[SCSI] qla2xxx: Add ISP25XX support.
Large code-reuse from ISP24xx, consolidate RISC memory
extraction routines during firmware-dump.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
diff --git a/drivers/scsi/qla2xxx/qla_fw.h b/drivers/scsi/qla2xxx/qla_fw.h
index 63a11fe..99fe496 100644
--- a/drivers/scsi/qla2xxx/qla_fw.h
+++ b/drivers/scsi/qla2xxx/qla_fw.h
@@ -8,14 +8,17 @@
#define __QLA_FW_H
#define MBS_CHECKSUM_ERROR 0x4010
+#define MBS_INVALID_PRODUCT_KEY 0x4020
/*
* Firmware Options.
*/
#define FO1_ENABLE_PUREX BIT_10
#define FO1_DISABLE_LED_CTRL BIT_6
+#define FO1_ENABLE_8016 BIT_0
#define FO2_ENABLE_SEL_CLASS2 BIT_5
#define FO3_NO_ABTS_ON_LINKDOWN BIT_14
+#define FO3_HOLD_STS_IOCB BIT_12
/*
* Port Database structure definition for ISP 24xx.
@@ -341,7 +344,9 @@
* BIT 10 = Reserved
* BIT 11 = Enable FC-SP Security
* BIT 12 = FC Tape Enable
- * BIT 13-31 = Reserved
+ * BIT 13 = Reserved
+ * BIT 14 = Enable Target PRLI Control
+ * BIT 15-31 = Reserved
*/
uint32_t firmware_options_2;
@@ -363,7 +368,8 @@
* BIT 13 = Data Rate bit 0
* BIT 14 = Data Rate bit 1
* BIT 15 = Data Rate bit 2
- * BIT 16-31 = Reserved
+ * BIT 16 = Enable 75 ohm Termination Select
+ * BIT 17-31 = Reserved
*/
uint32_t firmware_options_3;
@@ -435,6 +441,7 @@
#define TMF_LUN_RESET BIT_12
#define TMF_CLEAR_TASK_SET BIT_10
#define TMF_ABORT_TASK_SET BIT_9
+#define TMF_DSD_LIST_ENABLE BIT_2
#define TMF_READ_DATA BIT_1
#define TMF_WRITE_DATA BIT_0
@@ -589,7 +596,7 @@
#define EST_SOFI3 (1 << 4)
#define EST_SOFI2 (3 << 4)
- uint32_t rx_xchg_address[2]; /* Receive exchange address. */
+ uint32_t rx_xchg_address; /* Receive exchange address. */
uint16_t rx_dsd_count;
uint8_t opcode;
@@ -650,6 +657,7 @@
uint16_t control_flags; /* Control flags. */
/* Modifiers. */
+#define LCF_INCLUDE_SNS BIT_10 /* Include SNS (FFFFFC) during LOGO. */
#define LCF_FCP2_OVERRIDE BIT_9 /* Set/Reset word 3 of PRLI. */
#define LCF_CLASS_2 BIT_8 /* Enable class 2 during PLOGI. */
#define LCF_FREE_NPORT BIT_7 /* Release NPORT handle after LOGO. */
@@ -779,6 +787,15 @@
#define FA_RISC_CODE_ADDR 0x20000
#define FA_RISC_CODE_SEGMENTS 2
+#define FA_FW_AREA_ADDR 0x40000
+#define FA_VPD_NVRAM_ADDR 0x48000
+#define FA_FEATURE_ADDR 0x4C000
+#define FA_FLASH_DESCR_ADDR 0x50000
+#define FA_HW_EVENT_ADDR 0x54000
+#define FA_BOOT_LOG_ADDR 0x58000
+#define FA_FW_DUMP0_ADDR 0x60000
+#define FA_FW_DUMP1_ADDR 0x70000
+
uint32_t flash_data; /* Flash/NVRAM BIOS data. */
uint32_t ctrl_status; /* Control/Status. */
@@ -859,10 +876,13 @@
#define HCCRX_CLR_RISC_INT 0xA0000000
uint32_t gpiod; /* GPIO Data register. */
+
/* LED update mask. */
#define GPDX_LED_UPDATE_MASK (BIT_20|BIT_19|BIT_18)
/* Data update mask. */
#define GPDX_DATA_UPDATE_MASK (BIT_17|BIT_16)
+ /* Data update mask. */
+#define GPDX_DATA_UPDATE_2_MASK (BIT_28|BIT_27|BIT_26|BIT_17|BIT_16)
/* LED control mask. */
#define GPDX_LED_COLOR_MASK (BIT_4|BIT_3|BIT_2)
/* LED bit values. Color names as
@@ -877,6 +897,8 @@
uint32_t gpioe; /* GPIO Enable register. */
/* Enable update mask. */
#define GPEX_ENABLE_UPDATE_MASK (BIT_17|BIT_16)
+ /* Enable update mask. */
+#define GPEX_ENABLE_UPDATE_2_MASK (BIT_28|BIT_27|BIT_26|BIT_17|BIT_16)
/* Enable. */
#define GPEX_ENABLE (BIT_1|BIT_0)
@@ -916,6 +938,14 @@
uint16_t mailbox29;
uint16_t mailbox30;
uint16_t mailbox31;
+
+ uint32_t iobase_window;
+ uint32_t unused_4[8]; /* Gap. */
+ uint32_t iobase_q;
+ uint32_t unused_5[2]; /* Gap. */
+ uint32_t iobase_select;
+ uint32_t unused_6[2]; /* Gap. */
+ uint32_t iobase_sdata;
};
/* MID Support ***************************************************************/