| /* |
| * PCI Express PCI Hot Plug Driver |
| * |
| * Copyright (C) 1995,2001 Compaq Computer Corporation |
| * Copyright (C) 2001 Greg Kroah-Hartman (greg@kroah.com) |
| * Copyright (C) 2001 IBM Corp. |
| * Copyright (C) 2003-2004 Intel Corporation |
| * |
| * All rights reserved. |
| * |
| * This program is free software; you can redistribute it and/or modify |
| * it under the terms of the GNU General Public License as published by |
| * the Free Software Foundation; either version 2 of the License, or (at |
| * your option) any later version. |
| * |
| * This program is distributed in the hope that it will be useful, but |
| * WITHOUT ANY WARRANTY; without even the implied warranty of |
| * MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE, GOOD TITLE or |
| * NON INFRINGEMENT. See the GNU General Public License for more |
| * details. |
| * |
| * You should have received a copy of the GNU General Public License |
| * along with this program; if not, write to the Free Software |
| * Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA. |
| * |
| * Send feedback to <greg@kroah.com>,<kristen.c.accardi@intel.com> |
| * |
| */ |
| |
| #include <linux/kernel.h> |
| #include <linux/module.h> |
| #include <linux/types.h> |
| #include <linux/signal.h> |
| #include <linux/jiffies.h> |
| #include <linux/timer.h> |
| #include <linux/pci.h> |
| #include <linux/interrupt.h> |
| #include <linux/time.h> |
| |
| #include "../pci.h" |
| #include "pciehp.h" |
| |
| static atomic_t pciehp_num_controllers = ATOMIC_INIT(0); |
| |
| struct ctrl_reg { |
| u8 cap_id; |
| u8 nxt_ptr; |
| u16 cap_reg; |
| u32 dev_cap; |
| u16 dev_ctrl; |
| u16 dev_status; |
| u32 lnk_cap; |
| u16 lnk_ctrl; |
| u16 lnk_status; |
| u32 slot_cap; |
| u16 slot_ctrl; |
| u16 slot_status; |
| u16 root_ctrl; |
| u16 rsvp; |
| u32 root_status; |
| } __attribute__ ((packed)); |
| |
| /* offsets to the controller registers based on the above structure layout */ |
| enum ctrl_offsets { |
| PCIECAPID = offsetof(struct ctrl_reg, cap_id), |
| NXTCAPPTR = offsetof(struct ctrl_reg, nxt_ptr), |
| CAPREG = offsetof(struct ctrl_reg, cap_reg), |
| DEVCAP = offsetof(struct ctrl_reg, dev_cap), |
| DEVCTRL = offsetof(struct ctrl_reg, dev_ctrl), |
| DEVSTATUS = offsetof(struct ctrl_reg, dev_status), |
| LNKCAP = offsetof(struct ctrl_reg, lnk_cap), |
| LNKCTRL = offsetof(struct ctrl_reg, lnk_ctrl), |
| LNKSTATUS = offsetof(struct ctrl_reg, lnk_status), |
| SLOTCAP = offsetof(struct ctrl_reg, slot_cap), |
| SLOTCTRL = offsetof(struct ctrl_reg, slot_ctrl), |
| SLOTSTATUS = offsetof(struct ctrl_reg, slot_status), |
| ROOTCTRL = offsetof(struct ctrl_reg, root_ctrl), |
| ROOTSTATUS = offsetof(struct ctrl_reg, root_status), |
| }; |
| |
| static inline int pciehp_readw(struct controller *ctrl, int reg, u16 *value) |
| { |
| struct pci_dev *dev = ctrl->pci_dev; |
| return pci_read_config_word(dev, ctrl->cap_base + reg, value); |
| } |
| |
| static inline int pciehp_readl(struct controller *ctrl, int reg, u32 *value) |
| { |
| struct pci_dev *dev = ctrl->pci_dev; |
| return pci_read_config_dword(dev, ctrl->cap_base + reg, value); |
| } |
| |
| static inline int pciehp_writew(struct controller *ctrl, int reg, u16 value) |
| { |
| struct pci_dev *dev = ctrl->pci_dev; |
| return pci_write_config_word(dev, ctrl->cap_base + reg, value); |
| } |
| |
| static inline int pciehp_writel(struct controller *ctrl, int reg, u32 value) |
| { |
| struct pci_dev *dev = ctrl->pci_dev; |
| return pci_write_config_dword(dev, ctrl->cap_base + reg, value); |
| } |
| |
| /* Field definitions in PCI Express Capabilities Register */ |
| #define CAP_VER 0x000F |
| #define DEV_PORT_TYPE 0x00F0 |
| #define SLOT_IMPL 0x0100 |
| #define MSG_NUM 0x3E00 |
| |
| /* Device or Port Type */ |
| #define NAT_ENDPT 0x00 |
| #define LEG_ENDPT 0x01 |
| #define ROOT_PORT 0x04 |
| #define UP_STREAM 0x05 |
| #define DN_STREAM 0x06 |
| #define PCIE_PCI_BRDG 0x07 |
| #define PCI_PCIE_BRDG 0x10 |
| |
| /* Field definitions in Device Capabilities Register */ |
| #define DATTN_BUTTN_PRSN 0x1000 |
| #define DATTN_LED_PRSN 0x2000 |
| #define DPWR_LED_PRSN 0x4000 |
| |
| /* Field definitions in Link Capabilities Register */ |
| #define MAX_LNK_SPEED 0x000F |
| #define MAX_LNK_WIDTH 0x03F0 |
| |
| /* Link Width Encoding */ |
| #define LNK_X1 0x01 |
| #define LNK_X2 0x02 |
| #define LNK_X4 0x04 |
| #define LNK_X8 0x08 |
| #define LNK_X12 0x0C |
| #define LNK_X16 0x10 |
| #define LNK_X32 0x20 |
| |
| /*Field definitions of Link Status Register */ |
| #define LNK_SPEED 0x000F |
| #define NEG_LINK_WD 0x03F0 |
| #define LNK_TRN_ERR 0x0400 |
| #define LNK_TRN 0x0800 |
| #define SLOT_CLK_CONF 0x1000 |
| |
| /* Field definitions in Slot Capabilities Register */ |
| #define ATTN_BUTTN_PRSN 0x00000001 |
| #define PWR_CTRL_PRSN 0x00000002 |
| #define MRL_SENS_PRSN 0x00000004 |
| #define ATTN_LED_PRSN 0x00000008 |
| #define PWR_LED_PRSN 0x00000010 |
| #define HP_SUPR_RM_SUP 0x00000020 |
| #define HP_CAP 0x00000040 |
| #define SLOT_PWR_VALUE 0x000003F8 |
| #define SLOT_PWR_LIMIT 0x00000C00 |
| #define PSN 0xFFF80000 /* PSN: Physical Slot Number */ |
| |
| /* Field definitions in Slot Control Register */ |
| #define ATTN_BUTTN_ENABLE 0x0001 |
| #define PWR_FAULT_DETECT_ENABLE 0x0002 |
| #define MRL_DETECT_ENABLE 0x0004 |
| #define PRSN_DETECT_ENABLE 0x0008 |
| #define CMD_CMPL_INTR_ENABLE 0x0010 |
| #define HP_INTR_ENABLE 0x0020 |
| #define ATTN_LED_CTRL 0x00C0 |
| #define PWR_LED_CTRL 0x0300 |
| #define PWR_CTRL 0x0400 |
| #define EMI_CTRL 0x0800 |
| |
| /* Attention indicator and Power indicator states */ |
| #define LED_ON 0x01 |
| #define LED_BLINK 0x10 |
| #define LED_OFF 0x11 |
| |
| /* Power Control Command */ |
| #define POWER_ON 0 |
| #define POWER_OFF 0x0400 |
| |
| /* EMI Status defines */ |
| #define EMI_DISENGAGED 0 |
| #define EMI_ENGAGED 1 |
| |
| /* Field definitions in Slot Status Register */ |
| #define ATTN_BUTTN_PRESSED 0x0001 |
| #define PWR_FAULT_DETECTED 0x0002 |
| #define MRL_SENS_CHANGED 0x0004 |
| #define PRSN_DETECT_CHANGED 0x0008 |
| #define CMD_COMPLETED 0x0010 |
| #define MRL_STATE 0x0020 |
| #define PRSN_STATE 0x0040 |
| #define EMI_STATE 0x0080 |
| #define EMI_STATUS_BIT 7 |
| |
| static irqreturn_t pcie_isr(int irq, void *dev_id); |
| static void start_int_poll_timer(struct controller *ctrl, int sec); |
| |
| /* This is the interrupt polling timeout function. */ |
| static void int_poll_timeout(unsigned long data) |
| { |
| struct controller *ctrl = (struct controller *)data; |
| |
| /* Poll for interrupt events. regs == NULL => polling */ |
| pcie_isr(0, ctrl); |
| |
| init_timer(&ctrl->poll_timer); |
| if (!pciehp_poll_time) |
| pciehp_poll_time = 2; /* default polling interval is 2 sec */ |
| |
| start_int_poll_timer(ctrl, pciehp_poll_time); |
| } |
| |
| /* This function starts the interrupt polling timer. */ |
| static void start_int_poll_timer(struct controller *ctrl, int sec) |
| { |
| /* Clamp to sane value */ |
| if ((sec <= 0) || (sec > 60)) |
| sec = 2; |
| |
| ctrl->poll_timer.function = &int_poll_timeout; |
| ctrl->poll_timer.data = (unsigned long)ctrl; |
| ctrl->poll_timer.expires = jiffies + sec * HZ; |
| add_timer(&ctrl->poll_timer); |
| } |
| |
| static inline int pcie_wait_cmd(struct controller *ctrl) |
| { |
| int retval = 0; |
| unsigned int msecs = pciehp_poll_mode ? 2500 : 1000; |
| unsigned long timeout = msecs_to_jiffies(msecs); |
| int rc; |
| |
| rc = wait_event_interruptible_timeout(ctrl->queue, |
| !ctrl->cmd_busy, timeout); |
| if (!rc) |
| dbg("Command not completed in 1000 msec\n"); |
| else if (rc < 0) { |
| retval = -EINTR; |
| info("Command was interrupted by a signal\n"); |
| } |
| |
| return retval; |
| } |
| |
| /** |
| * pcie_write_cmd - Issue controller command |
| * @slot: slot to which the command is issued |
| * @cmd: command value written to slot control register |
| * @mask: bitmask of slot control register to be modified |
| */ |
| static int pcie_write_cmd(struct slot *slot, u16 cmd, u16 mask) |
| { |
| struct controller *ctrl = slot->ctrl; |
| int retval = 0; |
| u16 slot_status; |
| u16 slot_ctrl; |
| unsigned long flags; |
| |
| mutex_lock(&ctrl->ctrl_lock); |
| |
| retval = pciehp_readw(ctrl, SLOTSTATUS, &slot_status); |
| if (retval) { |
| err("%s: Cannot read SLOTSTATUS register\n", __FUNCTION__); |
| goto out; |
| } |
| |
| if ((slot_status & CMD_COMPLETED) == CMD_COMPLETED ) { |
| /* After 1 sec and CMD_COMPLETED still not set, just |
| proceed forward to issue the next command according |
| to spec. Just print out the error message */ |
| dbg("%s: CMD_COMPLETED not clear after 1 sec.\n", |
| __FUNCTION__); |
| } |
| |
| spin_lock_irqsave(&ctrl->lock, flags); |
| retval = pciehp_readw(ctrl, SLOTCTRL, &slot_ctrl); |
| if (retval) { |
| err("%s: Cannot read SLOTCTRL register\n", __FUNCTION__); |
| goto out_spin_unlock; |
| } |
| |
| slot_ctrl &= ~mask; |
| slot_ctrl |= ((cmd & mask) | CMD_CMPL_INTR_ENABLE); |
| |
| ctrl->cmd_busy = 1; |
| retval = pciehp_writew(ctrl, SLOTCTRL, slot_ctrl); |
| if (retval) |
| err("%s: Cannot write to SLOTCTRL register\n", __FUNCTION__); |
| |
| out_spin_unlock: |
| spin_unlock_irqrestore(&ctrl->lock, flags); |
| |
| /* |
| * Wait for command completion. |
| */ |
| if (!retval) |
| retval = pcie_wait_cmd(ctrl); |
| out: |
| mutex_unlock(&ctrl->ctrl_lock); |
| return retval; |
| } |
| |
| static int hpc_check_lnk_status(struct controller *ctrl) |
| { |
| u16 lnk_status; |
| int retval = 0; |
| |
| retval = pciehp_readw(ctrl, LNKSTATUS, &lnk_status); |
| if (retval) { |
| err("%s: Cannot read LNKSTATUS register\n", __FUNCTION__); |
| return retval; |
| } |
| |
| dbg("%s: lnk_status = %x\n", __FUNCTION__, lnk_status); |
| if ( (lnk_status & LNK_TRN) || (lnk_status & LNK_TRN_ERR) || |
| !(lnk_status & NEG_LINK_WD)) { |
| err("%s : Link Training Error occurs \n", __FUNCTION__); |
| retval = -1; |
| return retval; |
| } |
| |
| return retval; |
| } |
| |
| static int hpc_get_attention_status(struct slot *slot, u8 *status) |
| { |
| struct controller *ctrl = slot->ctrl; |
| u16 slot_ctrl; |
| u8 atten_led_state; |
| int retval = 0; |
| |
| retval = pciehp_readw(ctrl, SLOTCTRL, &slot_ctrl); |
| if (retval) { |
| err("%s: Cannot read SLOTCTRL register\n", __FUNCTION__); |
| return retval; |
| } |
| |
| dbg("%s: SLOTCTRL %x, value read %x\n", |
| __FUNCTION__, ctrl->cap_base + SLOTCTRL, slot_ctrl); |
| |
| atten_led_state = (slot_ctrl & ATTN_LED_CTRL) >> 6; |
| |
| switch (atten_led_state) { |
| case 0: |
| *status = 0xFF; /* Reserved */ |
| break; |
| case 1: |
| *status = 1; /* On */ |
| break; |
| case 2: |
| *status = 2; /* Blink */ |
| break; |
| case 3: |
| *status = 0; /* Off */ |
| break; |
| default: |
| *status = 0xFF; |
| break; |
| } |
| |
| return 0; |
| } |
| |
| static int hpc_get_power_status(struct slot *slot, u8 *status) |
| { |
| struct controller *ctrl = slot->ctrl; |
| u16 slot_ctrl; |
| u8 pwr_state; |
| int retval = 0; |
| |
| retval = pciehp_readw(ctrl, SLOTCTRL, &slot_ctrl); |
| if (retval) { |
| err("%s: Cannot read SLOTCTRL register\n", __FUNCTION__); |
| return retval; |
| } |
| dbg("%s: SLOTCTRL %x value read %x\n", |
| __FUNCTION__, ctrl->cap_base + SLOTCTRL, slot_ctrl); |
| |
| pwr_state = (slot_ctrl & PWR_CTRL) >> 10; |
| |
| switch (pwr_state) { |
| case 0: |
| *status = 1; |
| break; |
| case 1: |
| *status = 0; |
| break; |
| default: |
| *status = 0xFF; |
| break; |
| } |
| |
| return retval; |
| } |
| |
| static int hpc_get_latch_status(struct slot *slot, u8 *status) |
| { |
| struct controller *ctrl = slot->ctrl; |
| u16 slot_status; |
| int retval = 0; |
| |
| retval = pciehp_readw(ctrl, SLOTSTATUS, &slot_status); |
| if (retval) { |
| err("%s: Cannot read SLOTSTATUS register\n", __FUNCTION__); |
| return retval; |
| } |
| |
| *status = (((slot_status & MRL_STATE) >> 5) == 0) ? 0 : 1; |
| |
| return 0; |
| } |
| |
| static int hpc_get_adapter_status(struct slot *slot, u8 *status) |
| { |
| struct controller *ctrl = slot->ctrl; |
| u16 slot_status; |
| u8 card_state; |
| int retval = 0; |
| |
| retval = pciehp_readw(ctrl, SLOTSTATUS, &slot_status); |
| if (retval) { |
| err("%s: Cannot read SLOTSTATUS register\n", __FUNCTION__); |
| return retval; |
| } |
| card_state = (u8)((slot_status & PRSN_STATE) >> 6); |
| *status = (card_state == 1) ? 1 : 0; |
| |
| return 0; |
| } |
| |
| static int hpc_query_power_fault(struct slot *slot) |
| { |
| struct controller *ctrl = slot->ctrl; |
| u16 slot_status; |
| u8 pwr_fault; |
| int retval = 0; |
| |
| retval = pciehp_readw(ctrl, SLOTSTATUS, &slot_status); |
| if (retval) { |
| err("%s: Cannot check for power fault\n", __FUNCTION__); |
| return retval; |
| } |
| pwr_fault = (u8)((slot_status & PWR_FAULT_DETECTED) >> 1); |
| |
| return pwr_fault; |
| } |
| |
| static int hpc_get_emi_status(struct slot *slot, u8 *status) |
| { |
| struct controller *ctrl = slot->ctrl; |
| u16 slot_status; |
| int retval = 0; |
| |
| retval = pciehp_readw(ctrl, SLOTSTATUS, &slot_status); |
| if (retval) { |
| err("%s : Cannot check EMI status\n", __FUNCTION__); |
| return retval; |
| } |
| *status = (slot_status & EMI_STATE) >> EMI_STATUS_BIT; |
| |
| return retval; |
| } |
| |
| static int hpc_toggle_emi(struct slot *slot) |
| { |
| u16 slot_cmd; |
| u16 cmd_mask; |
| int rc; |
| |
| slot_cmd = EMI_CTRL; |
| cmd_mask = EMI_CTRL; |
| if (!pciehp_poll_mode) { |
| slot_cmd = slot_cmd | HP_INTR_ENABLE; |
| cmd_mask = cmd_mask | HP_INTR_ENABLE; |
| } |
| |
| rc = pcie_write_cmd(slot, slot_cmd, cmd_mask); |
| slot->last_emi_toggle = get_seconds(); |
| |
| return rc; |
| } |
| |
| static int hpc_set_attention_status(struct slot *slot, u8 value) |
| { |
| struct controller *ctrl = slot->ctrl; |
| u16 slot_cmd; |
| u16 cmd_mask; |
| int rc; |
| |
| cmd_mask = ATTN_LED_CTRL; |
| switch (value) { |
| case 0 : /* turn off */ |
| slot_cmd = 0x00C0; |
| break; |
| case 1: /* turn on */ |
| slot_cmd = 0x0040; |
| break; |
| case 2: /* turn blink */ |
| slot_cmd = 0x0080; |
| break; |
| default: |
| return -1; |
| } |
| if (!pciehp_poll_mode) { |
| slot_cmd = slot_cmd | HP_INTR_ENABLE; |
| cmd_mask = cmd_mask | HP_INTR_ENABLE; |
| } |
| |
| rc = pcie_write_cmd(slot, slot_cmd, cmd_mask); |
| dbg("%s: SLOTCTRL %x write cmd %x\n", |
| __FUNCTION__, ctrl->cap_base + SLOTCTRL, slot_cmd); |
| |
| return rc; |
| } |
| |
| static void hpc_set_green_led_on(struct slot *slot) |
| { |
| struct controller *ctrl = slot->ctrl; |
| u16 slot_cmd; |
| u16 cmd_mask; |
| |
| slot_cmd = 0x0100; |
| cmd_mask = PWR_LED_CTRL; |
| if (!pciehp_poll_mode) { |
| slot_cmd = slot_cmd | HP_INTR_ENABLE; |
| cmd_mask = cmd_mask | HP_INTR_ENABLE; |
| } |
| |
| pcie_write_cmd(slot, slot_cmd, cmd_mask); |
| |
| dbg("%s: SLOTCTRL %x write cmd %x\n", |
| __FUNCTION__, ctrl->cap_base + SLOTCTRL, slot_cmd); |
| } |
| |
| static void hpc_set_green_led_off(struct slot *slot) |
| { |
| struct controller *ctrl = slot->ctrl; |
| u16 slot_cmd; |
| u16 cmd_mask; |
| |
| slot_cmd = 0x0300; |
| cmd_mask = PWR_LED_CTRL; |
| if (!pciehp_poll_mode) { |
| slot_cmd = slot_cmd | HP_INTR_ENABLE; |
| cmd_mask = cmd_mask | HP_INTR_ENABLE; |
| } |
| |
| pcie_write_cmd(slot, slot_cmd, cmd_mask); |
| dbg("%s: SLOTCTRL %x write cmd %x\n", |
| __FUNCTION__, ctrl->cap_base + SLOTCTRL, slot_cmd); |
| } |
| |
| static void hpc_set_green_led_blink(struct slot *slot) |
| { |
| struct controller *ctrl = slot->ctrl; |
| u16 slot_cmd; |
| u16 cmd_mask; |
| |
| slot_cmd = 0x0200; |
| cmd_mask = PWR_LED_CTRL; |
| if (!pciehp_poll_mode) { |
| slot_cmd = slot_cmd | HP_INTR_ENABLE; |
| cmd_mask = cmd_mask | HP_INTR_ENABLE; |
| } |
| |
| pcie_write_cmd(slot, slot_cmd, cmd_mask); |
| |
| dbg("%s: SLOTCTRL %x write cmd %x\n", |
| __FUNCTION__, ctrl->cap_base + SLOTCTRL, slot_cmd); |
| } |
| |
| static void hpc_release_ctlr(struct controller *ctrl) |
| { |
| if (pciehp_poll_mode) |
| del_timer(&ctrl->poll_timer); |
| else |
| free_irq(ctrl->pci_dev->irq, ctrl); |
| |
| /* |
| * If this is the last controller to be released, destroy the |
| * pciehp work queue |
| */ |
| if (atomic_dec_and_test(&pciehp_num_controllers)) |
| destroy_workqueue(pciehp_wq); |
| } |
| |
| static int hpc_power_on_slot(struct slot * slot) |
| { |
| struct controller *ctrl = slot->ctrl; |
| u16 slot_cmd; |
| u16 cmd_mask; |
| u16 slot_status; |
| int retval = 0; |
| |
| dbg("%s: slot->hp_slot %x\n", __FUNCTION__, slot->hp_slot); |
| |
| /* Clear sticky power-fault bit from previous power failures */ |
| retval = pciehp_readw(ctrl, SLOTSTATUS, &slot_status); |
| if (retval) { |
| err("%s: Cannot read SLOTSTATUS register\n", __FUNCTION__); |
| return retval; |
| } |
| slot_status &= PWR_FAULT_DETECTED; |
| if (slot_status) { |
| retval = pciehp_writew(ctrl, SLOTSTATUS, slot_status); |
| if (retval) { |
| err("%s: Cannot write to SLOTSTATUS register\n", |
| __FUNCTION__); |
| return retval; |
| } |
| } |
| |
| slot_cmd = POWER_ON; |
| cmd_mask = PWR_CTRL; |
| /* Enable detection that we turned off at slot power-off time */ |
| if (!pciehp_poll_mode) { |
| slot_cmd = slot_cmd | |
| PWR_FAULT_DETECT_ENABLE | |
| MRL_DETECT_ENABLE | |
| PRSN_DETECT_ENABLE | |
| HP_INTR_ENABLE; |
| cmd_mask = cmd_mask | |
| PWR_FAULT_DETECT_ENABLE | |
| MRL_DETECT_ENABLE | |
| PRSN_DETECT_ENABLE | |
| HP_INTR_ENABLE; |
| } |
| |
| retval = pcie_write_cmd(slot, slot_cmd, cmd_mask); |
| |
| if (retval) { |
| err("%s: Write %x command failed!\n", __FUNCTION__, slot_cmd); |
| return -1; |
| } |
| dbg("%s: SLOTCTRL %x write cmd %x\n", |
| __FUNCTION__, ctrl->cap_base + SLOTCTRL, slot_cmd); |
| |
| return retval; |
| } |
| |
| static int hpc_power_off_slot(struct slot * slot) |
| { |
| struct controller *ctrl = slot->ctrl; |
| u16 slot_cmd; |
| u16 cmd_mask; |
| int retval = 0; |
| |
| dbg("%s: slot->hp_slot %x\n", __FUNCTION__, slot->hp_slot); |
| |
| slot_cmd = POWER_OFF; |
| cmd_mask = PWR_CTRL; |
| /* |
| * If we get MRL or presence detect interrupts now, the isr |
| * will notice the sticky power-fault bit too and issue power |
| * indicator change commands. This will lead to an endless loop |
| * of command completions, since the power-fault bit remains on |
| * till the slot is powered on again. |
| */ |
| if (!pciehp_poll_mode) { |
| slot_cmd = (slot_cmd & |
| ~PWR_FAULT_DETECT_ENABLE & |
| ~MRL_DETECT_ENABLE & |
| ~PRSN_DETECT_ENABLE) | HP_INTR_ENABLE; |
| cmd_mask = cmd_mask | |
| PWR_FAULT_DETECT_ENABLE | |
| MRL_DETECT_ENABLE | |
| PRSN_DETECT_ENABLE | |
| HP_INTR_ENABLE; |
| } |
| |
| retval = pcie_write_cmd(slot, slot_cmd, cmd_mask); |
| if (retval) { |
| err("%s: Write command failed!\n", __FUNCTION__); |
| return -1; |
| } |
| dbg("%s: SLOTCTRL %x write cmd %x\n", |
| __FUNCTION__, ctrl->cap_base + SLOTCTRL, slot_cmd); |
| |
| return retval; |
| } |
| |
| static irqreturn_t pcie_isr(int irq, void *dev_id) |
| { |
| struct controller *ctrl = (struct controller *)dev_id; |
| u16 slot_status, intr_detect, intr_loc; |
| u16 temp_word; |
| int hp_slot = 0; /* only 1 slot per PCI Express port */ |
| int rc = 0; |
| unsigned long flags; |
| |
| rc = pciehp_readw(ctrl, SLOTSTATUS, &slot_status); |
| if (rc) { |
| err("%s: Cannot read SLOTSTATUS register\n", __FUNCTION__); |
| return IRQ_NONE; |
| } |
| |
| intr_detect = (ATTN_BUTTN_PRESSED | PWR_FAULT_DETECTED | |
| MRL_SENS_CHANGED | PRSN_DETECT_CHANGED | CMD_COMPLETED); |
| |
| intr_loc = slot_status & intr_detect; |
| |
| /* Check to see if it was our interrupt */ |
| if ( !intr_loc ) |
| return IRQ_NONE; |
| |
| dbg("%s: intr_loc %x\n", __FUNCTION__, intr_loc); |
| /* Mask Hot-plug Interrupt Enable */ |
| if (!pciehp_poll_mode) { |
| spin_lock_irqsave(&ctrl->lock, flags); |
| rc = pciehp_readw(ctrl, SLOTCTRL, &temp_word); |
| if (rc) { |
| err("%s: Cannot read SLOT_CTRL register\n", |
| __FUNCTION__); |
| spin_unlock_irqrestore(&ctrl->lock, flags); |
| return IRQ_NONE; |
| } |
| |
| dbg("%s: pciehp_readw(SLOTCTRL) with value %x\n", |
| __FUNCTION__, temp_word); |
| temp_word = (temp_word & ~HP_INTR_ENABLE & |
| ~CMD_CMPL_INTR_ENABLE) | 0x00; |
| rc = pciehp_writew(ctrl, SLOTCTRL, temp_word); |
| if (rc) { |
| err("%s: Cannot write to SLOTCTRL register\n", |
| __FUNCTION__); |
| spin_unlock_irqrestore(&ctrl->lock, flags); |
| return IRQ_NONE; |
| } |
| spin_unlock_irqrestore(&ctrl->lock, flags); |
| |
| rc = pciehp_readw(ctrl, SLOTSTATUS, &slot_status); |
| if (rc) { |
| err("%s: Cannot read SLOT_STATUS register\n", |
| __FUNCTION__); |
| return IRQ_NONE; |
| } |
| dbg("%s: pciehp_readw(SLOTSTATUS) with value %x\n", |
| __FUNCTION__, slot_status); |
| |
| /* Clear command complete interrupt caused by this write */ |
| temp_word = 0x1f; |
| rc = pciehp_writew(ctrl, SLOTSTATUS, temp_word); |
| if (rc) { |
| err("%s: Cannot write to SLOTSTATUS register\n", |
| __FUNCTION__); |
| return IRQ_NONE; |
| } |
| } |
| |
| if (intr_loc & CMD_COMPLETED) { |
| /* |
| * Command Complete Interrupt Pending |
| */ |
| ctrl->cmd_busy = 0; |
| wake_up_interruptible(&ctrl->queue); |
| } |
| |
| if (intr_loc & MRL_SENS_CHANGED) |
| pciehp_handle_switch_change(hp_slot, ctrl); |
| |
| if (intr_loc & ATTN_BUTTN_PRESSED) |
| pciehp_handle_attention_button(hp_slot, ctrl); |
| |
| if (intr_loc & PRSN_DETECT_CHANGED) |
| pciehp_handle_presence_change(hp_slot, ctrl); |
| |
| if (intr_loc & PWR_FAULT_DETECTED) |
| pciehp_handle_power_fault(hp_slot, ctrl); |
| |
| /* Clear all events after serving them */ |
| temp_word = 0x1F; |
| rc = pciehp_writew(ctrl, SLOTSTATUS, temp_word); |
| if (rc) { |
| err("%s: Cannot write to SLOTSTATUS register\n", __FUNCTION__); |
| return IRQ_NONE; |
| } |
| /* Unmask Hot-plug Interrupt Enable */ |
| if (!pciehp_poll_mode) { |
| spin_lock_irqsave(&ctrl->lock, flags); |
| rc = pciehp_readw(ctrl, SLOTCTRL, &temp_word); |
| if (rc) { |
| err("%s: Cannot read SLOTCTRL register\n", |
| __FUNCTION__); |
| spin_unlock_irqrestore(&ctrl->lock, flags); |
| return IRQ_NONE; |
| } |
| |
| dbg("%s: Unmask Hot-plug Interrupt Enable\n", __FUNCTION__); |
| temp_word = (temp_word & ~HP_INTR_ENABLE) | HP_INTR_ENABLE; |
| |
| rc = pciehp_writew(ctrl, SLOTCTRL, temp_word); |
| if (rc) { |
| err("%s: Cannot write to SLOTCTRL register\n", |
| __FUNCTION__); |
| spin_unlock_irqrestore(&ctrl->lock, flags); |
| return IRQ_NONE; |
| } |
| spin_unlock_irqrestore(&ctrl->lock, flags); |
| |
| rc = pciehp_readw(ctrl, SLOTSTATUS, &slot_status); |
| if (rc) { |
| err("%s: Cannot read SLOT_STATUS register\n", |
| __FUNCTION__); |
| return IRQ_NONE; |
| } |
| |
| /* Clear command complete interrupt caused by this write */ |
| temp_word = 0x1F; |
| rc = pciehp_writew(ctrl, SLOTSTATUS, temp_word); |
| if (rc) { |
| err("%s: Cannot write to SLOTSTATUS failed\n", |
| __FUNCTION__); |
| return IRQ_NONE; |
| } |
| dbg("%s: pciehp_writew(SLOTSTATUS) with value %x\n", |
| __FUNCTION__, temp_word); |
| } |
| |
| return IRQ_HANDLED; |
| } |
| |
| static int hpc_get_max_lnk_speed(struct slot *slot, enum pci_bus_speed *value) |
| { |
| struct controller *ctrl = slot->ctrl; |
| enum pcie_link_speed lnk_speed; |
| u32 lnk_cap; |
| int retval = 0; |
| |
| retval = pciehp_readl(ctrl, LNKCAP, &lnk_cap); |
| if (retval) { |
| err("%s: Cannot read LNKCAP register\n", __FUNCTION__); |
| return retval; |
| } |
| |
| switch (lnk_cap & 0x000F) { |
| case 1: |
| lnk_speed = PCIE_2PT5GB; |
| break; |
| default: |
| lnk_speed = PCIE_LNK_SPEED_UNKNOWN; |
| break; |
| } |
| |
| *value = lnk_speed; |
| dbg("Max link speed = %d\n", lnk_speed); |
| |
| return retval; |
| } |
| |
| static int hpc_get_max_lnk_width(struct slot *slot, |
| enum pcie_link_width *value) |
| { |
| struct controller *ctrl = slot->ctrl; |
| enum pcie_link_width lnk_wdth; |
| u32 lnk_cap; |
| int retval = 0; |
| |
| retval = pciehp_readl(ctrl, LNKCAP, &lnk_cap); |
| if (retval) { |
| err("%s: Cannot read LNKCAP register\n", __FUNCTION__); |
| return retval; |
| } |
| |
| switch ((lnk_cap & 0x03F0) >> 4){ |
| case 0: |
| lnk_wdth = PCIE_LNK_WIDTH_RESRV; |
| break; |
| case 1: |
| lnk_wdth = PCIE_LNK_X1; |
| break; |
| case 2: |
| lnk_wdth = PCIE_LNK_X2; |
| break; |
| case 4: |
| lnk_wdth = PCIE_LNK_X4; |
| break; |
| case 8: |
| lnk_wdth = PCIE_LNK_X8; |
| break; |
| case 12: |
| lnk_wdth = PCIE_LNK_X12; |
| break; |
| case 16: |
| lnk_wdth = PCIE_LNK_X16; |
| break; |
| case 32: |
| lnk_wdth = PCIE_LNK_X32; |
| break; |
| default: |
| lnk_wdth = PCIE_LNK_WIDTH_UNKNOWN; |
| break; |
| } |
| |
| *value = lnk_wdth; |
| dbg("Max link width = %d\n", lnk_wdth); |
| |
| return retval; |
| } |
| |
| static int hpc_get_cur_lnk_speed(struct slot *slot, enum pci_bus_speed *value) |
| { |
| struct controller *ctrl = slot->ctrl; |
| enum pcie_link_speed lnk_speed = PCI_SPEED_UNKNOWN; |
| int retval = 0; |
| u16 lnk_status; |
| |
| retval = pciehp_readw(ctrl, LNKSTATUS, &lnk_status); |
| if (retval) { |
| err("%s: Cannot read LNKSTATUS register\n", __FUNCTION__); |
| return retval; |
| } |
| |
| switch (lnk_status & 0x0F) { |
| case 1: |
| lnk_speed = PCIE_2PT5GB; |
| break; |
| default: |
| lnk_speed = PCIE_LNK_SPEED_UNKNOWN; |
| break; |
| } |
| |
| *value = lnk_speed; |
| dbg("Current link speed = %d\n", lnk_speed); |
| |
| return retval; |
| } |
| |
| static int hpc_get_cur_lnk_width(struct slot *slot, |
| enum pcie_link_width *value) |
| { |
| struct controller *ctrl = slot->ctrl; |
| enum pcie_link_width lnk_wdth = PCIE_LNK_WIDTH_UNKNOWN; |
| int retval = 0; |
| u16 lnk_status; |
| |
| retval = pciehp_readw(ctrl, LNKSTATUS, &lnk_status); |
| if (retval) { |
| err("%s: Cannot read LNKSTATUS register\n", __FUNCTION__); |
| return retval; |
| } |
| |
| switch ((lnk_status & 0x03F0) >> 4){ |
| case 0: |
| lnk_wdth = PCIE_LNK_WIDTH_RESRV; |
| break; |
| case 1: |
| lnk_wdth = PCIE_LNK_X1; |
| break; |
| case 2: |
| lnk_wdth = PCIE_LNK_X2; |
| break; |
| case 4: |
| lnk_wdth = PCIE_LNK_X4; |
| break; |
| case 8: |
| lnk_wdth = PCIE_LNK_X8; |
| break; |
| case 12: |
| lnk_wdth = PCIE_LNK_X12; |
| break; |
| case 16: |
| lnk_wdth = PCIE_LNK_X16; |
| break; |
| case 32: |
| lnk_wdth = PCIE_LNK_X32; |
| break; |
| default: |
| lnk_wdth = PCIE_LNK_WIDTH_UNKNOWN; |
| break; |
| } |
| |
| *value = lnk_wdth; |
| dbg("Current link width = %d\n", lnk_wdth); |
| |
| return retval; |
| } |
| |
| static struct hpc_ops pciehp_hpc_ops = { |
| .power_on_slot = hpc_power_on_slot, |
| .power_off_slot = hpc_power_off_slot, |
| .set_attention_status = hpc_set_attention_status, |
| .get_power_status = hpc_get_power_status, |
| .get_attention_status = hpc_get_attention_status, |
| .get_latch_status = hpc_get_latch_status, |
| .get_adapter_status = hpc_get_adapter_status, |
| .get_emi_status = hpc_get_emi_status, |
| .toggle_emi = hpc_toggle_emi, |
| |
| .get_max_bus_speed = hpc_get_max_lnk_speed, |
| .get_cur_bus_speed = hpc_get_cur_lnk_speed, |
| .get_max_lnk_width = hpc_get_max_lnk_width, |
| .get_cur_lnk_width = hpc_get_cur_lnk_width, |
| |
| .query_power_fault = hpc_query_power_fault, |
| .green_led_on = hpc_set_green_led_on, |
| .green_led_off = hpc_set_green_led_off, |
| .green_led_blink = hpc_set_green_led_blink, |
| |
| .release_ctlr = hpc_release_ctlr, |
| .check_lnk_status = hpc_check_lnk_status, |
| }; |
| |
| #ifdef CONFIG_ACPI |
| int pciehp_acpi_get_hp_hw_control_from_firmware(struct pci_dev *dev) |
| { |
| acpi_status status; |
| acpi_handle chandle, handle = DEVICE_ACPI_HANDLE(&(dev->dev)); |
| struct pci_dev *pdev = dev; |
| struct pci_bus *parent; |
| struct acpi_buffer string = { ACPI_ALLOCATE_BUFFER, NULL }; |
| |
| /* |
| * Per PCI firmware specification, we should run the ACPI _OSC |
| * method to get control of hotplug hardware before using it. |
| * If an _OSC is missing, we look for an OSHP to do the same thing. |
| * To handle different BIOS behavior, we look for _OSC and OSHP |
| * within the scope of the hotplug controller and its parents, upto |
| * the host bridge under which this controller exists. |
| */ |
| while (!handle) { |
| /* |
| * This hotplug controller was not listed in the ACPI name |
| * space at all. Try to get acpi handle of parent pci bus. |
| */ |
| if (!pdev || !pdev->bus->parent) |
| break; |
| parent = pdev->bus->parent; |
| dbg("Could not find %s in acpi namespace, trying parent\n", |
| pci_name(pdev)); |
| if (!parent->self) |
| /* Parent must be a host bridge */ |
| handle = acpi_get_pci_rootbridge_handle( |
| pci_domain_nr(parent), |
| parent->number); |
| else |
| handle = DEVICE_ACPI_HANDLE( |
| &(parent->self->dev)); |
| pdev = parent->self; |
| } |
| |
| while (handle) { |
| acpi_get_name(handle, ACPI_FULL_PATHNAME, &string); |
| dbg("Trying to get hotplug control for %s \n", |
| (char *)string.pointer); |
| status = pci_osc_control_set(handle, |
| OSC_PCI_EXPRESS_CAP_STRUCTURE_CONTROL | |
| OSC_PCI_EXPRESS_NATIVE_HP_CONTROL); |
| if (status == AE_NOT_FOUND) |
| status = acpi_run_oshp(handle); |
| if (ACPI_SUCCESS(status)) { |
| dbg("Gained control for hotplug HW for pci %s (%s)\n", |
| pci_name(dev), (char *)string.pointer); |
| kfree(string.pointer); |
| return 0; |
| } |
| if (acpi_root_bridge(handle)) |
| break; |
| chandle = handle; |
| status = acpi_get_parent(chandle, &handle); |
| if (ACPI_FAILURE(status)) |
| break; |
| } |
| |
| err("Cannot get control of hotplug hardware for pci %s\n", |
| pci_name(dev)); |
| |
| kfree(string.pointer); |
| return -1; |
| } |
| #endif |
| |
| int pcie_init(struct controller * ctrl, struct pcie_device *dev) |
| { |
| int rc; |
| u16 temp_word; |
| u16 cap_reg; |
| u16 intr_enable = 0; |
| u32 slot_cap; |
| int cap_base; |
| u16 slot_status, slot_ctrl; |
| struct pci_dev *pdev; |
| |
| pdev = dev->port; |
| ctrl->pci_dev = pdev; /* save pci_dev in context */ |
| |
| dbg("%s: hotplug controller vendor id 0x%x device id 0x%x\n", |
| __FUNCTION__, pdev->vendor, pdev->device); |
| |
| if ((cap_base = pci_find_capability(pdev, PCI_CAP_ID_EXP)) == 0) { |
| dbg("%s: Can't find PCI_CAP_ID_EXP (0x10)\n", __FUNCTION__); |
| goto abort_free_ctlr; |
| } |
| |
| ctrl->cap_base = cap_base; |
| |
| dbg("%s: pcie_cap_base %x\n", __FUNCTION__, cap_base); |
| |
| rc = pciehp_readw(ctrl, CAPREG, &cap_reg); |
| if (rc) { |
| err("%s: Cannot read CAPREG register\n", __FUNCTION__); |
| goto abort_free_ctlr; |
| } |
| dbg("%s: CAPREG offset %x cap_reg %x\n", |
| __FUNCTION__, ctrl->cap_base + CAPREG, cap_reg); |
| |
| if (((cap_reg & SLOT_IMPL) == 0) || |
| (((cap_reg & DEV_PORT_TYPE) != 0x0040) |
| && ((cap_reg & DEV_PORT_TYPE) != 0x0060))) { |
| dbg("%s : This is not a root port or the port is not " |
| "connected to a slot\n", __FUNCTION__); |
| goto abort_free_ctlr; |
| } |
| |
| rc = pciehp_readl(ctrl, SLOTCAP, &slot_cap); |
| if (rc) { |
| err("%s: Cannot read SLOTCAP register\n", __FUNCTION__); |
| goto abort_free_ctlr; |
| } |
| dbg("%s: SLOTCAP offset %x slot_cap %x\n", |
| __FUNCTION__, ctrl->cap_base + SLOTCAP, slot_cap); |
| |
| if (!(slot_cap & HP_CAP)) { |
| dbg("%s : This slot is not hot-plug capable\n", __FUNCTION__); |
| goto abort_free_ctlr; |
| } |
| /* For debugging purpose */ |
| rc = pciehp_readw(ctrl, SLOTSTATUS, &slot_status); |
| if (rc) { |
| err("%s: Cannot read SLOTSTATUS register\n", __FUNCTION__); |
| goto abort_free_ctlr; |
| } |
| dbg("%s: SLOTSTATUS offset %x slot_status %x\n", |
| __FUNCTION__, ctrl->cap_base + SLOTSTATUS, slot_status); |
| |
| rc = pciehp_readw(ctrl, SLOTCTRL, &slot_ctrl); |
| if (rc) { |
| err("%s: Cannot read SLOTCTRL register\n", __FUNCTION__); |
| goto abort_free_ctlr; |
| } |
| dbg("%s: SLOTCTRL offset %x slot_ctrl %x\n", |
| __FUNCTION__, ctrl->cap_base + SLOTCTRL, slot_ctrl); |
| |
| for (rc = 0; rc < DEVICE_COUNT_RESOURCE; rc++) |
| if (pci_resource_len(pdev, rc) > 0) |
| dbg("pci resource[%d] start=0x%llx(len=0x%llx)\n", rc, |
| (unsigned long long)pci_resource_start(pdev, rc), |
| (unsigned long long)pci_resource_len(pdev, rc)); |
| |
| info("HPC vendor_id %x device_id %x ss_vid %x ss_did %x\n", |
| pdev->vendor, pdev->device, |
| pdev->subsystem_vendor, pdev->subsystem_device); |
| |
| mutex_init(&ctrl->crit_sect); |
| mutex_init(&ctrl->ctrl_lock); |
| spin_lock_init(&ctrl->lock); |
| |
| /* setup wait queue */ |
| init_waitqueue_head(&ctrl->queue); |
| |
| /* return PCI Controller Info */ |
| ctrl->slot_device_offset = 0; |
| ctrl->num_slots = 1; |
| ctrl->first_slot = slot_cap >> 19; |
| ctrl->ctrlcap = slot_cap & 0x0000007f; |
| |
| /* Mask Hot-plug Interrupt Enable */ |
| rc = pciehp_readw(ctrl, SLOTCTRL, &temp_word); |
| if (rc) { |
| err("%s: Cannot read SLOTCTRL register\n", __FUNCTION__); |
| goto abort_free_ctlr; |
| } |
| |
| dbg("%s: SLOTCTRL %x value read %x\n", |
| __FUNCTION__, ctrl->cap_base + SLOTCTRL, temp_word); |
| temp_word = (temp_word & ~HP_INTR_ENABLE & ~CMD_CMPL_INTR_ENABLE) | |
| 0x00; |
| |
| rc = pciehp_writew(ctrl, SLOTCTRL, temp_word); |
| if (rc) { |
| err("%s: Cannot write to SLOTCTRL register\n", __FUNCTION__); |
| goto abort_free_ctlr; |
| } |
| |
| rc = pciehp_readw(ctrl, SLOTSTATUS, &slot_status); |
| if (rc) { |
| err("%s: Cannot read SLOTSTATUS register\n", __FUNCTION__); |
| goto abort_free_ctlr; |
| } |
| |
| temp_word = 0x1F; /* Clear all events */ |
| rc = pciehp_writew(ctrl, SLOTSTATUS, temp_word); |
| if (rc) { |
| err("%s: Cannot write to SLOTSTATUS register\n", __FUNCTION__); |
| goto abort_free_ctlr; |
| } |
| |
| if (pciehp_poll_mode) { |
| /* Install interrupt polling timer. Start with 10 sec delay */ |
| init_timer(&ctrl->poll_timer); |
| start_int_poll_timer(ctrl, 10); |
| } else { |
| /* Installs the interrupt handler */ |
| rc = request_irq(ctrl->pci_dev->irq, pcie_isr, IRQF_SHARED, |
| MY_NAME, (void *)ctrl); |
| dbg("%s: request_irq %d for hpc%d (returns %d)\n", |
| __FUNCTION__, ctrl->pci_dev->irq, |
| atomic_read(&pciehp_num_controllers), rc); |
| if (rc) { |
| err("Can't get irq %d for the hotplug controller\n", |
| ctrl->pci_dev->irq); |
| goto abort_free_ctlr; |
| } |
| } |
| dbg("pciehp ctrl b:d:f:irq=0x%x:%x:%x:%x\n", pdev->bus->number, |
| PCI_SLOT(pdev->devfn), PCI_FUNC(pdev->devfn), dev->irq); |
| |
| /* |
| * If this is the first controller to be initialized, |
| * initialize the pciehp work queue |
| */ |
| if (atomic_add_return(1, &pciehp_num_controllers) == 1) { |
| pciehp_wq = create_singlethread_workqueue("pciehpd"); |
| if (!pciehp_wq) { |
| rc = -ENOMEM; |
| goto abort_free_irq; |
| } |
| } |
| |
| rc = pciehp_readw(ctrl, SLOTCTRL, &temp_word); |
| if (rc) { |
| err("%s: Cannot read SLOTCTRL register\n", __FUNCTION__); |
| goto abort_free_irq; |
| } |
| |
| intr_enable = intr_enable | PRSN_DETECT_ENABLE; |
| |
| if (ATTN_BUTTN(slot_cap)) |
| intr_enable = intr_enable | ATTN_BUTTN_ENABLE; |
| |
| if (POWER_CTRL(slot_cap)) |
| intr_enable = intr_enable | PWR_FAULT_DETECT_ENABLE; |
| |
| if (MRL_SENS(slot_cap)) |
| intr_enable = intr_enable | MRL_DETECT_ENABLE; |
| |
| temp_word = (temp_word & ~intr_enable) | intr_enable; |
| |
| if (pciehp_poll_mode) { |
| temp_word = (temp_word & ~HP_INTR_ENABLE) | 0x0; |
| } else { |
| temp_word = (temp_word & ~HP_INTR_ENABLE) | HP_INTR_ENABLE; |
| } |
| |
| /* |
| * Unmask Hot-plug Interrupt Enable for the interrupt |
| * notification mechanism case. |
| */ |
| rc = pciehp_writew(ctrl, SLOTCTRL, temp_word); |
| if (rc) { |
| err("%s: Cannot write to SLOTCTRL register\n", __FUNCTION__); |
| goto abort_free_irq; |
| } |
| rc = pciehp_readw(ctrl, SLOTSTATUS, &slot_status); |
| if (rc) { |
| err("%s: Cannot read SLOTSTATUS register\n", __FUNCTION__); |
| goto abort_disable_intr; |
| } |
| |
| temp_word = 0x1F; /* Clear all events */ |
| rc = pciehp_writew(ctrl, SLOTSTATUS, temp_word); |
| if (rc) { |
| err("%s: Cannot write to SLOTSTATUS register\n", __FUNCTION__); |
| goto abort_disable_intr; |
| } |
| |
| if (pciehp_force) { |
| dbg("Bypassing BIOS check for pciehp use on %s\n", |
| pci_name(ctrl->pci_dev)); |
| } else { |
| rc = pciehp_get_hp_hw_control_from_firmware(ctrl->pci_dev); |
| if (rc) |
| goto abort_disable_intr; |
| } |
| |
| ctrl->hpc_ops = &pciehp_hpc_ops; |
| |
| return 0; |
| |
| /* We end up here for the many possible ways to fail this API. */ |
| abort_disable_intr: |
| rc = pciehp_readw(ctrl, SLOTCTRL, &temp_word); |
| if (!rc) { |
| temp_word &= ~(intr_enable | HP_INTR_ENABLE); |
| rc = pciehp_writew(ctrl, SLOTCTRL, temp_word); |
| } |
| if (rc) |
| err("%s : disabling interrupts failed\n", __FUNCTION__); |
| |
| abort_free_irq: |
| if (pciehp_poll_mode) |
| del_timer_sync(&ctrl->poll_timer); |
| else |
| free_irq(ctrl->pci_dev->irq, ctrl); |
| |
| abort_free_ctlr: |
| return -1; |
| } |