drivers/pcmcia/au1000_pb1x00.c - kernel/msm - Gitiles

 /*
  *
  * Alchemy Semi Pb1x00 boards specific pcmcia routines.
  *
  * Copyright 2002 MontaVista Software Inc.
  * Author: MontaVista Software, Inc.
  *         	ppopov@mvista.com or source@mvista.com
  *
  * ########################################################################
  *
  *  This program is free software; you can distribute it and/or modify it
  *  under the terms of the GNU General Public License (Version 2) as
  *  published by the Free Software Foundation.
  *
  *  This program is distributed in the hope it will be useful, but WITHOUT
  *  ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or
  *  FITNESS FOR A PARTICULAR PURPOSE.  See the GNU General Public License
  *  for more details.
  *
  *  You should have received a copy of the GNU General Public License along
  *  with this program; if not, write to the Free Software Foundation, Inc.,
  *  59 Temple Place - Suite 330, Boston MA 02111-1307, USA.
  */
 #include <linux/module.h>
 #include <linux/init.h>
 #include <linux/delay.h>
 #include <linux/ioport.h>
 #include <linux/kernel.h>
 #include <linux/tqueue.h>
 #include <linux/timer.h>
 #include <linux/mm.h>
 #include <linux/proc_fs.h>
 #include <linux/version.h>
 #include <linux/types.h>

 #include <pcmcia/cs_types.h>
 #include <pcmcia/cs.h>
 #include <pcmcia/ss.h>
 #include <pcmcia/bulkmem.h>
 #include <pcmcia/cistpl.h>
 #include <pcmcia/bus_ops.h>
 #include "cs_internal.h"

 #include <asm/io.h>
 #include <asm/irq.h>
 #include <asm/system.h>

 #include <asm/au1000.h>
 #include <asm/au1000_pcmcia.h>

 #define debug(fmt, arg...) do { } while (0)

 #ifdef CONFIG_MIPS_PB1000
 #include <asm/pb1000.h>
 #define PCMCIA_IRQ AU1000_GPIO_15
 #elif defined (CONFIG_MIPS_PB1500)
 #include <asm/pb1500.h>
 #define PCMCIA_IRQ AU1500_GPIO_203
 #elif defined (CONFIG_MIPS_PB1100)
 #include <asm/pb1100.h>
 #define PCMCIA_IRQ AU1000_GPIO_11
 #endif

 static int pb1x00_pcmcia_init(struct pcmcia_init *init)
 {
 #ifdef CONFIG_MIPS_PB1000
 	u16 pcr;
 	pcr = PCR_SLOT_0_RST | PCR_SLOT_1_RST;

 	au_writel(0x8000, PB1000_MDR); /* clear pcmcia interrupt */
 	au_sync_delay(100);
 	au_writel(0x4000, PB1000_MDR); /* enable pcmcia interrupt */
 	au_sync();

 	pcr |= SET_VCC_VPP(VCC_HIZ,VPP_HIZ,0);
 	pcr |= SET_VCC_VPP(VCC_HIZ,VPP_HIZ,1);
 	au_writel(pcr, PB1000_PCR);
 	au_sync_delay(20);

 	return PCMCIA_NUM_SOCKS;

 #else /* fixme -- take care of the Pb1500 at some point */

 	u16 pcr;
 	pcr = au_readw(PCMCIA_BOARD_REG) & ~0xf; /* turn off power */
 	pcr &= ~(PC_DEASSERT_RST | PC_DRV_EN);
 	au_writew(pcr, PCMCIA_BOARD_REG);
 	au_sync_delay(500);
 	return PCMCIA_NUM_SOCKS;
 #endif
 }

 static int pb1x00_pcmcia_shutdown(void)
 {
 #ifdef CONFIG_MIPS_PB1000
 	u16 pcr;
 	pcr = PCR_SLOT_0_RST | PCR_SLOT_1_RST;
 	pcr |= SET_VCC_VPP(VCC_HIZ,VPP_HIZ,0);
 	pcr |= SET_VCC_VPP(VCC_HIZ,VPP_HIZ,1);
 	au_writel(pcr, PB1000_PCR);
 	au_sync_delay(20);
 	return 0;
 #else
 	u16 pcr;
 	pcr = au_readw(PCMCIA_BOARD_REG) & ~0xf; /* turn off power */
 	pcr &= ~(PC_DEASSERT_RST | PC_DRV_EN);
 	au_writew(pcr, PCMCIA_BOARD_REG);
 	au_sync_delay(2);
 	return 0;
 #endif
 }

 static int
 pb1x00_pcmcia_socket_state(unsigned sock, struct pcmcia_state *state)
 {
 	u32 inserted0, inserted1;
 	u16 vs0, vs1;

 #ifdef CONFIG_MIPS_PB1000
 	vs0 = vs1 = (u16)au_readl(PB1000_ACR1);
 	inserted0 = !(vs0 & (ACR1_SLOT_0_CD1 | ACR1_SLOT_0_CD2));
 	inserted1 = !(vs1 & (ACR1_SLOT_1_CD1 | ACR1_SLOT_1_CD2));
 	vs0 = (vs0 >> 4) & 0x3;
 	vs1 = (vs1 >> 12) & 0x3;
 #else
 	vs0 = (au_readw(BOARD_STATUS_REG) >> 4) & 0x3;
 #ifdef CONFIG_MIPS_PB1500
 	inserted0 = !((au_readl(GPIO2_PINSTATE) >> 1) & 0x1); /* gpio 201 */
 #else /* Pb1100 */
 	inserted0 = !((au_readl(SYS_PINSTATERD) >> 9) & 0x1); /* gpio 9 */
 #endif
 	inserted1 = 0;
 #endif

 	state->ready = 0;
 	state->vs_Xv = 0;
 	state->vs_3v = 0;
 	state->detect = 0;

 	if (sock == 0) {
 		if (inserted0) {
 			switch (vs0) {
 				case 0:
 				case 2:
 					state->vs_3v=1;
 					break;
 				case 3: /* 5V */
 					break;
 				default:
 					/* return without setting 'detect' */
 					printk(KERN_ERR "pb1x00 bad VS (%d)\n",
 							vs0);
 					return 0;
 			}
 			state->detect = 1;
 		}
 	}
 	else  {
 		if (inserted1) {
 			switch (vs1) {
 				case 0:
 				case 2:
 					state->vs_3v=1;
 					break;
 				case 3: /* 5V */
 					break;
 				default:
 					/* return without setting 'detect' */
 					printk(KERN_ERR "pb1x00 bad VS (%d)\n",
 							vs1);
 					return 0;
 			}
 			state->detect = 1;
 		}
 	}

 	if (state->detect) {
 		state->ready = 1;
 	}

 	state->bvd1=1;
 	state->bvd2=1;
 	state->wrprot=0;
 	return 1;
 }


 static int pb1x00_pcmcia_get_irq_info(struct pcmcia_irq_info *info)
 {

 	if(info->sock > PCMCIA_MAX_SOCK) return -1;

 	/*
 	 * Even in the case of the Pb1000, both sockets are connected
 	 * to the same irq line.
 	 */
 	info->irq = PCMCIA_IRQ;

 	return 0;
 }


 static int
 pb1x00_pcmcia_configure_socket(const struct pcmcia_configure *configure)
 {
 	u16 pcr;

 	if(configure->sock > PCMCIA_MAX_SOCK) return -1;

 #ifdef CONFIG_MIPS_PB1000
 	pcr = au_readl(PB1000_PCR);

 	if (configure->sock == 0) {
 		pcr &= ~(PCR_SLOT_0_VCC0 | PCR_SLOT_0_VCC1 |
 				PCR_SLOT_0_VPP0 | PCR_SLOT_0_VPP1);
 	}
 	else  {
 		pcr &= ~(PCR_SLOT_1_VCC0 | PCR_SLOT_1_VCC1 |
 				PCR_SLOT_1_VPP0 | PCR_SLOT_1_VPP1);
 	}

 	pcr &= ~PCR_SLOT_0_RST;
 	debug("Vcc %dV Vpp %dV, pcr %x\n",
 			configure->vcc, configure->vpp, pcr);
 	switch(configure->vcc){
 		case 0:  /* Vcc 0 */
 			switch(configure->vpp) {
 				case 0:
 					pcr |= SET_VCC_VPP(VCC_HIZ,VPP_GND,
 							configure->sock);
 					break;
 				case 12:
 					pcr |= SET_VCC_VPP(VCC_HIZ,VPP_12V,
 							configure->sock);
 					break;
 				case 50:
 					pcr |= SET_VCC_VPP(VCC_HIZ,VPP_5V,
 							configure->sock);
 					break;
 				case 33:
 					pcr |= SET_VCC_VPP(VCC_HIZ,VPP_3V,
 							configure->sock);
 					break;
 				default:
 					pcr |= SET_VCC_VPP(VCC_HIZ,VPP_HIZ,
 							configure->sock);
 					printk("%s: bad Vcc/Vpp (%d:%d)\n",
 							__FUNCTION__,
 							configure->vcc,
 							configure->vpp);
 					break;
 			}
 			break;
 		case 50: /* Vcc 5V */
 			switch(configure->vpp) {
 				case 0:
 					pcr |= SET_VCC_VPP(VCC_5V,VPP_GND,
 							configure->sock);
 					break;
 				case 50:
 					pcr |= SET_VCC_VPP(VCC_5V,VPP_5V,
 							configure->sock);
 					break;
 				case 12:
 					pcr |= SET_VCC_VPP(VCC_5V,VPP_12V,
 							configure->sock);
 					break;
 				case 33:
 					pcr |= SET_VCC_VPP(VCC_5V,VPP_3V,
 							configure->sock);
 					break;
 				default:
 					pcr |= SET_VCC_VPP(VCC_HIZ,VPP_HIZ,
 							configure->sock);
 					printk("%s: bad Vcc/Vpp (%d:%d)\n",
 							__FUNCTION__,
 							configure->vcc,
 							configure->vpp);
 					break;
 			}
 			break;
 		case 33: /* Vcc 3.3V */
 			switch(configure->vpp) {
 				case 0:
 					pcr |= SET_VCC_VPP(VCC_3V,VPP_GND,
 							configure->sock);
 					break;
 				case 50:
 					pcr |= SET_VCC_VPP(VCC_3V,VPP_5V,
 							configure->sock);
 					break;
 				case 12:
 					pcr |= SET_VCC_VPP(VCC_3V,VPP_12V,
 							configure->sock);
 					break;
 				case 33:
 					pcr |= SET_VCC_VPP(VCC_3V,VPP_3V,
 							configure->sock);
 					break;
 				default:
 					pcr |= SET_VCC_VPP(VCC_HIZ,VPP_HIZ,
 							configure->sock);
 					printk("%s: bad Vcc/Vpp (%d:%d)\n",
 							__FUNCTION__,
 							configure->vcc,
 							configure->vpp);
 					break;
 			}
 			break;
 		default: /* what's this ? */
 			pcr |= SET_VCC_VPP(VCC_HIZ,VPP_HIZ,configure->sock);
 			printk(KERN_ERR "%s: bad Vcc %d\n",
 					__FUNCTION__, configure->vcc);
 			break;
 	}

 	if (configure->sock == 0) {
 	pcr &= ~(PCR_SLOT_0_RST);
 		if (configure->reset)
 		pcr |= PCR_SLOT_0_RST;
 	}
 	else {
 		pcr &= ~(PCR_SLOT_1_RST);
 		if (configure->reset)
 			pcr |= PCR_SLOT_1_RST;
 	}
 	au_writel(pcr, PB1000_PCR);
 	au_sync_delay(300);

 #else

 	pcr = au_readw(PCMCIA_BOARD_REG) & ~0xf;

 	debug("Vcc %dV Vpp %dV, pcr %x, reset %d\n",
 			configure->vcc, configure->vpp, pcr, configure->reset);


 	switch(configure->vcc){
 		case 0:  /* Vcc 0 */
 			pcr |= SET_VCC_VPP(0,0);
 			break;
 		case 50: /* Vcc 5V */
 			switch(configure->vpp) {
 				case 0:
 					pcr |= SET_VCC_VPP(2,0);
 					break;
 				case 50:
 					pcr |= SET_VCC_VPP(2,1);
 					break;
 				case 12:
 					pcr |= SET_VCC_VPP(2,2);
 					break;
 				case 33:
 				default:
 					pcr |= SET_VCC_VPP(0,0);
 					printk("%s: bad Vcc/Vpp (%d:%d)\n",
 							__FUNCTION__,
 							configure->vcc,
 							configure->vpp);
 					break;
 			}
 			break;
 		case 33: /* Vcc 3.3V */
 			switch(configure->vpp) {
 				case 0:
 					pcr |= SET_VCC_VPP(1,0);
 					break;
 				case 12:
 					pcr |= SET_VCC_VPP(1,2);
 					break;
 				case 33:
 					pcr |= SET_VCC_VPP(1,1);
 					break;
 				case 50:
 				default:
 					pcr |= SET_VCC_VPP(0,0);
 					printk("%s: bad Vcc/Vpp (%d:%d)\n",
 							__FUNCTION__,
 							configure->vcc,
 							configure->vpp);
 					break;
 			}
 			break;
 		default: /* what's this ? */
 			pcr |= SET_VCC_VPP(0,0);
 			printk(KERN_ERR "%s: bad Vcc %d\n",
 					__FUNCTION__, configure->vcc);
 			break;
 	}

 	au_writew(pcr, PCMCIA_BOARD_REG);
 	au_sync_delay(300);

 	if (!configure->reset) {
 		pcr |= PC_DRV_EN;
 		au_writew(pcr, PCMCIA_BOARD_REG);
 		au_sync_delay(100);
 		pcr |= PC_DEASSERT_RST;
 		au_writew(pcr, PCMCIA_BOARD_REG);
 		au_sync_delay(100);
 	}
 	else {
 		pcr &= ~(PC_DEASSERT_RST | PC_DRV_EN);
 		au_writew(pcr, PCMCIA_BOARD_REG);
 		au_sync_delay(100);
 	}
 #endif
 	return 0;
 }


 struct pcmcia_low_level pb1x00_pcmcia_ops = {
 	pb1x00_pcmcia_init,
 	pb1x00_pcmcia_shutdown,
 	pb1x00_pcmcia_socket_state,
 	pb1x00_pcmcia_get_irq_info,
 	pb1x00_pcmcia_configure_socket
 };
	/*
	*
	* Alchemy Semi Pb1x00 boards specific pcmcia routines.
	*
	* Copyright 2002 MontaVista Software Inc.
	* Author: MontaVista Software, Inc.
	* ppopov@mvista.com or source@mvista.com
	*
	* ########################################################################
	*
	* This program is free software; you can distribute it and/or modify it
	* under the terms of the GNU General Public License (Version 2) as
	* published by the Free Software Foundation.
	*
	* This program is distributed in the hope it will be useful, but WITHOUT
	* ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or
	* FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License
	* for more details.
	*
	* You should have received a copy of the GNU General Public License along
	* with this program; if not, write to the Free Software Foundation, Inc.,
	* 59 Temple Place - Suite 330, Boston MA 02111-1307, USA.
	*/
	#include <linux/module.h>
	#include <linux/init.h>
	#include <linux/delay.h>
	#include <linux/ioport.h>
	#include <linux/kernel.h>
	#include <linux/tqueue.h>
	#include <linux/timer.h>
	#include <linux/mm.h>
	#include <linux/proc_fs.h>
	#include <linux/version.h>
	#include <linux/types.h>

	#include <pcmcia/cs_types.h>
	#include <pcmcia/cs.h>
	#include <pcmcia/ss.h>
	#include <pcmcia/bulkmem.h>
	#include <pcmcia/cistpl.h>
	#include <pcmcia/bus_ops.h>
	#include "cs_internal.h"

	#include <asm/io.h>
	#include <asm/irq.h>
	#include <asm/system.h>

	#include <asm/au1000.h>
	#include <asm/au1000_pcmcia.h>

	#define debug(fmt, arg...) do { } while (0)

	#ifdef CONFIG_MIPS_PB1000
	#include <asm/pb1000.h>
	#define PCMCIA_IRQ AU1000_GPIO_15
	#elif defined (CONFIG_MIPS_PB1500)
	#include <asm/pb1500.h>
	#define PCMCIA_IRQ AU1500_GPIO_203
	#elif defined (CONFIG_MIPS_PB1100)
	#include <asm/pb1100.h>
	#define PCMCIA_IRQ AU1000_GPIO_11
	#endif

	static int pb1x00_pcmcia_init(struct pcmcia_init *init)
	{
	#ifdef CONFIG_MIPS_PB1000
	u16 pcr;
	pcr = PCR_SLOT_0_RST \| PCR_SLOT_1_RST;

	au_writel(0x8000, PB1000_MDR); /* clear pcmcia interrupt */
	au_sync_delay(100);
	au_writel(0x4000, PB1000_MDR); /* enable pcmcia interrupt */
	au_sync();

	pcr \|= SET_VCC_VPP(VCC_HIZ,VPP_HIZ,0);
	pcr \|= SET_VCC_VPP(VCC_HIZ,VPP_HIZ,1);
	au_writel(pcr, PB1000_PCR);
	au_sync_delay(20);

	return PCMCIA_NUM_SOCKS;

	#else /* fixme -- take care of the Pb1500 at some point */

	u16 pcr;
	pcr = au_readw(PCMCIA_BOARD_REG) & ~0xf; /* turn off power */
	pcr &= ~(PC_DEASSERT_RST \| PC_DRV_EN);
	au_writew(pcr, PCMCIA_BOARD_REG);
	au_sync_delay(500);
	return PCMCIA_NUM_SOCKS;
	#endif
	}

	static int pb1x00_pcmcia_shutdown(void)
	{
	#ifdef CONFIG_MIPS_PB1000
	u16 pcr;
	pcr = PCR_SLOT_0_RST \| PCR_SLOT_1_RST;
	pcr \|= SET_VCC_VPP(VCC_HIZ,VPP_HIZ,0);
	pcr \|= SET_VCC_VPP(VCC_HIZ,VPP_HIZ,1);
	au_writel(pcr, PB1000_PCR);
	au_sync_delay(20);
	return 0;
	#else
	u16 pcr;
	pcr = au_readw(PCMCIA_BOARD_REG) & ~0xf; /* turn off power */
	pcr &= ~(PC_DEASSERT_RST \| PC_DRV_EN);
	au_writew(pcr, PCMCIA_BOARD_REG);
	au_sync_delay(2);
	return 0;
	#endif
	}

	static int
	pb1x00_pcmcia_socket_state(unsigned sock, struct pcmcia_state *state)
	{
	u32 inserted0, inserted1;
	u16 vs0, vs1;

	#ifdef CONFIG_MIPS_PB1000
	vs0 = vs1 = (u16)au_readl(PB1000_ACR1);
	inserted0 = !(vs0 & (ACR1_SLOT_0_CD1 \| ACR1_SLOT_0_CD2));
	inserted1 = !(vs1 & (ACR1_SLOT_1_CD1 \| ACR1_SLOT_1_CD2));
	vs0 = (vs0 >> 4) & 0x3;
	vs1 = (vs1 >> 12) & 0x3;
	#else
	vs0 = (au_readw(BOARD_STATUS_REG) >> 4) & 0x3;
	#ifdef CONFIG_MIPS_PB1500
	inserted0 = !((au_readl(GPIO2_PINSTATE) >> 1) & 0x1); /* gpio 201 */
	#else /* Pb1100 */
	inserted0 = !((au_readl(SYS_PINSTATERD) >> 9) & 0x1); /* gpio 9 */
	#endif
	inserted1 = 0;
	#endif

	state->ready = 0;
	state->vs_Xv = 0;
	state->vs_3v = 0;
	state->detect = 0;

	if (sock == 0) {
	if (inserted0) {
	switch (vs0) {
	case 0:
	case 2:
	state->vs_3v=1;
	break;
	case 3: /* 5V */
	break;
	default:
	/* return without setting 'detect' */
	printk(KERN_ERR "pb1x00 bad VS (%d)\n",
	vs0);
	return 0;
	}
	state->detect = 1;
	}
	}
	else {
	if (inserted1) {
	switch (vs1) {
	case 0:
	case 2:
	state->vs_3v=1;
	break;
	case 3: /* 5V */
	break;
	default:
	/* return without setting 'detect' */
	printk(KERN_ERR "pb1x00 bad VS (%d)\n",
	vs1);
	return 0;
	}
	state->detect = 1;
	}
	}

	if (state->detect) {
	state->ready = 1;
	}

	state->bvd1=1;
	state->bvd2=1;
	state->wrprot=0;
	return 1;
	}


	static int pb1x00_pcmcia_get_irq_info(struct pcmcia_irq_info *info)
	{

	if(info->sock > PCMCIA_MAX_SOCK) return -1;

	/*
	* Even in the case of the Pb1000, both sockets are connected
	* to the same irq line.
	*/
	info->irq = PCMCIA_IRQ;

	return 0;
	}


	static int
	pb1x00_pcmcia_configure_socket(const struct pcmcia_configure *configure)
	{
	u16 pcr;

	if(configure->sock > PCMCIA_MAX_SOCK) return -1;

	#ifdef CONFIG_MIPS_PB1000
	pcr = au_readl(PB1000_PCR);

	if (configure->sock == 0) {
	pcr &= ~(PCR_SLOT_0_VCC0 \| PCR_SLOT_0_VCC1 \|
	PCR_SLOT_0_VPP0 \| PCR_SLOT_0_VPP1);
	}
	else {
	pcr &= ~(PCR_SLOT_1_VCC0 \| PCR_SLOT_1_VCC1 \|
	PCR_SLOT_1_VPP0 \| PCR_SLOT_1_VPP1);
	}

	pcr &= ~PCR_SLOT_0_RST;
	debug("Vcc %dV Vpp %dV, pcr %x\n",
	configure->vcc, configure->vpp, pcr);
	switch(configure->vcc){
	case 0: /* Vcc 0 */
	switch(configure->vpp) {
	case 0:
	pcr \|= SET_VCC_VPP(VCC_HIZ,VPP_GND,
	configure->sock);
	break;
	case 12:
	pcr \|= SET_VCC_VPP(VCC_HIZ,VPP_12V,
	configure->sock);
	break;
	case 50:
	pcr \|= SET_VCC_VPP(VCC_HIZ,VPP_5V,
	configure->sock);
	break;
	case 33:
	pcr \|= SET_VCC_VPP(VCC_HIZ,VPP_3V,
	configure->sock);
	break;
	default:
	pcr \|= SET_VCC_VPP(VCC_HIZ,VPP_HIZ,
	configure->sock);
	printk("%s: bad Vcc/Vpp (%d:%d)\n",
	__FUNCTION__,
	configure->vcc,
	configure->vpp);
	break;
	}
	break;
	case 50: /* Vcc 5V */
	switch(configure->vpp) {
	case 0:
	pcr \|= SET_VCC_VPP(VCC_5V,VPP_GND,
	configure->sock);
	break;
	case 50:
	pcr \|= SET_VCC_VPP(VCC_5V,VPP_5V,
	configure->sock);
	break;
	case 12:
	pcr \|= SET_VCC_VPP(VCC_5V,VPP_12V,
	configure->sock);
	break;
	case 33:
	pcr \|= SET_VCC_VPP(VCC_5V,VPP_3V,
	configure->sock);
	break;
	default:
	pcr \|= SET_VCC_VPP(VCC_HIZ,VPP_HIZ,
	configure->sock);
	printk("%s: bad Vcc/Vpp (%d:%d)\n",
	__FUNCTION__,
	configure->vcc,
	configure->vpp);
	break;
	}
	break;
	case 33: /* Vcc 3.3V */
	switch(configure->vpp) {
	case 0:
	pcr \|= SET_VCC_VPP(VCC_3V,VPP_GND,
	configure->sock);
	break;
	case 50:
	pcr \|= SET_VCC_VPP(VCC_3V,VPP_5V,
	configure->sock);
	break;
	case 12:
	pcr \|= SET_VCC_VPP(VCC_3V,VPP_12V,
	configure->sock);
	break;
	case 33:
	pcr \|= SET_VCC_VPP(VCC_3V,VPP_3V,
	configure->sock);
	break;
	default:
	pcr \|= SET_VCC_VPP(VCC_HIZ,VPP_HIZ,
	configure->sock);
	printk("%s: bad Vcc/Vpp (%d:%d)\n",
	__FUNCTION__,
	configure->vcc,
	configure->vpp);
	break;
	}
	break;
	default: /* what's this ? */
	pcr \|= SET_VCC_VPP(VCC_HIZ,VPP_HIZ,configure->sock);
	printk(KERN_ERR "%s: bad Vcc %d\n",
	__FUNCTION__, configure->vcc);
	break;
	}

	if (configure->sock == 0) {
	pcr &= ~(PCR_SLOT_0_RST);
	if (configure->reset)
	pcr \|= PCR_SLOT_0_RST;
	}
	else {
	pcr &= ~(PCR_SLOT_1_RST);
	if (configure->reset)
	pcr \|= PCR_SLOT_1_RST;
	}
	au_writel(pcr, PB1000_PCR);
	au_sync_delay(300);

	#else

	pcr = au_readw(PCMCIA_BOARD_REG) & ~0xf;

	debug("Vcc %dV Vpp %dV, pcr %x, reset %d\n",
	configure->vcc, configure->vpp, pcr, configure->reset);


	switch(configure->vcc){
	case 0: /* Vcc 0 */
	pcr \|= SET_VCC_VPP(0,0);
	break;
	case 50: /* Vcc 5V */
	switch(configure->vpp) {
	case 0:
	pcr \|= SET_VCC_VPP(2,0);
	break;
	case 50:
	pcr \|= SET_VCC_VPP(2,1);
	break;
	case 12:
	pcr \|= SET_VCC_VPP(2,2);
	break;
	case 33:
	default:
	pcr \|= SET_VCC_VPP(0,0);
	printk("%s: bad Vcc/Vpp (%d:%d)\n",
	__FUNCTION__,
	configure->vcc,
	configure->vpp);
	break;
	}
	break;
	case 33: /* Vcc 3.3V */
	switch(configure->vpp) {
	case 0:
	pcr \|= SET_VCC_VPP(1,0);
	break;
	case 12:
	pcr \|= SET_VCC_VPP(1,2);
	break;
	case 33:
	pcr \|= SET_VCC_VPP(1,1);
	break;
	case 50:
	default:
	pcr \|= SET_VCC_VPP(0,0);
	printk("%s: bad Vcc/Vpp (%d:%d)\n",
	__FUNCTION__,
	configure->vcc,
	configure->vpp);
	break;
	}
	break;
	default: /* what's this ? */
	pcr \|= SET_VCC_VPP(0,0);
	printk(KERN_ERR "%s: bad Vcc %d\n",
	__FUNCTION__, configure->vcc);
	break;
	}

	au_writew(pcr, PCMCIA_BOARD_REG);
	au_sync_delay(300);

	if (!configure->reset) {
	pcr \|= PC_DRV_EN;
	au_writew(pcr, PCMCIA_BOARD_REG);
	au_sync_delay(100);
	pcr \|= PC_DEASSERT_RST;
	au_writew(pcr, PCMCIA_BOARD_REG);
	au_sync_delay(100);
	}
	else {
	pcr &= ~(PC_DEASSERT_RST \| PC_DRV_EN);
	au_writew(pcr, PCMCIA_BOARD_REG);
	au_sync_delay(100);
	}
	#endif
	return 0;
	}


	struct pcmcia_low_level pb1x00_pcmcia_ops = {
	pb1x00_pcmcia_init,
	pb1x00_pcmcia_shutdown,
	pb1x00_pcmcia_socket_state,
	pb1x00_pcmcia_get_irq_info,
	pb1x00_pcmcia_configure_socket
	};