| /* |
| * This file is part of wl1271 |
| * |
| * Copyright (C) 2009 Nokia Corporation |
| * |
| * Contact: Luciano Coelho <luciano.coelho@nokia.com> |
| * |
| * This program is free software; you can redistribute it and/or |
| * modify it under the terms of the GNU General Public License |
| * version 2 as published by the Free Software Foundation. |
| * |
| * This program is distributed in the hope that it will be useful, but |
| * WITHOUT ANY WARRANTY; without even the implied warranty of |
| * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the GNU |
| * General Public License for more details. |
| * |
| * You should have received a copy of the GNU General Public License |
| * along with this program; if not, write to the Free Software |
| * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA |
| * 02110-1301 USA |
| * |
| */ |
| |
| #ifndef __WL1271_CONF_H__ |
| #define __WL1271_CONF_H__ |
| |
| enum { |
| CONF_HW_BIT_RATE_1MBPS = BIT(0), |
| CONF_HW_BIT_RATE_2MBPS = BIT(1), |
| CONF_HW_BIT_RATE_5_5MBPS = BIT(2), |
| CONF_HW_BIT_RATE_6MBPS = BIT(3), |
| CONF_HW_BIT_RATE_9MBPS = BIT(4), |
| CONF_HW_BIT_RATE_11MBPS = BIT(5), |
| CONF_HW_BIT_RATE_12MBPS = BIT(6), |
| CONF_HW_BIT_RATE_18MBPS = BIT(7), |
| CONF_HW_BIT_RATE_22MBPS = BIT(8), |
| CONF_HW_BIT_RATE_24MBPS = BIT(9), |
| CONF_HW_BIT_RATE_36MBPS = BIT(10), |
| CONF_HW_BIT_RATE_48MBPS = BIT(11), |
| CONF_HW_BIT_RATE_54MBPS = BIT(12), |
| CONF_HW_BIT_RATE_MCS_0 = BIT(13), |
| CONF_HW_BIT_RATE_MCS_1 = BIT(14), |
| CONF_HW_BIT_RATE_MCS_2 = BIT(15), |
| CONF_HW_BIT_RATE_MCS_3 = BIT(16), |
| CONF_HW_BIT_RATE_MCS_4 = BIT(17), |
| CONF_HW_BIT_RATE_MCS_5 = BIT(18), |
| CONF_HW_BIT_RATE_MCS_6 = BIT(19), |
| CONF_HW_BIT_RATE_MCS_7 = BIT(20) |
| }; |
| |
| enum { |
| CONF_HW_RATE_INDEX_1MBPS = 0, |
| CONF_HW_RATE_INDEX_2MBPS = 1, |
| CONF_HW_RATE_INDEX_5_5MBPS = 2, |
| CONF_HW_RATE_INDEX_6MBPS = 3, |
| CONF_HW_RATE_INDEX_9MBPS = 4, |
| CONF_HW_RATE_INDEX_11MBPS = 5, |
| CONF_HW_RATE_INDEX_12MBPS = 6, |
| CONF_HW_RATE_INDEX_18MBPS = 7, |
| CONF_HW_RATE_INDEX_22MBPS = 8, |
| CONF_HW_RATE_INDEX_24MBPS = 9, |
| CONF_HW_RATE_INDEX_36MBPS = 10, |
| CONF_HW_RATE_INDEX_48MBPS = 11, |
| CONF_HW_RATE_INDEX_54MBPS = 12, |
| CONF_HW_RATE_INDEX_MAX = CONF_HW_RATE_INDEX_54MBPS, |
| }; |
| |
| struct conf_sg_settings { |
| /* |
| * Defines the PER threshold in PPM of the BT voice of which reaching |
| * this value will trigger raising the priority of the BT voice by |
| * the BT IP until next NFS sample interval time as defined in |
| * nfs_sample_interval. |
| * |
| * Unit: PER value in PPM (parts per million) |
| * #Error_packets / #Total_packets |
| |
| * Range: u32 |
| */ |
| u32 per_threshold; |
| |
| /* |
| * This value is an absolute time in micro-seconds to limit the |
| * maximum scan duration compensation while in SG |
| */ |
| u32 max_scan_compensation_time; |
| |
| /* Defines the PER threshold of the BT voice of which reaching this |
| * value will trigger raising the priority of the BT voice until next |
| * NFS sample interval time as defined in sample_interval. |
| * |
| * Unit: msec |
| * Range: 1-65000 |
| */ |
| u16 nfs_sample_interval; |
| |
| /* |
| * Defines the load ratio for the BT. |
| * The WLAN ratio is: 100 - load_ratio |
| * |
| * Unit: Percent |
| * Range: 0-100 |
| */ |
| u8 load_ratio; |
| |
| /* |
| * true - Co-ex is allowed to enter/exit P.S automatically and |
| * transparently to the host |
| * |
| * false - Co-ex is disallowed to enter/exit P.S and will trigger an |
| * event to the host to notify for the need to enter/exit P.S |
| * due to BT change state |
| * |
| */ |
| u8 auto_ps_mode; |
| |
| /* |
| * This parameter defines the compensation percentage of num of probe |
| * requests in case scan is initiated during BT voice/BT ACL |
| * guaranteed link. |
| * |
| * Unit: Percent |
| * Range: 0-255 (0 - No compensation) |
| */ |
| u8 probe_req_compensation; |
| |
| /* |
| * This parameter defines the compensation percentage of scan window |
| * size in case scan is initiated during BT voice/BT ACL Guaranteed |
| * link. |
| * |
| * Unit: Percent |
| * Range: 0-255 (0 - No compensation) |
| */ |
| u8 scan_window_compensation; |
| |
| /* |
| * Defines the antenna configuration. |
| * |
| * Range: 0 - Single Antenna; 1 - Dual Antenna |
| */ |
| u8 antenna_config; |
| |
| /* |
| * The percent out of the Max consecutive beacon miss roaming trigger |
| * which is the threshold for raising the priority of beacon |
| * reception. |
| * |
| * Range: 1-100 |
| * N = MaxConsecutiveBeaconMiss |
| * P = coexMaxConsecutiveBeaconMissPrecent |
| * Threshold = MIN( N-1, round(N * P / 100)) |
| */ |
| u8 beacon_miss_threshold; |
| |
| /* |
| * The RX rate threshold below which rate adaptation is assumed to be |
| * occurring at the AP which will raise priority for ACTIVE_RX and RX |
| * SP. |
| * |
| * Range: HW_BIT_RATE_* |
| */ |
| u32 rate_adaptation_threshold; |
| |
| /* |
| * The SNR above which the RX rate threshold indicating AP rate |
| * adaptation is valid |
| * |
| * Range: -128 - 127 |
| */ |
| s8 rate_adaptation_snr; |
| }; |
| |
| enum conf_rx_queue_type { |
| CONF_RX_QUEUE_TYPE_LOW_PRIORITY, /* All except the high priority */ |
| CONF_RX_QUEUE_TYPE_HIGH_PRIORITY, /* Management and voice packets */ |
| }; |
| |
| struct conf_rx_settings { |
| /* |
| * The maximum amount of time, in TU, before the |
| * firmware discards the MSDU. |
| * |
| * Range: 0 - 0xFFFFFFFF |
| */ |
| u32 rx_msdu_life_time; |
| |
| /* |
| * Packet detection threshold in the PHY. |
| * |
| * FIXME: details unknown. |
| */ |
| u32 packet_detection_threshold; |
| |
| /* |
| * The longest time the STA will wait to receive traffic from the AP |
| * after a PS-poll has been transmitted. |
| * |
| * Range: 0 - 200000 |
| */ |
| u16 ps_poll_timeout; |
| /* |
| * The longest time the STA will wait to receive traffic from the AP |
| * after a frame has been sent from an UPSD enabled queue. |
| * |
| * Range: 0 - 200000 |
| */ |
| u16 upsd_timeout; |
| |
| /* |
| * The number of octets in an MPDU, below which an RTS/CTS |
| * handshake is not performed. |
| * |
| * Range: 0 - 4096 |
| */ |
| u16 rts_threshold; |
| |
| /* |
| * The RX Clear Channel Assessment threshold in the PHY |
| * (the energy threshold). |
| * |
| * Range: ENABLE_ENERGY_D == 0x140A |
| * DISABLE_ENERGY_D == 0xFFEF |
| */ |
| u16 rx_cca_threshold; |
| |
| /* |
| * Occupied Rx mem-blocks number which requires interrupting the host |
| * (0 = no buffering, 0xffff = disabled). |
| * |
| * Range: u16 |
| */ |
| u16 irq_blk_threshold; |
| |
| /* |
| * Rx packets number which requires interrupting the host |
| * (0 = no buffering). |
| * |
| * Range: u16 |
| */ |
| u16 irq_pkt_threshold; |
| |
| /* |
| * Max time in msec the FW may delay RX-Complete interrupt. |
| * |
| * Range: 1 - 100 |
| */ |
| u16 irq_timeout; |
| |
| /* |
| * The RX queue type. |
| * |
| * Range: RX_QUEUE_TYPE_RX_LOW_PRIORITY, RX_QUEUE_TYPE_RX_HIGH_PRIORITY, |
| */ |
| u8 queue_type; |
| }; |
| |
| #define CONF_TX_MAX_RATE_CLASSES 8 |
| |
| #define CONF_TX_RATE_MASK_UNSPECIFIED 0 |
| #define CONF_TX_RATE_MASK_ALL 0x1eff |
| #define CONF_TX_RATE_RETRY_LIMIT 10 |
| |
| struct conf_tx_rate_class { |
| |
| /* |
| * The rates enabled for this rate class. |
| * |
| * Range: CONF_HW_BIT_RATE_* bit mask |
| */ |
| u32 enabled_rates; |
| |
| /* |
| * The dot11 short retry limit used for TX retries. |
| * |
| * Range: u8 |
| */ |
| u8 short_retry_limit; |
| |
| /* |
| * The dot11 long retry limit used for TX retries. |
| * |
| * Range: u8 |
| */ |
| u8 long_retry_limit; |
| |
| /* |
| * Flags controlling the attributes of TX transmission. |
| * |
| * Range: bit 0: Truncate - when set, FW attempts to send a frame stop |
| * when the total valid per-rate attempts have |
| * been exhausted; otherwise transmissions |
| * will continue at the lowest available rate |
| * until the appropriate one of the |
| * short_retry_limit, long_retry_limit, |
| * dot11_max_transmit_msdu_life_time, or |
| * max_tx_life_time, is exhausted. |
| * 1: Preamble Override - indicates if the preamble type |
| * should be used in TX. |
| * 2: Preamble Type - the type of the preamble to be used by |
| * the policy (0 - long preamble, 1 - short preamble. |
| */ |
| u8 aflags; |
| }; |
| |
| #define CONF_TX_MAX_AC_COUNT 4 |
| |
| /* Slot number setting to start transmission at PIFS interval */ |
| #define CONF_TX_AIFS_PIFS 1 |
| /* Slot number setting to start transmission at DIFS interval normal |
| * DCF access */ |
| #define CONF_TX_AIFS_DIFS 2 |
| |
| |
| enum conf_tx_ac { |
| CONF_TX_AC_BE = 0, /* best effort / legacy */ |
| CONF_TX_AC_BK = 1, /* background */ |
| CONF_TX_AC_VI = 2, /* video */ |
| CONF_TX_AC_VO = 3, /* voice */ |
| CONF_TX_AC_CTS2SELF = 4, /* fictious AC, follows AC_VO */ |
| CONF_TX_AC_ANY_TID = 0x1f |
| }; |
| |
| struct conf_tx_ac_category { |
| /* |
| * The AC class identifier. |
| * |
| * Range: enum conf_tx_ac |
| */ |
| u8 ac; |
| |
| /* |
| * The contention window minimum size (in slots) for the access |
| * class. |
| * |
| * Range: u8 |
| */ |
| u8 cw_min; |
| |
| /* |
| * The contention window maximum size (in slots) for the access |
| * class. |
| * |
| * Range: u8 |
| */ |
| u16 cw_max; |
| |
| /* |
| * The AIF value (in slots) for the access class. |
| * |
| * Range: u8 |
| */ |
| u8 aifsn; |
| |
| /* |
| * The TX Op Limit (in microseconds) for the access class. |
| * |
| * Range: u16 |
| */ |
| u16 tx_op_limit; |
| }; |
| |
| #define CONF_TX_MAX_TID_COUNT 7 |
| |
| enum { |
| CONF_CHANNEL_TYPE_DCF = 0, /* DC/LEGACY*/ |
| CONF_CHANNEL_TYPE_EDCF = 1, /* EDCA*/ |
| CONF_CHANNEL_TYPE_HCCA = 2, /* HCCA*/ |
| }; |
| |
| enum { |
| CONF_PS_SCHEME_LEGACY = 0, |
| CONF_PS_SCHEME_UPSD_TRIGGER = 1, |
| CONF_PS_SCHEME_LEGACY_PSPOLL = 2, |
| CONF_PS_SCHEME_SAPSD = 3, |
| }; |
| |
| enum { |
| CONF_ACK_POLICY_LEGACY = 0, |
| CONF_ACK_POLICY_NO_ACK = 1, |
| CONF_ACK_POLICY_BLOCK = 2, |
| }; |
| |
| |
| struct conf_tx_tid { |
| u8 queue_id; |
| u8 channel_type; |
| u8 tsid; |
| u8 ps_scheme; |
| u8 ack_policy; |
| u32 apsd_conf[2]; |
| }; |
| |
| struct conf_tx_settings { |
| /* |
| * The TX ED value for TELEC Enable/Disable. |
| * |
| * Range: 0, 1 |
| */ |
| u8 tx_energy_detection; |
| |
| /* |
| * Configuration for rate classes for TX (currently only one |
| * rate class supported.) |
| */ |
| struct conf_tx_rate_class rc_conf; |
| |
| /* |
| * Configuration for access categories for TX rate control. |
| */ |
| u8 ac_conf_count; |
| struct conf_tx_ac_category ac_conf[CONF_TX_MAX_AC_COUNT]; |
| |
| /* |
| * Configuration for TID parameters. |
| */ |
| u8 tid_conf_count; |
| struct conf_tx_tid tid_conf[CONF_TX_MAX_TID_COUNT]; |
| |
| /* |
| * The TX fragmentation threshold. |
| * |
| * Range: u16 |
| */ |
| u16 frag_threshold; |
| |
| /* |
| * Max time in msec the FW may delay frame TX-Complete interrupt. |
| * |
| * Range: u16 |
| */ |
| u16 tx_compl_timeout; |
| |
| /* |
| * Completed TX packet count which requires to issue the TX-Complete |
| * interrupt. |
| * |
| * Range: u16 |
| */ |
| u16 tx_compl_threshold; |
| |
| }; |
| |
| enum { |
| CONF_WAKE_UP_EVENT_BEACON = 0x01, /* Wake on every Beacon*/ |
| CONF_WAKE_UP_EVENT_DTIM = 0x02, /* Wake on every DTIM*/ |
| CONF_WAKE_UP_EVENT_N_DTIM = 0x04, /* Wake every Nth DTIM */ |
| CONF_WAKE_UP_EVENT_N_BEACONS = 0x08, /* Wake every Nth beacon */ |
| CONF_WAKE_UP_EVENT_BITS_MASK = 0x0F |
| }; |
| |
| #define CONF_MAX_BCN_FILT_IE_COUNT 32 |
| |
| #define CONF_BCN_RULE_PASS_ON_CHANGE BIT(0) |
| #define CONF_BCN_RULE_PASS_ON_APPEARANCE BIT(1) |
| |
| #define CONF_BCN_IE_OUI_LEN 3 |
| #define CONF_BCN_IE_VER_LEN 2 |
| |
| struct conf_bcn_filt_rule { |
| /* |
| * IE number to which to associate a rule. |
| * |
| * Range: u8 |
| */ |
| u8 ie; |
| |
| /* |
| * Rule to associate with the specific ie. |
| * |
| * Range: CONF_BCN_RULE_PASS_ON_* |
| */ |
| u8 rule; |
| |
| /* |
| * OUI for the vendor specifie IE (221) |
| */ |
| u8 oui[CONF_BCN_IE_OUI_LEN]; |
| |
| /* |
| * Type for the vendor specifie IE (221) |
| */ |
| u8 type; |
| |
| /* |
| * Version for the vendor specifie IE (221) |
| */ |
| u8 version[CONF_BCN_IE_VER_LEN]; |
| }; |
| |
| #define CONF_MAX_RSSI_SNR_TRIGGERS 8 |
| |
| enum { |
| CONF_TRIG_METRIC_RSSI_BEACON = 0, |
| CONF_TRIG_METRIC_RSSI_DATA, |
| CONF_TRIG_METRIC_SNR_BEACON, |
| CONF_TRIG_METRIC_SNR_DATA |
| }; |
| |
| enum { |
| CONF_TRIG_EVENT_TYPE_LEVEL = 0, |
| CONF_TRIG_EVENT_TYPE_EDGE |
| }; |
| |
| enum { |
| CONF_TRIG_EVENT_DIR_LOW = 0, |
| CONF_TRIG_EVENT_DIR_HIGH, |
| CONF_TRIG_EVENT_DIR_BIDIR |
| }; |
| |
| |
| struct conf_sig_trigger { |
| /* |
| * The RSSI / SNR threshold value. |
| * |
| * FIXME: what is the range? |
| */ |
| s16 threshold; |
| |
| /* |
| * Minimum delay between two trigger events for this trigger in ms. |
| * |
| * Range: 0 - 60000 |
| */ |
| u16 pacing; |
| |
| /* |
| * The measurement data source for this trigger. |
| * |
| * Range: CONF_TRIG_METRIC_* |
| */ |
| u8 metric; |
| |
| /* |
| * The trigger type of this trigger. |
| * |
| * Range: CONF_TRIG_EVENT_TYPE_* |
| */ |
| u8 type; |
| |
| /* |
| * The direction of the trigger. |
| * |
| * Range: CONF_TRIG_EVENT_DIR_* |
| */ |
| u8 direction; |
| |
| /* |
| * Hysteresis range of the trigger around the threshold (in dB) |
| * |
| * Range: u8 |
| */ |
| u8 hysteresis; |
| |
| /* |
| * Index of the trigger rule. |
| * |
| * Range: 0 - CONF_MAX_RSSI_SNR_TRIGGERS-1 |
| */ |
| u8 index; |
| |
| /* |
| * Enable / disable this rule (to use for clearing rules.) |
| * |
| * Range: 1 - Enabled, 2 - Not enabled |
| */ |
| u8 enable; |
| }; |
| |
| struct conf_sig_weights { |
| |
| /* |
| * RSSI from beacons average weight. |
| * |
| * Range: u8 |
| */ |
| u8 rssi_bcn_avg_weight; |
| |
| /* |
| * RSSI from data average weight. |
| * |
| * Range: u8 |
| */ |
| u8 rssi_pkt_avg_weight; |
| |
| /* |
| * SNR from beacons average weight. |
| * |
| * Range: u8 |
| */ |
| u8 snr_bcn_avg_weight; |
| |
| /* |
| * SNR from data average weight. |
| * |
| * Range: u8 |
| */ |
| u8 snr_pkt_avg_weight; |
| }; |
| |
| enum conf_bcn_filt_mode { |
| CONF_BCN_FILT_MODE_DISABLED = 0, |
| CONF_BCN_FILT_MODE_ENABLED = 1 |
| }; |
| |
| enum conf_bet_mode { |
| CONF_BET_MODE_DISABLE = 0, |
| CONF_BET_MODE_ENABLE = 1, |
| }; |
| |
| struct conf_conn_settings { |
| /* |
| * Firmware wakeup conditions configuration. The host may set only |
| * one bit. |
| * |
| * Range: CONF_WAKE_UP_EVENT_* |
| */ |
| u8 wake_up_event; |
| |
| /* |
| * Listen interval for beacons or Dtims. |
| * |
| * Range: 0 for beacon and Dtim wakeup |
| * 1-10 for x Dtims |
| * 1-255 for x beacons |
| */ |
| u8 listen_interval; |
| |
| /* |
| * Enable or disable the beacon filtering. |
| * |
| * Range: CONF_BCN_FILT_MODE_* |
| */ |
| enum conf_bcn_filt_mode bcn_filt_mode; |
| |
| /* |
| * Configure Beacon filter pass-thru rules. |
| */ |
| u8 bcn_filt_ie_count; |
| struct conf_bcn_filt_rule bcn_filt_ie[CONF_MAX_BCN_FILT_IE_COUNT]; |
| |
| /* |
| * The number of consequtive beacons to lose, before the firmware |
| * becomes out of synch. |
| * |
| * Range: u32 |
| */ |
| u32 synch_fail_thold; |
| |
| /* |
| * After out-of-synch, the number of TU's to wait without a further |
| * received beacon (or probe response) before issuing the BSS_EVENT_LOSE |
| * event. |
| * |
| * Range: u32 |
| */ |
| u32 bss_lose_timeout; |
| |
| /* |
| * Beacon receive timeout. |
| * |
| * Range: u32 |
| */ |
| u32 beacon_rx_timeout; |
| |
| /* |
| * Broadcast receive timeout. |
| * |
| * Range: u32 |
| */ |
| u32 broadcast_timeout; |
| |
| /* |
| * Enable/disable reception of broadcast packets in power save mode |
| * |
| * Range: 1 - enable, 0 - disable |
| */ |
| u8 rx_broadcast_in_ps; |
| |
| /* |
| * Consequtive PS Poll failures before sending event to driver |
| * |
| * Range: u8 |
| */ |
| u8 ps_poll_threshold; |
| |
| /* |
| * Configuration of signal (rssi/snr) triggers. |
| */ |
| u8 sig_trigger_count; |
| struct conf_sig_trigger sig_trigger[CONF_MAX_RSSI_SNR_TRIGGERS]; |
| |
| /* |
| * Configuration of signal average weights. |
| */ |
| struct conf_sig_weights sig_weights; |
| |
| /* |
| * Specifies if beacon early termination procedure is enabled or |
| * disabled. |
| * |
| * Range: CONF_BET_MODE_* |
| */ |
| u8 bet_enable; |
| |
| /* |
| * Specifies the maximum number of consecutive beacons that may be |
| * early terminated. After this number is reached at least one full |
| * beacon must be correctly received in FW before beacon ET |
| * resumes. |
| * |
| * Range 0 - 255 |
| */ |
| u8 bet_max_consecutive; |
| }; |
| |
| #define CONF_SR_ERR_TBL_MAX_VALUES 14 |
| |
| struct conf_mart_reflex_err_table { |
| /* |
| * Length of the error table values table. |
| * |
| * Range: 0 - CONF_SR_ERR_TBL_MAX_VALUES |
| */ |
| u8 len; |
| |
| /* |
| * Smart Reflex error table upper limit. |
| * |
| * Range: s8 |
| */ |
| s8 upper_limit; |
| |
| /* |
| * Smart Reflex error table values. |
| * |
| * Range: s8 |
| */ |
| s8 values[CONF_SR_ERR_TBL_MAX_VALUES]; |
| }; |
| |
| enum { |
| CONF_REF_CLK_19_2_E, |
| CONF_REF_CLK_26_E, |
| CONF_REF_CLK_38_4_E, |
| CONF_REF_CLK_52_E |
| }; |
| |
| enum single_dual_band_enum { |
| CONF_SINGLE_BAND, |
| CONF_DUAL_BAND |
| }; |
| |
| struct conf_general_parms { |
| /* |
| * RF Reference Clock type / speed |
| * |
| * Range: CONF_REF_CLK_* |
| */ |
| u8 ref_clk; |
| |
| /* |
| * Settling time of the reference clock after boot. |
| * |
| * Range: u8 |
| */ |
| u8 settling_time; |
| |
| /* |
| * Flag defining whether clock is valid on wakeup. |
| * |
| * Range: 0 - not valid on wakeup, 1 - valid on wakeup |
| */ |
| u8 clk_valid_on_wakeup; |
| |
| /* |
| * DC-to-DC mode. |
| * |
| * Range: Unknown |
| */ |
| u8 dc2dcmode; |
| |
| /* |
| * Flag defining whether used as single or dual-band. |
| * |
| * Range: CONF_SINGLE_BAND, CONF_DUAL_BAND |
| */ |
| u8 single_dual_band; |
| |
| /* |
| * TX bip fem autodetect flag. |
| * |
| * Range: Unknown |
| */ |
| u8 tx_bip_fem_autodetect; |
| |
| /* |
| * TX bip gem manufacturer. |
| * |
| * Range: Unknown |
| */ |
| u8 tx_bip_fem_manufacturer; |
| |
| /* |
| * Settings flags. |
| * |
| * Range: Unknown |
| */ |
| u8 settings; |
| }; |
| |
| #define CONF_RSSI_AND_PROCESS_COMPENSATION_SIZE 15 |
| #define CONF_NUMBER_OF_SUB_BANDS_5 7 |
| #define CONF_NUMBER_OF_RATE_GROUPS 6 |
| #define CONF_NUMBER_OF_CHANNELS_2_4 14 |
| #define CONF_NUMBER_OF_CHANNELS_5 35 |
| |
| struct conf_radio_parms { |
| /* |
| * Static radio parameters for 2.4GHz |
| * |
| * Range: unknown |
| */ |
| u8 rx_trace_loss; |
| u8 tx_trace_loss; |
| s8 rx_rssi_and_proc_compens[CONF_RSSI_AND_PROCESS_COMPENSATION_SIZE]; |
| |
| /* |
| * Static radio parameters for 5GHz |
| * |
| * Range: unknown |
| */ |
| u8 rx_trace_loss_5[CONF_NUMBER_OF_SUB_BANDS_5]; |
| u8 tx_trace_loss_5[CONF_NUMBER_OF_SUB_BANDS_5]; |
| s8 rx_rssi_and_proc_compens_5[CONF_RSSI_AND_PROCESS_COMPENSATION_SIZE]; |
| |
| /* |
| * Dynamic radio parameters for 2.4GHz |
| * |
| * Range: unknown |
| */ |
| s16 tx_ref_pd_voltage; |
| s8 tx_ref_power; |
| s8 tx_offset_db; |
| |
| s8 tx_rate_limits_normal[CONF_NUMBER_OF_RATE_GROUPS]; |
| s8 tx_rate_limits_degraded[CONF_NUMBER_OF_RATE_GROUPS]; |
| |
| s8 tx_channel_limits_11b[CONF_NUMBER_OF_CHANNELS_2_4]; |
| s8 tx_channel_limits_ofdm[CONF_NUMBER_OF_CHANNELS_2_4]; |
| s8 tx_pdv_rate_offsets[CONF_NUMBER_OF_RATE_GROUPS]; |
| |
| u8 tx_ibias[CONF_NUMBER_OF_RATE_GROUPS]; |
| u8 rx_fem_insertion_loss; |
| |
| /* |
| * Dynamic radio parameters for 5GHz |
| * |
| * Range: unknown |
| */ |
| s16 tx_ref_pd_voltage_5[CONF_NUMBER_OF_SUB_BANDS_5]; |
| s8 tx_ref_power_5[CONF_NUMBER_OF_SUB_BANDS_5]; |
| s8 tx_offset_db_5[CONF_NUMBER_OF_SUB_BANDS_5]; |
| |
| s8 tx_rate_limits_normal_5[CONF_NUMBER_OF_RATE_GROUPS]; |
| s8 tx_rate_limits_degraded_5[CONF_NUMBER_OF_RATE_GROUPS]; |
| |
| s8 tx_channel_limits_ofdm_5[CONF_NUMBER_OF_CHANNELS_5]; |
| s8 tx_pdv_rate_offsets_5[CONF_NUMBER_OF_RATE_GROUPS]; |
| |
| /* FIXME: this is inconsistent with the types for 2.4GHz */ |
| s8 tx_ibias_5[CONF_NUMBER_OF_RATE_GROUPS]; |
| s8 rx_fem_insertion_loss_5[CONF_NUMBER_OF_SUB_BANDS_5]; |
| }; |
| |
| #define CONF_SR_ERR_TBL_COUNT 3 |
| |
| struct conf_init_settings { |
| /* |
| * Configure Smart Reflex error table values. |
| */ |
| struct conf_mart_reflex_err_table sr_err_tbl[CONF_SR_ERR_TBL_COUNT]; |
| |
| /* |
| * Smart Reflex enable flag. |
| * |
| * Range: 1 - Smart Reflex enabled, 0 - Smart Reflex disabled |
| */ |
| u8 sr_enable; |
| |
| /* |
| * Configure general parameters. |
| */ |
| struct conf_general_parms genparam; |
| |
| /* |
| * Configure radio parameters. |
| */ |
| struct conf_radio_parms radioparam; |
| |
| }; |
| |
| struct conf_drv_settings { |
| struct conf_sg_settings sg; |
| struct conf_rx_settings rx; |
| struct conf_tx_settings tx; |
| struct conf_conn_settings conn; |
| struct conf_init_settings init; |
| }; |
| |
| #endif |