wait, current);
+
+	__add_wait_queue(&pci_ucfg_wait, &wait);
+	do {
+		set_current_state(TASK_UNINTERRUPTIBLE);
+		spin_unlock_irq(&pci_lock);
+		schedule();
+		spin_lock_irq(&pci_lock);
+	} while (dev->block_ucfg_access);
+	__remove_wait_queue(&pci_ucfg_wait, &wait);
 }
 
 #define PCI_USER_READ_CONFIG(size,type)					\
 int pci_user_read_config_##size						\
 	(struct pci_dev *dev, int pos, type *val)			\
 {									\
-	unsigned long flags;						\
 	int ret = 0;							\
 	u32 data = -1;							\
 	if (PCI_##size##_BAD) return PCIBIOS_BAD_REGISTER_NUMBER;	\
-	spin_lock_irqsave(&pci_lock, flags);				\
-	if (likely(!dev->block_ucfg_access))				\
-		ret = dev->bus->ops->read(dev->bus, dev->devfn,		\
+	spin_lock_irq(&pci_lock);					\
+	if (unlikely(dev->block_ucfg_access)) pci_wait_ucfg(dev);	\
+	ret = dev->bus->ops->read(dev->bus, dev->devfn,			\
 					pos, sizeof(type), &data);	\
-	else if (pos < sizeof(dev->saved_config_space))			\
-		data = pci_user_cached_config(dev, pos); 		\
-	spin_unlock_irqrestore(&pci_lock, flags);			\
+	spin_unlock_irq(&pci_lock);					\
 	*val = (type)data;						\
 	return ret;							\
 }
@@ -95,14 +108,13 @@
 int pci_user_write_config_##size					\
 	(struct pci_dev *dev, int pos, type val)			\
 {									\
-	unsigned long flags;						\
 	int ret = -EIO;							\
 	if (PCI_##size##_BAD) return PCIBIOS_BAD_REGISTER_NUMBER;	\
-	spin_lock_irqsave(&pci_lock, flags);				\
-	if (likely(!dev->block_ucfg_access))				\
-		ret = dev->bus->ops->write(dev->bus, dev->devfn,	\
+	spin_lock_irq(&pci_lock);					\
+	if (unlikely(dev->block_ucfg_access)) pci_wait_ucfg(dev);	\
+	ret = dev->bus->ops->write(dev->bus, dev->devfn,		\
 					pos, sizeof(type), val);	\
-	spin_unlock_irqrestore(&pci_lock, flags);			\
+	spin_unlock_irq(&pci_lock);					\
 	return ret;							\
 }
 
@@ -117,21 +129,23 @@
  * pci_block_user_cfg_access - Block userspace PCI config reads/writes
  * @dev:	pci device struct
  *
- * This function blocks any userspace PCI config accesses from occurring.
- * When blocked, any writes will be bit bucketed and reads will return the
- * data saved using pci_save_state for the first 64 bytes of config
- * space and return 0xff for all other config reads.
- **/
+ * When user access is blocked, any reads or writes to config space will
+ * sleep until access is unblocked again.  We don't allow nesting of
+ * block/unblock calls.
+ */
 void pci_block_user_cfg_access(struct pci_dev *dev)
 {
 	unsigned long flags;
+	int was_blocked;
 
-	pci_save_state(dev);
-
-	/* spinlock to synchronize with anyone reading config space now */
 	spin_lock_irqsave(&pci_lock, flags);
+	was_blocked = dev->block_ucfg_access;
 	dev->block_ucfg_access = 1;
 	spin_unlock_irqrestore(&pci_lock, flags);
+
+	/* If we BUG() inside the pci_lock, we're guaranteed to hose
+	 * the machine */
+	BUG_ON(was_blocked);
 }
 EXPORT_SYMBOL_GPL(pci_block_user_cfg_access);
 
@@ -140,14 +154,19 @@
  * @dev:	pci device struct
  *
  * This function allows userspace PCI config accesses to resume.
- **/
+ */
 void pci_unblock_user_cfg_access(struct pci_dev *dev)
 {
 	unsigned long flags;
 
-	/* spinlock to synchronize with anyone reading saved config space */
 	spin_lock_irqsave(&pci_lock, flags);
+
+	/* This indicates a problem in the caller, but we don't need
+	 * to kill them, unlike a double-block above. */
+	WARN_ON(!dev->block_ucfg_access);
+
 	dev->block_ucfg_access = 0;
+	wake_up_all(&pci_ucfg_wait);
 	spin_unlock_irqrestore(&pci_lock, flags);
 }
 EXPORT_SYMBOL_GPL(pci_unblock_user_cfg_access);
diff --git a/drivers/pci/hotplug/acpiphp.h b/drivers/pci/hotplug/acpiphp.h
index 59c5b24..ddbadd95 100644
--- a/drivers/pci/hotplug/acpiphp.h
+++ b/drivers/pci/hotplug/acpiphp.h
@@ -62,10 +62,10 @@
 struct slot {
 	struct hotplug_slot	*hotplug_slot;
 	struct acpiphp_slot	*acpi_slot;
+	struct hotplug_slot_info info;
+	char name[SLOT_NAME_SIZE];
 };
 
-
-
 /**
  * struct acpiphp_bridge - PCI bridge information
  *
diff --git a/drivers/pci/hotplug/acpiphp_core.c b/drivers/pci/hotplug/acpiphp_core.c
index c57d9d5..40c79b0 100644
--- a/drivers/pci/hotplug/acpiphp_core.c
+++ b/drivers/pci/hotplug/acpiphp_core.c
@@ -303,25 +303,15 @@
 	/* read initial number of slots */
 	if (!retval) {
 		num_slots = acpiphp_get_num_slots();
-		if (num_slots == 0)
+		if (num_slots == 0) {
+			acpiphp_glue_exit();
 			retval = -ENODEV;
+		}
 	}
 
 	return retval;
 }
 
-
-/**
- * make_slot_name - make a slot name that appears in pcihpfs
- * @slot: slot to name
- *
- */
-static void make_slot_name(struct slot *slot)
-{
-	snprintf(slot->hotplug_slot->name, SLOT_NAME_SIZE, "%u",
-		 slot->acpi_slot->sun);
-}
-
 /**
  * release_slot - free up the memory used by a slot
  * @hotplug_slot: slot to free
@@ -332,8 +322,6 @@
 
 	dbg("%s - physical_slot = %s\n", __FUNCTION__, hotplug_slot->name);
 
-	kfree(slot->hotplug_slot->info);
-	kfree(slot->hotplug_slot->name);
 	kfree(slot->hotplug_slot);
 	kfree(slot);
 }
@@ -342,26 +330,19 @@
 int acpiphp_register_hotplug_slot(struct acpiphp_slot *acpiphp_slot)
 {
 	struct slot *slot;
-	struct hotplug_slot *hotplug_slot;
-	struct hotplug_slot_info *hotplug_slot_info;
 	int retval = -ENOMEM;
 
 	slot = kzalloc(sizeof(*slot), GFP_KERNEL);
 	if (!slot)
 		goto error;
 
-	slot->hotplug_slot = kzalloc(sizeof(*hotplug_slot), GFP_KERNEL);
+	slot->hotplug_slot = kzalloc(sizeof(*slot->hotplug_slot), GFP_KERNEL);
 	if (!slot->hotplug_slot)
 		goto error_slot;
 
-	slot->hotplug_slot->info = kzalloc(sizeof(*hotplug_slot_info),
-					   GFP_KERNEL);
-	if (!slot->hotplug_slot->info)
-		goto error_hpslot;
+	slot->hotplug_slot->info = &slot->info;
 
-	slot->hotplug_slot->name = kzalloc(SLOT_NAME_SIZE, GFP_KERNEL);
-	if (!slot->hotplug_slot->name)
-		goto error_info;
+	slot->hotplug_slot->name = slot->name;
 
 	slot->hotplug_slot->private = slot;
 	slot->hotplug_slot->release = &release_slot;
@@ -376,21 +357,17 @@
 	slot->hotplug_slot->info->cur_bus_speed = PCI_SPEED_UNKNOWN;
 
 	acpiphp_slot->slot = slot;
-	make_slot_name(slot);
+	snprintf(slot->name, sizeof(slot->name), "%u", slot->acpi_slot->sun);
 
 	retval = pci_hp_register(slot->hotplug_slot);
 	if (retval) {
 		err("pci_hp_register failed with error %d\n", retval);
-		goto error_name;
+		goto error_hpslot;
  	}
 
 	info("Slot [%s] registered\n", slot->hotplug_slot->name);
 
 	return 0;
-error_name:
-	kfree(slot->hotplug_slot->name);
-error_info:
-	kfree(slot->hotplug_slot->info);
 error_hpslot:
 	kfree(slot->hotplug_slot);
 error_slot:
diff --git a/drivers/pci/hotplug/acpiphp_glue.c b/drivers/pci/hotplug/acpiphp_glue.c
index 16167b0..0b9d0db 100644
--- a/drivers/pci/hotplug/acpiphp_glue.c
+++ b/drivers/pci/hotplug/acpiphp_glue.c
@@ -1693,14 +1693,10 @@
  */
 int __init acpiphp_get_num_slots(void)
 {
-	struct list_head *node;
 	struct acpiphp_bridge *bridge;
-	int num_slots;
+	int num_slots = 0;
 
-	num_slots = 0;
-
-	list_for_each (node, &bridge_list) {
-		bridge = (struct acpiphp_bridge *)node;
+	list_for_each_entry (bridge, &bridge_list, list) {
 		dbg("Bus %04x:%02x has %d slot%s\n",
 				pci_domain_nr(bridge->pci_bus),
 				bridge->pci_bus->number, bridge->nr_slots,
diff --git a/drivers/pci/hotplug/ibmphp_hpc.c b/drivers/pci/hotplug/ibmphp_hpc.c
index c3ac98a..f55ac38 100644
--- a/drivers/pci/hotplug/ibmphp_hpc.c
+++ b/drivers/pci/hotplug/ibmphp_hpc.c
@@ -531,7 +531,7 @@
 *
 * Action:  issue a READ command to HPC
 *
-* Input:   pslot   - can not be NULL for READ_ALLSTAT
+* Input:   pslot   - cannot be NULL for READ_ALLSTAT
 *          pstatus - can be NULL for READ_ALLSTAT
 *
 * Return   0 or error codes
diff --git a/drivers/pci/hotplug/ibmphp_pci.c b/drivers/pci/hotplug/ibmphp_pci.c
index d87a9e3..d8f05d7 100644
--- a/drivers/pci/hotplug/ibmphp_pci.c
+++ b/drivers/pci/hotplug/ibmphp_pci.c
@@ -1371,12 +1371,12 @@
 	}
 
 	bus = ibmphp_find_res_bus (sec_number);
-	debug ("bus->busno is %x\n", bus->busno);
-	debug ("sec_number is %x\n", sec_number);
 	if (!bus) {
 		err ("cannot find Bus structure for the bridged device\n");
 		return -EINVAL;
 	}
+	debug("bus->busno is %x\n", bus->busno);
+	debug("sec_number is %x\n", sec_number);
 
 	ibmphp_remove_bus (bus, busno);
 
diff --git a/drivers/pci/hotplug/pciehp_core.c b/drivers/pci/hotplug/pciehp_core.c
index f93e81e..f13f313 100644
--- a/drivers/pci/hotplug/pciehp_core.c
+++ b/drivers/pci/hotplug/pciehp_core.c
@@ -521,14 +521,9 @@
 
 }
 
-static int hpdriver_context = 0;
-
 static void pciehp_remove (struct pcie_device *device)
 {
-	printk("%s ENTRY\n", __FUNCTION__);	
-	printk("%s -> Call free_irq for irq = %d\n",  
-		__FUNCTION__, device->irq);
-	free_irq(device->irq, &hpdriver_context);
+	/* XXX - Needs to be adapted to device driver model */
 }
 
 #ifdef CONFIG_PM
diff --git a/drivers/pci/hotplug/pciehp_hpc.c b/drivers/pci/hotplug/pciehp_hpc.c
index 1c551c6..6d3f580 100644
--- a/drivers/pci/hotplug/pciehp_hpc.c
+++ b/drivers/pci/hotplug/pciehp_hpc.c
@@ -718,8 +718,6 @@
 		if (php_ctlr->irq) {
 			free_irq(php_ctlr->irq, ctrl);
 			php_ctlr->irq = 0;
-			if (!pcie_mch_quirk) 
-				pci_disable_msi(php_ctlr->pci_dev);
 		}
 	}
 	if (php_ctlr->pci_dev) 
diff --git a/drivers/pci/hotplug/rpadlpar_core.c b/drivers/pci/hotplug/rpadlpar_core.c
index 46825fe..7238346 100644
--- a/drivers/pci/hotplug/rpadlpar_core.c
+++ b/drivers/pci/hotplug/rpadlpar_core.c
@@ -63,7 +63,7 @@
 	char *type;
 	int rc;
 
-	while ((np = of_find_node_by_type(np, "pci"))) {
+	while ((np = of_find_node_by_name(np, "pci"))) {
 		rc = rpaphp_get_drc_props(np, NULL, &name, &type, NULL);
 		if (rc == 0)
 			if (!strcmp(drc_name, name) && !strcmp(drc_type, type))
diff --git a/drivers/pci/hotplug/rpaphp_core.c b/drivers/pci/hotplug/rpaphp_core.c
index 141486d..71a2cb8 100644
--- a/drivers/pci/hotplug/rpaphp_core.c
+++ b/drivers/pci/hotplug/rpaphp_core.c
@@ -356,7 +356,7 @@
 	info(DRIVER_DESC " version: " DRIVER_VERSION "\n");
 	init_MUTEX(&rpaphp_sem);
 
-	while ((dn = of_find_node_by_type(dn, "pci")))
+	while ((dn = of_find_node_by_name(dn, "pci")))
 		rpaphp_add_slot(dn);
 
 	return 0;
diff --git a/drivers/pci/hotplug/sgi_hotplug.c b/drivers/pci/hotplug/sgi_hotplug.c
index b62ad31..5d188c5 100644
--- a/drivers/pci/hotplug/sgi_hotplug.c
+++ b/drivers/pci/hotplug/sgi_hotplug.c
@@ -205,21 +205,6 @@
 	return bss_hotplug_slot;
 }
 
-static void sn_bus_alloc_data(struct pci_dev *dev)
-{
-	struct pci_bus *subordinate_bus;
-	struct pci_dev *child;
-
-	sn_pci_fixup_slot(dev);
-
-	/* Recursively sets up the sn_irq_info structs */
-	if (dev->subordinate) {
-		subordinate_bus = dev->subordinate;
-		list_for_each_entry(child, &subordinate_bus->devices, bus_list)
-			sn_bus_alloc_data(child);
-	}
-}
-
 static void sn_bus_free_data(struct pci_dev *dev)
 {
 	struct pci_bus *subordinate_bus;
@@ -337,6 +322,11 @@
 	return rc;
 }
 
+/*
+ * Power up and configure the slot via a SAL call to PROM.
+ * Scan slot (and any children), do any platform specific fixup,
+ * and find device driver.
+ */
 static int enable_slot(struct hotplug_slot *bss_hotplug_slot)
 {
 	struct slot *slot = bss_hotplug_slot->private;
@@ -345,6 +335,7 @@
 	int func, num_funcs;
 	int new_ppb = 0;
 	int rc;
+	void pcibios_fixup_device_resources(struct pci_dev *);
 
 	/* Serialize the Linux PCI infrastructure */
 	mutex_lock(&sn_hotplug_mutex);
@@ -367,9 +358,6 @@
 		return -ENODEV;
 	}
 
-	sn_pci_controller_fixup(pci_domain_nr(slot->pci_bus),
-				slot->pci_bus->number,
-				slot->pci_bus);
 	/*
 	 * Map SN resources for all functions on the card
 	 * to the Linux PCI interface and tell the drivers
@@ -380,6 +368,13 @@
 				   PCI_DEVFN(slot->device_num + 1,
 					     PCI_FUNC(func)));
 		if (dev) {
+			/* Need to do slot fixup on PPB before fixup of children
+			 * (PPB's pcidev_info needs to be in pcidev_info list
+			 * before child's SN_PCIDEV_INFO() call to setup
+			 * pdi_host_pcidev_info).
+			 */
+			pcibios_fixup_device_resources(dev);
+			sn_pci_fixup_slot(dev);
 			if (dev->hdr_type == PCI_HEADER_TYPE_BRIDGE) {
 				unsigned char sec_bus;
 				pci_read_config_byte(dev, PCI_SECONDARY_BUS,
@@ -387,12 +382,8 @@
 				new_bus = pci_add_new_bus(dev->bus, dev,
 							  sec_bus);
 				pci_scan_child_bus(new_bus);
-				sn_pci_controller_fixup(pci_domain_nr(new_bus),
-							new_bus->number,
-							new_bus);
 				new_ppb = 1;
 			}
-			sn_bus_alloc_data(dev);
 			pci_dev_put(dev);
 		}
 	}
diff --git a/drivers/pci/msi.h b/drivers/pci/msi.h
index f0cca17..3898f52 100644
--- a/drivers/pci/msi.h
+++ b/drivers/pci/msi.h
@@ -6,14 +6,6 @@
 #ifndef MSI_H
 #define MSI_H
 
-/*
- * MSI-X Address Register
- */
-#define PCI_MSIX_FLAGS_QSIZE		0x7FF
-#define PCI_MSIX_FLAGS_ENABLE		(1 << 15)
-#define PCI_MSIX_FLAGS_BIRMASK		(7 << 0)
-#define PCI_MSIX_FLAGS_BITMASK		(1 << 0)
-
 #define PCI_MSIX_ENTRY_SIZE			16
 #define  PCI_MSIX_ENTRY_LOWER_ADDR_OFFSET	0
 #define  PCI_MSIX_ENTRY_UPPER_ADDR_OFFSET	4
diff --git a/drivers/pci/pci-acpi.c b/drivers/pci/pci-acpi.c
index bb7456c..a064f36 100644
--- a/drivers/pci/pci-acpi.c
+++ b/drivers/pci/pci-acpi.c
@@ -36,6 +36,7 @@
 	struct acpi_buffer	output = {ACPI_ALLOCATE_BUFFER, NULL};
 	union acpi_object 	*out_obj;
 	u32			osc_dw0;
+	acpi_status *ret_status = (acpi_status *)retval;
 
 	
 	/* Setting up input parameters */
@@ -56,6 +57,7 @@
 	if (ACPI_FAILURE (status)) {
 		printk(KERN_DEBUG  
 			"Evaluate _OSC Set fails. Status = 0x%04x\n", status);
+		*ret_status = status;
 		return status;
 	}
 	out_obj = output.pointer;
@@ -90,6 +92,7 @@
 
 query_osc_out:
 	kfree(output.pointer);
+	*ret_status = status;
 	return status;
 }
 
@@ -166,6 +169,7 @@
 acpi_status pci_osc_support_set(u32 flags)
 {
 	u32 temp;
+	acpi_status retval;
 
 	if (!(flags & OSC_SUPPORT_MASKS)) {
 		return AE_TYPE;
@@ -179,9 +183,13 @@
 	acpi_get_devices ( PCI_ROOT_HID_STRING,
 			acpi_query_osc,
 			ctrlset_buf,
-			NULL );
+			(void **) &retval );
 	ctrlset_buf[OSC_QUERY_TYPE] = !OSC_QUERY_ENABLE;
 	ctrlset_buf[OSC_CONTROL_TYPE] = temp;
+	if (ACPI_FAILURE(retval)) {
+		/* no osc support at all */
+		ctrlset_buf[OSC_SUPPORT_TYPE] = 0;
+	}
 	return AE_OK;
 }
 EXPORT_SYMBOL(pci_osc_support_set);
diff --git a/drivers/pci/pci-driver.c b/drivers/pci/pci-driver.c
index 194f1d2..e5ae3a0 100644
--- a/drivers/pci/pci-driver.c
+++ b/drivers/pci/pci-driver.c
@@ -329,8 +329,8 @@
 	/* restore the PCI config space */
 	pci_restore_state(pci_dev);
 	/* if the device was enabled before suspend, reenable */
-	if (pci_dev->is_enabled)
-		retval = pci_enable_device(pci_dev);
+	if (atomic_read(&pci_dev->enable_cnt))
+		retval = __pci_enable_device(pci_dev);
 	/* if the device was busmaster before the suspend, make it busmaster again */
 	if (pci_dev->is_busmaster)
 		pci_set_master(pci_dev);
@@ -445,9 +445,12 @@
 
 	/* register with core */
 	error = driver_register(&drv->driver);
+	if (error)
+		return error;
 
-	if (!error)
-		error = pci_create_newid_file(drv);
+	error = pci_create_newid_file(drv);
+	if (error)
+		driver_unregister(&drv->driver);
 
 	return error;
 }
diff --git a/drivers/pci/pci-sysfs.c b/drivers/pci/pci-sysfs.c
index f952bfe..7a94076 100644
--- a/drivers/pci/pci-sysfs.c
+++ b/drivers/pci/pci-sysfs.c
@@ -42,7 +42,6 @@
 pci_config_attr(subsystem_device, "0x%04x\n");
 pci_config_attr(class, "0x%06x\n");
 pci_config_attr(irq, "%u\n");
-pci_config_attr(is_enabled, "%u\n");
 
 static ssize_t broken_parity_status_show(struct device *dev,
 					 struct device_attribute *attr,
@@ -112,26 +111,36 @@
 		       (u8)(pci_dev->class >> 16), (u8)(pci_dev->class >> 8),
 		       (u8)(pci_dev->class));
 }
-static ssize_t
-is_enabled_store(struct device *dev, struct device_attribute *attr,
-		const char *buf, size_t count)
+
+static ssize_t is_enabled_store(struct device *dev,
+				struct device_attribute *attr, const char *buf,
+				size_t count)
 {
+	ssize_t result = -EINVAL;
 	struct pci_dev *pdev = to_pci_dev(dev);
-	int retval = 0;
 
 	/* this can crash the machine when done on the "wrong" device */
 	if (!capable(CAP_SYS_ADMIN))
 		return count;
 
-	if (*buf == '0')
-		pci_disable_device(pdev);
+	if (*buf == '0') {
+		if (atomic_read(&pdev->enable_cnt) != 0)
+			pci_disable_device(pdev);
+		else
+			result = -EIO;
+	} else if (*buf == '1')
+		result = pci_enable_device(pdev);
 
-	if (*buf == '1')
-		retval = pci_enable_device(pdev);
+	return result < 0 ? result : count;
+}
 
-	if (retval)
-		return retval;
-	return count;
+static ssize_t is_enabled_show(struct device *dev,
+			       struct device_attribute *attr, char *buf)
+{
+	struct pci_dev *pdev;
+
+	pdev = to_pci_dev (dev);
+	return sprintf (buf, "%u\n", atomic_read(&pdev->enable_cnt));
 }
 
 static ssize_t
diff --git a/drivers/pci/pci.c b/drivers/pci/pci.c
index a544997..5a14b73 100644
--- a/drivers/pci/pci.c
+++ b/drivers/pci/pci.c
@@ -490,6 +490,47 @@
 	kfree(save_state);
 }
 
+
+static int pci_save_pcix_state(struct pci_dev *dev)
+{
+	int pos, i = 0;
+	struct pci_cap_saved_state *save_state;
+	u16 *cap;
+
+	pos = pci_find_capability(dev, PCI_CAP_ID_PCIX);
+	if (pos <= 0)
+		return 0;
+
+	save_state = kzalloc(sizeof(*save_state) + sizeof(u16), GFP_KERNEL);
+	if (!save_state) {
+		dev_err(&dev->dev, "Out of memory in pci_save_pcie_state\n");
+		return -ENOMEM;
+	}
+	cap = (u16 *)&save_state->data[0];
+
+	pci_read_config_word(dev, pos + PCI_X_CMD, &cap[i++]);
+	pci_add_saved_cap(dev, save_state);
+	return 0;
+}
+
+static void pci_restore_pcix_state(struct pci_dev *dev)
+{
+	int i = 0, pos;
+	struct pci_cap_saved_state *save_state;
+	u16 *cap;
+
+	save_state = pci_find_saved_cap(dev, PCI_CAP_ID_PCIX);
+	pos = pci_find_capability(dev, PCI_CAP_ID_PCIX);
+	if (!save_state || pos <= 0)
+		return;
+	cap = (u16 *)&save_state->data[0];
+
+	pci_write_config_word(dev, pos + PCI_X_CMD, cap[i++]);
+	pci_remove_saved_cap(save_state);
+	kfree(save_state);
+}
+
+
 /**
  * pci_save_state - save the PCI configuration space of a device before suspending
  * @dev: - PCI device that we're dealing with
@@ -507,6 +548,8 @@
 		return i;
 	if ((i = pci_save_pcie_state(dev)) != 0)
 		return i;
+	if ((i = pci_save_pcix_state(dev)) != 0)
+		return i;
 	return 0;
 }
 
@@ -538,6 +581,7 @@
 				dev->saved_config_space[i]);
 		}
 	}
+	pci_restore_pcix_state(dev);
 	pci_restore_msi_state(dev);
 	pci_restore_msix_state(dev);
 	return 0;
@@ -568,27 +612,48 @@
 }
 
 /**
+ * __pci_enable_device - Initialize device before it's used by a driver.
+ * @dev: PCI device to be initialized
+ *
+ *  Initialize device before it's used by a driver. Ask low-level code
+ *  to enable I/O and memory. Wake up the device if it was suspended.
+ *  Beware, this function can fail.
+ *
+ * Note this function is a backend and is not supposed to be called by
+ * normal code, use pci_enable_device() instead.
+ */
+int
+__pci_enable_device(struct pci_dev *dev)
+{
+	int err;
+
+	err = pci_enable_device_bars(dev, (1 << PCI_NUM_RESOURCES) - 1);
+	if (err)
+		return err;
+	pci_fixup_device(pci_fixup_enable, dev);
+	return 0;
+}
+
+/**
  * pci_enable_device - Initialize device before it's used by a driver.
  * @dev: PCI device to be initialized
  *
  *  Initialize device before it's used by a driver. Ask low-level code
  *  to enable I/O and memory. Wake up the device if it was suspended.
  *  Beware, this function can fail.
+ *
+ *  Note we don't actually enable the device many times if we call
+ *  this function repeatedly (we just increment the count).
  */
-int
-pci_enable_device(struct pci_dev *dev)
+int pci_enable_device(struct pci_dev *dev)
 {
-	int err;
-
-	if (dev->is_enabled)
-		return 0;
-
-	err = pci_enable_device_bars(dev, (1 << PCI_NUM_RESOURCES) - 1);
-	if (err)
-		return err;
-	pci_fixup_device(pci_fixup_enable, dev);
-	dev->is_enabled = 1;
-	return 0;
+	int result;
+	if (atomic_add_return(1, &dev->enable_cnt) > 1)
+		return 0;		/* already enabled */
+	result = __pci_enable_device(dev);
+	if (result < 0)
+		atomic_dec(&dev->enable_cnt);
+	return result;
 }
 
 /**
@@ -607,12 +672,18 @@
  *
  * Signal to the system that the PCI device is not in use by the system
  * anymore.  This only involves disabling PCI bus-mastering, if active.
+ *
+ * Note we don't actually disable the device until all callers of
+ * pci_device_enable() have called pci_device_disable().
  */
 void
 pci_disable_device(struct pci_dev *dev)
 {
 	u16 pci_command;
 
+	if (atomic_sub_return(1, &dev->enable_cnt) != 0)
+		return;
+
 	if (dev->msi_enabled)
 		disable_msi_mode(dev, pci_find_capability(dev, PCI_CAP_ID_MSI),
 			PCI_CAP_ID_MSI);
@@ -628,7 +699,6 @@
 	dev->is_busmaster = 0;
 
 	pcibios_disable_device(dev);
-	dev->is_enabled = 0;
 }
 
 /**
@@ -831,22 +901,38 @@
 	pcibios_set_master(dev);
 }
 
-#ifndef HAVE_ARCH_PCI_MWI
+#ifdef PCI_DISABLE_MWI
+int pci_set_mwi(struct pci_dev *dev)
+{
+	return 0;
+}
+
+void pci_clear_mwi(struct pci_dev *dev)
+{
+}
+
+#else
+
+#ifndef PCI_CACHE_LINE_BYTES
+#define PCI_CACHE_LINE_BYTES L1_CACHE_BYTES
+#endif
+
 /* This can be overridden by arch code. */
-u8 pci_cache_line_size = L1_CACHE_BYTES >> 2;
+/* Don't forget this is measured in 32-bit words, not bytes */
+u8 pci_cache_line_size = PCI_CACHE_LINE_BYTES / 4;
 
 /**
- * pci_generic_prep_mwi - helper function for pci_set_mwi
- * @dev: the PCI device for which MWI is enabled
+ * pci_set_cacheline_size - ensure the CACHE_LINE_SIZE register is programmed
+ * @dev: the PCI device for which MWI is to be enabled
  *
- * Helper function for generic implementation of pcibios_prep_mwi
- * function.  Originally copied from drivers/net/acenic.c.
+ * Helper function for pci_set_mwi.
+ * Originally copied from drivers/net/acenic.c.
  * Copyright 1998-2001 by Jes Sorensen, <jes@trained-monkey.org>.
  *
  * RETURNS: An appropriate -ERRNO error value on error, or zero for success.
  */
 static int
-pci_generic_prep_mwi(struct pci_dev *dev)
+pci_set_cacheline_size(struct pci_dev *dev)
 {
 	u8 cacheline_size;
 
@@ -872,7 +958,6 @@
 
 	return -EINVAL;
 }
-#endif /* !HAVE_ARCH_PCI_MWI */
 
 /**
  * pci_set_mwi - enables memory-write-invalidate PCI transaction
@@ -890,12 +975,7 @@
 	int rc;
 	u16 cmd;
 
-#ifdef HAVE_ARCH_PCI_MWI
-	rc = pcibios_prep_mwi(dev);
-#else
-	rc = pci_generic_prep_mwi(dev);
-#endif
-
+	rc = pci_set_cacheline_size(dev);
 	if (rc)
 		return rc;
 
@@ -926,6 +1006,7 @@
 		pci_write_config_word(dev, PCI_COMMAND, cmd);
 	}
 }
+#endif /* ! PCI_DISABLE_MWI */
 
 /**
  * pci_intx - enables/disables PCI INTx for device dev
diff --git a/drivers/pci/pci.h b/drivers/pci/pci.h
index 6bf327d..398852f 100644
--- a/drivers/pci/pci.h
+++ b/drivers/pci/pci.h
@@ -1,5 +1,6 @@
 /* Functions internal to the PCI core code */
 
+extern int __must_check __pci_enable_device(struct pci_dev *);
 extern int pci_uevent(struct device *dev, char **envp, int num_envp,
 		      char *buffer, int buffer_size);
 extern int pci_create_sysfs_dev_files(struct pci_dev *pdev);
diff --git a/drivers/pci/probe.c b/drivers/pci/probe.c
index e159d66..0eeac60 100644
--- a/drivers/pci/probe.c
+++ b/drivers/pci/probe.c
@@ -679,6 +679,33 @@
 		pci_read_bases(dev, 6, PCI_ROM_ADDRESS);
 		pci_read_config_word(dev, PCI_SUBSYSTEM_VENDOR_ID, &dev->subsystem_vendor);
 		pci_read_config_word(dev, PCI_SUBSYSTEM_ID, &dev->subsystem_device);
+
+		/*
+		 *	Do the ugly legacy mode stuff here rather than broken chip
+		 *	quirk code. Legacy mode ATA controllers have fixed
+		 *	addresses. These are not always echoed in BAR0-3, and
+		 *	BAR0-3 in a few cases contain junk!
+		 */
+		if (class == PCI_CLASS_STORAGE_IDE) {
+			u8 progif;
+			pci_read_config_byte(dev, PCI_CLASS_PROG, &progif);
+			if ((progif & 1) == 0) {
+				dev->resource[0].start = 0x1F0;
+				dev->resource[0].end = 0x1F7;
+				dev->resource[0].flags = IORESOURCE_IO;
+				dev->resource[1].start = 0x3F6;
+				dev->resource[1].end = 0x3F6;
+				dev->resource[1].flags = IORESOURCE_IO;
+			}
+			if ((progif & 4) == 0) {
+				dev->resource[2].start = 0x170;
+				dev->resource[2].end = 0x177;
+				dev->resource[2].flags = IORESOURCE_IO;
+				dev->resource[3].start = 0x376;
+				dev->resource[3].end = 0x376;
+				dev->resource[3].flags = IORESOURCE_IO;
+			}
+		}
 		break;
 
 	case PCI_HEADER_TYPE_BRIDGE:		    /* bridge header */
diff --git a/drivers/pci/quirks.c b/drivers/pci/quirks.c
index 5b44838..9ca9b9b 100644
--- a/drivers/pci/quirks.c
+++ b/drivers/pci/quirks.c
@@ -797,56 +797,6 @@
 DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_CYRIX,	PCI_DEVICE_ID_CYRIX_PCI_MASTER, quirk_mediagx_master );
 
 /*
- * As per PCI spec, ignore base address registers 0-3 of the IDE controllers
- * running in Compatible mode (bits 0 and 2 in the ProgIf for primary and
- * secondary channels respectively). If the device reports Compatible mode
- * but does use BAR0-3 for address decoding, we assume that firmware has
- * programmed these BARs with standard values (0x1f0,0x3f4 and 0x170,0x374).
- * Exceptions (if they exist) must be handled in chip/architecture specific
- * fixups.
- *
- * Note: for non x86 people. You may need an arch specific quirk to handle
- * moving IDE devices to native mode as well. Some plug in card devices power
- * up in compatible mode and assume the BIOS will adjust them.
- *
- * Q: should we load the 0x1f0,0x3f4 into the registers or zap them as
- * we do now ? We don't want is pci_enable_device to come along
- * and assign new resources. Both approaches work for that.
- */ 
-static void __devinit quirk_ide_bases(struct pci_dev *dev)
-{
-       struct resource *res;
-       int first_bar = 2, last_bar = 0;
-
-       if ((dev->class >> 8) != PCI_CLASS_STORAGE_IDE)
-               return;
-
-       res = &dev->resource[0];
-
-       /* primary channel: ProgIf bit 0, BAR0, BAR1 */
-       if (!(dev->class & 1) && (res[0].flags || res[1].flags)) { 
-               res[0].start = res[0].end = res[0].flags = 0;
-               res[1].start = res[1].end = res[1].flags = 0;
-               first_bar = 0;
-               last_bar = 1;
-       }
-
-       /* secondary channel: ProgIf bit 2, BAR2, BAR3 */
-       if (!(dev->class & 4) && (res[2].flags || res[3].flags)) { 
-               res[2].start = res[2].end = res[2].flags = 0;
-               res[3].start = res[3].end = res[3].flags = 0;
-               last_bar = 3;
-       }
-
-       if (!last_bar)
-               return;
-
-       printk(KERN_INFO "PCI: Ignoring BAR%d-%d of IDE controller %s\n",
-              first_bar, last_bar, pci_name(dev));
-}
-DECLARE_PCI_FIXUP_HEADER(PCI_ANY_ID, PCI_ANY_ID, quirk_ide_bases);
-
-/*
  *	Ensure C0 rev restreaming is off. This is normally done by
  *	the BIOS but in the odd case it is not the results are corruption
  *	hence the presence of a Linux check
@@ -880,11 +830,10 @@
 		prog &= ~5;
 		pdev->class &= ~5;
 		pci_write_config_byte(pdev, PCI_CLASS_PROG, prog);
-		/* need to re-assign BARs for compat mode */
-		quirk_ide_bases(pdev);
+		/* PCI layer will sort out resources */
 	}
 }
-DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_SERVERWORKS, PCI_DEVICE_ID_SERVERWORKS_CSB5IDE, quirk_svwks_csb5ide );
+DECLARE_PCI_FIXUP_EARLY(PCI_VENDOR_ID_SERVERWORKS, PCI_DEVICE_ID_SERVERWORKS_CSB5IDE, quirk_svwks_csb5ide );
 
 /*
  *	Intel 82801CAM ICH3-M datasheet says IDE modes must be the same
@@ -900,11 +849,9 @@
 		prog &= ~5;
 		pdev->class &= ~5;
 		pci_write_config_byte(pdev, PCI_CLASS_PROG, prog);
-		/* need to re-assign BARs for compat mode */
-		quirk_ide_bases(pdev);
 	}
 }
-DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82801CA_10, quirk_ide_samemode);
+DECLARE_PCI_FIXUP_EARLY(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82801CA_10, quirk_ide_samemode);
 
 /* This was originally an Alpha specific thing, but it really fits here.
  * The i82375 PCI/EISA bridge appears as non-classified. Fix that.
diff --git a/drivers/pci/rom.c b/drivers/pci/rom.c
index e1dcefc..d087e08 100644
--- a/drivers/pci/rom.c
+++ b/drivers/pci/rom.c
@@ -81,7 +81,8 @@
 		start = (loff_t)0xC0000;
 		*size = 0x20000; /* cover C000:0 through E000:0 */
 	} else {
-		if (res->flags & IORESOURCE_ROM_COPY) {
+		if (res->flags &
+			(IORESOURCE_ROM_COPY | IORESOURCE_ROM_BIOS_COPY)) {
 			*size = pci_resource_len(pdev, PCI_ROM_RESOURCE);
 			return (void __iomem *)(unsigned long)
 				pci_resource_start(pdev, PCI_ROM_RESOURCE);
@@ -165,7 +166,8 @@
 	if (!rom)
 		return NULL;
 
-	if (res->flags & (IORESOURCE_ROM_COPY | IORESOURCE_ROM_SHADOW))
+	if (res->flags & (IORESOURCE_ROM_COPY | IORESOURCE_ROM_SHADOW |
+			  IORESOURCE_ROM_BIOS_COPY))
 		return rom;
 
 	res->start = (unsigned long)kmalloc(*size, GFP_KERNEL);
@@ -191,7 +193,7 @@
 {
 	struct resource *res = &pdev->resource[PCI_ROM_RESOURCE];
 
-	if (res->flags & IORESOURCE_ROM_COPY)
+	if (res->flags & (IORESOURCE_ROM_COPY | IORESOURCE_ROM_BIOS_COPY))
 		return;
 
 	iounmap(rom);
@@ -215,6 +217,7 @@
 		sysfs_remove_bin_file(&pdev->dev.kobj, pdev->rom_attr);
 	if (!(res->flags & (IORESOURCE_ROM_ENABLE |
 			    IORESOURCE_ROM_SHADOW |
+			    IORESOURCE_ROM_BIOS_COPY |
 			    IORESOURCE_ROM_COPY)))
 		pci_disable_rom(pdev);
 }
diff --git a/drivers/s390/net/claw.h b/drivers/s390/net/claw.h
index 969be46..1ee9a6f 100644
--- a/drivers/s390/net/claw.h
+++ b/drivers/s390/net/claw.h
@@ -29,7 +29,7 @@
 #define CLAW_COMPLETE           0xff   /* flag to indicate i/o completed */
 
 /*-----------------------------------------------------*
-*     CLAW control comand code                         *
+*     CLAW control command code                        *
 *------------------------------------------------------*/
 
 #define SYSTEM_VALIDATE_REQUEST   0x01  /* System Validate request */
diff --git a/drivers/scsi/aic94xx/aic94xx_reg_def.h b/drivers/scsi/aic94xx/aic94xx_reg_def.h
index b79f45f..a11f4e6 100644
--- a/drivers/scsi/aic94xx/aic94xx_reg_def.h
+++ b/drivers/scsi/aic94xx/aic94xx_reg_def.h
@@ -2000,7 +2000,7 @@
  * The host accesses this scratch in a different manner from the
  * central sequencer. The sequencer has to use CSEQ registers CSCRPAGE
  * and CMnSCRPAGE to access the scratch memory. A flat mapping of the
- * scratch memory is avaliable for software convenience and to prevent
+ * scratch memory is available for software convenience and to prevent
  * corruption while the sequencer is running. This memory is mapped
  * onto addresses 800h - BFFh, total of 400h bytes.
  *
diff --git a/drivers/scsi/aic94xx/aic94xx_sds.c b/drivers/scsi/aic94xx/aic94xx_sds.c
index de7c04d..e5a0ec3 100644
--- a/drivers/scsi/aic94xx/aic94xx_sds.c
+++ b/drivers/scsi/aic94xx/aic94xx_sds.c
@@ -64,7 +64,7 @@
 
 #define OCM_INIT_DIR_ENTRIES	5
 /***************************************************************************
-*  OCM dircetory default
+*  OCM directory default
 ***************************************************************************/
 static struct asd_ocm_dir OCMDirInit =
 {
@@ -73,7 +73,7 @@
 };
 
 /***************************************************************************
-*  OCM dircetory Entries default
+*  OCM directory Entries default
 ***************************************************************************/
 static struct asd_ocm_dir_ent OCMDirEntriesInit[OCM_INIT_DIR_ENTRIES] =
 {
diff --git a/drivers/scsi/ncr53c8xx.c b/drivers/scsi/ncr53c8xx.c
index 6cc2bc2..adb8eb4 100644
--- a/drivers/scsi/ncr53c8xx.c
+++ b/drivers/scsi/ncr53c8xx.c
@@ -185,7 +185,7 @@
 **	power of 2 cache line size.
 **	Enhanced in linux-2.3.44 to provide a memory pool 
 **	per pcidev to support dynamic dma mapping. (I would 
-**	have preferred a real bus astraction, btw).
+**	have preferred a real bus abstraction, btw).
 **
 **==========================================================
 */
@@ -1438,7 +1438,7 @@
 **	The first four bytes (scr_st[4]) are used inside the script by 
 **	"COPY" commands.
 **	Because source and destination must have the same alignment
-**	in a DWORD, the fields HAVE to be at the choosen offsets.
+**	in a DWORD, the fields HAVE to be at the chosen offsets.
 **		xerr_st		0	(0x34)	scratcha
 **		sync_st		1	(0x05)	sxfer
 **		wide_st		3	(0x03)	scntl3
@@ -1498,7 +1498,7 @@
 **	the DSA (data structure address) register points
 **	to this substructure of the ccb.
 **	This substructure contains the header with
-**	the script-processor-changable data and
+**	the script-processor-changeable data and
 **	data blocks for the indirect move commands.
 **
 **----------------------------------------------------------
@@ -5107,7 +5107,7 @@
 
 /*
 **	This CCB has been skipped by the NCR.
-**	Queue it in the correponding unit queue.
+**	Queue it in the corresponding unit queue.
 */
 static void ncr_ccb_skipped(struct ncb *np, struct ccb *cp)
 {
@@ -5896,8 +5896,8 @@
 **
 **	In normal cases, interrupt conditions occur one at a 
 **	time. The ncr is able to stack in some extra registers 
-**	other interrupts that will occurs after the first one.
-**	But severall interrupts may occur at the same time.
+**	other interrupts that will occur after the first one.
+**	But, several interrupts may occur at the same time.
 **
 **	We probably should only try to deal with the normal 
 **	case, but it seems that multiple interrupts occur in 
@@ -6796,7 +6796,7 @@
 **	The host status field is set to HS_NEGOTIATE to mark this
 **	situation.
 **
-**	If the target doesn't answer this message immidiately
+**	If the target doesn't answer this message immediately
 **	(as required by the standard), the SIR_NEGO_FAIL interrupt
 **	will be raised eventually.
 **	The handler removes the HS_NEGOTIATE status, and sets the
diff --git a/drivers/scsi/ncr53c8xx.h b/drivers/scsi/ncr53c8xx.h
index cb8b770..b39357d 100644
--- a/drivers/scsi/ncr53c8xx.h
+++ b/drivers/scsi/ncr53c8xx.h
@@ -218,7 +218,7 @@
 **	Same as option 1, but also deal with 
 **	misconfigured interrupts.
 **
-**	- Edge triggerred instead of level sensitive.
+**	- Edge triggered instead of level sensitive.
 **	- No interrupt line connected.
 **	- IRQ number misconfigured.
 **	
@@ -549,7 +549,7 @@
 
 /*
 **	Initial setup.
-**	Can be overriden at startup by a command line.
+**	Can be overridden at startup by a command line.
 */
 #define SCSI_NCR_DRIVER_SETUP			\
 {						\
@@ -1093,7 +1093,7 @@
 **-----------------------------------------------------------
 **	On 810A, 860, 825A, 875, 895 and 896 chips the content 
 **	of SFBR register can be used as data (SCR_SFBR_DATA).
-**	The 896 has additionnal IO registers starting at 
+**	The 896 has additional IO registers starting at 
 **	offset 0x80. Bit 7 of register offset is stored in 
 **	bit 7 of the SCRIPTS instruction first DWORD.
 **-----------------------------------------------------------
diff --git a/drivers/spi/Kconfig b/drivers/spi/Kconfig
index 23334c8..d895a1a 100644
--- a/drivers/spi/Kconfig
+++ b/drivers/spi/Kconfig
@@ -16,7 +16,7 @@
 	  controller and a chipselect.  Most SPI slaves don't support
 	  dynamic device discovery; some are even write-only or read-only.
 
-	  SPI is widely used by microcontollers to talk with sensors,
+	  SPI is widely used by microcontrollers to talk with sensors,
 	  eeprom and flash memory, codecs and various other controller
 	  chips, analog to digital (and d-to-a) converters, and more.
 	  MMC and SD cards can be accessed using SPI protocol; and for
diff --git a/drivers/usb/atm/speedtch.c b/drivers/usb/atm/speedtch.c
index c870c80..a823486 100644
--- a/drivers/usb/atm/speedtch.c
+++ b/drivers/usb/atm/speedtch.c
@@ -834,8 +834,8 @@
 			const struct usb_endpoint_descriptor *endpoint_desc = &desc->endpoint[i].desc;
 
 			if ((endpoint_desc->bEndpointAddress == target_address)) {
-				use_isoc = (endpoint_desc->bmAttributes & USB_ENDPOINT_XFERTYPE_MASK) ==
-					USB_ENDPOINT_XFER_ISOC;
+				use_isoc =
+					usb_endpoint_xfer_isoc(endpoint_desc);
 				break;
 			}
 		}
diff --git a/drivers/usb/atm/ueagle-atm.c b/drivers/usb/atm/ueagle-atm.c
index f6b9f7e..c137c04 100644
--- a/drivers/usb/atm/ueagle-atm.c
+++ b/drivers/usb/atm/ueagle-atm.c
@@ -401,9 +401,8 @@
 	int ret = -ENOMEM;
 	u8 *xfer_buff;
 
-	xfer_buff = kmalloc(size, GFP_KERNEL);
+	xfer_buff = kmemdup(buff, size, GFP_KERNEL);
 	if (xfer_buff) {
-		memcpy(xfer_buff, buff, size);
 		ret = usb_control_msg(usb,
 				      usb_sndctrlpipe(usb, 0),
 				      LOAD_INTERNAL,
@@ -595,14 +594,12 @@
 	u8 *xfer_buff;
 	int bytes_read;
 
-	xfer_buff = kmalloc(size, GFP_KERNEL);
+	xfer_buff = kmemdup(data, size, GFP_KERNEL);
 	if (!xfer_buff) {
 		uea_err(INS_TO_USBDEV(sc), "can't allocate xfer_buff\n");
 		return ret;
 	}
 
-	memcpy(xfer_buff, data, size);
-
 	ret = usb_bulk_msg(sc->usb_dev,
 			 usb_sndbulkpipe(sc->usb_dev, UEA_IDMA_PIPE),
 			 xfer_buff, size, &bytes_read, BULK_TIMEOUT);
@@ -765,12 +762,11 @@
 	u8 *xfer_buff;
 	int ret = -ENOMEM;
 
-	xfer_buff = kmalloc(size, GFP_KERNEL);
+	xfer_buff = kmemdup(data, size, GFP_KERNEL);
 	if (!xfer_buff) {
 		uea_err(INS_TO_USBDEV(sc), "can't allocate xfer_buff\n");
 		return ret;
 	}
-	memcpy(xfer_buff, data, size);
 
 	ret = usb_control_msg(sc->usb_dev, usb_sndctrlpipe(sc->usb_dev, 0),
 			      UCDC_SEND_ENCAPSULATED_COMMAND,
diff --git a/drivers/usb/class/cdc-acm.c b/drivers/usb/class/cdc-acm.c
index 9a9012f..ec3438d 100644
--- a/drivers/usb/class/cdc-acm.c
+++ b/drivers/usb/class/cdc-acm.c
@@ -892,7 +892,7 @@
 
 
 	/* workaround for switched endpoints */
-	if ((epread->bEndpointAddress & USB_DIR_IN) != USB_DIR_IN) {
+	if (!usb_endpoint_dir_in(epread)) {
 		/* descriptors are swapped */
 		struct usb_endpoint_descriptor *t;
 		dev_dbg(&intf->dev,"The data interface has switched endpoints");
diff --git a/drivers/usb/core/Kconfig b/drivers/usb/core/Kconfig
index 6e3b535..f8324d8 100644
--- a/drivers/usb/core/Kconfig
+++ b/drivers/usb/core/Kconfig
@@ -72,6 +72,21 @@
 
 	  If you are unsure about this, say N here.
 
+config USB_MULTITHREAD_PROBE
+	bool "USB Multi-threaded probe (EXPERIMENTAL)"
+	depends on USB && EXPERIMENTAL
+	default n
+	help
+	  Say Y here if you want the USB core to spawn a new thread for
+	  every USB device that is probed.  This can cause a small speedup
+	  in boot times on systems with a lot of different USB devices.
+
+	  This option should be safe to enable, but if any odd probing
+	  problems are found, please disable it, or dynamically turn it
+	  off in the /sys/module/usbcore/parameters/multithread_probe
+	  file
+
+	  When in doubt, say N.
 
 config USB_OTG
 	bool
diff --git a/drivers/usb/core/devices.c b/drivers/usb/core/devices.c
index 3538c2f..ea398e5 100644
--- a/drivers/usb/core/devices.c
+++ b/drivers/usb/core/devices.c
@@ -175,12 +175,13 @@
 )
 {
 	char dir, unit, *type;
-	unsigned interval, in, bandwidth = 1;
+	unsigned interval, bandwidth = 1;
 
 	if (start > end)
 		return start;
-	in = (desc->bEndpointAddress & USB_DIR_IN);
-	dir = in ? 'I' : 'O';
+
+	dir = usb_endpoint_dir_in(desc) ? 'I' : 'O';
+
 	if (speed == USB_SPEED_HIGH) {
 		switch (le16_to_cpu(desc->wMaxPacketSize) & (0x03 << 11)) {
 		case 1 << 11:	bandwidth = 2; break;
@@ -204,7 +205,7 @@
 		break;
 	case USB_ENDPOINT_XFER_BULK:
 		type = "Bulk";
-		if (speed == USB_SPEED_HIGH && !in)	/* uframes per NAK */
+		if (speed == USB_SPEED_HIGH && dir == 'O') /* uframes per NAK */
 			interval = desc->bInterval;
 		else
 			interval = 0;
diff --git a/drivers/usb/core/devio.c b/drivers/usb/core/devio.c
index fed92be..3ed4cb2 100644
--- a/drivers/usb/core/devio.c
+++ b/drivers/usb/core/devio.c
@@ -561,7 +561,7 @@
 		dev = inode->i_private;
 	if (!dev)
 		goto out;
-	ret = usb_autoresume_device(dev, 1);
+	ret = usb_autoresume_device(dev);
 	if (ret)
 		goto out;
 
@@ -609,7 +609,7 @@
 			releaseintf(ps, ifnum);
 	}
 	destroy_all_async(ps);
-	usb_autosuspend_device(dev, 1);
+	usb_autosuspend_device(dev);
 	usb_unlock_device(dev);
 	usb_put_dev(dev);
 	put_pid(ps->disc_pid);
diff --git a/drivers/usb/core/driver.c b/drivers/usb/core/driver.c
index 113e484..d6eb5ce 100644
--- a/drivers/usb/core/driver.c
+++ b/drivers/usb/core/driver.c
@@ -205,7 +205,7 @@
 	if (id) {
 		dev_dbg(dev, "%s - got id\n", __FUNCTION__);
 
-		error = usb_autoresume_device(udev, 1);
+		error = usb_autoresume_device(udev);
 		if (error)
 			return error;
 
@@ -229,7 +229,7 @@
 		} else
 			intf->condition = USB_INTERFACE_BOUND;
 
-		usb_autosuspend_device(udev, 1);
+		usb_autosuspend_device(udev);
 	}
 
 	return error;
@@ -247,7 +247,7 @@
 
 	/* Autoresume for set_interface call below */
 	udev = interface_to_usbdev(intf);
-	error = usb_autoresume_device(udev, 1);
+	error = usb_autoresume_device(udev);
 
 	/* release all urbs for this interface */
 	usb_disable_interface(interface_to_usbdev(intf), intf);
@@ -265,7 +265,7 @@
 	intf->needs_remote_wakeup = 0;
 
 	if (!error)
-		usb_autosuspend_device(udev, 1);
+		usb_autosuspend_device(udev);
 
 	return 0;
 }
@@ -408,6 +408,16 @@
 	    (id->bDeviceProtocol != dev->descriptor.bDeviceProtocol))
 		return 0;
 
+	/* The interface class, subclass, and protocol should never be
+	 * checked for a match if the device class is Vendor Specific,
+	 * unless the match record specifies the Vendor ID. */
+	if (dev->descriptor.bDeviceClass == USB_CLASS_VENDOR_SPEC &&
+			!(id->match_flags & USB_DEVICE_ID_MATCH_VENDOR) &&
+			(id->match_flags & (USB_DEVICE_ID_MATCH_INT_CLASS |
+				USB_DEVICE_ID_MATCH_INT_SUBCLASS |
+				USB_DEVICE_ID_MATCH_INT_PROTOCOL)))
+		return 0;
+
 	if ((id->match_flags & USB_DEVICE_ID_MATCH_INT_CLASS) &&
 	    (id->bInterfaceClass != intf->desc.bInterfaceClass))
 		return 0;
@@ -476,7 +486,17 @@
  * most general; they let drivers bind to any interface on a
  * multiple-function device.  Use the USB_INTERFACE_INFO
  * macro, or its siblings, to match class-per-interface style
- * devices (as recorded in bDeviceClass).
+ * devices (as recorded in bInterfaceClass).
+ *
+ * Note that an entry created by USB_INTERFACE_INFO won't match
+ * any interface if the device class is set to Vendor-Specific.
+ * This is deliberate; according to the USB spec the meanings of
+ * the interface class/subclass/protocol for these devices are also
+ * vendor-specific, and hence matching against a standard product
+ * class wouldn't work anyway.  If you really want to use an
+ * interface-based match for such a device, create a match record
+ * that also specifies the vendor ID.  (Unforunately there isn't a
+ * standard macro for creating records like this.)
  *
  * Within those groups, remember that not all combinations are
  * meaningful.  For example, don't give a product version range
@@ -505,7 +525,7 @@
 }
 EXPORT_SYMBOL_GPL_FUTURE(usb_match_id);
 
-int usb_device_match(struct device *dev, struct device_driver *drv)
+static int usb_device_match(struct device *dev, struct device_driver *drv)
 {
 	/* devices and interfaces are handled separately */
 	if (is_usb_device(dev)) {
@@ -790,7 +810,7 @@
 #ifdef CONFIG_PM
 
 /* Caller has locked udev's pm_mutex */
-static int suspend_device(struct usb_device *udev, pm_message_t msg)
+static int usb_suspend_device(struct usb_device *udev, pm_message_t msg)
 {
 	struct usb_device_driver	*udriver;
 	int				status = 0;
@@ -817,7 +837,7 @@
 }
 
 /* Caller has locked udev's pm_mutex */
-static int resume_device(struct usb_device *udev)
+static int usb_resume_device(struct usb_device *udev)
 {
 	struct usb_device_driver	*udriver;
 	int				status = 0;
@@ -843,7 +863,7 @@
 }
 
 /* Caller has locked intf's usb_device's pm mutex */
-static int suspend_interface(struct usb_interface *intf, pm_message_t msg)
+static int usb_suspend_interface(struct usb_interface *intf, pm_message_t msg)
 {
 	struct usb_driver	*driver;
 	int			status = 0;
@@ -880,7 +900,7 @@
 }
 
 /* Caller has locked intf's usb_device's pm_mutex */
-static int resume_interface(struct usb_interface *intf)
+static int usb_resume_interface(struct usb_interface *intf)
 {
 	struct usb_driver	*driver;
 	int			status = 0;
@@ -920,6 +940,44 @@
 	return status;
 }
 
+#ifdef	CONFIG_USB_SUSPEND
+
+/* Internal routine to check whether we may autosuspend a device. */
+static int autosuspend_check(struct usb_device *udev)
+{
+	int			i;
+	struct usb_interface	*intf;
+
+	/* For autosuspend, fail fast if anything is in use.
+	 * Also fail if any interfaces require remote wakeup but it
+	 * isn't available. */
+	udev->do_remote_wakeup = device_may_wakeup(&udev->dev);
+	if (udev->pm_usage_cnt > 0)
+		return -EBUSY;
+	if (udev->actconfig) {
+		for (i = 0; i < udev->actconfig->desc.bNumInterfaces; i++) {
+			intf = udev->actconfig->interface[i];
+			if (!is_active(intf))
+				continue;
+			if (intf->pm_usage_cnt > 0)
+				return -EBUSY;
+			if (intf->needs_remote_wakeup &&
+					!udev->do_remote_wakeup) {
+				dev_dbg(&udev->dev, "remote wakeup needed "
+						"for autosuspend\n");
+				return -EOPNOTSUPP;
+			}
+		}
+	}
+	return 0;
+}
+
+#else
+
+#define autosuspend_check(udev)		0
+
+#endif
+
 /**
  * usb_suspend_both - suspend a USB device and its interfaces
  * @udev: the usb_device to suspend
@@ -971,52 +1029,34 @@
 
 	udev->do_remote_wakeup = device_may_wakeup(&udev->dev);
 
-	/* For autosuspend, fail fast if anything is in use.
-	 * Also fail if any interfaces require remote wakeup but it
-	 * isn't available. */
 	if (udev->auto_pm) {
-		if (udev->pm_usage_cnt > 0)
-			return -EBUSY;
-		if (udev->actconfig) {
-			for (; i < udev->actconfig->desc.bNumInterfaces; i++) {
-				intf = udev->actconfig->interface[i];
-				if (!is_active(intf))
-					continue;
-				if (intf->pm_usage_cnt > 0)
-					return -EBUSY;
-				if (intf->needs_remote_wakeup &&
-						!udev->do_remote_wakeup) {
-					dev_dbg(&udev->dev,
-	"remote wakeup needed for autosuspend\n");
-					return -EOPNOTSUPP;
-				}
-			}
-			i = 0;
-		}
+		status = autosuspend_check(udev);
+		if (status < 0)
+			return status;
 	}
 
 	/* Suspend all the interfaces and then udev itself */
 	if (udev->actconfig) {
 		for (; i < udev->actconfig->desc.bNumInterfaces; i++) {
 			intf = udev->actconfig->interface[i];
-			status = suspend_interface(intf, msg);
+			status = usb_suspend_interface(intf, msg);
 			if (status != 0)
 				break;
 		}
 	}
 	if (status == 0)
-		status = suspend_device(udev, msg);
+		status = usb_suspend_device(udev, msg);
 
 	/* If the suspend failed, resume interfaces that did get suspended */
 	if (status != 0) {
 		while (--i >= 0) {
 			intf = udev->actconfig->interface[i];
-			resume_interface(intf);
+			usb_resume_interface(intf);
 		}
 
 	/* If the suspend succeeded, propagate it up the tree */
 	} else if (parent)
-		usb_autosuspend_device(parent, 0);
+		usb_autosuspend_device(parent);
 
 	// dev_dbg(&udev->dev, "%s: status %d\n", __FUNCTION__, status);
 	return status;
@@ -1064,9 +1104,25 @@
 	/* Propagate the resume up the tree, if necessary */
 	if (udev->state == USB_STATE_SUSPENDED) {
 		if (parent) {
-			usb_pm_lock(parent);
-			parent->auto_pm = 1;
-			status = usb_resume_both(parent);
+			status = usb_autoresume_device(parent);
+			if (status == 0) {
+				status = usb_resume_device(udev);
+				if (status) {
+					usb_autosuspend_device(parent);
+
+					/* It's possible usb_resume_device()
+					 * failed after the port was
+					 * unsuspended, causing udev to be
+					 * logically disconnected.  We don't
+					 * want usb_disconnect() to autosuspend
+					 * the parent again, so tell it that
+					 * udev disconnected while still
+					 * suspended. */
+					if (udev->state ==
+							USB_STATE_NOTATTACHED)
+						udev->discon_suspended = 1;
+				}
+			}
 		} else {
 
 			/* We can't progagate beyond the USB subsystem,
@@ -1075,24 +1131,20 @@
 			if (udev->dev.parent->power.power_state.event !=
 					PM_EVENT_ON)
 				status = -EHOSTUNREACH;
-		}
-		if (status == 0)
-			status = resume_device(udev);
-		if (parent)
-			usb_pm_unlock(parent);
+			else
+				status = usb_resume_device(udev);
+ 		}
 	} else {
 
 		/* Needed only for setting udev->dev.power.power_state.event
 		 * and for possible debugging message. */
-		status = resume_device(udev);
+		status = usb_resume_device(udev);
 	}
 
-	/* Now the parent won't suspend until we are finished */
-
 	if (status == 0 && udev->actconfig) {
 		for (i = 0; i < udev->actconfig->desc.bNumInterfaces; i++) {
 			intf = udev->actconfig->interface[i];
-			resume_interface(intf);
+			usb_resume_interface(intf);
 		}
 	}
 
@@ -1102,39 +1154,53 @@
 
 #ifdef CONFIG_USB_SUSPEND
 
+/* Internal routine to adjust a device's usage counter and change
+ * its autosuspend state.
+ */
+static int usb_autopm_do_device(struct usb_device *udev, int inc_usage_cnt)
+{
+	int	status = 0;
+
+	usb_pm_lock(udev);
+	udev->pm_usage_cnt += inc_usage_cnt;
+	WARN_ON(udev->pm_usage_cnt < 0);
+	if (inc_usage_cnt >= 0 && udev->pm_usage_cnt > 0) {
+		udev->auto_pm = 1;
+		status = usb_resume_both(udev);
+		if (status != 0)
+			udev->pm_usage_cnt -= inc_usage_cnt;
+	} else if (inc_usage_cnt <= 0 && autosuspend_check(udev) == 0)
+		queue_delayed_work(ksuspend_usb_wq, &udev->autosuspend,
+				USB_AUTOSUSPEND_DELAY);
+	usb_pm_unlock(udev);
+	return status;
+}
+
 /**
  * usb_autosuspend_device - delayed autosuspend of a USB device and its interfaces
  * @udev: the usb_device to autosuspend
- * @dec_usage_cnt: flag to decrement @udev's PM-usage counter
  *
  * This routine should be called when a core subsystem is finished using
  * @udev and wants to allow it to autosuspend.  Examples would be when
  * @udev's device file in usbfs is closed or after a configuration change.
  *
- * @dec_usage_cnt should be 1 if the subsystem previously incremented
- * @udev's usage counter (such as by passing 1 to usb_autoresume_device);
- * otherwise it should be 0.
- *
- * If the usage counter for @udev or any of its active interfaces is greater
- * than 0, the autosuspend request will not be queued.  (If an interface
- * driver does not support autosuspend then its usage counter is permanently
- * positive.)  Likewise, if an interface driver requires remote-wakeup
- * capability during autosuspend but remote wakeup is disabled, the
- * autosuspend will fail.
+ * @udev's usage counter is decremented.  If it or any of the usage counters
+ * for an active interface is greater than 0, no autosuspend request will be
+ * queued.  (If an interface driver does not support autosuspend then its
+ * usage counter is permanently positive.)  Furthermore, if an interface
+ * driver requires remote-wakeup capability during autosuspend but remote
+ * wakeup is disabled, the autosuspend will fail.
  *
  * Often the caller will hold @udev's device lock, but this is not
  * necessary.
  *
  * This routine can run only in process context.
  */
-void usb_autosuspend_device(struct usb_device *udev, int dec_usage_cnt)
+void usb_autosuspend_device(struct usb_device *udev)
 {
-	usb_pm_lock(udev);
-	udev->pm_usage_cnt -= dec_usage_cnt;
-	if (udev->pm_usage_cnt <= 0)
-		queue_delayed_work(ksuspend_usb_wq, &udev->autosuspend,
-				USB_AUTOSUSPEND_DELAY);
-	usb_pm_unlock(udev);
+	int	status;
+
+	status = usb_autopm_do_device(udev, -1);
 	// dev_dbg(&udev->dev, "%s: cnt %d\n",
 	//		__FUNCTION__, udev->pm_usage_cnt);
 }
@@ -1142,44 +1208,59 @@
 /**
  * usb_autoresume_device - immediately autoresume a USB device and its interfaces
  * @udev: the usb_device to autoresume
- * @inc_usage_cnt: flag to increment @udev's PM-usage counter
  *
  * This routine should be called when a core subsystem wants to use @udev
- * and needs to guarantee that it is not suspended.  In addition, the
- * caller can prevent @udev from being autosuspended subsequently.  (Note
- * that this will not prevent suspend events originating in the PM core.)
- * Examples would be when @udev's device file in usbfs is opened (autosuspend
- * should be prevented until the file is closed) or when a remote-wakeup
- * request is received (later autosuspends should not be prevented).
+ * and needs to guarantee that it is not suspended.  No autosuspend will
+ * occur until usb_autosuspend_device is called.  (Note that this will not
+ * prevent suspend events originating in the PM core.)  Examples would be
+ * when @udev's device file in usbfs is opened or when a remote-wakeup
+ * request is received.
  *
- * @inc_usage_cnt should be 1 to increment @udev's usage counter and prevent
- * autosuspends.  This prevention will persist until the usage counter is
- * decremented again (such as by passing 1 to usb_autosuspend_device).
- * Otherwise @inc_usage_cnt should be 0 to leave the usage counter unchanged.
- * Regardless, if the autoresume fails then the usage counter is not
- * incremented.
+ * @udev's usage counter is incremented to prevent subsequent autosuspends.
+ * However if the autoresume fails then the usage counter is re-decremented.
  *
  * Often the caller will hold @udev's device lock, but this is not
  * necessary (and attempting it might cause deadlock).
  *
  * This routine can run only in process context.
  */
-int usb_autoresume_device(struct usb_device *udev, int inc_usage_cnt)
+int usb_autoresume_device(struct usb_device *udev)
 {
 	int	status;
 
-	usb_pm_lock(udev);
-	udev->pm_usage_cnt += inc_usage_cnt;
-	udev->auto_pm = 1;
-	status = usb_resume_both(udev);
-	if (status != 0)
-		udev->pm_usage_cnt -= inc_usage_cnt;
-	usb_pm_unlock(udev);
+	status = usb_autopm_do_device(udev, 1);
 	// dev_dbg(&udev->dev, "%s: status %d cnt %d\n",
 	//		__FUNCTION__, status, udev->pm_usage_cnt);
 	return status;
 }
 
+/* Internal routine to adjust an interface's usage counter and change
+ * its device's autosuspend state.
+ */
+static int usb_autopm_do_interface(struct usb_interface *intf,
+		int inc_usage_cnt)
+{
+	struct usb_device	*udev = interface_to_usbdev(intf);
+	int			status = 0;
+
+	usb_pm_lock(udev);
+	if (intf->condition == USB_INTERFACE_UNBOUND)
+		status = -ENODEV;
+	else {
+		intf->pm_usage_cnt += inc_usage_cnt;
+		if (inc_usage_cnt >= 0 && intf->pm_usage_cnt > 0) {
+			udev->auto_pm = 1;
+			status = usb_resume_both(udev);
+			if (status != 0)
+				intf->pm_usage_cnt -= inc_usage_cnt;
+		} else if (inc_usage_cnt <= 0 && autosuspend_check(udev) == 0)
+			queue_delayed_work(ksuspend_usb_wq, &udev->autosuspend,
+					USB_AUTOSUSPEND_DELAY);
+	}
+	usb_pm_unlock(udev);
+	return status;
+}
+
 /**
  * usb_autopm_put_interface - decrement a USB interface's PM-usage counter
  * @intf: the usb_interface whose counter should be decremented
@@ -1213,17 +1294,11 @@
  */
 void usb_autopm_put_interface(struct usb_interface *intf)
 {
-	struct usb_device	*udev = interface_to_usbdev(intf);
+	int	status;
 
-	usb_pm_lock(udev);
-	if (intf->condition != USB_INTERFACE_UNBOUND &&
-			--intf->pm_usage_cnt <= 0) {
-		queue_delayed_work(ksuspend_usb_wq, &udev->autosuspend,
-				USB_AUTOSUSPEND_DELAY);
-	}
-	usb_pm_unlock(udev);
-	// dev_dbg(&intf->dev, "%s: cnt %d\n",
-	//		__FUNCTION__, intf->pm_usage_cnt);
+	status = usb_autopm_do_interface(intf, -1);
+	// dev_dbg(&intf->dev, "%s: status %d cnt %d\n",
+	//		__FUNCTION__, status, intf->pm_usage_cnt);
 }
 EXPORT_SYMBOL_GPL(usb_autopm_put_interface);
 
@@ -1260,26 +1335,37 @@
  */
 int usb_autopm_get_interface(struct usb_interface *intf)
 {
-	struct usb_device	*udev = interface_to_usbdev(intf);
-	int			status;
+	int	status;
 
-	usb_pm_lock(udev);
-	if (intf->condition == USB_INTERFACE_UNBOUND)
-		status = -ENODEV;
-	else {
-		++intf->pm_usage_cnt;
-		udev->auto_pm = 1;
-		status = usb_resume_both(udev);
-		if (status != 0)
-			--intf->pm_usage_cnt;
-	}
-	usb_pm_unlock(udev);
+	status = usb_autopm_do_interface(intf, 1);
 	// dev_dbg(&intf->dev, "%s: status %d cnt %d\n",
 	//		__FUNCTION__, status, intf->pm_usage_cnt);
 	return status;
 }
 EXPORT_SYMBOL_GPL(usb_autopm_get_interface);
 
+/**
+ * usb_autopm_set_interface - set a USB interface's autosuspend state
+ * @intf: the usb_interface whose state should be set
+ *
+ * This routine sets the autosuspend state of @intf's device according
+ * to @intf's usage counter, which the caller must have set previously.
+ * If the counter is <= 0, the device is autosuspended (if it isn't
+ * already suspended and if nothing else prevents the autosuspend).  If
+ * the counter is > 0, the device is autoresumed (if it isn't already
+ * awake).
+ */
+int usb_autopm_set_interface(struct usb_interface *intf)
+{
+	int	status;
+
+	status = usb_autopm_do_interface(intf, 0);
+	// dev_dbg(&intf->dev, "%s: status %d cnt %d\n",
+	//		__FUNCTION__, status, intf->pm_usage_cnt);
+	return status;
+}
+EXPORT_SYMBOL_GPL(usb_autopm_set_interface);
+
 #endif /* CONFIG_USB_SUSPEND */
 
 static int usb_suspend(struct device *dev, pm_message_t message)
diff --git a/drivers/usb/core/endpoint.c b/drivers/usb/core/endpoint.c
index 3b2d137..c505b76 100644
--- a/drivers/usb/core/endpoint.c
+++ b/drivers/usb/core/endpoint.c
@@ -10,15 +10,20 @@
  */
 
 #include <linux/kernel.h>
+#include <linux/spinlock.h>
+#include <linux/idr.h>
 #include <linux/usb.h>
 #include "usb.h"
 
-/* endpoint stuff */
+#define MAX_ENDPOINT_MINORS (64*128*32)
+static int usb_endpoint_major;
+static DEFINE_IDR(endpoint_idr);
 
 struct ep_device {
 	struct usb_endpoint_descriptor *desc;
 	struct usb_device *udev;
 	struct device dev;
+	int minor;
 };
 #define to_ep_device(_dev) \
 	container_of(_dev, struct ep_device, dev)
@@ -152,6 +157,55 @@
 	.attrs = ep_dev_attrs,
 };
 
+static int usb_endpoint_major_init(void)
+{
+	dev_t dev;
+	int error;
+
+	error = alloc_chrdev_region(&dev, 0, MAX_ENDPOINT_MINORS,
+				    "usb_endpoint");
+	if (error) {
+		err("unable to get a dynamic major for usb endpoints");
+		return error;
+	}
+	usb_endpoint_major = MAJOR(dev);
+
+	return error;
+}
+
+static void usb_endpoint_major_cleanup(void)
+{
+	unregister_chrdev_region(MKDEV(usb_endpoint_major, 0),
+				 MAX_ENDPOINT_MINORS);
+}
+
+static int endpoint_get_minor(struct ep_device *ep_dev)
+{
+	static DEFINE_MUTEX(minor_lock);
+	int retval = -ENOMEM;
+	int id;
+
+	mutex_lock(&minor_lock);
+	if (idr_pre_get(&endpoint_idr, GFP_KERNEL) == 0)
+		goto exit;
+
+	retval = idr_get_new(&endpoint_idr, ep_dev, &id);
+	if (retval < 0) {
+		if (retval == -EAGAIN)
+			retval = -ENOMEM;
+		goto exit;
+	}
+	ep_dev->minor = id & MAX_ID_MASK;
+exit:
+	mutex_unlock(&minor_lock);
+	return retval;
+}
+
+static void endpoint_free_minor(struct ep_device *ep_dev)
+{
+	idr_remove(&endpoint_idr, ep_dev->minor);
+}
+
 static struct endpoint_class {
 	struct kref kref;
 	struct class *class;
@@ -176,11 +230,20 @@
 	ep_class->class = class_create(THIS_MODULE, "usb_endpoint");
 	if (IS_ERR(ep_class->class)) {
 		result = IS_ERR(ep_class->class);
-		kfree(ep_class);
-		ep_class = NULL;
-		goto exit;
+		goto class_create_error;
 	}
 
+	result = usb_endpoint_major_init();
+	if (result)
+		goto endpoint_major_error;
+
+	goto exit;
+
+endpoint_major_error:
+	class_destroy(ep_class->class);
+class_create_error:
+	kfree(ep_class);
+	ep_class = NULL;
 exit:
 	return result;
 }
@@ -191,6 +254,7 @@
 	class_destroy(ep_class->class);
 	kfree(ep_class);
 	ep_class = NULL;
+	usb_endpoint_major_cleanup();
 }
 
 static void destroy_endpoint_class(void)
@@ -213,7 +277,6 @@
 {
 	char name[8];
 	struct ep_device *ep_dev;
-	int minor;
 	int retval;
 
 	retval = init_endpoint_class();
@@ -226,12 +289,16 @@
 		goto error_alloc;
 	}
 
-	/* fun calculation to determine the minor of this endpoint */
-	minor = (((udev->bus->busnum - 1) * 128) * 16) + (udev->devnum - 1);
+	retval = endpoint_get_minor(ep_dev);
+	if (retval) {
+		dev_err(parent, "can not allocate minor number for %s",
+			ep_dev->dev.bus_id);
+		goto error_register;
+	}
 
 	ep_dev->desc = &endpoint->desc;
 	ep_dev->udev = udev;
-	ep_dev->dev.devt = MKDEV(442, minor);	// FIXME fake number...
+	ep_dev->dev.devt = MKDEV(usb_endpoint_major, ep_dev->minor);
 	ep_dev->dev.class = ep_class->class;
 	ep_dev->dev.parent = parent;
 	ep_dev->dev.release = ep_device_release;
@@ -241,7 +308,7 @@
 
 	retval = device_register(&ep_dev->dev);
 	if (retval)
-		goto error_register;
+		goto error_chrdev;
 	retval = sysfs_create_group(&ep_dev->dev.kobj, &ep_dev_attr_grp);
 	if (retval)
 		goto error_group;
@@ -261,6 +328,9 @@
 	destroy_endpoint_class();
 	return retval;
 
+error_chrdev:
+	endpoint_free_minor(ep_dev);
+
 error_register:
 	kfree(ep_dev);
 error_alloc:
@@ -271,14 +341,16 @@
 
 void usb_remove_ep_files(struct usb_host_endpoint *endpoint)
 {
+	struct ep_device *ep_dev = endpoint->ep_dev;
 
-	if (endpoint->ep_dev) {
+	if (ep_dev) {
 		char name[8];
 
 		sprintf(name, "ep_%02x", endpoint->desc.bEndpointAddress);
-		sysfs_remove_link(&endpoint->ep_dev->dev.parent->kobj, name);
-		sysfs_remove_group(&endpoint->ep_dev->dev.kobj, &ep_dev_attr_grp);
-		device_unregister(&endpoint->ep_dev->dev);
+		sysfs_remove_link(&ep_dev->dev.parent->kobj, name);
+		sysfs_remove_group(&ep_dev->dev.kobj, &ep_dev_attr_grp);
+		endpoint_free_minor(ep_dev);
+		device_unregister(&ep_dev->dev);
 		endpoint->ep_dev = NULL;
 		destroy_endpoint_class();
 	}
diff --git a/drivers/usb/core/hcd.c b/drivers/usb/core/hcd.c
index afa2dd2..10064af 100644
--- a/drivers/usb/core/hcd.c
+++ b/drivers/usb/core/hcd.c
@@ -256,7 +256,9 @@
 	0x05,       /*  __u8  ep_bDescriptorType; Endpoint */
 	0x81,       /*  __u8  ep_bEndpointAddress; IN Endpoint 1 */
  	0x03,       /*  __u8  ep_bmAttributes; Interrupt */
- 	0x02, 0x00, /*  __le16 ep_wMaxPacketSize; 1 + (MAX_ROOT_PORTS / 8) */
+		    /* __le16 ep_wMaxPacketSize; 1 + (MAX_ROOT_PORTS / 8)
+		     * see hub.c:hub_configure() for details. */
+	(USB_MAXCHILDREN + 1 + 7) / 8, 0x00,
 	0x0c        /*  __u8  ep_bInterval; (256ms -- usb 2.0 spec) */
 };
 
diff --git a/drivers/usb/core/hub.c b/drivers/usb/core/hub.c
index ba165af..0ce393e 100644
--- a/drivers/usb/core/hub.c
+++ b/drivers/usb/core/hub.c
@@ -31,6 +31,47 @@
 #include "hcd.h"
 #include "hub.h"
 
+struct usb_hub {
+	struct device		*intfdev;	/* the "interface" device */
+	struct usb_device	*hdev;
+	struct urb		*urb;		/* for interrupt polling pipe */
+
+	/* buffer for urb ... with extra space in case of babble */
+	char			(*buffer)[8];
+	dma_addr_t		buffer_dma;	/* DMA address for buffer */
+	union {
+		struct usb_hub_status	hub;
+		struct usb_port_status	port;
+	}			*status;	/* buffer for status reports */
+
+	int			error;		/* last reported error */
+	int			nerrors;	/* track consecutive errors */
+
+	struct list_head	event_list;	/* hubs w/data or errs ready */
+	unsigned long		event_bits[1];	/* status change bitmask */
+	unsigned long		change_bits[1];	/* ports with logical connect
+							status change */
+	unsigned long		busy_bits[1];	/* ports being reset or
+							resumed */
+#if USB_MAXCHILDREN > 31 /* 8*sizeof(unsigned long) - 1 */
+#error event_bits[] is too short!
+#endif
+
+	struct usb_hub_descriptor *descriptor;	/* class descriptor */
+	struct usb_tt		tt;		/* Transaction Translator */
+
+	unsigned		mA_per_port;	/* current for each child */
+
+	unsigned		limited_power:1;
+	unsigned		quiescing:1;
+	unsigned		activating:1;
+
+	unsigned		has_indicators:1;
+	u8			indicator[USB_MAXCHILDREN];
+	struct work_struct	leds;
+};
+
+
 /* Protect struct usb_device->state and ->children members
  * Note: Both are also protected by ->dev.sem, except that ->state can
  * change to USB_STATE_NOTATTACHED even when the semaphore isn't held. */
@@ -45,6 +86,16 @@
 
 static struct task_struct *khubd_task;
 
+/* multithreaded probe logic */
+static int multithread_probe =
+#ifdef CONFIG_USB_MULTITHREAD_PROBE
+	1;
+#else
+	0;
+#endif
+module_param(multithread_probe, bool, S_IRUGO);
+MODULE_PARM_DESC(multithread_probe, "Run each USB device probe in a new thread");
+
 /* cycle leds on hubs that aren't blinking for attention */
 static int blinkenlights = 0;
 module_param (blinkenlights, bool, S_IRUGO);
@@ -276,6 +327,9 @@
 {
 	unsigned long	flags;
 
+	/* Suppress autosuspend until khubd runs */
+	to_usb_interface(hub->intfdev)->pm_usage_cnt = 1;
+
 	spin_lock_irqsave(&hub_event_lock, flags);
 	if (list_empty(&hub->event_list)) {
 		list_add_tail(&hub->event_list, &hub_event_list);
@@ -457,7 +511,6 @@
 	/* (nonblocking) khubd and related activity won't re-trigger */
 	hub->quiescing = 1;
 	hub->activating = 0;
-	hub->resume_root_hub = 0;
 
 	/* (blocking) stop khubd and related activity */
 	usb_kill_urb(hub->urb);
@@ -473,7 +526,7 @@
 
 	hub->quiescing = 0;
 	hub->activating = 1;
-	hub->resume_root_hub = 0;
+
 	status = usb_submit_urb(hub->urb, GFP_NOIO);
 	if (status < 0)
 		dev_err(hub->intfdev, "activate --> %d\n", status);
@@ -759,7 +812,12 @@
 		dev_dbg(hub_dev, "%sover-current condition exists\n",
 			(hubstatus & HUB_STATUS_OVERCURRENT) ? "" : "no ");
 
-	/* set up the interrupt endpoint */
+	/* set up the interrupt endpoint
+	 * We use the EP's maxpacket size instead of (PORTS+1+7)/8
+	 * bytes as USB2.0[11.12.3] says because some hubs are known
+	 * to send more data (and thus cause overflow). For root hubs,
+	 * maxpktsize is defined in hcd.c's fake endpoint descriptors
+	 * to be big enough for at least USB_MAXCHILDREN ports. */
 	pipe = usb_rcvintpipe(hdev, endpoint->bEndpointAddress);
 	maxp = usb_maxpacket(hdev, pipe, usb_pipeout(pipe));
 
@@ -883,6 +941,7 @@
 	INIT_WORK(&hub->leds, led_work, hub);
 
 	usb_set_intfdata (intf, hub);
+	intf->needs_remote_wakeup = 1;
 
 	if (hdev->speed == USB_SPEED_HIGH)
 		highspeed_hubs++;
@@ -980,6 +1039,8 @@
 		if (udev->children[i])
 			recursively_mark_NOTATTACHED(udev->children[i]);
 	}
+	if (udev->state == USB_STATE_SUSPENDED)
+		udev->discon_suspended = 1;
 	udev->state = USB_STATE_NOTATTACHED;
 }
 
@@ -1169,6 +1230,14 @@
 	*pdev = NULL;
 	spin_unlock_irq(&device_state_lock);
 
+	/* Decrement the parent's count of unsuspended children */
+	if (udev->parent) {
+		usb_pm_lock(udev);
+		if (!udev->discon_suspended)
+			usb_autosuspend_device(udev->parent);
+		usb_pm_unlock(udev);
+	}
+
 	put_device(&udev->dev);
 }
 
@@ -1191,29 +1260,17 @@
 static int __usb_port_suspend(struct usb_device *, int port1);
 #endif
 
-/**
- * usb_new_device - perform initial device setup (usbcore-internal)
- * @udev: newly addressed device (in ADDRESS state)
- *
- * This is called with devices which have been enumerated, but not yet
- * configured.  The device descriptor is available, but not descriptors
- * for any device configuration.  The caller must have locked either
- * the parent hub (if udev is a normal device) or else the
- * usb_bus_list_lock (if udev is a root hub).  The parent's pointer to
- * udev has already been installed, but udev is not yet visible through
- * sysfs or other filesystem code.
- *
- * Returns 0 for success (device is configured and listed, with its
- * interfaces, in sysfs); else a negative errno value.
- *
- * This call is synchronous, and may not be used in an interrupt context.
- *
- * Only the hub driver or root-hub registrar should ever call this.
- */
-int usb_new_device(struct usb_device *udev)
+static int __usb_new_device(void *void_data)
 {
+	struct usb_device *udev = void_data;
 	int err;
 
+	/* Lock ourself into memory in order to keep a probe sequence
+	 * sleeping in a new thread from allowing us to be unloaded.
+	 */
+	if (!try_module_get(THIS_MODULE))
+		return -EINVAL;
+
 	err = usb_get_configuration(udev);
 	if (err < 0) {
 		dev_err(&udev->dev, "can't read configurations, error %d\n",
@@ -1309,13 +1366,56 @@
 		goto fail;
 	}
 
-	return 0;
+	/* Increment the parent's count of unsuspended children */
+	if (udev->parent)
+		usb_autoresume_device(udev->parent);
+
+exit:
+	module_put(THIS_MODULE);
+	return err;
 
 fail:
 	usb_set_device_state(udev, USB_STATE_NOTATTACHED);
-	return err;
+	goto exit;
 }
 
+/**
+ * usb_new_device - perform initial device setup (usbcore-internal)
+ * @udev: newly addressed device (in ADDRESS state)
+ *
+ * This is called with devices which have been enumerated, but not yet
+ * configured.  The device descriptor is available, but not descriptors
+ * for any device configuration.  The caller must have locked either
+ * the parent hub (if udev is a normal device) or else the
+ * usb_bus_list_lock (if udev is a root hub).  The parent's pointer to
+ * udev has already been installed, but udev is not yet visible through
+ * sysfs or other filesystem code.
+ *
+ * The return value for this function depends on if the
+ * multithread_probe variable is set or not.  If it's set, it will
+ * return a if the probe thread was successfully created or not.  If the
+ * variable is not set, it will return if the device is configured
+ * properly or not.  interfaces, in sysfs); else a negative errno value.
+ *
+ * This call is synchronous, and may not be used in an interrupt context.
+ *
+ * Only the hub driver or root-hub registrar should ever call this.
+ */
+int usb_new_device(struct usb_device *udev)
+{
+	struct task_struct *probe_task;
+	int ret = 0;
+
+	if (multithread_probe) {
+		probe_task = kthread_run(__usb_new_device, udev,
+					 "usb-probe-%s", udev->devnum);
+		if (IS_ERR(probe_task))
+			ret = PTR_ERR(probe_task);
+	} else
+		ret = __usb_new_device(udev);
+
+	return ret;
+}
 
 static int hub_port_status(struct usb_hub *hub, int port1,
 			       u16 *status, u16 *change)
@@ -1323,10 +1423,12 @@
 	int ret;
 
 	ret = get_port_status(hub->hdev, port1, &hub->status->port);
-	if (ret < 0)
+	if (ret < 4) {
 		dev_err (hub->intfdev,
 			"%s failed (err = %d)\n", __FUNCTION__, ret);
-	else {
+		if (ret >= 0)
+			ret = -EIO;
+	} else {
 		*status = le16_to_cpu(hub->status->port.wPortStatus);
 		*change = le16_to_cpu(hub->status->port.wPortChange); 
 		ret = 0;
@@ -1674,6 +1776,12 @@
 hub_port_resume(struct usb_hub *hub, int port1, struct usb_device *udev)
 {
 	int	status;
+	u16	portchange, portstatus;
+
+	/* Skip the initial Clear-Suspend step for a remote wakeup */
+	status = hub_port_status(hub, port1, &portstatus, &portchange);
+	if (status == 0 && !(portstatus & USB_PORT_STAT_SUSPEND))
+		goto SuspendCleared;
 
 	// dev_dbg(hub->intfdev, "resume port %d\n", port1);
 
@@ -1687,9 +1795,6 @@
 			"can't resume port %d, status %d\n",
 			port1, status);
 	} else {
-		u16		devstatus;
-		u16		portchange;
-
 		/* drive resume for at least 20 msec */
 		if (udev)
 			dev_dbg(&udev->dev, "usb %sresume\n",
@@ -1704,16 +1809,15 @@
 		 * stop resume signaling.  Then finish the resume
 		 * sequence.
 		 */
-		devstatus = portchange = 0;
-		status = hub_port_status(hub, port1,
-				&devstatus, &portchange);
+		status = hub_port_status(hub, port1, &portstatus, &portchange);
+SuspendCleared:
 		if (status < 0
-				|| (devstatus & LIVE_FLAGS) != LIVE_FLAGS
-				|| (devstatus & USB_PORT_STAT_SUSPEND) != 0
+				|| (portstatus & LIVE_FLAGS) != LIVE_FLAGS
+				|| (portstatus & USB_PORT_STAT_SUSPEND) != 0
 				) {
 			dev_dbg(hub->intfdev,
 				"port %d status %04x.%04x after resume, %d\n",
-				port1, portchange, devstatus, status);
+				port1, portchange, portstatus, status);
 			if (status >= 0)
 				status = -ENODEV;
 		} else {
@@ -1774,23 +1878,16 @@
 {
 	int	status = 0;
 
-	/* All this just to avoid sending a port-resume message
-	 * to the parent hub! */
-
 	usb_lock_device(udev);
-	usb_pm_lock(udev);
 	if (udev->state == USB_STATE_SUSPENDED) {
 		dev_dbg(&udev->dev, "usb %sresume\n", "wakeup-");
-		/* TRSMRCY = 10 msec */
-		msleep(10);
-		status = finish_port_resume(udev);
-		if (status == 0)
-			udev->dev.power.power_state.event = PM_EVENT_ON;
-	}
-	usb_pm_unlock(udev);
+		status = usb_autoresume_device(udev);
 
-	if (status == 0)
-		usb_autoresume_device(udev, 0);
+		/* Give the interface drivers a chance to do something,
+		 * then autosuspend the device again. */
+		if (status == 0)
+			usb_autosuspend_device(udev);
+	}
 	usb_unlock_device(udev);
 	return status;
 }
@@ -1854,6 +1951,8 @@
 		}
 	}
 
+	dev_dbg(&intf->dev, "%s\n", __FUNCTION__);
+
 	/* "global suspend" of the downstream HC-to-USB interface */
 	if (!hdev->parent) {
 		struct usb_bus	*bus = hdev->bus;
@@ -1876,10 +1975,12 @@
 
 static int hub_resume(struct usb_interface *intf)
 {
-	struct usb_device	*hdev = interface_to_usbdev(intf);
 	struct usb_hub		*hub = usb_get_intfdata (intf);
+	struct usb_device	*hdev = hub->hdev;
 	int			status;
 
+	dev_dbg(&intf->dev, "%s\n", __FUNCTION__);
+
 	/* "global resume" of the downstream HC-to-USB interface */
 	if (!hdev->parent) {
 		struct usb_bus	*bus = hdev->bus;
@@ -1918,7 +2019,6 @@
 {
 	struct usb_hub *hub = hdev_to_hub(hdev);
 
-	hub->resume_root_hub = 1;
 	kick_khubd(hub);
 }
 
@@ -2555,16 +2655,13 @@
 		intf = to_usb_interface(hub->intfdev);
 		hub_dev = &intf->dev;
 
-		i = hub->resume_root_hub;
-
-		dev_dbg(hub_dev, "state %d ports %d chg %04x evt %04x%s\n",
+		dev_dbg(hub_dev, "state %d ports %d chg %04x evt %04x\n",
 				hdev->state, hub->descriptor
 					? hub->descriptor->bNbrPorts
 					: 0,
 				/* NOTE: expects max 15 ports... */
 				(u16) hub->change_bits[0],
-				(u16) hub->event_bits[0],
-				i ? ", resume root" : "");
+				(u16) hub->event_bits[0]);
 
 		usb_get_intf(intf);
 		spin_unlock_irq(&hub_event_lock);
@@ -2585,16 +2682,16 @@
 			goto loop;
 		}
 
-		/* Is this is a root hub wanting to reactivate the downstream
-		 * ports?  If so, be sure the interface resumes even if its
-		 * stub "device" node was never suspended.
-		 */
-		if (i)
-			usb_autoresume_device(hdev, 0);
-
-		/* If this is an inactive or suspended hub, do nothing */
-		if (hub->quiescing)
+		/* Autoresume */
+		ret = usb_autopm_get_interface(intf);
+		if (ret) {
+			dev_dbg(hub_dev, "Can't autoresume: %d\n", ret);
 			goto loop;
+		}
+
+		/* If this is an inactive hub, do nothing */
+		if (hub->quiescing)
+			goto loop_autopm;
 
 		if (hub->error) {
 			dev_dbg (hub_dev, "resetting for error %d\n",
@@ -2604,7 +2701,7 @@
 			if (ret) {
 				dev_dbg (hub_dev,
 					"error resetting hub: %d\n", ret);
-				goto loop;
+				goto loop_autopm;
 			}
 
 			hub->nerrors = 0;
@@ -2732,6 +2829,10 @@
 		if (!hdev->parent && !hub->busy_bits[0])
 			usb_enable_root_hub_irq(hdev->bus);
 
+loop_autopm:
+		/* Allow autosuspend if we're not going to run again */
+		if (list_empty(&hub->event_list))
+			usb_autopm_enable(intf);
 loop:
 		usb_unlock_device(hdev);
 		usb_put_intf(intf);
@@ -2773,6 +2874,7 @@
 	.post_reset =	hub_post_reset,
 	.ioctl =	hub_ioctl,
 	.id_table =	hub_id_table,
+	.supports_autosuspend =	1,
 };
 
 int usb_hub_init(void)
@@ -2997,7 +3099,7 @@
 	}
 
 	/* Prevent autosuspend during the reset */
-	usb_autoresume_device(udev, 1);
+	usb_autoresume_device(udev);
 
 	if (iface && iface->condition != USB_INTERFACE_BINDING)
 		iface = NULL;
@@ -3040,7 +3142,7 @@
 		}
 	}
 
-	usb_autosuspend_device(udev, 1);
+	usb_autosuspend_device(udev);
 	return ret;
 }
 EXPORT_SYMBOL(usb_reset_composite_device);
diff --git a/drivers/usb/core/hub.h b/drivers/usb/core/hub.h
index 0f8e82a..cf9559c 100644
--- a/drivers/usb/core/hub.h
+++ b/drivers/usb/core/hub.h
@@ -192,45 +192,4 @@
 
 extern void usb_hub_tt_clear_buffer (struct usb_device *dev, int pipe);
 
-struct usb_hub {
-	struct device		*intfdev;	/* the "interface" device */
-	struct usb_device	*hdev;
-	struct urb		*urb;		/* for interrupt polling pipe */
-
-	/* buffer for urb ... with extra space in case of babble */
-	char			(*buffer)[8];
-	dma_addr_t		buffer_dma;	/* DMA address for buffer */
-	union {
-		struct usb_hub_status	hub;
-		struct usb_port_status	port;
-	}			*status;	/* buffer for status reports */
-
-	int			error;		/* last reported error */
-	int			nerrors;	/* track consecutive errors */
-
-	struct list_head	event_list;	/* hubs w/data or errs ready */
-	unsigned long		event_bits[1];	/* status change bitmask */
-	unsigned long		change_bits[1];	/* ports with logical connect
-							status change */
-	unsigned long		busy_bits[1];	/* ports being reset or
-							resumed */
-#if USB_MAXCHILDREN > 31 /* 8*sizeof(unsigned long) - 1 */
-#error event_bits[] is too short!
-#endif
-
-	struct usb_hub_descriptor *descriptor;	/* class descriptor */
-	struct usb_tt		tt;		/* Transaction Translator */
-
-	unsigned		mA_per_port;	/* current for each child */
-
-	unsigned		limited_power:1;
-	unsigned		quiescing:1;
-	unsigned		activating:1;
-	unsigned		resume_root_hub:1;
-
-	unsigned		has_indicators:1;
-	enum hub_led_mode	indicator[USB_MAXCHILDREN];
-	struct work_struct	leds;
-};
-
 #endif /* __LINUX_HUB_H */
diff --git a/drivers/usb/core/message.c b/drivers/usb/core/message.c
index 7729c07..29b0fa9 100644
--- a/drivers/usb/core/message.c
+++ b/drivers/usb/core/message.c
@@ -764,7 +764,7 @@
 			err = -EINVAL;
 			goto errout;
 		} else {
-			dev->have_langid = -1;
+			dev->have_langid = 1;
 			dev->string_langid = tbuf[2] | (tbuf[3]<< 8);
 				/* always use the first langid listed */
 			dev_dbg (&dev->dev, "default language 0x%04x\n",
@@ -1398,7 +1398,7 @@
 	}
 
 	/* Wake up the device so we can send it the Set-Config request */
-	ret = usb_autoresume_device(dev, 1);
+	ret = usb_autoresume_device(dev);
 	if (ret)
 		goto free_interfaces;
 
@@ -1421,7 +1421,7 @@
 	dev->actconfig = cp;
 	if (!cp) {
 		usb_set_device_state(dev, USB_STATE_ADDRESS);
-		usb_autosuspend_device(dev, 1);
+		usb_autosuspend_device(dev);
 		goto free_interfaces;
 	}
 	usb_set_device_state(dev, USB_STATE_CONFIGURED);
@@ -1490,7 +1490,7 @@
 		usb_create_sysfs_intf_files (intf);
 	}
 
-	usb_autosuspend_device(dev, 1);
+	usb_autosuspend_device(dev);
 	return 0;
 }
 
diff --git a/drivers/usb/core/usb.c b/drivers/usb/core/usb.c
index 467cb02..81cb525 100644
--- a/drivers/usb/core/usb.c
+++ b/drivers/usb/core/usb.c
@@ -200,13 +200,6 @@
 	destroy_workqueue(ksuspend_usb_wq);
 }
 
-#else
-
-#define ksuspend_usb_init()	0
-#define ksuspend_usb_cleanup()	do {} while (0)
-
-#endif
-
 #ifdef	CONFIG_USB_SUSPEND
 
 /* usb_autosuspend_work - callback routine to autosuspend a USB device */
@@ -225,7 +218,14 @@
 static void usb_autosuspend_work(void *_udev)
 {}
 
-#endif
+#endif	/* CONFIG_USB_SUSPEND */
+
+#else
+
+#define ksuspend_usb_init()	0
+#define ksuspend_usb_cleanup()	do {} while (0)
+
+#endif	/* CONFIG_PM */
 
 /**
  * usb_alloc_dev - usb device constructor (usbcore-internal)
@@ -537,138 +537,6 @@
 	return usb_hcd_get_frame_number (dev);
 }
 
-/**
- * usb_endpoint_dir_in - check if the endpoint has IN direction
- * @epd: endpoint to be checked
- *
- * Returns true if the endpoint is of type IN, otherwise it returns false.
- */
-int usb_endpoint_dir_in(const struct usb_endpoint_descriptor *epd)
-{
-	return ((epd->bEndpointAddress & USB_ENDPOINT_DIR_MASK) == USB_DIR_IN);
-}
-
-/**
- * usb_endpoint_dir_out - check if the endpoint has OUT direction
- * @epd: endpoint to be checked
- *
- * Returns true if the endpoint is of type OUT, otherwise it returns false.
- */
-int usb_endpoint_dir_out(const struct usb_endpoint_descriptor *epd)
-{
-	return ((epd->bEndpointAddress & USB_ENDPOINT_DIR_MASK) == USB_DIR_OUT);
-}
-
-/**
- * usb_endpoint_xfer_bulk - check if the endpoint has bulk transfer type
- * @epd: endpoint to be checked
- *
- * Returns true if the endpoint is of type bulk, otherwise it returns false.
- */
-int usb_endpoint_xfer_bulk(const struct usb_endpoint_descriptor *epd)
-{
-	return ((epd->bmAttributes & USB_ENDPOINT_XFERTYPE_MASK) ==
-		USB_ENDPOINT_XFER_BULK);
-}
-
-/**
- * usb_endpoint_xfer_int - check if the endpoint has interrupt transfer type
- * @epd: endpoint to be checked
- *
- * Returns true if the endpoint is of type interrupt, otherwise it returns
- * false.
- */
-int usb_endpoint_xfer_int(const struct usb_endpoint_descriptor *epd)
-{
-	return ((epd->bmAttributes & USB_ENDPOINT_XFERTYPE_MASK) ==
-		USB_ENDPOINT_XFER_INT);
-}
-
-/**
- * usb_endpoint_xfer_isoc - check if the endpoint has isochronous transfer type
- * @epd: endpoint to be checked
- *
- * Returns true if the endpoint is of type isochronous, otherwise it returns
- * false.
- */
-int usb_endpoint_xfer_isoc(const struct usb_endpoint_descriptor *epd)
-{
-	return ((epd->bmAttributes & USB_ENDPOINT_XFERTYPE_MASK) ==
-		USB_ENDPOINT_XFER_ISOC);
-}
-
-/**
- * usb_endpoint_is_bulk_in - check if the endpoint is bulk IN
- * @epd: endpoint to be checked
- *
- * Returns true if the endpoint has bulk transfer type and IN direction,
- * otherwise it returns false.
- */
-int usb_endpoint_is_bulk_in(const struct usb_endpoint_descriptor *epd)
-{
-	return (usb_endpoint_xfer_bulk(epd) && usb_endpoint_dir_in(epd));
-}
-
-/**
- * usb_endpoint_is_bulk_out - check if the endpoint is bulk OUT
- * @epd: endpoint to be checked
- *
- * Returns true if the endpoint has bulk transfer type and OUT direction,
- * otherwise it returns false.
- */
-int usb_endpoint_is_bulk_out(const struct usb_endpoint_descriptor *epd)
-{
-	return (usb_endpoint_xfer_bulk(epd) && usb_endpoint_dir_out(epd));
-}
-
-/**
- * usb_endpoint_is_int_in - check if the endpoint is interrupt IN
- * @epd: endpoint to be checked
- *
- * Returns true if the endpoint has interrupt transfer type and IN direction,
- * otherwise it returns false.
- */
-int usb_endpoint_is_int_in(const struct usb_endpoint_descriptor *epd)
-{
-	return (usb_endpoint_xfer_int(epd) && usb_endpoint_dir_in(epd));
-}
-
-/**
- * usb_endpoint_is_int_out - check if the endpoint is interrupt OUT
- * @epd: endpoint to be checked
- *
- * Returns true if the endpoint has interrupt transfer type and OUT direction,
- * otherwise it returns false.
- */
-int usb_endpoint_is_int_out(const struct usb_endpoint_descriptor *epd)
-{
-	return (usb_endpoint_xfer_int(epd) && usb_endpoint_dir_out(epd));
-}
-
-/**
- * usb_endpoint_is_isoc_in - check if the endpoint is isochronous IN
- * @epd: endpoint to be checked
- *
- * Returns true if the endpoint has isochronous transfer type and IN direction,
- * otherwise it returns false.
- */
-int usb_endpoint_is_isoc_in(const struct usb_endpoint_descriptor *epd)
-{
-	return (usb_endpoint_xfer_isoc(epd) && usb_endpoint_dir_in(epd));
-}
-
-/**
- * usb_endpoint_is_isoc_out - check if the endpoint is isochronous OUT
- * @epd: endpoint to be checked
- *
- * Returns true if the endpoint has isochronous transfer type and OUT direction,
- * otherwise it returns false.
- */
-int usb_endpoint_is_isoc_out(const struct usb_endpoint_descriptor *epd)
-{
-	return (usb_endpoint_xfer_isoc(epd) && usb_endpoint_dir_out(epd));
-}
-
 /*-------------------------------------------------------------------*/
 /*
  * __usb_get_extra_descriptor() finds a descriptor of specific type in the
@@ -1102,18 +970,6 @@
 EXPORT_SYMBOL(usb_find_device);
 EXPORT_SYMBOL(usb_get_current_frame_number);
 
-EXPORT_SYMBOL_GPL(usb_endpoint_dir_in);
-EXPORT_SYMBOL_GPL(usb_endpoint_dir_out);
-EXPORT_SYMBOL_GPL(usb_endpoint_xfer_bulk);
-EXPORT_SYMBOL_GPL(usb_endpoint_xfer_int);
-EXPORT_SYMBOL_GPL(usb_endpoint_xfer_isoc);
-EXPORT_SYMBOL_GPL(usb_endpoint_is_bulk_in);
-EXPORT_SYMBOL_GPL(usb_endpoint_is_bulk_out);
-EXPORT_SYMBOL_GPL(usb_endpoint_is_int_in);
-EXPORT_SYMBOL_GPL(usb_endpoint_is_int_out);
-EXPORT_SYMBOL_GPL(usb_endpoint_is_isoc_in);
-EXPORT_SYMBOL_GPL(usb_endpoint_is_isoc_out);
-
 EXPORT_SYMBOL (usb_buffer_alloc);
 EXPORT_SYMBOL (usb_buffer_free);
 
diff --git a/drivers/usb/core/usb.h b/drivers/usb/core/usb.h
index 13322e3..17830a8 100644
--- a/drivers/usb/core/usb.h
+++ b/drivers/usb/core/usb.h
@@ -64,14 +64,13 @@
 
 #define USB_AUTOSUSPEND_DELAY	(HZ*2)
 
-extern void usb_autosuspend_device(struct usb_device *udev, int dec_busy_cnt);
-extern int usb_autoresume_device(struct usb_device *udev, int inc_busy_cnt);
+extern void usb_autosuspend_device(struct usb_device *udev);
+extern int usb_autoresume_device(struct usb_device *udev);
 
 #else
 
-#define usb_autosuspend_device(udev, dec_busy_cnt)	do {} while (0)
-static inline int usb_autoresume_device(struct usb_device *udev,
-		int inc_busy_cnt)
+#define usb_autosuspend_device(udev)	do {} while (0)
+static inline int usb_autoresume_device(struct usb_device *udev)
 {
 	return 0;
 }
diff --git a/drivers/usb/gadget/ether.c b/drivers/usb/gadget/ether.c
index 1c17d26..3bd1dfe 100644
--- a/drivers/usb/gadget/ether.c
+++ b/drivers/usb/gadget/ether.c
@@ -1894,13 +1894,13 @@
 	if (!eth_is_promisc (dev)) {
 		u8		*dest = skb->data;
 
-		if (dest [0] & 0x01) {
+		if (is_multicast_ether_addr(dest)) {
 			u16	type;
 
 			/* ignores USB_CDC_PACKET_TYPE_MULTICAST and host
 			 * SET_ETHERNET_MULTICAST_FILTERS requests
 			 */
-			if (memcmp (dest, net->broadcast, ETH_ALEN) == 0)
+			if (is_broadcast_ether_addr(dest))
 				type = USB_CDC_PACKET_TYPE_BROADCAST;
 			else
 				type = USB_CDC_PACKET_TYPE_ALL_MULTICAST;
diff --git a/drivers/usb/gadget/lh7a40x_udc.c b/drivers/usb/gadget/lh7a40x_udc.c
index 1792596..4a99156 100644
--- a/drivers/usb/gadget/lh7a40x_udc.c
+++ b/drivers/usb/gadget/lh7a40x_udc.c
@@ -83,7 +83,6 @@
 static int lh7a40x_dequeue(struct usb_ep *ep, struct usb_request *);
 static int lh7a40x_set_halt(struct usb_ep *ep, int);
 static int lh7a40x_fifo_status(struct usb_ep *ep);
-static int lh7a40x_fifo_status(struct usb_ep *ep);
 static void lh7a40x_fifo_flush(struct usb_ep *ep);
 static void lh7a40x_ep0_kick(struct lh7a40x_udc *dev, struct lh7a40x_ep *ep);
 static void lh7a40x_handle_ep0(struct lh7a40x_udc *dev, u32 intr);
diff --git a/drivers/usb/gadget/net2280.c b/drivers/usb/gadget/net2280.c
index 3acc896..0b59083 100644
--- a/drivers/usb/gadget/net2280.c
+++ b/drivers/usb/gadget/net2280.c
@@ -1040,6 +1040,7 @@
 
 	} /* else the irq handler advances the queue. */
 
+	ep->responded = 1;
 	if (req)
 		list_add_tail (&req->queue, &ep->queue);
 done:
@@ -2188,7 +2189,8 @@
 					ep->stopped = 1;
 					set_halt (ep);
 					mode = 2;
-				} else if (!req && !ep->stopped)
+				} else if (ep->responded &&
+						!req && !ep->stopped)
 					write_fifo (ep, NULL);
 			}
 		} else {
@@ -2203,7 +2205,7 @@
 			} else if (((t & (1 << DATA_OUT_PING_TOKEN_INTERRUPT))
 					&& req
 					&& req->req.actual == req->req.length)
-					|| !req) {
+					|| (ep->responded && !req)) {
 				ep->dev->protocol_stall = 1;
 				set_halt (ep);
 				ep->stopped = 1;
@@ -2469,6 +2471,7 @@
 		/* we made the hardware handle most lowlevel requests;
 		 * everything else goes uplevel to the gadget code.
 		 */
+		ep->responded = 1;
 		switch (u.r.bRequest) {
 		case USB_REQ_GET_STATUS: {
 			struct net2280_ep	*e;
@@ -2537,6 +2540,7 @@
 				u.r.bRequestType, u.r.bRequest,
 				w_value, w_index, w_length,
 				readl (&ep->regs->ep_cfg));
+			ep->responded = 0;
 			spin_unlock (&dev->lock);
 			tmp = dev->driver->setup (&dev->gadget, &u.r);
 			spin_lock (&dev->lock);
diff --git a/drivers/usb/gadget/net2280.h b/drivers/usb/gadget/net2280.h
index 957d6df..44ca139 100644
--- a/drivers/usb/gadget/net2280.h
+++ b/drivers/usb/gadget/net2280.h
@@ -110,7 +110,8 @@
 						out_overflow : 1,
 						stopped : 1,
 						is_in : 1,
-						is_iso : 1;
+						is_iso : 1,
+						responded : 1;
 };
 
 static inline void allow_status (struct net2280_ep *ep)
diff --git a/drivers/usb/gadget/pxa2xx_udc.c b/drivers/usb/gadget/pxa2xx_udc.c
index 671c24b..1ed506e 100644
--- a/drivers/usb/gadget/pxa2xx_udc.c
+++ b/drivers/usb/gadget/pxa2xx_udc.c
@@ -2472,6 +2472,7 @@
 #define PXA210_B1		0x00000123
 #define PXA210_B0		0x00000122
 #define IXP425_A0		0x000001c1
+#define IXP425_B0		0x000001f1
 #define IXP465_AD		0x00000200
 
 /*
@@ -2509,6 +2510,7 @@
 		break;
 #elif	defined(CONFIG_ARCH_IXP4XX)
 	case IXP425_A0:
+	case IXP425_B0:
 	case IXP465_AD:
 		dev->has_cfr = 1;
 		out_dma = 0;
diff --git a/drivers/usb/host/Kconfig b/drivers/usb/host/Kconfig
index cf10cbc..cc60759 100644
--- a/drivers/usb/host/Kconfig
+++ b/drivers/usb/host/Kconfig
@@ -153,7 +153,7 @@
 	  adapter will *NOT* work with PC cards that do not contain an OHCI
 	  controller.
 
-	  For those PC cards that contain multiple OHCI controllers only ther
+	  For those PC cards that contain multiple OHCI controllers only the
 	  first one is used.
 
 	  The driver consists of two modules, the "ftdi-elan" module is a
diff --git a/drivers/usb/host/ehci-hcd.c b/drivers/usb/host/ehci-hcd.c
index 9030994..025d333 100644
--- a/drivers/usb/host/ehci-hcd.c
+++ b/drivers/usb/host/ehci-hcd.c
@@ -126,6 +126,11 @@
 module_param (park, uint, S_IRUGO);
 MODULE_PARM_DESC (park, "park setting; 1-3 back-to-back async packets");
 
+/* for flakey hardware, ignore overcurrent indicators */
+static int ignore_oc = 0;
+module_param (ignore_oc, bool, S_IRUGO);
+MODULE_PARM_DESC (ignore_oc, "ignore bogus hardware overcurrent indications");
+
 #define	INTR_MASK (STS_IAA | STS_FATAL | STS_PCD | STS_ERR | STS_INT)
 
 /*-------------------------------------------------------------------------*/
@@ -541,9 +546,10 @@
 
 	temp = HC_VERSION(readl (&ehci->caps->hc_capbase));
 	ehci_info (ehci,
-		"USB %x.%x started, EHCI %x.%02x, driver %s\n",
+		"USB %x.%x started, EHCI %x.%02x, driver %s%s\n",
 		((ehci->sbrn & 0xf0)>>4), (ehci->sbrn & 0x0f),
-		temp >> 8, temp & 0xff, DRIVER_VERSION);
+		temp >> 8, temp & 0xff, DRIVER_VERSION,
+		ignore_oc ? ", overcurrent ignored" : "");
 
 	writel (INTR_MASK, &ehci->regs->intr_enable); /* Turn On Interrupts */
 
@@ -613,9 +619,8 @@
 		unsigned	i = HCS_N_PORTS (ehci->hcs_params);
 
 		/* resume root hub? */
-		status = readl (&ehci->regs->command);
-		if (!(status & CMD_RUN))
-			writel (status | CMD_RUN, &ehci->regs->command);
+		if (!(readl(&ehci->regs->command) & CMD_RUN))
+			usb_hcd_resume_root_hub(hcd);
 
 		while (i--) {
 			int pstatus = readl (&ehci->regs->port_status [i]);
@@ -632,7 +637,6 @@
 			 */
 			ehci->reset_done [i] = jiffies + msecs_to_jiffies (20);
 			ehci_dbg (ehci, "port %d remote wakeup\n", i + 1);
-			usb_hcd_resume_root_hub(hcd);
 		}
 	}
 
diff --git a/drivers/usb/host/ehci-hub.c b/drivers/usb/host/ehci-hub.c
index 1b20722..bfe5f30 100644
--- a/drivers/usb/host/ehci-hub.c
+++ b/drivers/usb/host/ehci-hub.c
@@ -34,6 +34,7 @@
 {
 	struct ehci_hcd		*ehci = hcd_to_ehci (hcd);
 	int			port;
+	int			mask;
 
 	if (time_before (jiffies, ehci->next_statechange))
 		msleep(5);
@@ -51,14 +52,25 @@
 		ehci->reclaim_ready = 1;
 	ehci_work(ehci);
 
-	/* suspend any active/unsuspended ports, maybe allow wakeup */
+	/* Unlike other USB host controller types, EHCI doesn't have
+	 * any notion of "global" or bus-wide suspend.  The driver has
+	 * to manually suspend all the active unsuspended ports, and
+	 * then manually resume them in the bus_resume() routine.
+	 */
+	ehci->bus_suspended = 0;
 	while (port--) {
 		u32 __iomem	*reg = &ehci->regs->port_status [port];
 		u32		t1 = readl (reg) & ~PORT_RWC_BITS;
 		u32		t2 = t1;
 
-		if ((t1 & PORT_PE) && !(t1 & PORT_OWNER))
+		/* keep track of which ports we suspend */
+		if ((t1 & PORT_PE) && !(t1 & PORT_OWNER) &&
+				!(t1 & PORT_SUSPEND)) {
 			t2 |= PORT_SUSPEND;
+			set_bit(port, &ehci->bus_suspended);
+		}
+
+		/* enable remote wakeup on all ports */
 		if (device_may_wakeup(&hcd->self.root_hub->dev))
 			t2 |= PORT_WKOC_E|PORT_WKDISC_E|PORT_WKCONN_E;
 		else
@@ -76,6 +88,13 @@
 	ehci_halt (ehci);
 	hcd->state = HC_STATE_SUSPENDED;
 
+	/* allow remote wakeup */
+	mask = INTR_MASK;
+	if (!device_may_wakeup(&hcd->self.root_hub->dev))
+		mask &= ~STS_PCD;
+	writel(mask, &ehci->regs->intr_enable);
+	readl(&ehci->regs->intr_enable);
+
 	ehci->next_statechange = jiffies + msecs_to_jiffies(10);
 	spin_unlock_irq (&ehci->lock);
 	return 0;
@@ -88,7 +107,6 @@
 	struct ehci_hcd		*ehci = hcd_to_ehci (hcd);
 	u32			temp;
 	int			i;
-	int			intr_enable;
 
 	if (time_before (jiffies, ehci->next_statechange))
 		msleep(5);
@@ -100,31 +118,30 @@
 	 * the last user of the controller, not reset/pm hardware keeping
 	 * state we gave to it.
 	 */
+	temp = readl(&ehci->regs->intr_enable);
+	ehci_dbg(ehci, "resume root hub%s\n", temp ? "" : " after power loss");
 
-	/* re-init operational registers in case we lost power */
-	if (readl (&ehci->regs->intr_enable) == 0) {
-		/* at least some APM implementations will try to deliver
-		 * IRQs right away, so delay them until we're ready.
-		 */
-		intr_enable = 1;
-		writel (0, &ehci->regs->segment);
-		writel (ehci->periodic_dma, &ehci->regs->frame_list);
-		writel ((u32)ehci->async->qh_dma, &ehci->regs->async_next);
-	} else
-		intr_enable = 0;
-	ehci_dbg(ehci, "resume root hub%s\n",
-			intr_enable ? " after power loss" : "");
+	/* at least some APM implementations will try to deliver
+	 * IRQs right away, so delay them until we're ready.
+	 */
+	writel(0, &ehci->regs->intr_enable);
+
+	/* re-init operational registers */
+	writel(0, &ehci->regs->segment);
+	writel(ehci->periodic_dma, &ehci->regs->frame_list);
+	writel((u32) ehci->async->qh_dma, &ehci->regs->async_next);
 
 	/* restore CMD_RUN, framelist size, and irq threshold */
 	writel (ehci->command, &ehci->regs->command);
 
-	/* take ports out of suspend */
+	/* manually resume the ports we suspended during bus_suspend() */
 	i = HCS_N_PORTS (ehci->hcs_params);
 	while (i--) {
 		temp = readl (&ehci->regs->port_status [i]);
 		temp &= ~(PORT_RWC_BITS
 			| PORT_WKOC_E | PORT_WKDISC_E | PORT_WKCONN_E);
-		if (temp & PORT_SUSPEND) {
+		if (test_bit(i, &ehci->bus_suspended) &&
+				(temp & PORT_SUSPEND)) {
 			ehci->reset_done [i] = jiffies + msecs_to_jiffies (20);
 			temp |= PORT_RESUME;
 		}
@@ -134,11 +151,12 @@
 	mdelay (20);
 	while (i--) {
 		temp = readl (&ehci->regs->port_status [i]);
-		if ((temp & PORT_SUSPEND) == 0)
-			continue;
-		temp &= ~(PORT_RWC_BITS | PORT_RESUME);
-		writel (temp, &ehci->regs->port_status [i]);
-		ehci_vdbg (ehci, "resumed port %d\n", i + 1);
+		if (test_bit(i, &ehci->bus_suspended) &&
+				(temp & PORT_SUSPEND)) {
+			temp &= ~(PORT_RWC_BITS | PORT_RESUME);
+			writel (temp, &ehci->regs->port_status [i]);
+			ehci_vdbg (ehci, "resumed port %d\n", i + 1);
+		}
 	}
 	(void) readl (&ehci->regs->command);
 
@@ -157,8 +175,7 @@
 	hcd->state = HC_STATE_RUNNING;
 
 	/* Now we can safely re-enable irqs */
-	if (intr_enable)
-		writel (INTR_MASK, &ehci->regs->intr_enable);
+	writel(INTR_MASK, &ehci->regs->intr_enable);
 
 	spin_unlock_irq (&ehci->lock);
 	return 0;
@@ -218,6 +235,7 @@
 {
 	struct ehci_hcd	*ehci = hcd_to_ehci (hcd);
 	u32		temp, status = 0;
+	u32		mask;
 	int		ports, i, retval = 1;
 	unsigned long	flags;
 
@@ -233,6 +251,18 @@
 		retval++;
 	}
 
+	/* Some boards (mostly VIA?) report bogus overcurrent indications,
+	 * causing massive log spam unless we completely ignore them.  It
+	 * may be relevant that VIA VT8235 controlers, where PORT_POWER is
+	 * always set, seem to clear PORT_OCC and PORT_CSC when writing to
+	 * PORT_POWER; that's surprising, but maybe within-spec.
+	 */
+	if (!ignore_oc)
+		mask = PORT_CSC | PORT_PEC | PORT_OCC;
+	else
+		mask = PORT_CSC | PORT_PEC;
+	// PORT_RESUME from hardware ~= PORT_STAT_C_SUSPEND
+
 	/* no hub change reports (bit 0) for now (power, ...) */
 
 	/* port N changes (bit N)? */
@@ -250,8 +280,7 @@
 		}
 		if (!(temp & PORT_CONNECT))
 			ehci->reset_done [i] = 0;
-		if ((temp & (PORT_CSC | PORT_PEC | PORT_OCC)) != 0
-				// PORT_STAT_C_SUSPEND?
+		if ((temp & mask) != 0
 				|| ((temp & PORT_RESUME) != 0
 					&& time_after (jiffies,
 						ehci->reset_done [i]))) {
@@ -319,6 +348,7 @@
 	u32		temp, status;
 	unsigned long	flags;
 	int		retval = 0;
+	unsigned	selector;
 
 	/*
 	 * FIXME:  support SetPortFeatures USB_PORT_FEAT_INDICATOR.
@@ -417,7 +447,7 @@
 			status |= 1 << USB_PORT_FEAT_C_CONNECTION;
 		if (temp & PORT_PEC)
 			status |= 1 << USB_PORT_FEAT_C_ENABLE;
-		if (temp & PORT_OCC)
+		if ((temp & PORT_OCC) && !ignore_oc)
 			status |= 1 << USB_PORT_FEAT_C_OVER_CURRENT;
 
 		/* whoever resumes must GetPortStatus to complete it!! */
@@ -506,6 +536,8 @@
 		}
 		break;
 	case SetPortFeature:
+		selector = wIndex >> 8;
+		wIndex &= 0xff;
 		if (!wIndex || wIndex > ports)
 			goto error;
 		wIndex--;
@@ -559,6 +591,22 @@
 			}
 			writel (temp, &ehci->regs->port_status [wIndex]);
 			break;
+
+		/* For downstream facing ports (these):  one hub port is put
+		 * into test mode according to USB2 11.24.2.13, then the hub
+		 * must be reset (which for root hub now means rmmod+modprobe,
+		 * or else system reboot).  See EHCI 2.3.9 and 4.14 for info
+		 * about the EHCI-specific stuff.
+		 */
+		case USB_PORT_FEAT_TEST:
+			if (!selector || selector > 5)
+				goto error;
+			ehci_quiesce(ehci);
+			ehci_halt(ehci);
+			temp |= selector << 16;
+			writel (temp, &ehci->regs->port_status [wIndex]);
+			break;
+
 		default:
 			goto error;
 		}
diff --git a/drivers/usb/host/ehci-pci.c b/drivers/usb/host/ehci-pci.c
index e51c1ed8..4bc7970 100644
--- a/drivers/usb/host/ehci-pci.c
+++ b/drivers/usb/host/ehci-pci.c
@@ -257,9 +257,7 @@
 static int ehci_pci_resume(struct usb_hcd *hcd)
 {
 	struct ehci_hcd		*ehci = hcd_to_ehci(hcd);
-	unsigned		port;
 	struct pci_dev		*pdev = to_pci_dev(hcd->self.controller);
-	int			retval = -EINVAL;
 
 	// maybe restore FLADJ
 
@@ -269,27 +267,19 @@
 	/* Mark hardware accessible again as we are out of D3 state by now */
 	set_bit(HCD_FLAG_HW_ACCESSIBLE, &hcd->flags);
 
-	/* If CF is clear, we lost PCI Vaux power and need to restart.  */
-	if (readl(&ehci->regs->configured_flag) != FLAG_CF)
-		goto restart;
-
-	/* If any port is suspended (or owned by the companion),
-	 * we know we can/must resume the HC (and mustn't reset it).
-	 * We just defer that to the root hub code.
+	/* If CF is still set, we maintained PCI Vaux power.
+	 * Just undo the effect of ehci_pci_suspend().
 	 */
-	for (port = HCS_N_PORTS(ehci->hcs_params); port > 0; ) {
-		u32	status;
-		port--;
-		status = readl(&ehci->regs->port_status [port]);
-		if (!(status & PORT_POWER))
-			continue;
-		if (status & (PORT_SUSPEND | PORT_RESUME | PORT_OWNER)) {
-			usb_hcd_resume_root_hub(hcd);
-			return 0;
-		}
+	if (readl(&ehci->regs->configured_flag) == FLAG_CF) {
+		int	mask = INTR_MASK;
+
+		if (!device_may_wakeup(&hcd->self.root_hub->dev))
+			mask &= ~STS_PCD;
+		writel(mask, &ehci->regs->intr_enable);
+		readl(&ehci->regs->intr_enable);
+		return 0;
 	}
 
-restart:
 	ehci_dbg(ehci, "lost power, restarting\n");
 	usb_root_hub_lost_power(hcd->self.root_hub);
 
@@ -307,13 +297,15 @@
 	ehci_work(ehci);
 	spin_unlock_irq(&ehci->lock);
 
-	/* restart; khubd will disconnect devices */
-	retval = ehci_run(hcd);
-
 	/* here we "know" root ports should always stay powered */
 	ehci_port_power(ehci, 1);
 
-	return retval;
+	writel(ehci->command, &ehci->regs->command);
+	writel(FLAG_CF, &ehci->regs->configured_flag);
+	readl(&ehci->regs->command);	/* unblock posted writes */
+
+	hcd->state = HC_STATE_SUSPENDED;
+	return 0;
 }
 #endif
 
diff --git a/drivers/usb/host/ehci.h b/drivers/usb/host/ehci.h
index bbc3082..74dbc6c 100644
--- a/drivers/usb/host/ehci.h
+++ b/drivers/usb/host/ehci.h
@@ -74,6 +74,7 @@
 
 	/* per root hub port */
 	unsigned long		reset_done [EHCI_MAX_ROOT_PORTS];
+	unsigned long		bus_suspended;
 
 	/* per-HC memory pools (could be per-bus, but ...) */
 	struct dma_pool		*qh_pool;	/* qh per active urb */
diff --git a/drivers/usb/host/ohci-hcd.c b/drivers/usb/host/ohci-hcd.c
index ea4714e..a95275a 100644
--- a/drivers/usb/host/ohci-hcd.c
+++ b/drivers/usb/host/ohci-hcd.c
@@ -729,6 +729,16 @@
 		ohci->next_statechange = jiffies + STATECHANGE_DELAY;
 		ohci_writel(ohci, OHCI_INTR_RD | OHCI_INTR_RHSC,
 				&regs->intrstatus);
+
+		/* NOTE: Vendors didn't always make the same implementation
+		 * choices for RHSC.  Many followed the spec; RHSC triggers
+		 * on an edge, like setting and maybe clearing a port status
+		 * change bit.  With others it's level-triggered, active
+		 * until khubd clears all the port status change bits.  We'll
+		 * always disable it here and rely on polling until khubd
+		 * re-enables it.
+		 */
+		ohci_writel(ohci, OHCI_INTR_RHSC, &regs->intrdisable);
 		usb_hcd_poll_rh_status(hcd);
 	}
 
diff --git a/drivers/usb/host/ohci-hub.c b/drivers/usb/host/ohci-hub.c
index 6995ea3..2441642 100644
--- a/drivers/usb/host/ohci-hub.c
+++ b/drivers/usb/host/ohci-hub.c
@@ -41,7 +41,11 @@
 {
 	struct ohci_hcd		*ohci = hcd_to_ohci (hcd);
 
-	ohci_writel (ohci, OHCI_INTR_RHSC, &ohci->regs->intrenable);
+	spin_lock_irq(&ohci->lock);
+	if (!ohci->autostop)
+		del_timer(&hcd->rh_timer);	/* Prevent next poll */
+	ohci_writel(ohci, OHCI_INTR_RHSC, &ohci->regs->intrenable);
+	spin_unlock_irq(&ohci->lock);
 }
 
 #define OHCI_SCHED_ENABLES \
@@ -50,6 +54,9 @@
 static void dl_done_list (struct ohci_hcd *);
 static void finish_unlinks (struct ohci_hcd *, u16);
 
+#ifdef	CONFIG_PM
+static int ohci_restart(struct ohci_hcd *ohci);
+
 static int ohci_rh_suspend (struct ohci_hcd *ohci, int autostop)
 __releases(ohci->lock)
 __acquires(ohci->lock)
@@ -132,8 +139,6 @@
 	return ed;
 }
 
-static int ohci_restart (struct ohci_hcd *ohci);
-
 /* caller has locked the root hub */
 static int ohci_rh_resume (struct ohci_hcd *ohci)
 __releases(ohci->lock)
@@ -169,7 +174,7 @@
 		break;
 	case OHCI_USB_RESUME:
 		/* HCFS changes sometime after INTR_RD */
-		ohci_info(ohci, "%swakeup\n",
+		ohci_dbg(ohci, "%swakeup root hub\n",
 				autostopped ? "auto-" : "");
 		break;
 	case OHCI_USB_OPER:
@@ -181,7 +186,6 @@
 		ohci_dbg (ohci, "lost power\n");
 		status = -EBUSY;
 	}
-#ifdef	CONFIG_PM
 	if (status == -EBUSY) {
 		if (!autostopped) {
 			spin_unlock_irq (&ohci->lock);
@@ -191,25 +195,12 @@
 		}
 		return status;
 	}
-#endif
 	if (status != -EINPROGRESS)
 		return status;
 	if (autostopped)
 		goto skip_resume;
 	spin_unlock_irq (&ohci->lock);
 
-	temp = ohci->num_ports;
-	while (temp--) {
-		u32 stat = ohci_readl (ohci,
-				       &ohci->regs->roothub.portstatus [temp]);
-
-		/* force global, not selective, resume */
-		if (!(stat & RH_PS_PSS))
-			continue;
-		ohci_writel (ohci, RH_PS_POCI,
-				&ohci->regs->roothub.portstatus [temp]);
-	}
-
 	/* Some controllers (lucent erratum) need extra-long delays */
 	msleep (20 /* usb 11.5.1.10 */ + 12 /* 32 msec counter */ + 1);
 
@@ -217,6 +208,7 @@
 	temp &= OHCI_CTRL_HCFS;
 	if (temp != OHCI_USB_RESUME) {
 		ohci_err (ohci, "controller won't resume\n");
+		spin_lock_irq(&ohci->lock);
 		return -EBUSY;
 	}
 
@@ -296,8 +288,6 @@
 	return 0;
 }
 
-#ifdef	CONFIG_PM
-
 static int ohci_bus_suspend (struct usb_hcd *hcd)
 {
 	struct ohci_hcd		*ohci = hcd_to_ohci (hcd);
@@ -335,6 +325,83 @@
 	return rc;
 }
 
+/* Carry out polling-, autostop-, and autoresume-related state changes */
+static int ohci_root_hub_state_changes(struct ohci_hcd *ohci, int changed,
+		int any_connected)
+{
+	int	poll_rh = 1;
+
+	switch (ohci->hc_control & OHCI_CTRL_HCFS) {
+
+	case OHCI_USB_OPER:
+		/* keep on polling until we know a device is connected
+		 * and RHSC is enabled */
+		if (!ohci->autostop) {
+			if (any_connected ||
+					!device_may_wakeup(&ohci_to_hcd(ohci)
+						->self.root_hub->dev)) {
+				if (ohci_readl(ohci, &ohci->regs->intrenable) &
+						OHCI_INTR_RHSC)
+					poll_rh = 0;
+			} else {
+				ohci->autostop = 1;
+				ohci->next_statechange = jiffies + HZ;
+			}
+
+		/* if no devices have been attached for one second, autostop */
+		} else {
+			if (changed || any_connected) {
+				ohci->autostop = 0;
+				ohci->next_statechange = jiffies +
+						STATECHANGE_DELAY;
+			} else if (time_after_eq(jiffies,
+						ohci->next_statechange)
+					&& !ohci->ed_rm_list
+					&& !(ohci->hc_control &
+						OHCI_SCHED_ENABLES)) {
+				ohci_rh_suspend(ohci, 1);
+			}
+		}
+		break;
+
+	/* if there is a port change, autostart or ask to be resumed */
+	case OHCI_USB_SUSPEND:
+	case OHCI_USB_RESUME:
+		if (changed) {
+			if (ohci->autostop)
+				ohci_rh_resume(ohci);
+			else
+				usb_hcd_resume_root_hub(ohci_to_hcd(ohci));
+		} else {
+			/* everything is idle, no need for polling */
+			poll_rh = 0;
+		}
+		break;
+	}
+	return poll_rh;
+}
+
+#else	/* CONFIG_PM */
+
+static inline int ohci_rh_resume(struct ohci_hcd *ohci)
+{
+	return 0;
+}
+
+/* Carry out polling-related state changes.
+ * autostop isn't used when CONFIG_PM is turned off.
+ */
+static int ohci_root_hub_state_changes(struct ohci_hcd *ohci, int changed,
+		int any_connected)
+{
+	int	poll_rh = 1;
+
+	/* keep on polling until RHSC is enabled */
+	if (ohci_readl(ohci, &ohci->regs->intrenable) & OHCI_INTR_RHSC)
+		poll_rh = 0;
+	return poll_rh;
+}
+
 #endif	/* CONFIG_PM */
 
 /*-------------------------------------------------------------------------*/
@@ -346,7 +413,7 @@
 {
 	struct ohci_hcd	*ohci = hcd_to_ohci (hcd);
 	int		i, changed = 0, length = 1;
-	int		any_connected = 0, rhsc_enabled = 1;
+	int		any_connected = 0;
 	unsigned long	flags;
 
 	spin_lock_irqsave (&ohci->lock, flags);
@@ -387,67 +454,8 @@
 		}
 	}
 
-	/* NOTE:  vendors didn't always make the same implementation
-	 * choices for RHSC.  Sometimes it triggers on an edge (like
-	 * setting and maybe clearing a port status change bit); and
-	 * it's level-triggered on other silicon, active until khubd
-	 * clears all active port status change bits.  If it's still
-	 * set (level-triggered) we must disable it and rely on
-	 * polling until khubd re-enables it.
-	 */
-	if (ohci_readl (ohci, &ohci->regs->intrstatus) & OHCI_INTR_RHSC) {
-		ohci_writel (ohci, OHCI_INTR_RHSC, &ohci->regs->intrdisable);
-		(void) ohci_readl (ohci, &ohci->regs->intrdisable);
-		rhsc_enabled = 0;
-	}
-	hcd->poll_rh = 1;
-
-	/* carry out appropriate state changes */
-	switch (ohci->hc_control & OHCI_CTRL_HCFS) {
-
-	case OHCI_USB_OPER:
-		/* keep on polling until we know a device is connected
-		 * and RHSC is enabled */
-		if (!ohci->autostop) {
-			if (any_connected) {
-				if (rhsc_enabled)
-					hcd->poll_rh = 0;
-			} else {
-				ohci->autostop = 1;
-				ohci->next_statechange = jiffies + HZ;
-			}
-
-		/* if no devices have been attached for one second, autostop */
-		} else {
-			if (changed || any_connected) {
-				ohci->autostop = 0;
-				ohci->next_statechange = jiffies +
-						STATECHANGE_DELAY;
-			} else if (device_may_wakeup(&hcd->self.root_hub->dev)
-					&& time_after_eq(jiffies,
-						ohci->next_statechange)
-					&& !ohci->ed_rm_list
-					&& !(ohci->hc_control &
-						OHCI_SCHED_ENABLES)) {
-				ohci_rh_suspend (ohci, 1);
-			}
-		}
-		break;
-
-	/* if there is a port change, autostart or ask to be resumed */
-	case OHCI_USB_SUSPEND:
-	case OHCI_USB_RESUME:
-		if (changed) {
-			if (ohci->autostop)
-				ohci_rh_resume (ohci);
-			else
-				usb_hcd_resume_root_hub (hcd);
-		} else {
-			/* everything is idle, no need for polling */
-			hcd->poll_rh = 0;
-		}
-		break;
-	}
+	hcd->poll_rh = ohci_root_hub_state_changes(ohci, changed,
+			any_connected);
 
 done:
 	spin_unlock_irqrestore (&ohci->lock, flags);
diff --git a/drivers/usb/host/u132-hcd.c b/drivers/usb/host/u132-hcd.c
index 32c635e..ef54e310b 100644
--- a/drivers/usb/host/u132-hcd.c
+++ b/drivers/usb/host/u132-hcd.c
@@ -71,7 +71,7 @@
 module_param(distrust_firmware, bool, 0);
 MODULE_PARM_DESC(distrust_firmware, "true to distrust firmware power/overcurren"
         "t setup");
-DECLARE_WAIT_QUEUE_HEAD(u132_hcd_wait);
+static DECLARE_WAIT_QUEUE_HEAD(u132_hcd_wait);
 /*
 * u132_module_lock exists to protect access to global variables
 *
@@ -205,13 +205,9 @@
         struct u132_port port[MAX_U132_PORTS];
         struct u132_endp *endp[MAX_U132_ENDPS];
 };
-int usb_ftdi_elan_read_reg(struct platform_device *pdev, u32 *data);
-int usb_ftdi_elan_read_pcimem(struct platform_device *pdev, u8 addressofs,
-        u8 width, u32 *data);
-int usb_ftdi_elan_write_pcimem(struct platform_device *pdev, u8 addressofs,
-        u8 width, u32 data);
+
 /*
-* these can not be inlines because we need the structure offset!!
+* these cannot be inlines because we need the structure offset!!
 * Does anyone have a better way?????
 */
 #define u132_read_pcimem(u132, member, data) \
@@ -3045,7 +3041,7 @@
 * This function may be called by the USB core whilst the "usb_all_devices_rwsem"
 * is held for writing, thus this module must not call usb_remove_hcd()
 * synchronously - but instead should immediately stop activity to the
-* device and ansynchronously call usb_remove_hcd()
+* device and asynchronously call usb_remove_hcd()
 */
 static int __devexit u132_remove(struct platform_device *pdev)
 {
@@ -3241,7 +3237,7 @@
 #define u132_resume NULL
 #endif
 /*
-* this driver is loaded explicitely by ftdi_u132
+* this driver is loaded explicitly by ftdi_u132
 *
 * the platform_driver struct is static because it is per type of module
 */
diff --git a/drivers/usb/image/microtek.c b/drivers/usb/image/microtek.c
index 3038ed0..8ccddf7 100644
--- a/drivers/usb/image/microtek.c
+++ b/drivers/usb/image/microtek.c
@@ -796,7 +796,7 @@
 
 	new_desc->context.scsi_status = kmalloc(1, GFP_KERNEL);
 	if (!new_desc->context.scsi_status)
-		goto out_kfree2;
+		goto out_free_urb;
 
 	new_desc->usb_dev = dev;
 	new_desc->usb_intf = intf;
@@ -822,18 +822,20 @@
 	new_desc->host = scsi_host_alloc(&mts_scsi_host_template,
 			sizeof(new_desc));
 	if (!new_desc->host)
-		goto out_free_urb;
+		goto out_kfree2;
 
 	new_desc->host->hostdata[0] = (unsigned long)new_desc;
 	if (scsi_add_host(new_desc->host, NULL)) {
 		err_retval = -EIO;
-		goto out_free_urb;
+		goto out_host_put;
 	}
 	scsi_scan_host(new_desc->host);
 
 	usb_set_intfdata(intf, new_desc);
 	return 0;
 
+ out_host_put:
+	scsi_host_put(new_desc->host);
  out_kfree2:
 	kfree(new_desc->context.scsi_status);
  out_free_urb:
diff --git a/drivers/usb/input/Kconfig b/drivers/usb/input/Kconfig
index 20db364..661af7a 100644
--- a/drivers/usb/input/Kconfig
+++ b/drivers/usb/input/Kconfig
@@ -221,6 +221,7 @@
 	  - ITM
 	  - some other eTurboTouch
 	  - Gunze AHL61
+	  - DMC TSC-10/25
 
 	  Have a look at <http://linux.chapter7.ch/touchkit/> for
 	  a usage description and the required user-space stuff.
@@ -258,6 +259,11 @@
 	bool "Gunze AHL61 device support" if EMBEDDED
 	depends on USB_TOUCHSCREEN
 
+config USB_TOUCHSCREEN_DMC_TSC10
+	default y
+	bool "DMC TSC-10/25 device support" if EMBEDDED
+	depends on USB_TOUCHSCREEN
+
 config USB_YEALINK
 	tristate "Yealink usb-p1k voip phone"
 	depends on USB && INPUT && EXPERIMENTAL
diff --git a/drivers/usb/input/ati_remote.c b/drivers/usb/input/ati_remote.c
index 787b847..ff23318 100644
--- a/drivers/usb/input/ati_remote.c
+++ b/drivers/usb/input/ati_remote.c
@@ -630,11 +630,8 @@
  */
 static void ati_remote_free_buffers(struct ati_remote *ati_remote)
 {
-	if (ati_remote->irq_urb)
-		usb_free_urb(ati_remote->irq_urb);
-
-	if (ati_remote->out_urb)
-		usb_free_urb(ati_remote->out_urb);
+	usb_free_urb(ati_remote->irq_urb);
+	usb_free_urb(ati_remote->out_urb);
 
 	usb_buffer_free(ati_remote->udev, DATA_BUFSIZE,
 		ati_remote->inbuf, ati_remote->inbuf_dma);
diff --git a/drivers/usb/input/ati_remote2.c b/drivers/usb/input/ati_remote2.c
index f982a2b..83f1f79 100644
--- a/drivers/usb/input/ati_remote2.c
+++ b/drivers/usb/input/ati_remote2.c
@@ -372,8 +372,7 @@
 	int i;
 
 	for (i = 0; i < 2; i++) {
-		if (ar2->urb[i])
-			usb_free_urb(ar2->urb[i]);
+		usb_free_urb(ar2->urb[i]);
 
 		if (ar2->buf[i])
 			usb_buffer_free(ar2->udev, 4, ar2->buf[i], ar2->buf_dma[i]);
diff --git a/drivers/usb/input/hid-core.c b/drivers/usb/input/hid-core.c
index 6d08a3b..a49644b 100644
--- a/drivers/usb/input/hid-core.c
+++ b/drivers/usb/input/hid-core.c
@@ -968,20 +968,29 @@
 		hid_io_error(hid);
 }
 
-/* Workqueue routine to reset the device */
+/* Workqueue routine to reset the device or clear a halt */
 static void hid_reset(void *_hid)
 {
 	struct hid_device *hid = (struct hid_device *) _hid;
-	int rc_lock, rc;
+	int rc_lock, rc = 0;
 
-	dev_dbg(&hid->intf->dev, "resetting device\n");
-	rc = rc_lock = usb_lock_device_for_reset(hid->dev, hid->intf);
-	if (rc_lock >= 0) {
-		rc = usb_reset_composite_device(hid->dev, hid->intf);
-		if (rc_lock)
-			usb_unlock_device(hid->dev);
+	if (test_bit(HID_CLEAR_HALT, &hid->iofl)) {
+		dev_dbg(&hid->intf->dev, "clear halt\n");
+		rc = usb_clear_halt(hid->dev, hid->urbin->pipe);
+		clear_bit(HID_CLEAR_HALT, &hid->iofl);
+		hid_start_in(hid);
 	}
-	clear_bit(HID_RESET_PENDING, &hid->iofl);
+
+	else if (test_bit(HID_RESET_PENDING, &hid->iofl)) {
+		dev_dbg(&hid->intf->dev, "resetting device\n");
+		rc = rc_lock = usb_lock_device_for_reset(hid->dev, hid->intf);
+		if (rc_lock >= 0) {
+			rc = usb_reset_composite_device(hid->dev, hid->intf);
+			if (rc_lock)
+				usb_unlock_device(hid->dev);
+		}
+		clear_bit(HID_RESET_PENDING, &hid->iofl);
+	}
 
 	switch (rc) {
 	case 0:
@@ -1023,9 +1032,8 @@
 
 		/* Retries failed, so do a port reset */
 		if (!test_and_set_bit(HID_RESET_PENDING, &hid->iofl)) {
-			if (schedule_work(&hid->reset_work))
-				goto done;
-			clear_bit(HID_RESET_PENDING, &hid->iofl);
+			schedule_work(&hid->reset_work);
+			goto done;
 		}
 	}
 
@@ -1049,6 +1057,11 @@
 			hid->retry_delay = 0;
 			hid_input_report(HID_INPUT_REPORT, urb, 1);
 			break;
+		case -EPIPE:		/* stall */
+			clear_bit(HID_IN_RUNNING, &hid->iofl);
+			set_bit(HID_CLEAR_HALT, &hid->iofl);
+			schedule_work(&hid->reset_work);
+			return;
 		case -ECONNRESET:	/* unlink */
 		case -ENOENT:
 		case -ESHUTDOWN:	/* unplug */
@@ -1627,6 +1640,19 @@
 
 #define USB_VENDOR_ID_APPLE		0x05ac
 #define USB_DEVICE_ID_APPLE_MIGHTYMOUSE	0x0304
+#define USB_DEVICE_ID_APPLE_FOUNTAIN_ANSI	0x020e
+#define USB_DEVICE_ID_APPLE_FOUNTAIN_ISO	0x020f
+#define USB_DEVICE_ID_APPLE_GEYSER_ANSI	0x0214
+#define USB_DEVICE_ID_APPLE_GEYSER_ISO	0x0215
+#define USB_DEVICE_ID_APPLE_GEYSER_JIS	0x0216
+#define USB_DEVICE_ID_APPLE_GEYSER3_ANSI	0x0217
+#define USB_DEVICE_ID_APPLE_GEYSER3_ISO	0x0218
+#define USB_DEVICE_ID_APPLE_GEYSER3_JIS	0x0219
+#define USB_DEVICE_ID_APPLE_GEYSER4_ANSI	0x021a
+#define USB_DEVICE_ID_APPLE_GEYSER4_ISO	0x021b
+#define USB_DEVICE_ID_APPLE_GEYSER4_JIS	0x021c
+#define USB_DEVICE_ID_APPLE_FOUNTAIN_TP_ONLY	0x030a
+#define USB_DEVICE_ID_APPLE_GEYSER1_TP_ONLY	0x030b
 
 #define USB_VENDOR_ID_CHERRY		0x046a
 #define USB_DEVICE_ID_CHERRY_CYMOTION	0x0023
@@ -1794,17 +1820,19 @@
 
 	{ USB_VENDOR_ID_CHERRY, USB_DEVICE_ID_CHERRY_CYMOTION, HID_QUIRK_CYMOTION },
 
-	{ USB_VENDOR_ID_APPLE, 0x020E, HID_QUIRK_POWERBOOK_HAS_FN },
-	{ USB_VENDOR_ID_APPLE, 0x020F, HID_QUIRK_POWERBOOK_HAS_FN },
-	{ USB_VENDOR_ID_APPLE, 0x0214, HID_QUIRK_POWERBOOK_HAS_FN },
-	{ USB_VENDOR_ID_APPLE, 0x0215, HID_QUIRK_POWERBOOK_HAS_FN | HID_QUIRK_POWERBOOK_ISO_KEYBOARD},
-	{ USB_VENDOR_ID_APPLE, 0x0216, HID_QUIRK_POWERBOOK_HAS_FN },
-	{ USB_VENDOR_ID_APPLE, 0x0217, HID_QUIRK_POWERBOOK_HAS_FN },
-	{ USB_VENDOR_ID_APPLE, 0x0218, HID_QUIRK_POWERBOOK_HAS_FN | HID_QUIRK_POWERBOOK_ISO_KEYBOARD},
-	{ USB_VENDOR_ID_APPLE, 0x0219, HID_QUIRK_POWERBOOK_HAS_FN },
-	{ USB_VENDOR_ID_APPLE, 0x021B, HID_QUIRK_POWERBOOK_HAS_FN },
-	{ USB_VENDOR_ID_APPLE, 0x030A, HID_QUIRK_POWERBOOK_HAS_FN },
-	{ USB_VENDOR_ID_APPLE, 0x030B, HID_QUIRK_POWERBOOK_HAS_FN },
+	{ USB_VENDOR_ID_APPLE, USB_DEVICE_ID_APPLE_FOUNTAIN_ANSI, HID_QUIRK_POWERBOOK_HAS_FN },
+	{ USB_VENDOR_ID_APPLE, USB_DEVICE_ID_APPLE_FOUNTAIN_ISO, HID_QUIRK_POWERBOOK_HAS_FN },
+	{ USB_VENDOR_ID_APPLE, USB_DEVICE_ID_APPLE_GEYSER_ANSI, HID_QUIRK_POWERBOOK_HAS_FN },
+	{ USB_VENDOR_ID_APPLE, USB_DEVICE_ID_APPLE_GEYSER_ISO, HID_QUIRK_POWERBOOK_HAS_FN | HID_QUIRK_POWERBOOK_ISO_KEYBOARD},
+	{ USB_VENDOR_ID_APPLE, USB_DEVICE_ID_APPLE_GEYSER_JIS, HID_QUIRK_POWERBOOK_HAS_FN },
+	{ USB_VENDOR_ID_APPLE, USB_DEVICE_ID_APPLE_GEYSER3_ANSI, HID_QUIRK_POWERBOOK_HAS_FN },
+	{ USB_VENDOR_ID_APPLE, USB_DEVICE_ID_APPLE_GEYSER3_ISO, HID_QUIRK_POWERBOOK_HAS_FN | HID_QUIRK_POWERBOOK_ISO_KEYBOARD},
+	{ USB_VENDOR_ID_APPLE, USB_DEVICE_ID_APPLE_GEYSER3_JIS, HID_QUIRK_POWERBOOK_HAS_FN },
+	{ USB_VENDOR_ID_APPLE, USB_DEVICE_ID_APPLE_GEYSER4_ANSI, HID_QUIRK_POWERBOOK_HAS_FN },
+	{ USB_VENDOR_ID_APPLE, USB_DEVICE_ID_APPLE_GEYSER4_ISO, HID_QUIRK_POWERBOOK_HAS_FN },
+	{ USB_VENDOR_ID_APPLE, USB_DEVICE_ID_APPLE_GEYSER4_JIS, HID_QUIRK_POWERBOOK_HAS_FN },
+	{ USB_VENDOR_ID_APPLE, USB_DEVICE_ID_APPLE_FOUNTAIN_TP_ONLY, HID_QUIRK_POWERBOOK_HAS_FN },
+	{ USB_VENDOR_ID_APPLE, USB_DEVICE_ID_APPLE_GEYSER1_TP_ONLY, HID_QUIRK_POWERBOOK_HAS_FN },
 
 	{ USB_VENDOR_ID_PANJIT, 0x0001, HID_QUIRK_IGNORE },
 	{ USB_VENDOR_ID_PANJIT, 0x0002, HID_QUIRK_IGNORE },
@@ -1985,7 +2013,7 @@
 		if (hid->collection->usage == HID_GD_MOUSE && hid_mousepoll_interval > 0)
 			interval = hid_mousepoll_interval;
 
-		if (endpoint->bEndpointAddress & USB_DIR_IN) {
+		if (usb_endpoint_dir_in(endpoint)) {
 			if (hid->urbin)
 				continue;
 			if (!(hid->urbin = usb_alloc_urb(0, GFP_KERNEL)))
@@ -2067,13 +2095,9 @@
 	return hid;
 
 fail:
-
-	if (hid->urbin)
-		usb_free_urb(hid->urbin);
-	if (hid->urbout)
-		usb_free_urb(hid->urbout);
-	if (hid->urbctrl)
-		usb_free_urb(hid->urbctrl);
+	usb_free_urb(hid->urbin);
+	usb_free_urb(hid->urbout);
+	usb_free_urb(hid->urbctrl);
 	hid_free_buffers(dev, hid);
 	hid_free_device(hid);
 
@@ -2104,8 +2128,7 @@
 
 	usb_free_urb(hid->urbin);
 	usb_free_urb(hid->urbctrl);
-	if (hid->urbout)
-		usb_free_urb(hid->urbout);
+	usb_free_urb(hid->urbout);
 
 	hid_free_buffers(hid->dev, hid);
 	hid_free_device(hid);
diff --git a/drivers/usb/input/hid.h b/drivers/usb/input/hid.h
index 0e76e6d..2a9bf07 100644
--- a/drivers/usb/input/hid.h
+++ b/drivers/usb/input/hid.h
@@ -385,6 +385,7 @@
 #define HID_IN_RUNNING		3
 #define HID_RESET_PENDING	4
 #define HID_SUSPENDED		5
+#define HID_CLEAR_HALT		6
 
 struct hid_input {
 	struct list_head list;
diff --git a/drivers/usb/input/usbkbd.c b/drivers/usb/input/usbkbd.c
index c73285c..dac8864 100644
--- a/drivers/usb/input/usbkbd.c
+++ b/drivers/usb/input/usbkbd.c
@@ -208,10 +208,8 @@
 
 static void usb_kbd_free_mem(struct usb_device *dev, struct usb_kbd *kbd)
 {
-	if (kbd->irq)
-		usb_free_urb(kbd->irq);
-	if (kbd->led)
-		usb_free_urb(kbd->led);
+	usb_free_urb(kbd->irq);
+	usb_free_urb(kbd->led);
 	if (kbd->new)
 		usb_buffer_free(dev, 8, kbd->new, kbd->new_dma);
 	if (kbd->cr)
@@ -236,9 +234,7 @@
 		return -ENODEV;
 
 	endpoint = &interface->endpoint[0].desc;
-	if (!(endpoint->bEndpointAddress & USB_DIR_IN))
-		return -ENODEV;
-	if ((endpoint->bmAttributes & USB_ENDPOINT_XFERTYPE_MASK) != USB_ENDPOINT_XFER_INT)
+	if (!usb_endpoint_is_int_in(endpoint))
 		return -ENODEV;
 
 	pipe = usb_rcvintpipe(dev, endpoint->bEndpointAddress);
diff --git a/drivers/usb/input/usbmouse.c b/drivers/usb/input/usbmouse.c
index cbbbea3..68a5564 100644
--- a/drivers/usb/input/usbmouse.c
+++ b/drivers/usb/input/usbmouse.c
@@ -126,9 +126,7 @@
 		return -ENODEV;
 
 	endpoint = &interface->endpoint[0].desc;
-	if (!(endpoint->bEndpointAddress & USB_DIR_IN))
-		return -ENODEV;
-	if ((endpoint->bmAttributes & USB_ENDPOINT_XFERTYPE_MASK) != USB_ENDPOINT_XFER_INT)
+	if (!usb_endpoint_is_int_in(endpoint))
 		return -ENODEV;
 
 	pipe = usb_rcvintpipe(dev, endpoint->bEndpointAddress);
diff --git a/drivers/usb/input/usbtouchscreen.c b/drivers/usb/input/usbtouchscreen.c
index 933cedd..49704d4 100644
--- a/drivers/usb/input/usbtouchscreen.c
+++ b/drivers/usb/input/usbtouchscreen.c
@@ -8,6 +8,7 @@
  *  - PanJit TouchSet
  *  - eTurboTouch
  *  - Gunze AHL61
+ *  - DMC TSC-10/25
  *
  * Copyright (C) 2004-2006 by Daniel Ritz <daniel.ritz@gmx.ch>
  * Copyright (C) by Todd E. Johnson (mtouchusb.c)
@@ -30,6 +31,8 @@
  * - ITM parts are from itmtouch.c
  * - 3M parts are from mtouchusb.c
  * - PanJit parts are from an unmerged driver by Lanslott Gish
+ * - DMC TSC 10/25 are from Holger Schurig, with ideas from an unmerged
+ *   driver from Marius Vollmer
  *
  *****************************************************************************/
 
@@ -44,7 +47,7 @@
 #include <linux/usb/input.h>
 
 
-#define DRIVER_VERSION		"v0.4"
+#define DRIVER_VERSION		"v0.5"
 #define DRIVER_AUTHOR		"Daniel Ritz <daniel.ritz@gmx.ch>"
 #define DRIVER_DESC		"USB Touchscreen Driver"
 
@@ -103,6 +106,7 @@
 	DEVTYPE_ITM,
 	DEVTYPE_ETURBO,
 	DEVTYPE_GUNZE,
+	DEVTYPE_DMC_TSC10,
 };
 
 static struct usb_device_id usbtouch_devices[] = {
@@ -139,6 +143,10 @@
 	{USB_DEVICE(0x0637, 0x0001), .driver_info = DEVTYPE_GUNZE},
 #endif
 
+#ifdef CONFIG_USB_TOUCHSCREEN_DMC_TSC10
+	{USB_DEVICE(0x0afa, 0x03e8), .driver_info = DEVTYPE_DMC_TSC10},
+#endif
+
 	{}
 };
 
@@ -313,6 +321,80 @@
 #endif
 
 /*****************************************************************************
+ * DMC TSC-10/25 Part
+ *
+ * Documentation about the controller and it's protocol can be found at
+ *   http://www.dmccoltd.com/files/controler/tsc10usb_pi_e.pdf
+ *   http://www.dmccoltd.com/files/controler/tsc25_usb_e.pdf
+ */
+#ifdef CONFIG_USB_TOUCHSCREEN_DMC_TSC10
+
+/* supported data rates. currently using 130 */
+#define TSC10_RATE_POINT	0x50
+#define TSC10_RATE_30		0x40
+#define TSC10_RATE_50		0x41
+#define TSC10_RATE_80		0x42
+#define TSC10_RATE_100		0x43
+#define TSC10_RATE_130		0x44
+#define TSC10_RATE_150		0x45
+
+/* commands */
+#define TSC10_CMD_RESET		0x55
+#define TSC10_CMD_RATE		0x05
+#define TSC10_CMD_DATA1		0x01
+
+static int dmc_tsc10_init(struct usbtouch_usb *usbtouch)
+{
+	struct usb_device *dev = usbtouch->udev;
+	int ret;
+	unsigned char buf[2];
+
+	/* reset */
+	buf[0] = buf[1] = 0xFF;
+	ret = usb_control_msg(dev, usb_rcvctrlpipe (dev, 0),
+	                      TSC10_CMD_RESET,
+	                      USB_DIR_IN | USB_TYPE_VENDOR | USB_RECIP_DEVICE,
+	                      0, 0, buf, 2, USB_CTRL_SET_TIMEOUT);
+	if (ret < 0)
+		return ret;
+	if (buf[0] != 0x06 || buf[1] != 0x00)
+		return -ENODEV;
+
+	/* set coordinate output rate */
+	buf[0] = buf[1] = 0xFF;
+	ret = usb_control_msg(dev, usb_rcvctrlpipe (dev, 0),
+	                      TSC10_CMD_RATE,
+	                      USB_DIR_IN | USB_TYPE_VENDOR | USB_RECIP_DEVICE,
+	                      TSC10_RATE_150, 0, buf, 2, USB_CTRL_SET_TIMEOUT);
+	if (ret < 0)
+		return ret;
+	if (buf[0] != 0x06 || buf[1] != 0x00)
+		return -ENODEV;
+
+	/* start sending data */
+	ret = usb_control_msg(dev, usb_rcvctrlpipe (dev, 0),
+	                      TSC10_CMD_DATA1,
+	                      USB_DIR_OUT | USB_TYPE_VENDOR | USB_RECIP_DEVICE,
+	                      0, 0, NULL, 0, USB_CTRL_SET_TIMEOUT);
+	if (ret < 0)
+		return ret;
+
+	return 0;
+}
+
+
+static int dmc_tsc10_read_data(unsigned char *pkt, int *x, int *y, int *touch, int *press)
+{
+	*x = ((pkt[2] & 0x03) << 8) | pkt[1];
+	*y = ((pkt[4] & 0x03) << 8) | pkt[3];
+	*touch = pkt[0] & 0x01;
+
+	return 1;
+}
+#endif
+
+
+/*****************************************************************************
  * the different device descriptors
  */
 static struct usbtouch_device_info usbtouch_dev_info[] = {
@@ -389,6 +471,18 @@
 		.read_data	= gunze_read_data,
 	},
 #endif
+
+#ifdef CONFIG_USB_TOUCHSCREEN_DMC_TSC10
+	[DEVTYPE_DMC_TSC10] = {
+		.min_xc		= 0x0,
+		.max_xc		= 0x03ff,
+		.min_yc		= 0x0,
+		.max_yc		= 0x03ff,
+		.rept_size	= 5,
+		.init		= dmc_tsc10_init,
+		.read_data	= dmc_tsc10_read_data,
+	},
+#endif
 };
 
 
diff --git a/drivers/usb/input/wacom.h b/drivers/usb/input/wacom.h
index 1cf08f0..d85abfc 100644
--- a/drivers/usb/input/wacom.h
+++ b/drivers/usb/input/wacom.h
@@ -110,7 +110,6 @@
 };
 
 extern int wacom_wac_irq(struct wacom_wac * wacom_wac, void * wcombo);
-extern void wacom_sys_irq(struct urb *urb);
 extern void wacom_report_abs(void *wcombo, unsigned int abs_type, int abs_data);
 extern void wacom_report_rel(void *wcombo, unsigned int rel_type, int rel_data);
 extern void wacom_report_key(void *wcombo, unsigned int key_type, int key_data);
diff --git a/drivers/usb/input/wacom_sys.c b/drivers/usb/input/wacom_sys.c
index 3498b89..e7cc20a 100644
--- a/drivers/usb/input/wacom_sys.c
+++ b/drivers/usb/input/wacom_sys.c
@@ -42,7 +42,7 @@
 	return wcombo->wacom->dev;
 }
 
-void wacom_sys_irq(struct urb *urb)
+static void wacom_sys_irq(struct urb *urb)
 {
 	struct wacom *wacom = urb->context;
 	struct wacom_combo wcombo;
diff --git a/drivers/usb/input/yealink.c b/drivers/usb/input/yealink.c
index 905bf63..2268ca3 100644
--- a/drivers/usb/input/yealink.c
+++ b/drivers/usb/input/yealink.c
@@ -859,10 +859,8 @@
 
 	interface = intf->cur_altsetting;
 	endpoint = &interface->endpoint[0].desc;
-	if (!(endpoint->bEndpointAddress & USB_DIR_IN))
-		return -EIO;
-	if ((endpoint->bmAttributes & USB_ENDPOINT_XFERTYPE_MASK) != USB_ENDPOINT_XFER_INT)
-		return -EIO;
+	if (!usb_endpoint_is_int_in(endpoint))
+		return -ENODEV;
 
 	yld = kzalloc(sizeof(struct yealink_dev), GFP_KERNEL);
 	if (!yld)
diff --git a/drivers/usb/misc/Makefile b/drivers/usb/misc/Makefile
index 11dc595..2cba07d 100644
--- a/drivers/usb/misc/Makefile
+++ b/drivers/usb/misc/Makefile
@@ -4,6 +4,7 @@
 #
 
 obj-$(CONFIG_USB_ADUTUX)	+= adutux.o
+obj-$(CONFIG_USB_APPLEDISPLAY)	+= appledisplay.o
 obj-$(CONFIG_USB_AUERSWALD)	+= auerswald.o
 obj-$(CONFIG_USB_CYPRESS_CY7C63)+= cypress_cy7c63.o
 obj-$(CONFIG_USB_CYTHERM)	+= cytherm.o
diff --git a/drivers/usb/misc/appledisplay.c b/drivers/usb/misc/appledisplay.c
index 6b23a1d..ba30ca6 100644
--- a/drivers/usb/misc/appledisplay.c
+++ b/drivers/usb/misc/appledisplay.c
@@ -216,10 +216,7 @@
 	iface_desc = iface->cur_altsetting;
 	for (i = 0; i < iface_desc->desc.bNumEndpoints; i++) {
 		endpoint = &iface_desc->endpoint[i].desc;
-		if (!int_in_endpointAddr &&
-		    (endpoint->bEndpointAddress & USB_DIR_IN) &&
-		    ((endpoint->bmAttributes & USB_ENDPOINT_XFERTYPE_MASK) ==
-		     USB_ENDPOINT_XFER_INT)) {
+		if (!int_in_endpointAddr && usb_endpoint_is_int_in(endpoint)) {
 			/* we found an interrupt in endpoint */
 			int_in_endpointAddr = endpoint->bEndpointAddress;
 			break;
diff --git a/drivers/usb/misc/auerswald.c b/drivers/usb/misc/auerswald.c
index e4971d6..c703f73 100644
--- a/drivers/usb/misc/auerswald.c
+++ b/drivers/usb/misc/auerswald.c
@@ -704,9 +704,7 @@
 {
 	kfree(bp->bufp);
 	kfree(bp->dr);
-	if (bp->urbp) {
-		usb_free_urb(bp->urbp);
-	}
+	usb_free_urb(bp->urbp);
 	kfree(bp);
 }
 
@@ -1155,8 +1153,7 @@
         dbg ("auerswald_int_release");
 
         /* stop the int endpoint */
-        if (cp->inturbp)
-                usb_kill_urb (cp->inturbp);
+	usb_kill_urb (cp->inturbp);
 
         /* deallocate memory */
         auerswald_int_free (cp);
diff --git a/drivers/usb/misc/emi26.c b/drivers/usb/misc/emi26.c
index 1fd9cb8..5c0a26c 100644
--- a/drivers/usb/misc/emi26.c
+++ b/drivers/usb/misc/emi26.c
@@ -53,13 +53,12 @@
 static int emi26_writememory (struct usb_device *dev, int address, unsigned char *data, int length, __u8 request)
 {
 	int result;
-	unsigned char *buffer =  kmalloc (length, GFP_KERNEL);
+	unsigned char *buffer =  kmemdup(data, length, GFP_KERNEL);
 
 	if (!buffer) {
 		err("emi26: kmalloc(%d) failed.", length);
 		return -ENOMEM;
 	}
-	memcpy (buffer, data, length);
 	/* Note: usb_control_msg returns negative value on error or length of the
 	 * 		 data that was written! */
 	result = usb_control_msg (dev, usb_sndctrlpipe(dev, 0), request, 0x40, address, 0, buffer, length, 300);
diff --git a/drivers/usb/misc/emi62.c b/drivers/usb/misc/emi62.c
index fe35137..23153ea 100644
--- a/drivers/usb/misc/emi62.c
+++ b/drivers/usb/misc/emi62.c
@@ -61,13 +61,12 @@
 static int emi62_writememory (struct usb_device *dev, int address, unsigned char *data, int length, __u8 request)
 {
 	int result;
-	unsigned char *buffer =  kmalloc (length, GFP_KERNEL);
+	unsigned char *buffer =  kmemdup(data, length, GFP_KERNEL);
 
 	if (!buffer) {
 		err("emi62: kmalloc(%d) failed.", length);
 		return -ENOMEM;
 	}
-	memcpy (buffer, data, length);
 	/* Note: usb_control_msg returns negative value on error or length of the
 	 * 		 data that was written! */
 	result = usb_control_msg (dev, usb_sndctrlpipe(dev, 0), request, 0x40, address, 0, buffer, length, 300);
diff --git a/drivers/usb/misc/ftdi-elan.c b/drivers/usb/misc/ftdi-elan.c
index 9b591b8..cb0ba31 100644
--- a/drivers/usb/misc/ftdi-elan.c
+++ b/drivers/usb/misc/ftdi-elan.c
@@ -303,7 +303,7 @@
 
 
 EXPORT_SYMBOL_GPL(ftdi_elan_gone_away);
-void ftdi_release_platform_dev(struct device *dev)
+static void ftdi_release_platform_dev(struct device *dev)
 {
         dev->parent = NULL;
 }
@@ -1426,14 +1426,6 @@
         }
 }
 
-int usb_ftdi_elan_read_reg(struct platform_device *pdev, u32 *data)
-{
-        struct usb_ftdi *ftdi = platform_device_to_usb_ftdi(pdev);
-        return ftdi_elan_read_reg(ftdi, data);
-}
-
-
-EXPORT_SYMBOL_GPL(usb_ftdi_elan_read_reg);
 static int ftdi_elan_read_config(struct usb_ftdi *ftdi, int config_offset,
         u8 width, u32 *data)
 {
@@ -2633,10 +2625,7 @@
         for (i = 0; i < iface_desc->desc.bNumEndpoints; ++i) {
                 endpoint = &iface_desc->endpoint[i].desc;
                 if (!ftdi->bulk_in_endpointAddr &&
-                        ((endpoint->bEndpointAddress & USB_ENDPOINT_DIR_MASK)
-                        == USB_DIR_IN) && ((endpoint->bmAttributes &
-                        USB_ENDPOINT_XFERTYPE_MASK) == USB_ENDPOINT_XFER_BULK))
-                        {
+		    usb_endpoint_is_bulk_in(endpoint)) {
                         buffer_size = le16_to_cpu(endpoint->wMaxPacketSize);
                         ftdi->bulk_in_size = buffer_size;
                         ftdi->bulk_in_endpointAddr = endpoint->bEndpointAddress;
@@ -2649,10 +2638,7 @@
                         }
                 }
                 if (!ftdi->bulk_out_endpointAddr &&
-                        ((endpoint->bEndpointAddress & USB_ENDPOINT_DIR_MASK)
-                        == USB_DIR_OUT) && ((endpoint->bmAttributes &
-                        USB_ENDPOINT_XFERTYPE_MASK) == USB_ENDPOINT_XFER_BULK))
-                        {
+		    usb_endpoint_is_bulk_out(endpoint)) {
                         ftdi->bulk_out_endpointAddr =
                                 endpoint->bEndpointAddress;
                 }
diff --git a/drivers/usb/misc/idmouse.c b/drivers/usb/misc/idmouse.c
index 8e6e195..c941853 100644
--- a/drivers/usb/misc/idmouse.c
+++ b/drivers/usb/misc/idmouse.c
@@ -125,12 +125,12 @@
 
 static int idmouse_create_image(struct usb_idmouse *dev)
 {
-	int bytes_read = 0;
-	int bulk_read = 0;
-	int result = 0;
+	int bytes_read;
+	int bulk_read;
+	int result;
 
 	memcpy(dev->bulk_in_buffer, HEADER, sizeof(HEADER)-1);
-	bytes_read += sizeof(HEADER)-1;
+	bytes_read = sizeof(HEADER)-1;
 
 	/* reset the device and set a fast blink rate */
 	result = ftip_command(dev, FTIP_RELEASE, 0, 0);
@@ -208,9 +208,9 @@
 
 static int idmouse_open(struct inode *inode, struct file *file)
 {
-	struct usb_idmouse *dev = NULL;
+	struct usb_idmouse *dev;
 	struct usb_interface *interface;
-	int result = 0;
+	int result;
 
 	/* prevent disconnects */
 	mutex_lock(&disconnect_mutex);
@@ -305,7 +305,7 @@
 				loff_t * ppos)
 {
 	struct usb_idmouse *dev;
-	int result = 0;
+	int result;
 
 	dev = (struct usb_idmouse *) file->private_data;
 
@@ -329,7 +329,7 @@
 				const struct usb_device_id *id)
 {
 	struct usb_device *udev = interface_to_usbdev(interface);
-	struct usb_idmouse *dev = NULL;
+	struct usb_idmouse *dev;
 	struct usb_host_interface *iface_desc;
 	struct usb_endpoint_descriptor *endpoint;
 	int result;
@@ -350,11 +350,7 @@
 
 	/* set up the endpoint information - use only the first bulk-in endpoint */
 	endpoint = &iface_desc->endpoint[0].desc;
-	if (!dev->bulk_in_endpointAddr
-		&& (endpoint->bEndpointAddress & USB_DIR_IN)
-		&& ((endpoint->bmAttributes & USB_ENDPOINT_XFERTYPE_MASK) ==
-		USB_ENDPOINT_XFER_BULK)) {
-
+	if (!dev->bulk_in_endpointAddr && usb_endpoint_is_bulk_in(endpoint)) {
 		/* we found a bulk in endpoint */
 		dev->orig_bi_size = le16_to_cpu(endpoint->wMaxPacketSize);
 		dev->bulk_in_size = 0x200; /* works _much_ faster */
diff --git a/drivers/usb/misc/legousbtower.c b/drivers/usb/misc/legousbtower.c
index 2708949..5dce797 100644
--- a/drivers/usb/misc/legousbtower.c
+++ b/drivers/usb/misc/legousbtower.c
@@ -317,12 +317,8 @@
 	tower_abort_transfers (dev);
 
 	/* free data structures */
-	if (dev->interrupt_in_urb != NULL) {
-		usb_free_urb (dev->interrupt_in_urb);
-	}
-	if (dev->interrupt_out_urb != NULL) {
-		usb_free_urb (dev->interrupt_out_urb);
-	}
+	usb_free_urb(dev->interrupt_in_urb);
+	usb_free_urb(dev->interrupt_out_urb);
 	kfree (dev->read_buffer);
 	kfree (dev->interrupt_in_buffer);
 	kfree (dev->interrupt_out_buffer);
@@ -502,15 +498,11 @@
 	if (dev->interrupt_in_running) {
 		dev->interrupt_in_running = 0;
 		mb();
-		if (dev->interrupt_in_urb != NULL && dev->udev) {
+		if (dev->udev)
 			usb_kill_urb (dev->interrupt_in_urb);
-		}
 	}
-	if (dev->interrupt_out_busy) {
-		if (dev->interrupt_out_urb != NULL && dev->udev) {
-			usb_kill_urb (dev->interrupt_out_urb);
-		}
-	}
+	if (dev->interrupt_out_busy && dev->udev)
+		usb_kill_urb(dev->interrupt_out_urb);
 
 exit:
 	dbg(2, "%s: leave", __FUNCTION__);
@@ -898,14 +890,11 @@
 	for (i = 0; i < iface_desc->desc.bNumEndpoints; ++i) {
 		endpoint = &iface_desc->endpoint[i].desc;
 
-		if (((endpoint->bEndpointAddress & USB_ENDPOINT_DIR_MASK) == USB_DIR_IN) &&
-		    ((endpoint->bmAttributes & USB_ENDPOINT_XFERTYPE_MASK) == USB_ENDPOINT_XFER_INT)) {
-			dev->interrupt_in_endpoint = endpoint;
-		}
-
-		if (((endpoint->bEndpointAddress & USB_ENDPOINT_DIR_MASK) == USB_DIR_OUT) &&
-		    ((endpoint->bmAttributes & USB_ENDPOINT_XFERTYPE_MASK) == USB_ENDPOINT_XFER_INT)) {
-			dev->interrupt_out_endpoint = endpoint;
+		if (usb_endpoint_xfer_int(endpoint)) {
+			if (usb_endpoint_dir_in(endpoint))
+				dev->interrupt_in_endpoint = endpoint;
+			else
+				dev->interrupt_out_endpoint = endpoint;
 		}
 	}
 	if(dev->interrupt_in_endpoint == NULL) {
diff --git a/drivers/usb/misc/phidgetkit.c b/drivers/usb/misc/phidgetkit.c
index abb4dcd..9110793 100644
--- a/drivers/usb/misc/phidgetkit.c
+++ b/drivers/usb/misc/phidgetkit.c
@@ -551,7 +551,7 @@
 		return -ENODEV;
 
 	endpoint = &interface->endpoint[0].desc;
-	if (!(endpoint->bEndpointAddress & 0x80)) 
+	if (!usb_endpoint_dir_in(endpoint))
 		return -ENODEV;
 	/*
 	 * bmAttributes
@@ -650,8 +650,7 @@
 		device_remove_file(kit->dev, &dev_output_attrs[i]);
 out:
 	if (kit) {
-		if (kit->irq)
-			usb_free_urb(kit->irq);
+		usb_free_urb(kit->irq);
 		if (kit->data)
 			usb_buffer_free(dev, URB_INT_SIZE, kit->data, kit->data_dma);
 		if (kit->dev)
diff --git a/drivers/usb/misc/phidgetmotorcontrol.c b/drivers/usb/misc/phidgetmotorcontrol.c
index 5c780ca..c3469b0 100644
--- a/drivers/usb/misc/phidgetmotorcontrol.c
+++ b/drivers/usb/misc/phidgetmotorcontrol.c
@@ -323,7 +323,7 @@
 		return -ENODEV;
 
 	endpoint = &interface->endpoint[0].desc;
-	if (!(endpoint->bEndpointAddress & 0x80))
+	if (!usb_endpoint_dir_in(endpoint))
 		return -ENODEV;
 
 	/*
@@ -392,8 +392,7 @@
 		device_remove_file(mc->dev, &dev_attrs[i]);
 out:
 	if (mc) {
-		if (mc->irq)
-			usb_free_urb(mc->irq);
+		usb_free_urb(mc->irq);
 		if (mc->data)
 			usb_buffer_free(dev, URB_INT_SIZE, mc->data, mc->data_dma);
 		if (mc->dev)
diff --git a/drivers/usb/misc/usb_u132.h b/drivers/usb/misc/usb_u132.h
index 551ba89..dc2e5a3 100644
--- a/drivers/usb/misc/usb_u132.h
+++ b/drivers/usb/misc/usb_u132.h
@@ -52,7 +52,7 @@
 * the kernel to load the "u132-hcd" module.
 *
 * The "ftdi-u132" module provides the interface to the inserted
-* PC card and the "u132-hcd" module uses the API to send and recieve
+* PC card and the "u132-hcd" module uses the API to send and receive
 * data. The API features call-backs, so that part of the "u132-hcd"
 * module code will run in the context of one of the kernel threads
 * of the "ftdi-u132" module.
@@ -95,3 +95,7 @@
          int halted, int skipped, int actual, int non_null));
 int usb_ftdi_elan_edset_flush(struct platform_device *pdev, u8 ed_number,
         void *endp);
+int usb_ftdi_elan_read_pcimem(struct platform_device *pdev, int mem_offset,
+			      u8 width, u32 *data);
+int usb_ftdi_elan_write_pcimem(struct platform_device *pdev, int mem_offset,
+			       u8 width, u32 data);
diff --git a/drivers/usb/misc/usbtest.c b/drivers/usb/misc/usbtest.c
index 7c2cbdf..194065d 100644
--- a/drivers/usb/misc/usbtest.c
+++ b/drivers/usb/misc/usbtest.c
@@ -138,7 +138,7 @@
 			default:
 				continue;
 			}
-			if (e->desc.bEndpointAddress & USB_DIR_IN) {
+			if (usb_endpoint_dir_in(&e->desc)) {
 				if (!in)
 					in = e;
 			} else {
@@ -147,7 +147,7 @@
 			}
 			continue;
 try_iso:
-			if (e->desc.bEndpointAddress & USB_DIR_IN) {
+			if (usb_endpoint_dir_in(&e->desc)) {
 				if (!iso_in)
 					iso_in = e;
 			} else {
diff --git a/drivers/usb/net/asix.c b/drivers/usb/net/asix.c
index 881841e..95e682e 100644
--- a/drivers/usb/net/asix.c
+++ b/drivers/usb/net/asix.c
@@ -249,9 +249,9 @@
 
 	req->bRequestType = USB_DIR_OUT | USB_TYPE_VENDOR | USB_RECIP_DEVICE;
 	req->bRequest = cmd;
-	req->wValue = value;
-	req->wIndex = index;
-	req->wLength = size;
+	req->wValue = cpu_to_le16(value);
+	req->wIndex = cpu_to_le16(index);
+	req->wLength = cpu_to_le16(size);
 
 	usb_fill_control_urb(urb, dev->udev,
 			     usb_sndctrlpipe(dev->udev, 0),
diff --git a/drivers/usb/net/catc.c b/drivers/usb/net/catc.c
index f740325..907b820 100644
--- a/drivers/usb/net/catc.c
+++ b/drivers/usb/net/catc.c
@@ -786,14 +786,10 @@
 	if ((!catc->ctrl_urb) || (!catc->tx_urb) || 
 	    (!catc->rx_urb) || (!catc->irq_urb)) {
 		err("No free urbs available.");
-		if (catc->ctrl_urb)
-			usb_free_urb(catc->ctrl_urb);
-		if (catc->tx_urb)
-			usb_free_urb(catc->tx_urb);
-		if (catc->rx_urb)
-			usb_free_urb(catc->rx_urb);
-		if (catc->irq_urb)
-			usb_free_urb(catc->irq_urb);
+		usb_free_urb(catc->ctrl_urb);
+		usb_free_urb(catc->tx_urb);
+		usb_free_urb(catc->rx_urb);
+		usb_free_urb(catc->irq_urb);
 		free_netdev(netdev);
 		return -ENOMEM;
 	}
diff --git a/drivers/usb/net/cdc_ether.c b/drivers/usb/net/cdc_ether.c
index f6971b8..44a9154 100644
--- a/drivers/usb/net/cdc_ether.c
+++ b/drivers/usb/net/cdc_ether.c
@@ -200,8 +200,7 @@
 
 		dev->status = &info->control->cur_altsetting->endpoint [0];
 		desc = &dev->status->desc;
-		if (desc->bmAttributes != USB_ENDPOINT_XFER_INT
-				|| !(desc->bEndpointAddress & USB_DIR_IN)
+		if (!usb_endpoint_is_int_in(desc)
 				|| (le16_to_cpu(desc->wMaxPacketSize)
 					< sizeof(struct usb_cdc_notification))
 				|| !desc->bInterval) {
diff --git a/drivers/usb/net/net1080.c b/drivers/usb/net/net1080.c
index ce00de8..a774105 100644
--- a/drivers/usb/net/net1080.c
+++ b/drivers/usb/net/net1080.c
@@ -237,12 +237,12 @@
 #define	STATUS_CONN_OTHER	(1 << 14)
 #define	STATUS_SUSPEND_OTHER	(1 << 13)
 #define	STATUS_MAILBOX_OTHER	(1 << 12)
-#define	STATUS_PACKETS_OTHER(n)	(((n) >> 8) && 0x03)
+#define	STATUS_PACKETS_OTHER(n)	(((n) >> 8) & 0x03)
 
 #define	STATUS_CONN_THIS	(1 << 6)
 #define	STATUS_SUSPEND_THIS	(1 << 5)
 #define	STATUS_MAILBOX_THIS	(1 << 4)
-#define	STATUS_PACKETS_THIS(n)	(((n) >> 0) && 0x03)
+#define	STATUS_PACKETS_THIS(n)	(((n) >> 0) & 0x03)
 
 #define	STATUS_UNSPEC_MASK	0x0c8c
 #define	STATUS_NOISE_MASK 	((u16)~(0x0303|STATUS_UNSPEC_MASK))
diff --git a/drivers/usb/net/pegasus.c b/drivers/usb/net/pegasus.c
index 33abbd2..69eb0db 100644
--- a/drivers/usb/net/pegasus.c
+++ b/drivers/usb/net/pegasus.c
@@ -163,6 +163,7 @@
 
 	/* using ATOMIC, we'd never wake up if we slept */
 	if ((ret = usb_submit_urb(pegasus->ctrl_urb, GFP_ATOMIC))) {
+		set_current_state(TASK_RUNNING);
 		if (ret == -ENODEV)
 			netif_device_detach(pegasus->net);
 		if (netif_msg_drv(pegasus))
diff --git a/drivers/usb/net/usbnet.c b/drivers/usb/net/usbnet.c
index 760b532..7672e11 100644
--- a/drivers/usb/net/usbnet.c
+++ b/drivers/usb/net/usbnet.c
@@ -116,7 +116,7 @@
 			e = alt->endpoint + ep;
 			switch (e->desc.bmAttributes) {
 			case USB_ENDPOINT_XFER_INT:
-				if (!(e->desc.bEndpointAddress & USB_DIR_IN))
+				if (!usb_endpoint_dir_in(&e->desc))
 					continue;
 				intr = 1;
 				/* FALLTHROUGH */
@@ -125,7 +125,7 @@
 			default:
 				continue;
 			}
-			if (e->desc.bEndpointAddress & USB_DIR_IN) {
+			if (usb_endpoint_dir_in(&e->desc)) {
 				if (!intr && !in)
 					in = e;
 				else if (intr && !status)
diff --git a/drivers/usb/serial/Kconfig b/drivers/usb/serial/Kconfig
index 2a8dd4c..2f4d303 100644
--- a/drivers/usb/serial/Kconfig
+++ b/drivers/usb/serial/Kconfig
@@ -554,6 +554,17 @@
 	  To compile this driver as a module, choose M here: the
 	  module will be called omninet.
 
+config USB_SERIAL_DEBUG
+	tristate "USB Debugging Device"
+	depends on USB_SERIAL
+	help
+	  Say Y here if you have a USB debugging device used to recieve
+	  debugging data from another machine.  The most common of these
+	  devices is the NetChip TurboCONNECT device.
+
+	  To compile this driver as a module, choose M here: the
+	  module will be called usb-debug.
+
 config USB_EZUSB
 	bool
 	depends on USB_SERIAL_KEYSPAN_PDA || USB_SERIAL_XIRCOM || USB_SERIAL_KEYSPAN || USB_SERIAL_WHITEHEAT
diff --git a/drivers/usb/serial/Makefile b/drivers/usb/serial/Makefile
index a5047dc..61166ad 100644
--- a/drivers/usb/serial/Makefile
+++ b/drivers/usb/serial/Makefile
@@ -18,6 +18,7 @@
 obj-$(CONFIG_USB_SERIAL_CP2101)			+= cp2101.o
 obj-$(CONFIG_USB_SERIAL_CYBERJACK)		+= cyberjack.o
 obj-$(CONFIG_USB_SERIAL_CYPRESS_M8)		+= cypress_m8.o
+obj-$(CONFIG_USB_SERIAL_DEBUG)			+= usb_debug.o
 obj-$(CONFIG_USB_SERIAL_DIGI_ACCELEPORT)	+= digi_acceleport.o
 obj-$(CONFIG_USB_SERIAL_EDGEPORT)		+= io_edgeport.o
 obj-$(CONFIG_USB_SERIAL_EDGEPORT_TI)		+= io_ti.o
diff --git a/drivers/usb/serial/aircable.c b/drivers/usb/serial/aircable.c
index 8122755..b1b5707 100644
--- a/drivers/usb/serial/aircable.c
+++ b/drivers/usb/serial/aircable.c
@@ -270,8 +270,11 @@
 	 */
 	tty = port->tty;
 
-	if (!tty)
+	if (!tty) {
 		schedule_work(&priv->rx_work);
+		err("%s - No tty available", __FUNCTION__);
+		return ;
+	}
 
 	count = min(64, serial_buf_data_avail(priv->rx_buf));
 
@@ -305,9 +308,7 @@
 
 	for (i = 0; i < iface_desc->desc.bNumEndpoints; i++) {
 		endpoint = &iface_desc->endpoint[i].desc;
-		if (((endpoint->bEndpointAddress & 0x80) == 0x00) &&
-			((endpoint->bmAttributes & 3) == 0x02)) {
-			/* we found our bulk out endpoint */
+		if (usb_endpoint_is_bulk_out(endpoint)) {
 			dbg("found bulk out on endpoint %d", i);
 			++num_bulk_out;
 		}
diff --git a/drivers/usb/serial/airprime.c b/drivers/usb/serial/airprime.c
index 7f5d546..96c7372 100644
--- a/drivers/usb/serial/airprime.c
+++ b/drivers/usb/serial/airprime.c
@@ -19,6 +19,7 @@
 static struct usb_device_id id_table [] = {
 	{ USB_DEVICE(0x0c88, 0x17da) }, /* Kyocera Wireless KPC650/Passport */
 	{ USB_DEVICE(0x1410, 0x1110) }, /* Novatel Wireless Merlin CDMA */
+	{ USB_DEVICE(0x1410, 0x1430) },	/* Novatel Merlin XU870 HSDPA/3G */
 	{ USB_DEVICE(0x1410, 0x1100) }, /* ExpressCard34 Qualcomm 3G CDMA */
 	{ },
 };
diff --git a/drivers/usb/serial/ark3116.c b/drivers/usb/serial/ark3116.c
index ca52f12..863966c 100644
--- a/drivers/usb/serial/ark3116.c
+++ b/drivers/usb/serial/ark3116.c
@@ -85,10 +85,9 @@
 	int i;
 
 	for (i = 0; i < serial->num_ports; ++i) {
-		priv = kmalloc(sizeof (struct ark3116_private), GFP_KERNEL);
+		priv = kzalloc(sizeof(struct ark3116_private), GFP_KERNEL);
 		if (!priv)
 			goto cleanup;
-		memset(priv, 0x00, sizeof (struct ark3116_private));
 		spin_lock_init(&priv->lock);
 
 		usb_set_serial_port_data(serial->port[i], priv);
diff --git a/drivers/usb/serial/console.c b/drivers/usb/serial/console.c
index 3a9073d..7167728 100644
--- a/drivers/usb/serial/console.c
+++ b/drivers/usb/serial/console.c
@@ -166,19 +166,17 @@
 	if (serial->type->set_termios) {
 		/* build up a fake tty structure so that the open call has something
 		 * to look at to get the cflag value */
-		tty = kmalloc (sizeof (*tty), GFP_KERNEL);
+		tty = kzalloc(sizeof(*tty), GFP_KERNEL);
 		if (!tty) {
 			err ("no more memory");
 			return -ENOMEM;
 		}
-		termios = kmalloc (sizeof (*termios), GFP_KERNEL);
+		termios = kzalloc(sizeof(*termios), GFP_KERNEL);
 		if (!termios) {
 			err ("no more memory");
 			kfree (tty);
 			return -ENOMEM;
 		}
-		memset (tty, 0x00, sizeof(*tty));
-		memset (termios, 0x00, sizeof(*termios));
 		termios->c_cflag = cflag;
 		tty->termios = termios;
 		port->tty = tty;
diff --git a/drivers/usb/serial/cypress_m8.c b/drivers/usb/serial/cypress_m8.c
index f2e89a0..093f303 100644
--- a/drivers/usb/serial/cypress_m8.c
+++ b/drivers/usb/serial/cypress_m8.c
@@ -1684,15 +1684,14 @@
 
 	info(DRIVER_DESC " " DRIVER_VERSION);
 	return 0;
-failed_usb_register:
-	usb_deregister(&cypress_driver);
-failed_ca42v2_register:
-	usb_serial_deregister(&cypress_ca42v2_device);
-failed_hidcom_register:
-	usb_serial_deregister(&cypress_hidcom_device);
-failed_em_register:
-	usb_serial_deregister(&cypress_earthmate_device);
 
+failed_usb_register:
+	usb_serial_deregister(&cypress_ca42v2_device);
+failed_ca42v2_register:
+	usb_serial_deregister(&cypress_hidcom_device);
+failed_hidcom_register:
+	usb_serial_deregister(&cypress_earthmate_device);
+failed_em_register:
 	return retval;
 }
 
diff --git a/drivers/usb/serial/digi_acceleport.c b/drivers/usb/serial/digi_acceleport.c
index bdb5810..5e3ac28 100644
--- a/drivers/usb/serial/digi_acceleport.c
+++ b/drivers/usb/serial/digi_acceleport.c
@@ -157,7 +157,7 @@
 *       to TASK_RUNNING will be lost and write_chan's subsequent call to
 *       schedule() will never return (unless it catches a signal).
 *       This race condition occurs because write_bulk_callback() (and thus
-*       the wakeup) are called asynchonously from an interrupt, rather than
+*       the wakeup) are called asynchronously from an interrupt, rather than
 *       from the scheduler.  We can avoid the race by calling the wakeup
 *       from the scheduler queue and that's our fix:  Now, at the end of
 *       write_bulk_callback() we queue up a wakeup call on the scheduler
diff --git a/drivers/usb/serial/ezusb.c b/drivers/usb/serial/ezusb.c
index 5169c2d..97ee718 100644
--- a/drivers/usb/serial/ezusb.c
+++ b/drivers/usb/serial/ezusb.c
@@ -31,12 +31,11 @@
 		return -ENODEV;
 	}
 
-	transfer_buffer =  kmalloc (length, GFP_KERNEL);
+	transfer_buffer = kmemdup(data, length, GFP_KERNEL);
 	if (!transfer_buffer) {
 		dev_err(&serial->dev->dev, "%s - kmalloc(%d) failed.\n", __FUNCTION__, length);
 		return -ENOMEM;
 	}
-	memcpy (transfer_buffer, data, length);
 	result = usb_control_msg (serial->dev, usb_sndctrlpipe(serial->dev, 0), bRequest, 0x40, address, 0, transfer_buffer, length, 3000);
 	kfree (transfer_buffer);
 	return result;
diff --git a/drivers/usb/serial/ftdi_sio.c b/drivers/usb/serial/ftdi_sio.c
index c186b4e..89ce277 100644
--- a/drivers/usb/serial/ftdi_sio.c
+++ b/drivers/usb/serial/ftdi_sio.c
@@ -1388,8 +1388,7 @@
 	flush_scheduled_work();
 
 	/* shutdown our bulk read */
-	if (port->read_urb)
-		usb_kill_urb(port->read_urb);
+	usb_kill_urb(port->read_urb);
 } /* ftdi_close */
 
 
diff --git a/drivers/usb/serial/garmin_gps.c b/drivers/usb/serial/garmin_gps.c
index 4543152..6530d39 100644
--- a/drivers/usb/serial/garmin_gps.c
+++ b/drivers/usb/serial/garmin_gps.c
@@ -1523,12 +1523,11 @@
 
 	dbg("%s", __FUNCTION__);
 
-	garmin_data_p = kmalloc (sizeof(struct garmin_data), GFP_KERNEL);
+	garmin_data_p = kzalloc(sizeof(struct garmin_data), GFP_KERNEL);
 	if (garmin_data_p == NULL) {
 		dev_err(&port->dev, "%s - Out of memory\n", __FUNCTION__);
 		return -ENOMEM;
 	}
-	memset (garmin_data_p, 0, sizeof(struct garmin_data));
 	init_timer(&garmin_data_p->timer);
 	spin_lock_init(&garmin_data_p->lock);
 	INIT_LIST_HEAD(&garmin_data_p->pktlist);
diff --git a/drivers/usb/serial/io_edgeport.c b/drivers/usb/serial/io_edgeport.c
index 91bd301..d06547a 100644
--- a/drivers/usb/serial/io_edgeport.c
+++ b/drivers/usb/serial/io_edgeport.c
@@ -1038,9 +1038,7 @@
 	edge_port->open = FALSE;
 	edge_port->openPending = FALSE;
 
-	if (edge_port->write_urb) {
-		usb_kill_urb(edge_port->write_urb);
-	}
+	usb_kill_urb(edge_port->write_urb);
 
 	if (edge_port->write_urb) {
 		/* if this urb had a transfer buffer already (old transfer) free it */
diff --git a/drivers/usb/serial/ipw.c b/drivers/usb/serial/ipw.c
index 2a4bb66..d3b9a35 100644
--- a/drivers/usb/serial/ipw.c
+++ b/drivers/usb/serial/ipw.c
@@ -206,10 +206,9 @@
 
 	dbg("%s", __FUNCTION__);
 
-	buf_flow_init = kmalloc(16, GFP_KERNEL);
+	buf_flow_init = kmemdup(buf_flow_static, 16, GFP_KERNEL);
 	if (!buf_flow_init)
 		return -ENOMEM;
-	memcpy(buf_flow_init, buf_flow_static, 16);
 
 	if (port->tty)
 		port->tty->low_latency = 1;
diff --git a/drivers/usb/serial/keyspan.c b/drivers/usb/serial/keyspan.c
index 53be824..7639652 100644
--- a/drivers/usb/serial/keyspan.c
+++ b/drivers/usb/serial/keyspan.c
@@ -2306,22 +2306,16 @@
 	}
 
 	/* Now free them */
-	if (s_priv->instat_urb)
-		usb_free_urb(s_priv->instat_urb);
-	if (s_priv->glocont_urb)
-		usb_free_urb(s_priv->glocont_urb);
+	usb_free_urb(s_priv->instat_urb);
+	usb_free_urb(s_priv->glocont_urb);
 	for (i = 0; i < serial->num_ports; ++i) {
 		port = serial->port[i];
 		p_priv = usb_get_serial_port_data(port);
-		if (p_priv->inack_urb)
-			usb_free_urb(p_priv->inack_urb);
-		if (p_priv->outcont_urb)
-			usb_free_urb(p_priv->outcont_urb);
+		usb_free_urb(p_priv->inack_urb);
+		usb_free_urb(p_priv->outcont_urb);
 		for (j = 0; j < 2; j++) {
-			if (p_priv->in_urbs[j])
-				usb_free_urb(p_priv->in_urbs[j]);
-			if (p_priv->out_urbs[j])
-				usb_free_urb(p_priv->out_urbs[j]);
+			usb_free_urb(p_priv->in_urbs[j]);
+			usb_free_urb(p_priv->out_urbs[j]);
 		}
 	}
 
diff --git a/drivers/usb/serial/kobil_sct.c b/drivers/usb/serial/kobil_sct.c
index ff03331..2372899 100644
--- a/drivers/usb/serial/kobil_sct.c
+++ b/drivers/usb/serial/kobil_sct.c
@@ -185,13 +185,11 @@
   
  	for (i = 0; i < altsetting->desc.bNumEndpoints; i++) {
 		endpoint = &altsetting->endpoint[i];
-		if (((endpoint->desc.bEndpointAddress & USB_ENDPOINT_DIR_MASK) == USB_DIR_OUT) && 
- 		    ((endpoint->desc.bmAttributes & USB_ENDPOINT_XFERTYPE_MASK) == USB_ENDPOINT_XFER_INT)) {
+		if (usb_endpoint_is_int_out(&endpoint->desc)) {
 		 	dbg("%s Found interrupt out endpoint. Address: %d", __FUNCTION__, endpoint->desc.bEndpointAddress);
 		 	priv->write_int_endpoint_address = endpoint->desc.bEndpointAddress;
  		}
- 		if (((endpoint->desc.bEndpointAddress & USB_ENDPOINT_DIR_MASK) == USB_DIR_IN) && 
- 		    ((endpoint->desc.bmAttributes & USB_ENDPOINT_XFERTYPE_MASK) == USB_ENDPOINT_XFER_INT)) {
+		if (usb_endpoint_is_int_in(&endpoint->desc)) {
 		 	dbg("%s Found interrupt in  endpoint. Address: %d", __FUNCTION__, endpoint->desc.bEndpointAddress);
 		 	priv->read_int_endpoint_address = endpoint->desc.bEndpointAddress;
 	 	}
@@ -355,8 +353,7 @@
 		usb_free_urb( port->write_urb );
 		port->write_urb = NULL;
 	}
-	if (port->interrupt_in_urb)
-		usb_kill_urb(port->interrupt_in_urb);
+	usb_kill_urb(port->interrupt_in_urb);
 }
 
 
diff --git a/drivers/usb/serial/mct_u232.c b/drivers/usb/serial/mct_u232.c
index b7582cc..a906e50 100644
--- a/drivers/usb/serial/mct_u232.c
+++ b/drivers/usb/serial/mct_u232.c
@@ -358,10 +358,8 @@
 	/* Puh, that's dirty */
 	port = serial->port[0];
 	rport = serial->port[1];
-	if (port->read_urb) {
-		/* No unlinking, it wasn't submitted yet. */
-		usb_free_urb(port->read_urb);
-	}
+	/* No unlinking, it wasn't submitted yet. */
+	usb_free_urb(port->read_urb);
 	port->read_urb = rport->interrupt_in_urb;
 	rport->interrupt_in_urb = NULL;
 	port->read_urb->context = port;
diff --git a/drivers/usb/serial/mos7840.c b/drivers/usb/serial/mos7840.c
index 5b71962..02c89e1 100644
--- a/drivers/usb/serial/mos7840.c
+++ b/drivers/usb/serial/mos7840.c
@@ -2596,12 +2596,11 @@
 
 	/* set up port private structures */
 	for (i = 0; i < serial->num_ports; ++i) {
-		mos7840_port = kmalloc(sizeof(struct moschip_port), GFP_KERNEL);
+		mos7840_port = kzalloc(sizeof(struct moschip_port), GFP_KERNEL);
 		if (mos7840_port == NULL) {
 			err("%s - Out of memory", __FUNCTION__);
 			return -ENOMEM;
 		}
-		memset(mos7840_port, 0, sizeof(struct moschip_port));
 
 		/* Initialize all port interrupt end point to port 0 int endpoint *
 		 * Our device has only one interrupt end point comman to all port */
diff --git a/drivers/usb/serial/navman.c b/drivers/usb/serial/navman.c
index 0610409..054abee 100644
--- a/drivers/usb/serial/navman.c
+++ b/drivers/usb/serial/navman.c
@@ -95,8 +95,7 @@
 {
 	dbg("%s - port %d", __FUNCTION__, port->number);
 
-	if (port->interrupt_in_urb)
-		usb_kill_urb(port->interrupt_in_urb);
+	usb_kill_urb(port->interrupt_in_urb);
 }
 
 static int navman_write(struct usb_serial_port *port,
diff --git a/drivers/usb/serial/ti_usb_3410_5052.c b/drivers/usb/serial/ti_usb_3410_5052.c
index 07400c0..ae98d8c 100644
--- a/drivers/usb/serial/ti_usb_3410_5052.c
+++ b/drivers/usb/serial/ti_usb_3410_5052.c
@@ -228,6 +228,7 @@
 /* null entry */
 static struct usb_device_id ti_id_table_3410[1+TI_EXTRA_VID_PID_COUNT+1] = {
 	{ USB_DEVICE(TI_VENDOR_ID, TI_3410_PRODUCT_ID) },
+	{ USB_DEVICE(TI_VENDOR_ID, TI_3410_EZ430_ID) },
 };
 
 static struct usb_device_id ti_id_table_5052[4+TI_EXTRA_VID_PID_COUNT+1] = {
@@ -239,6 +240,7 @@
 
 static struct usb_device_id ti_id_table_combined[] = {
 	{ USB_DEVICE(TI_VENDOR_ID, TI_3410_PRODUCT_ID) },
+	{ USB_DEVICE(TI_VENDOR_ID, TI_3410_EZ430_ID) },
 	{ USB_DEVICE(TI_VENDOR_ID, TI_5052_BOOT_PRODUCT_ID) },
 	{ USB_DEVICE(TI_VENDOR_ID, TI_5152_BOOT_PRODUCT_ID) },
 	{ USB_DEVICE(TI_VENDOR_ID, TI_5052_EEPROM_PRODUCT_ID) },
@@ -459,13 +461,12 @@
 
 	/* set up port structures */
 	for (i = 0; i < serial->num_ports; ++i) {
-		tport = kmalloc(sizeof(struct ti_port), GFP_KERNEL);
+		tport = kzalloc(sizeof(struct ti_port), GFP_KERNEL);
 		if (tport == NULL) {
 			dev_err(&dev->dev, "%s - out of memory\n", __FUNCTION__);
 			status = -ENOMEM;
 			goto free_tports;
 		}
-		memset(tport, 0, sizeof(struct ti_port));
 		spin_lock_init(&tport->tp_lock);
 		tport->tp_uart_base_addr = (i == 0 ? TI_UART1_BASE_ADDR : TI_UART2_BASE_ADDR);
 		tport->tp_flags = low_latency ? ASYNC_LOW_LATENCY : 0;
diff --git a/drivers/usb/serial/ti_usb_3410_5052.h b/drivers/usb/serial/ti_usb_3410_5052.h
index 02c1aeb..b5541bf 100644
--- a/drivers/usb/serial/ti_usb_3410_5052.h
+++ b/drivers/usb/serial/ti_usb_3410_5052.h
@@ -28,6 +28,7 @@
 /* Vendor and product ids */
 #define TI_VENDOR_ID			0x0451
 #define TI_3410_PRODUCT_ID		0x3410
+#define TI_3410_EZ430_ID		0xF430  /* TI ez430 development tool */
 #define TI_5052_BOOT_PRODUCT_ID		0x5052	/* no EEPROM, no firmware */
 #define TI_5152_BOOT_PRODUCT_ID		0x5152	/* no EEPROM, no firmware */
 #define TI_5052_EEPROM_PRODUCT_ID	0x505A	/* EEPROM, no firmware */
diff --git a/drivers/usb/serial/usb-serial.c b/drivers/usb/serial/usb-serial.c
index 8006e51..c1257d5 100644
--- a/drivers/usb/serial/usb-serial.c
+++ b/drivers/usb/serial/usb-serial.c
@@ -952,32 +952,28 @@
 		port = serial->port[i];
 		if (!port)
 			continue;
-		if (port->read_urb)
-			usb_free_urb (port->read_urb);
+		usb_free_urb(port->read_urb);
 		kfree(port->bulk_in_buffer);
 	}
 	for (i = 0; i < num_bulk_out; ++i) {
 		port = serial->port[i];
 		if (!port)
 			continue;
-		if (port->write_urb)
-			usb_free_urb (port->write_urb);
+		usb_free_urb(port->write_urb);
 		kfree(port->bulk_out_buffer);
 	}
 	for (i = 0; i < num_interrupt_in; ++i) {
 		port = serial->port[i];
 		if (!port)
 			continue;
-		if (port->interrupt_in_urb)
-			usb_free_urb (port->interrupt_in_urb);
+		usb_free_urb(port->interrupt_in_urb);
 		kfree(port->interrupt_in_buffer);
 	}
 	for (i = 0; i < num_interrupt_out; ++i) {
 		port = serial->port[i];
 		if (!port)
 			continue;
-		if (port->interrupt_out_urb)
-			usb_free_urb (port->interrupt_out_urb);
+		usb_free_urb(port->interrupt_out_urb);
 		kfree(port->interrupt_out_buffer);
 	}
 
diff --git a/drivers/usb/serial/usb_debug.c b/drivers/usb/serial/usb_debug.c
new file mode 100644
index 0000000..257a5e4
--- /dev/null
+++ b/drivers/usb/serial/usb_debug.c
@@ -0,0 +1,65 @@
+/*
+ * USB Debug cable driver
+ *
+ * Copyright (C) 2006 Greg Kroah-Hartman <greg@kroah.com>
+ *
+ *	This program is free software; you can redistribute it and/or
+ *	modify it under the terms of the GNU General Public License version
+ *	2 as published by the Free Software Foundation.
+ */
+
+#include <linux/kernel.h>
+#include <linux/init.h>
+#include <linux/tty.h>
+#include <linux/module.h>
+#include <linux/usb.h>
+#include <linux/usb/serial.h>
+
+static struct usb_device_id id_table [] = {
+	{ USB_DEVICE(0x0525, 0x127a) },
+	{ },
+};
+MODULE_DEVICE_TABLE(usb, id_table);
+
+static struct usb_driver debug_driver = {
+	.name =		"debug",
+	.probe =	usb_serial_probe,
+	.disconnect =	usb_serial_disconnect,
+	.id_table =	id_table,
+	.no_dynamic_id = 	1,
+};
+
+static struct usb_serial_driver debug_device = {
+	.driver = {
+		.owner =	THIS_MODULE,
+		.name =		"debug",
+	},
+	.id_table =		id_table,
+	.num_interrupt_in =	NUM_DONT_CARE,
+	.num_bulk_in =		NUM_DONT_CARE,
+	.num_bulk_out =		NUM_DONT_CARE,
+	.num_ports =		1,
+};
+
+static int __init debug_init(void)
+{
+	int retval;
+
+	retval = usb_serial_register(&debug_device);
+	if (retval)
+		return retval;
+	retval = usb_register(&debug_driver);
+	if (retval)
+		usb_serial_deregister(&debug_device);
+	return retval;
+}
+
+static void __exit debug_exit(void)
+{
+	usb_deregister(&debug_driver);
+	usb_serial_deregister(&debug_device);
+}
+
+module_init(debug_init);
+module_exit(debug_exit);
+MODULE_LICENSE("GPL");
diff --git a/drivers/usb/serial/visor.c b/drivers/usb/serial/visor.c
index befe2e1..eef5eaa 100644
--- a/drivers/usb/serial/visor.c
+++ b/drivers/usb/serial/visor.c
@@ -348,8 +348,7 @@
 			 
 	/* shutdown our urbs */
 	usb_kill_urb(port->read_urb);
-	if (port->interrupt_in_urb)
-		usb_kill_urb(port->interrupt_in_urb);
+	usb_kill_urb(port->interrupt_in_urb);
 
 	/* Try to send shutdown message, if the device is gone, this will just fail. */
 	transfer_buffer =  kmalloc (0x12, GFP_KERNEL);
diff --git a/drivers/usb/storage/onetouch.c b/drivers/usb/storage/onetouch.c
index 3baf448..3a158d5 100644
--- a/drivers/usb/storage/onetouch.c
+++ b/drivers/usb/storage/onetouch.c
@@ -142,10 +142,7 @@
 		return -ENODEV;
 
 	endpoint = &interface->endpoint[2].desc;
-	if (!(endpoint->bEndpointAddress & USB_DIR_IN))
-		return -ENODEV;
-	if ((endpoint->bmAttributes & USB_ENDPOINT_XFERTYPE_MASK)
-			!= USB_ENDPOINT_XFER_INT)
+	if (!usb_endpoint_is_int_in(endpoint))
 		return -ENODEV;
 
 	pipe = usb_rcvintpipe(udev, endpoint->bEndpointAddress);
diff --git a/drivers/usb/storage/unusual_devs.h b/drivers/usb/storage/unusual_devs.h
index efb047f..db8b260 100644
--- a/drivers/usb/storage/unusual_devs.h
+++ b/drivers/usb/storage/unusual_devs.h
@@ -1318,6 +1318,16 @@
 		US_SC_DEVICE, US_PR_DEVICE, usb_stor_ucr61s2b_init,
 		0 ),
 
+/* Reported by Jaco Kroon <jaco@kroon.co.za>
+ * The usb-storage module found on the Digitech GNX4 (and supposedly other
+ * devices) misbehaves and causes a bunch of invalid I/O errors.
+ */
+UNUSUAL_DEV(  0x1210, 0x0003, 0x0100, 0x0100,
+		"Digitech HMG",
+		"DigiTech Mass Storage",
+		US_SC_DEVICE, US_PR_DEVICE, NULL,
+		US_FL_IGNORE_RESIDUE ),
+
 /* Reported by Vilius Bilinkevicius <vilisas AT xxx DOT lt) */
 UNUSUAL_DEV(  0x132b, 0x000b, 0x0001, 0x0001,
 		"Minolta",
diff --git a/drivers/usb/storage/usb.c b/drivers/usb/storage/usb.c
index b8d6031..b401084 100644
--- a/drivers/usb/storage/usb.c
+++ b/drivers/usb/storage/usb.c
@@ -740,18 +740,16 @@
 		ep = &altsetting->endpoint[i].desc;
 
 		/* Is it a BULK endpoint? */
-		if ((ep->bmAttributes & USB_ENDPOINT_XFERTYPE_MASK)
-				== USB_ENDPOINT_XFER_BULK) {
+		if (usb_endpoint_xfer_bulk(ep)) {
 			/* BULK in or out? */
-			if (ep->bEndpointAddress & USB_DIR_IN)
+			if (usb_endpoint_dir_in(ep))
 				ep_in = ep;
 			else
 				ep_out = ep;
 		}
 
 		/* Is it an interrupt endpoint? */
-		else if ((ep->bmAttributes & USB_ENDPOINT_XFERTYPE_MASK)
-				== USB_ENDPOINT_XFER_INT) {
+		else if (usb_endpoint_xfer_int(ep)) {
 			ep_int = ep;
 		}
 	}
diff --git a/drivers/video/fbmem.c b/drivers/video/fbmem.c
index 93ffcdd..e973a87 100644
--- a/drivers/video/fbmem.c
+++ b/drivers/video/fbmem.c
@@ -1296,14 +1296,14 @@
 			break;
 	fb_info->node = i;
 
-	fb_info->class_device = class_device_create(fb_class, NULL, MKDEV(FB_MAJOR, i),
-				    fb_info->device, "fb%d", i);
-	if (IS_ERR(fb_info->class_device)) {
+	fb_info->dev = device_create(fb_class, fb_info->device,
+				     MKDEV(FB_MAJOR, i), "fb%d", i);
+	if (IS_ERR(fb_info->dev)) {
 		/* Not fatal */
-		printk(KERN_WARNING "Unable to create class_device for framebuffer %d; errno = %ld\n", i, PTR_ERR(fb_info->class_device));
-		fb_info->class_device = NULL;
+		printk(KERN_WARNING "Unable to create device for framebuffer %d; errno = %ld\n", i, PTR_ERR(fb_info->dev));
+		fb_info->dev = NULL;
 	} else
-		fb_init_class_device(fb_info);
+		fb_init_device(fb_info);
 
 	if (fb_info->pixmap.addr == NULL) {
 		fb_info->pixmap.addr = kmalloc(FBPIXMAPSIZE, GFP_KERNEL);
@@ -1356,8 +1356,8 @@
 	fb_destroy_modelist(&fb_info->modelist);
 	registered_fb[i]=NULL;
 	num_registered_fb--;
-	fb_cleanup_class_device(fb_info);
-	class_device_destroy(fb_class, MKDEV(FB_MAJOR, i));
+	fb_cleanup_device(fb_info);
+	device_destroy(fb_class, MKDEV(FB_MAJOR, i));
 	event.info = fb_info;
 	fb_notifier_call_chain(FB_EVENT_FB_UNREGISTERED, &event);
 	return 0;
diff --git a/drivers/video/fbsysfs.c b/drivers/video/fbsysfs.c
index d3a5041..323bdf6 100644
--- a/drivers/video/fbsysfs.c
+++ b/drivers/video/fbsysfs.c
@@ -73,7 +73,7 @@
  *
  * @info: frame buffer info structure
  *
- * Drop the reference count of the class_device embedded in the
+ * Drop the reference count of the device embedded in the
  * framebuffer info structure.
  *
  */
@@ -120,10 +120,10 @@
 	                m, mode->xres, mode->yres, v, mode->refresh);
 }
 
-static ssize_t store_mode(struct class_device *class_device, const char * buf,
-			  size_t count)
+static ssize_t store_mode(struct device *device, struct device_attribute *attr,
+			  const char *buf, size_t count)
 {
-	struct fb_info *fb_info = class_get_devdata(class_device);
+	struct fb_info *fb_info = dev_get_drvdata(device);
 	char mstr[100];
 	struct fb_var_screeninfo var;
 	struct fb_modelist *modelist;
@@ -151,9 +151,10 @@
 	return -EINVAL;
 }
 
-static ssize_t show_mode(struct class_device *class_device, char *buf)
+static ssize_t show_mode(struct device *device, struct device_attribute *attr,
+			 char *buf)
 {
-	struct fb_info *fb_info = class_get_devdata(class_device);
+	struct fb_info *fb_info = dev_get_drvdata(device);
 
 	if (!fb_info->mode)
 		return 0;
@@ -161,10 +162,11 @@
 	return mode_string(buf, 0, fb_info->mode);
 }
 
-static ssize_t store_modes(struct class_device *class_device, const char * buf,
-			   size_t count)
+static ssize_t store_modes(struct device *device,
+			   struct device_attribute *attr,
+			   const char *buf, size_t count)
 {
-	struct fb_info *fb_info = class_get_devdata(class_device);
+	struct fb_info *fb_info = dev_get_drvdata(device);
 	LIST_HEAD(old_list);
 	int i = count / sizeof(struct fb_videomode);
 
@@ -186,9 +188,10 @@
 	return 0;
 }
 
-static ssize_t show_modes(struct class_device *class_device, char *buf)
+static ssize_t show_modes(struct device *device, struct device_attribute *attr,
+			  char *buf)
 {
-	struct fb_info *fb_info = class_get_devdata(class_device);
+	struct fb_info *fb_info = dev_get_drvdata(device);
 	unsigned int i;
 	struct list_head *pos;
 	struct fb_modelist *modelist;
@@ -203,10 +206,10 @@
 	return i;
 }
 
-static ssize_t store_bpp(struct class_device *class_device, const char * buf,
-			 size_t count)
+static ssize_t store_bpp(struct device *device, struct device_attribute *attr,
+			 const char *buf, size_t count)
 {
-	struct fb_info *fb_info = class_get_devdata(class_device);
+	struct fb_info *fb_info = dev_get_drvdata(device);
 	struct fb_var_screeninfo var;
 	char ** last = NULL;
 	int err;
@@ -218,16 +221,18 @@
 	return count;
 }
 
-static ssize_t show_bpp(struct class_device *class_device, char *buf)
+static ssize_t show_bpp(struct device *device, struct device_attribute *attr,
+			char *buf)
 {
-	struct fb_info *fb_info = class_get_devdata(class_device);
+	struct fb_info *fb_info = dev_get_drvdata(device);
 	return snprintf(buf, PAGE_SIZE, "%d\n", fb_info->var.bits_per_pixel);
 }
 
-static ssize_t store_rotate(struct class_device *class_device, const char *buf,
-			    size_t count)
+static ssize_t store_rotate(struct device *device,
+			    struct device_attribute *attr,
+			    const char *buf, size_t count)
 {
-	struct fb_info *fb_info = class_get_devdata(class_device);
+	struct fb_info *fb_info = dev_get_drvdata(device);
 	struct fb_var_screeninfo var;
 	char **last = NULL;
 	int err;
@@ -242,17 +247,19 @@
 }
 
 
-static ssize_t show_rotate(struct class_device *class_device, char *buf)
+static ssize_t show_rotate(struct device *device,
+			   struct device_attribute *attr, char *buf)
 {
-	struct fb_info *fb_info = class_get_devdata(class_device);
+	struct fb_info *fb_info = dev_get_drvdata(device);
 
 	return snprintf(buf, PAGE_SIZE, "%d\n", fb_info->var.rotate);
 }
 
-static ssize_t store_virtual(struct class_device *class_device,
-			     const char * buf, size_t count)
+static ssize_t store_virtual(struct device *device,
+			     struct device_attribute *attr,
+			     const char *buf, size_t count)
 {
-	struct fb_info *fb_info = class_get_devdata(class_device);
+	struct fb_info *fb_info = dev_get_drvdata(device);
 	struct fb_var_screeninfo var;
 	char *last = NULL;
 	int err;
@@ -269,23 +276,26 @@
 	return count;
 }
 
-static ssize_t show_virtual(struct class_device *class_device, char *buf)
+static ssize_t show_virtual(struct device *device,
+			    struct device_attribute *attr, char *buf)
 {
-	struct fb_info *fb_info = class_get_devdata(class_device);
+	struct fb_info *fb_info = dev_get_drvdata(device);
 	return snprintf(buf, PAGE_SIZE, "%d,%d\n", fb_info->var.xres_virtual,
 			fb_info->var.yres_virtual);
 }
 
-static ssize_t show_stride(struct class_device *class_device, char *buf)
+static ssize_t show_stride(struct device *device,
+			   struct device_attribute *attr, char *buf)
 {
-	struct fb_info *fb_info = class_get_devdata(class_device);
+	struct fb_info *fb_info = dev_get_drvdata(device);
 	return snprintf(buf, PAGE_SIZE, "%d\n", fb_info->fix.line_length);
 }
 
-static ssize_t store_blank(struct class_device *class_device, const char * buf,
-			   size_t count)
+static ssize_t store_blank(struct device *device,
+			   struct device_attribute *attr,
+			   const char *buf, size_t count)
 {
-	struct fb_info *fb_info = class_get_devdata(class_device);
+	struct fb_info *fb_info = dev_get_drvdata(device);
 	char *last = NULL;
 	int err;
 
@@ -299,42 +309,48 @@
 	return count;
 }
 
-static ssize_t show_blank(struct class_device *class_device, char *buf)
+static ssize_t show_blank(struct device *device,
+			  struct device_attribute *attr, char *buf)
 {
-//	struct fb_info *fb_info = class_get_devdata(class_device);
+//	struct fb_info *fb_info = dev_get_drvdata(device);
 	return 0;
 }
 
-static ssize_t store_console(struct class_device *class_device,
-			     const char * buf, size_t count)
+static ssize_t store_console(struct device *device,
+			     struct device_attribute *attr,
+			     const char *buf, size_t count)
 {
-//	struct fb_info *fb_info = class_get_devdata(class_device);
+//	struct fb_info *fb_info = dev_get_drvdata(device);
 	return 0;
 }
 
-static ssize_t show_console(struct class_device *class_device, char *buf)
+static ssize_t show_console(struct device *device,
+			    struct device_attribute *attr, char *buf)
 {
-//	struct fb_info *fb_info = class_get_devdata(class_device);
+//	struct fb_info *fb_info = dev_get_drvdata(device);
 	return 0;
 }
 
-static ssize_t store_cursor(struct class_device *class_device,
-			    const char * buf, size_t count)
+static ssize_t store_cursor(struct device *device,
+			    struct device_attribute *attr,
+			    const char *buf, size_t count)
 {
-//	struct fb_info *fb_info = class_get_devdata(class_device);
+//	struct fb_info *fb_info = dev_get_drvdata(device);
 	return 0;
 }
 
-static ssize_t show_cursor(struct class_device *class_device, char *buf)
+static ssize_t show_cursor(struct device *device,
+			   struct device_attribute *attr, char *buf)
 {
-//	struct fb_info *fb_info = class_get_devdata(class_device);
+//	struct fb_info *fb_info = dev_get_drvdata(device);
 	return 0;
 }
 
-static ssize_t store_pan(struct class_device *class_device, const char * buf,
-			 size_t count)
+static ssize_t store_pan(struct device *device,
+			 struct device_attribute *attr,
+			 const char *buf, size_t count)
 {
-	struct fb_info *fb_info = class_get_devdata(class_device);
+	struct fb_info *fb_info = dev_get_drvdata(device);
 	struct fb_var_screeninfo var;
 	char *last = NULL;
 	int err;
@@ -355,24 +371,27 @@
 	return count;
 }
 
-static ssize_t show_pan(struct class_device *class_device, char *buf)
+static ssize_t show_pan(struct device *device,
+			struct device_attribute *attr, char *buf)
 {
-	struct fb_info *fb_info = class_get_devdata(class_device);
+	struct fb_info *fb_info = dev_get_drvdata(device);
 	return snprintf(buf, PAGE_SIZE, "%d,%d\n", fb_info->var.xoffset,
 			fb_info->var.xoffset);
 }
 
-static ssize_t show_name(struct class_device *class_device, char *buf)
+static ssize_t show_name(struct device *device,
+			 struct device_attribute *attr, char *buf)
 {
-	struct fb_info *fb_info = class_get_devdata(class_device);
+	struct fb_info *fb_info = dev_get_drvdata(device);
 
 	return snprintf(buf, PAGE_SIZE, "%s\n", fb_info->fix.id);
 }
 
-static ssize_t store_fbstate(struct class_device *class_device,
-			const char *buf, size_t count)
+static ssize_t store_fbstate(struct device *device,
+			     struct device_attribute *attr,
+			     const char *buf, size_t count)
 {
-	struct fb_info *fb_info = class_get_devdata(class_device);
+	struct fb_info *fb_info = dev_get_drvdata(device);
 	u32 state;
 	char *last = NULL;
 
@@ -385,17 +404,19 @@
 	return count;
 }
 
-static ssize_t show_fbstate(struct class_device *class_device, char *buf)
+static ssize_t show_fbstate(struct device *device,
+			    struct device_attribute *attr, char *buf)
 {
-	struct fb_info *fb_info = class_get_devdata(class_device);
+	struct fb_info *fb_info = dev_get_drvdata(device);
 	return snprintf(buf, PAGE_SIZE, "%d\n", fb_info->state);
 }
 
 #ifdef CONFIG_FB_BACKLIGHT
-static ssize_t store_bl_curve(struct class_device *class_device,
-		const char *buf, size_t count)
+static ssize_t store_bl_curve(struct device *device,
+			      struct device_attribute *attr,
+			      const char *buf, size_t count)
 {
-	struct fb_info *fb_info = class_get_devdata(class_device);
+	struct fb_info *fb_info = dev_get_drvdata(device);
 	u8 tmp_curve[FB_BACKLIGHT_LEVELS];
 	unsigned int i;
 
@@ -432,9 +453,10 @@
 	return count;
 }
 
-static ssize_t show_bl_curve(struct class_device *class_device, char *buf)
+static ssize_t show_bl_curve(struct device *device,
+			     struct device_attribute *attr, char *buf)
 {
-	struct fb_info *fb_info = class_get_devdata(class_device);
+	struct fb_info *fb_info = dev_get_drvdata(device);
 	ssize_t len = 0;
 	unsigned int i;
 
@@ -465,7 +487,7 @@
 /* When cmap is added back in it should be a binary attribute
  * not a text one. Consideration should also be given to converting
  * fbdev to use configfs instead of sysfs */
-static struct class_device_attribute class_device_attrs[] = {
+static struct device_attribute device_attrs[] = {
 	__ATTR(bits_per_pixel, S_IRUGO|S_IWUSR, show_bpp, store_bpp),
 	__ATTR(blank, S_IRUGO|S_IWUSR, show_blank, store_blank),
 	__ATTR(console, S_IRUGO|S_IWUSR, show_console, store_console),
@@ -483,17 +505,16 @@
 #endif
 };
 
-int fb_init_class_device(struct fb_info *fb_info)
+int fb_init_device(struct fb_info *fb_info)
 {
 	int i, error = 0;
 
-	class_set_devdata(fb_info->class_device, fb_info);
+	dev_set_drvdata(fb_info->dev, fb_info);
 
 	fb_info->class_flag |= FB_SYSFS_FLAG_ATTR;
 
-	for (i = 0; i < ARRAY_SIZE(class_device_attrs); i++) {
-		error = class_device_create_file(fb_info->class_device,
-						 &class_device_attrs[i]);
+	for (i = 0; i < ARRAY_SIZE(device_attrs); i++) {
+		error = device_create_file(fb_info->dev, &device_attrs[i]);
 
 		if (error)
 			break;
@@ -501,22 +522,20 @@
 
 	if (error) {
 		while (--i >= 0)
-			class_device_remove_file(fb_info->class_device,
-						 &class_device_attrs[i]);
+			device_remove_file(fb_info->dev, &device_attrs[i]);
 		fb_info->class_flag &= ~FB_SYSFS_FLAG_ATTR;
 	}
 
 	return 0;
 }
 
-void fb_cleanup_class_device(struct fb_info *fb_info)
+void fb_cleanup_device(struct fb_info *fb_info)
 {
 	unsigned int i;
 
 	if (fb_info->class_flag & FB_SYSFS_FLAG_ATTR) {
-		for (i = 0; i < ARRAY_SIZE(class_device_attrs); i++)
-			class_device_remove_file(fb_info->class_device,
-						 &class_device_attrs[i]);
+		for (i = 0; i < ARRAY_SIZE(device_attrs); i++)
+			device_remove_file(fb_info->dev, &device_attrs[i]);
 
 		fb_info->class_flag &= ~FB_SYSFS_FLAG_ATTR;
 	}
diff --git a/fs/Kconfig b/fs/Kconfig
index 7b1511d..b3b5aa0 100644
--- a/fs/Kconfig
+++ b/fs/Kconfig
@@ -972,7 +972,7 @@
 
 	Some system agents rely on the information in sysfs to operate.
 	/sbin/hotplug uses device and object attributes in sysfs to assist in
-	delegating policy decisions, like persistantly naming devices.
+	delegating policy decisions, like persistently naming devices.
 
 	sysfs is currently used by the block subsystem to mount the root
 	partition.  If sysfs is disabled you must specify the boot device on
@@ -1145,7 +1145,7 @@
 	help
 	  The BeOS File System (BeFS) is the native file system of Be, Inc's
 	  BeOS. Notable features include support for arbitrary attributes
-	  on files and directories, and database-like indeces on selected
+	  on files and directories, and database-like indices on selected
 	  attributes. (Also note that this driver doesn't make those features
 	  available at this time). It is a 64 bit filesystem, so it supports
 	  extremely large volumes and files.
diff --git a/fs/aio.c b/fs/aio.c
index 9476659..277a5f2 100644
--- a/fs/aio.c
+++ b/fs/aio.c
@@ -367,8 +367,7 @@
 {
 	unsigned nr_events = ctx->max_reqs;
 
-	if (unlikely(ctx->reqs_active))
-		BUG();
+	BUG_ON(ctx->reqs_active);
 
 	cancel_delayed_work(&ctx->wq);
 	flush_workqueue(aio_wq);
@@ -505,8 +504,7 @@
 	assert_spin_locked(&ctx->ctx_lock);
 
 	req->ki_users --;
-	if (unlikely(req->ki_users < 0))
-		BUG();
+	BUG_ON(req->ki_users < 0);
 	if (likely(req->ki_users))
 		return 0;
 	list_del(&req->ki_list);		/* remove from active_reqs */
diff --git a/fs/bio.c b/fs/bio.c
index f95c874..aa4d09b 100644
--- a/fs/bio.c
+++ b/fs/bio.c
@@ -560,10 +560,8 @@
 			break;
 		}
 
-		if (bio_add_pc_page(q, bio, page, bytes, 0) < bytes) {
-			ret = -EINVAL;
+		if (bio_add_pc_page(q, bio, page, bytes, 0) < bytes)
 			break;
-		}
 
 		len -= bytes;
 	}
@@ -622,10 +620,9 @@
 
 		nr_pages += end - start;
 		/*
-		 * transfer and buffer must be aligned to at least hardsector
-		 * size for now, in the future we can relax this restriction
+		 * buffer must be aligned to at least hardsector size for now
 		 */
-		if ((uaddr & queue_dma_alignment(q)) || (len & queue_dma_alignment(q)))
+		if (uaddr & queue_dma_alignment(q))
 			return ERR_PTR(-EINVAL);
 	}
 
@@ -751,7 +748,6 @@
 			     int write_to_vm)
 {
 	struct bio *bio;
-	int len = 0, i;
 
 	bio = __bio_map_user_iov(q, bdev, iov, iov_count, write_to_vm);
 
@@ -766,18 +762,7 @@
 	 */
 	bio_get(bio);
 
-	for (i = 0; i < iov_count; i++)
-		len += iov[i].iov_len;
-
-	if (bio->bi_size == len)
-		return bio;
-
-	/*
-	 * don't support partial mappings
-	 */
-	bio_endio(bio, bio->bi_size, 0);
-	bio_unmap_user(bio);
-	return ERR_PTR(-EINVAL);
+	return bio;
 }
 
 static void __bio_unmap_user(struct bio *bio)
diff --git a/fs/cifs/inode.c b/fs/cifs/inode.c
index 1ad8c9f..c4fa91b 100644
--- a/fs/cifs/inode.c
+++ b/fs/cifs/inode.c
@@ -318,6 +318,7 @@
 	struct cifs_sb_info *cifs_sb = CIFS_SB(sb);
 	char *tmp_path;
 	char *buf = NULL;
+	int adjustTZ = FALSE;
 
 	pTcon = cifs_sb->tcon;
 	cFYI(1,("Getting info on %s", search_path));
@@ -348,6 +349,7 @@
 					pfindData, cifs_sb->local_nls, 
 					cifs_sb->mnt_cifs_flags &
 					  CIFS_MOUNT_MAP_SPECIAL_CHR);
+			adjustTZ = TRUE;
 		}
 		
 	}
@@ -444,6 +446,10 @@
 		inode->i_ctime =
 		    cifs_NTtimeToUnix(le64_to_cpu(pfindData->ChangeTime));
 		cFYI(0, ("Attributes came in as 0x%x", attr));
+		if(adjustTZ && (pTcon->ses) && (pTcon->ses->server)) {
+			inode->i_ctime.tv_sec += pTcon->ses->server->timeAdj;
+	                inode->i_mtime.tv_sec += pTcon->ses->server->timeAdj;
+		}
 
 		/* set default mode. will override for dirs below */
 		if (atomic_read(&cifsInfo->inUse) == 0)
diff --git a/fs/cifs/link.c b/fs/cifs/link.c
index 0bee8b7..8e25996 100644
--- a/fs/cifs/link.c
+++ b/fs/cifs/link.c
@@ -69,17 +69,30 @@
 			rc = -EOPNOTSUPP;  
 	}
 
-/* if (!rc)     */
-	{
-		/*   renew_parental_timestamps(old_file);
-		   inode->i_nlink++;
-		   mark_inode_dirty(inode);
-		   d_instantiate(direntry, inode); */
-		/* BB add call to either mark inode dirty or refresh its data and timestamp to current time */
+	d_drop(direntry);	/* force new lookup from server of target */
+
+	/* if source file is cached (oplocked) revalidate will not go to server
+	   until the file is closed or oplock broken so update nlinks locally */
+	if(old_file->d_inode) {
+		cifsInode = CIFS_I(old_file->d_inode);
+		if(rc == 0) {
+			old_file->d_inode->i_nlink++;
+			old_file->d_inode->i_ctime = CURRENT_TIME;
+			/* parent dir timestamps will update from srv
+			within a second, would it really be worth it
+			to set the parent dir cifs inode time to zero
+			to force revalidate (faster) for it too? */
+		}
+		/* if not oplocked will force revalidate to get info 
+		   on source file from srv */
+		cifsInode->time = 0;
+
+                /* Will update parent dir timestamps from srv within a second.
+		   Would it really be worth it to set the parent dir (cifs
+		   inode) time field to zero to force revalidate on parent
+		   directory faster ie 
+			CIFS_I(inode)->time = 0;  */
 	}
-	d_drop(direntry);	/* force new lookup from server */
-	cifsInode = CIFS_I(old_file->d_inode);
-	cifsInode->time = 0;	/* will force revalidate to go get info when needed */
 
 cifs_hl_exit:
 	kfree(fromName);
diff --git a/fs/jfs/jfs_filsys.h b/fs/jfs/jfs_filsys.h
index 9901928..eb550b3 100644
--- a/fs/jfs/jfs_filsys.h
+++ b/fs/jfs/jfs_filsys.h
@@ -81,7 +81,7 @@
 #define	JFS_SWAP_BYTES		0x00100000	/* running on big endian computer */
 
 /* Directory index */
-#define JFS_DIR_INDEX		0x00200000	/* Persistant index for */
+#define JFS_DIR_INDEX		0x00200000	/* Persistent index for */
 						/* directory entries    */
 
 
diff --git a/fs/reiserfs/journal.c b/fs/reiserfs/journal.c
index 85ce232..ac93174 100644
--- a/fs/reiserfs/journal.c
+++ b/fs/reiserfs/journal.c
@@ -1464,7 +1464,7 @@
 		}
 
 		/* if someone has this block in a newer transaction, just make
-		 ** sure they are commited, and don't try writing it to disk
+		 ** sure they are committed, and don't try writing it to disk
 		 */
 		if (pjl) {
 			if (atomic_read(&pjl->j_commit_left))
@@ -3384,7 +3384,7 @@
 
 /*
 ** for any cnode in a journal list, it can only be dirtied of all the
-** transactions that include it are commited to disk.
+** transactions that include it are committed to disk.
 ** this checks through each transaction, and returns 1 if you are allowed to dirty,
 ** and 0 if you aren't
 **
@@ -3426,7 +3426,7 @@
 }
 
 /* syncs the commit blocks, but does not force the real buffers to disk
-** will wait until the current transaction is done/commited before returning 
+** will wait until the current transaction is done/committed before returning 
 */
 int journal_end_sync(struct reiserfs_transaction_handle *th,
 		     struct super_block *p_s_sb, unsigned long nblocks)
diff --git a/fs/sysfs/dir.c b/fs/sysfs/dir.c
index 3aa3434..a5782e8 100644
--- a/fs/sysfs/dir.c
+++ b/fs/sysfs/dir.c
@@ -372,6 +372,51 @@
 	return error;
 }
 
+int sysfs_move_dir(struct kobject *kobj, struct kobject *new_parent)
+{
+	struct dentry *old_parent_dentry, *new_parent_dentry, *new_dentry;
+	struct sysfs_dirent *new_parent_sd, *sd;
+	int error;
+
+	if (!new_parent)
+		return -EINVAL;
+
+	old_parent_dentry = kobj->parent ?
+		kobj->parent->dentry : sysfs_mount->mnt_sb->s_root;
+	new_parent_dentry = new_parent->dentry;
+
+again:
+	mutex_lock(&old_parent_dentry->d_inode->i_mutex);
+	if (!mutex_trylock(&new_parent_dentry->d_inode->i_mutex)) {
+		mutex_unlock(&old_parent_dentry->d_inode->i_mutex);
+		goto again;
+	}
+
+	new_parent_sd = new_parent_dentry->d_fsdata;
+	sd = kobj->dentry->d_fsdata;
+
+	new_dentry = lookup_one_len(kobj->name, new_parent_dentry,
+				    strlen(kobj->name));
+	if (IS_ERR(new_dentry)) {
+		error = PTR_ERR(new_dentry);
+		goto out;
+	} else
+		error = 0;
+	d_add(new_dentry, NULL);
+	d_move(kobj->dentry, new_dentry);
+	dput(new_dentry);
+
+	/* Remove from old parent's list and insert into new parent's list. */
+	list_del_init(&sd->s_sibling);
+	list_add(&sd->s_sibling, &new_parent_sd->s_children);
+
+out:
+	mutex_unlock(&new_parent_dentry->d_inode->i_mutex);
+	mutex_unlock(&old_parent_dentry->d_inode->i_mutex);
+
+	return error;
+}
+
 static int sysfs_dir_open(struct inode *inode, struct file *file)
 {
 	struct dentry * dentry = file->f_dentry;
diff --git a/fs/sysfs/file.c b/fs/sysfs/file.c
index 298303b..95c1651 100644
--- a/fs/sysfs/file.c
+++ b/fs/sysfs/file.c
@@ -190,6 +190,9 @@
 		count = PAGE_SIZE - 1;
 	error = copy_from_user(buffer->page,buf,count);
 	buffer->needs_read_fill = 1;
+	/* if buf is assumed to contain a string, terminate it by \0,
+	   so e.g. sscanf() can scan the string easily */
+	buffer->page[count] = 0;
 	return error ? -EFAULT : count;
 }
 
diff --git a/include/acpi/acpi_bus.h b/include/acpi/acpi_bus.h
index f338e40..fdd1095 100644
--- a/include/acpi/acpi_bus.h
+++ b/include/acpi/acpi_bus.h
@@ -357,7 +357,7 @@
 /* helper */
 acpi_handle acpi_get_child(acpi_handle, acpi_integer);
 acpi_handle acpi_get_pci_rootbridge_handle(unsigned int, unsigned int);
-#define DEVICE_ACPI_HANDLE(dev) ((acpi_handle)((dev)->firmware_data))
+#define DEVICE_ACPI_HANDLE(dev) ((acpi_handle)((dev)->archdata.acpi_handle))
 
 #endif /* CONFIG_ACPI */
 
diff --git a/include/asm-alpha/device.h b/include/asm-alpha/device.h
new file mode 100644
index 0000000..d8f9872
--- /dev/null
+++ b/include/asm-alpha/device.h
@@ -0,0 +1,7 @@
+/*
+ * Arch specific extensions to struct device
+ *
+ * This file is released under the GPLv2
+ */
+#include <asm-generic/device.h>
+
diff --git a/include/asm-arm/device.h b/include/asm-arm/device.h
new file mode 100644
index 0000000..d8f9872
--- /dev/null
+++ b/include/asm-arm/device.h
@@ -0,0 +1,7 @@
+/*
+ * Arch specific extensions to struct device
+ *
+ * This file is released under the GPLv2
+ */
+#include <asm-generic/device.h>
+
diff --git a/include/asm-arm26/device.h b/include/asm-arm26/device.h
new file mode 100644
index 0000000..d8f9872
--- /dev/null
+++ b/include/asm-arm26/device.h
@@ -0,0 +1,7 @@
+/*
+ * Arch specific extensions to struct device
+ *
+ * This file is released under the GPLv2
+ */
+#include <asm-generic/device.h>
+
diff --git a/include/asm-avr32/device.h b/include/asm-avr32/device.h
new file mode 100644
index 0000000..d8f9872
--- /dev/null
+++ b/include/asm-avr32/device.h
@@ -0,0 +1,7 @@
+/*
+ * Arch specific extensions to struct device
+ *
+ * This file is released under the GPLv2
+ */
+#include <asm-generic/device.h>
+
diff --git a/include/asm-cris/device.h b/include/asm-cris/device.h
new file mode 100644
index 0000000..d8f9872
--- /dev/null
+++ b/include/asm-cris/device.h
@@ -0,0 +1,7 @@
+/*
+ * Arch specific extensions to struct device
+ *
+ * This file is released under the GPLv2
+ */
+#include <asm-generic/device.h>
+
diff --git a/include/asm-frv/device.h b/include/asm-frv/device.h
new file mode 100644
index 0000000..d8f9872
--- /dev/null
+++ b/include/asm-frv/device.h
@@ -0,0 +1,7 @@
+/*
+ * Arch specific extensions to struct device
+ *
+ * This file is released under the GPLv2
+ */
+#include <asm-generic/device.h>
+
diff --git a/include/asm-generic/device.h b/include/asm-generic/device.h
new file mode 100644
index 0000000..c17c960
--- /dev/null
+++ b/include/asm-generic/device.h
@@ -0,0 +1,12 @@
+/*
+ * Arch specific extensions to struct device
+ *
+ * This file is released under the GPLv2
+ */
+#ifndef _ASM_GENERIC_DEVICE_H
+#define _ASM_GENERIC_DEVICE_H
+
+struct dev_archdata {
+};
+
+#endif /* _ASM_GENERIC_DEVICE_H */
diff --git a/include/asm-h8300/device.h b/include/asm-h8300/device.h
new file mode 100644
index 0000000..d8f9872
--- /dev/null
+++ b/include/asm-h8300/device.h
@@ -0,0 +1,7 @@
+/*
+ * Arch specific extensions to struct device
+ *
+ * This file is released under the GPLv2
+ */
+#include <asm-generic/device.h>
+
diff --git a/include/asm-i386/device.h b/include/asm-i386/device.h
new file mode 100644
index 0000000..849604c
--- /dev/null
+++ b/include/asm-i386/device.h
@@ -0,0 +1,15 @@
+/*
+ * Arch specific extensions to struct device
+ *
+ * This file is released under the GPLv2
+ */
+#ifndef _ASM_I386_DEVICE_H
+#define _ASM_I386_DEVICE_H
+
+struct dev_archdata {
+#ifdef CONFIG_ACPI
+	void	*acpi_handle;
+#endif
+};
+
+#endif /* _ASM_I386_DEVICE_H */
diff --git a/include/asm-ia64/device.h b/include/asm-ia64/device.h
new file mode 100644
index 0000000..3db6daf
--- /dev/null
+++ b/include/asm-ia64/device.h
@@ -0,0 +1,15 @@
+/*
+ * Arch specific extensions to struct device
+ *
+ * This file is released under the GPLv2
+ */
+#ifndef _ASM_IA64_DEVICE_H
+#define _ASM_IA64_DEVICE_H
+
+struct dev_archdata {
+#ifdef CONFIG_ACPI
+	void	*acpi_handle;
+#endif
+};
+
+#endif /* _ASM_IA64_DEVICE_H */
diff --git a/include/asm-ia64/io.h b/include/asm-ia64/io.h
index 855c30a..6311e16 100644
--- a/include/asm-ia64/io.h
+++ b/include/asm-ia64/io.h
@@ -32,7 +32,7 @@
  */
 #define IO_SPACE_LIMIT		0xffffffffffffffffUL
 
-#define MAX_IO_SPACES_BITS		4
+#define MAX_IO_SPACES_BITS		8
 #define MAX_IO_SPACES			(1UL << MAX_IO_SPACES_BITS)
 #define IO_SPACE_BITS			24
 #define IO_SPACE_SIZE			(1UL << IO_SPACE_BITS)
diff --git a/include/asm-ia64/machvec.h b/include/asm-ia64/machvec.h
index 7ffbddf..8f784f8 100644
--- a/include/asm-ia64/machvec.h
+++ b/include/asm-ia64/machvec.h
@@ -36,6 +36,7 @@
 typedef int ia64_mv_pci_legacy_write_t (struct pci_bus *, u16 port, u32 val,
 					u8 size);
 typedef void ia64_mv_migrate_t(struct task_struct * task);
+typedef void ia64_mv_pci_fixup_bus_t (struct pci_bus *);
 
 /* DMA-mapping interface: */
 typedef void ia64_mv_dma_init (void);
@@ -95,6 +96,11 @@
 {
 }
 
+static inline void
+machvec_noop_bus (struct pci_bus *bus)
+{
+}
+
 extern void machvec_setup (char **);
 extern void machvec_timer_interrupt (int, void *);
 extern void machvec_dma_sync_single (struct device *, dma_addr_t, size_t, int);
@@ -159,6 +165,7 @@
 #  define platform_migrate		ia64_mv.migrate
 #  define platform_setup_msi_irq	ia64_mv.setup_msi_irq
 #  define platform_teardown_msi_irq	ia64_mv.teardown_msi_irq
+#  define platform_pci_fixup_bus	ia64_mv.pci_fixup_bus
 # endif
 
 /* __attribute__((__aligned__(16))) is required to make size of the
@@ -210,6 +217,7 @@
 	ia64_mv_migrate_t *migrate;
 	ia64_mv_setup_msi_irq_t *setup_msi_irq;
 	ia64_mv_teardown_msi_irq_t *teardown_msi_irq;
+	ia64_mv_pci_fixup_bus_t *pci_fixup_bus;
 } __attribute__((__aligned__(16))); /* align attrib? see above comment */
 
 #define MACHVEC_INIT(name)			\
@@ -257,6 +265,7 @@
 	platform_migrate,			\
 	platform_setup_msi_irq,			\
 	platform_teardown_msi_irq,		\
+	platform_pci_fixup_bus,			\
 }
 
 extern struct ia64_machine_vector ia64_mv;
@@ -416,5 +425,8 @@
 #ifndef platform_teardown_msi_irq
 # define platform_teardown_msi_irq	((ia64_mv_teardown_msi_irq_t*)NULL)
 #endif
+#ifndef platform_pci_fixup_bus
+# define platform_pci_fixup_bus	machvec_noop_bus
+#endif
 
 #endif /* _ASM_IA64_MACHVEC_H */
diff --git a/include/asm-ia64/machvec_sn2.h b/include/asm-ia64/machvec_sn2.h
index c54b165..83325f6 100644
--- a/include/asm-ia64/machvec_sn2.h
+++ b/include/asm-ia64/machvec_sn2.h
@@ -69,6 +69,7 @@
 extern ia64_mv_migrate_t		sn_migrate;
 extern ia64_mv_setup_msi_irq_t		sn_setup_msi_irq;
 extern ia64_mv_teardown_msi_irq_t	sn_teardown_msi_irq;
+extern ia64_mv_pci_fixup_bus_t		sn_pci_fixup_bus;
 
 
 /*
@@ -127,6 +128,7 @@
 #define platform_setup_msi_irq		((ia64_mv_setup_msi_irq_t*)NULL)
 #define platform_teardown_msi_irq	((ia64_mv_teardown_msi_irq_t*)NULL)
 #endif
+#define platform_pci_fixup_bus		sn_pci_fixup_bus
 
 #include <asm/sn/io.h>
 
diff --git a/include/asm-ia64/pci.h b/include/asm-ia64/pci.h
index ef616fd..825eb7d 100644
--- a/include/asm-ia64/pci.h
+++ b/include/asm-ia64/pci.h
@@ -26,16 +26,18 @@
 struct pci_dev;
 
 /*
- * PCI_DMA_BUS_IS_PHYS should be set to 1 if there is _necessarily_ a direct correspondence
- * between device bus addresses and CPU physical addresses.  Platforms with a hardware I/O
- * MMU _must_ turn this off to suppress the bounce buffer handling code in the block and
- * network device layers.  Platforms with separate bus address spaces _must_ turn this off
- * and provide a device DMA mapping implementation that takes care of the necessary
+ * PCI_DMA_BUS_IS_PHYS should be set to 1 if there is _necessarily_ a direct
+ * correspondence between device bus addresses and CPU physical addresses.
+ * Platforms with a hardware I/O MMU _must_ turn this off to suppress the
+ * bounce buffer handling code in the block and network device layers.
+ * Platforms with separate bus address spaces _must_ turn this off and provide
+ * a device DMA mapping implementation that takes care of the necessary
  * address translation.
  *
- * For now, the ia64 platforms which may have separate/multiple bus address spaces all
- * have I/O MMUs which support the merging of physically discontiguous buffers, so we can
- * use that as the sole factor to determine the setting of PCI_DMA_BUS_IS_PHYS.
+ * For now, the ia64 platforms which may have separate/multiple bus address
+ * spaces all have I/O MMUs which support the merging of physically
+ * discontiguous buffers, so we can use that as the sole factor to determine
+ * the setting of PCI_DMA_BUS_IS_PHYS.
  */
 extern unsigned long ia64_max_iommu_merge_mask;
 #define PCI_DMA_BUS_IS_PHYS	(ia64_max_iommu_merge_mask == ~0UL)
@@ -52,9 +54,6 @@
 	/* We don't do dynamic PCI IRQ allocation */
 }
 
-#define HAVE_ARCH_PCI_MWI 1
-extern int pcibios_prep_mwi (struct pci_dev *);
-
 #include <asm-generic/pci-dma-compat.h>
 
 /* pci_unmap_{single,page} is not a nop, thus... */
diff --git a/include/asm-ia64/sn/acpi.h b/include/asm-ia64/sn/acpi.h
new file mode 100644
index 0000000..2850a7e
--- /dev/null
+++ b/include/asm-ia64/sn/acpi.h
@@ -0,0 +1,16 @@
+/*
+ * This file is subject to the terms and conditions of the GNU General Public
+ * License.  See the file "COPYING" in the main directory of this archive
+ * for more details.
+ *
+ * Copyright (C) 2006 Silicon Graphics, Inc. All rights reserved.
+ */
+
+#ifndef _ASM_IA64_SN_ACPI_H
+#define _ASM_IA64_SN_ACPI_H
+
+#include "acpi/acglobal.h"
+
+#define SN_ACPI_BASE_SUPPORT()   (acpi_gbl_DSDT->oem_revision >= 0x20101)
+
+#endif /* _ASM_IA64_SN_ACPI_H */
diff --git a/include/asm-ia64/sn/pcidev.h b/include/asm-ia64/sn/pcidev.h
index eac3561..9fe89a9 100644
--- a/include/asm-ia64/sn/pcidev.h
+++ b/include/asm-ia64/sn/pcidev.h
@@ -3,7 +3,7 @@
  * License.  See the file "COPYING" in the main directory of this archive
  * for more details.
  *
- * Copyright (C) 1992 - 1997, 2000-2005 Silicon Graphics, Inc. All rights reserved.
+ * Copyright (C) 1992 - 1997, 2000-2006 Silicon Graphics, Inc. All rights reserved.
  */
 #ifndef _ASM_IA64_SN_PCI_PCIDEV_H
 #define _ASM_IA64_SN_PCI_PCIDEV_H
@@ -12,31 +12,29 @@
 
 /*
  * In ia64, pci_dev->sysdata must be a *pci_controller. To provide access to
- * the pcidev_info structs for all devices under a controller, we extend the
- * definition of pci_controller, via sn_pci_controller, to include a list
- * of pcidev_info.
+ * the pcidev_info structs for all devices under a controller, we keep a
+ * list of pcidev_info under pci_controller->platform_data.
  */
-struct sn_pci_controller {
-	struct pci_controller pci_controller;
+struct sn_platform_data {
+	void *provider_soft;
 	struct list_head pcidev_info;
 };
 
-#define SN_PCI_CONTROLLER(dev) ((struct sn_pci_controller *) dev->sysdata)
+#define SN_PLATFORM_DATA(busdev) \
+	((struct sn_platform_data *)(PCI_CONTROLLER(busdev)->platform_data))
 
 #define SN_PCIDEV_INFO(dev)	sn_pcidev_info_get(dev)
 
-#define SN_PCIBUS_BUSSOFT_INFO(pci_bus) \
-	(struct pcibus_info *)((struct pcibus_bussoft *)(PCI_CONTROLLER((pci_bus))->platform_data))
 /*
  * Given a pci_bus, return the sn pcibus_bussoft struct.  Note that
  * this only works for root busses, not for busses represented by PPB's.
  */
 
 #define SN_PCIBUS_BUSSOFT(pci_bus) \
-        ((struct pcibus_bussoft *)(PCI_CONTROLLER((pci_bus))->platform_data))
+	((struct pcibus_bussoft *)(SN_PLATFORM_DATA(pci_bus)->provider_soft))
 
 #define SN_PCIBUS_BUSSOFT_INFO(pci_bus) \
-	(struct pcibus_info *)((struct pcibus_bussoft *)(PCI_CONTROLLER((pci_bus))->platform_data))
+	((struct pcibus_info *)(SN_PLATFORM_DATA(pci_bus)->provider_soft))
 /*
  * Given a struct pci_dev, return the sn pcibus_bussoft struct.  Note
  * that this is not equivalent to SN_PCIBUS_BUSSOFT(pci_dev->bus) due
@@ -72,8 +70,6 @@
 			 struct sn_irq_info *sn_irq_info);
 extern void sn_irq_unfixup(struct pci_dev *pci_dev);
 extern struct pcidev_info * sn_pcidev_info_get(struct pci_dev *);
-extern void sn_pci_controller_fixup(int segment, int busnum,
- 				    struct pci_bus *bus);
 extern void sn_bus_store_sysdata(struct pci_dev *dev);
 extern void sn_bus_free_sysdata(void);
 extern void sn_generate_path(struct pci_bus *pci_bus, char *address);
diff --git a/include/asm-ia64/sn/sn_feature_sets.h b/include/asm-ia64/sn/sn_feature_sets.h
index 30dcfa4..bfdc362 100644
--- a/include/asm-ia64/sn/sn_feature_sets.h
+++ b/include/asm-ia64/sn/sn_feature_sets.h
@@ -44,8 +44,14 @@
  * Once enabled, a feature cannot be disabled.
  *
  * By default, features are disabled unless explicitly enabled.
+ *
+ * These defines must be kept in sync with the corresponding
+ * PROM definitions in feature_sets.h.
  */
 #define  OSF_MCA_SLV_TO_OS_INIT_SLV	0
 #define  OSF_FEAT_LOG_SBES		1
+#define  OSF_ACPI_ENABLE		2
+#define  OSF_PCISEGMENT_ENABLE		3
+
 
 #endif /* _ASM_IA64_SN_FEATURE_SETS_H */
diff --git a/include/asm-ia64/sn/sn_sal.h b/include/asm-ia64/sn/sn_sal.h
index ba826b3..be5d83a 100644
--- a/include/asm-ia64/sn/sn_sal.h
+++ b/include/asm-ia64/sn/sn_sal.h
@@ -77,6 +77,7 @@
 #define  SN_SAL_IOIF_GET_WIDGET_DMAFLUSH_LIST	   0x02000058	// deprecated
 #define  SN_SAL_IOIF_GET_DEVICE_DMAFLUSH_LIST	   0x0200005a
 
+#define SN_SAL_IOIF_INIT			   0x0200005f
 #define SN_SAL_HUB_ERROR_INTERRUPT		   0x02000060
 #define SN_SAL_BTE_RECOVER			   0x02000061
 #define SN_SAL_RESERVED_DO_NOT_USE		   0x02000062
diff --git a/include/asm-m32r/device.h b/include/asm-m32r/device.h
new file mode 100644
index 0000000..d8f9872
--- /dev/null
+++ b/include/asm-m32r/device.h
@@ -0,0 +1,7 @@
+/*
+ * Arch specific extensions to struct device
+ *
+ * This file is released under the GPLv2
+ */
+#include <asm-generic/device.h>
+
diff --git a/include/asm-m68k/device.h b/include/asm-m68k/device.h
new file mode 100644
index 0000000..d8f9872
--- /dev/null
+++ b/include/asm-m68k/device.h
@@ -0,0 +1,7 @@
+/*
+ * Arch specific extensions to struct device
+ *
+ * This file is released under the GPLv2
+ */
+#include <asm-generic/device.h>
+
diff --git a/include/asm-m68knommu/device.h b/include/asm-m68knommu/device.h
new file mode 100644
index 0000000..d8f9872
--- /dev/null
+++ b/include/asm-m68knommu/device.h
@@ -0,0 +1,7 @@
+/*
+ * Arch specific extensions to struct device
+ *
+ * This file is released under the GPLv2
+ */
+#include <asm-generic/device.h>
+
diff --git a/include/asm-m68knommu/mcfmbus.h b/include/asm-m68knommu/mcfmbus.h
index 13df9d4..319899c 100644
--- a/include/asm-m68knommu/mcfmbus.h
+++ b/include/asm-m68knommu/mcfmbus.h
@@ -37,7 +37,7 @@
 #define MCFMBUS_MFDR_MBC(a)	((a)&0x3F)	   /*M-Bus Clock*/
 
 /*
-*	Define bit flags in Controll Register
+*	Define bit flags in Control Register
 */
 
 #define MCFMBUS_MBCR_MEN           (0x80)  /* M-Bus Enable                 */
diff --git a/include/asm-mips/addrspace.h b/include/asm-mips/addrspace.h
index 45c706e..c627508 100644
--- a/include/asm-mips/addrspace.h
+++ b/include/asm-mips/addrspace.h
@@ -19,12 +19,16 @@
 #define _ATYPE_
 #define _ATYPE32_
 #define _ATYPE64_
-#define _LLCONST_(x)	x
+#define _CONST64_(x)	x
 #else
 #define _ATYPE_		__PTRDIFF_TYPE__
 #define _ATYPE32_	int
-#define _ATYPE64_	long long
-#define _LLCONST_(x)	x ## LL
+#define _ATYPE64_	__s64
+#ifdef CONFIG_64BIT
+#define _CONST64_(x)	x ## L
+#else
+#define _CONST64_(x)	x ## LL
+#endif
 #endif
 
 /*
@@ -48,7 +52,7 @@
  */
 #define CPHYSADDR(a)		((_ACAST32_(a)) & 0x1fffffff)
 #define XPHYSADDR(a)            ((_ACAST64_(a)) &			\
-				 _LLCONST_(0x000000ffffffffff))
+				 _CONST64_(0x000000ffffffffff))
 
 #ifdef CONFIG_64BIT
 
@@ -57,14 +61,14 @@
  * The compatibility segments use the full 64-bit sign extended value.  Note
  * the R8000 doesn't have them so don't reference these in generic MIPS code.
  */
-#define XKUSEG			_LLCONST_(0x0000000000000000)
-#define XKSSEG			_LLCONST_(0x4000000000000000)
-#define XKPHYS			_LLCONST_(0x8000000000000000)
-#define XKSEG			_LLCONST_(0xc000000000000000)
-#define CKSEG0			_LLCONST_(0xffffffff80000000)
-#define CKSEG1			_LLCONST_(0xffffffffa0000000)
-#define CKSSEG			_LLCONST_(0xffffffffc0000000)
-#define CKSEG3			_LLCONST_(0xffffffffe0000000)
+#define XKUSEG			_CONST64_(0x0000000000000000)
+#define XKSSEG			_CONST64_(0x4000000000000000)
+#define XKPHYS			_CONST64_(0x8000000000000000)
+#define XKSEG			_CONST64_(0xc000000000000000)
+#define CKSEG0			_CONST64_(0xffffffff80000000)
+#define CKSEG1			_CONST64_(0xffffffffa0000000)
+#define CKSSEG			_CONST64_(0xffffffffc0000000)
+#define CKSEG3			_CONST64_(0xffffffffe0000000)
 
 #define CKSEG0ADDR(a)		(CPHYSADDR(a) | CKSEG0)
 #define CKSEG1ADDR(a)		(CPHYSADDR(a) | CKSEG1)
@@ -122,7 +126,7 @@
 #define PHYS_TO_XKSEG_UNCACHED(p)	PHYS_TO_XKPHYS(K_CALG_UNCACHED,(p))
 #define PHYS_TO_XKSEG_CACHED(p)		PHYS_TO_XKPHYS(K_CALG_COH_SHAREABLE,(p))
 #define XKPHYS_TO_PHYS(p)		((p) & TO_PHYS_MASK)
-#define PHYS_TO_XKPHYS(cm,a)		(_LLCONST_(0x8000000000000000) | \
+#define PHYS_TO_XKPHYS(cm,a)		(_CONST64_(0x8000000000000000) | \
 					 ((cm)<<59) | (a))
 
 #if defined (CONFIG_CPU_R4300)						\
@@ -132,20 +136,20 @@
     || defined (CONFIG_CPU_NEVADA)					\
     || defined (CONFIG_CPU_TX49XX)					\
     || defined (CONFIG_CPU_MIPS64)
-#define TO_PHYS_MASK	_LLCONST_(0x0000000fffffffff)	/* 2^^36 - 1 */
+#define TO_PHYS_MASK	_CONST64_(0x0000000fffffffff)	/* 2^^36 - 1 */
 #endif
 
 #if defined (CONFIG_CPU_R8000)
 /* We keep KUSIZE consistent with R4000 for now (2^^40) instead of (2^^48) */
-#define TO_PHYS_MASK	_LLCONST_(0x000000ffffffffff)	/* 2^^40 - 1 */
+#define TO_PHYS_MASK	_CONST64_(0x000000ffffffffff)	/* 2^^40 - 1 */
 #endif
 
 #if defined (CONFIG_CPU_R10000)
-#define TO_PHYS_MASK	_LLCONST_(0x000000ffffffffff)	/* 2^^40 - 1 */
+#define TO_PHYS_MASK	_CONST64_(0x000000ffffffffff)	/* 2^^40 - 1 */
 #endif
 
 #if defined(CONFIG_CPU_SB1) || defined(CONFIG_CPU_SB1A)
-#define TO_PHYS_MASK	_LLCONST_(0x00000fffffffffff)	/* 2^^44 - 1 */
+#define TO_PHYS_MASK	_CONST64_(0x00000fffffffffff)	/* 2^^44 - 1 */
 #endif
 
 #ifndef CONFIG_CPU_R8000
@@ -155,7 +159,7 @@
  * in order to catch bugs in the source code.
  */
 
-#define COMPAT_K1BASE32		_LLCONST_(0xffffffffa0000000)
+#define COMPAT_K1BASE32		_CONST64_(0xffffffffa0000000)
 #define PHYS_TO_COMPATK1(x)	((x) | COMPAT_K1BASE32) /* 32-bit compat k1 */
 
 #endif
diff --git a/include/asm-mips/atomic.h b/include/asm-mips/atomic.h
index e64abc0..7978d8e 100644
--- a/include/asm-mips/atomic.h
+++ b/include/asm-mips/atomic.h
@@ -9,16 +9,8 @@
  * License.  See the file "COPYING" in the main directory of this archive
  * for more details.
  *
- * Copyright (C) 1996, 97, 99, 2000, 03, 04 by Ralf Baechle
+ * Copyright (C) 1996, 97, 99, 2000, 03, 04, 06 by Ralf Baechle
  */
-
-/*
- * As workaround for the ATOMIC_DEC_AND_LOCK / atomic_dec_and_lock mess in
- * <linux/spinlock.h> we have to include <linux/spinlock.h> outside the
- * main big wrapper ...
- */
-#include <linux/spinlock.h>
-
 #ifndef _ASM_ATOMIC_H
 #define _ASM_ATOMIC_H
 
diff --git a/include/asm-mips/bitops.h b/include/asm-mips/bitops.h
index 1bb89c5..b900741 100644
--- a/include/asm-mips/bitops.h
+++ b/include/asm-mips/bitops.h
@@ -10,31 +10,26 @@
 #define _ASM_BITOPS_H
 
 #include <linux/compiler.h>
+#include <linux/irqflags.h>
 #include <linux/types.h>
 #include <asm/bug.h>
 #include <asm/byteorder.h>		/* sigh ... */
 #include <asm/cpu-features.h>
+#include <asm/sgidefs.h>
+#include <asm/war.h>
 
 #if (_MIPS_SZLONG == 32)
 #define SZLONG_LOG 5
 #define SZLONG_MASK 31UL
 #define __LL		"ll	"
 #define __SC		"sc	"
-#define cpu_to_lelongp(x) cpu_to_le32p((__u32 *) (x))
 #elif (_MIPS_SZLONG == 64)
 #define SZLONG_LOG 6
 #define SZLONG_MASK 63UL
 #define __LL		"lld	"
 #define __SC		"scd	"
-#define cpu_to_lelongp(x) cpu_to_le64p((__u64 *) (x))
 #endif
 
-#ifdef __KERNEL__
-
-#include <linux/irqflags.h>
-#include <asm/sgidefs.h>
-#include <asm/war.h>
-
 /*
  * clear_bit() doesn't provide any barrier for the compiler.
  */
@@ -42,20 +37,6 @@
 #define smp_mb__after_clear_bit()	smp_mb()
 
 /*
- * Only disable interrupt for kernel mode stuff to keep usermode stuff
- * that dares to use kernel include files alive.
- */
-
-#define __bi_flags			unsigned long flags
-#define __bi_local_irq_save(x)		local_irq_save(x)
-#define __bi_local_irq_restore(x)	local_irq_restore(x)
-#else
-#define __bi_flags
-#define __bi_local_irq_save(x)
-#define __bi_local_irq_restore(x)
-#endif /* __KERNEL__ */
-
-/*
  * set_bit - Atomically set a bit in memory
  * @nr: the bit to set
  * @addr: the address to start counting from
@@ -93,13 +74,13 @@
 	} else {
 		volatile unsigned long *a = addr;
 		unsigned long mask;
-		__bi_flags;
+		unsigned long flags;
 
 		a += nr >> SZLONG_LOG;
 		mask = 1UL << (nr & SZLONG_MASK);
-		__bi_local_irq_save(flags);
+		local_irq_save(flags);
 		*a |= mask;
-		__bi_local_irq_restore(flags);
+		local_irq_restore(flags);
 	}
 }
 
@@ -141,13 +122,13 @@
 	} else {
 		volatile unsigned long *a = addr;
 		unsigned long mask;
-		__bi_flags;
+		unsigned long flags;
 
 		a += nr >> SZLONG_LOG;
 		mask = 1UL << (nr & SZLONG_MASK);
-		__bi_local_irq_save(flags);
+		local_irq_save(flags);
 		*a &= ~mask;
-		__bi_local_irq_restore(flags);
+		local_irq_restore(flags);
 	}
 }
 
@@ -191,13 +172,13 @@
 	} else {
 		volatile unsigned long *a = addr;
 		unsigned long mask;
-		__bi_flags;
+		unsigned long flags;
 
 		a += nr >> SZLONG_LOG;
 		mask = 1UL << (nr & SZLONG_MASK);
-		__bi_local_irq_save(flags);
+		local_irq_save(flags);
 		*a ^= mask;
-		__bi_local_irq_restore(flags);
+		local_irq_restore(flags);
 	}
 }
 
@@ -258,14 +239,14 @@
 		volatile unsigned long *a = addr;
 		unsigned long mask;
 		int retval;
-		__bi_flags;
+		unsigned long flags;
 
 		a += nr >> SZLONG_LOG;
 		mask = 1UL << (nr & SZLONG_MASK);
-		__bi_local_irq_save(flags);
+		local_irq_save(flags);
 		retval = (mask & *a) != 0;
 		*a |= mask;
-		__bi_local_irq_restore(flags);
+		local_irq_restore(flags);
 
 		return retval;
 	}
@@ -330,14 +311,14 @@
 		volatile unsigned long *a = addr;
 		unsigned long mask;
 		int retval;
-		__bi_flags;
+		unsigned long flags;
 
 		a += nr >> SZLONG_LOG;
 		mask = 1UL << (nr & SZLONG_MASK);
-		__bi_local_irq_save(flags);
+		local_irq_save(flags);
 		retval = (mask & *a) != 0;
 		*a &= ~mask;
-		__bi_local_irq_restore(flags);
+		local_irq_restore(flags);
 
 		return retval;
 	}
@@ -399,23 +380,19 @@
 	} else {
 		volatile unsigned long *a = addr;
 		unsigned long mask, retval;
-		__bi_flags;
+		unsigned long flags;
 
 		a += nr >> SZLONG_LOG;
 		mask = 1UL << (nr & SZLONG_MASK);
-		__bi_local_irq_save(flags);
+		local_irq_save(flags);
 		retval = (mask & *a) != 0;
 		*a ^= mask;
-		__bi_local_irq_restore(flags);
+		local_irq_restore(flags);
 
 		return retval;
 	}
 }
 
-#undef __bi_flags
-#undef __bi_local_irq_save
-#undef __bi_local_irq_restore
-
 #include <asm-generic/bitops/non-atomic.h>
 
 /*
diff --git a/include/asm-mips/bug.h b/include/asm-mips/bug.h
index 7b4739d..4d560a5 100644
--- a/include/asm-mips/bug.h
+++ b/include/asm-mips/bug.h
@@ -1,6 +1,7 @@
 #ifndef __ASM_BUG_H
 #define __ASM_BUG_H
 
+#include <asm/sgidefs.h>
 
 #ifdef CONFIG_BUG
 
@@ -13,6 +14,17 @@
 
 #define HAVE_ARCH_BUG
 
+#if (_MIPS_ISA > _MIPS_ISA_MIPS1)
+
+#define BUG_ON(condition)						\
+do {									\
+	__asm__ __volatile__("tne $0, %0" : : "r" (condition));		\
+} while (0)
+
+#define HAVE_ARCH_BUG_ON
+
+#endif /* _MIPS_ISA > _MIPS_ISA_MIPS1 */
+
 #endif
 
 #include <asm-generic/bug.h>
diff --git a/include/asm-mips/cpu-info.h b/include/asm-mips/cpu-info.h
index a2f0c8e..610d0cd 100644
--- a/include/asm-mips/cpu-info.h
+++ b/include/asm-mips/cpu-info.h
@@ -22,12 +22,12 @@
  * Descriptor for a cache
  */
 struct cache_desc {
-	unsigned short linesz;	/* Size of line in bytes */
-	unsigned short ways;	/* Number of ways */
-	unsigned short sets;	/* Number of lines per set */
 	unsigned int waysize;	/* Bytes per way */
-	unsigned int waybit;	/* Bits to select in a cache set */
-	unsigned int flags;	/* Flags describing cache properties */
+	unsigned short sets;	/* Number of lines per set */
+	unsigned char ways;	/* Number of ways */
+	unsigned char linesz;	/* Size of line in bytes */
+	unsigned char waybit;	/* Bits to select in a cache set */
+	unsigned char flags;	/* Flags describing cache properties */
 };
 
 /*
diff --git a/include/asm-mips/dec/kn02.h b/include/asm-mips/dec/kn02.h
index 8319ad7..93430b5 100644
--- a/include/asm-mips/dec/kn02.h
+++ b/include/asm-mips/dec/kn02.h
@@ -82,11 +82,9 @@
 
 #ifndef __ASSEMBLY__
 
-#include <linux/spinlock.h>
 #include <linux/types.h>
 
 extern u32 cached_kn02_csr;
-extern spinlock_t kn02_lock;
 extern void init_kn02_irqs(int base);
 #endif
 
diff --git a/include/asm-mips/device.h b/include/asm-mips/device.h
new file mode 100644
index 0000000..d8f9872
--- /dev/null
+++ b/include/asm-mips/device.h
@@ -0,0 +1,7 @@
+/*
+ * Arch specific extensions to struct device
+ *
+ * This file is released under the GPLv2
+ */
+#include <asm-generic/device.h>
+
diff --git a/include/asm-mips/dma.h b/include/asm-mips/dma.h
index e85849a..23f789c 100644
--- a/include/asm-mips/dma.h
+++ b/include/asm-mips/dma.h
@@ -74,7 +74,9 @@
  *
  */
 
+#ifndef GENERIC_ISA_DMA_SUPPORT_BROKEN
 #define MAX_DMA_CHANNELS	8
+#endif
 
 /*
  * The maximum address in KSEG0 that we can perform a DMA transfer to on this
diff --git a/include/asm-mips/gt64120.h b/include/asm-mips/gt64120.h
index 2edd171..4bf8e28 100644
--- a/include/asm-mips/gt64120.h
+++ b/include/asm-mips/gt64120.h
@@ -451,6 +451,13 @@
 #define GT_SDRAM_OPMODE_OP_MODE		3
 #define GT_SDRAM_OPMODE_OP_CBR		4
 
+#define GT_TC_CONTROL_ENTC0_SHF		0
+#define GT_TC_CONTROL_ENTC0_MSK		(MSK(1) << GT_TC_CONTROL_ENTC0_SHF)
+#define GT_TC_CONTROL_ENTC0_BIT		GT_TC_CONTROL_ENTC0_MSK
+#define GT_TC_CONTROL_SELTC0_SHF	1
+#define GT_TC_CONTROL_SELTC0_MSK	(MSK(1) << GT_TC_CONTROL_SELTC0_SHF)
+#define GT_TC_CONTROL_SELTC0_BIT	GT_TC_CONTROL_SELTC0_MSK
+
 
 #define GT_PCI0_BARE_SWSCS3BOOTDIS_SHF	0
 #define GT_PCI0_BARE_SWSCS3BOOTDIS_MSK	(MSK(1) << GT_PCI0_BARE_SWSCS3BOOTDIS_SHF)
@@ -523,6 +530,13 @@
 #define GT_PCI0_CMD_SWORDSWAP_MSK	(MSK(1) << GT_PCI0_CMD_SWORDSWAP_SHF)
 #define GT_PCI0_CMD_SWORDSWAP_BIT	GT_PCI0_CMD_SWORDSWAP_MSK
 
+#define GT_INTR_T0EXP_SHF		8
+#define GT_INTR_T0EXP_MSK		(MSK(1) << GT_INTR_T0EXP_SHF)
+#define GT_INTR_T0EXP_BIT		GT_INTR_T0EXP_MSK
+#define GT_INTR_RETRYCTR0_SHF		20
+#define GT_INTR_RETRYCTR0_MSK		(MSK(1) << GT_INTR_RETRYCTR0_SHF)
+#define GT_INTR_RETRYCTR0_BIT		GT_INTR_RETRYCTR0_MSK
+
 /*
  *  Misc
  */
diff --git a/include/asm-mips/io.h b/include/asm-mips/io.h
index bc5f3c5..d77b657 100644
--- a/include/asm-mips/io.h
+++ b/include/asm-mips/io.h
@@ -113,7 +113,7 @@
  *     almost all conceivable cases a device driver should not be using
  *     this function
  */
-static inline unsigned long virt_to_phys(volatile void * address)
+static inline unsigned long virt_to_phys(volatile const void *address)
 {
 	return (unsigned long)address - PAGE_OFFSET;
 }
diff --git a/include/asm-mips/irq.h b/include/asm-mips/irq.h
index 35a05ca..6765708 100644
--- a/include/asm-mips/irq.h
+++ b/include/asm-mips/irq.h
@@ -24,8 +24,6 @@
 #define irq_canonicalize(irq) (irq)	/* Sane hardware, sane code ... */
 #endif
 
-extern asmlinkage unsigned int do_IRQ(unsigned int irq);
-
 #ifdef CONFIG_MIPS_MT_SMTC
 /*
  * Clear interrupt mask handling "backstop" if irq_hwmask
@@ -43,8 +41,6 @@
 #define __DO_IRQ_SMTC_HOOK() do { } while (0)
 #endif
 
-#ifdef CONFIG_PREEMPT
-
 /*
  * do_IRQ handles all normal device IRQ's (the special
  * SMP cross-CPU interrupts have their own specific
@@ -57,12 +53,10 @@
 do {									\
 	irq_enter();							\
 	__DO_IRQ_SMTC_HOOK();						\
-	__do_IRQ((irq));						\
+	generic_handle_irq(irq);					\
 	irq_exit();							\
 } while (0)
 
-#endif
-
 extern void arch_init_irq(void);
 extern void spurious_interrupt(void);
 
diff --git a/include/asm-mips/kexec.h b/include/asm-mips/kexec.h
new file mode 100644
index 0000000..b25267e
--- /dev/null
+++ b/include/asm-mips/kexec.h
@@ -0,0 +1,32 @@
+/*
+ * kexec.h for kexec
+ * Created by <nschichan@corp.free.fr> on Thu Oct 12 14:59:34 2006
+ *
+ * This source code is licensed under the GNU General Public License,
+ * Version 2.  See the file COPYING for more details.
+ */
+
+#ifndef _MIPS_KEXEC
+# define _MIPS_KEXEC
+
+/* Maximum physical address we can use pages from */
+#define KEXEC_SOURCE_MEMORY_LIMIT (0x20000000)
+/* Maximum address we can reach in physical address mode */
+#define KEXEC_DESTINATION_MEMORY_LIMIT (0x20000000)
+ /* Maximum address we can use for the control code buffer */
+#define KEXEC_CONTROL_MEMORY_LIMIT (0x20000000)
+
+#define KEXEC_CONTROL_CODE_SIZE 4096
+
+/* The native architecture */
+#define KEXEC_ARCH KEXEC_ARCH_MIPS
+
+#define MAX_NOTE_BYTES 1024
+
+static inline void crash_setup_regs(struct pt_regs *newregs,
+				    struct pt_regs *oldregs)
+{
+	/* Dummy implementation for now */
+}
+
+#endif /* !_MIPS_KEXEC */
diff --git a/include/asm-mips/mach-cobalt/cobalt.h b/include/asm-mips/mach-cobalt/cobalt.h
index b3c5ecb..00b0fc6 100644
--- a/include/asm-mips/mach-cobalt/cobalt.h
+++ b/include/asm-mips/mach-cobalt/cobalt.h
@@ -67,34 +67,9 @@
 #define COBALT_BRD_ID_QUBE2    0x5
 #define COBALT_BRD_ID_RAQ2     0x6
 
-/*
- * Galileo chipset access macros for the Cobalt. The base address for
- * the GT64111 chip is 0x14000000
- *
- * Most of this really should go into a separate GT64111 header file.
- */
-#define GT64111_IO_BASE		0x10000000UL
-#define GT64111_IO_END		0x11ffffffUL
-#define GT64111_MEM_BASE	0x12000000UL
-#define GT64111_MEM_END		0x13ffffffUL
-#define GT64111_BASE		0x14000000UL
-#define GALILEO_REG(ofs)	CKSEG1ADDR(GT64111_BASE + (unsigned long)(ofs))
-
-#define GALILEO_INL(port)	(*(volatile unsigned int *) GALILEO_REG(port))
-#define GALILEO_OUTL(val, port)						\
-do {									\
-	*(volatile unsigned int *) GALILEO_REG(port) = (val);		\
-} while (0)
-
-#define GALILEO_INTR_T0EXP	(1 << 8)
-#define GALILEO_INTR_RETRY_CTR	(1 << 20)
-
-#define GALILEO_ENTC0		0x01
-#define GALILEO_SELTC0		0x02
-
 #define PCI_CFG_SET(devfn,where)					\
-	GALILEO_OUTL((0x80000000 | (PCI_SLOT (devfn) << 11) |		\
-		(PCI_FUNC (devfn) << 8) | (where)), GT_PCI0_CFGADDR_OFS)
+	GT_WRITE(GT_PCI0_CFGADDR_OFS, (0x80000000 | (PCI_SLOT (devfn) << 11) |		\
+		(PCI_FUNC (devfn) << 8) | (where)))
 
 #define COBALT_LED_PORT		(*(volatile unsigned char *) CKSEG1ADDR(0x1c000000))
 # define COBALT_LED_BAR_LEFT	(1 << 0)	/* Qube */
diff --git a/include/asm-mips/mach-cobalt/mach-gt64120.h b/include/asm-mips/mach-cobalt/mach-gt64120.h
index 587fc43..ae9c552 100644
--- a/include/asm-mips/mach-cobalt/mach-gt64120.h
+++ b/include/asm-mips/mach-cobalt/mach-gt64120.h
@@ -1 +1,27 @@
-/* there's something here ... in the dark */
+/*
+ *  Copyright (C) 2006  Yoichi Yuasa <yoichi_yuasa@tripeaks.co.jp>
+ *
+ *  This program is free software; you can redistribute it and/or modify
+ *  it under the terms of the GNU General Public License as published by
+ *  the Free Software Foundation; either version 2 of the License, or
+ *  (at your option) any later version.
+ *
+ *  This program is distributed in the hope that it will be useful,
+ *  but WITHOUT ANY WARRANTY; without even the implied warranty of
+ *  MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ *  GNU General Public License for more details.
+ *
+ *  You should have received a copy of the GNU General Public License
+ *  along with this program; if not, write to the Free Software
+ *  Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston, MA  02110-1301  USA
+ */
+#ifndef _COBALT_MACH_GT64120_H
+#define _COBALT_MACH_GT64120_H
+
+/*
+ * Cobalt uses GT64111. GT64111 is almost the same as GT64120.
+ */
+
+#define GT64120_BASE	CKSEG1ADDR(GT_DEF_BASE)
+
+#endif /* _COBALT_MACH_GT64120_H */
diff --git a/include/asm-mips/mipsregs.h b/include/asm-mips/mipsregs.h
index 1f318d7..9985cb7 100644
--- a/include/asm-mips/mipsregs.h
+++ b/include/asm-mips/mipsregs.h
@@ -545,62 +545,6 @@
 #define MIPS_FPIR_L		(_ULCAST_(1) << 21)
 #define MIPS_FPIR_F64		(_ULCAST_(1) << 22)
 
-/*
- * R10000 performance counter definitions.
- *
- * FIXME: The R10000 performance counter opens a nice way to implement CPU
- *        time accounting with a precission of one cycle.  I don't have
- *        R10000 silicon but just a manual, so ...
- */
-
-/*
- * Events counted by counter #0
- */
-#define CE0_CYCLES			0
-#define CE0_INSN_ISSUED			1
-#define CE0_LPSC_ISSUED			2
-#define CE0_S_ISSUED			3
-#define CE0_SC_ISSUED			4
-#define CE0_SC_FAILED			5
-#define CE0_BRANCH_DECODED		6
-#define CE0_QW_WB_SECONDARY		7
-#define CE0_CORRECTED_ECC_ERRORS	8
-#define CE0_ICACHE_MISSES		9
-#define CE0_SCACHE_I_MISSES		10
-#define CE0_SCACHE_I_WAY_MISSPREDICTED	11
-#define CE0_EXT_INTERVENTIONS_REQ	12
-#define CE0_EXT_INVALIDATE_REQ		13
-#define CE0_VIRTUAL_COHERENCY_COND	14
-#define CE0_INSN_GRADUATED		15
-
-/*
- * Events counted by counter #1
- */
-#define CE1_CYCLES			0
-#define CE1_INSN_GRADUATED		1
-#define CE1_LPSC_GRADUATED		2
-#define CE1_S_GRADUATED			3
-#define CE1_SC_GRADUATED		4
-#define CE1_FP_INSN_GRADUATED		5
-#define CE1_QW_WB_PRIMARY		6
-#define CE1_TLB_REFILL			7
-#define CE1_BRANCH_MISSPREDICTED	8
-#define CE1_DCACHE_MISS			9
-#define CE1_SCACHE_D_MISSES		10
-#define CE1_SCACHE_D_WAY_MISSPREDICTED	11
-#define CE1_EXT_INTERVENTION_HITS	12
-#define CE1_EXT_INVALIDATE_REQ		13
-#define CE1_SP_HINT_TO_CEXCL_SC_BLOCKS	14
-#define CE1_SP_HINT_TO_SHARED_SC_BLOCKS	15
-
-/*
- * These flags define in which privilege mode the counters count events
- */
-#define CEB_USER	8	/* Count events in user mode, EXL = ERL = 0 */
-#define CEB_SUPERVISOR	4	/* Count events in supvervisor mode EXL = ERL = 0 */
-#define CEB_KERNEL	2	/* Count events in kernel mode EXL = ERL = 0 */
-#define CEB_EXL		1	/* Count events with EXL = 1, ERL = 0 */
-
 #ifndef __ASSEMBLY__
 
 /*
diff --git a/include/asm-mips/page.h b/include/asm-mips/page.h
index 85b258e..0dc1a45 100644
--- a/include/asm-mips/page.h
+++ b/include/asm-mips/page.h
@@ -34,7 +34,9 @@
 
 #ifndef __ASSEMBLY__
 
+#include <linux/pfn.h>
 #include <asm/cpu-features.h>
+#include <asm/io.h>
 
 extern void clear_page(void * page);
 extern void copy_page(void * to, void * from);
@@ -134,8 +136,14 @@
 /* to align the pointer to the (next) page boundary */
 #define PAGE_ALIGN(addr)	(((addr) + PAGE_SIZE - 1) & PAGE_MASK)
 
-#define __pa(x)			((unsigned long) (x) - PAGE_OFFSET)
-#define __va(x)			((void *)((unsigned long) (x) + PAGE_OFFSET))
+#if defined(CONFIG_64BIT) && !defined(CONFIG_BUILD_ELF64)
+#define __pa_page_offset(x)	((unsigned long)(x) < CKSEG0 ? PAGE_OFFSET : CKSEG0)
+#else
+#define __pa_page_offset(x)	PAGE_OFFSET
+#endif
+#define __pa(x)			((unsigned long)(x) - __pa_page_offset(x))
+#define __pa_symbol(x)		__pa(RELOC_HIDE((unsigned long)(x),0))
+#define __va(x)			((void *)((unsigned long)(x) + PAGE_OFFSET))
 
 #define pfn_to_kaddr(pfn)	__va((pfn) << PAGE_SHIFT)
 
@@ -160,8 +168,8 @@
 
 #endif
 
-#define virt_to_page(kaddr)	pfn_to_page(__pa(kaddr) >> PAGE_SHIFT)
-#define virt_addr_valid(kaddr)	pfn_valid(__pa(kaddr) >> PAGE_SHIFT)
+#define virt_to_page(kaddr)	pfn_to_page(PFN_DOWN(virt_to_phys(kaddr)))
+#define virt_addr_valid(kaddr)	pfn_valid(PFN_DOWN(virt_to_phys(kaddr)))
 
 #define VM_DATA_DEFAULT_FLAGS	(VM_READ | VM_WRITE | VM_EXEC | \
 				 VM_MAYREAD | VM_MAYWRITE | VM_MAYEXEC)
diff --git a/include/asm-mips/pgtable-64.h b/include/asm-mips/pgtable-64.h
index 7e73203..b9b1e86 100644
--- a/include/asm-mips/pgtable-64.h
+++ b/include/asm-mips/pgtable-64.h
@@ -14,6 +14,7 @@
 #include <asm/addrspace.h>
 #include <asm/page.h>
 #include <asm/cachectl.h>
+#include <asm/fixmap.h>
 
 #include <asm-generic/pgtable-nopud.h>
 
@@ -103,6 +104,13 @@
 #define VMALLOC_START		MAP_BASE
 #define VMALLOC_END	\
 	(VMALLOC_START + PTRS_PER_PGD * PTRS_PER_PMD * PTRS_PER_PTE * PAGE_SIZE)
+#if defined(CONFIG_MODULES) && !defined(CONFIG_BUILD_ELF64) && \
+	VMALLOC_START != CKSSEG
+/* Load modules into 32bit-compatible segment. */
+#define MODULE_START	CKSSEG
+#define MODULE_END	(FIXADDR_START-2*PAGE_SIZE)
+extern pgd_t module_pg_dir[PTRS_PER_PGD];
+#endif
 
 #define pte_ERROR(e) \
 	printk("%s:%d: bad pte %016lx.\n", __FILE__, __LINE__, pte_val(e))
@@ -174,7 +182,12 @@
 #define __pmd_offset(address)	pmd_index(address)
 
 /* to find an entry in a kernel page-table-directory */
+#ifdef MODULE_START
+#define pgd_offset_k(address) \
+	((address) >= MODULE_START ? module_pg_dir : pgd_offset(&init_mm, 0UL))
+#else
 #define pgd_offset_k(address) pgd_offset(&init_mm, 0UL)
+#endif
 
 #define pgd_index(address)	(((address) >> PGDIR_SHIFT) & (PTRS_PER_PGD-1))
 #define pmd_index(address)	(((address) >> PMD_SHIFT) & (PTRS_PER_PMD-1))
diff --git a/include/asm-mips/pgtable.h b/include/asm-mips/pgtable.h
index 1ca4d1e..f2e1325 100644
--- a/include/asm-mips/pgtable.h
+++ b/include/asm-mips/pgtable.h
@@ -67,7 +67,7 @@
 extern unsigned long zero_page_mask;
 
 #define ZERO_PAGE(vaddr) \
-	(virt_to_page(empty_zero_page + (((unsigned long)(vaddr)) & zero_page_mask)))
+	(virt_to_page((void *)(empty_zero_page + (((unsigned long)(vaddr)) & zero_page_mask))))
 
 #define __HAVE_ARCH_MOVE_PTE
 #define move_pte(pte, prot, old_addr, new_addr)				\
diff --git a/include/asm-mips/ptrace.h b/include/asm-mips/ptrace.h
index 5f3a907..30bf555 100644
--- a/include/asm-mips/ptrace.h
+++ b/include/asm-mips/ptrace.h
@@ -80,8 +80,6 @@
 #define instruction_pointer(regs) ((regs)->cp0_epc)
 #define profile_pc(regs) instruction_pointer(regs)
 
-extern void show_regs(struct pt_regs *);
-
 extern asmlinkage void do_syscall_trace(struct pt_regs *regs, int entryexit);
 
 #endif
diff --git a/include/asm-mips/time.h b/include/asm-mips/time.h
index 625acd3..a632cef 100644
--- a/include/asm-mips/time.h
+++ b/include/asm-mips/time.h
@@ -21,6 +21,7 @@
 #include <linux/ptrace.h>
 #include <linux/rtc.h>
 #include <linux/spinlock.h>
+#include <linux/clocksource.h>
 
 extern spinlock_t rtc_lock;
 
@@ -44,12 +45,10 @@
 extern void (*mips_timer_ack)(void);
 
 /*
- * High precision timer functions.
- * If mips_hpt_read is NULL, an R4k-compatible timer setup is attempted.
+ * High precision timer clocksource.
+ * If .read is NULL, an R4k-compatible timer setup is attempted.
  */
-extern unsigned int (*mips_hpt_read)(void);
-extern void (*mips_hpt_init)(void);
-extern unsigned int mips_hpt_mask;
+extern struct clocksource clocksource_mips;
 
 /*
  * to_tm() converts system time back to (year, mon, day, hour, min, sec).
diff --git a/include/asm-parisc/device.h b/include/asm-parisc/device.h
new file mode 100644
index 0000000..d8f9872
--- /dev/null
+++ b/include/asm-parisc/device.h
@@ -0,0 +1,7 @@
+/*
+ * Arch specific extensions to struct device
+ *
+ * This file is released under the GPLv2
+ */
+#include <asm-generic/device.h>
+
diff --git a/include/asm-parisc/dma.h b/include/asm-parisc/dma.h
index da2cf37..31ad0f0 100644
--- a/include/asm-parisc/dma.h
+++ b/include/asm-parisc/dma.h
@@ -17,10 +17,10 @@
 
 /*
 ** DMA_CHUNK_SIZE is used by the SCSI mid-layer to break up
-** (or rather not merge) DMA's into managable chunks.
+** (or rather not merge) DMAs into manageable chunks.
 ** On parisc, this is more of the software/tuning constraint
-** rather than the HW. I/O MMU allocation alogorithms can be
-** faster with smaller size is (to some degree).
+** rather than the HW. I/O MMU allocation algorithms can be
+** faster with smaller sizes (to some degree).
 */
 #define DMA_CHUNK_SIZE	(BITS_PER_LONG*PAGE_SIZE)
 
diff --git a/include/asm-parisc/pci.h b/include/asm-parisc/pci.h
index 7b8ad11..7b3be9a 100644
--- a/include/asm-parisc/pci.h
+++ b/include/asm-parisc/pci.h
@@ -149,7 +149,7 @@
 /*
 ** Most PCI devices (eg Tulip, NCR720) also export the same registers
 ** to both MMIO and I/O port space.  Due to poor performance of I/O Port
-** access under HP PCI bus adapters, strongly reccomend use of MMIO
+** access under HP PCI bus adapters, strongly recommend the use of MMIO
 ** address space.
 **
 ** While I'm at it more PA programming notes:
diff --git a/include/asm-parisc/ropes.h b/include/asm-parisc/ropes.h
index 5542dd0..007a8806 100644
--- a/include/asm-parisc/ropes.h
+++ b/include/asm-parisc/ropes.h
@@ -14,7 +14,7 @@
 #endif
 
 /*
-** The number of pdir entries to "free" before issueing
+** The number of pdir entries to "free" before issuing
 ** a read to PCOM register to flush out PCOM writes.
 ** Interacts with allocation granularity (ie 4 or 8 entries
 ** allocated and free'd/purged at a time might make this
diff --git a/include/asm-powerpc/device.h b/include/asm-powerpc/device.h
new file mode 100644
index 0000000..d8f9872
--- /dev/null
+++ b/include/asm-powerpc/device.h
@@ -0,0 +1,7 @@
+/*
+ * Arch specific extensions to struct device
+ *
+ * This file is released under the GPLv2
+ */
+#include <asm-generic/device.h>
+
diff --git a/include/asm-powerpc/pci.h b/include/asm-powerpc/pci.h
index 46afd29..721c97f0 100644
--- a/include/asm-powerpc/pci.h
+++ b/include/asm-powerpc/pci.h
@@ -62,19 +62,13 @@
 }
 
 #ifdef CONFIG_PPC64
-#define HAVE_ARCH_PCI_MWI 1
-static inline int pcibios_prep_mwi(struct pci_dev *dev)
-{
-	/*
-	 * We would like to avoid touching the cacheline size or MWI bit
-	 * but we cant do that with the current pcibios_prep_mwi 
-	 * interface. pSeries firmware sets the cacheline size (which is not
-	 * the cpu cacheline size in all cases) and hardware treats MWI 
-	 * the same as memory write. So we dont touch the cacheline size
-	 * here and allow the generic code to set the MWI bit.
-	 */
-	return 0;
-}
+
+/*
+ * We want to avoid touching the cacheline size or MWI bit.
+ * pSeries firmware sets the cacheline size (which is not the cpu cacheline
+ * size in all cases) and hardware treats MWI the same as memory write.
+ */
+#define PCI_DISABLE_MWI
 
 extern struct dma_mapping_ops pci_dma_ops;
 
diff --git a/include/asm-ppc/device.h b/include/asm-ppc/device.h
new file mode 100644
index 0000000..d8f9872
--- /dev/null
+++ b/include/asm-ppc/device.h
@@ -0,0 +1,7 @@
+/*
+ * Arch specific extensions to struct device
+ *
+ * This file is released under the GPLv2
+ */
+#include <asm-generic/device.h>
+
diff --git a/include/asm-s390/device.h b/include/asm-s390/device.h
new file mode 100644
index 0000000..d8f9872
--- /dev/null
+++ b/include/asm-s390/device.h
@@ -0,0 +1,7 @@
+/*
+ * Arch specific extensions to struct device
+ *
+ * This file is released under the GPLv2
+ */
+#include <asm-generic/device.h>
+
diff --git a/include/asm-sh/device.h b/include/asm-sh/device.h
new file mode 100644
index 0000000..d8f9872
--- /dev/null
+++ b/include/asm-sh/device.h
@@ -0,0 +1,7 @@
+/*
+ * Arch specific extensions to struct device
+ *
+ * This file is released under the GPLv2
+ */
+#include <asm-generic/device.h>
+
diff --git a/include/asm-sh64/device.h b/include/asm-sh64/device.h
new file mode 100644
index 0000000..d8f9872
--- /dev/null
+++ b/include/asm-sh64/device.h
@@ -0,0 +1,7 @@
+/*
+ * Arch specific extensions to struct device
+ *
+ * This file is released under the GPLv2
+ */
+#include <asm-generic/device.h>
+
diff --git a/include/asm-sparc/device.h b/include/asm-sparc/device.h
new file mode 100644
index 0000000..d8f9872
--- /dev/null
+++ b/include/asm-sparc/device.h
@@ -0,0 +1,7 @@
+/*
+ * Arch specific extensions to struct device
+ *
+ * This file is released under the GPLv2
+ */
+#include <asm-generic/device.h>
+
diff --git a/include/asm-sparc64/device.h b/include/asm-sparc64/device.h
new file mode 100644
index 0000000..d8f9872
--- /dev/null
+++ b/include/asm-sparc64/device.h
@@ -0,0 +1,7 @@
+/*
+ * Arch specific extensions to struct device
+ *
+ * This file is released under the GPLv2
+ */
+#include <asm-generic/device.h>
+
diff --git a/include/asm-sparc64/pci.h b/include/asm-sparc64/pci.h
index e1ea67b..ca65602 100644
--- a/include/asm-sparc64/pci.h
+++ b/include/asm-sparc64/pci.h
@@ -18,6 +18,8 @@
 
 #define PCI_IRQ_NONE		0xffffffff
 
+#define PCI_CACHE_LINE_BYTES	64
+
 static inline void pcibios_set_master(struct pci_dev *dev)
 {
 	/* No special bus mastering setup handling */
@@ -291,10 +293,6 @@
 			       enum pci_mmap_state mmap_state,
 			       int write_combine);
 
-/* Platform specific MWI support. */
-#define HAVE_ARCH_PCI_MWI
-extern int pcibios_prep_mwi(struct pci_dev *dev);
-
 extern void
 pcibios_resource_to_bus(struct pci_dev *dev, struct pci_bus_region *region,
 			struct resource *res);
diff --git a/include/asm-um/device.h b/include/asm-um/device.h
new file mode 100644
index 0000000..d8f9872
--- /dev/null
+++ b/include/asm-um/device.h
@@ -0,0 +1,7 @@
+/*
+ * Arch specific extensions to struct device
+ *
+ * This file is released under the GPLv2
+ */
+#include <asm-generic/device.h>
+
diff --git a/include/asm-v850/device.h b/include/asm-v850/device.h
new file mode 100644
index 0000000..d8f9872
--- /dev/null
+++ b/include/asm-v850/device.h
@@ -0,0 +1,7 @@
+/*
+ * Arch specific extensions to struct device
+ *
+ * This file is released under the GPLv2
+ */
+#include <asm-generic/device.h>
+
diff --git a/include/asm-x86_64/device.h b/include/asm-x86_64/device.h
new file mode 100644
index 0000000..3afa03f
--- /dev/null
+++ b/include/asm-x86_64/device.h
@@ -0,0 +1,15 @@
+/*
+ * Arch specific extensions to struct device
+ *
+ * This file is released under the GPLv2
+ */
+#ifndef _ASM_X86_64_DEVICE_H
+#define _ASM_X86_64_DEVICE_H
+
+struct dev_archdata {
+#ifdef CONFIG_ACPI
+	void	*acpi_handle;
+#endif
+};
+
+#endif /* _ASM_X86_64_DEVICE_H */
diff --git a/include/asm-xtensa/device.h b/include/asm-xtensa/device.h
new file mode 100644
index 0000000..d8f9872
--- /dev/null
+++ b/include/asm-xtensa/device.h
@@ -0,0 +1,7 @@
+/*
+ * Arch specific extensions to struct device
+ *
+ * This file is released under the GPLv2
+ */
+#include <asm-generic/device.h>
+
diff --git a/include/linux/blkdev.h b/include/linux/blkdev.h
index 7bfcde2..e1c7286 100644
--- a/include/linux/blkdev.h
+++ b/include/linux/blkdev.h
@@ -678,10 +678,11 @@
 extern void blk_run_queue(request_queue_t *);
 extern void blk_start_queueing(request_queue_t *);
 extern void blk_queue_activity_fn(request_queue_t *, activity_fn *, void *);
-extern int blk_rq_map_user(request_queue_t *, struct request *, void __user *, unsigned int);
-extern int blk_rq_unmap_user(struct bio *, unsigned int);
+extern int blk_rq_map_user(request_queue_t *, struct request *, void __user *, unsigned long);
+extern int blk_rq_unmap_user(struct request *);
 extern int blk_rq_map_kern(request_queue_t *, struct request *, void *, unsigned int, gfp_t);
-extern int blk_rq_map_user_iov(request_queue_t *, struct request *, struct sg_iovec *, int);
+extern int blk_rq_map_user_iov(request_queue_t *, struct request *,
+			       struct sg_iovec *, int, unsigned int);
 extern int blk_execute_rq(request_queue_t *, struct gendisk *,
 			  struct request *, int);
 extern void blk_execute_rq_nowait(request_queue_t *, struct gendisk *,
diff --git a/include/linux/blktrace_api.h b/include/linux/blktrace_api.h
index b99a714..3680ff9 100644
--- a/include/linux/blktrace_api.h
+++ b/include/linux/blktrace_api.h
@@ -50,6 +50,15 @@
 };
 
 /*
+ * Notify events.
+ */
+enum blktrace_notify {
+	__BLK_TN_PROCESS = 0,		/* establish pid/name mapping */
+	__BLK_TN_TIMESTAMP,		/* include system clock */
+};
+
+
+/*
  * Trace actions in full. Additionally, read or write is masked
  */
 #define BLK_TA_QUEUE		(__BLK_TA_QUEUE | BLK_TC_ACT(BLK_TC_QUEUE))
@@ -68,6 +77,9 @@
 #define BLK_TA_BOUNCE		(__BLK_TA_BOUNCE)
 #define BLK_TA_REMAP		(__BLK_TA_REMAP | BLK_TC_ACT(BLK_TC_QUEUE))
 
+#define BLK_TN_PROCESS		(__BLK_TN_PROCESS | BLK_TC_ACT(BLK_TC_NOTIFY))
+#define BLK_TN_TIMESTAMP	(__BLK_TN_TIMESTAMP | BLK_TC_ACT(BLK_TC_NOTIFY))
+
 #define BLK_IO_TRACE_MAGIC	0x65617400
 #define BLK_IO_TRACE_VERSION	0x07
 
diff --git a/include/linux/device.h b/include/linux/device.h
index 9d4f6a9..583a341 100644
--- a/include/linux/device.h
+++ b/include/linux/device.h
@@ -21,6 +21,7 @@
 #include <linux/pm.h>
 #include <asm/semaphore.h>
 #include <asm/atomic.h>
+#include <asm/device.h>
 
 #define DEVICE_NAME_SIZE	50
 #define DEVICE_NAME_HALF	__stringify(20)	/* Less than half to accommodate slop */
@@ -42,6 +43,8 @@
 	struct klist		klist_devices;
 	struct klist		klist_drivers;
 
+	struct blocking_notifier_head bus_notifier;
+
 	struct bus_attribute	* bus_attrs;
 	struct device_attribute	* dev_attrs;
 	struct driver_attribute	* drv_attrs;
@@ -75,6 +78,29 @@
 		struct device_driver *start, void *data,
 		int (*fn)(struct device_driver *, void *));
 
+/*
+ * Bus notifiers: Get notified of addition/removal of devices
+ * and binding/unbinding of drivers to devices.
+ * In the long run, it should be a replacement for the platform
+ * notify hooks.
+ */
+struct notifier_block;
+
+extern int bus_register_notifier(struct bus_type *bus,
+				 struct notifier_block *nb);
+extern int bus_unregister_notifier(struct bus_type *bus,
+				   struct notifier_block *nb);
+
+/* All 4 notifers below get called with the target struct device *
+ * as an argument. Note that those functions are likely to be called
+ * with the device semaphore held in the core, so be careful.
+ */
+#define BUS_NOTIFY_ADD_DEVICE		0x00000001 /* device added */
+#define BUS_NOTIFY_DEL_DEVICE		0x00000002 /* device removed */
+#define BUS_NOTIFY_BOUND_DRIVER		0x00000003 /* driver bound to device */
+#define BUS_NOTIFY_UNBIND_DRIVER	0x00000004 /* driver about to be
+						      unbound */
+
 /* driverfs interface for exporting bus attributes */
 
 struct bus_attribute {
@@ -343,8 +369,6 @@
 	void		*driver_data;	/* data private to the driver */
 	void		*platform_data;	/* Platform specific data, device
 					   core doesn't touch it */
-	void		*firmware_data; /* Firmware specific data (e.g. ACPI,
-					   BIOS data),reserved for device core*/
 	struct dev_pm_info	power;
 
 	u64		*dma_mask;	/* dma mask (if dma'able device) */
@@ -358,6 +382,8 @@
 
 	struct dma_coherent_mem	*dma_mem; /* internal for coherent mem
 					     override */
+	/* arch specific additions */
+	struct dev_archdata	archdata;
 
 	/* class_device migration path */
 	struct list_head	node;
@@ -395,7 +421,10 @@
 extern void device_del(struct device * dev);
 extern int device_for_each_child(struct device *, void *,
 		     int (*fn)(struct device *, void *));
+extern struct device *device_find_child(struct device *, void *data,
+					int (*match)(struct device *, void *));
 extern int device_rename(struct device *dev, char *new_name);
+extern int device_move(struct device *dev, struct device *new_parent);
 
 /*
  * Manual binding of a device to driver. See drivers/base/bus.c
@@ -415,8 +444,6 @@
 				    __attribute__((format(printf,4,5)));
 extern void device_destroy(struct class *cls, dev_t devt);
 
-extern int virtual_device_parent(struct device *dev);
-
 /*
  * Platform "fixup" functions - allow the platform to have their say
  * about devices and actions that the general device layer doesn't
diff --git a/include/linux/elevator.h b/include/linux/elevator.h
index 2fa9f11..a24931d 100644
--- a/include/linux/elevator.h
+++ b/include/linux/elevator.h
@@ -21,11 +21,11 @@
 typedef int (elevator_may_queue_fn) (request_queue_t *, int);
 
 typedef int (elevator_set_req_fn) (request_queue_t *, struct request *, gfp_t);
-typedef void (elevator_put_req_fn) (request_queue_t *, struct request *);
+typedef void (elevator_put_req_fn) (struct request *);
 typedef void (elevator_activate_req_fn) (request_queue_t *, struct request *);
 typedef void (elevator_deactivate_req_fn) (request_queue_t *, struct request *);
 
-typedef void *(elevator_init_fn) (request_queue_t *, elevator_t *);
+typedef void *(elevator_init_fn) (request_queue_t *);
 typedef void (elevator_exit_fn) (elevator_t *);
 
 struct elevator_ops
diff --git a/include/linux/fb.h b/include/linux/fb.h
index 3e69241..fa23e06 100644
--- a/include/linux/fb.h
+++ b/include/linux/fb.h
@@ -774,8 +774,8 @@
 #endif
 
 	struct fb_ops *fbops;
-	struct device *device;
-	struct class_device *class_device; /* sysfs per device attrs */
+	struct device *device;		/* This is the parent */
+	struct device *dev;		/* This is this fb device */
 	int class_flag;                    /* private sysfs flags */
 #ifdef CONFIG_FB_TILEBLITTING
 	struct fb_tile_ops *tileops;    /* Tile Blitting */
@@ -910,8 +910,8 @@
 /* drivers/video/fbsysfs.c */
 extern struct fb_info *framebuffer_alloc(size_t size, struct device *dev);
 extern void framebuffer_release(struct fb_info *info);
-extern int fb_init_class_device(struct fb_info *fb_info);
-extern void fb_cleanup_class_device(struct fb_info *head);
+extern int fb_init_device(struct fb_info *fb_info);
+extern void fb_cleanup_device(struct fb_info *head);
 extern void fb_bl_default_curve(struct fb_info *fb_info, u8 off, u8 min, u8 max);
 
 /* drivers/video/fbmon.c */
diff --git a/include/linux/ioport.h b/include/linux/ioport.h
index d42c833..cf8696d 100644
--- a/include/linux/ioport.h
+++ b/include/linux/ioport.h
@@ -89,6 +89,7 @@
 #define IORESOURCE_ROM_ENABLE		(1<<0)	/* ROM is enabled, same as PCI_ROM_ADDRESS_ENABLE */
 #define IORESOURCE_ROM_SHADOW		(1<<1)	/* ROM is copy at C000:0 */
 #define IORESOURCE_ROM_COPY		(1<<2)	/* ROM is alloc'd copy, resource field overlaid */
+#define IORESOURCE_ROM_BIOS_COPY	(1<<3)	/* ROM is BIOS copy, resource field overlaid */
 
 /* PC/ISA/whatever - the normal PC address spaces: IO and memory */
 extern struct resource ioport_resource;
diff --git a/include/linux/ixjuser.h b/include/linux/ixjuser.h
index fd1756d..88b4589 100644
--- a/include/linux/ixjuser.h
+++ b/include/linux/ixjuser.h
@@ -315,7 +315,7 @@
 * structures.  If the freq0 variable is non-zero, the tone table contents
 * for the tone_index are updated to the frequencies and gains defined.  It
 * should be noted that DTMF tones cannot be reassigned, so if DTMF tone
-* table indexs are used in a cadence the frequency and gain variables will
+* table indexes are used in a cadence the frequency and gain variables will
 * be ignored.
 *
 * If the array elements contain frequency parameters the driver will
diff --git a/include/linux/jiffies.h b/include/linux/jiffies.h
index c8d5f20..0ec6e28 100644
--- a/include/linux/jiffies.h
+++ b/include/linux/jiffies.h
@@ -74,7 +74,7 @@
 #define __jiffy_data  __attribute__((section(".data")))
 
 /*
- * The 64-bit value is not volatile - you MUST NOT read it
+ * The 64-bit value is not atomic - you MUST NOT read it
  * without sampling the sequence number in xtime_lock.
  * get_jiffies_64() will do this for you as appropriate.
  */
diff --git a/include/linux/kernel.h b/include/linux/kernel.h
index b9b5e4b..6738283 100644
--- a/include/linux/kernel.h
+++ b/include/linux/kernel.h
@@ -65,7 +65,7 @@
  * context (spinlock, irq-handler, ...).
  *
  * This is a useful debugging help to be able to catch problems early and not
- * be biten later when the calling function happens to sleep when it is not
+ * be bitten later when the calling function happens to sleep when it is not
  * supposed to.
  */
 #ifdef CONFIG_PREEMPT_VOLUNTARY
diff --git a/include/linux/kexec.h b/include/linux/kexec.h
index 6427949..a4ede62 100644
--- a/include/linux/kexec.h
+++ b/include/linux/kexec.h
@@ -122,6 +122,8 @@
 #define KEXEC_ARCH_IA_64   (50 << 16)
 #define KEXEC_ARCH_S390    (22 << 16)
 #define KEXEC_ARCH_SH      (42 << 16)
+#define KEXEC_ARCH_MIPS_LE (10 << 16)
+#define KEXEC_ARCH_MIPS    ( 8 << 16)
 
 #define KEXEC_FLAGS    (KEXEC_ON_CRASH)  /* List of defined/legal kexec flags */
 
diff --git a/include/linux/kobject.h b/include/linux/kobject.h
index bcd9cd1..d1c8d28 100644
--- a/include/linux/kobject.h
+++ b/include/linux/kobject.h
@@ -47,6 +47,7 @@
 	KOBJ_UMOUNT	= (__force kobject_action_t) 0x05,	/* umount event for block devices (broken) */
 	KOBJ_OFFLINE	= (__force kobject_action_t) 0x06,	/* device offline */
 	KOBJ_ONLINE	= (__force kobject_action_t) 0x07,	/* device online */
+	KOBJ_MOVE	= (__force kobject_action_t) 0x08,	/* device move */
 };
 
 struct kobject {
@@ -76,6 +77,7 @@
 extern void kobject_del(struct kobject *);
 
 extern int __must_check kobject_rename(struct kobject *, const char *new_name);
+extern int __must_check kobject_move(struct kobject *, struct kobject *);
 
 extern int __must_check kobject_register(struct kobject *);
 extern void kobject_unregister(struct kobject *);
@@ -264,6 +266,8 @@
 
 #if defined(CONFIG_HOTPLUG)
 void kobject_uevent(struct kobject *kobj, enum kobject_action action);
+void kobject_uevent_env(struct kobject *kobj, enum kobject_action action,
+			char *envp[]);
 
 int add_uevent_var(char **envp, int num_envp, int *cur_index,
 			char *buffer, int buffer_size, int *cur_len,
@@ -271,6 +275,10 @@
 	__attribute__((format (printf, 7, 8)));
 #else
 static inline void kobject_uevent(struct kobject *kobj, enum kobject_action action) { }
+static inline void kobject_uevent_env(struct kobject *kobj,
+				      enum kobject_action action,
+				      char *envp[])
+{ }
 
 static inline int add_uevent_var(char **envp, int num_envp, int *cur_index,
 				      char *buffer, int buffer_size, int *cur_len, 
diff --git a/include/linux/miscdevice.h b/include/linux/miscdevice.h
index b03cfb9..326da7d 100644
--- a/include/linux/miscdevice.h
+++ b/include/linux/miscdevice.h
@@ -31,15 +31,14 @@
 #define	HPET_MINOR	     228
 
 struct device;
-struct class_device;
 
 struct miscdevice  {
 	int minor;
 	const char *name;
 	const struct file_operations *fops;
 	struct list_head list;
-	struct device *dev;
-	struct class_device *class;
+	struct device *parent;
+	struct device *this_device;
 };
 
 extern int misc_register(struct miscdevice * misc);
diff --git a/include/linux/mmc/host.h b/include/linux/mmc/host.h
index 587264a..528e7d3 100644
--- a/include/linux/mmc/host.h
+++ b/include/linux/mmc/host.h
@@ -74,8 +74,8 @@
 struct device;
 
 struct mmc_host {
-	struct device		*dev;
-	struct class_device	class_dev;
+	struct device		*parent;
+	struct device		class_dev;
 	int			index;
 	const struct mmc_host_ops *ops;
 	unsigned int		f_min;
@@ -125,8 +125,8 @@
 	return (void *)host->private;
 }
 
-#define mmc_dev(x)	((x)->dev)
-#define mmc_hostname(x)	((x)->class_dev.class_id)
+#define mmc_dev(x)	((x)->parent)
+#define mmc_hostname(x)	((x)->class_dev.bus_id)
 
 extern int mmc_suspend_host(struct mmc_host *, pm_message_t);
 extern int mmc_resume_host(struct mmc_host *);
diff --git a/include/linux/module.h b/include/linux/module.h
index d1d00ce..9258ffd 100644
--- a/include/linux/module.h
+++ b/include/linux/module.h
@@ -264,6 +264,7 @@
 	struct module_attribute *modinfo_attrs;
 	const char *version;
 	const char *srcversion;
+	struct kobject *drivers_dir;
 
 	/* Exported symbols */
 	const struct kernel_symbol *syms;
diff --git a/include/linux/mqueue.h b/include/linux/mqueue.h
index 8db9d75..8b5a796 100644
--- a/include/linux/mqueue.h
+++ b/include/linux/mqueue.h
@@ -18,8 +18,6 @@
 #ifndef _LINUX_MQUEUE_H
 #define _LINUX_MQUEUE_H
 
-#include <linux/types.h>
-
 #define MQ_PRIO_MAX 	32768
 /* per-uid limit of kernel memory used by mqueue, in bytes */
 #define MQ_BYTES_MAX	819200
diff --git a/include/linux/pci.h b/include/linux/pci.h
index 09be0f8..01c7072 100644
--- a/include/linux/pci.h
+++ b/include/linux/pci.h
@@ -51,6 +51,7 @@
 #include <linux/list.h>
 #include <linux/compiler.h>
 #include <linux/errno.h>
+#include <asm/atomic.h>
 #include <linux/device.h>
 
 /* File state for mmap()s on /proc/bus/pci/X/Y */
@@ -159,7 +160,6 @@
 	unsigned int	transparent:1;	/* Transparent PCI bridge */
 	unsigned int	multifunction:1;/* Part of multi-function device */
 	/* keep track of device state */
-	unsigned int	is_enabled:1;	/* pci_enable_device has been called */
 	unsigned int	is_busmaster:1; /* device is busmaster */
 	unsigned int	no_msi:1;	/* device may not use msi */
 	unsigned int	no_d1d2:1;   /* only allow d0 or d3 */
@@ -167,6 +167,7 @@
 	unsigned int	broken_parity_status:1;	/* Device generates false positive parity */
 	unsigned int 	msi_enabled:1;
 	unsigned int	msix_enabled:1;
+	atomic_t	enable_cnt;	/* pci_enable_device has been called */
 
 	u32		saved_config_space[16]; /* config space saved at suspend time */
 	struct hlist_head saved_cap_space;
diff --git a/include/linux/pci_ids.h b/include/linux/pci_ids.h
index fa4e1d7..e060a76 100644
--- a/include/linux/pci_ids.h
+++ b/include/linux/pci_ids.h
@@ -2211,6 +2211,13 @@
 #define PCI_DEVICE_ID_INTEL_ICH8_4	0x2815
 #define PCI_DEVICE_ID_INTEL_ICH8_5	0x283e
 #define PCI_DEVICE_ID_INTEL_ICH8_6	0x2850
+#define PCI_DEVICE_ID_INTEL_ICH9_0	0x2910
+#define PCI_DEVICE_ID_INTEL_ICH9_1	0x2911
+#define PCI_DEVICE_ID_INTEL_ICH9_2	0x2912
+#define PCI_DEVICE_ID_INTEL_ICH9_3	0x2913
+#define PCI_DEVICE_ID_INTEL_ICH9_4	0x2914
+#define PCI_DEVICE_ID_INTEL_ICH9_5	0x2915
+#define PCI_DEVICE_ID_INTEL_ICH9_6	0x2930
 #define PCI_DEVICE_ID_INTEL_82855PM_HB	0x3340
 #define PCI_DEVICE_ID_INTEL_82830_HB	0x3575
 #define PCI_DEVICE_ID_INTEL_82830_CGC	0x3577
diff --git a/include/linux/pci_regs.h b/include/linux/pci_regs.h
index c321316..064b1dc 100644
--- a/include/linux/pci_regs.h
+++ b/include/linux/pci_regs.h
@@ -292,6 +292,12 @@
 #define PCI_MSI_DATA_64		12	/* 16 bits of data for 64-bit devices */
 #define PCI_MSI_MASK_BIT	16	/* Mask bits register */
 
+/* MSI-X registers (these are at offset PCI_MSI_FLAGS) */
+#define PCI_MSIX_FLAGS_QSIZE	0x7FF
+#define PCI_MSIX_FLAGS_ENABLE	(1 << 15)
+#define PCI_MSIX_FLAGS_BIRMASK	(7 << 0)
+#define PCI_MSIX_FLAGS_BITMASK	(1 << 0)
+
 /* CompactPCI Hotswap Register */
 
 #define PCI_CHSWP_CSR		2	/* Control and Status Register */
diff --git a/include/linux/platform_device.h b/include/linux/platform_device.h
index 29cd6de..20f47b8 100644
--- a/include/linux/platform_device.h
+++ b/include/linux/platform_device.h
@@ -58,6 +58,12 @@
 extern int platform_driver_register(struct platform_driver *);
 extern void platform_driver_unregister(struct platform_driver *);
 
+/* non-hotpluggable platform devices may use this so that probe() and
+ * its support may live in __init sections, conserving runtime memory.
+ */
+extern int platform_driver_probe(struct platform_driver *driver,
+		int (*probe)(struct platform_device *));
+
 #define platform_get_drvdata(_dev)	dev_get_drvdata(&(_dev)->dev)
 #define platform_set_drvdata(_dev,data)	dev_set_drvdata(&(_dev)->dev, (data))
 
diff --git a/include/linux/reiserfs_fs_sb.h b/include/linux/reiserfs_fs_sb.h
index 73e0bec..62a7169 100644
--- a/include/linux/reiserfs_fs_sb.h
+++ b/include/linux/reiserfs_fs_sb.h
@@ -429,7 +429,7 @@
 /* -o hash={tea, rupasov, r5, detect} is meant for properly mounting 
 ** reiserfs disks from 3.5.19 or earlier.  99% of the time, this option
 ** is not required.  If the normal autodection code can't determine which
-** hash to use (because both hases had the same value for a file)
+** hash to use (because both hashes had the same value for a file)
 ** use this option to force a specific hash.  It won't allow you to override
 ** the existing hash on the FS, so if you have a tea hash disk, and mount
 ** with -o hash=rupasov, the mount will fail.
diff --git a/include/linux/sysfs.h b/include/linux/sysfs.h
index 6d5c43d..2129d1b 100644
--- a/include/linux/sysfs.h
+++ b/include/linux/sysfs.h
@@ -97,6 +97,9 @@
 sysfs_rename_dir(struct kobject *, const char *new_name);
 
 extern int __must_check
+sysfs_move_dir(struct kobject *, struct kobject *);
+
+extern int __must_check
 sysfs_create_file(struct kobject *, const struct attribute *);
 
 extern int __must_check
@@ -142,6 +145,11 @@
 	return 0;
 }
 
+static inline int sysfs_move_dir(struct kobject * k, struct kobject * new_parent)
+{
+	return 0;
+}
+
 static inline int sysfs_create_file(struct kobject * k, const struct attribute * a)
 {
 	return 0;
diff --git a/include/linux/textsearch.h b/include/linux/textsearch.h
index 7dac8f0..004808a 100644
--- a/include/linux/textsearch.h
+++ b/include/linux/textsearch.h
@@ -20,7 +20,7 @@
 /**
  * struct ts_state - search state
  * @offset: offset for next match
- * @cb: control buffer, for persistant variables of get_next_block()
+ * @cb: control buffer, for persistent variables of get_next_block()
  */
 struct ts_state
 {
@@ -71,7 +71,7 @@
 	 * Called repeatedly until 0 is returned. Must assign the
 	 * head of the next block of data to &*dst and return the length
 	 * of the block or 0 if at the end. consumed == 0 indicates
-	 * a new search. May store/read persistant values in state->cb.
+	 * a new search. May store/read persistent values in state->cb.
 	 */
 	unsigned int		(*get_next_block)(unsigned int consumed,
 						  const u8 **dst,
diff --git a/include/linux/tty.h b/include/linux/tty.h
index 44091c0..65321f91 100644
--- a/include/linux/tty.h
+++ b/include/linux/tty.h
@@ -276,9 +276,8 @@
 extern int tty_unregister_ldisc(int disc);
 extern int tty_register_driver(struct tty_driver *driver);
 extern int tty_unregister_driver(struct tty_driver *driver);
-extern struct class_device *tty_register_device(struct tty_driver *driver,
-						unsigned index,
-						struct device *dev);
+extern struct device *tty_register_device(struct tty_driver *driver,
+					  unsigned index, struct device *dev);
 extern void tty_unregister_device(struct tty_driver *driver, unsigned index);
 extern int tty_read_raw_data(struct tty_struct *tty, unsigned char *bufp,
 			     int buflen);
diff --git a/include/linux/usb.h b/include/linux/usb.h
index 5482bfb..0cd73ed 100644
--- a/include/linux/usb.h
+++ b/include/linux/usb.h
@@ -313,8 +313,13 @@
 /* This is arbitrary.
  * From USB 2.0 spec Table 11-13, offset 7, a hub can
  * have up to 255 ports. The most yet reported is 10.
+ *
+ * Current Wireless USB host hardware (Intel i1480 for example) allows
+ * up to 22 devices to connect. Upcoming hardware might raise that
+ * limit. Because the arrays need to add a bit for hub status data, we
+ * do 31, so plus one evens out to four bytes.
  */
-#define USB_MAXCHILDREN		(16)
+#define USB_MAXCHILDREN		(31)
 
 struct usb_tt;
 
@@ -357,7 +362,8 @@
 	u8 portnum;			/* Parent port number (origin 1) */
 	u8 level;			/* Number of USB hub ancestors */
 
-	int have_langid;		/* whether string_langid is valid */
+	unsigned discon_suspended:1;	/* Disconnected while suspended */
+	unsigned have_langid:1;		/* whether string_langid is valid */
 	int string_langid;		/* language ID for strings */
 
 	/* static strings from the device */
@@ -410,14 +416,37 @@
 
 /* USB autosuspend and autoresume */
 #ifdef CONFIG_USB_SUSPEND
+extern int usb_autopm_set_interface(struct usb_interface *intf);
 extern int usb_autopm_get_interface(struct usb_interface *intf);
 extern void usb_autopm_put_interface(struct usb_interface *intf);
 
-#else
-#define usb_autopm_get_interface(intf)		0
-#define usb_autopm_put_interface(intf)		do {} while (0)
-#endif
+static inline void usb_autopm_enable(struct usb_interface *intf)
+{
+	intf->pm_usage_cnt = 0;
+	usb_autopm_set_interface(intf);
+}
 
+static inline void usb_autopm_disable(struct usb_interface *intf)
+{
+	intf->pm_usage_cnt = 1;
+	usb_autopm_set_interface(intf);
+}
+
+#else
+
+static inline int usb_autopm_set_interface(struct usb_interface *intf)
+{ return 0; }
+
+static inline int usb_autopm_get_interface(struct usb_interface *intf)
+{ return 0; }
+
+static inline void usb_autopm_put_interface(struct usb_interface *intf)
+{ }
+static inline void usb_autopm_enable(struct usb_interface *intf)
+{ }
+static inline void usb_autopm_disable(struct usb_interface *intf)
+{ }
+#endif
 
 /*-------------------------------------------------------------------------*/
 
@@ -490,17 +519,137 @@
 
 /*-------------------------------------------------------------------------*/
 
-extern int usb_endpoint_dir_in(const struct usb_endpoint_descriptor *epd);
-extern int usb_endpoint_dir_out(const struct usb_endpoint_descriptor *epd);
-extern int usb_endpoint_xfer_bulk(const struct usb_endpoint_descriptor *epd);
-extern int usb_endpoint_xfer_int(const struct usb_endpoint_descriptor *epd);
-extern int usb_endpoint_xfer_isoc(const struct usb_endpoint_descriptor *epd);
-extern int usb_endpoint_is_bulk_in(const struct usb_endpoint_descriptor *epd);
-extern int usb_endpoint_is_bulk_out(const struct usb_endpoint_descriptor *epd);
-extern int usb_endpoint_is_int_in(const struct usb_endpoint_descriptor *epd);
-extern int usb_endpoint_is_int_out(const struct usb_endpoint_descriptor *epd);
-extern int usb_endpoint_is_isoc_in(const struct usb_endpoint_descriptor *epd);
-extern int usb_endpoint_is_isoc_out(const struct usb_endpoint_descriptor *epd);
+/**
+ * usb_endpoint_dir_in - check if the endpoint has IN direction
+ * @epd: endpoint to be checked
+ *
+ * Returns true if the endpoint is of type IN, otherwise it returns false.
+ */
+static inline int usb_endpoint_dir_in(const struct usb_endpoint_descriptor *epd)
+{
+	return ((epd->bEndpointAddress & USB_ENDPOINT_DIR_MASK) == USB_DIR_IN);
+}
+
+/**
+ * usb_endpoint_dir_out - check if the endpoint has OUT direction
+ * @epd: endpoint to be checked
+ *
+ * Returns true if the endpoint is of type OUT, otherwise it returns false.
+ */
+static inline int usb_endpoint_dir_out(const struct usb_endpoint_descriptor *epd)
+{
+	return ((epd->bEndpointAddress & USB_ENDPOINT_DIR_MASK) == USB_DIR_OUT);
+}
+
+/**
+ * usb_endpoint_xfer_bulk - check if the endpoint has bulk transfer type
+ * @epd: endpoint to be checked
+ *
+ * Returns true if the endpoint is of type bulk, otherwise it returns false.
+ */
+static inline int usb_endpoint_xfer_bulk(const struct usb_endpoint_descriptor *epd)
+{
+	return ((epd->bmAttributes & USB_ENDPOINT_XFERTYPE_MASK) ==
+		USB_ENDPOINT_XFER_BULK);
+}
+
+/**
+ * usb_endpoint_xfer_int - check if the endpoint has interrupt transfer type
+ * @epd: endpoint to be checked
+ *
+ * Returns true if the endpoint is of type interrupt, otherwise it returns
+ * false.
+ */
+static inline int usb_endpoint_xfer_int(const struct usb_endpoint_descriptor *epd)
+{
+	return ((epd->bmAttributes & USB_ENDPOINT_XFERTYPE_MASK) ==
+		USB_ENDPOINT_XFER_INT);
+}
+
+/**
+ * usb_endpoint_xfer_isoc - check if the endpoint has isochronous transfer type
+ * @epd: endpoint to be checked
+ *
+ * Returns true if the endpoint is of type isochronous, otherwise it returns
+ * false.
+ */
+static inline int usb_endpoint_xfer_isoc(const struct usb_endpoint_descriptor *epd)
+{
+	return ((epd->bmAttributes & USB_ENDPOINT_XFERTYPE_MASK) ==
+		USB_ENDPOINT_XFER_ISOC);
+}
+
+/**
+ * usb_endpoint_is_bulk_in - check if the endpoint is bulk IN
+ * @epd: endpoint to be checked
+ *
+ * Returns true if the endpoint has bulk transfer type and IN direction,
+ * otherwise it returns false.
+ */
+static inline int usb_endpoint_is_bulk_in(const struct usb_endpoint_descriptor *epd)
+{
+	return (usb_endpoint_xfer_bulk(epd) && usb_endpoint_dir_in(epd));
+}
+
+/**
+ * usb_endpoint_is_bulk_out - check if the endpoint is bulk OUT
+ * @epd: endpoint to be checked
+ *
+ * Returns true if the endpoint has bulk transfer type and OUT direction,
+ * otherwise it returns false.
+ */
+static inline int usb_endpoint_is_bulk_out(const struct usb_endpoint_descriptor *epd)
+{
+	return (usb_endpoint_xfer_bulk(epd) && usb_endpoint_dir_out(epd));
+}
+
+/**
+ * usb_endpoint_is_int_in - check if the endpoint is interrupt IN
+ * @epd: endpoint to be checked
+ *
+ * Returns true if the endpoint has interrupt transfer type and IN direction,
+ * otherwise it returns false.
+ */
+static inline int usb_endpoint_is_int_in(const struct usb_endpoint_descriptor *epd)
+{
+	return (usb_endpoint_xfer_int(epd) && usb_endpoint_dir_in(epd));
+}
+
+/**
+ * usb_endpoint_is_int_out - check if the endpoint is interrupt OUT
+ * @epd: endpoint to be checked
+ *
+ * Returns true if the endpoint has interrupt transfer type and OUT direction,
+ * otherwise it returns false.
+ */
+static inline int usb_endpoint_is_int_out(const struct usb_endpoint_descriptor *epd)
+{
+	return (usb_endpoint_xfer_int(epd) && usb_endpoint_dir_out(epd));
+}
+
+/**
+ * usb_endpoint_is_isoc_in - check if the endpoint is isochronous IN
+ * @epd: endpoint to be checked
+ *
+ * Returns true if the endpoint has isochronous transfer type and IN direction,
+ * otherwise it returns false.
+ */
+static inline int usb_endpoint_is_isoc_in(const struct usb_endpoint_descriptor *epd)
+{
+	return (usb_endpoint_xfer_isoc(epd) && usb_endpoint_dir_in(epd));
+}
+
+/**
+ * usb_endpoint_is_isoc_out - check if the endpoint is isochronous OUT
+ * @epd: endpoint to be checked
+ *
+ * Returns true if the endpoint has isochronous transfer type and OUT direction,
+ * otherwise it returns false.
+ */
+static inline int usb_endpoint_is_isoc_out(const struct usb_endpoint_descriptor *epd)
+{
+	return (usb_endpoint_xfer_isoc(epd) && usb_endpoint_dir_out(epd));
+}
 
 /*-------------------------------------------------------------------------*/
 
diff --git a/include/rdma/ib_cm.h b/include/rdma/ib_cm.h
index c9b4738..5c07017 100644
--- a/include/rdma/ib_cm.h
+++ b/include/rdma/ib_cm.h
@@ -60,6 +60,7 @@
 };
 
 enum ib_cm_lap_state {
+	IB_CM_LAP_UNINIT,
 	IB_CM_LAP_IDLE,
 	IB_CM_LAP_SENT,
 	IB_CM_LAP_RCVD,
@@ -443,13 +444,20 @@
 		    u8 private_data_len);
 
 /**
- * ib_cm_establish - Forces a connection state to established.
+ * ib_cm_notify - Notifies the CM of an event reported to the consumer.
  * @cm_id: Connection identifier to transition to established.
+ * @event: Type of event.
  *
- * This routine should be invoked by users who receive messages on a
- * connected QP before an RTU has been received.
+ * This routine should be invoked by users to notify the CM of relevant
+ * communication events.  Events that should be reported to the CM and
+ * when to report them are:
+ *
+ * IB_EVENT_COMM_EST - Used when a message is received on a connected
+ *    QP before an RTU has been received.
+ * IB_EVENT_PATH_MIG - Notifies the CM that the connection has failed over
+ *   to the alternate path.
  */
-int ib_cm_establish(struct ib_cm_id *cm_id);
+int ib_cm_notify(struct ib_cm_id *cm_id, enum ib_event_type event);
 
 /**
  * ib_send_cm_rej - Sends a connection rejection message to the
diff --git a/include/rdma/ib_user_cm.h b/include/rdma/ib_user_cm.h
index 066c20b..37650af 100644
--- a/include/rdma/ib_user_cm.h
+++ b/include/rdma/ib_user_cm.h
@@ -38,7 +38,7 @@
 
 #include <rdma/ib_user_sa.h>
 
-#define IB_USER_CM_ABI_VERSION 4
+#define IB_USER_CM_ABI_VERSION 5
 
 enum {
 	IB_USER_CM_CMD_CREATE_ID,
@@ -46,7 +46,7 @@
 	IB_USER_CM_CMD_ATTR_ID,
 
 	IB_USER_CM_CMD_LISTEN,
-	IB_USER_CM_CMD_ESTABLISH,
+	IB_USER_CM_CMD_NOTIFY,
 
 	IB_USER_CM_CMD_SEND_REQ,
 	IB_USER_CM_CMD_SEND_REP,
@@ -117,8 +117,9 @@
 	__u32 reserved;
 };
 
-struct ib_ucm_establish {
+struct ib_ucm_notify {
 	__u32 id;
+	__u32 event;
 };
 
 struct ib_ucm_private_data {
diff --git a/include/sound/core.h b/include/sound/core.h
index fa1ca01..a994bea 100644
--- a/include/sound/core.h
+++ b/include/sound/core.h
@@ -132,6 +132,7 @@
 	int shutdown;			/* this card is going down */
 	int free_on_last_close;		/* free in context of file_release */
 	wait_queue_head_t shutdown_sleep;
+	struct device *parent;
 	struct device *dev;
 
 #ifdef CONFIG_PM
@@ -187,13 +188,14 @@
 	int device;			/* device number */
 	const struct file_operations *f_ops;	/* file operations */
 	void *private_data;		/* private data for f_ops->open */
-	struct class_device *class_dev;	/* class device for sysfs */
+	struct device *dev;		/* device for sysfs */
 };
 
 /* sound.c */
 
 extern int snd_major;
 extern int snd_ecards_limit;
+extern struct class *sound_class;
 
 void snd_request_card(int card);
 
@@ -203,7 +205,7 @@
 int snd_unregister_device(int type, struct snd_card *card, int dev);
 void *snd_lookup_minor_data(unsigned int minor, int type);
 int snd_add_device_sysfs_file(int type, struct snd_card *card, int dev,
-			      const struct class_device_attribute *attr);
+			      struct device_attribute *attr);
 
 #ifdef CONFIG_SND_OSSEMUL
 int snd_register_oss_device(int type, struct snd_card *card, int dev,
@@ -255,7 +257,7 @@
 int snd_card_file_remove(struct snd_card *card, struct file *file);
 
 #ifndef snd_card_set_dev
-#define snd_card_set_dev(card,devptr) ((card)->dev = (devptr))
+#define snd_card_set_dev(card,devptr) ((card)->parent = (devptr))
 #endif
 
 /* device.c */
diff --git a/init/Kconfig b/init/Kconfig
index 176f7e5..14d4846 100644
--- a/init/Kconfig
+++ b/init/Kconfig
@@ -249,6 +249,26 @@
 
 	  Say N if unsure.
 
+config SYSFS_DEPRECATED
+	bool "Create deprecated sysfs files"
+	default y
+	help
+	  This option creates deprecated symlinks such as the
+	  "device"-link, the <subsystem>:<name>-link, and the
+	  "bus"-link. It may also add deprecated key in the
+	  uevent environment.
+	  None of these features or values should be used today, as
+	  they export driver core implementation details to userspace
+	  or export properties which can't be kept stable across kernel
+	  releases.
+
+	  If enabled, this option will also move any device structures
+	  that belong to a class, back into the /sys/class heirachy, in
+	  order to support older versions of udev.
+
+	  If you are using a distro that was released in 2006 or later,
+	  it should be safe to say N here.
+
 config RELAY
 	bool "Kernel->user space relay support (formerly relayfs)"
 	help
diff --git a/kernel/module.c b/kernel/module.c
index f016656..45e01cb 100644
--- a/kernel/module.c
+++ b/kernel/module.c
@@ -1086,22 +1086,35 @@
 		goto out;
 	kobj_set_kset_s(&mod->mkobj, module_subsys);
 	mod->mkobj.mod = mod;
-	err = kobject_register(&mod->mkobj.kobj);
+
+	/* delay uevent until full sysfs population */
+	kobject_init(&mod->mkobj.kobj);
+	err = kobject_add(&mod->mkobj.kobj);
 	if (err)
 		goto out;
 
+	mod->drivers_dir = kobject_add_dir(&mod->mkobj.kobj, "drivers");
+	if (!mod->drivers_dir)
+		goto out_unreg;
+
 	err = module_param_sysfs_setup(mod, kparam, num_params);
 	if (err)
-		goto out_unreg;
+		goto out_unreg_drivers;
 
 	err = module_add_modinfo_attrs(mod);
 	if (err)
-		goto out_unreg;
+		goto out_unreg_param;
 
+	kobject_uevent(&mod->mkobj.kobj, KOBJ_ADD);
 	return 0;
 
+out_unreg_drivers:
+	kobject_unregister(mod->drivers_dir);
+out_unreg_param:
+	module_param_sysfs_remove(mod);
 out_unreg:
-	kobject_unregister(&mod->mkobj.kobj);
+	kobject_del(&mod->mkobj.kobj);
+	kobject_put(&mod->mkobj.kobj);
 out:
 	return err;
 }
@@ -1110,6 +1123,7 @@
 {
 	module_remove_modinfo_attrs(mod);
 	module_param_sysfs_remove(mod);
+	kobject_unregister(mod->drivers_dir);
 
 	kobject_unregister(&mod->mkobj.kobj);
 }
@@ -2275,11 +2289,14 @@
 
 void module_add_driver(struct module *mod, struct device_driver *drv)
 {
+	int no_warn;
+
 	if (!mod || !drv)
 		return;
 
-	/* Don't check return code; this call is idempotent */
-	sysfs_create_link(&drv->kobj, &mod->mkobj.kobj, "module");
+	/* Don't check return codes; these calls are idempotent */
+	no_warn = sysfs_create_link(&drv->kobj, &mod->mkobj.kobj, "module");
+	no_warn = sysfs_create_link(mod->drivers_dir, &drv->kobj, drv->name);
 }
 EXPORT_SYMBOL(module_add_driver);
 
@@ -2288,6 +2305,8 @@
 	if (!drv)
 		return;
 	sysfs_remove_link(&drv->kobj, "module");
+	if (drv->owner && drv->owner->drivers_dir)
+		sysfs_remove_link(drv->owner->drivers_dir, drv->name);
 }
 EXPORT_SYMBOL(module_remove_driver);
 
diff --git a/lib/kobject.c b/lib/kobject.c
index 7dd5c0e..744a4b1 100644
--- a/lib/kobject.c
+++ b/lib/kobject.c
@@ -311,6 +311,56 @@
 }
 
 /**
+ *	kobject_move - move object to another parent
+ *	@kobj:	object in question.
+ *	@new_parent: object's new parent
+ */
+
+int kobject_move(struct kobject *kobj, struct kobject *new_parent)
+{
+	int error;
+	struct kobject *old_parent;
+	const char *devpath = NULL;
+	char *devpath_string = NULL;
+	char *envp[2];
+
+	kobj = kobject_get(kobj);
+	if (!kobj)
+		return -EINVAL;
+	new_parent = kobject_get(new_parent);
+	if (!new_parent) {
+		error = -EINVAL;
+		goto out;
+	}
+	/* old object path */
+	devpath = kobject_get_path(kobj, GFP_KERNEL);
+	if (!devpath) {
+		error = -ENOMEM;
+		goto out;
+	}
+	devpath_string = kmalloc(strlen(devpath) + 15, GFP_KERNEL);
+	if (!devpath_string) {
+		error = -ENOMEM;
+		goto out;
+	}
+	sprintf(devpath_string, "DEVPATH_OLD=%s", devpath);
+	envp[0] = devpath_string;
+	envp[1] = NULL;
+	error = sysfs_move_dir(kobj, new_parent);
+	if (error)
+		goto out;
+	old_parent = kobj->parent;
+	kobj->parent = new_parent;
+	kobject_put(old_parent);
+	kobject_uevent_env(kobj, KOBJ_MOVE, envp);
+out:
+	kobject_put(kobj);
+	kfree(devpath_string);
+	kfree(devpath);
+	return error;
+}
+
+/**
  *	kobject_del - unlink kobject from hierarchy.
  * 	@kobj:	object.
  */
diff --git a/lib/kobject_uevent.c b/lib/kobject_uevent.c
index 7f20e7b..a192276 100644
--- a/lib/kobject_uevent.c
+++ b/lib/kobject_uevent.c
@@ -50,18 +50,22 @@
 		return "offline";
 	case KOBJ_ONLINE:
 		return "online";
+	case KOBJ_MOVE:
+		return "move";
 	default:
 		return NULL;
 	}
 }
 
 /**
- * kobject_uevent - notify userspace by ending an uevent
+ * kobject_uevent_env - send an uevent with environmental data
  *
- * @action: action that is happening (usually KOBJ_ADD and KOBJ_REMOVE)
+ * @action: action that is happening (usually KOBJ_MOVE)
  * @kobj: struct kobject that the action is happening to
+ * @envp_ext: pointer to environmental data
  */
-void kobject_uevent(struct kobject *kobj, enum kobject_action action)
+void kobject_uevent_env(struct kobject *kobj, enum kobject_action action,
+			char *envp_ext[])
 {
 	char **envp;
 	char *buffer;
@@ -76,6 +80,7 @@
 	char *seq_buff;
 	int i = 0;
 	int retval;
+	int j;
 
 	pr_debug("%s\n", __FUNCTION__);
 
@@ -134,7 +139,8 @@
 	scratch += sprintf (scratch, "DEVPATH=%s", devpath) + 1;
 	envp [i++] = scratch;
 	scratch += sprintf(scratch, "SUBSYSTEM=%s", subsystem) + 1;
-
+	for (j = 0; envp_ext && envp_ext[j]; j++)
+		envp[i++] = envp_ext[j];
 	/* just reserve the space, overwrite it after kset call has returned */
 	envp[i++] = seq_buff = scratch;
 	scratch += strlen("SEQNUM=18446744073709551616") + 1;
@@ -200,6 +206,20 @@
 	kfree(envp);
 	return;
 }
+
+EXPORT_SYMBOL_GPL(kobject_uevent_env);
+
+/**
+ * kobject_uevent - notify userspace by ending an uevent
+ *
+ * @action: action that is happening (usually KOBJ_ADD and KOBJ_REMOVE)
+ * @kobj: struct kobject that the action is happening to
+ */
+void kobject_uevent(struct kobject *kobj, enum kobject_action action)
+{
+	kobject_uevent_env(kobj, action, NULL);
+}
+
 EXPORT_SYMBOL_GPL(kobject_uevent);
 
 /**
diff --git a/lib/textsearch.c b/lib/textsearch.c
index 2cb4a43..98bcadc 100644
--- a/lib/textsearch.c
+++ b/lib/textsearch.c
@@ -40,7 +40,7 @@
  *       configuration according to the specified parameters.
  *   (3) User starts the search(es) by calling _find() or _next() to
  *       fetch subsequent occurrences. A state variable is provided
- *       to the algorihtm to store persistant variables.
+ *       to the algorihtm to store persistent variables.
  *   (4) Core eventually resets the search offset and forwards the find()
  *       request to the algorithm.
  *   (5) Algorithm calls get_next_block() provided by the user continously
diff --git a/net/wanrouter/af_wanpipe.c b/net/wanrouter/af_wanpipe.c
index 6f39faa..c205973 100644
--- a/net/wanrouter/af_wanpipe.c
+++ b/net/wanrouter/af_wanpipe.c
@@ -13,7 +13,7 @@
 * Due Credit:
 *               Wanpipe socket layer is based on Packet and 
 *               the X25 socket layers. The above sockets were 
-*               used for the specific use of Sangoma Technoloiges 
+*               used for the specific use of Sangoma Technologies 
 *               API programs. 
 *               Packet socket Authors: Ross Biro, Fred N. van Kempen and 
 *                                      Alan Cox.
@@ -23,7 +23,7 @@
 * Apr 25, 2000  Nenad Corbic     o Added the ability to send zero length packets.
 * Mar 13, 2000  Nenad Corbic	 o Added a tx buffer check via ioctl call.
 * Mar 06, 2000  Nenad Corbic     o Fixed the corrupt sock lcn problem.
-*                                  Server and client applicaton can run
+*                                  Server and client application can run
 *                                  simultaneously without conflicts.
 * Feb 29, 2000  Nenad Corbic     o Added support for PVC protocols, such as
 *                                  CHDLC, Frame Relay and HDLC API.
diff --git a/net/wanrouter/wanmain.c b/net/wanrouter/wanmain.c
index 9479659..316211d 100644
--- a/net/wanrouter/wanmain.c
+++ b/net/wanrouter/wanmain.c
@@ -3,7 +3,7 @@
 *
 *		This module is completely hardware-independent and provides
 *		the following common services for the WAN Link Drivers:
-*		 o WAN device managenment (registering, unregistering)
+*		 o WAN device management (registering, unregistering)
 *		 o Network interface management
 *		 o Physical connection management (dial-up, incoming calls)
 *		 o Logical connection management (switched virtual circuits)
diff --git a/security/selinux/avc.c b/security/selinux/avc.c
index a300702..74c0319 100644
--- a/security/selinux/avc.c
+++ b/security/selinux/avc.c
@@ -32,12 +32,7 @@
 #include "avc.h"
 #include "avc_ss.h"
 
-static const struct av_perm_to_string
-{
-  u16 tclass;
-  u32 value;
-  const char *name;
-} av_perm_to_string[] = {
+static const struct av_perm_to_string av_perm_to_string[] = {
 #define S_(c, v, s) { c, v, s },
 #include "av_perm_to_string.h"
 #undef S_
@@ -57,17 +52,21 @@
 #undef TE_
 #undef S_
 
-static const struct av_inherit
-{
-    u16 tclass;
-    const char **common_pts;
-    u32 common_base;
-} av_inherit[] = {
+static const struct av_inherit av_inherit[] = {
 #define S_(c, i, b) { c, common_##i##_perm_to_string, b },
 #include "av_inherit.h"
 #undef S_
 };
 
+const struct selinux_class_perm selinux_class_perm = {
+	av_perm_to_string,
+	ARRAY_SIZE(av_perm_to_string),
+	class_to_string,
+	ARRAY_SIZE(class_to_string),
+	av_inherit,
+	ARRAY_SIZE(av_inherit)
+};
+
 #define AVC_CACHE_SLOTS			512
 #define AVC_DEF_CACHE_THRESHOLD		512
 #define AVC_CACHE_RECLAIM		16
diff --git a/security/selinux/include/avc_ss.h b/security/selinux/include/avc_ss.h
index 450a283..ff869e8 100644
--- a/security/selinux/include/avc_ss.h
+++ b/security/selinux/include/avc_ss.h
@@ -10,5 +10,29 @@
 
 int avc_ss_reset(u32 seqno);
 
+struct av_perm_to_string
+{
+	u16 tclass;
+	u32 value;
+	const char *name;
+};
+
+struct av_inherit
+{
+	u16 tclass;
+	const char **common_pts;
+	u32 common_base;
+};
+
+struct selinux_class_perm
+{
+	const struct av_perm_to_string *av_perm_to_string;
+	u32 av_pts_len;
+	const char **class_to_string;
+	u32 cts_len;
+	const struct av_inherit *av_inherit;
+	u32 av_inherit_len;
+};
+
 #endif /* _SELINUX_AVC_SS_H_ */
 
diff --git a/security/selinux/ss/hashtab.c b/security/selinux/ss/hashtab.c
index 24e5ec9..77b530c 100644
--- a/security/selinux/ss/hashtab.c
+++ b/security/selinux/ss/hashtab.c
@@ -8,8 +8,8 @@
 #include <linux/errno.h>
 #include "hashtab.h"
 
-struct hashtab *hashtab_create(u32 (*hash_value)(struct hashtab *h, void *key),
-                               int (*keycmp)(struct hashtab *h, void *key1, void *key2),
+struct hashtab *hashtab_create(u32 (*hash_value)(struct hashtab *h, const void *key),
+                               int (*keycmp)(struct hashtab *h, const void *key1, const void *key2),
                                u32 size)
 {
 	struct hashtab *p;
@@ -71,7 +71,7 @@
 	return 0;
 }
 
-void *hashtab_search(struct hashtab *h, void *key)
+void *hashtab_search(struct hashtab *h, const void *key)
 {
 	u32 hvalue;
 	struct hashtab_node *cur;
diff --git a/security/selinux/ss/hashtab.h b/security/selinux/ss/hashtab.h
index 4cc8581..7e2ff3e 100644
--- a/security/selinux/ss/hashtab.h
+++ b/security/selinux/ss/hashtab.h
@@ -22,9 +22,9 @@
 	struct hashtab_node **htable;	/* hash table */
 	u32 size;			/* number of slots in hash table */
 	u32 nel;			/* number of elements in hash table */
-	u32 (*hash_value)(struct hashtab *h, void *key);
+	u32 (*hash_value)(struct hashtab *h, const void *key);
 					/* hash function */
-	int (*keycmp)(struct hashtab *h, void *key1, void *key2);
+	int (*keycmp)(struct hashtab *h, const void *key1, const void *key2);
 					/* key comparison function */
 };
 
@@ -39,8 +39,8 @@
  * Returns NULL if insufficent space is available or
  * the new hash table otherwise.
  */
-struct hashtab *hashtab_create(u32 (*hash_value)(struct hashtab *h, void *key),
-                               int (*keycmp)(struct hashtab *h, void *key1, void *key2),
+struct hashtab *hashtab_create(u32 (*hash_value)(struct hashtab *h, const void *key),
+                               int (*keycmp)(struct hashtab *h, const void *key1, const void *key2),
                                u32 size);
 
 /*
@@ -59,7 +59,7 @@
  * Returns NULL if no entry has the specified key or
  * the datum of the entry otherwise.
  */
-void *hashtab_search(struct hashtab *h, void *k);
+void *hashtab_search(struct hashtab *h, const void *k);
 
 /*
  * Destroys the specified hash table.
diff --git a/security/selinux/ss/services.c b/security/selinux/ss/services.c
index bfe1227..4088204 100644
--- a/security/selinux/ss/services.c
+++ b/security/selinux/ss/services.c
@@ -17,9 +17,13 @@
  *
  *      Added support for NetLabel
  *
+ * Updated: Chad Sellers <csellers@tresys.com>
+ *
+ *  Added validation of kernel classes and permissions
+ *
  * Copyright (C) 2006 Hewlett-Packard Development Company, L.P.
  * Copyright (C) 2004-2006 Trusted Computer Solutions, Inc.
- * Copyright (C) 2003 - 2004 Tresys Technology, LLC
+ * Copyright (C) 2003 - 2004, 2006 Tresys Technology, LLC
  * Copyright (C) 2003 Red Hat, Inc., James Morris <jmorris@redhat.com>
  *	This program is free software; you can redistribute it and/or modify
  *  	it under the terms of the GNU General Public License as published by
@@ -53,6 +57,11 @@
 extern void selnl_notify_policyload(u32 seqno);
 unsigned int policydb_loaded_version;
 
+/*
+ * This is declared in avc.c
+ */
+extern const struct selinux_class_perm selinux_class_perm;
+
 static DEFINE_RWLOCK(policy_rwlock);
 #define POLICY_RDLOCK read_lock(&policy_rwlock)
 #define POLICY_WRLOCK write_lock_irq(&policy_rwlock)
@@ -1019,86 +1028,112 @@
 }
 
 /*
- * Verify that each permission that is defined under the
- * existing policy is still defined with the same value
- * in the new policy.
+ * Verify that each kernel class that is defined in the
+ * policy is correct
  */
-static int validate_perm(void *key, void *datum, void *p)
+static int validate_classes(struct policydb *p)
 {
-	struct hashtab *h;
-	struct perm_datum *perdatum, *perdatum2;
-	int rc = 0;
+	int i, j;
+	struct class_datum *cladatum;
+	struct perm_datum *perdatum;
+	u32 nprim, tmp, common_pts_len, perm_val, pol_val;
+	u16 class_val;
+	const struct selinux_class_perm *kdefs = &selinux_class_perm;
+	const char *def_class, *def_perm, *pol_class;
+	struct symtab *perms;
 
-
-	h = p;
-	perdatum = datum;
-
-	perdatum2 = hashtab_search(h, key);
-	if (!perdatum2) {
-		printk(KERN_ERR "security:  permission %s disappeared",
-		       (char *)key);
-		rc = -ENOENT;
-		goto out;
-	}
-	if (perdatum->value != perdatum2->value) {
-		printk(KERN_ERR "security:  the value of permission %s changed",
-		       (char *)key);
-		rc = -EINVAL;
-	}
-out:
-	return rc;
-}
-
-/*
- * Verify that each class that is defined under the
- * existing policy is still defined with the same
- * attributes in the new policy.
- */
-static int validate_class(void *key, void *datum, void *p)
-{
-	struct policydb *newp;
-	struct class_datum *cladatum, *cladatum2;
-	int rc;
-
-	newp = p;
-	cladatum = datum;
-
-	cladatum2 = hashtab_search(newp->p_classes.table, key);
-	if (!cladatum2) {
-		printk(KERN_ERR "security:  class %s disappeared\n",
-		       (char *)key);
-		rc = -ENOENT;
-		goto out;
-	}
-	if (cladatum->value != cladatum2->value) {
-		printk(KERN_ERR "security:  the value of class %s changed\n",
-		       (char *)key);
-		rc = -EINVAL;
-		goto out;
-	}
-	if ((cladatum->comdatum && !cladatum2->comdatum) ||
-	    (!cladatum->comdatum && cladatum2->comdatum)) {
-		printk(KERN_ERR "security:  the inherits clause for the access "
-		       "vector definition for class %s changed\n", (char *)key);
-		rc = -EINVAL;
-		goto out;
-	}
-	if (cladatum->comdatum) {
-		rc = hashtab_map(cladatum->comdatum->permissions.table, validate_perm,
-		                 cladatum2->comdatum->permissions.table);
-		if (rc) {
-			printk(" in the access vector definition for class "
-			       "%s\n", (char *)key);
-			goto out;
+	for (i = 1; i < kdefs->cts_len; i++) {
+		def_class = kdefs->class_to_string[i];
+		if (i > p->p_classes.nprim) {
+			printk(KERN_INFO
+			       "security:  class %s not defined in policy\n",
+			       def_class);
+			continue;
+		}
+		pol_class = p->p_class_val_to_name[i-1];
+		if (strcmp(pol_class, def_class)) {
+			printk(KERN_ERR
+			       "security:  class %d is incorrect, found %s but should be %s\n",
+			       i, pol_class, def_class);
+			return -EINVAL;
 		}
 	}
-	rc = hashtab_map(cladatum->permissions.table, validate_perm,
-	                 cladatum2->permissions.table);
-	if (rc)
-		printk(" in access vector definition for class %s\n",
-		       (char *)key);
-out:
-	return rc;
+	for (i = 0; i < kdefs->av_pts_len; i++) {
+		class_val = kdefs->av_perm_to_string[i].tclass;
+		perm_val = kdefs->av_perm_to_string[i].value;
+		def_perm = kdefs->av_perm_to_string[i].name;
+		if (class_val > p->p_classes.nprim)
+			continue;
+		pol_class = p->p_class_val_to_name[class_val-1];
+		cladatum = hashtab_search(p->p_classes.table, pol_class);
+		BUG_ON(!cladatum);
+		perms = &cladatum->permissions;
+		nprim = 1 << (perms->nprim - 1);
+		if (perm_val > nprim) {
+			printk(KERN_INFO
+			       "security:  permission %s in class %s not defined in policy\n",
+			       def_perm, pol_class);
+			continue;
+		}
+		perdatum = hashtab_search(perms->table, def_perm);
+		if (perdatum == NULL) {
+			printk(KERN_ERR
+			       "security:  permission %s in class %s not found in policy\n",
+			       def_perm, pol_class);
+			return -EINVAL;
+		}
+		pol_val = 1 << (perdatum->value - 1);
+		if (pol_val != perm_val) {
+			printk(KERN_ERR
+			       "security:  permission %s in class %s has incorrect value\n",
+			       def_perm, pol_class);
+			return -EINVAL;
+		}
+	}
+	for (i = 0; i < kdefs->av_inherit_len; i++) {
+		class_val = kdefs->av_inherit[i].tclass;
+		if (class_val > p->p_classes.nprim)
+			continue;
+		pol_class = p->p_class_val_to_name[class_val-1];
+		cladatum = hashtab_search(p->p_classes.table, pol_class);
+		BUG_ON(!cladatum);
+		if (!cladatum->comdatum) {
+			printk(KERN_ERR
+			       "security:  class %s should have an inherits clause but does not\n",
+			       pol_class);
+			return -EINVAL;
+		}
+		tmp = kdefs->av_inherit[i].common_base;
+		common_pts_len = 0;
+		while (!(tmp & 0x01)) {
+			common_pts_len++;
+			tmp >>= 1;
+		}
+		perms = &cladatum->comdatum->permissions;
+		for (j = 0; j < common_pts_len; j++) {
+			def_perm = kdefs->av_inherit[i].common_pts[j];
+			if (j >= perms->nprim) {
+				printk(KERN_INFO
+				       "security:  permission %s in class %s not defined in policy\n",
+				       def_perm, pol_class);
+				continue;
+			}
+			perdatum = hashtab_search(perms->table, def_perm);
+			if (perdatum == NULL) {
+				printk(KERN_ERR
+				       "security:  permission %s in class %s not found in policy\n",
+				       def_perm, pol_class);
+				return -EINVAL;
+			}
+			if (perdatum->value != j + 1) {
+				printk(KERN_ERR
+				       "security:  permission %s in class %s has incorrect value\n",
+				       def_perm, pol_class);
+				return -EINVAL;
+			}
+		}
+	}
+	return 0;
 }
 
 /* Clone the SID into the new SID table. */
@@ -1243,6 +1278,16 @@
 			avtab_cache_destroy();
 			return -EINVAL;
 		}
+		/* Verify that the kernel defined classes are correct. */
+		if (validate_classes(&policydb)) {
+			printk(KERN_ERR
+			       "security:  the definition of a class is incorrect\n");
+			LOAD_UNLOCK;
+			sidtab_destroy(&sidtab);
+			policydb_destroy(&policydb);
+			avtab_cache_destroy();
+			return -EINVAL;
+		}
 		policydb_loaded_version = policydb.policyvers;
 		ss_initialized = 1;
 		seqno = ++latest_granting;
@@ -1265,10 +1310,10 @@
 
 	sidtab_init(&newsidtab);
 
-	/* Verify that the existing classes did not change. */
-	if (hashtab_map(policydb.p_classes.table, validate_class, &newpolicydb)) {
-		printk(KERN_ERR "security:  the definition of an existing "
-		       "class changed\n");
+	/* Verify that the kernel defined classes are correct. */
+	if (validate_classes(&newpolicydb)) {
+		printk(KERN_ERR
+		       "security:  the definition of a class is incorrect\n");
 		rc = -EINVAL;
 		goto err;
 	}
diff --git a/security/selinux/ss/symtab.c b/security/selinux/ss/symtab.c
index 24a10d3..837658a 100644
--- a/security/selinux/ss/symtab.c
+++ b/security/selinux/ss/symtab.c
@@ -9,9 +9,9 @@
 #include <linux/errno.h>
 #include "symtab.h"
 
-static unsigned int symhash(struct hashtab *h, void *key)
+static unsigned int symhash(struct hashtab *h, const void *key)
 {
-	char *p, *keyp;
+	const char *p, *keyp;
 	unsigned int size;
 	unsigned int val;
 
@@ -23,9 +23,9 @@
 	return val & (h->size - 1);
 }
 
-static int symcmp(struct hashtab *h, void *key1, void *key2)
+static int symcmp(struct hashtab *h, const void *key1, const void *key2)
 {
-	char *keyp1, *keyp2;
+	const char *keyp1, *keyp2;
 
 	keyp1 = key1;
 	keyp2 = key2;
diff --git a/sound/Kconfig b/sound/Kconfig
index e0d791a..95949b6 100644
--- a/sound/Kconfig
+++ b/sound/Kconfig
@@ -64,11 +64,11 @@
 
 source "sound/mips/Kconfig"
 
-# the following will depenend on the order of config.
+# the following will depend on the order of config.
 # here assuming USB is defined before ALSA
 source "sound/usb/Kconfig"
 
-# the following will depenend on the order of config.
+# the following will depend on the order of config.
 # here assuming PCMCIA is defined before ALSA
 source "sound/pcmcia/Kconfig"
 
diff --git a/sound/core/init.c b/sound/core/init.c
index 3058d62..6152a75 100644
--- a/sound/core/init.c
+++ b/sound/core/init.c
@@ -361,6 +361,8 @@
 		snd_printk(KERN_WARNING "unable to free card info\n");
 		/* Not fatal error */
 	}
+	if (card->dev)
+		device_unregister(card->dev);
 	kfree(card);
 	return 0;
 }
@@ -495,6 +497,12 @@
 	int err;
 
 	snd_assert(card != NULL, return -EINVAL);
+	if (!card->dev) {
+		card->dev = device_create(sound_class, card->parent, 0,
+					  "card%i", card->number);
+		if (IS_ERR(card->dev))
+			card->dev = NULL;
+	}
 	if ((err = snd_device_register_all(card)) < 0)
 		return err;
 	mutex_lock(&snd_card_mutex);
diff --git a/sound/core/pcm.c b/sound/core/pcm.c
index fbbbcd2..5ac6e19 100644
--- a/sound/core/pcm.c
+++ b/sound/core/pcm.c
@@ -910,7 +910,8 @@
 	substream->pstr->substream_opened--;
 }
 
-static ssize_t show_pcm_class(struct class_device *class_device, char *buf)
+static ssize_t show_pcm_class(struct device *dev,
+			      struct device_attribute *attr, char *buf)
 {
 	struct snd_pcm *pcm;
 	const char *str;
@@ -921,7 +922,7 @@
 		[SNDRV_PCM_CLASS_DIGITIZER] = "digitizer",
 	};
 
-	if (! (pcm = class_get_devdata(class_device)) ||
+	if (! (pcm = dev_get_drvdata(dev)) ||
 	    pcm->dev_class > SNDRV_PCM_CLASS_LAST)
 		str = "none";
 	else
@@ -929,7 +930,7 @@
         return snprintf(buf, PAGE_SIZE, "%s\n", str);
 }
 
-static struct class_device_attribute pcm_attrs =
+static struct device_attribute pcm_attrs =
 	__ATTR(pcm_class, S_IRUGO, show_pcm_class, NULL);
 
 static int snd_pcm_dev_register(struct snd_device *device)
diff --git a/sound/core/sound.c b/sound/core/sound.c
index efa476c..2827420 100644
--- a/sound/core/sound.c
+++ b/sound/core/sound.c
@@ -61,9 +61,6 @@
 static struct snd_minor *snd_minors[SNDRV_OS_MINORS];
 static DEFINE_MUTEX(sound_mutex);
 
-extern struct class *sound_class;
-
-
 #ifdef CONFIG_KMOD
 
 /**
@@ -268,11 +265,10 @@
 	snd_minors[minor] = preg;
 	if (card)
 		device = card->dev;
-	preg->class_dev = class_device_create(sound_class, NULL,
-					      MKDEV(major, minor),
-					      device, "%s", name);
-	if (preg->class_dev)
-		class_set_devdata(preg->class_dev, private_data);
+	preg->dev = device_create(sound_class, device, MKDEV(major, minor),
+				  "%s", name);
+	if (preg->dev)
+		dev_set_drvdata(preg->dev, private_data);
 
 	mutex_unlock(&sound_mutex);
 	return 0;
@@ -320,7 +316,7 @@
 		return -EINVAL;
 	}
 
-	class_device_destroy(sound_class, MKDEV(major, minor));
+	device_destroy(sound_class, MKDEV(major, minor));
 
 	kfree(snd_minors[minor]);
 	snd_minors[minor] = NULL;
@@ -331,15 +327,15 @@
 EXPORT_SYMBOL(snd_unregister_device);
 
 int snd_add_device_sysfs_file(int type, struct snd_card *card, int dev,
-			      const struct class_device_attribute *attr)
+			      struct device_attribute *attr)
 {
 	int minor, ret = -EINVAL;
-	struct class_device *cdev;
+	struct device *d;
 
 	mutex_lock(&sound_mutex);
 	minor = find_snd_minor(type, card, dev);
-	if (minor >= 0 && (cdev = snd_minors[minor]->class_dev) != NULL)
-		ret = class_device_create_file(cdev, attr);
+	if (minor >= 0 && (d = snd_minors[minor]->dev) != NULL)
+		ret = device_create_file(d, attr);
 	mutex_unlock(&sound_mutex);
 	return ret;
 
diff --git a/sound/oss/cs46xx.c b/sound/oss/cs46xx.c
index 6e3c41f..b1c5d82 100644
--- a/sound/oss/cs46xx.c
+++ b/sound/oss/cs46xx.c
@@ -779,7 +779,7 @@
 		rate = 48000 / 9;
 
 	/*
-	 *  We can not capture at at rate greater than the Input Rate (48000).
+	 *  We cannot capture at at rate greater than the Input Rate (48000).
 	 *  Return an error if an attempt is made to stray outside that limit.
 	 */
 	if (rate > 48000)
@@ -4754,8 +4754,8 @@
 	mdelay(5 * cs_laptop_wait);		/* Shouldnt be needed ?? */
 	
 /*
-* If we are resuming under 2.2.x then we can not schedule a timeout.
-* so, just spin the CPU.
+* If we are resuming under 2.2.x then we cannot schedule a timeout,
+* so just spin the CPU.
 */
 	if (card->pm.flags & CS46XX_PM_IDLE) {
 	/*
diff --git a/sound/oss/soundcard.c b/sound/oss/soundcard.c
index 2344d09..75c5e74 100644
--- a/sound/oss/soundcard.c
+++ b/sound/oss/soundcard.c
@@ -557,17 +557,17 @@
 	sound_dmap_flag = (dmabuf > 0 ? 1 : 0);
 
 	for (i = 0; i < sizeof (dev_list) / sizeof *dev_list; i++) {
-		class_device_create(sound_class, NULL,
-				    MKDEV(SOUND_MAJOR, dev_list[i].minor),
-				    NULL, "%s", dev_list[i].name);
+		device_create(sound_class, NULL,
+			      MKDEV(SOUND_MAJOR, dev_list[i].minor),
+			      "%s", dev_list[i].name);
 
 		if (!dev_list[i].num)
 			continue;
 
 		for (j = 1; j < *dev_list[i].num; j++)
-			class_device_create(sound_class, NULL,
-					    MKDEV(SOUND_MAJOR, dev_list[i].minor + (j*0x10)),
-					    NULL, "%s%d", dev_list[i].name, j);
+			device_create(sound_class, NULL,
+				      MKDEV(SOUND_MAJOR, dev_list[i].minor + (j*0x10)),
+				      "%s%d", dev_list[i].name, j);
 	}
 
 	if (sound_nblocks >= 1024)
@@ -581,11 +581,11 @@
 	int i, j;
 
 	for (i = 0; i < sizeof (dev_list) / sizeof *dev_list; i++) {
-		class_device_destroy(sound_class, MKDEV(SOUND_MAJOR, dev_list[i].minor));
+		device_destroy(sound_class, MKDEV(SOUND_MAJOR, dev_list[i].minor));
 		if (!dev_list[i].num)
 			continue;
 		for (j = 1; j < *dev_list[i].num; j++)
-			class_device_destroy(sound_class, MKDEV(SOUND_MAJOR, dev_list[i].minor + (j*0x10)));
+			device_destroy(sound_class, MKDEV(SOUND_MAJOR, dev_list[i].minor + (j*0x10)));
 	}
 	
 	unregister_sound_special(1);
diff --git a/sound/sound_core.c b/sound/sound_core.c
index 5322c50..8f1ced4 100644
--- a/sound/sound_core.c
+++ b/sound/sound_core.c
@@ -170,8 +170,8 @@
 	else
 		sprintf(s->name, "sound/%s%d", name, r / SOUND_STEP);
 
-	class_device_create(sound_class, NULL, MKDEV(SOUND_MAJOR, s->unit_minor),
-			    dev, s->name+6);
+	device_create(sound_class, dev, MKDEV(SOUND_MAJOR, s->unit_minor),
+		      s->name+6);
 	return r;
 
  fail:
@@ -193,7 +193,7 @@
 	p = __sound_remove_unit(list, unit);
 	spin_unlock(&sound_loader_lock);
 	if (p) {
-		class_device_destroy(sound_class, MKDEV(SOUND_MAJOR, p->unit_minor));
+		device_destroy(sound_class, MKDEV(SOUND_MAJOR, p->unit_minor));
 		kfree(p);
 	}
 }
diff --git a/sound/usb/usbmidi.c b/sound/usb/usbmidi.c
index b7c5e59..24f5a26 100644
--- a/sound/usb/usbmidi.c
+++ b/sound/usb/usbmidi.c
@@ -981,7 +981,7 @@
 			if (umidi->usb_protocol_ops->finish_out_endpoint)
 				umidi->usb_protocol_ops->finish_out_endpoint(ep->out);
 		}
-		if (ep->in && ep->in->urb)
+		if (ep->in)
 			usb_kill_urb(ep->in->urb);
 	}
 }
diff --git a/sound/usb/usbmixer.c b/sound/usb/usbmixer.c
index 1024c17..e74eb1b 100644
--- a/sound/usb/usbmixer.c
+++ b/sound/usb/usbmixer.c
@@ -1620,8 +1620,7 @@
 		kfree(mixer->urb->transfer_buffer);
 		usb_free_urb(mixer->urb);
 	}
-	if (mixer->rc_urb)
-		usb_free_urb(mixer->rc_urb);
+	usb_free_urb(mixer->rc_urb);
 	kfree(mixer->rc_setup_packet);
 	kfree(mixer);
 }
@@ -2056,8 +2055,6 @@
 	struct usb_mixer_interface *mixer;
 	
 	mixer = list_entry(p, struct usb_mixer_interface, list);
-	if (mixer->urb)
-		usb_kill_urb(mixer->urb);
-	if (mixer->rc_urb)
-		usb_kill_urb(mixer->rc_urb);
+	usb_kill_urb(mixer->urb);
+	usb_kill_urb(mixer->rc_urb);
 }