hwmon: (abituguru3) Use pr_fmt and pr_<level>
Added #define pr_fmt KBUILD_MODNAME ": " fmt
Converted printks to pr_<level>
Coalesced any long formats
Removed prefixes from formats
Added a few static strings to standardize logging messages.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
diff --git a/drivers/hwmon/abituguru3.c b/drivers/hwmon/abituguru3.c
index 3cf28af..48d21e2 100644
--- a/drivers/hwmon/abituguru3.c
+++ b/drivers/hwmon/abituguru3.c
@@ -23,6 +23,9 @@
chip found on newer Abit uGuru motherboards. Note: because of lack of specs
only reading the sensors and their settings is supported.
*/
+
+#define pr_fmt(fmt) KBUILD_MODNAME ": " fmt
+
#include <linux/module.h>
#include <linux/init.h>
#include <linux/slab.h>
@@ -608,6 +611,9 @@
module_param(verbose, bool, 0644);
MODULE_PARM_DESC(verbose, "Enable/disable verbose error reporting");
+static const char *never_happen = "This should never happen.";
+static const char *report_this =
+ "Please report this to the abituguru3 maintainer (see MAINTAINERS)";
/* wait while the uguru is busy (usually after a write) */
static int abituguru3_wait_while_busy(struct abituguru3_data *data)
@@ -940,15 +946,13 @@
if (abituguru3_motherboards[i].id == id)
break;
if (!abituguru3_motherboards[i].id) {
- printk(KERN_ERR ABIT_UGURU3_NAME ": error unknown motherboard "
- "ID: %04X. Please report this to the abituguru3 "
- "maintainer (see MAINTAINERS)\n", (unsigned int)id);
+ pr_err("error unknown motherboard ID: %04X. %s\n",
+ (unsigned int)id, report_this);
goto abituguru3_probe_error;
}
data->sensors = abituguru3_motherboards[i].sensors;
- printk(KERN_INFO ABIT_UGURU3_NAME ": found Abit uGuru3, motherboard "
- "ID: %04X\n", (unsigned int)id);
+ pr_info("found Abit uGuru3, motherboard ID: %04X\n", (unsigned int)id);
/* Fill the sysfs attr array */
sysfs_attr_i = 0;
@@ -957,11 +961,8 @@
for (i = 0; data->sensors[i].name; i++) {
/* Fail safe check, this should never happen! */
if (i >= ABIT_UGURU3_MAX_NO_SENSORS) {
- printk(KERN_ERR ABIT_UGURU3_NAME
- ": Fatal error motherboard has more sensors "
- "then ABIT_UGURU3_MAX_NO_SENSORS. This should "
- "never happen please report to the abituguru3 "
- "maintainer (see MAINTAINERS)\n");
+ pr_err("Fatal error motherboard has more sensors then ABIT_UGURU3_MAX_NO_SENSORS. %s %s\n",
+ never_happen, report_this);
res = -ENAMETOOLONG;
goto abituguru3_probe_error;
}
@@ -983,10 +984,8 @@
}
/* Fail safe check, this should never happen! */
if (sysfs_names_free < 0) {
- printk(KERN_ERR ABIT_UGURU3_NAME
- ": Fatal error ran out of space for sysfs attr names. "
- "This should never happen please report to the "
- "abituguru3 maintainer (see MAINTAINERS)\n");
+ pr_err("Fatal error ran out of space for sysfs attr names. %s %s\n",
+ never_happen, report_this);
res = -ENAMETOOLONG;
goto abituguru3_probe_error;
}
@@ -1189,8 +1188,7 @@
"0x%02X\n", (unsigned int)data_val, (unsigned int)cmd_val);
if (force) {
- printk(KERN_INFO ABIT_UGURU3_NAME ": Assuming Abit uGuru3 is "
- "present because of \"force\" parameter\n");
+ pr_info("Assuming Abit uGuru3 is present because of \"force\" parameter\n");
return 0;
}
@@ -1219,10 +1217,8 @@
return err;
#ifdef CONFIG_DMI
- printk(KERN_WARNING ABIT_UGURU3_NAME ": this motherboard was "
- "not detected using DMI. Please send the output of "
- "\"dmidecode\" to the abituguru3 maintainer "
- "(see MAINTAINERS)\n");
+ pr_warn("this motherboard was not detected using DMI. "
+ "Please send the output of \"dmidecode\" to the abituguru3 maintainer (see MAINTAINERS)\n");
#endif
}
@@ -1233,8 +1229,7 @@
abituguru3_pdev = platform_device_alloc(ABIT_UGURU3_NAME,
ABIT_UGURU3_BASE);
if (!abituguru3_pdev) {
- printk(KERN_ERR ABIT_UGURU3_NAME
- ": Device allocation failed\n");
+ pr_err("Device allocation failed\n");
err = -ENOMEM;
goto exit_driver_unregister;
}
@@ -1245,15 +1240,13 @@
err = platform_device_add_resources(abituguru3_pdev, &res, 1);
if (err) {
- printk(KERN_ERR ABIT_UGURU3_NAME
- ": Device resource addition failed (%d)\n", err);
+ pr_err("Device resource addition failed (%d)\n", err);
goto exit_device_put;
}
err = platform_device_add(abituguru3_pdev);
if (err) {
- printk(KERN_ERR ABIT_UGURU3_NAME
- ": Device addition failed (%d)\n", err);
+ pr_err("Device addition failed (%d)\n", err);
goto exit_device_put;
}