Bluetooth: Increase timeout for legacy pairing from 10 seconds to 40 seconds.
Legacy pairing is a bit of a problem because on the incoming end it is
impossible to know pairing has begun:
2009-09-18 18:29:24.115692 > HCI Event: Connect Request (0x04) plen 10
bdaddr 00:23:D4:04:51:7A class 0x58020c type ACL
2009-09-18 18:29:24.115966 < HCI Command: Accept Connection Request (0x01|0x0009) plen 7
bdaddr 00:23:D4:04:51:7A role 0x00
Role: Master
2009-09-18 18:29:24.117065 > HCI Event: Command Status (0x0f) plen 4
Accept Connection Request (0x01|0x0009) status 0x00 ncmd 1
2009-09-18 18:29:24.282928 > HCI Event: Role Change (0x12) plen 8
status 0x00 bdaddr 00:23:D4:04:51:7A role 0x00
Role: Master
2009-09-18 18:29:24.291534 > HCI Event: Connect Complete (0x03) plen 11
status 0x00 handle 1 bdaddr 00:23:D4:04:51:7A type ACL encrypt 0x00
2009-09-18 18:29:24.291839 < HCI Command: Read Remote Supported Features (0x01|0x001b) plen 2
handle 1
2009-09-18 18:29:24.292144 > HCI Event: Page Scan Repetition Mode Change (0x20) plen 7
bdaddr 00:23:D4:04:51:7A mode 1
2009-09-18 18:29:24.293823 > HCI Event: Command Status (0x0f) plen 4
Read Remote Supported Features (0x01|0x001b) status 0x00 ncmd 1
2009-09-18 18:29:24.303588 > HCI Event: Max Slots Change (0x1b) plen 3
handle 1 slots 5
2009-09-18 18:29:24.309448 > HCI Event: Read Remote Supported Features (0x0b) plen 11
status 0x00 handle 1
Features: 0xff 0xff 0x2d 0xfe 0x9b 0xff 0x79 0x83
2009-09-18 18:29:24.345916 < HCI Command: Remote Name Request (0x01|0x0019) plen 10
bdaddr 00:23:D4:04:51:7A mode 2 clkoffset 0x0000
2009-09-18 18:29:24.346923 > HCI Event: Command Status (0x0f) plen 4
Remote Name Request (0x01|0x0019) status 0x00 ncmd 1
2009-09-18 18:29:24.375793 > HCI Event: Remote Name Req Complete (0x07) plen 255
status 0x00 bdaddr 00:23:D4:04:51:7A name 'test'
2009-09-18 18:29:34.332190 < HCI Command: Disconnect (0x01|0x0006) plen 3
handle 1 reason 0x13
There are some mainline patches such as "Add different pairing timeout for
Legacy Pairing" but they do not address the HCI sequence above.
I think the real solution is to avoid using CreateBond(), and instead make
the profile connection immediately. This way both sides will use a longer
timeout because there is a higher level connection in progress, and we will
not end up with the useless HCI sequence above.
Signed-off-by: Nick Pelly <npelly@google.com>
diff --git a/include/net/bluetooth/hci_core.h b/include/net/bluetooth/hci_core.h
index daefaac..5203748 100644
--- a/include/net/bluetooth/hci_core.h
+++ b/include/net/bluetooth/hci_core.h
@@ -597,7 +597,7 @@
if (conn->state == BT_CONNECTED) {
timeo = msecs_to_jiffies(conn->disc_timeout);
if (!conn->out)
- timeo *= 2;
+ timeo *= 20;
} else {
timeo = msecs_to_jiffies(10);
}