arch/arm/mach-msm/board-qsd8x50.c

/* Copyright (c) 2008-2009, Code Aurora Forum. All rights reserved.
 *
 * This program is free software; you can redistribute it and/or modify
 * it under the terms of the GNU General Public License version 2 and
 * only version 2 as published by the Free Software Foundation.
 *
 * This program is distributed in the hope that it will be useful,
 * but WITHOUT ANY WARRANTY; without even the implied warranty of
 * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
 * GNU General Public License for more details.
 *
 * You should have received a copy of the GNU General Public License
 * along with this program; if not, write to the Free Software
 * Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston, MA
 * 02110-1301, USA.
 */

#include <linux/kernel.h>
#include <linux/irq.h>
#include <linux/gpio.h>
#include <linux/platform_device.h>
#include <linux/delay.h>

#include <asm/mach-types.h>
#include <asm/mach/arch.h>
#include <asm/io.h>
#include <asm/setup.h>

#include <mach/board.h>
#include <mach/irqs.h>
#include <mach/sirc.h>
#include <mach/gpio.h>

#include "devices.h"

extern struct sys_timer msm_timer;

static struct msm_gpio uart3_config_data[] = {
	{ GPIO_CFG(86, 1, GPIO_INPUT,   GPIO_PULL_DOWN, GPIO_2MA), "UART2_Rx"},
	{ GPIO_CFG(87, 1, GPIO_OUTPUT,  GPIO_PULL_DOWN, GPIO_2MA), "UART2_Tx"},
};

static struct platform_device *devices[] __initdata = {
	&msm_device_uart3,
};

static void msm8x50_init_uart3(void)
{
	msm_gpios_request_enable(uart3_config_data,
				ARRAY_SIZE(uart3_config_data));
}

static void __init qsd8x50_map_io(void)
{
	msm_map_qsd8x50_io();
	msm_clock_init(msm_clocks_8x50, msm_num_clocks_8x50);
}

static void __init qsd8x50_init_irq(void)
{
	msm_init_irq();
	msm_init_sirc();
}

static void __init qsd8x50_init(void)
{
	msm8x50_init_uart3();
	platform_add_devices(devices, ARRAY_SIZE(devices));
}

MACHINE_START(QSD8X50_SURF, "QCT QSD8X50 SURF")
#ifdef CONFIG_MSM_DEBUG_UART
	.phys_io  = MSM_DEBUG_UART_PHYS,
	.io_pg_offst = ((MSM_DEBUG_UART_BASE) >> 18) & 0xfffc,
#endif
	.boot_params = PHYS_OFFSET + 0x100,
	.map_io = qsd8x50_map_io,
	.init_irq = qsd8x50_init_irq,
	.init_machine = qsd8x50_init,
	.timer = &msm_timer,
MACHINE_END

MACHINE_START(QSD8X50A_ST1_5, "QCT QSD8X50A ST1.5")
#ifdef CONFIG_MSM_DEBUG_UART
	.phys_io  = MSM_DEBUG_UART_PHYS,
	.io_pg_offst = ((MSM_DEBUG_UART_BASE) >> 18) & 0xfffc,
#endif
	.boot_params = PHYS_OFFSET + 0x100,
	.map_io = qsd8x50_map_io,
	.init_irq = qsd8x50_init_irq,
	.init_machine = qsd8x50_init,
	.timer = &msm_timer,
MACHINE_END