blob: 4fd25e737d9a60a3592af247ebb9213d7a96748d [file] [log] [blame]
Jeff Garzik669a5db2006-08-29 18:12:40 -04001/*
2 * pata_radisys.c - Intel PATA/SATA controllers
3 *
Alan Coxab771632008-10-27 15:09:10 +00004 * (C) 2006 Red Hat <alan@lxorguk.ukuu.org.uk>
Jeff Garzik669a5db2006-08-29 18:12:40 -04005 *
6 * Some parts based on ata_piix.c by Jeff Garzik and others.
7 *
8 * A PIIX relative, this device has a single ATA channel and no
9 * slave timings, SITRE or PPE. In that sense it is a close relative
10 * of the original PIIX. It does however support UDMA 33/66 per channel
11 * although no other modes/timings. Also lacking is 32bit I/O on the ATA
12 * port.
13 */
14
15#include <linux/kernel.h>
16#include <linux/module.h>
17#include <linux/pci.h>
18#include <linux/init.h>
19#include <linux/blkdev.h>
20#include <linux/delay.h>
21#include <linux/device.h>
22#include <scsi/scsi_host.h>
23#include <linux/libata.h>
24#include <linux/ata.h>
25
26#define DRV_NAME "pata_radisys"
Alan Coxd36a7642007-03-08 22:56:07 +000027#define DRV_VERSION "0.4.4"
Jeff Garzik669a5db2006-08-29 18:12:40 -040028
29/**
30 * radisys_set_piomode - Initialize host controller PATA PIO timings
Alan Coxd36a7642007-03-08 22:56:07 +000031 * @ap: ATA port
32 * @adev: Device whose timings we are configuring
Jeff Garzik669a5db2006-08-29 18:12:40 -040033 *
34 * Set PIO mode for device, in host controller PCI config space.
35 *
36 * LOCKING:
37 * None (inherited from caller).
38 */
39
40static void radisys_set_piomode (struct ata_port *ap, struct ata_device *adev)
41{
42 unsigned int pio = adev->pio_mode - XFER_PIO_0;
43 struct pci_dev *dev = to_pci_dev(ap->host->dev);
44 u16 idetm_data;
45 int control = 0;
46
47 /*
48 * See Intel Document 298600-004 for the timing programing rules
49 * for PIIX/ICH. Note that the early PIIX does not have the slave
50 * timing port at 0x44. The Radisys is a relative of the PIIX
51 * but not the same so be careful.
52 */
53
54 static const /* ISP RTC */
55 u8 timings[][2] = { { 0, 0 }, /* Check me */
56 { 0, 0 },
57 { 1, 1 },
58 { 2, 2 },
59 { 3, 3 }, };
60
61 if (pio > 0)
62 control |= 1; /* TIME1 enable */
63 if (ata_pio_need_iordy(adev))
64 control |= 2; /* IE IORDY */
65
66 pci_read_config_word(dev, 0x40, &idetm_data);
67
68 /* Enable IE and TIME as appropriate. Clear the other
69 drive timing bits */
70 idetm_data &= 0xCCCC;
71 idetm_data |= (control << (4 * adev->devno));
72 idetm_data |= (timings[pio][0] << 12) |
73 (timings[pio][1] << 8);
74 pci_write_config_word(dev, 0x40, idetm_data);
75
76 /* Track which port is configured */
77 ap->private_data = adev;
78}
79
80/**
81 * radisys_set_dmamode - Initialize host controller PATA DMA timings
82 * @ap: Port whose timings we are configuring
83 * @adev: Device to program
Jeff Garzik669a5db2006-08-29 18:12:40 -040084 *
85 * Set MWDMA mode for device, in host controller PCI config space.
86 *
87 * LOCKING:
88 * None (inherited from caller).
89 */
90
91static void radisys_set_dmamode (struct ata_port *ap, struct ata_device *adev)
92{
93 struct pci_dev *dev = to_pci_dev(ap->host->dev);
94 u16 idetm_data;
95 u8 udma_enable;
Jeff Garzik85cd7252006-08-31 00:03:49 -040096
Jeff Garzik669a5db2006-08-29 18:12:40 -040097 static const /* ISP RTC */
98 u8 timings[][2] = { { 0, 0 },
99 { 0, 0 },
100 { 1, 1 },
101 { 2, 2 },
102 { 3, 3 }, };
103
104 /*
105 * MWDMA is driven by the PIO timings. We must also enable
106 * IORDY unconditionally.
107 */
108
109 pci_read_config_word(dev, 0x40, &idetm_data);
110 pci_read_config_byte(dev, 0x48, &udma_enable);
111
112 if (adev->dma_mode < XFER_UDMA_0) {
113 unsigned int mwdma = adev->dma_mode - XFER_MW_DMA_0;
114 const unsigned int needed_pio[3] = {
115 XFER_PIO_0, XFER_PIO_3, XFER_PIO_4
116 };
117 int pio = needed_pio[mwdma] - XFER_PIO_0;
118 int control = 3; /* IORDY|TIME0 */
119
120 /* If the drive MWDMA is faster than it can do PIO then
121 we must force PIO0 for PIO cycles. */
122
123 if (adev->pio_mode < needed_pio[mwdma])
124 control = 1;
125
126 /* Mask out the relevant control and timing bits we will load. Also
127 clear the other drive TIME register as a precaution */
Jeff Garzik85cd7252006-08-31 00:03:49 -0400128
Jeff Garzik669a5db2006-08-29 18:12:40 -0400129 idetm_data &= 0xCCCC;
130 idetm_data |= control << (4 * adev->devno);
131 idetm_data |= (timings[pio][0] << 12) | (timings[pio][1] << 8);
132
133 udma_enable &= ~(1 << adev->devno);
134 } else {
135 u8 udma_mode;
Jeff Garzik85cd7252006-08-31 00:03:49 -0400136
Jeff Garzik669a5db2006-08-29 18:12:40 -0400137 /* UDMA66 on: UDMA 33 and 66 are switchable via register 0x4A */
Jeff Garzik85cd7252006-08-31 00:03:49 -0400138
Jeff Garzik669a5db2006-08-29 18:12:40 -0400139 pci_read_config_byte(dev, 0x4A, &udma_mode);
Jeff Garzik85cd7252006-08-31 00:03:49 -0400140
Jeff Garzik669a5db2006-08-29 18:12:40 -0400141 if (adev->xfer_mode == XFER_UDMA_2)
Bartlomiej Zolnierkiewiczdd4a43c2009-12-03 20:32:13 +0100142 udma_mode &= ~(2 << (adev->devno * 4));
Jeff Garzik669a5db2006-08-29 18:12:40 -0400143 else /* UDMA 4 */
Bartlomiej Zolnierkiewiczdd4a43c2009-12-03 20:32:13 +0100144 udma_mode |= (2 << (adev->devno * 4));
Jeff Garzik85cd7252006-08-31 00:03:49 -0400145
Jeff Garzik669a5db2006-08-29 18:12:40 -0400146 pci_write_config_byte(dev, 0x4A, udma_mode);
Jeff Garzik85cd7252006-08-31 00:03:49 -0400147
Jeff Garzik669a5db2006-08-29 18:12:40 -0400148 udma_enable |= (1 << adev->devno);
149 }
150 pci_write_config_word(dev, 0x40, idetm_data);
151 pci_write_config_byte(dev, 0x48, udma_enable);
152
153 /* Track which port is configured */
154 ap->private_data = adev;
155}
156
157/**
Tejun Heo9363c382008-04-07 22:47:16 +0900158 * radisys_qc_issue - command issue
Jeff Garzik669a5db2006-08-29 18:12:40 -0400159 * @qc: command pending
160 *
161 * Called when the libata layer is about to issue a command. We wrap
162 * this interface so that we can load the correct ATA timings if
Robert P. J. Day3a4fa0a2007-10-19 23:10:43 +0200163 * necessary. Our logic also clears TIME0/TIME1 for the other device so
Jeff Garzik669a5db2006-08-29 18:12:40 -0400164 * that, even if we get this wrong, cycles to the other device will
165 * be made PIO0.
166 */
167
Tejun Heo9363c382008-04-07 22:47:16 +0900168static unsigned int radisys_qc_issue(struct ata_queued_cmd *qc)
Jeff Garzik669a5db2006-08-29 18:12:40 -0400169{
170 struct ata_port *ap = qc->ap;
171 struct ata_device *adev = qc->dev;
172
173 if (adev != ap->private_data) {
174 /* UDMA timing is not shared */
175 if (adev->dma_mode < XFER_UDMA_0) {
176 if (adev->dma_mode)
177 radisys_set_dmamode(ap, adev);
178 else if (adev->pio_mode)
179 radisys_set_piomode(ap, adev);
180 }
181 }
Tejun Heo9363c382008-04-07 22:47:16 +0900182 return ata_sff_qc_issue(qc);
Jeff Garzik669a5db2006-08-29 18:12:40 -0400183}
184
185
186static struct scsi_host_template radisys_sht = {
Tejun Heo68d1d072008-03-25 12:22:49 +0900187 ATA_BMDMA_SHT(DRV_NAME),
Jeff Garzik669a5db2006-08-29 18:12:40 -0400188};
189
Tejun Heo029cfd62008-03-25 12:22:49 +0900190static struct ata_port_operations radisys_pata_ops = {
191 .inherits = &ata_bmdma_port_ops,
Tejun Heo9363c382008-04-07 22:47:16 +0900192 .qc_issue = radisys_qc_issue,
Tejun Heo029cfd62008-03-25 12:22:49 +0900193 .cable_detect = ata_cable_unknown,
Jeff Garzik669a5db2006-08-29 18:12:40 -0400194 .set_piomode = radisys_set_piomode,
195 .set_dmamode = radisys_set_dmamode,
Jeff Garzik669a5db2006-08-29 18:12:40 -0400196};
197
198
199/**
200 * radisys_init_one - Register PIIX ATA PCI device with kernel services
201 * @pdev: PCI device to register
202 * @ent: Entry in radisys_pci_tbl matching with @pdev
203 *
204 * Called from kernel PCI layer. We probe for combined mode (sigh),
205 * and then hand over control to libata, for it to do the rest.
206 *
207 * LOCKING:
208 * Inherited from PCI layer (may sleep).
209 *
210 * RETURNS:
211 * Zero on success, or -ERRNO value.
212 */
213
214static int radisys_init_one (struct pci_dev *pdev, const struct pci_device_id *ent)
215{
216 static int printed_version;
Tejun Heo1626aeb2007-05-04 12:43:58 +0200217 static const struct ata_port_info info = {
Jeff Garzik1d2808f2007-05-28 06:59:48 -0400218 .flags = ATA_FLAG_SLAVE_POSS,
Erik Inge Bolsø14bdef92009-03-14 21:38:24 +0100219 .pio_mask = ATA_PIO4,
Erik Inge Bolsøaef37d82009-03-14 23:07:33 +0100220 .mwdma_mask = ATA_MWDMA12_ONLY,
Erik Inge Bolsø14bdef92009-03-14 21:38:24 +0100221 .udma_mask = ATA_UDMA24_ONLY,
Jeff Garzik669a5db2006-08-29 18:12:40 -0400222 .port_ops = &radisys_pata_ops,
223 };
Tejun Heo1626aeb2007-05-04 12:43:58 +0200224 const struct ata_port_info *ppi[] = { &info, NULL };
Jeff Garzik669a5db2006-08-29 18:12:40 -0400225
226 if (!printed_version++)
227 dev_printk(KERN_DEBUG, &pdev->dev,
228 "version " DRV_VERSION "\n");
229
Tejun Heo9363c382008-04-07 22:47:16 +0900230 return ata_pci_sff_init_one(pdev, ppi, &radisys_sht, NULL);
Jeff Garzik669a5db2006-08-29 18:12:40 -0400231}
232
233static const struct pci_device_id radisys_pci_tbl[] = {
Jeff Garzik2d2744f2006-09-28 20:21:59 -0400234 { PCI_VDEVICE(RADISYS, 0x8201), },
235
Jeff Garzik669a5db2006-08-29 18:12:40 -0400236 { } /* terminate list */
237};
238
239static struct pci_driver radisys_pci_driver = {
240 .name = DRV_NAME,
241 .id_table = radisys_pci_tbl,
242 .probe = radisys_init_one,
243 .remove = ata_pci_remove_one,
Tejun Heo438ac6d2007-03-02 17:31:26 +0900244#ifdef CONFIG_PM
Alan30ced0f2006-11-22 16:57:36 +0000245 .suspend = ata_pci_device_suspend,
246 .resume = ata_pci_device_resume,
Tejun Heo438ac6d2007-03-02 17:31:26 +0900247#endif
Jeff Garzik669a5db2006-08-29 18:12:40 -0400248};
249
250static int __init radisys_init(void)
251{
252 return pci_register_driver(&radisys_pci_driver);
253}
254
255static void __exit radisys_exit(void)
256{
257 pci_unregister_driver(&radisys_pci_driver);
258}
259
Jeff Garzik669a5db2006-08-29 18:12:40 -0400260module_init(radisys_init);
261module_exit(radisys_exit);
262
263MODULE_AUTHOR("Alan Cox");
264MODULE_DESCRIPTION("SCSI low-level driver for Radisys R82600 controllers");
265MODULE_LICENSE("GPL");
266MODULE_DEVICE_TABLE(pci, radisys_pci_tbl);
267MODULE_VERSION(DRV_VERSION);
268