ARM: OMAP: omap camera builds again; Mistral init and mux
Support the camera connector on the OSK Mistral add-on board:
- define muxing for both camera controllers
- mux both of them for Mistral
- teach ov9640 glue about mistral powerup/powerdown
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Tony Lindgren <tony@atomide.com>
diff --git a/arch/arm/mach-omap1/board-osk.c b/arch/arm/mach-omap1/board-osk.c
index e713029..2bfa088 100644
--- a/arch/arm/mach-omap1/board-osk.c
+++ b/arch/arm/mach-omap1/board-osk.c
@@ -342,6 +342,38 @@
* can't talk to the ads or even the i2c eeprom.
*/
+ /* parallel camera interface */
+ omap_cfg_reg(J15_1610_CAM_LCLK);
+ omap_cfg_reg(J18_1610_CAM_D7);
+ omap_cfg_reg(J19_1610_CAM_D6);
+ omap_cfg_reg(J14_1610_CAM_D5);
+ omap_cfg_reg(K18_1610_CAM_D4);
+ omap_cfg_reg(K19_1610_CAM_D3);
+ omap_cfg_reg(K15_1610_CAM_D2);
+ omap_cfg_reg(K14_1610_CAM_D1);
+ omap_cfg_reg(L19_1610_CAM_D0);
+ omap_cfg_reg(L18_1610_CAM_VS);
+ omap_cfg_reg(L15_1610_CAM_HS);
+ omap_cfg_reg(M19_1610_CAM_RSTZ);
+ omap_cfg_reg(Y15_1610_CAM_OUTCLK);
+
+ /* serial camera interface */
+ omap_cfg_reg(H19_1610_CAM_EXCLK);
+ omap_cfg_reg(W13_1610_CCP_CLKM);
+ omap_cfg_reg(Y12_1610_CCP_CLKP);
+ /* CCP_DATAM CONFLICTS WITH UART1.TX (and serial console) */
+ // omap_cfg_reg(Y14_1610_CCP_DATAM);
+ omap_cfg_reg(W14_1610_CCP_DATAP);
+
+ /* CAM_PWDN */
+ if (omap_request_gpio(11) == 0) {
+ omap_cfg_reg(N20_1610_GPIO11);
+ omap_set_gpio_direction(11, 0 /* out */);
+ omap_set_gpio_dataout(11, 0 /* off */);
+ } else
+ pr_debug("OSK+Mistral: CAM_PWDN is awol\n");
+
+
// omap_cfg_reg(P19_1610_GPIO6); // BUSY
omap_cfg_reg(P20_1610_GPIO4); // PENIRQ
set_irq_type(OMAP_GPIO_IRQ(4), IRQT_FALLING);
diff --git a/arch/arm/mach-omap1/mux.c b/arch/arm/mach-omap1/mux.c
index 5432335..52c70e5 100644
--- a/arch/arm/mach-omap1/mux.c
+++ b/arch/arm/mach-omap1/mux.c
@@ -283,6 +283,30 @@
MUX_CFG("V10_1610_CF_IREQ", A, 24, 3, 2, 14, 0, 2, 0, 1)
MUX_CFG("W10_1610_CF_RESET", A, 18, 3, 2, 12, 1, 2, 1, 1)
MUX_CFG("W11_1610_CF_CD1", 10, 15, 3, 3, 8, 1, 3, 1, 1)
+
+/* parallel camera */
+MUX_CFG("J15_1610_CAM_LCLK", 4, 24, 0, 0, 18, 1, 0, 0, 0)
+MUX_CFG("J18_1610_CAM_D7", 4, 27, 0, 0, 19, 1, 0, 0, 0)
+MUX_CFG("J19_1610_CAM_D6", 5, 0, 0, 0, 20, 1, 0, 0, 0)
+MUX_CFG("J14_1610_CAM_D5", 5, 3, 0, 0, 21, 1, 0, 0, 0)
+MUX_CFG("K18_1610_CAM_D4", 5, 6, 0, 0, 22, 1, 0, 0, 0)
+MUX_CFG("K19_1610_CAM_D3", 5, 9, 0, 0, 23, 1, 0, 0, 0)
+MUX_CFG("K15_1610_CAM_D2", 5, 12, 0, 0, 24, 1, 0, 0, 0)
+MUX_CFG("K14_1610_CAM_D1", 5, 15, 0, 0, 25, 1, 0, 0, 0)
+MUX_CFG("L19_1610_CAM_D0", 5, 18, 0, 0, 26, 1, 0, 0, 0)
+MUX_CFG("L18_1610_CAM_VS", 5, 21, 0, 0, 27, 1, 0, 0, 0)
+MUX_CFG("L15_1610_CAM_HS", 5, 24, 0, 0, 28, 1, 0, 0, 0)
+MUX_CFG("M19_1610_CAM_RSTZ", 5, 27, 0, 0, 29, 0, 0, 0, 0)
+MUX_CFG("Y15_1610_CAM_OUTCLK", A, 0, 6, 2, 6, 0, 2, 0, 0)
+
+/* serial camera */
+MUX_CFG("H19_1610_CAM_EXCLK", 4, 21, 0, 0, 17, 0, 0, 0, 0)
+ /* REVISIT 5912 spec sez CCP_* can't pullup or pulldown ... ? */
+MUX_CFG("Y12_1610_CCP_CLKP", 8, 18, 6, 1, 24, 1, 1, 0, 0)
+MUX_CFG("W13_1610_CCP_CLKM", 9, 0, 6, 1, 28, 1, 1, 0, 0)
+MUX_CFG("W14_1610_CCP_DATAP", 9, 24, 6, 2, 4, 1, 2, 0, 0)
+MUX_CFG("Y14_1610_CCP_DATAM", 9, 21, 6, 2, 3, 1, 2, 0, 0)
+
};
#endif /* CONFIG_ARCH_OMAP15XX || CONFIG_ARCH_OMAP16XX */
diff --git a/include/asm-arm/arch-omap/mux.h b/include/asm-arm/arch-omap/mux.h
index f1ec2ed..b8fff50 100644
--- a/include/asm-arm/arch-omap/mux.h
+++ b/include/asm-arm/arch-omap/mux.h
@@ -406,6 +406,29 @@
V10_1610_CF_IREQ,
W10_1610_CF_RESET,
W11_1610_CF_CD1,
+
+ /* parallel camera */
+ J15_1610_CAM_LCLK,
+ J18_1610_CAM_D7,
+ J19_1610_CAM_D6,
+ J14_1610_CAM_D5,
+ K18_1610_CAM_D4,
+ K19_1610_CAM_D3,
+ K15_1610_CAM_D2,
+ K14_1610_CAM_D1,
+ L19_1610_CAM_D0,
+ L18_1610_CAM_VS,
+ L15_1610_CAM_HS,
+ M19_1610_CAM_RSTZ,
+ Y15_1610_CAM_OUTCLK,
+
+ /* serial camera */
+ H19_1610_CAM_EXCLK,
+ Y12_1610_CCP_CLKP,
+ W13_1610_CCP_CLKM,
+ W14_1610_CCP_DATAP,
+ Y14_1610_CCP_DATAM,
+
};
enum omap24xx_index {