e1000e: disable K1 on PCH LOM when in PHY loopback mode
When performing the ethtool PHY loopback test on PCH-based LOMs (82577 and
82578), disable K1 (a MAC-PHY interconnect low power mode) otherwise
packets might get corrupted.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
diff --git a/drivers/net/e1000e/e1000.h b/drivers/net/e1000e/e1000.h
index 00989c5..a6c6803 100644
--- a/drivers/net/e1000e/e1000.h
+++ b/drivers/net/e1000e/e1000.h
@@ -485,6 +485,7 @@
extern void e1000e_igp3_phy_powerdown_workaround_ich8lan(struct e1000_hw *hw);
extern void e1000e_gig_downshift_workaround_ich8lan(struct e1000_hw *hw);
extern void e1000e_disable_gig_wol_ich8lan(struct e1000_hw *hw);
+extern s32 e1000_configure_k1_ich8lan(struct e1000_hw *hw, bool k1_enable);
extern s32 e1000e_check_for_copper_link(struct e1000_hw *hw);
extern s32 e1000e_check_for_fiber_link(struct e1000_hw *hw);
diff --git a/drivers/net/e1000e/ethtool.c b/drivers/net/e1000e/ethtool.c
index 67e06fd..fd79214 100644
--- a/drivers/net/e1000e/ethtool.c
+++ b/drivers/net/e1000e/ethtool.c
@@ -1260,6 +1260,10 @@
hw->mac.autoneg = 0;
+ /* Workaround: K1 must be disabled for stable 1Gbps operation */
+ if (hw->mac.type == e1000_pchlan)
+ e1000_configure_k1_ich8lan(hw, false);
+
if (hw->phy.type == e1000_phy_m88) {
/* Auto-MDI/MDIX Off */
e1e_wphy(hw, M88E1000_PHY_SPEC_CTRL, 0x0808);
diff --git a/drivers/net/e1000e/ich8lan.c b/drivers/net/e1000e/ich8lan.c
index 51ddb04..bd9002e 100644
--- a/drivers/net/e1000e/ich8lan.c
+++ b/drivers/net/e1000e/ich8lan.c
@@ -224,7 +224,6 @@
static s32 e1000_set_lplu_state_pchlan(struct e1000_hw *hw, bool active);
static void e1000_lan_init_done_ich8lan(struct e1000_hw *hw);
static s32 e1000_k1_gig_workaround_hv(struct e1000_hw *hw, bool link);
-static s32 e1000_configure_k1_ich8lan(struct e1000_hw *hw, bool k1_enable);
static inline u16 __er16flash(struct e1000_hw *hw, unsigned long reg)
{
@@ -1023,7 +1022,7 @@
*
* Success returns 0, Failure returns -E1000_ERR_PHY (-2)
**/
-static s32 e1000_configure_k1_ich8lan(struct e1000_hw *hw, bool k1_enable)
+s32 e1000_configure_k1_ich8lan(struct e1000_hw *hw, bool k1_enable)
{
s32 ret_val = 0;
u32 ctrl_reg = 0;