r8169: adjust the RxConfig settings.
Set the init value before reset in probe function. And then just
modify the relative bits and keep the init settings.
For 8110S, 8110SB, and 8110SC series, the initial value of RxConfig
needs to be set after the tx/rx is enabled.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Acked-by: Francois Romieu <romieu@fr.zoreil.com>
diff --git a/drivers/net/r8169.c b/drivers/net/r8169.c
index 6d7f686..3ddd339 100644
--- a/drivers/net/r8169.c
+++ b/drivers/net/r8169.c
@@ -286,7 +286,6 @@
#define RXCFG_DMA_SHIFT 8
/* Unlimited maximum PCI burst. */
#define RX_DMA_BURST (7 << RXCFG_DMA_SHIFT)
-#define RTL_RX_CONFIG_MASK 0xff7e1880u
RxMissed = 0x4c,
Cfg9346 = 0x50,
@@ -728,8 +727,6 @@
static void rtl8169_rx_clear(struct rtl8169_private *tp);
static int rtl8169_poll(struct napi_struct *napi, int budget);
-static const unsigned int rtl8169_rx_config = RX_FIFO_THRESH | RX_DMA_BURST;
-
static u32 ocp_read(struct rtl8169_private *tp, u8 mask, u16 reg)
{
void __iomem *ioaddr = tp->mmio_addr;
@@ -3503,6 +3500,42 @@
}
}
+static void rtl_init_rxcfg(struct rtl8169_private *tp)
+{
+ void __iomem *ioaddr = tp->mmio_addr;
+
+ switch (tp->mac_version) {
+ case RTL_GIGA_MAC_VER_01:
+ case RTL_GIGA_MAC_VER_02:
+ case RTL_GIGA_MAC_VER_03:
+ case RTL_GIGA_MAC_VER_04:
+ case RTL_GIGA_MAC_VER_05:
+ case RTL_GIGA_MAC_VER_06:
+ case RTL_GIGA_MAC_VER_10:
+ case RTL_GIGA_MAC_VER_11:
+ case RTL_GIGA_MAC_VER_12:
+ case RTL_GIGA_MAC_VER_13:
+ case RTL_GIGA_MAC_VER_14:
+ case RTL_GIGA_MAC_VER_15:
+ case RTL_GIGA_MAC_VER_16:
+ case RTL_GIGA_MAC_VER_17:
+ RTL_W32(RxConfig, RX_FIFO_THRESH | RX_DMA_BURST);
+ break;
+ case RTL_GIGA_MAC_VER_18:
+ case RTL_GIGA_MAC_VER_19:
+ case RTL_GIGA_MAC_VER_20:
+ case RTL_GIGA_MAC_VER_21:
+ case RTL_GIGA_MAC_VER_22:
+ case RTL_GIGA_MAC_VER_23:
+ case RTL_GIGA_MAC_VER_24:
+ RTL_W32(RxConfig, RX128_INT_EN | RX_MULTI_EN | RX_DMA_BURST);
+ break;
+ default:
+ RTL_W32(RxConfig, RX128_INT_EN | RX_DMA_BURST);
+ break;
+ }
+}
+
static void rtl8169_init_ring_indexes(struct rtl8169_private *tp)
{
tp->dirty_tx = tp->dirty_rx = tp->cur_tx = tp->cur_rx = 0;
@@ -3630,6 +3663,11 @@
if (!pci_is_pcie(pdev))
netif_info(tp, probe, dev, "not PCI Express\n");
+ /* Identify chip attached to board */
+ rtl8169_get_mac_version(tp, dev, cfg->default_ver);
+
+ rtl_init_rxcfg(tp);
+
RTL_W16(IntrMask, 0x0000);
rtl_hw_reset(tp);
@@ -3638,9 +3676,6 @@
pci_set_master(pdev);
- /* Identify chip attached to board */
- rtl8169_get_mac_version(tp, dev, cfg->default_ver);
-
/*
* Pretend we are using VLANs; This bypasses a nasty bug where
* Interrupts stop flowing on high load on 8110SCd controllers.
@@ -3943,10 +3978,6 @@
static void rtl_set_rx_tx_config_registers(struct rtl8169_private *tp)
{
void __iomem *ioaddr = tp->mmio_addr;
- u32 cfg = rtl8169_rx_config;
-
- cfg |= (RTL_R32(RxConfig) & RTL_RX_CONFIG_MASK);
- RTL_W32(RxConfig, cfg);
/* Set DMA burst size and Interframe Gap Time */
RTL_W32(TxConfig, (TX_DMA_BURST << TxDMAShift) |
@@ -4034,6 +4065,8 @@
tp->mac_version == RTL_GIGA_MAC_VER_04)
RTL_W8(ChipCmd, CmdTxEnb | CmdRxEnb);
+ rtl_init_rxcfg(tp);
+
RTL_W8(EarlyTxThres, NoEarlyTx);
rtl_set_rx_max_size(ioaddr, rx_buf_sz);
@@ -5553,8 +5586,7 @@
spin_lock_irqsave(&tp->lock, flags);
- tmp = rtl8169_rx_config | rx_mode |
- (RTL_R32(RxConfig) & RTL_RX_CONFIG_MASK);
+ tmp = RTL_R32(RxConfig) | rx_mode;
if (tp->mac_version > RTL_GIGA_MAC_VER_06) {
u32 data = mc_filter[0];