USB: dwc3: msm: Implement new initialization sequence
Currently dwc3-msm driver is not following the initialization
sequence as per new hardware programming guide. Hence implement
new initialization sequence. The new sequence does PHY reset
under GCTL reset
This change solves the USB enumeration issue seen with HS/LS devices
connect/disconnect over TI USB3.0 HUB.
CRs-Fixed: 477323
CRs-Fixed: 515048
Change-Id: Ia0500517290c82f6ca6dc9dc32b4cee1e4f44aff
Signed-off-by: Vijayavardhan Vennapusa <vvreddy@codeaurora.org>
diff --git a/drivers/usb/dwc3/dwc3_otg.c b/drivers/usb/dwc3/dwc3_otg.c
index d0d9d34..e912e86 100644
--- a/drivers/usb/dwc3/dwc3_otg.c
+++ b/drivers/usb/dwc3/dwc3_otg.c
@@ -56,6 +56,19 @@
reg = dwc3_readl(dwc->regs, DWC3_GCTL);
reg &= ~(DWC3_GCTL_PRTCAPDIR(DWC3_GCTL_PRTCAP_OTG));
reg |= DWC3_GCTL_PRTCAPDIR(DWC3_GCTL_PRTCAP_HOST);
+ /*
+ * Allow ITP generated off of ref clk based counter instead
+ * of UTMI/ULPI clk based counter, when superspeed only is
+ * active so that UTMI/ULPI can be suspened.
+ */
+ reg |= DWC3_GCTL_SOFITPSYNC;
+ /*
+ * Set this bit so that device attempts three more times at SS,
+ * even if it failed previously to operate in SS mode.
+ */
+ reg |= DWC3_GCTL_U2RSTECN;
+ reg &= ~(DWC3_GCTL_PWRDNSCALEMASK);
+ reg |= DWC3_GCTL_PWRDNSCALE(2);
dwc3_writel(dwc->regs, DWC3_GCTL, reg);
}
}
@@ -126,6 +139,14 @@
reg = dwc3_readl(dwc->regs, DWC3_GCTL);
reg &= ~(DWC3_GCTL_PRTCAPDIR(DWC3_GCTL_PRTCAP_OTG));
reg |= DWC3_GCTL_PRTCAPDIR(DWC3_GCTL_PRTCAP_DEVICE);
+ /*
+ * Set this bit so that device attempts three more times at SS,
+ * even if it failed previously to operate in SS mode.
+ */
+ reg |= DWC3_GCTL_U2RSTECN;
+ reg &= ~(DWC3_GCTL_PWRDNSCALEMASK);
+ reg |= DWC3_GCTL_PWRDNSCALE(2);
+ reg &= ~(DWC3_GCTL_SOFITPSYNC);
dwc3_writel(dwc->regs, DWC3_GCTL, reg);
}
}
@@ -847,7 +868,8 @@
* OCFG[1] - HNPCap = 0
* OCFG[0] - SRPCap = 0
*/
- dwc3_writel(dotg->regs, DWC3_OCFG, 0x4);
+ if (ext_xceiv && !ext_xceiv->otg_capability)
+ dwc3_writel(dotg->regs, DWC3_OCFG, 0x4);
/*
* OCTL[6] - PeriMode = 1
@@ -859,7 +881,8 @@
* OCTL[0] - HstSetHNPEn = 0
*/
if (!once) {
- dwc3_writel(dotg->regs, DWC3_OCTL, 0x40);
+ if (ext_xceiv && !ext_xceiv->otg_capability)
+ dwc3_writel(dotg->regs, DWC3_OCTL, 0x40);
once++;
}