fix typos "wich" -> "which"
Signed-off-by: Uwe Zeisberger <zeisberg@informatik.uni-freiburg.de>
Signed-off-by: Adrian Bunk <bunk@stusta.de>
diff --git a/drivers/acpi/Kconfig b/drivers/acpi/Kconfig
index 82710ae..5cb9630 100644
--- a/drivers/acpi/Kconfig
+++ b/drivers/acpi/Kconfig
@@ -256,7 +256,8 @@
depends on ACPI_CUSTOM_DSDT
default ""
help
- Enter the full path name to the file wich includes the AmlCode declaration.
+ Enter the full path name to the file which includes the AmlCode
+ declaration.
config ACPI_BLACKLIST_YEAR
int "Disable ACPI for systems before Jan 1st this year" if X86_32
diff --git a/drivers/isdn/i4l/isdn_x25iface.c b/drivers/isdn/i4l/isdn_x25iface.c
index edf14a2..743ac40 100644
--- a/drivers/isdn/i4l/isdn_x25iface.c
+++ b/drivers/isdn/i4l/isdn_x25iface.c
@@ -7,7 +7,7 @@
*
* stuff needed to support the Linux X.25 PLP code on top of devices that
* can provide a lab_b service using the concap_proto mechanism.
- * This module supports a network interface wich provides lapb_sematics
+ * This module supports a network interface which provides lapb_sematics
* -- as defined in Documentation/networking/x25-iface.txt -- to
* the upper layer and assumes that the lower layer provides a reliable
* data link service by means of the concap_device_ops callbacks.
diff --git a/drivers/serial/mpc52xx_uart.c b/drivers/serial/mpc52xx_uart.c
index 928e6cf..6459edc 100644
--- a/drivers/serial/mpc52xx_uart.c
+++ b/drivers/serial/mpc52xx_uart.c
@@ -40,7 +40,7 @@
* and so on). So the PSC1 is mapped to /dev/ttyPSC0, PSC2 to /dev/ttyPSC1 and
* so on. But be warned, it's an ABSOLUTE REQUIREMENT ! This is needed mainly
* fpr the console code : without this 1:1 mapping, at early boot time, when we
- * are parsing the kernel args console=ttyPSC?, we wouldn't know wich PSC it
+ * are parsing the kernel args console=ttyPSC?, we wouldn't know which PSC it
* will be mapped to.
*/
diff --git a/drivers/usb/serial/option.c b/drivers/usb/serial/option.c
index a8455c9..495db57 100644
--- a/drivers/usb/serial/option.c
+++ b/drivers/usb/serial/option.c
@@ -102,7 +102,7 @@
.no_dynamic_id = 1,
};
-/* The card has three separate interfaces, wich the serial driver
+/* The card has three separate interfaces, which the serial driver
* recognizes separately, thus num_port=1.
*/
static struct usb_serial_driver option_3port_device = {
diff --git a/drivers/video/sstfb.c b/drivers/video/sstfb.c
index 99921df..8c1a8b5 100644
--- a/drivers/video/sstfb.c
+++ b/drivers/video/sstfb.c
@@ -32,7 +32,7 @@
-TODO: at one time or another test that the mode is acceptable by the monitor
-ASK: Can I choose different ordering for the color bitfields (rgba argb ...)
- wich one should i use ? is there any preferred one ? It seems ARGB is
+ which one should i use ? is there any preferred one ? It seems ARGB is
the one ...
-TODO: in set_var check the validity of timings (hsync vsync)...
-TODO: check and recheck the use of sst_wait_idle : we don't flush the fifo via
diff --git a/drivers/w1/masters/matrox_w1.c b/drivers/w1/masters/matrox_w1.c
index 591809c..2788b8c 100644
--- a/drivers/w1/masters/matrox_w1.c
+++ b/drivers/w1/masters/matrox_w1.c
@@ -98,7 +98,7 @@
*
* Using tristate pins, since i can't find any open-drain pin in whole motherboard.
* Unfortunately we can't connect to Intel's 82801xx IO controller
- * since we don't know motherboard schema, wich has pretty unused(may be not) GPIO.
+ * since we don't know motherboard schema, which has pretty unused(may be not) GPIO.
*
* I've heard that PIIX also has open drain pin.
*