| /* |
| * Version 2.24 |
| * |
| * AMD 755/756/766/8111 and nVidia nForce/2/2s/3/3s/CK804/MCP04 |
| * IDE driver for Linux. |
| * |
| * Copyright (c) 2000-2002 Vojtech Pavlik |
| * Copyright (c) 2007 Bartlomiej Zolnierkiewicz |
| * |
| * Based on the work of: |
| * Andre Hedrick |
| */ |
| |
| /* |
| * This program is free software; you can redistribute it and/or modify it |
| * under the terms of the GNU General Public License version 2 as published by |
| * the Free Software Foundation. |
| */ |
| |
| #include <linux/module.h> |
| #include <linux/kernel.h> |
| #include <linux/ioport.h> |
| #include <linux/blkdev.h> |
| #include <linux/pci.h> |
| #include <linux/init.h> |
| #include <linux/ide.h> |
| #include <asm/io.h> |
| |
| #include "ide-timing.h" |
| |
| #define AMD_IDE_CONFIG (0x01 + amd_config->base) |
| #define AMD_CABLE_DETECT (0x02 + amd_config->base) |
| #define AMD_DRIVE_TIMING (0x08 + amd_config->base) |
| #define AMD_8BIT_TIMING (0x0e + amd_config->base) |
| #define AMD_ADDRESS_SETUP (0x0c + amd_config->base) |
| #define AMD_UDMA_TIMING (0x10 + amd_config->base) |
| |
| #define AMD_CHECK_SWDMA 0x08 |
| #define AMD_BAD_SWDMA 0x10 |
| #define AMD_BAD_FIFO 0x20 |
| #define AMD_CHECK_SERENADE 0x40 |
| |
| /* |
| * AMD SouthBridge chips. |
| */ |
| |
| static struct amd_ide_chip { |
| unsigned short id; |
| u8 base; |
| u8 udma_mask; |
| u8 flags; |
| } amd_ide_chips[] = { |
| { PCI_DEVICE_ID_AMD_COBRA_7401, 0x40, ATA_UDMA2, AMD_BAD_SWDMA }, |
| { PCI_DEVICE_ID_AMD_VIPER_7409, 0x40, ATA_UDMA4, AMD_CHECK_SWDMA }, |
| { PCI_DEVICE_ID_AMD_VIPER_7411, 0x40, ATA_UDMA5, AMD_BAD_FIFO }, |
| { PCI_DEVICE_ID_AMD_OPUS_7441, 0x40, ATA_UDMA5, }, |
| { PCI_DEVICE_ID_AMD_8111_IDE, 0x40, ATA_UDMA6, AMD_CHECK_SERENADE }, |
| { PCI_DEVICE_ID_NVIDIA_NFORCE_IDE, 0x50, ATA_UDMA5, }, |
| { PCI_DEVICE_ID_NVIDIA_NFORCE2_IDE, 0x50, ATA_UDMA6, }, |
| { PCI_DEVICE_ID_NVIDIA_NFORCE2S_IDE, 0x50, ATA_UDMA6, }, |
| { PCI_DEVICE_ID_NVIDIA_NFORCE2S_SATA, 0x50, ATA_UDMA6, }, |
| { PCI_DEVICE_ID_NVIDIA_NFORCE3_IDE, 0x50, ATA_UDMA6, }, |
| { PCI_DEVICE_ID_NVIDIA_NFORCE3S_IDE, 0x50, ATA_UDMA6, }, |
| { PCI_DEVICE_ID_NVIDIA_NFORCE3S_SATA, 0x50, ATA_UDMA6, }, |
| { PCI_DEVICE_ID_NVIDIA_NFORCE3S_SATA2, 0x50, ATA_UDMA6, }, |
| { PCI_DEVICE_ID_NVIDIA_NFORCE_CK804_IDE, 0x50, ATA_UDMA6, }, |
| { PCI_DEVICE_ID_NVIDIA_NFORCE_MCP04_IDE, 0x50, ATA_UDMA6, }, |
| { PCI_DEVICE_ID_NVIDIA_NFORCE_MCP51_IDE, 0x50, ATA_UDMA6, }, |
| { PCI_DEVICE_ID_NVIDIA_NFORCE_MCP55_IDE, 0x50, ATA_UDMA6, }, |
| { PCI_DEVICE_ID_NVIDIA_NFORCE_MCP61_IDE, 0x50, ATA_UDMA6, }, |
| { PCI_DEVICE_ID_NVIDIA_NFORCE_MCP65_IDE, 0x50, ATA_UDMA6, }, |
| { PCI_DEVICE_ID_NVIDIA_NFORCE_MCP67_IDE, 0x50, ATA_UDMA6, }, |
| { PCI_DEVICE_ID_NVIDIA_NFORCE_MCP73_IDE, 0x50, ATA_UDMA6, }, |
| { PCI_DEVICE_ID_NVIDIA_NFORCE_MCP77_IDE, 0x50, ATA_UDMA6, }, |
| { PCI_DEVICE_ID_AMD_CS5536_IDE, 0x40, ATA_UDMA5, }, |
| { 0 } |
| }; |
| |
| static struct amd_ide_chip *amd_config; |
| static const struct ide_port_info *amd_chipset; |
| static unsigned int amd_80w; |
| static unsigned int amd_clock; |
| |
| static char *amd_dma[] = { "16", "25", "33", "44", "66", "100", "133" }; |
| static unsigned char amd_cyc2udma[] = { 6, 6, 5, 4, 0, 1, 1, 2, 2, 3, 3, 3, 3, 3, 3, 7 }; |
| |
| /* |
| * amd_set_speed() writes timing values to the chipset registers |
| */ |
| |
| static void amd_set_speed(struct pci_dev *dev, unsigned char dn, struct ide_timing *timing) |
| { |
| unsigned char t; |
| |
| pci_read_config_byte(dev, AMD_ADDRESS_SETUP, &t); |
| t = (t & ~(3 << ((3 - dn) << 1))) | ((FIT(timing->setup, 1, 4) - 1) << ((3 - dn) << 1)); |
| pci_write_config_byte(dev, AMD_ADDRESS_SETUP, t); |
| |
| pci_write_config_byte(dev, AMD_8BIT_TIMING + (1 - (dn >> 1)), |
| ((FIT(timing->act8b, 1, 16) - 1) << 4) | (FIT(timing->rec8b, 1, 16) - 1)); |
| |
| pci_write_config_byte(dev, AMD_DRIVE_TIMING + (3 - dn), |
| ((FIT(timing->active, 1, 16) - 1) << 4) | (FIT(timing->recover, 1, 16) - 1)); |
| |
| switch (amd_config->udma_mask) { |
| case ATA_UDMA2: t = timing->udma ? (0xc0 | (FIT(timing->udma, 2, 5) - 2)) : 0x03; break; |
| case ATA_UDMA4: t = timing->udma ? (0xc0 | amd_cyc2udma[FIT(timing->udma, 2, 10)]) : 0x03; break; |
| case ATA_UDMA5: t = timing->udma ? (0xc0 | amd_cyc2udma[FIT(timing->udma, 1, 10)]) : 0x03; break; |
| case ATA_UDMA6: t = timing->udma ? (0xc0 | amd_cyc2udma[FIT(timing->udma, 1, 15)]) : 0x03; break; |
| default: return; |
| } |
| |
| pci_write_config_byte(dev, AMD_UDMA_TIMING + (3 - dn), t); |
| } |
| |
| /* |
| * amd_set_drive() computes timing values and configures the chipset |
| * to a desired transfer mode. It also can be called by upper layers. |
| */ |
| |
| static void amd_set_drive(ide_drive_t *drive, const u8 speed) |
| { |
| ide_drive_t *peer = HWIF(drive)->drives + (~drive->dn & 1); |
| struct ide_timing t, p; |
| int T, UT; |
| |
| T = 1000000000 / amd_clock; |
| UT = (amd_config->udma_mask == ATA_UDMA2) ? T : (T / 2); |
| |
| ide_timing_compute(drive, speed, &t, T, UT); |
| |
| if (peer->present) { |
| ide_timing_compute(peer, peer->current_speed, &p, T, UT); |
| ide_timing_merge(&p, &t, &t, IDE_TIMING_8BIT); |
| } |
| |
| if (speed == XFER_UDMA_5 && amd_clock <= 33333) t.udma = 1; |
| if (speed == XFER_UDMA_6 && amd_clock <= 33333) t.udma = 15; |
| |
| amd_set_speed(HWIF(drive)->pci_dev, drive->dn, &t); |
| } |
| |
| /* |
| * amd_set_pio_mode() is a callback from upper layers for PIO-only tuning. |
| */ |
| |
| static void amd_set_pio_mode(ide_drive_t *drive, const u8 pio) |
| { |
| amd_set_drive(drive, XFER_PIO_0 + pio); |
| } |
| |
| /* |
| * The initialization callback. Here we determine the IDE chip type |
| * and initialize its drive independent registers. |
| */ |
| |
| static unsigned int __devinit init_chipset_amd74xx(struct pci_dev *dev, const char *name) |
| { |
| unsigned char t; |
| unsigned int u; |
| int i; |
| |
| /* |
| * Check for bad SWDMA. |
| */ |
| |
| if (amd_config->flags & AMD_CHECK_SWDMA) { |
| if (dev->revision <= 7) |
| amd_config->flags |= AMD_BAD_SWDMA; |
| } |
| |
| /* |
| * Check 80-wire cable presence. |
| */ |
| |
| switch (amd_config->udma_mask) { |
| |
| case ATA_UDMA6: |
| case ATA_UDMA5: |
| pci_read_config_byte(dev, AMD_CABLE_DETECT, &t); |
| pci_read_config_dword(dev, AMD_UDMA_TIMING, &u); |
| amd_80w = ((t & 0x3) ? 1 : 0) | ((t & 0xc) ? 2 : 0); |
| for (i = 24; i >= 0; i -= 8) |
| if (((u >> i) & 4) && !(amd_80w & (1 << (1 - (i >> 4))))) { |
| printk(KERN_WARNING "%s: BIOS didn't set cable bits correctly. Enabling workaround.\n", |
| amd_chipset->name); |
| amd_80w |= (1 << (1 - (i >> 4))); |
| } |
| break; |
| |
| case ATA_UDMA4: |
| /* no host side cable detection */ |
| amd_80w = 0x03; |
| break; |
| } |
| |
| /* |
| * Take care of prefetch & postwrite. |
| */ |
| |
| pci_read_config_byte(dev, AMD_IDE_CONFIG, &t); |
| pci_write_config_byte(dev, AMD_IDE_CONFIG, |
| (amd_config->flags & AMD_BAD_FIFO) ? (t & 0x0f) : (t | 0xf0)); |
| |
| /* |
| * Take care of incorrectly wired Serenade mainboards. |
| */ |
| |
| if ((amd_config->flags & AMD_CHECK_SERENADE) && |
| dev->subsystem_vendor == PCI_VENDOR_ID_AMD && |
| dev->subsystem_device == PCI_DEVICE_ID_AMD_SERENADE) |
| amd_config->udma_mask = ATA_UDMA5; |
| |
| /* |
| * Determine the system bus clock. |
| */ |
| |
| amd_clock = system_bus_clock() * 1000; |
| |
| switch (amd_clock) { |
| case 33000: amd_clock = 33333; break; |
| case 37000: amd_clock = 37500; break; |
| case 41000: amd_clock = 41666; break; |
| } |
| |
| if (amd_clock < 20000 || amd_clock > 50000) { |
| printk(KERN_WARNING "%s: User given PCI clock speed impossible (%d), using 33 MHz instead.\n", |
| amd_chipset->name, amd_clock); |
| amd_clock = 33333; |
| } |
| |
| /* |
| * Print the boot message. |
| */ |
| |
| printk(KERN_INFO "%s: %s (rev %02x) UDMA%s controller\n", |
| amd_chipset->name, pci_name(dev), dev->revision, |
| amd_dma[fls(amd_config->udma_mask) - 1]); |
| |
| return dev->irq; |
| } |
| |
| static void __devinit init_hwif_amd74xx(ide_hwif_t *hwif) |
| { |
| if (hwif->irq == 0) /* 0 is bogus but will do for now */ |
| hwif->irq = pci_get_legacy_ide_irq(hwif->pci_dev, hwif->channel); |
| |
| hwif->set_pio_mode = &amd_set_pio_mode; |
| hwif->set_dma_mode = &amd_set_drive; |
| |
| if (!hwif->dma_base) |
| return; |
| |
| hwif->ultra_mask = amd_config->udma_mask; |
| if (amd_config->flags & AMD_BAD_SWDMA) |
| hwif->swdma_mask = 0x00; |
| |
| if (hwif->cbl != ATA_CBL_PATA40_SHORT) { |
| if ((amd_80w >> hwif->channel) & 1) |
| hwif->cbl = ATA_CBL_PATA80; |
| else |
| hwif->cbl = ATA_CBL_PATA40; |
| } |
| } |
| |
| #define IDE_HFLAGS_AMD \ |
| (IDE_HFLAG_PIO_NO_BLACKLIST | \ |
| IDE_HFLAG_PIO_NO_DOWNGRADE | \ |
| IDE_HFLAG_ABUSE_SET_DMA_MODE | \ |
| IDE_HFLAG_POST_SET_MODE | \ |
| IDE_HFLAG_IO_32BIT | \ |
| IDE_HFLAG_UNMASK_IRQS | \ |
| IDE_HFLAG_BOOTABLE) |
| |
| #define DECLARE_AMD_DEV(name_str) \ |
| { \ |
| .name = name_str, \ |
| .init_chipset = init_chipset_amd74xx, \ |
| .init_hwif = init_hwif_amd74xx, \ |
| .enablebits = {{0x40,0x02,0x02}, {0x40,0x01,0x01}}, \ |
| .host_flags = IDE_HFLAGS_AMD, \ |
| .pio_mask = ATA_PIO5, \ |
| .swdma_mask = ATA_SWDMA2, \ |
| .mwdma_mask = ATA_MWDMA2, \ |
| } |
| |
| #define DECLARE_NV_DEV(name_str) \ |
| { \ |
| .name = name_str, \ |
| .init_chipset = init_chipset_amd74xx, \ |
| .init_hwif = init_hwif_amd74xx, \ |
| .enablebits = {{0x50,0x02,0x02}, {0x50,0x01,0x01}}, \ |
| .host_flags = IDE_HFLAGS_AMD, \ |
| .pio_mask = ATA_PIO5, \ |
| .swdma_mask = ATA_SWDMA2, \ |
| .mwdma_mask = ATA_MWDMA2, \ |
| } |
| |
| static const struct ide_port_info amd74xx_chipsets[] __devinitdata = { |
| /* 0 */ DECLARE_AMD_DEV("AMD7401"), |
| /* 1 */ DECLARE_AMD_DEV("AMD7409"), |
| /* 2 */ DECLARE_AMD_DEV("AMD7411"), |
| /* 3 */ DECLARE_AMD_DEV("AMD7441"), |
| /* 4 */ DECLARE_AMD_DEV("AMD8111"), |
| |
| /* 5 */ DECLARE_NV_DEV("NFORCE"), |
| /* 6 */ DECLARE_NV_DEV("NFORCE2"), |
| /* 7 */ DECLARE_NV_DEV("NFORCE2-U400R"), |
| /* 8 */ DECLARE_NV_DEV("NFORCE2-U400R-SATA"), |
| /* 9 */ DECLARE_NV_DEV("NFORCE3-150"), |
| /* 10 */ DECLARE_NV_DEV("NFORCE3-250"), |
| /* 11 */ DECLARE_NV_DEV("NFORCE3-250-SATA"), |
| /* 12 */ DECLARE_NV_DEV("NFORCE3-250-SATA2"), |
| /* 13 */ DECLARE_NV_DEV("NFORCE-CK804"), |
| /* 14 */ DECLARE_NV_DEV("NFORCE-MCP04"), |
| /* 15 */ DECLARE_NV_DEV("NFORCE-MCP51"), |
| /* 16 */ DECLARE_NV_DEV("NFORCE-MCP55"), |
| /* 17 */ DECLARE_NV_DEV("NFORCE-MCP61"), |
| /* 18 */ DECLARE_NV_DEV("NFORCE-MCP65"), |
| /* 19 */ DECLARE_NV_DEV("NFORCE-MCP67"), |
| /* 20 */ DECLARE_NV_DEV("NFORCE-MCP73"), |
| /* 21 */ DECLARE_NV_DEV("NFORCE-MCP77"), |
| /* 22 */ DECLARE_AMD_DEV("AMD5536"), |
| }; |
| |
| static int __devinit amd74xx_probe(struct pci_dev *dev, const struct pci_device_id *id) |
| { |
| amd_chipset = amd74xx_chipsets + id->driver_data; |
| amd_config = amd_ide_chips + id->driver_data; |
| if (dev->device != amd_config->id) { |
| printk(KERN_ERR "%s: assertion 0x%02x == 0x%02x failed !\n", |
| pci_name(dev), dev->device, amd_config->id); |
| return -ENODEV; |
| } |
| return ide_setup_pci_device(dev, amd_chipset); |
| } |
| |
| static const struct pci_device_id amd74xx_pci_tbl[] = { |
| { PCI_VDEVICE(AMD, PCI_DEVICE_ID_AMD_COBRA_7401), 0 }, |
| { PCI_VDEVICE(AMD, PCI_DEVICE_ID_AMD_VIPER_7409), 1 }, |
| { PCI_VDEVICE(AMD, PCI_DEVICE_ID_AMD_VIPER_7411), 2 }, |
| { PCI_VDEVICE(AMD, PCI_DEVICE_ID_AMD_OPUS_7441), 3 }, |
| { PCI_VDEVICE(AMD, PCI_DEVICE_ID_AMD_8111_IDE), 4 }, |
| { PCI_VDEVICE(NVIDIA, PCI_DEVICE_ID_NVIDIA_NFORCE_IDE), 5 }, |
| { PCI_VDEVICE(NVIDIA, PCI_DEVICE_ID_NVIDIA_NFORCE2_IDE), 6 }, |
| { PCI_VDEVICE(NVIDIA, PCI_DEVICE_ID_NVIDIA_NFORCE2S_IDE), 7 }, |
| #ifdef CONFIG_BLK_DEV_IDE_SATA |
| { PCI_VDEVICE(NVIDIA, PCI_DEVICE_ID_NVIDIA_NFORCE2S_SATA), 8 }, |
| #endif |
| { PCI_VDEVICE(NVIDIA, PCI_DEVICE_ID_NVIDIA_NFORCE3_IDE), 9 }, |
| { PCI_VDEVICE(NVIDIA, PCI_DEVICE_ID_NVIDIA_NFORCE3S_IDE), 10 }, |
| #ifdef CONFIG_BLK_DEV_IDE_SATA |
| { PCI_VDEVICE(NVIDIA, PCI_DEVICE_ID_NVIDIA_NFORCE3S_SATA), 11 }, |
| { PCI_VDEVICE(NVIDIA, PCI_DEVICE_ID_NVIDIA_NFORCE3S_SATA2), 12 }, |
| #endif |
| { PCI_VDEVICE(NVIDIA, PCI_DEVICE_ID_NVIDIA_NFORCE_CK804_IDE), 13 }, |
| { PCI_VDEVICE(NVIDIA, PCI_DEVICE_ID_NVIDIA_NFORCE_MCP04_IDE), 14 }, |
| { PCI_VDEVICE(NVIDIA, PCI_DEVICE_ID_NVIDIA_NFORCE_MCP51_IDE), 15 }, |
| { PCI_VDEVICE(NVIDIA, PCI_DEVICE_ID_NVIDIA_NFORCE_MCP55_IDE), 16 }, |
| { PCI_VDEVICE(NVIDIA, PCI_DEVICE_ID_NVIDIA_NFORCE_MCP61_IDE), 17 }, |
| { PCI_VDEVICE(NVIDIA, PCI_DEVICE_ID_NVIDIA_NFORCE_MCP65_IDE), 18 }, |
| { PCI_VDEVICE(NVIDIA, PCI_DEVICE_ID_NVIDIA_NFORCE_MCP67_IDE), 19 }, |
| { PCI_VDEVICE(NVIDIA, PCI_DEVICE_ID_NVIDIA_NFORCE_MCP73_IDE), 20 }, |
| { PCI_VDEVICE(NVIDIA, PCI_DEVICE_ID_NVIDIA_NFORCE_MCP77_IDE), 21 }, |
| { PCI_VDEVICE(AMD, PCI_DEVICE_ID_AMD_CS5536_IDE), 22 }, |
| { 0, }, |
| }; |
| MODULE_DEVICE_TABLE(pci, amd74xx_pci_tbl); |
| |
| static struct pci_driver driver = { |
| .name = "AMD_IDE", |
| .id_table = amd74xx_pci_tbl, |
| .probe = amd74xx_probe, |
| }; |
| |
| static int __init amd74xx_ide_init(void) |
| { |
| return ide_pci_register_driver(&driver); |
| } |
| |
| module_init(amd74xx_ide_init); |
| |
| MODULE_AUTHOR("Vojtech Pavlik"); |
| MODULE_DESCRIPTION("AMD PCI IDE driver"); |
| MODULE_LICENSE("GPL"); |