serial: Rework sh-sci for driver model.
sh-sci was turning in to an unmaintainable mess, especially with
regards to the port list. This cleans it up quite a bit, and
switches over to a platform device model where subtypes will
register their port list individually in their setup code.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
diff --git a/drivers/serial/sh-sci.c b/drivers/serial/sh-sci.c
index cbede06..f336ba6 100644
--- a/drivers/serial/sh-sci.c
+++ b/drivers/serial/sh-sci.c
@@ -3,7 +3,7 @@
*
* SuperH on-chip serial module support. (SCI with no FIFO / with FIFO)
*
- * Copyright (C) 2002, 2003, 2004 Paul Mundt
+ * Copyright (C) 2002 - 2006 Paul Mundt
*
* based off of the old drivers/char/sh-sci.c by:
*
@@ -20,10 +20,9 @@
#undef DEBUG
+#include <linux/config.h>
#include <linux/module.h>
#include <linux/errno.h>
-#include <linux/signal.h>
-#include <linux/sched.h>
#include <linux/timer.h>
#include <linux/interrupt.h>
#include <linux/tty.h>
@@ -32,34 +31,25 @@
#include <linux/major.h>
#include <linux/string.h>
#include <linux/sysrq.h>
-#include <linux/fcntl.h>
-#include <linux/ptrace.h>
#include <linux/ioport.h>
#include <linux/mm.h>
-#include <linux/slab.h>
#include <linux/init.h>
#include <linux/delay.h>
#include <linux/console.h>
-#include <linux/bitops.h>
-#include <linux/generic_serial.h>
+#include <linux/platform_device.h>
#ifdef CONFIG_CPU_FREQ
#include <linux/notifier.h>
#include <linux/cpufreq.h>
#endif
-#include <asm/system.h>
-#include <asm/io.h>
-#include <asm/irq.h>
-#include <asm/uaccess.h>
-
#if defined(CONFIG_SUPERH) && !defined(CONFIG_SUPERH64)
#include <asm/clock.h>
+#include <asm/sh_bios.h>
+#include <asm/kgdb.h>
#endif
-#ifdef CONFIG_SH_STANDARD_BIOS
-#include <asm/sh_bios.h>
-#endif
+#include <asm/sci.h>
#if defined(CONFIG_SERIAL_SH_SCI_CONSOLE) && defined(CONFIG_MAGIC_SYSRQ)
#define SUPPORT_SYSRQ
@@ -67,36 +57,51 @@
#include "sh-sci.h"
-#ifdef CONFIG_SH_KGDB
-#include <asm/kgdb.h>
+struct sci_port {
+ struct uart_port port;
-static int kgdb_get_char(struct sci_port *port);
-static void kgdb_put_char(struct sci_port *port, char c);
-static void kgdb_handle_error(struct sci_port *port);
+ /* Port type */
+ unsigned int type;
+
+ /* Port IRQs: ERI, RXI, TXI, BRI (optional) */
+ unsigned int irqs[SCIx_NR_IRQS];
+
+ /* Port pin configuration */
+ void (*init_pins)(struct uart_port *port,
+ unsigned int cflag);
+
+ /* Port enable callback */
+ void (*enable)(struct uart_port *port);
+
+ /* Port disable callback */
+ void (*disable)(struct uart_port *port);
+
+ /* Break timer */
+ struct timer_list break_timer;
+ int break_flag;
+};
+
+#ifdef CONFIG_SH_KGDB
static struct sci_port *kgdb_sci_port;
-#endif /* CONFIG_SH_KGDB */
+#endif
#ifdef CONFIG_SERIAL_SH_SCI_CONSOLE
-static struct sci_port *serial_console_port = 0;
-#endif /* CONFIG_SERIAL_SH_SCI_CONSOLE */
+static struct sci_port *serial_console_port;
+#endif
/* Function prototypes */
static void sci_stop_tx(struct uart_port *port);
-static void sci_start_tx(struct uart_port *port);
-static void sci_start_rx(struct uart_port *port, unsigned int tty_start);
-static void sci_stop_rx(struct uart_port *port);
-static int sci_request_irq(struct sci_port *port);
-static void sci_free_irq(struct sci_port *port);
-static struct sci_port sci_ports[];
+#define SCI_NPORTS CONFIG_SERIAL_SH_SCI_NR_UARTS
+
+static struct sci_port sci_ports[SCI_NPORTS];
static struct uart_driver sci_uart_driver;
-#define SCI_NPORTS sci_uart_driver.nr
-
-#if defined(CONFIG_SH_STANDARD_BIOS) || defined(CONFIG_SH_KGDB)
-
-static void handle_error(struct uart_port *port)
-{ /* Clear error flags */
+#if defined(CONFIG_SERIAL_SH_SCI_CONSOLE) && \
+ defined(CONFIG_SH_STANDARD_BIOS) || defined(CONFIG_SH_KGDB)
+static inline void handle_error(struct uart_port *port)
+{
+ /* Clear error flags */
sci_out(port, SCxSR, SCxSR_ERROR_CLEAR(port));
}
@@ -106,8 +111,8 @@
unsigned short status;
int c;
- local_irq_save(flags);
- do {
+ spin_lock_irqsave(&port->lock, flags);
+ do {
status = sci_in(port, SCxSR);
if (status & SCxSR_ERRORS(port)) {
handle_error(port);
@@ -117,38 +122,19 @@
c = sci_in(port, SCxRDR);
sci_in(port, SCxSR); /* Dummy read */
sci_out(port, SCxSR, SCxSR_RDxF_CLEAR(port));
- local_irq_restore(flags);
+ spin_unlock_irqrestore(&port->lock, flags);
return c;
}
-
-/* Taken from sh-stub.c of GDB 4.18 */
-static const char hexchars[] = "0123456789abcdef";
-
-static __inline__ char highhex(int x)
-{
- return hexchars[(x >> 4) & 0xf];
-}
-
-static __inline__ char lowhex(int x)
-{
- return hexchars[x & 0xf];
-}
-
#endif /* CONFIG_SH_STANDARD_BIOS || CONFIG_SH_KGDB */
-/*
- * Send the packet in buffer. The host gets one chance to read it.
- * This routine does not wait for a positive acknowledge.
- */
-
-#ifdef CONFIG_SERIAL_SH_SCI_CONSOLE
+#if defined(CONFIG_SERIAL_SH_SCI_CONSOLE) || defined(CONFIG_SH_KGDB)
static void put_char(struct uart_port *port, char c)
{
unsigned long flags;
unsigned short status;
- local_irq_save(flags);
+ spin_lock_irqsave(&port->lock, flags);
do {
status = sci_in(port, SCxSR);
@@ -158,9 +144,11 @@
sci_in(port, SCxSR); /* Dummy read */
sci_out(port, SCxSR, SCxSR_TDxE_CLEAR(port));
- local_irq_restore(flags);
+ spin_unlock_irqrestore(&port->lock, flags);
}
+#endif
+#ifdef CONFIG_SERIAL_SH_SCI_CONSOLE
static void put_string(struct sci_port *sci_port, const char *buffer, int count)
{
struct uart_port *port = &sci_port->port;
@@ -213,96 +201,28 @@
}
#endif /* CONFIG_SERIAL_SH_SCI_CONSOLE */
-
#ifdef CONFIG_SH_KGDB
-
-/* Is the SCI ready, ie is there a char waiting? */
-static int kgdb_is_char_ready(struct sci_port *port)
-{
- unsigned short status = sci_in(port, SCxSR);
-
- if (status & (SCxSR_ERRORS(port) | SCxSR_BRK(port)))
- kgdb_handle_error(port);
-
- return (status & SCxSR_RDxF(port));
-}
-
-/* Write a char */
-static void kgdb_put_char(struct sci_port *port, char c)
-{
- unsigned short status;
-
- do
- status = sci_in(port, SCxSR);
- while (!(status & SCxSR_TDxE(port)));
-
- sci_out(port, SCxTDR, c);
- sci_in(port, SCxSR); /* Dummy read */
- sci_out(port, SCxSR, SCxSR_TDxE_CLEAR(port));
-}
-
-/* Get a char if there is one, else ret -1 */
-static int kgdb_get_char(struct sci_port *port)
+static int kgdb_sci_getchar(void)
{
int c;
- if (kgdb_is_char_ready(port) == 0)
- c = -1;
- else {
- c = sci_in(port, SCxRDR);
- sci_in(port, SCxSR); /* Dummy read */
- sci_out(port, SCxSR, SCxSR_RDxF_CLEAR(port));
- }
-
- return c;
-}
-
-/* Called from kgdbstub.c to get a character, i.e. is blocking */
-static int kgdb_sci_getchar(void)
-{
- volatile int c;
-
/* Keep trying to read a character, this could be neater */
- while ((c = kgdb_get_char(kgdb_sci_port)) < 0);
+ while ((c = get_char(kgdb_sci_port)) < 0)
+ cpu_relax();
return c;
}
-/* Called from kgdbstub.c to put a character, just a wrapper */
-static void kgdb_sci_putchar(int c)
+static inline void kgdb_sci_putchar(int c)
{
-
- kgdb_put_char(kgdb_sci_port, c);
+ put_char(kgdb_sci_port, c);
}
-
-/* Clear any errors on the SCI */
-static void kgdb_handle_error(struct sci_port *port)
-{
- sci_out(port, SCxSR, SCxSR_ERROR_CLEAR(port)); /* Clear error flags */
-}
-
-/* Breakpoint if there's a break sent on the serial port */
-static void kgdb_break_interrupt(int irq, void *ptr, struct pt_regs *regs)
-{
- struct sci_port *port = ptr;
- unsigned short status = sci_in(port, SCxSR);
-
- if (status & SCxSR_BRK(port)) {
-
- /* Break into the debugger if a break is detected */
- BREAKPOINT();
-
- /* Clear */
- sci_out(port, SCxSR, SCxSR_BREAK_CLEAR(port));
- }
-}
-
#endif /* CONFIG_SH_KGDB */
#if defined(__H8300S__)
enum { sci_disable, sci_enable };
-static void h8300_sci_enable(struct uart_port* port, unsigned int ctrl)
+static void h8300_sci_config(struct uart_port* port, unsigned int ctrl)
{
volatile unsigned char *mstpcrl=(volatile unsigned char *)MSTPCRL;
int ch = (port->mapbase - SMR0) >> 3;
@@ -314,32 +234,66 @@
*mstpcrl &= ~mask;
}
}
+
+static inline void h8300_sci_enable(struct uart_port *port)
+{
+ h8300_sci_config(port, sci_enable);
+}
+
+static inline void h8300_sci_disable(struct uart_port *port)
+{
+ h8300_sci_config(port, sci_disable);
+}
#endif
-#if defined(SCI_ONLY) || defined(SCI_AND_SCIF)
-#if defined(__H8300H__) || defined(__H8300S__)
+#if defined(SCI_ONLY) || defined(SCI_AND_SCIF) && \
+ defined(__H8300H__) || defined(__H8300S__)
static void sci_init_pins_sci(struct uart_port* port, unsigned int cflag)
{
int ch = (port->mapbase - SMR0) >> 3;
/* set DDR regs */
- H8300_GPIO_DDR(h8300_sci_pins[ch].port,h8300_sci_pins[ch].rx,H8300_GPIO_INPUT);
- H8300_GPIO_DDR(h8300_sci_pins[ch].port,h8300_sci_pins[ch].tx,H8300_GPIO_OUTPUT);
+ H8300_GPIO_DDR(h8300_sci_pins[ch].port,
+ h8300_sci_pins[ch].rx,
+ H8300_GPIO_INPUT);
+ H8300_GPIO_DDR(h8300_sci_pins[ch].port,
+ h8300_sci_pins[ch].tx,
+ H8300_GPIO_OUTPUT);
+
/* tx mark output*/
H8300_SCI_DR(ch) |= h8300_sci_pins[ch].tx;
}
+#else
+#define sci_init_pins_sci NULL
#endif
+
+#if defined(CONFIG_CPU_SUBTYPE_SH7707) || defined(CONFIG_CPU_SUBTYPE_SH7709)
+static void sci_init_pins_irda(struct uart_port *port, unsigned int cflag)
+{
+ unsigned int fcr_val = 0;
+
+ if (cflag & CRTSCTS)
+ fcr_val |= SCFCR_MCE;
+
+ sci_out(port, SCFCR, fcr_val);
+}
+#else
+#define sci_init_pins_irda NULL
+#endif
+
+#ifdef SCI_ONLY
+#define sci_init_pins_scif NULL
#endif
#if defined(SCIF_ONLY) || defined(SCI_AND_SCIF)
-#if defined(CONFIG_CPU_SUBTYPE_SH7300)
+#if defined(CONFIG_CPU_SUBTYPE_SH7300) || defined(CONFIG_CPU_SUBTYPE_SH7710)
/* SH7300 doesn't use RTS/CTS */
static void sci_init_pins_scif(struct uart_port *port, unsigned int cflag)
{
sci_out(port, SCFCR, 0);
}
#elif defined(CONFIG_CPU_SH3)
-/* For SH7705, SH7707, SH7709, SH7709A, SH7729 */
+/* For SH7705, SH7706, SH7707, SH7709, SH7709A, SH7729 */
static void sci_init_pins_scif(struct uart_port *port, unsigned int cflag)
{
unsigned int fcr_val = 0;
@@ -366,20 +320,7 @@
sci_out(port, SCFCR, fcr_val);
}
-
-#if defined(CONFIG_CPU_SUBTYPE_SH7707) || defined(CONFIG_CPU_SUBTYPE_SH7709)
-static void sci_init_pins_irda(struct uart_port *port, unsigned int cflag)
-{
- unsigned int fcr_val = 0;
-
- if (cflag & CRTSCTS)
- fcr_val |= SCFCR_MCE;
-
- sci_out(port, SCFCR, fcr_val);
-}
-#endif
#else
-
/* For SH7750 */
static void sci_init_pins_scif(struct uart_port *port, unsigned int cflag)
{
@@ -388,7 +329,9 @@
if (cflag & CRTSCTS) {
fcr_val |= SCFCR_MCE;
} else {
-#ifdef CONFIG_CPU_SUBTYPE_SH7780
+#ifdef CONFIG_CPU_SUBTYPE_SH7343
+ /* Nothing */
+#elif defined(CONFIG_CPU_SUBTYPE_SH7780)
ctrl_outw(0x0080, SCSPTR0); /* Set RTS = 1 */
#else
ctrl_outw(0x0080, SCSPTR2); /* Set RTS = 1 */
@@ -396,10 +339,41 @@
}
sci_out(port, SCFCR, fcr_val);
}
+#endif
+#if defined(CONFIG_CPU_SUBTYPE_SH7760) || defined(CONFIG_CPU_SUBTYPE_SH7780)
+static inline int scif_txroom(struct uart_port *port)
+{
+ return SCIF_TXROOM_MAX - (sci_in(port, SCTFDR) & 0x7f);
+}
+
+static inline int scif_rxroom(struct uart_port *port)
+{
+ return sci_in(port, SCRFDR) & 0x7f;
+}
+#else
+static inline int scif_txroom(struct uart_port *port)
+{
+ return SCIF_TXROOM_MAX - (sci_in(port, SCFDR) >> 8);
+}
+
+static inline int scif_rxroom(struct uart_port *port)
+{
+ return sci_in(port, SCFDR) & SCIF_RFDC_MASK;
+}
#endif
#endif /* SCIF_ONLY || SCI_AND_SCIF */
+static inline int sci_txroom(struct uart_port *port)
+{
+ return ((sci_in(port, SCxSR) & SCI_TDRE) != 0);
+}
+
+static inline int sci_rxroom(struct uart_port *port)
+{
+ return ((sci_in(port, SCxSR) & SCxSR_RDxF(port)) != 0);
+}
+
/* ********************************************************************** *
* the interrupt related routines *
* ********************************************************************** */
@@ -408,14 +382,12 @@
{
struct circ_buf *xmit = &port->info->xmit;
unsigned int stopped = uart_tx_stopped(port);
- unsigned long flags;
unsigned short status;
unsigned short ctrl;
- int count, txroom;
+ int count;
status = sci_in(port, SCxSR);
if (!(status & SCxSR_TDxE(port))) {
- local_irq_save(flags);
ctrl = sci_in(port, SCSCR);
if (uart_circ_empty(xmit)) {
ctrl &= ~SCI_CTRL_FLAGS_TIE;
@@ -423,25 +395,15 @@
ctrl |= SCI_CTRL_FLAGS_TIE;
}
sci_out(port, SCSCR, ctrl);
- local_irq_restore(flags);
return;
}
-#if !defined(SCI_ONLY)
- if (port->type == PORT_SCIF) {
-#if defined(CONFIG_CPU_SUBTYPE_SH7760) || defined(CONFIG_CPU_SUBTYPE_SH7780)
- txroom = SCIF_TXROOM_MAX - (sci_in(port, SCTFDR) & 0x7f);
-#else
- txroom = SCIF_TXROOM_MAX - (sci_in(port, SCFDR)>>8);
+#ifndef SCI_ONLY
+ if (port->type == PORT_SCIF)
+ count = scif_txroom(port);
+ else
#endif
- } else {
- txroom = (sci_in(port, SCxSR) & SCI_TDRE)?1:0;
- }
-#else
- txroom = (sci_in(port, SCxSR) & SCI_TDRE)?1:0;
-#endif
-
- count = txroom;
+ count = sci_txroom(port);
do {
unsigned char c;
@@ -468,7 +430,6 @@
if (uart_circ_empty(xmit)) {
sci_stop_tx(port);
} else {
- local_irq_save(flags);
ctrl = sci_in(port, SCSCR);
#if !defined(SCI_ONLY)
@@ -480,7 +441,6 @@
ctrl |= SCI_CTRL_FLAGS_TIE;
sci_out(port, SCSCR, ctrl);
- local_irq_restore(flags);
}
}
@@ -490,6 +450,7 @@
static inline void sci_receive_chars(struct uart_port *port,
struct pt_regs *regs)
{
+ struct sci_port *sci_port = (struct sci_port *)port;
struct tty_struct *tty = port->info->tty;
int i, count, copied = 0;
unsigned short status;
@@ -501,18 +462,11 @@
while (1) {
#if !defined(SCI_ONLY)
- if (port->type == PORT_SCIF) {
-#if defined(CONFIG_CPU_SUBTYPE_SH7760) || defined(CONFIG_CPU_SUBTYPE_SH7780)
- count = sci_in(port, SCRFDR) & 0x7f;
-#else
- count = sci_in(port, SCFDR)&SCIF_RFDC_MASK ;
+ if (port->type == PORT_SCIF)
+ count = scif_rxroom(port);
+ else
#endif
- } else {
- count = (sci_in(port, SCxSR)&SCxSR_RDxF(port))?1:0;
- }
-#else
- count = (sci_in(port, SCxSR)&SCxSR_RDxF(port))?1:0;
-#endif
+ count = sci_rxroom(port);
/* Don't copy more bytes than there is room for in the buffer */
count = tty_buffer_request_room(tty, count);
@@ -523,11 +477,10 @@
if (port->type == PORT_SCI) {
char c = sci_in(port, SCxRDR);
- if(((struct sci_port *)port)->break_flag
- || uart_handle_sysrq_char(port, c, regs)) {
+ if (uart_handle_sysrq_char(port, c, regs) || sci_port->break_flag)
count = 0;
- } else {
- tty_insert_flip_char(tty, c, TTY_NORMAL);
+ else {
+ tty_insert_flip_char(tty, c, TTY_NORMAL);
}
} else {
for (i=0; i<count; i++) {
@@ -535,15 +488,17 @@
status = sci_in(port, SCxSR);
#if defined(CONFIG_CPU_SH3)
/* Skip "chars" during break */
- if (((struct sci_port *)port)->break_flag) {
+ if (sci_port->break_flag) {
if ((c == 0) &&
(status & SCxSR_FER(port))) {
count--; i--;
continue;
}
+
/* Nonzero => end-of-break */
pr_debug("scif: debounce<%02x>\n", c);
- ((struct sci_port *)port)->break_flag = 0;
+ sci_port->break_flag = 0;
+
if (STEPFN(c)) {
count--; i--;
continue;
@@ -600,15 +555,17 @@
/* Ensure that two consecutive samples find the break over. */
static void sci_break_timer(unsigned long data)
{
- struct sci_port * port = (struct sci_port *)data;
- if(sci_rxd_in(&port->port) == 0) {
+ struct sci_port *port = (struct sci_port *)data;
+
+ if (sci_rxd_in(&port->port) == 0) {
port->break_flag = 1;
- sci_schedule_break_timer(port);
- } else if(port->break_flag == 1){
+ sci_schedule_break_timer(port);
+ } else if (port->break_flag == 1) {
/* break is over. */
port->break_flag = 2;
- sci_schedule_break_timer(port);
- } else port->break_flag = 0;
+ sci_schedule_break_timer(port);
+ } else
+ port->break_flag = 0;
}
static inline int sci_handle_errors(struct uart_port *port)
@@ -617,40 +574,41 @@
unsigned short status = sci_in(port, SCxSR);
struct tty_struct *tty = port->info->tty;
- if (status&SCxSR_ORER(port)) {
+ if (status & SCxSR_ORER(port)) {
/* overrun error */
- if(tty_insert_flip_char(tty, 0, TTY_OVERRUN))
+ if (tty_insert_flip_char(tty, 0, TTY_OVERRUN))
copied++;
pr_debug("sci: overrun error\n");
}
- if (status&SCxSR_FER(port)) {
+ if (status & SCxSR_FER(port)) {
if (sci_rxd_in(port) == 0) {
/* Notify of BREAK */
- struct sci_port * sci_port = (struct sci_port *)port;
- if(!sci_port->break_flag) {
- sci_port->break_flag = 1;
- sci_schedule_break_timer((struct sci_port *)port);
+ struct sci_port *sci_port = (struct sci_port *)port;
+
+ if (!sci_port->break_flag) {
+ sci_port->break_flag = 1;
+ sci_schedule_break_timer(sci_port);
+
/* Do sysrq handling. */
- if(uart_handle_break(port))
+ if (uart_handle_break(port))
return 0;
pr_debug("sci: BREAK detected\n");
- if(tty_insert_flip_char(tty, 0, TTY_BREAK))
+ if (tty_insert_flip_char(tty, 0, TTY_BREAK))
copied++;
}
- }
- else {
+ } else {
/* frame error */
- if(tty_insert_flip_char(tty, 0, TTY_FRAME))
+ if (tty_insert_flip_char(tty, 0, TTY_FRAME))
copied++;
pr_debug("sci: frame error\n");
}
}
- if (status&SCxSR_PER(port)) {
- if(tty_insert_flip_char(tty, 0, TTY_PARITY))
- copied++;
+ if (status & SCxSR_PER(port)) {
/* parity error */
+ if (tty_insert_flip_char(tty, 0, TTY_PARITY))
+ copied++;
pr_debug("sci: parity error\n");
}
@@ -673,7 +631,7 @@
s->break_flag = 1;
#endif
/* Notify of BREAK */
- if(tty_insert_flip_char(tty, 0, TTY_BREAK))
+ if (tty_insert_flip_char(tty, 0, TTY_BREAK))
copied++;
pr_debug("sci: BREAK detected\n");
}
@@ -682,7 +640,7 @@
/* XXX: Handle SCIF overrun error */
if (port->type == PORT_SCIF && (sci_in(port, SCLSR) & SCIF_ORER) != 0) {
sci_out(port, SCLSR, 0);
- if(tty_insert_flip_char(tty, 0, TTY_OVERRUN)) {
+ if (tty_insert_flip_char(tty, 0, TTY_OVERRUN)) {
copied++;
pr_debug("sci: overrun error\n");
}
@@ -691,13 +649,12 @@
if (copied)
tty_flip_buffer_push(tty);
+
return copied;
}
-static irqreturn_t sci_rx_interrupt(int irq, void *ptr, struct pt_regs *regs)
+static irqreturn_t sci_rx_interrupt(int irq, void *port, struct pt_regs *regs)
{
- struct uart_port *port = ptr;
-
/* I think sci_receive_chars has to be called irrespective
* of whether the I_IXOFF is set, otherwise, how is the interrupt
* to be disabled?
@@ -711,7 +668,9 @@
{
struct uart_port *port = ptr;
+ spin_lock_irq(&port->lock);
sci_transmit_chars(port);
+ spin_unlock_irq(&port->lock);
return IRQ_HANDLED;
}
@@ -755,6 +714,12 @@
/* Handle BREAKs */
sci_handle_breaks(port);
+
+#ifdef CONFIG_SH_KGDB
+ /* Break into the debugger if a break is detected */
+ BREAKPOINT();
+#endif
+
sci_out(port, SCxSR, SCxSR_BREAK_CLEAR(port));
return IRQ_HANDLED;
@@ -769,16 +734,16 @@
scr_status = sci_in(port,SCSCR);
/* Tx Interrupt */
- if ((ssr_status&0x0020) && (scr_status&0x0080))
+ if ((ssr_status & 0x0020) && (scr_status & 0x0080))
sci_tx_interrupt(irq, ptr, regs);
/* Rx Interrupt */
- if ((ssr_status&0x0002) && (scr_status&0x0040))
+ if ((ssr_status & 0x0002) && (scr_status & 0x0040))
sci_rx_interrupt(irq, ptr, regs);
/* Error Interrupt */
- if ((ssr_status&0x0080) && (scr_status&0x0400))
+ if ((ssr_status & 0x0080) && (scr_status & 0x0400))
sci_er_interrupt(irq, ptr, regs);
/* Break Interrupt */
- if ((ssr_status&0x0010) && (scr_status&0x0200))
+ if ((ssr_status & 0x0010) && (scr_status & 0x0200))
sci_br_interrupt(irq, ptr, regs);
return IRQ_HANDLED;
@@ -789,7 +754,8 @@
* Here we define a transistion notifier so that we can update all of our
* ports' baud rate when the peripheral clock changes.
*/
-static int sci_notifier(struct notifier_block *self, unsigned long phase, void *p)
+static int sci_notifier(struct notifier_block *self,
+ unsigned long phase, void *p)
{
struct cpufreq_freqs *freqs = p;
int i;
@@ -816,8 +782,9 @@
clk_put(clk);
}
- printk("%s: got a postchange notification for cpu %d (old %d, new %d)\n",
- __FUNCTION__, freqs->cpu, freqs->old, freqs->new);
+ printk(KERN_INFO "%s: got a postchange notification "
+ "for cpu %d (old %d, new %d)\n",
+ __FUNCTION__, freqs->cpu, freqs->old, freqs->new);
}
return NOTIFY_OK;
@@ -841,8 +808,9 @@
printk(KERN_ERR "sci: Cannot allocate irq.(IRQ=0)\n");
return -ENODEV;
}
- if (request_irq(port->irqs[0], sci_mpxed_interrupt, IRQF_DISABLED,
- "sci", port)) {
+
+ if (request_irq(port->irqs[0], sci_mpxed_interrupt,
+ SA_INTERRUPT, "sci", port)) {
printk(KERN_ERR "sci: Cannot allocate irq.\n");
return -ENODEV;
}
@@ -850,8 +818,8 @@
for (i = 0; i < ARRAY_SIZE(handlers); i++) {
if (!port->irqs[i])
continue;
- if (request_irq(port->irqs[i], handlers[i], IRQF_DISABLED,
- desc[i], port)) {
+ if (request_irq(port->irqs[i], handlers[i],
+ SA_INTERRUPT, desc[i], port)) {
printk(KERN_ERR "sci: Cannot allocate irq.\n");
return -ENODEV;
}
@@ -903,50 +871,42 @@
static void sci_start_tx(struct uart_port *port)
{
- struct sci_port *s = &sci_ports[port->line];
+ unsigned short ctrl;
- disable_irq(s->irqs[SCIx_TXI_IRQ]);
- sci_transmit_chars(port);
- enable_irq(s->irqs[SCIx_TXI_IRQ]);
+ /* Set TIE (Transmit Interrupt Enable) bit in SCSCR */
+ ctrl = sci_in(port, SCSCR);
+ ctrl |= SCI_CTRL_FLAGS_TIE;
+ sci_out(port, SCSCR, ctrl);
}
static void sci_stop_tx(struct uart_port *port)
{
- unsigned long flags;
unsigned short ctrl;
/* Clear TIE (Transmit Interrupt Enable) bit in SCSCR */
- local_irq_save(flags);
ctrl = sci_in(port, SCSCR);
ctrl &= ~SCI_CTRL_FLAGS_TIE;
sci_out(port, SCSCR, ctrl);
- local_irq_restore(flags);
}
static void sci_start_rx(struct uart_port *port, unsigned int tty_start)
{
- unsigned long flags;
unsigned short ctrl;
/* Set RIE (Receive Interrupt Enable) bit in SCSCR */
- local_irq_save(flags);
ctrl = sci_in(port, SCSCR);
ctrl |= SCI_CTRL_FLAGS_RIE | SCI_CTRL_FLAGS_REIE;
sci_out(port, SCSCR, ctrl);
- local_irq_restore(flags);
}
static void sci_stop_rx(struct uart_port *port)
{
- unsigned long flags;
unsigned short ctrl;
/* Clear RIE (Receive Interrupt Enable) bit in SCSCR */
- local_irq_save(flags);
ctrl = sci_in(port, SCSCR);
ctrl &= ~(SCI_CTRL_FLAGS_RIE | SCI_CTRL_FLAGS_REIE);
sci_out(port, SCSCR, ctrl);
- local_irq_restore(flags);
}
static void sci_enable_ms(struct uart_port *port)
@@ -963,9 +923,8 @@
{
struct sci_port *s = &sci_ports[port->line];
-#if defined(__H8300S__)
- h8300_sci_enable(port, sci_enable);
-#endif
+ if (s->enable)
+ s->enable(port);
sci_request_irq(s);
sci_start_tx(port);
@@ -982,9 +941,8 @@
sci_stop_tx(port);
sci_free_irq(s);
-#if defined(__H8300S__)
- h8300_sci_enable(port, sci_disable);
-#endif
+ if (s->disable)
+ s->disable(port);
}
static void sci_set_termios(struct uart_port *port, struct termios *termios,
@@ -997,34 +955,6 @@
baud = uart_get_baud_rate(port, termios, old, 0, port->uartclk/16);
- spin_lock_irqsave(&port->lock, flags);
-
- do {
- status = sci_in(port, SCxSR);
- } while (!(status & SCxSR_TEND(port)));
-
- sci_out(port, SCSCR, 0x00); /* TE=0, RE=0, CKE1=0 */
-
-#if !defined(SCI_ONLY)
- if (port->type == PORT_SCIF) {
- sci_out(port, SCFCR, SCFCR_RFRST | SCFCR_TFRST);
- }
-#endif
-
- smr_val = sci_in(port, SCSMR) & 3;
- if ((termios->c_cflag & CSIZE) == CS7)
- smr_val |= 0x40;
- if (termios->c_cflag & PARENB)
- smr_val |= 0x20;
- if (termios->c_cflag & PARODD)
- smr_val |= 0x30;
- if (termios->c_cflag & CSTOPB)
- smr_val |= 0x08;
-
- uart_update_timeout(port, termios->c_cflag, baud);
-
- sci_out(port, SCSMR, smr_val);
-
switch (baud) {
case 0:
t = -1;
@@ -1042,6 +972,33 @@
break;
}
+ spin_lock_irqsave(&port->lock, flags);
+
+ do {
+ status = sci_in(port, SCxSR);
+ } while (!(status & SCxSR_TEND(port)));
+
+ sci_out(port, SCSCR, 0x00); /* TE=0, RE=0, CKE1=0 */
+
+#if !defined(SCI_ONLY)
+ if (port->type == PORT_SCIF)
+ sci_out(port, SCFCR, SCFCR_RFRST | SCFCR_TFRST);
+#endif
+
+ smr_val = sci_in(port, SCSMR) & 3;
+ if ((termios->c_cflag & CSIZE) == CS7)
+ smr_val |= 0x40;
+ if (termios->c_cflag & PARENB)
+ smr_val |= 0x20;
+ if (termios->c_cflag & PARODD)
+ smr_val |= 0x30;
+ if (termios->c_cflag & CSTOPB)
+ smr_val |= 0x08;
+
+ uart_update_timeout(port, termios->c_cflag, baud);
+
+ sci_out(port, SCSMR, smr_val);
+
if (t > 0) {
if(t >= 256) {
sci_out(port, SCSMR, (sci_in(port, SCSMR) & ~3) | 1);
@@ -1092,11 +1049,23 @@
port->type = s->type;
+ switch (port->type) {
+ case PORT_SCI:
+ s->init_pins = sci_init_pins_sci;
+ break;
+ case PORT_SCIF:
+ s->init_pins = sci_init_pins_scif;
+ break;
+ case PORT_IRDA:
+ s->init_pins = sci_init_pins_irda;
+ break;
+ }
+
#if defined(CONFIG_CPU_SUBTYPE_SH5_101) || defined(CONFIG_CPU_SUBTYPE_SH5_103)
if (port->mapbase == 0)
port->mapbase = onchip_remap(SCIF_ADDR_SH5, 1024, "SCIF");
- port->membase = (void *)port->mapbase;
+ port->membase = (void __iomem *)port->mapbase;
#endif
}
@@ -1132,412 +1101,61 @@
.verify_port = sci_verify_port,
};
-static struct sci_port sci_ports[] = {
-#if defined(CONFIG_CPU_SUBTYPE_SH7708)
- {
- .port = {
- .membase = (void *)0xfffffe80,
- .mapbase = 0xfffffe80,
- .iotype = UPIO_MEM,
- .irq = 25,
- .ops = &sci_uart_ops,
- .flags = UPF_BOOT_AUTOCONF,
- .line = 0,
- },
- .type = PORT_SCI,
- .irqs = SCI_IRQS,
- },
-#elif defined(CONFIG_CPU_SUBTYPE_SH7705)
- {
- .port = {
- .membase = (void *)SCIF0,
- .mapbase = SCIF0,
- .iotype = UPIO_MEM,
- .irq = 55,
- .ops = &sci_uart_ops,
- .flags = UPF_BOOT_AUTOCONF,
- .line = 0,
- },
- .type = PORT_SCIF,
- .irqs = SH3_IRDA_IRQS,
- .init_pins = sci_init_pins_scif,
- },
- {
- .port = {
- .membase = (void *)SCIF2,
- .mapbase = SCIF2,
- .iotype = UPIO_MEM,
- .irq = 59,
- .ops = &sci_uart_ops,
- .flags = UPF_BOOT_AUTOCONF,
- .line = 1,
- },
- .type = PORT_SCIF,
- .irqs = SH3_SCIF_IRQS,
- .init_pins = sci_init_pins_scif,
- }
-#elif defined(CONFIG_CPU_SUBTYPE_SH7707) || defined(CONFIG_CPU_SUBTYPE_SH7709)
- {
- .port = {
- .membase = (void *)0xfffffe80,
- .mapbase = 0xfffffe80,
- .iotype = UPIO_MEM,
- .irq = 25,
- .ops = &sci_uart_ops,
- .flags = UPF_BOOT_AUTOCONF,
- .line = 0,
- },
- .type = PORT_SCI,
- .irqs = SCI_IRQS,
- },
- {
- .port = {
- .membase = (void *)0xa4000150,
- .mapbase = 0xa4000150,
- .iotype = UPIO_MEM,
- .irq = 59,
- .ops = &sci_uart_ops,
- .flags = UPF_BOOT_AUTOCONF,
- .line = 1,
- },
- .type = PORT_SCIF,
- .irqs = SH3_SCIF_IRQS,
- .init_pins = sci_init_pins_scif,
- },
- {
- .port = {
- .membase = (void *)0xa4000140,
- .mapbase = 0xa4000140,
- .iotype = UPIO_MEM,
- .irq = 55,
- .ops = &sci_uart_ops,
- .flags = UPF_BOOT_AUTOCONF,
- .line = 2,
- },
- .type = PORT_IRDA,
- .irqs = SH3_IRDA_IRQS,
- .init_pins = sci_init_pins_irda,
- }
-#elif defined(CONFIG_CPU_SUBTYPE_SH7300)
- {
- .port = {
- .membase = (void *)0xA4430000,
- .mapbase = 0xA4430000,
- .iotype = UPIO_MEM,
- .irq = 25,
- .ops = &sci_uart_ops,
- .flags = UPF_BOOT_AUTOCONF,
- .line = 0,
- },
- .type = PORT_SCIF,
- .irqs = SH7300_SCIF0_IRQS,
- .init_pins = sci_init_pins_scif,
- },
-#elif defined(CONFIG_CPU_SUBTYPE_SH73180)
- {
- .port = {
- .membase = (void *)0xffe00000,
- .mapbase = 0xffe00000,
- .iotype = UPIO_MEM,
- .irq = 25,
- .ops = &sci_uart_ops,
- .flags = UPF_BOOT_AUTOCONF,
- .line = 0,
- },
- .type = PORT_SCIF,
- .irqs = SH73180_SCIF_IRQS,
- .init_pins = sci_init_pins_scif,
- },
-#elif defined(CONFIG_CPU_SUBTYPE_SH4_202)
- {
- .port = {
- .membase = (void *)0xffe80000,
- .mapbase = 0xffe80000,
- .iotype = UPIO_MEM,
- .irq = 43,
- .ops = &sci_uart_ops,
- .flags = UPF_BOOT_AUTOCONF,
- .line = 0,
- },
- .type = PORT_SCIF,
- .irqs = SH4_SCIF_IRQS,
- .init_pins = sci_init_pins_scif,
- },
-#elif defined(CONFIG_CPU_SUBTYPE_SH7750) || defined(CONFIG_CPU_SUBTYPE_SH7751)
- {
- .port = {
- .membase = (void *)0xffe00000,
- .mapbase = 0xffe00000,
- .iotype = UPIO_MEM,
- .irq = 25,
- .ops = &sci_uart_ops,
- .flags = UPF_BOOT_AUTOCONF,
- .line = 0,
- },
- .type = PORT_SCI,
- .irqs = SCI_IRQS,
- },
- {
- .port = {
- .membase = (void *)0xffe80000,
- .mapbase = 0xffe80000,
- .iotype = UPIO_MEM,
- .irq = 43,
- .ops = &sci_uart_ops,
- .flags = UPF_BOOT_AUTOCONF,
- .line = 1,
- },
- .type = PORT_SCIF,
- .irqs = SH4_SCIF_IRQS,
- .init_pins = sci_init_pins_scif,
- },
-#elif defined(CONFIG_CPU_SUBTYPE_SH7760)
- {
- .port = {
- .membase = (void *)0xfe600000,
- .mapbase = 0xfe600000,
- .iotype = UPIO_MEM,
- .irq = 55,
- .ops = &sci_uart_ops,
- .flags = UPF_BOOT_AUTOCONF,
- .line = 0,
- },
- .type = PORT_SCIF,
- .irqs = SH7760_SCIF0_IRQS,
- .init_pins = sci_init_pins_scif,
- },
- {
- .port = {
- .membase = (void *)0xfe610000,
- .mapbase = 0xfe610000,
- .iotype = UPIO_MEM,
- .irq = 75,
- .ops = &sci_uart_ops,
- .flags = UPF_BOOT_AUTOCONF,
- .line = 1,
- },
- .type = PORT_SCIF,
- .irqs = SH7760_SCIF1_IRQS,
- .init_pins = sci_init_pins_scif,
- },
- {
- .port = {
- .membase = (void *)0xfe620000,
- .mapbase = 0xfe620000,
- .iotype = UPIO_MEM,
- .irq = 79,
- .ops = &sci_uart_ops,
- .flags = UPF_BOOT_AUTOCONF,
- .line = 2,
- },
- .type = PORT_SCIF,
- .irqs = SH7760_SCIF2_IRQS,
- .init_pins = sci_init_pins_scif,
- },
-#elif defined(CONFIG_CPU_SUBTYPE_ST40STB1)
- {
- .port = {
- .membase = (void *)0xffe00000,
- .mapbase = 0xffe00000,
- .iotype = UPIO_MEM,
- .irq = 26,
- .ops = &sci_uart_ops,
- .flags = UPF_BOOT_AUTOCONF,
- .line = 0,
- },
- .type = PORT_SCIF,
- .irqs = STB1_SCIF1_IRQS,
- .init_pins = sci_init_pins_scif,
- },
- {
- .port = {
- .membase = (void *)0xffe80000,
- .mapbase = 0xffe80000,
- .iotype = UPIO_MEM,
- .irq = 43,
- .ops = &sci_uart_ops,
- .flags = UPF_BOOT_AUTOCONF,
- .line = 1,
- },
- .type = PORT_SCIF,
- .irqs = SH4_SCIF_IRQS,
- .init_pins = sci_init_pins_scif,
- },
-#elif defined(CONFIG_CPU_SUBTYPE_SH5_101) || defined(CONFIG_CPU_SUBTYPE_SH5_103)
- {
- .port = {
- .iotype = UPIO_MEM,
- .irq = 42,
- .ops = &sci_uart_ops,
- .flags = UPF_BOOT_AUTOCONF,
- .line = 0,
- },
- .type = PORT_SCIF,
- .irqs = SH5_SCIF_IRQS,
- .init_pins = sci_init_pins_scif,
- },
-#elif defined(CONFIG_H83007) || defined(CONFIG_H83068)
- {
- .port = {
- .membase = (void *)0x00ffffb0,
- .mapbase = 0x00ffffb0,
- .iotype = UPIO_MEM,
- .irq = 54,
- .ops = &sci_uart_ops,
- .flags = UPF_BOOT_AUTOCONF,
- .line = 0,
- },
- .type = PORT_SCI,
- .irqs = H8300H_SCI_IRQS0,
- .init_pins = sci_init_pins_sci,
- },
- {
- .port = {
- .membase = (void *)0x00ffffb8,
- .mapbase = 0x00ffffb8,
- .iotype = UPIO_MEM,
- .irq = 58,
- .ops = &sci_uart_ops,
- .flags = UPF_BOOT_AUTOCONF,
- .line = 1,
- },
- .type = PORT_SCI,
- .irqs = H8300H_SCI_IRQS1,
- .init_pins = sci_init_pins_sci,
- },
- {
- .port = {
- .membase = (void *)0x00ffffc0,
- .mapbase = 0x00ffffc0,
- .iotype = UPIO_MEM,
- .irq = 62,
- .ops = &sci_uart_ops,
- .flags = UPF_BOOT_AUTOCONF,
- .line = 2,
- },
- .type = PORT_SCI,
- .irqs = H8300H_SCI_IRQS2,
- .init_pins = sci_init_pins_sci,
- },
-#elif defined(CONFIG_H8S2678)
- {
- .port = {
- .membase = (void *)0x00ffff78,
- .mapbase = 0x00ffff78,
- .iotype = UPIO_MEM,
- .irq = 90,
- .ops = &sci_uart_ops,
- .flags = UPF_BOOT_AUTOCONF,
- .line = 0,
- },
- .type = PORT_SCI,
- .irqs = H8S_SCI_IRQS0,
- .init_pins = sci_init_pins_sci,
- },
- {
- .port = {
- .membase = (void *)0x00ffff80,
- .mapbase = 0x00ffff80,
- .iotype = UPIO_MEM,
- .irq = 94,
- .ops = &sci_uart_ops,
- .flags = UPF_BOOT_AUTOCONF,
- .line = 1,
- },
- .type = PORT_SCI,
- .irqs = H8S_SCI_IRQS1,
- .init_pins = sci_init_pins_sci,
- },
- {
- .port = {
- .membase = (void *)0x00ffff88,
- .mapbase = 0x00ffff88,
- .iotype = UPIO_MEM,
- .irq = 98,
- .ops = &sci_uart_ops,
- .flags = UPF_BOOT_AUTOCONF,
- .line = 2,
- },
- .type = PORT_SCI,
- .irqs = H8S_SCI_IRQS2,
- .init_pins = sci_init_pins_sci,
- },
-#elif defined(CONFIG_CPU_SUBTYPE_SH7770)
- {
- .port = {
- .membase = (void *)0xff923000,
- .mapbase = 0xff923000,
- .iotype = UPIO_MEM,
- .irq = 61,
- .ops = &sci_uart_ops,
- .flags = UPF_BOOT_AUTOCONF,
- .line = 0,
- },
- .type = PORT_SCIF,
- .irqs = SH7770_SCIF0_IRQS,
- .init_pins = sci_init_pins_scif,
- },
- {
- .port = {
- .membase = (void *)0xff924000,
- .mapbase = 0xff924000,
- .iotype = UPIO_MEM,
- .irq = 62,
- .ops = &sci_uart_ops,
- .flags = UPF_BOOT_AUTOCONF,
- .line = 1,
- },
- .type = PORT_SCIF,
- .irqs = SH7770_SCIF1_IRQS,
- .init_pins = sci_init_pins_scif,
- },
- {
- .port = {
- .membase = (void *)0xff925000,
- .mapbase = 0xff925000,
- .iotype = UPIO_MEM,
- .irq = 63,
- .ops = &sci_uart_ops,
- .flags = UPF_BOOT_AUTOCONF,
- .line = 2,
- },
- .type = PORT_SCIF,
- .irqs = SH7770_SCIF2_IRQS,
- .init_pins = sci_init_pins_scif,
- },
-#elif defined(CONFIG_CPU_SUBTYPE_SH7780)
- {
- .port = {
- .membase = (void *)0xffe00000,
- .mapbase = 0xffe00000,
- .iotype = UPIO_MEM,
- .irq = 43,
- .ops = &sci_uart_ops,
- .flags = UPF_BOOT_AUTOCONF,
- .line = 0,
- },
- .type = PORT_SCIF,
- .irqs = SH7780_SCIF0_IRQS,
- .init_pins = sci_init_pins_scif,
- },
- {
- .port = {
- .membase = (void *)0xffe10000,
- .mapbase = 0xffe10000,
- .iotype = UPIO_MEM,
- .irq = 79,
- .ops = &sci_uart_ops,
- .flags = UPF_BOOT_AUTOCONF,
- .line = 1,
- },
- .type = PORT_SCIF,
- .irqs = SH7780_SCIF1_IRQS,
- .init_pins = sci_init_pins_scif,
- },
-#else
-#error "CPU subtype not defined"
+static void __init sci_init_ports(void)
+{
+ static int first = 1;
+ int i;
+
+ if (!first)
+ return;
+
+ first = 0;
+
+ for (i = 0; i < SCI_NPORTS; i++) {
+ sci_ports[i].port.ops = &sci_uart_ops;
+ sci_ports[i].port.iotype = UPIO_MEM;
+ sci_ports[i].port.line = i;
+ sci_ports[i].port.fifosize = 1;
+
+#if defined(__H8300H__) || defined(__H8300S__)
+#ifdef __H8300S__
+ sci_ports[i].enable = h8300_sci_enable;
+ sci_ports[i].disable = h8300_sci_disable;
#endif
-};
+ sci_ports[i].port.uartclk = CONFIG_CPU_CLOCK;
+#elif defined(CONFIG_SUPERH64)
+ sci_ports[i].port.uartclk = current_cpu_data.module_clock * 16;
+#else
+ /*
+ * XXX: We should use a proper SCI/SCIF clock
+ */
+ {
+ struct clk *clk = clk_get("module_clk");
+ sci_ports[i].port.uartclk = clk_get_rate(clk) * 16;
+ clk_put(clk);
+ }
+#endif
+
+ sci_ports[i].break_timer.data = (unsigned long)&sci_ports[i];
+ sci_ports[i].break_timer.function = sci_break_timer;
+
+ init_timer(&sci_ports[i].break_timer);
+ }
+}
+
+int __init early_sci_setup(struct uart_port *port)
+{
+ if (unlikely(port->line > SCI_NPORTS))
+ return -ENODEV;
+
+ sci_init_ports();
+
+ sci_ports[port->line].port.membase = port->membase;
+ sci_ports[port->line].port.mapbase = port->mapbase;
+ sci_ports[port->line].port.type = port->type;
+
+ return 0;
+}
#ifdef CONFIG_SERIAL_SH_SCI_CONSOLE
/*
@@ -1559,34 +1177,38 @@
int flow = 'n';
int ret;
+ /*
+ * Check whether an invalid uart number has been specified, and
+ * if so, search for the first available port that does have
+ * console support.
+ */
+ if (co->index >= SCI_NPORTS)
+ co->index = 0;
+
serial_console_port = &sci_ports[co->index];
port = &serial_console_port->port;
- port->type = serial_console_port->type;
-
-#ifdef CONFIG_SUPERH64
- /* This is especially needed on sh64 to remap the SCIF */
- sci_config_port(port, 0);
-#endif
/*
- * We need to set the initial uartclk here, since otherwise it will
- * only ever be setup at sci_init() time.
+ * Also need to check port->type, we don't actually have any
+ * UPIO_PORT ports, but uart_report_port() handily misreports
+ * it anyways if we don't have a port available by the time this is
+ * called.
*/
-#if defined(__H8300H__) || defined(__H8300S__)
- port->uartclk = CONFIG_CPU_CLOCK;
+ if (!port->type)
+ return -ENODEV;
+ if (!port->membase || !port->mapbase)
+ return -ENODEV;
-#if defined(__H8300S__)
- h8300_sci_enable(port, sci_enable);
-#endif
-#elif defined(CONFIG_SUPERH64)
- port->uartclk = current_cpu_data.module_clock * 16;
-#else
- {
- struct clk *clk = clk_get("module_clk");
- port->uartclk = clk_get_rate(clk) * 16;
- clk_put(clk);
- }
-#endif
+ spin_lock_init(&port->lock);
+
+ port->type = serial_console_port->type;
+
+ if (port->flags & UPF_IOREMAP)
+ sci_config_port(port, 0);
+
+ if (serial_console_port->enable)
+ serial_console_port->enable(port);
+
if (options)
uart_parse_options(options, &baud, &parity, &bits, &flow);
@@ -1604,17 +1226,17 @@
.device = uart_console_device,
.write = serial_console_write,
.setup = serial_console_setup,
- .flags = CON_PRINTBUFFER,
+ .flags = CON_PRINTBUFFER,
.index = -1,
.data = &sci_uart_driver,
};
static int __init sci_console_init(void)
{
+ sci_init_ports();
register_console(&serial_console);
return 0;
}
-
console_initcall(sci_console_init);
#endif /* CONFIG_SERIAL_SH_SCI_CONSOLE */
@@ -1649,6 +1271,8 @@
int parity = 'n';
int flow = 'n';
+ spin_lock_init(&port->lock);
+
if (co->index != kgdb_portnum)
co->index = kgdb_portnum;
@@ -1677,10 +1301,10 @@
/* Register the KGDB console so we get messages (d'oh!) */
static int __init kgdb_console_init(void)
{
+ sci_init_ports();
register_console(&kgdb_console);
return 0;
}
-
console_initcall(kgdb_console_init);
#endif /* CONFIG_SH_KGDB_CONSOLE */
@@ -1701,60 +1325,132 @@
.dev_name = "ttySC",
.major = SCI_MAJOR,
.minor = SCI_MINOR_START,
+ .nr = SCI_NPORTS,
.cons = SCI_CONSOLE,
};
-static int __init sci_init(void)
+/*
+ * Register a set of serial devices attached to a platform device. The
+ * list is terminated with a zero flags entry, which means we expect
+ * all entries to have at least UPF_BOOT_AUTOCONF set. Platforms that need
+ * remapping (such as sh64) should also set UPF_IOREMAP.
+ */
+static int __devinit sci_probe(struct platform_device *dev)
{
- int chan, ret;
+ struct plat_sci_port *p = dev->dev.platform_data;
+ int i;
- printk("%s", banner);
+ for (i = 0; p && p->flags != 0 && i < SCI_NPORTS; p++, i++) {
+ struct sci_port *sciport = &sci_ports[i];
- sci_uart_driver.nr = ARRAY_SIZE(sci_ports);
+ sciport->port.mapbase = p->mapbase;
- ret = uart_register_driver(&sci_uart_driver);
- if (ret == 0) {
- for (chan = 0; chan < SCI_NPORTS; chan++) {
- struct sci_port *sciport = &sci_ports[chan];
+ /*
+ * For the simple (and majority of) cases where we don't need
+ * to do any remapping, just cast the cookie directly.
+ */
+ if (p->mapbase && !p->membase && !(p->flags & UPF_IOREMAP))
+ p->membase = (void __iomem *)p->mapbase;
-#if defined(__H8300H__) || defined(__H8300S__)
- sciport->port.uartclk = CONFIG_CPU_CLOCK;
-#elif defined(CONFIG_SUPERH64)
- sciport->port.uartclk = current_cpu_data.module_clock * 16;
-#else
- struct clk *clk = clk_get("module_clk");
- sciport->port.uartclk = clk_get_rate(clk) * 16;
- clk_put(clk);
-#endif
- uart_add_one_port(&sci_uart_driver, &sciport->port);
- sciport->break_timer.data = (unsigned long)sciport;
- sciport->break_timer.function = sci_break_timer;
- init_timer(&sciport->break_timer);
- }
+ sciport->port.membase = p->membase;
+
+ sciport->port.irq = p->irqs[SCIx_TXI_IRQ];
+ sciport->port.flags = p->flags;
+ sciport->port.dev = &dev->dev;
+
+ sciport->type = sciport->port.type = p->type;
+
+ memcpy(&sciport->irqs, &p->irqs, sizeof(p->irqs));
+
+ uart_add_one_port(&sci_uart_driver, &sciport->port);
}
#ifdef CONFIG_CPU_FREQ
cpufreq_register_notifier(&sci_nb, CPUFREQ_TRANSITION_NOTIFIER);
- printk("sci: CPU frequency notifier registered\n");
+ dev_info(&dev->dev, "sci: CPU frequency notifier registered\n");
#endif
#ifdef CONFIG_SH_STANDARD_BIOS
sh_bios_gdb_detach();
#endif
+ return 0;
+}
+
+static int __devexit sci_remove(struct platform_device *dev)
+{
+ int i;
+
+ for (i = 0; i < SCI_NPORTS; i++)
+ uart_remove_one_port(&sci_uart_driver, &sci_ports[i].port);
+
+ return 0;
+}
+
+static int sci_suspend(struct platform_device *dev, pm_message_t state)
+{
+ int i;
+
+ for (i = 0; i < SCI_NPORTS; i++) {
+ struct sci_port *p = &sci_ports[i];
+
+ if (p->type != PORT_UNKNOWN && p->port.dev == &dev->dev)
+ uart_suspend_port(&sci_uart_driver, &p->port);
+ }
+
+ return 0;
+}
+
+static int sci_resume(struct platform_device *dev)
+{
+ int i;
+
+ for (i = 0; i < SCI_NPORTS; i++) {
+ struct sci_port *p = &sci_ports[i];
+
+ if (p->type != PORT_UNKNOWN && p->port.dev == &dev->dev)
+ uart_resume_port(&sci_uart_driver, &p->port);
+ }
+
+ return 0;
+}
+
+static struct platform_driver sci_driver = {
+ .probe = sci_probe,
+ .remove = __devexit_p(sci_remove),
+ .suspend = sci_suspend,
+ .resume = sci_resume,
+ .driver = {
+ .name = "sh-sci",
+ .owner = THIS_MODULE,
+ },
+};
+
+static int __init sci_init(void)
+{
+ int ret;
+
+ printk(banner);
+
+ sci_init_ports();
+
+ ret = uart_register_driver(&sci_uart_driver);
+ if (likely(ret == 0)) {
+ ret = platform_driver_register(&sci_driver);
+ if (unlikely(ret))
+ uart_unregister_driver(&sci_uart_driver);
+ }
+
return ret;
}
static void __exit sci_exit(void)
{
- int chan;
-
- for (chan = 0; chan < SCI_NPORTS; chan++)
- uart_remove_one_port(&sci_uart_driver, &sci_ports[chan].port);
-
+ platform_driver_unregister(&sci_driver);
uart_unregister_driver(&sci_uart_driver);
}
module_init(sci_init);
module_exit(sci_exit);
+MODULE_LICENSE("GPL");