pxa2xx_spi: fix chip_info defaults and documentation.
Make the chip info structure data optional by providing reasonable
defaults. Improve corresponding documentation, and highlight the drawback
of not providing explicit chipselect control.
DMA can determine appropriate dma_burst_size and thresholds automatically
so use DMA even if dma_burst_size is not specified.
Signed-off-by: Vernon Sauder <VernonInHand@gmail.com>
Reviewed-by: Ned Forrester <nforrester@whoi.edu>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
diff --git a/Documentation/spi/pxa2xx b/Documentation/spi/pxa2xx
index bbe8dee..6bb916d 100644
--- a/Documentation/spi/pxa2xx
+++ b/Documentation/spi/pxa2xx
@@ -96,7 +96,7 @@
information via the structure "pxa2xx_spi_chip" found in
"arch/arm/mach-pxa/include/mach/pxa2xx_spi.h". The pxa2xx_spi master controller driver
will uses the configuration whenever the driver communicates with the slave
-device.
+device. All fields are optional.
struct pxa2xx_spi_chip {
u8 tx_threshold;
@@ -112,14 +112,17 @@
performance of pxa2xx_spi driver and misconfiguration will result in rx
fifo overruns (especially in PIO mode transfers). Good default values are
- .tx_threshold = 12,
- .rx_threshold = 4,
+ .tx_threshold = 8,
+ .rx_threshold = 8,
+
+The range is 1 to 16 where zero indicates "use default".
The "pxa2xx_spi_chip.dma_burst_size" field is used to configure PXA2xx DMA
engine and is related the "spi_device.bits_per_word" field. Read and understand
the PXA2xx "Developer Manual" sections on the DMA controller and SSP Controllers
to determine the correct value. An SSP configured for byte-wide transfers would
-use a value of 8.
+use a value of 8. The driver will determine a reasonable default if
+dma_burst_size == 0.
The "pxa2xx_spi_chip.timeout" fields is used to efficiently handle
trailing bytes in the SSP receiver fifo. The correct value for this field is
@@ -137,7 +140,13 @@
NULL, the pxa2xx_spi master controller driver assumes that the SSP port is
configured to use SSPFRM instead.
-NSSP SALVE SAMPLE
+NOTE: the SPI driver cannot control the chip select if SSPFRM is used, so the
+chipselect is dropped after each spi_transfer. Most devices need chip select
+asserted around the complete message. Use SSPFRM as a GPIO (through cs_control)
+to accomodate these chips.
+
+
+NSSP SLAVE SAMPLE
-----------------
The pxa2xx_spi_chip structure is passed to the pxa2xx_spi driver in the
"spi_board_info.controller_data" field. Below is a sample configuration using
@@ -206,18 +215,21 @@
DMA and PIO I/O Support
-----------------------
-The pxa2xx_spi driver support both DMA and interrupt driven PIO message
-transfers. The driver defaults to PIO mode and DMA transfers must enabled by
-setting the "enable_dma" flag in the "pxa2xx_spi_master" structure and
-ensuring that the "pxa2xx_spi_chip.dma_burst_size" field is non-zero. The DMA
-mode support both coherent and stream based DMA mappings.
+The pxa2xx_spi driver supports both DMA and interrupt driven PIO message
+transfers. The driver defaults to PIO mode and DMA transfers must be enabled
+by setting the "enable_dma" flag in the "pxa2xx_spi_master" structure. The DMA
+mode supports both coherent and stream based DMA mappings.
The following logic is used to determine the type of I/O to be used on
a per "spi_transfer" basis:
-if !enable_dma or dma_burst_size == 0 then
+if !enable_dma then
always use PIO transfers
+if spi_message.len > 8191 then
+ print "rate limited" warning
+ use PIO transfers
+
if spi_message.is_dma_mapped and rx_dma_buf != 0 and tx_dma_buf != 0 then
use coherent DMA mode
diff --git a/drivers/spi/pxa2xx_spi.c b/drivers/spi/pxa2xx_spi.c
index 59ae3ed..dae87b1 100644
--- a/drivers/spi/pxa2xx_spi.c
+++ b/drivers/spi/pxa2xx_spi.c
@@ -47,6 +47,10 @@
#define MAX_BUSES 3
+#define RX_THRESH_DFLT 8
+#define TX_THRESH_DFLT 8
+#define TIMOUT_DFLT 1000
+
#define DMA_INT_MASK (DCSR_ENDINTR | DCSR_STARTINTR | DCSR_BUSERR)
#define RESET_DMA_CHANNEL (DCSR_NODESC | DMA_INT_MASK)
#define IS_DMA_ALIGNED(x) ((((u32)(x)) & 0x07) == 0)
@@ -1171,6 +1175,8 @@
struct driver_data *drv_data = spi_master_get_devdata(spi->master);
struct ssp_device *ssp = drv_data->ssp;
unsigned int clk_div;
+ uint tx_thres = TX_THRESH_DFLT;
+ uint rx_thres = RX_THRESH_DFLT;
if (!spi->bits_per_word)
spi->bits_per_word = 8;
@@ -1209,8 +1215,7 @@
chip->cs_control = null_cs_control;
chip->enable_dma = 0;
- chip->timeout = 1000;
- chip->threshold = SSCR1_RxTresh(1) | SSCR1_TxTresh(1);
+ chip->timeout = TIMOUT_DFLT;
chip->dma_burst_size = drv_data->master_info->enable_dma ?
DCMD_BURST8 : 0;
}
@@ -1224,22 +1229,21 @@
if (chip_info) {
if (chip_info->cs_control)
chip->cs_control = chip_info->cs_control;
-
- chip->timeout = chip_info->timeout;
-
- chip->threshold = (SSCR1_RxTresh(chip_info->rx_threshold) &
- SSCR1_RFT) |
- (SSCR1_TxTresh(chip_info->tx_threshold) &
- SSCR1_TFT);
-
- chip->enable_dma = chip_info->dma_burst_size != 0
- && drv_data->master_info->enable_dma;
+ if (chip_info->timeout)
+ chip->timeout = chip_info->timeout;
+ if (chip_info->tx_threshold)
+ tx_thres = chip_info->tx_threshold;
+ if (chip_info->rx_threshold)
+ rx_thres = chip_info->rx_threshold;
+ chip->enable_dma = drv_data->master_info->enable_dma;
chip->dma_threshold = 0;
-
if (chip_info->enable_loopback)
chip->cr1 = SSCR1_LBM;
}
+ chip->threshold = (SSCR1_RxTresh(rx_thres) & SSCR1_RFT) |
+ (SSCR1_TxTresh(tx_thres) & SSCR1_TFT);
+
/* set dma burst and threshold outside of chip_info path so that if
* chip_info goes away after setting chip->enable_dma, the
* burst and threshold can still respond to changes in bits_per_word */
@@ -1268,17 +1272,19 @@
/* NOTE: PXA25x_SSP _could_ use external clocking ... */
if (drv_data->ssp_type != PXA25x_SSP)
- dev_dbg(&spi->dev, "%d bits/word, %ld Hz, mode %d\n",
+ dev_dbg(&spi->dev, "%d bits/word, %ld Hz, mode %d, %s\n",
spi->bits_per_word,
clk_get_rate(ssp->clk)
/ (1 + ((chip->cr0 & SSCR0_SCR) >> 8)),
- spi->mode & 0x3);
+ spi->mode & 0x3,
+ chip->enable_dma ? "DMA" : "PIO");
else
- dev_dbg(&spi->dev, "%d bits/word, %ld Hz, mode %d\n",
+ dev_dbg(&spi->dev, "%d bits/word, %ld Hz, mode %d, %s\n",
spi->bits_per_word,
- clk_get_rate(ssp->clk)
+ clk_get_rate(ssp->clk) / 2
/ (1 + ((chip->cr0 & SSCR0_SCR) >> 8)),
- spi->mode & 0x3);
+ spi->mode & 0x3,
+ chip->enable_dma ? "DMA" : "PIO");
if (spi->bits_per_word <= 8) {
chip->n_bytes = 1;
@@ -1498,7 +1504,9 @@
/* Load default SSP configuration */
write_SSCR0(0, drv_data->ioaddr);
- write_SSCR1(SSCR1_RxTresh(4) | SSCR1_TxTresh(12), drv_data->ioaddr);
+ write_SSCR1(SSCR1_RxTresh(RX_THRESH_DFLT) |
+ SSCR1_TxTresh(TX_THRESH_DFLT),
+ drv_data->ioaddr);
write_SSCR0(SSCR0_SerClkDiv(2)
| SSCR0_Motorola
| SSCR0_DataSize(8),