blob: 4f21f42d096bad6737343318c64d45a802cffa77 [file] [log] [blame]
/*
* Copyright 2000 MontaVista Software Inc.
* Author: MontaVista Software, Inc.
* ppopov@mvista.com or source@mvista.com
*
* Updates to 2.6, Pete Popov, Embedded Alley Solutions, Inc.
*
* This program is free software; you can redistribute it and/or modify it
* under the terms of the GNU General Public License as published by the
* Free Software Foundation; either version 2 of the License, or (at your
* option) any later version.
*
* THIS SOFTWARE IS PROVIDED ``AS IS'' AND ANY EXPRESS OR IMPLIED
* WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF
* MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN
* NO EVENT SHALL THE AUTHOR BE LIABLE FOR ANY DIRECT, INDIRECT,
* INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT
* NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF
* USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON
* ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT
* (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF
* THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
*
* You should have received a copy of the GNU General Public License along
* with this program; if not, write to the Free Software Foundation, Inc.,
* 675 Mass Ave, Cambridge, MA 02139, USA.
*/
#include <linux/config.h>
#include <linux/init.h>
#include <linux/sched.h>
#include <linux/ioport.h>
#include <linux/mm.h>
#include <linux/delay.h>
#include <linux/interrupt.h>
#include <linux/module.h>
#include <asm/cpu.h>
#include <asm/bootinfo.h>
#include <asm/irq.h>
#include <asm/mipsregs.h>
#include <asm/reboot.h>
#include <asm/pgtable.h>
#include <asm/mach-au1x00/au1000.h>
#include <asm/time.h>
extern char * __init prom_getcmdline(void);
extern void __init board_setup(void);
extern void au1000_restart(char *);
extern void au1000_halt(void);
extern void au1000_power_off(void);
extern struct resource ioport_resource;
extern struct resource iomem_resource;
extern void (*board_time_init)(void);
extern void au1x_time_init(void);
extern void (*board_timer_setup)(struct irqaction *irq);
extern void au1x_timer_setup(struct irqaction *irq);
extern void au1xxx_time_init(void);
extern void au1xxx_timer_setup(struct irqaction *irq);
extern void set_cpuspec(void);
void __init plat_setup(void)
{
struct cpu_spec *sp;
char *argptr;
unsigned long prid, cpupll, bclk = 1;
set_cpuspec();
sp = cur_cpu_spec[0];
board_setup(); /* board specific setup */
prid = read_c0_prid();
cpupll = (au_readl(0xB1900060) & 0x3F) * 12;
printk("(PRId %08lx) @ %ldMHZ\n", prid, cpupll);
bclk = sp->cpu_bclk;
if (bclk)
{
/* Enable BCLK switching */
bclk = au_readl(0xB190003C);
au_writel(bclk | 0x60, 0xB190003C);
printk("BCLK switching enabled!\n");
}
if (sp->cpu_od) {
/* Various early Au1000 Errata corrected by this */
set_c0_config(1<<19); /* Set Config[OD] */
}
else {
/* Clear to obtain best system bus performance */
clear_c0_config(1<<19); /* Clear Config[OD] */
}
argptr = prom_getcmdline();
#ifdef CONFIG_SERIAL_AU1X00_CONSOLE
if ((argptr = strstr(argptr, "console=")) == NULL) {
argptr = prom_getcmdline();
strcat(argptr, " console=ttyS0,115200");
}
#endif
#ifdef CONFIG_FB_AU1100
if ((argptr = strstr(argptr, "video=")) == NULL) {
argptr = prom_getcmdline();
/* default panel */
/*strcat(argptr, " video=au1100fb:panel:Sharp_320x240_16");*/
#ifdef CONFIG_MIPS_HYDROGEN3
strcat(argptr, " video=au1100fb:panel:Hydrogen_3_NEC_panel_320x240,nohwcursor");
#endif
}
#endif
#ifdef CONFIG_FB_XPERT98
if ((argptr = strstr(argptr, "video=")) == NULL) {
argptr = prom_getcmdline();
strcat(argptr, " video=atyfb:1024x768-8@70");
}
#endif
#if defined(CONFIG_SOUND_AU1X00) && !defined(CONFIG_SOC_AU1000)
/* au1000 does not support vra, au1500 and au1100 do */
strcat(argptr, " au1000_audio=vra");
argptr = prom_getcmdline();
#endif
_machine_restart = au1000_restart;
_machine_halt = au1000_halt;
_machine_power_off = au1000_power_off;
board_time_init = au1xxx_time_init;
board_timer_setup = au1xxx_timer_setup;
/* IO/MEM resources. */
set_io_port_base(0);
ioport_resource.start = IOPORT_RESOURCE_START;
ioport_resource.end = IOPORT_RESOURCE_END;
iomem_resource.start = IOMEM_RESOURCE_START;
iomem_resource.end = IOMEM_RESOURCE_END;
while (au_readl(SYS_COUNTER_CNTRL) & SYS_CNTRL_E0S);
au_writel(SYS_CNTRL_E0 | SYS_CNTRL_EN0, SYS_COUNTER_CNTRL);
au_sync();
while (au_readl(SYS_COUNTER_CNTRL) & SYS_CNTRL_T0S);
au_writel(0, SYS_TOYTRIM);
}
#if defined(CONFIG_64BIT_PHYS_ADDR)
/* This routine should be valid for all Au1x based boards */
phys_t __fixup_bigphys_addr(phys_t phys_addr, phys_t size)
{
u32 start, end;
/* Don't fixup 36 bit addresses */
if ((phys_addr >> 32) != 0) return phys_addr;
#ifdef CONFIG_PCI
start = (u32)Au1500_PCI_MEM_START;
end = (u32)Au1500_PCI_MEM_END;
/* check for pci memory window */
if ((phys_addr >= start) && ((phys_addr + size) < end)) {
return (phys_t)((phys_addr - start) + Au1500_PCI_MEM_START);
}
#endif
/* All Au1x SOCs have a pcmcia controller */
/* We setup our 32 bit pseudo addresses to be equal to the
* 36 bit addr >> 4, to make it easier to check the address
* and fix it.
* The Au1x socket 0 phys attribute address is 0xF 4000 0000.
* The pseudo address we use is 0xF400 0000. Any address over
* 0xF400 0000 is a pcmcia pseudo address.
*/
if ((phys_addr >= 0xF4000000) && (phys_addr < 0xFFFFFFFF)) {
return (phys_t)(phys_addr << 4);
}
/* default nop */
return phys_addr;
}
EXPORT_SYMBOL(__fixup_bigphys_addr);
#endif