ath9k: add new ANI implementation for AR9003
This adds support for ANI for AR9003. The implementation for
ANI for AR9003 is slightly different than the one used for
the older chipset families. It can technically be used for
the older families as well but this is not yet fully tested
so we only enable the new ANI for the AR5008, AR9001 and AR9002
families with a module parameter, force_new_ani.
The old ANI implementation is left intact.
Details of the new ANI implemention:
* ANI adjustment logic is now table driven so that each ANI level
setting is parameterized. This makes adjustments much more
deterministic than the old procedure based logic and allows
adjustments to be made incrementally to several parameters per
level.
* ANI register settings are now relative to INI values; so ANI
param zero level == INI value. Appropriate floor and ceiling
values are obeyed when adjustments are combined with INI values.
* ANI processing is done once per second rather that every 100ms.
The poll interval is now a set upon hardware initialization and
can be picked up by the core driver.
* OFDM error and CCK error processing are made in a round robin
fashion rather than allowing all OFDM adjustments to be made
before CCK adjustments.
* ANI adjusts MRC CCK off in the presence of high CCK errors
* When adjusting spur immunity (SI) and OFDM weak signal detection,
ANI now sets register values for the extension channel too
* When adjusting FIR step (ST), ANI now sets register for FIR step
low too
* FIR step adjustments now allow for an extra level of immunity for
extremely noisy environments
* The old Noise immunity setting (NI), which changes coarse low, size
desired, etc have been removed. Changing these settings could affect
up RIFS RX as well.
* CCK weak signal adjustment is no longer used
* ANI no longer enables phy error interrupts; in all cases phy hw
counting registers are used instead
* The phy error count (overflow) interrupts are also no longer used
for ANI adjustments. All ANI adjustments are made via the polling
routine and no adjustments are possible in the ISR context anymore
* A history settings buffer is now correctly used for each channel;
channel settings are initialized with the defaults but later
changes are restored when returning back to that channel
* When scanning, ANI is disabled settings are returned to (INI) defaults.
* OFDM phy error thresholds are now 400 & 1000 (errors/second units) for
low/high water marks, providing increased stability/hysteresis when
changing levels.
* Similarly CCK phy error thresholds are now 300 & 600 (errors/second)
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
diff --git a/drivers/net/wireless/ath/ath9k/ar5008_phy.c b/drivers/net/wireless/ath/ath9k/ar5008_phy.c
index 96018d5..ee34a49 100644
--- a/drivers/net/wireless/ath/ath9k/ar5008_phy.c
+++ b/drivers/net/wireless/ath/ath9k/ar5008_phy.c
@@ -19,7 +19,30 @@
#include "../regd.h"
#include "ar9002_phy.h"
-/* All code below is for non single-chip solutions */
+/* All code below is for AR5008, AR9001, AR9002 */
+
+static const int firstep_table[] =
+/* level: 0 1 2 3 4 5 6 7 8 */
+ { -4, -2, 0, 2, 4, 6, 8, 10, 12 }; /* lvl 0-8, default 2 */
+
+static const int cycpwrThr1_table[] =
+/* level: 0 1 2 3 4 5 6 7 8 */
+ { -6, -4, -2, 0, 2, 4, 6, 8 }; /* lvl 0-7, default 3 */
+
+/*
+ * register values to turn OFDM weak signal detection OFF
+ */
+static const int m1ThreshLow_off = 127;
+static const int m2ThreshLow_off = 127;
+static const int m1Thresh_off = 127;
+static const int m2Thresh_off = 127;
+static const int m2CountThr_off = 31;
+static const int m2CountThrLow_off = 63;
+static const int m1ThreshLowExt_off = 127;
+static const int m2ThreshLowExt_off = 127;
+static const int m1ThreshExt_off = 127;
+static const int m2ThreshExt_off = 127;
+
/**
* ar5008_hw_phy_modify_rx_buffer() - perform analog swizzling of parameters
@@ -1026,8 +1049,9 @@
return pll;
}
-static bool ar5008_hw_ani_control(struct ath_hw *ah,
- enum ath9k_ani_cmd cmd, int param)
+static bool ar5008_hw_ani_control_old(struct ath_hw *ah,
+ enum ath9k_ani_cmd cmd,
+ int param)
{
struct ar5416AniState *aniState = ah->curani;
struct ath_common *common = ath9k_hw_common(ah);
@@ -1209,6 +1233,265 @@
return true;
}
+static bool ar5008_hw_ani_control_new(struct ath_hw *ah,
+ enum ath9k_ani_cmd cmd,
+ int param)
+{
+ struct ar5416AniState *aniState = ah->curani;
+ struct ath_common *common = ath9k_hw_common(ah);
+ struct ath9k_channel *chan = ah->curchan;
+ s32 value, value2;
+
+ switch (cmd & ah->ani_function) {
+ case ATH9K_ANI_OFDM_WEAK_SIGNAL_DETECTION:{
+ /*
+ * on == 1 means ofdm weak signal detection is ON
+ * on == 1 is the default, for less noise immunity
+ *
+ * on == 0 means ofdm weak signal detection is OFF
+ * on == 0 means more noise imm
+ */
+ u32 on = param ? 1 : 0;
+ /*
+ * make register setting for default
+ * (weak sig detect ON) come from INI file
+ */
+ int m1ThreshLow = on ?
+ aniState->iniDef.m1ThreshLow : m1ThreshLow_off;
+ int m2ThreshLow = on ?
+ aniState->iniDef.m2ThreshLow : m2ThreshLow_off;
+ int m1Thresh = on ?
+ aniState->iniDef.m1Thresh : m1Thresh_off;
+ int m2Thresh = on ?
+ aniState->iniDef.m2Thresh : m2Thresh_off;
+ int m2CountThr = on ?
+ aniState->iniDef.m2CountThr : m2CountThr_off;
+ int m2CountThrLow = on ?
+ aniState->iniDef.m2CountThrLow : m2CountThrLow_off;
+ int m1ThreshLowExt = on ?
+ aniState->iniDef.m1ThreshLowExt : m1ThreshLowExt_off;
+ int m2ThreshLowExt = on ?
+ aniState->iniDef.m2ThreshLowExt : m2ThreshLowExt_off;
+ int m1ThreshExt = on ?
+ aniState->iniDef.m1ThreshExt : m1ThreshExt_off;
+ int m2ThreshExt = on ?
+ aniState->iniDef.m2ThreshExt : m2ThreshExt_off;
+
+ REG_RMW_FIELD(ah, AR_PHY_SFCORR_LOW,
+ AR_PHY_SFCORR_LOW_M1_THRESH_LOW,
+ m1ThreshLow);
+ REG_RMW_FIELD(ah, AR_PHY_SFCORR_LOW,
+ AR_PHY_SFCORR_LOW_M2_THRESH_LOW,
+ m2ThreshLow);
+ REG_RMW_FIELD(ah, AR_PHY_SFCORR,
+ AR_PHY_SFCORR_M1_THRESH, m1Thresh);
+ REG_RMW_FIELD(ah, AR_PHY_SFCORR,
+ AR_PHY_SFCORR_M2_THRESH, m2Thresh);
+ REG_RMW_FIELD(ah, AR_PHY_SFCORR,
+ AR_PHY_SFCORR_M2COUNT_THR, m2CountThr);
+ REG_RMW_FIELD(ah, AR_PHY_SFCORR_LOW,
+ AR_PHY_SFCORR_LOW_M2COUNT_THR_LOW,
+ m2CountThrLow);
+
+ REG_RMW_FIELD(ah, AR_PHY_SFCORR_EXT,
+ AR_PHY_SFCORR_EXT_M1_THRESH_LOW, m1ThreshLowExt);
+ REG_RMW_FIELD(ah, AR_PHY_SFCORR_EXT,
+ AR_PHY_SFCORR_EXT_M2_THRESH_LOW, m2ThreshLowExt);
+ REG_RMW_FIELD(ah, AR_PHY_SFCORR_EXT,
+ AR_PHY_SFCORR_EXT_M1_THRESH, m1ThreshExt);
+ REG_RMW_FIELD(ah, AR_PHY_SFCORR_EXT,
+ AR_PHY_SFCORR_EXT_M2_THRESH, m2ThreshExt);
+
+ if (on)
+ REG_SET_BIT(ah, AR_PHY_SFCORR_LOW,
+ AR_PHY_SFCORR_LOW_USE_SELF_CORR_LOW);
+ else
+ REG_CLR_BIT(ah, AR_PHY_SFCORR_LOW,
+ AR_PHY_SFCORR_LOW_USE_SELF_CORR_LOW);
+
+ if (!on != aniState->ofdmWeakSigDetectOff) {
+ ath_print(common, ATH_DBG_ANI,
+ "** ch %d: ofdm weak signal: %s=>%s\n",
+ chan->channel,
+ !aniState->ofdmWeakSigDetectOff ?
+ "on" : "off",
+ on ? "on" : "off");
+ if (on)
+ ah->stats.ast_ani_ofdmon++;
+ else
+ ah->stats.ast_ani_ofdmoff++;
+ aniState->ofdmWeakSigDetectOff = !on;
+ }
+ break;
+ }
+ case ATH9K_ANI_FIRSTEP_LEVEL:{
+ u32 level = param;
+
+ if (level >= ARRAY_SIZE(firstep_table)) {
+ ath_print(common, ATH_DBG_ANI,
+ "ATH9K_ANI_FIRSTEP_LEVEL: level "
+ "out of range (%u > %u)\n",
+ level,
+ (unsigned) ARRAY_SIZE(firstep_table));
+ return false;
+ }
+
+ /*
+ * make register setting relative to default
+ * from INI file & cap value
+ */
+ value = firstep_table[level] -
+ firstep_table[ATH9K_ANI_FIRSTEP_LVL_NEW] +
+ aniState->iniDef.firstep;
+ if (value < ATH9K_SIG_FIRSTEP_SETTING_MIN)
+ value = ATH9K_SIG_FIRSTEP_SETTING_MIN;
+ if (value > ATH9K_SIG_FIRSTEP_SETTING_MAX)
+ value = ATH9K_SIG_FIRSTEP_SETTING_MAX;
+ REG_RMW_FIELD(ah, AR_PHY_FIND_SIG,
+ AR_PHY_FIND_SIG_FIRSTEP,
+ value);
+ /*
+ * we need to set first step low register too
+ * make register setting relative to default
+ * from INI file & cap value
+ */
+ value2 = firstep_table[level] -
+ firstep_table[ATH9K_ANI_FIRSTEP_LVL_NEW] +
+ aniState->iniDef.firstepLow;
+ if (value2 < ATH9K_SIG_FIRSTEP_SETTING_MIN)
+ value2 = ATH9K_SIG_FIRSTEP_SETTING_MIN;
+ if (value2 > ATH9K_SIG_FIRSTEP_SETTING_MAX)
+ value2 = ATH9K_SIG_FIRSTEP_SETTING_MAX;
+
+ REG_RMW_FIELD(ah, AR_PHY_FIND_SIG_LOW,
+ AR_PHY_FIND_SIG_FIRSTEP_LOW, value2);
+
+ if (level != aniState->firstepLevel) {
+ ath_print(common, ATH_DBG_ANI,
+ "** ch %d: level %d=>%d[def:%d] "
+ "firstep[level]=%d ini=%d\n",
+ chan->channel,
+ aniState->firstepLevel,
+ level,
+ ATH9K_ANI_FIRSTEP_LVL_NEW,
+ value,
+ aniState->iniDef.firstep);
+ ath_print(common, ATH_DBG_ANI,
+ "** ch %d: level %d=>%d[def:%d] "
+ "firstep_low[level]=%d ini=%d\n",
+ chan->channel,
+ aniState->firstepLevel,
+ level,
+ ATH9K_ANI_FIRSTEP_LVL_NEW,
+ value2,
+ aniState->iniDef.firstepLow);
+ if (level > aniState->firstepLevel)
+ ah->stats.ast_ani_stepup++;
+ else if (level < aniState->firstepLevel)
+ ah->stats.ast_ani_stepdown++;
+ aniState->firstepLevel = level;
+ }
+ break;
+ }
+ case ATH9K_ANI_SPUR_IMMUNITY_LEVEL:{
+ u32 level = param;
+
+ if (level >= ARRAY_SIZE(cycpwrThr1_table)) {
+ ath_print(common, ATH_DBG_ANI,
+ "ATH9K_ANI_SPUR_IMMUNITY_LEVEL: level "
+ "out of range (%u > %u)\n",
+ level,
+ (unsigned) ARRAY_SIZE(cycpwrThr1_table));
+ return false;
+ }
+ /*
+ * make register setting relative to default
+ * from INI file & cap value
+ */
+ value = cycpwrThr1_table[level] -
+ cycpwrThr1_table[ATH9K_ANI_SPUR_IMMUNE_LVL_NEW] +
+ aniState->iniDef.cycpwrThr1;
+ if (value < ATH9K_SIG_SPUR_IMM_SETTING_MIN)
+ value = ATH9K_SIG_SPUR_IMM_SETTING_MIN;
+ if (value > ATH9K_SIG_SPUR_IMM_SETTING_MAX)
+ value = ATH9K_SIG_SPUR_IMM_SETTING_MAX;
+ REG_RMW_FIELD(ah, AR_PHY_TIMING5,
+ AR_PHY_TIMING5_CYCPWR_THR1,
+ value);
+
+ /*
+ * set AR_PHY_EXT_CCA for extension channel
+ * make register setting relative to default
+ * from INI file & cap value
+ */
+ value2 = cycpwrThr1_table[level] -
+ cycpwrThr1_table[ATH9K_ANI_SPUR_IMMUNE_LVL_NEW] +
+ aniState->iniDef.cycpwrThr1Ext;
+ if (value2 < ATH9K_SIG_SPUR_IMM_SETTING_MIN)
+ value2 = ATH9K_SIG_SPUR_IMM_SETTING_MIN;
+ if (value2 > ATH9K_SIG_SPUR_IMM_SETTING_MAX)
+ value2 = ATH9K_SIG_SPUR_IMM_SETTING_MAX;
+ REG_RMW_FIELD(ah, AR_PHY_EXT_CCA,
+ AR_PHY_EXT_TIMING5_CYCPWR_THR1, value2);
+
+ if (level != aniState->spurImmunityLevel) {
+ ath_print(common, ATH_DBG_ANI,
+ "** ch %d: level %d=>%d[def:%d] "
+ "cycpwrThr1[level]=%d ini=%d\n",
+ chan->channel,
+ aniState->spurImmunityLevel,
+ level,
+ ATH9K_ANI_SPUR_IMMUNE_LVL_NEW,
+ value,
+ aniState->iniDef.cycpwrThr1);
+ ath_print(common, ATH_DBG_ANI,
+ "** ch %d: level %d=>%d[def:%d] "
+ "cycpwrThr1Ext[level]=%d ini=%d\n",
+ chan->channel,
+ aniState->spurImmunityLevel,
+ level,
+ ATH9K_ANI_SPUR_IMMUNE_LVL_NEW,
+ value2,
+ aniState->iniDef.cycpwrThr1Ext);
+ if (level > aniState->spurImmunityLevel)
+ ah->stats.ast_ani_spurup++;
+ else if (level < aniState->spurImmunityLevel)
+ ah->stats.ast_ani_spurdown++;
+ aniState->spurImmunityLevel = level;
+ }
+ break;
+ }
+ case ATH9K_ANI_MRC_CCK:
+ /*
+ * You should not see this as AR5008, AR9001, AR9002
+ * does not have hardware support for MRC CCK.
+ */
+ WARN_ON(1);
+ break;
+ case ATH9K_ANI_PRESENT:
+ break;
+ default:
+ ath_print(common, ATH_DBG_ANI,
+ "invalid cmd %u\n", cmd);
+ return false;
+ }
+
+ ath_print(common, ATH_DBG_ANI,
+ "ANI parameters: SI=%d, ofdmWS=%s FS=%d "
+ "MRCcck=%s listenTime=%d CC=%d listen=%d "
+ "ofdmErrs=%d cckErrs=%d\n",
+ aniState->spurImmunityLevel,
+ !aniState->ofdmWeakSigDetectOff ? "on" : "off",
+ aniState->firstepLevel,
+ !aniState->mrcCCKOff ? "on" : "off",
+ aniState->listenTime,
+ aniState->cycleCount,
+ aniState->listenTime,
+ aniState->ofdmPhyErrCount,
+ aniState->cckPhyErrCount);
+ return true;
+}
+
static void ar5008_hw_do_getnf(struct ath_hw *ah,
int16_t nfarray[NUM_NF_READINGS])
{
@@ -1329,6 +1612,71 @@
DISABLE_REGWRITE_BUFFER(ah);
}
+/*
+ * Initialize the ANI register values with default (ini) values.
+ * This routine is called during a (full) hardware reset after
+ * all the registers are initialised from the INI.
+ */
+static void ar5008_hw_ani_cache_ini_regs(struct ath_hw *ah)
+{
+ struct ar5416AniState *aniState;
+ struct ath_common *common = ath9k_hw_common(ah);
+ struct ath9k_channel *chan = ah->curchan;
+ struct ath9k_ani_default *iniDef;
+ int index;
+ u32 val;
+
+ index = ath9k_hw_get_ani_channel_idx(ah, chan);
+ aniState = &ah->ani[index];
+ ah->curani = aniState;
+ iniDef = &aniState->iniDef;
+
+ ath_print(common, ATH_DBG_ANI,
+ "ver %d.%d opmode %u chan %d Mhz/0x%x\n",
+ ah->hw_version.macVersion,
+ ah->hw_version.macRev,
+ ah->opmode,
+ chan->channel,
+ chan->channelFlags);
+
+ val = REG_READ(ah, AR_PHY_SFCORR);
+ iniDef->m1Thresh = MS(val, AR_PHY_SFCORR_M1_THRESH);
+ iniDef->m2Thresh = MS(val, AR_PHY_SFCORR_M2_THRESH);
+ iniDef->m2CountThr = MS(val, AR_PHY_SFCORR_M2COUNT_THR);
+
+ val = REG_READ(ah, AR_PHY_SFCORR_LOW);
+ iniDef->m1ThreshLow = MS(val, AR_PHY_SFCORR_LOW_M1_THRESH_LOW);
+ iniDef->m2ThreshLow = MS(val, AR_PHY_SFCORR_LOW_M2_THRESH_LOW);
+ iniDef->m2CountThrLow = MS(val, AR_PHY_SFCORR_LOW_M2COUNT_THR_LOW);
+
+ val = REG_READ(ah, AR_PHY_SFCORR_EXT);
+ iniDef->m1ThreshExt = MS(val, AR_PHY_SFCORR_EXT_M1_THRESH);
+ iniDef->m2ThreshExt = MS(val, AR_PHY_SFCORR_EXT_M2_THRESH);
+ iniDef->m1ThreshLowExt = MS(val, AR_PHY_SFCORR_EXT_M1_THRESH_LOW);
+ iniDef->m2ThreshLowExt = MS(val, AR_PHY_SFCORR_EXT_M2_THRESH_LOW);
+ iniDef->firstep = REG_READ_FIELD(ah,
+ AR_PHY_FIND_SIG,
+ AR_PHY_FIND_SIG_FIRSTEP);
+ iniDef->firstepLow = REG_READ_FIELD(ah,
+ AR_PHY_FIND_SIG_LOW,
+ AR_PHY_FIND_SIG_FIRSTEP_LOW);
+ iniDef->cycpwrThr1 = REG_READ_FIELD(ah,
+ AR_PHY_TIMING5,
+ AR_PHY_TIMING5_CYCPWR_THR1);
+ iniDef->cycpwrThr1Ext = REG_READ_FIELD(ah,
+ AR_PHY_EXT_CCA,
+ AR_PHY_EXT_TIMING5_CYCPWR_THR1);
+
+ /* these levels just got reset to defaults by the INI */
+ aniState->spurImmunityLevel = ATH9K_ANI_SPUR_IMMUNE_LVL_NEW;
+ aniState->firstepLevel = ATH9K_ANI_FIRSTEP_LVL_NEW;
+ aniState->ofdmWeakSigDetectOff = !ATH9K_ANI_USE_OFDM_WEAK_SIG;
+ aniState->mrcCCKOff = true; /* not available on pre AR9003 */
+
+ aniState->cycleCount = 0;
+}
+
+
void ar5008_hw_attach_phy_ops(struct ath_hw *ah)
{
struct ath_hw_private_ops *priv_ops = ath9k_hw_private_ops(ah);
@@ -1350,10 +1698,15 @@
priv_ops->enable_rfkill = ar5008_hw_enable_rfkill;
priv_ops->restore_chainmask = ar5008_restore_chainmask;
priv_ops->set_diversity = ar5008_set_diversity;
- priv_ops->ani_control = ar5008_hw_ani_control;
priv_ops->do_getnf = ar5008_hw_do_getnf;
priv_ops->loadnf = ar5008_hw_loadnf;
+ if (modparam_force_new_ani) {
+ priv_ops->ani_control = ar5008_hw_ani_control_new;
+ priv_ops->ani_cache_ini_regs = ar5008_hw_ani_cache_ini_regs;
+ } else
+ priv_ops->ani_control = ar5008_hw_ani_control_old;
+
if (AR_SREV_9100(ah))
priv_ops->compute_pll_control = ar9100_hw_compute_pll_control;
else if (AR_SREV_9160_10_OR_LATER(ah))