powerpc, of_serial: Endianness issues setting up the serial ports
The speed and clock of the serial ports is retrieved from the device
tree in both the PowerPC legacy serial code and the Open Firmware serial
driver, therefore they need to handle the fact that the device tree is
always big endian, while the CPU may not be.
Also fix other device tree references in the legacy serial code.
Signed-off-by: Ian Munsie <imunsie@au1.ibm.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
diff --git a/arch/powerpc/kernel/legacy_serial.c b/arch/powerpc/kernel/legacy_serial.c
index c1fd0f9..c834757 100644
--- a/arch/powerpc/kernel/legacy_serial.c
+++ b/arch/powerpc/kernel/legacy_serial.c
@@ -52,14 +52,14 @@
phys_addr_t taddr, unsigned long irq,
upf_t flags, int irq_check_parent)
{
- const u32 *clk, *spd;
+ const __be32 *clk, *spd;
u32 clock = BASE_BAUD * 16;
int index;
/* get clock freq. if present */
clk = of_get_property(np, "clock-frequency", NULL);
if (clk && *clk)
- clock = *clk;
+ clock = be32_to_cpup(clk);
/* get default speed if present */
spd = of_get_property(np, "current-speed", NULL);
@@ -109,7 +109,7 @@
legacy_serial_infos[index].taddr = taddr;
legacy_serial_infos[index].np = of_node_get(np);
legacy_serial_infos[index].clock = clock;
- legacy_serial_infos[index].speed = spd ? *spd : 0;
+ legacy_serial_infos[index].speed = spd ? be32_to_cpup(spd) : 0;
legacy_serial_infos[index].irq_check_parent = irq_check_parent;
printk(KERN_DEBUG "Found legacy serial port %d for %s\n",
@@ -168,7 +168,7 @@
static int __init add_legacy_isa_port(struct device_node *np,
struct device_node *isa_brg)
{
- const u32 *reg;
+ const __be32 *reg;
const char *typep;
int index = -1;
u64 taddr;
@@ -181,7 +181,7 @@
return -1;
/* Verify it's an IO port, we don't support anything else */
- if (!(reg[0] & 0x00000001))
+ if (!(be32_to_cpu(reg[0]) & 0x00000001))
return -1;
/* Now look for an "ibm,aix-loc" property that gives us ordering
@@ -202,7 +202,7 @@
taddr = 0;
/* Add port, irq will be dealt with later */
- return add_legacy_port(np, index, UPIO_PORT, reg[1], taddr,
+ return add_legacy_port(np, index, UPIO_PORT, be32_to_cpu(reg[1]), taddr,
NO_IRQ, UPF_BOOT_AUTOCONF, 0);
}
@@ -251,9 +251,9 @@
* we get to their "reg" property
*/
if (np != pci_dev) {
- const u32 *reg = of_get_property(np, "reg", NULL);
- if (reg && (*reg < 4))
- index = lindex = *reg;
+ const __be32 *reg = of_get_property(np, "reg", NULL);
+ if (reg && (be32_to_cpup(reg) < 4))
+ index = lindex = be32_to_cpup(reg);
}
/* Local index means it's the Nth port in the PCI chip. Unfortunately
@@ -507,7 +507,7 @@
struct device_node *prom_stdout = NULL;
int i, speed = 0, offset = 0;
const char *name;
- const u32 *spd;
+ const __be32 *spd;
DBG(" -> check_legacy_serial_console()\n");
@@ -547,7 +547,7 @@
}
spd = of_get_property(prom_stdout, "current-speed", NULL);
if (spd)
- speed = *spd;
+ speed = be32_to_cpup(spd);
if (strcmp(name, "serial") != 0)
goto not_found;
diff --git a/drivers/serial/of_serial.c b/drivers/serial/of_serial.c
index 2af8fd1..17849dc 100644
--- a/drivers/serial/of_serial.c
+++ b/drivers/serial/of_serial.c
@@ -31,8 +31,8 @@
{
struct resource resource;
struct device_node *np = ofdev->dev.of_node;
- const unsigned int *clk, *spd;
- const u32 *prop;
+ const __be32 *clk, *spd;
+ const __be32 *prop;
int ret, prop_size;
memset(port, 0, sizeof *port);
@@ -55,23 +55,23 @@
/* Check for shifted address mapping */
prop = of_get_property(np, "reg-offset", &prop_size);
if (prop && (prop_size == sizeof(u32)))
- port->mapbase += *prop;
+ port->mapbase += be32_to_cpup(prop);
/* Check for registers offset within the devices address range */
prop = of_get_property(np, "reg-shift", &prop_size);
if (prop && (prop_size == sizeof(u32)))
- port->regshift = *prop;
+ port->regshift = be32_to_cpup(prop);
port->irq = irq_of_parse_and_map(np, 0);
port->iotype = UPIO_MEM;
port->type = type;
- port->uartclk = *clk;
+ port->uartclk = be32_to_cpup(clk);
port->flags = UPF_SHARE_IRQ | UPF_BOOT_AUTOCONF | UPF_IOREMAP
| UPF_FIXED_PORT | UPF_FIXED_TYPE;
port->dev = &ofdev->dev;
/* If current-speed was set, then try not to change it. */
if (spd)
- port->custom_divisor = *clk / (16 * (*spd));
+ port->custom_divisor = be32_to_cpup(clk) / (16 * (be32_to_cpup(spd)));
return 0;
}