qlge: Add ethtool wake on LAN function.
Signed-off-by: Ron Mercer <ron.mercer@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
diff --git a/drivers/net/qlge/qlge_main.c b/drivers/net/qlge/qlge_main.c
index 34242fb..dd0ea02 100644
--- a/drivers/net/qlge/qlge_main.c
+++ b/drivers/net/qlge/qlge_main.c
@@ -3335,6 +3335,22 @@
* the same MAC address.
*/
ql_write32(qdev, RST_FO, RST_FO_RR_MASK | RST_FO_RR_RCV_FUNC_CQ);
+ /* Reroute all packets to our Interface.
+ * They may have been routed to MPI firmware
+ * due to WOL.
+ */
+ value = ql_read32(qdev, MGMT_RCV_CFG);
+ value &= ~MGMT_RCV_CFG_RM;
+ mask = 0xffff0000;
+
+ /* Sticky reg needs clearing due to WOL. */
+ ql_write32(qdev, MGMT_RCV_CFG, mask);
+ ql_write32(qdev, MGMT_RCV_CFG, mask | value);
+
+ /* Default WOL is enable on Mezz cards */
+ if (qdev->pdev->subsystem_device == 0x0068 ||
+ qdev->pdev->subsystem_device == 0x0180)
+ qdev->wol = WAKE_MAGIC;
/* Start up the rx queues. */
for (i = 0; i < qdev->rx_ring_count; i++) {
@@ -3449,6 +3465,55 @@
QPRINTK(qdev, PROBE, INFO, "MAC address %pM\n", ndev->dev_addr);
}
+int ql_wol(struct ql_adapter *qdev)
+{
+ int status = 0;
+ u32 wol = MB_WOL_DISABLE;
+
+ /* The CAM is still intact after a reset, but if we
+ * are doing WOL, then we may need to program the
+ * routing regs. We would also need to issue the mailbox
+ * commands to instruct the MPI what to do per the ethtool
+ * settings.
+ */
+
+ if (qdev->wol & (WAKE_ARP | WAKE_MAGICSECURE | WAKE_PHY | WAKE_UCAST |
+ WAKE_MCAST | WAKE_BCAST)) {
+ QPRINTK(qdev, IFDOWN, ERR,
+ "Unsupported WOL paramter. qdev->wol = 0x%x.\n",
+ qdev->wol);
+ return -EINVAL;
+ }
+
+ if (qdev->wol & WAKE_MAGIC) {
+ status = ql_mb_wol_set_magic(qdev, 1);
+ if (status) {
+ QPRINTK(qdev, IFDOWN, ERR,
+ "Failed to set magic packet on %s.\n",
+ qdev->ndev->name);
+ return status;
+ } else
+ QPRINTK(qdev, DRV, INFO,
+ "Enabled magic packet successfully on %s.\n",
+ qdev->ndev->name);
+
+ wol |= MB_WOL_MAGIC_PKT;
+ }
+
+ if (qdev->wol) {
+ /* Reroute all packets to Management Interface */
+ ql_write32(qdev, MGMT_RCV_CFG, (MGMT_RCV_CFG_RM |
+ (MGMT_RCV_CFG_RM << 16)));
+ wol |= MB_WOL_MODE_ON;
+ status = ql_mb_wol_mode(qdev, wol);
+ QPRINTK(qdev, DRV, ERR, "WOL %s (wol code 0x%x) on %s\n",
+ (status == 0) ? "Sucessfully set" : "Failed", wol,
+ qdev->ndev->name);
+ }
+
+ return status;
+}
+
static int ql_adapter_down(struct ql_adapter *qdev)
{
int i, status = 0;
@@ -4285,6 +4350,7 @@
return err;
}
+ ql_wol(qdev);
err = pci_save_state(pdev);
if (err)
return err;