Merge commit 'gcl/gcl-next'
diff --git a/Documentation/powerpc/booting-without-of.txt b/Documentation/powerpc/booting-without-of.txt
index ea1b70b..99514ce 100644
--- a/Documentation/powerpc/booting-without-of.txt
+++ b/Documentation/powerpc/booting-without-of.txt
@@ -59,6 +59,7 @@
p) Freescale Synchronous Serial Interface
q) USB EHCI controllers
r) MDIO on GPIOs
+ s) SPI busses
VII - Marvell Discovery mv64[345]6x System Controller chips
1) The /system-controller node
@@ -1883,6 +1884,62 @@
&qe_pio_c 6>;
};
+ s) SPI (Serial Peripheral Interface) busses
+
+ SPI busses can be described with a node for the SPI master device
+ and a set of child nodes for each SPI slave on the bus. For this
+ discussion, it is assumed that the system's SPI controller is in
+ SPI master mode. This binding does not describe SPI controllers
+ in slave mode.
+
+ The SPI master node requires the following properties:
+ - #address-cells - number of cells required to define a chip select
+ address on the SPI bus.
+ - #size-cells - should be zero.
+ - compatible - name of SPI bus controller following generic names
+ recommended practice.
+ No other properties are required in the SPI bus node. It is assumed
+ that a driver for an SPI bus device will understand that it is an SPI bus.
+ However, the binding does not attempt to define the specific method for
+ assigning chip select numbers. Since SPI chip select configuration is
+ flexible and non-standardized, it is left out of this binding with the
+ assumption that board specific platform code will be used to manage
+ chip selects. Individual drivers can define additional properties to
+ support describing the chip select layout.
+
+ SPI slave nodes must be children of the SPI master node and can
+ contain the following properties.
+ - reg - (required) chip select address of device.
+ - compatible - (required) name of SPI device following generic names
+ recommended practice
+ - spi-max-frequency - (required) Maximum SPI clocking speed of device in Hz
+ - spi-cpol - (optional) Empty property indicating device requires
+ inverse clock polarity (CPOL) mode
+ - spi-cpha - (optional) Empty property indicating device requires
+ shifted clock phase (CPHA) mode
+
+ SPI example for an MPC5200 SPI bus:
+ spi@f00 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ compatible = "fsl,mpc5200b-spi","fsl,mpc5200-spi";
+ reg = <0xf00 0x20>;
+ interrupts = <2 13 0 2 14 0>;
+ interrupt-parent = <&mpc5200_pic>;
+
+ ethernet-switch@0 {
+ compatible = "micrel,ks8995m";
+ spi-max-frequency = <1000000>;
+ reg = <0>;
+ };
+
+ codec@1 {
+ compatible = "ti,tlv320aic26";
+ spi-max-frequency = <100000>;
+ reg = <1>;
+ };
+ };
+
VII - Marvell Discovery mv64[345]6x System Controller chips
===========================================================
diff --git a/arch/powerpc/platforms/52xx/Kconfig b/arch/powerpc/platforms/52xx/Kconfig
index d664b1b..9a51675 100644
--- a/arch/powerpc/platforms/52xx/Kconfig
+++ b/arch/powerpc/platforms/52xx/Kconfig
@@ -1,7 +1,6 @@
config PPC_MPC52xx
bool "52xx-based boards"
depends on PPC_MULTIPLATFORM && PPC32
- select FSL_SOC
select PPC_CLOCK
select PPC_PCI_CHOICE
@@ -48,6 +47,7 @@
config PPC_MPC5200_GPIO
bool "MPC5200 GPIO support"
depends on PPC_MPC52xx
+ select GENERIC_GPIO
select HAVE_GPIO_LIB
help
Enable gpiolib support for mpc5200 based boards
diff --git a/drivers/of/of_i2c.c b/drivers/of/of_i2c.c
index 5c015d3..344e1b0 100644
--- a/drivers/of/of_i2c.c
+++ b/drivers/of/of_i2c.c
@@ -91,8 +91,6 @@
}
info.irq = irq_of_parse_and_map(node, 0);
- if (info.irq == NO_IRQ)
- info.irq = -1;
if (of_find_i2c_driver(node, &info) < 0) {
irq_dispose_mapping(info.irq);
diff --git a/include/asm-powerpc/mpc52xx_psc.h b/include/asm-powerpc/mpc52xx_psc.h
index 710c5d3..8917ed6 100644
--- a/include/asm-powerpc/mpc52xx_psc.h
+++ b/include/asm-powerpc/mpc52xx_psc.h
@@ -60,10 +60,12 @@
#define MPC52xx_PSC_RXTX_FIFO_ALARM 0x0002
#define MPC52xx_PSC_RXTX_FIFO_EMPTY 0x0001
-/* PSC interrupt mask bits */
+/* PSC interrupt status/mask bits */
#define MPC52xx_PSC_IMR_TXRDY 0x0100
#define MPC52xx_PSC_IMR_RXRDY 0x0200
#define MPC52xx_PSC_IMR_DB 0x0400
+#define MPC52xx_PSC_IMR_TXEMP 0x0800
+#define MPC52xx_PSC_IMR_ORERR 0x1000
#define MPC52xx_PSC_IMR_IPC 0x8000
/* PSC input port change bit */
@@ -92,6 +94,34 @@
#define MPC52xx_PSC_RFNUM_MASK 0x01ff
+#define MPC52xx_PSC_SICR_DTS1 (1 << 29)
+#define MPC52xx_PSC_SICR_SHDR (1 << 28)
+#define MPC52xx_PSC_SICR_SIM_MASK (0xf << 24)
+#define MPC52xx_PSC_SICR_SIM_UART (0x0 << 24)
+#define MPC52xx_PSC_SICR_SIM_UART_DCD (0x8 << 24)
+#define MPC52xx_PSC_SICR_SIM_CODEC_8 (0x1 << 24)
+#define MPC52xx_PSC_SICR_SIM_CODEC_16 (0x2 << 24)
+#define MPC52xx_PSC_SICR_SIM_AC97 (0x3 << 24)
+#define MPC52xx_PSC_SICR_SIM_SIR (0x8 << 24)
+#define MPC52xx_PSC_SICR_SIM_SIR_DCD (0xc << 24)
+#define MPC52xx_PSC_SICR_SIM_MIR (0x5 << 24)
+#define MPC52xx_PSC_SICR_SIM_FIR (0x6 << 24)
+#define MPC52xx_PSC_SICR_SIM_CODEC_24 (0x7 << 24)
+#define MPC52xx_PSC_SICR_SIM_CODEC_32 (0xf << 24)
+#define MPC52xx_PSC_SICR_GENCLK (1 << 23)
+#define MPC52xx_PSC_SICR_I2S (1 << 22)
+#define MPC52xx_PSC_SICR_CLKPOL (1 << 21)
+#define MPC52xx_PSC_SICR_SYNCPOL (1 << 20)
+#define MPC52xx_PSC_SICR_CELLSLAVE (1 << 19)
+#define MPC52xx_PSC_SICR_CELL2XCLK (1 << 18)
+#define MPC52xx_PSC_SICR_ESAI (1 << 17)
+#define MPC52xx_PSC_SICR_ENAC97 (1 << 16)
+#define MPC52xx_PSC_SICR_SPI (1 << 15)
+#define MPC52xx_PSC_SICR_MSTR (1 << 14)
+#define MPC52xx_PSC_SICR_CPOL (1 << 13)
+#define MPC52xx_PSC_SICR_CPHA (1 << 12)
+#define MPC52xx_PSC_SICR_USEEOF (1 << 11)
+#define MPC52xx_PSC_SICR_DISABLEEOF (1 << 10)
/* Structure of the hardware registers */
struct mpc52xx_psc {
@@ -132,8 +162,12 @@
u8 reserved5[3];
u8 ctlr; /* PSC + 0x1c */
u8 reserved6[3];
- u16 ccr; /* PSC + 0x20 */
- u8 reserved7[14];
+ /* BitClkDiv field of CCR is byte swapped in
+ * the hardware for mpc5200/b compatibility */
+ u32 ccr; /* PSC + 0x20 */
+ u32 ac97_slots; /* PSC + 0x24 */
+ u32 ac97_cmd; /* PSC + 0x28 */
+ u32 ac97_data; /* PSC + 0x2c */
u8 ivr; /* PSC + 0x30 */
u8 reserved8[3];
u8 ip; /* PSC + 0x34 */