Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 1 | /* atp.c: Attached (pocket) ethernet adapter driver for linux. */ |
| 2 | /* |
| 3 | This is a driver for commonly OEM pocket (parallel port) |
| 4 | ethernet adapters based on the Realtek RTL8002 and RTL8012 chips. |
| 5 | |
| 6 | Written 1993-2000 by Donald Becker. |
| 7 | |
| 8 | This software may be used and distributed according to the terms of |
| 9 | the GNU General Public License (GPL), incorporated herein by reference. |
| 10 | Drivers based on or derived from this code fall under the GPL and must |
| 11 | retain the authorship, copyright and license notice. This file is not |
| 12 | a complete program and may only be used when the entire operating |
| 13 | system is licensed under the GPL. |
| 14 | |
| 15 | Copyright 1993 United States Government as represented by the Director, |
| 16 | National Security Agency. Copyright 1994-2000 retained by the original |
| 17 | author, Donald Becker. The timer-based reset code was supplied in 1995 |
| 18 | by Bill Carlson, wwc@super.org. |
| 19 | |
| 20 | The author may be reached as becker@scyld.com, or C/O |
| 21 | Scyld Computing Corporation |
| 22 | 410 Severn Ave., Suite 210 |
| 23 | Annapolis MD 21403 |
| 24 | |
| 25 | Support information and updates available at |
| 26 | http://www.scyld.com/network/atp.html |
| 27 | |
| 28 | |
| 29 | Modular support/softnet added by Alan Cox. |
| 30 | _bit abuse fixed up by Alan Cox |
| 31 | |
| 32 | */ |
| 33 | |
Markus Dahms | 2c2a8c5 | 2007-05-09 07:58:10 +0200 | [diff] [blame] | 34 | static const char version[] = |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 35 | "atp.c:v1.09=ac 2002/10/01 Donald Becker <becker@scyld.com>\n"; |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 36 | |
| 37 | /* The user-configurable values. |
| 38 | These may be modified when a driver module is loaded.*/ |
| 39 | |
| 40 | static int debug = 1; /* 1 normal messages, 0 quiet .. 7 verbose. */ |
| 41 | #define net_debug debug |
| 42 | |
| 43 | /* Maximum events (Rx packets, etc.) to handle at each interrupt. */ |
| 44 | static int max_interrupt_work = 15; |
| 45 | |
| 46 | #define NUM_UNITS 2 |
| 47 | /* The standard set of ISA module parameters. */ |
| 48 | static int io[NUM_UNITS]; |
| 49 | static int irq[NUM_UNITS]; |
| 50 | static int xcvr[NUM_UNITS]; /* The data transfer mode. */ |
| 51 | |
| 52 | /* Operational parameters that are set at compile time. */ |
| 53 | |
| 54 | /* Time in jiffies before concluding the transmitter is hung. */ |
| 55 | #define TX_TIMEOUT (400*HZ/1000) |
| 56 | |
| 57 | /* |
| 58 | This file is a device driver for the RealTek (aka AT-Lan-Tec) pocket |
| 59 | ethernet adapter. This is a common low-cost OEM pocket ethernet |
| 60 | adapter, sold under many names. |
| 61 | |
| 62 | Sources: |
| 63 | This driver was written from the packet driver assembly code provided by |
| 64 | Vincent Bono of AT-Lan-Tec. Ever try to figure out how a complicated |
| 65 | device works just from the assembly code? It ain't pretty. The following |
| 66 | description is written based on guesses and writing lots of special-purpose |
| 67 | code to test my theorized operation. |
| 68 | |
| 69 | In 1997 Realtek made available the documentation for the second generation |
| 70 | RTL8012 chip, which has lead to several driver improvements. |
| 71 | http://www.realtek.com.tw/cn/cn.html |
| 72 | |
| 73 | Theory of Operation |
| 74 | |
| 75 | The RTL8002 adapter seems to be built around a custom spin of the SEEQ |
| 76 | controller core. It probably has a 16K or 64K internal packet buffer, of |
| 77 | which the first 4K is devoted to transmit and the rest to receive. |
| 78 | The controller maintains the queue of received packet and the packet buffer |
| 79 | access pointer internally, with only 'reset to beginning' and 'skip to next |
| 80 | packet' commands visible. The transmit packet queue holds two (or more?) |
| 81 | packets: both 'retransmit this packet' (due to collision) and 'transmit next |
| 82 | packet' commands must be started by hand. |
| 83 | |
| 84 | The station address is stored in a standard bit-serial EEPROM which must be |
| 85 | read (ughh) by the device driver. (Provisions have been made for |
| 86 | substituting a 74S288 PROM, but I haven't gotten reports of any models |
| 87 | using it.) Unlike built-in devices, a pocket adapter can temporarily lose |
| 88 | power without indication to the device driver. The major effect is that |
| 89 | the station address, receive filter (promiscuous, etc.) and transceiver |
| 90 | must be reset. |
| 91 | |
| 92 | The controller itself has 16 registers, some of which use only the lower |
| 93 | bits. The registers are read and written 4 bits at a time. The four bit |
| 94 | register address is presented on the data lines along with a few additional |
| 95 | timing and control bits. The data is then read from status port or written |
| 96 | to the data port. |
| 97 | |
| 98 | Correction: the controller has two banks of 16 registers. The second |
| 99 | bank contains only the multicast filter table (now used) and the EEPROM |
| 100 | access registers. |
| 101 | |
| 102 | Since the bulk data transfer of the actual packets through the slow |
| 103 | parallel port dominates the driver's running time, four distinct data |
| 104 | (non-register) transfer modes are provided by the adapter, two in each |
| 105 | direction. In the first mode timing for the nibble transfers is |
| 106 | provided through the data port. In the second mode the same timing is |
| 107 | provided through the control port. In either case the data is read from |
| 108 | the status port and written to the data port, just as it is accessing |
| 109 | registers. |
| 110 | |
| 111 | In addition to the basic data transfer methods, several more are modes are |
| 112 | created by adding some delay by doing multiple reads of the data to allow |
| 113 | it to stabilize. This delay seems to be needed on most machines. |
| 114 | |
| 115 | The data transfer mode is stored in the 'dev->if_port' field. Its default |
| 116 | value is '4'. It may be overridden at boot-time using the third parameter |
| 117 | to the "ether=..." initialization. |
| 118 | |
| 119 | The header file <atp.h> provides inline functions that encapsulate the |
| 120 | register and data access methods. These functions are hand-tuned to |
| 121 | generate reasonable object code. This header file also documents my |
| 122 | interpretations of the device registers. |
| 123 | */ |
| 124 | |
| 125 | #include <linux/kernel.h> |
| 126 | #include <linux/module.h> |
| 127 | #include <linux/types.h> |
| 128 | #include <linux/fcntl.h> |
| 129 | #include <linux/interrupt.h> |
| 130 | #include <linux/ioport.h> |
| 131 | #include <linux/in.h> |
| 132 | #include <linux/slab.h> |
| 133 | #include <linux/string.h> |
| 134 | #include <linux/errno.h> |
| 135 | #include <linux/init.h> |
| 136 | #include <linux/crc32.h> |
| 137 | #include <linux/netdevice.h> |
| 138 | #include <linux/etherdevice.h> |
| 139 | #include <linux/skbuff.h> |
| 140 | #include <linux/spinlock.h> |
| 141 | #include <linux/delay.h> |
| 142 | #include <linux/bitops.h> |
| 143 | |
| 144 | #include <asm/system.h> |
| 145 | #include <asm/io.h> |
| 146 | #include <asm/dma.h> |
| 147 | |
| 148 | #include "atp.h" |
| 149 | |
| 150 | MODULE_AUTHOR("Donald Becker <becker@scyld.com>"); |
| 151 | MODULE_DESCRIPTION("RealTek RTL8002/8012 parallel port Ethernet driver"); |
| 152 | MODULE_LICENSE("GPL"); |
| 153 | |
| 154 | module_param(max_interrupt_work, int, 0); |
| 155 | module_param(debug, int, 0); |
| 156 | module_param_array(io, int, NULL, 0); |
| 157 | module_param_array(irq, int, NULL, 0); |
| 158 | module_param_array(xcvr, int, NULL, 0); |
| 159 | MODULE_PARM_DESC(max_interrupt_work, "ATP maximum events handled per interrupt"); |
| 160 | MODULE_PARM_DESC(debug, "ATP debug level (0-7)"); |
| 161 | MODULE_PARM_DESC(io, "ATP I/O base address(es)"); |
| 162 | MODULE_PARM_DESC(irq, "ATP IRQ number(s)"); |
| 163 | MODULE_PARM_DESC(xcvr, "ATP transceiver(s) (0=internal, 1=external)"); |
| 164 | |
| 165 | /* The number of low I/O ports used by the ethercard. */ |
| 166 | #define ETHERCARD_TOTAL_SIZE 3 |
| 167 | |
| 168 | /* Sequence to switch an 8012 from printer mux to ethernet mode. */ |
| 169 | static char mux_8012[] = { 0xff, 0xf7, 0xff, 0xfb, 0xf3, 0xfb, 0xff, 0xf7,}; |
| 170 | |
| 171 | struct net_local { |
| 172 | spinlock_t lock; |
| 173 | struct net_device *next_module; |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 174 | struct timer_list timer; /* Media selection timer. */ |
| 175 | long last_rx_time; /* Last Rx, in jiffies, to handle Rx hang. */ |
| 176 | int saved_tx_size; |
| 177 | unsigned int tx_unit_busy:1; |
| 178 | unsigned char re_tx, /* Number of packet retransmissions. */ |
| 179 | addr_mode, /* Current Rx filter e.g. promiscuous, etc. */ |
| 180 | pac_cnt_in_tx_buf, |
| 181 | chip_type; |
| 182 | }; |
| 183 | |
| 184 | /* This code, written by wwc@super.org, resets the adapter every |
| 185 | TIMED_CHECKER ticks. This recovers from an unknown error which |
| 186 | hangs the device. */ |
| 187 | #define TIMED_CHECKER (HZ/4) |
| 188 | #ifdef TIMED_CHECKER |
| 189 | #include <linux/timer.h> |
| 190 | static void atp_timed_checker(unsigned long ignored); |
| 191 | #endif |
| 192 | |
| 193 | /* Index to functions, as function prototypes. */ |
| 194 | |
| 195 | static int atp_probe1(long ioaddr); |
| 196 | static void get_node_ID(struct net_device *dev); |
| 197 | static unsigned short eeprom_op(long ioaddr, unsigned int cmd); |
| 198 | static int net_open(struct net_device *dev); |
| 199 | static void hardware_init(struct net_device *dev); |
| 200 | static void write_packet(long ioaddr, int length, unsigned char *packet, int pad, int mode); |
| 201 | static void trigger_send(long ioaddr, int length); |
Stephen Hemminger | 61357325 | 2009-08-31 19:50:58 +0000 | [diff] [blame] | 202 | static netdev_tx_t atp_send_packet(struct sk_buff *skb, |
| 203 | struct net_device *dev); |
David Howells | 7d12e78 | 2006-10-05 14:55:46 +0100 | [diff] [blame] | 204 | static irqreturn_t atp_interrupt(int irq, void *dev_id); |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 205 | static void net_rx(struct net_device *dev); |
| 206 | static void read_block(long ioaddr, int length, unsigned char *buffer, int data_mode); |
| 207 | static int net_close(struct net_device *dev); |
Stephen Hemminger | 3a1a27f | 2009-01-07 18:10:24 -0800 | [diff] [blame] | 208 | static void set_rx_mode(struct net_device *dev); |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 209 | static void tx_timeout(struct net_device *dev); |
| 210 | |
| 211 | |
| 212 | /* A list of all installed ATP devices, for removing the driver module. */ |
| 213 | static struct net_device *root_atp_dev; |
| 214 | |
| 215 | /* Check for a network adapter of this type, and return '0' iff one exists. |
| 216 | If dev->base_addr == 0, probe all likely locations. |
| 217 | If dev->base_addr == 1, always return failure. |
| 218 | If dev->base_addr == 2, allocate space for the device and return success |
| 219 | (detachable devices only). |
Jeff Garzik | 6aa20a2 | 2006-09-13 13:24:59 -0400 | [diff] [blame] | 220 | |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 221 | FIXME: we should use the parport layer for this |
| 222 | */ |
| 223 | static int __init atp_init(void) |
| 224 | { |
| 225 | int *port, ports[] = {0x378, 0x278, 0x3bc, 0}; |
| 226 | int base_addr = io[0]; |
| 227 | |
| 228 | if (base_addr > 0x1ff) /* Check a single specified location. */ |
| 229 | return atp_probe1(base_addr); |
| 230 | else if (base_addr == 1) /* Don't probe at all. */ |
| 231 | return -ENXIO; |
| 232 | |
| 233 | for (port = ports; *port; port++) { |
| 234 | long ioaddr = *port; |
| 235 | outb(0x57, ioaddr + PAR_DATA); |
| 236 | if (inb(ioaddr + PAR_DATA) != 0x57) |
| 237 | continue; |
| 238 | if (atp_probe1(ioaddr) == 0) |
| 239 | return 0; |
| 240 | } |
| 241 | |
| 242 | return -ENODEV; |
| 243 | } |
| 244 | |
Stephen Hemminger | 3a1a27f | 2009-01-07 18:10:24 -0800 | [diff] [blame] | 245 | static const struct net_device_ops atp_netdev_ops = { |
| 246 | .ndo_open = net_open, |
| 247 | .ndo_stop = net_close, |
| 248 | .ndo_start_xmit = atp_send_packet, |
| 249 | .ndo_set_multicast_list = set_rx_mode, |
| 250 | .ndo_tx_timeout = tx_timeout, |
| 251 | .ndo_change_mtu = eth_change_mtu, |
| 252 | .ndo_set_mac_address = eth_mac_addr, |
| 253 | .ndo_validate_addr = eth_validate_addr, |
| 254 | }; |
| 255 | |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 256 | static int __init atp_probe1(long ioaddr) |
| 257 | { |
| 258 | struct net_device *dev = NULL; |
| 259 | struct net_local *lp; |
| 260 | int saved_ctrl_reg, status, i; |
| 261 | int res; |
| 262 | |
| 263 | outb(0xff, ioaddr + PAR_DATA); |
| 264 | /* Save the original value of the Control register, in case we guessed |
| 265 | wrong. */ |
| 266 | saved_ctrl_reg = inb(ioaddr + PAR_CONTROL); |
| 267 | if (net_debug > 3) |
| 268 | printk("atp: Control register was %#2.2x.\n", saved_ctrl_reg); |
| 269 | /* IRQEN=0, SLCTB=high INITB=high, AUTOFDB=high, STBB=high. */ |
| 270 | outb(0x04, ioaddr + PAR_CONTROL); |
| 271 | #ifndef final_version |
| 272 | if (net_debug > 3) { |
| 273 | /* Turn off the printer multiplexer on the 8012. */ |
| 274 | for (i = 0; i < 8; i++) |
| 275 | outb(mux_8012[i], ioaddr + PAR_DATA); |
| 276 | write_reg(ioaddr, MODSEL, 0x00); |
| 277 | printk("atp: Registers are "); |
| 278 | for (i = 0; i < 32; i++) |
| 279 | printk(" %2.2x", read_nibble(ioaddr, i)); |
| 280 | printk(".\n"); |
| 281 | } |
| 282 | #endif |
| 283 | /* Turn off the printer multiplexer on the 8012. */ |
| 284 | for (i = 0; i < 8; i++) |
| 285 | outb(mux_8012[i], ioaddr + PAR_DATA); |
| 286 | write_reg_high(ioaddr, CMR1, CMR1h_RESET); |
| 287 | /* udelay() here? */ |
| 288 | status = read_nibble(ioaddr, CMR1); |
| 289 | |
| 290 | if (net_debug > 3) { |
| 291 | printk(KERN_DEBUG "atp: Status nibble was %#2.2x..", status); |
| 292 | for (i = 0; i < 32; i++) |
| 293 | printk(" %2.2x", read_nibble(ioaddr, i)); |
| 294 | printk("\n"); |
| 295 | } |
| 296 | |
| 297 | if ((status & 0x78) != 0x08) { |
| 298 | /* The pocket adapter probe failed, restore the control register. */ |
| 299 | outb(saved_ctrl_reg, ioaddr + PAR_CONTROL); |
| 300 | return -ENODEV; |
| 301 | } |
| 302 | status = read_nibble(ioaddr, CMR2_h); |
| 303 | if ((status & 0x78) != 0x10) { |
| 304 | outb(saved_ctrl_reg, ioaddr + PAR_CONTROL); |
| 305 | return -ENODEV; |
| 306 | } |
| 307 | |
| 308 | dev = alloc_etherdev(sizeof(struct net_local)); |
| 309 | if (!dev) |
| 310 | return -ENOMEM; |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 311 | |
| 312 | /* Find the IRQ used by triggering an interrupt. */ |
| 313 | write_reg_byte(ioaddr, CMR2, 0x01); /* No accept mode, IRQ out. */ |
| 314 | write_reg_high(ioaddr, CMR1, CMR1h_RxENABLE | CMR1h_TxENABLE); /* Enable Tx and Rx. */ |
| 315 | |
| 316 | /* Omit autoIRQ routine for now. Use "table lookup" instead. Uhgggh. */ |
| 317 | if (irq[0]) |
| 318 | dev->irq = irq[0]; |
| 319 | else if (ioaddr == 0x378) |
| 320 | dev->irq = 7; |
| 321 | else |
| 322 | dev->irq = 5; |
| 323 | write_reg_high(ioaddr, CMR1, CMR1h_TxRxOFF); /* Disable Tx and Rx units. */ |
| 324 | write_reg(ioaddr, CMR2, CMR2_NULL); |
| 325 | |
| 326 | dev->base_addr = ioaddr; |
| 327 | |
| 328 | /* Read the station address PROM. */ |
| 329 | get_node_ID(dev); |
| 330 | |
| 331 | #ifndef MODULE |
| 332 | if (net_debug) |
Markus Dahms | 2c2a8c5 | 2007-05-09 07:58:10 +0200 | [diff] [blame] | 333 | printk(KERN_INFO "%s", version); |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 334 | #endif |
| 335 | |
Joe Perches | 0795af5 | 2007-10-03 17:59:30 -0700 | [diff] [blame] | 336 | printk(KERN_NOTICE "%s: Pocket adapter found at %#3lx, IRQ %d, " |
Johannes Berg | e174961 | 2008-10-27 15:59:26 -0700 | [diff] [blame] | 337 | "SAPROM %pM.\n", |
| 338 | dev->name, dev->base_addr, dev->irq, dev->dev_addr); |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 339 | |
| 340 | /* Reset the ethernet hardware and activate the printer pass-through. */ |
| 341 | write_reg_high(ioaddr, CMR1, CMR1h_RESET | CMR1h_MUX); |
| 342 | |
| 343 | lp = netdev_priv(dev); |
| 344 | lp->chip_type = RTL8002; |
| 345 | lp->addr_mode = CMR2h_Normal; |
| 346 | spin_lock_init(&lp->lock); |
| 347 | |
| 348 | /* For the ATP adapter the "if_port" is really the data transfer mode. */ |
| 349 | if (xcvr[0]) |
| 350 | dev->if_port = xcvr[0]; |
| 351 | else |
| 352 | dev->if_port = (dev->mem_start & 0xf) ? (dev->mem_start & 0x7) : 4; |
| 353 | if (dev->mem_end & 0xf) |
| 354 | net_debug = dev->mem_end & 7; |
| 355 | |
Stephen Hemminger | 3a1a27f | 2009-01-07 18:10:24 -0800 | [diff] [blame] | 356 | dev->netdev_ops = &atp_netdev_ops; |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 357 | dev->watchdog_timeo = TX_TIMEOUT; |
| 358 | |
| 359 | res = register_netdev(dev); |
| 360 | if (res) { |
| 361 | free_netdev(dev); |
| 362 | return res; |
| 363 | } |
| 364 | |
| 365 | lp->next_module = root_atp_dev; |
| 366 | root_atp_dev = dev; |
| 367 | |
| 368 | return 0; |
| 369 | } |
| 370 | |
| 371 | /* Read the station address PROM, usually a word-wide EEPROM. */ |
| 372 | static void __init get_node_ID(struct net_device *dev) |
| 373 | { |
| 374 | long ioaddr = dev->base_addr; |
| 375 | int sa_offset = 0; |
| 376 | int i; |
| 377 | |
| 378 | write_reg(ioaddr, CMR2, CMR2_EEPROM); /* Point to the EEPROM control registers. */ |
| 379 | |
| 380 | /* Some adapters have the station address at offset 15 instead of offset |
| 381 | zero. Check for it, and fix it if needed. */ |
| 382 | if (eeprom_op(ioaddr, EE_READ(0)) == 0xffff) |
| 383 | sa_offset = 15; |
| 384 | |
| 385 | for (i = 0; i < 3; i++) |
Al Viro | eca1ad8 | 2008-03-16 22:21:54 +0000 | [diff] [blame] | 386 | ((__be16 *)dev->dev_addr)[i] = |
| 387 | cpu_to_be16(eeprom_op(ioaddr, EE_READ(sa_offset + i))); |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 388 | |
| 389 | write_reg(ioaddr, CMR2, CMR2_NULL); |
| 390 | } |
| 391 | |
| 392 | /* |
| 393 | An EEPROM read command starts by shifting out 0x60+address, and then |
| 394 | shifting in the serial data. See the NatSemi databook for details. |
| 395 | * ________________ |
| 396 | * CS : __| |
| 397 | * ___ ___ |
| 398 | * CLK: ______| |___| | |
| 399 | * __ _______ _______ |
| 400 | * DI : __X_______X_______X |
| 401 | * DO : _________X_______X |
| 402 | */ |
| 403 | |
| 404 | static unsigned short __init eeprom_op(long ioaddr, u32 cmd) |
| 405 | { |
| 406 | unsigned eedata_out = 0; |
| 407 | int num_bits = EE_CMD_SIZE; |
| 408 | |
| 409 | while (--num_bits >= 0) { |
| 410 | char outval = (cmd & (1<<num_bits)) ? EE_DATA_WRITE : 0; |
| 411 | write_reg_high(ioaddr, PROM_CMD, outval | EE_CLK_LOW); |
| 412 | write_reg_high(ioaddr, PROM_CMD, outval | EE_CLK_HIGH); |
| 413 | eedata_out <<= 1; |
| 414 | if (read_nibble(ioaddr, PROM_DATA) & EE_DATA_READ) |
| 415 | eedata_out++; |
| 416 | } |
| 417 | write_reg_high(ioaddr, PROM_CMD, EE_CLK_LOW & ~EE_CS); |
| 418 | return eedata_out; |
| 419 | } |
| 420 | |
| 421 | |
| 422 | /* Open/initialize the board. This is called (in the current kernel) |
| 423 | sometime after booting when the 'ifconfig' program is run. |
| 424 | |
| 425 | This routine sets everything up anew at each open, even |
| 426 | registers that "should" only need to be set once at boot, so that |
| 427 | there is non-reboot way to recover if something goes wrong. |
| 428 | |
Wang Chen | b74ca3a | 2008-12-08 01:14:16 -0800 | [diff] [blame] | 429 | This is an attachable device: if there is no private entry then it wasn't |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 430 | probed for at boot-time, and we need to probe for it again. |
| 431 | */ |
| 432 | static int net_open(struct net_device *dev) |
| 433 | { |
| 434 | struct net_local *lp = netdev_priv(dev); |
| 435 | int ret; |
| 436 | |
| 437 | /* The interrupt line is turned off (tri-stated) when the device isn't in |
| 438 | use. That's especially important for "attached" interfaces where the |
| 439 | port or interrupt may be shared. */ |
Joe Perches | a0607fd | 2009-11-18 23:29:17 -0800 | [diff] [blame] | 440 | ret = request_irq(dev->irq, atp_interrupt, 0, dev->name, dev); |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 441 | if (ret) |
| 442 | return ret; |
| 443 | |
| 444 | hardware_init(dev); |
| 445 | |
| 446 | init_timer(&lp->timer); |
| 447 | lp->timer.expires = jiffies + TIMED_CHECKER; |
| 448 | lp->timer.data = (unsigned long)dev; |
| 449 | lp->timer.function = &atp_timed_checker; /* timer handler */ |
| 450 | add_timer(&lp->timer); |
| 451 | |
| 452 | netif_start_queue(dev); |
| 453 | return 0; |
| 454 | } |
| 455 | |
| 456 | /* This routine resets the hardware. We initialize everything, assuming that |
| 457 | the hardware may have been temporarily detached. */ |
| 458 | static void hardware_init(struct net_device *dev) |
| 459 | { |
| 460 | struct net_local *lp = netdev_priv(dev); |
| 461 | long ioaddr = dev->base_addr; |
| 462 | int i; |
| 463 | |
| 464 | /* Turn off the printer multiplexer on the 8012. */ |
| 465 | for (i = 0; i < 8; i++) |
| 466 | outb(mux_8012[i], ioaddr + PAR_DATA); |
| 467 | write_reg_high(ioaddr, CMR1, CMR1h_RESET); |
| 468 | |
| 469 | for (i = 0; i < 6; i++) |
| 470 | write_reg_byte(ioaddr, PAR0 + i, dev->dev_addr[i]); |
| 471 | |
| 472 | write_reg_high(ioaddr, CMR2, lp->addr_mode); |
| 473 | |
| 474 | if (net_debug > 2) { |
| 475 | printk(KERN_DEBUG "%s: Reset: current Rx mode %d.\n", dev->name, |
| 476 | (read_nibble(ioaddr, CMR2_h) >> 3) & 0x0f); |
| 477 | } |
| 478 | |
| 479 | write_reg(ioaddr, CMR2, CMR2_IRQOUT); |
| 480 | write_reg_high(ioaddr, CMR1, CMR1h_RxENABLE | CMR1h_TxENABLE); |
| 481 | |
| 482 | /* Enable the interrupt line from the serial port. */ |
| 483 | outb(Ctrl_SelData + Ctrl_IRQEN, ioaddr + PAR_CONTROL); |
| 484 | |
| 485 | /* Unmask the interesting interrupts. */ |
| 486 | write_reg(ioaddr, IMR, ISR_RxOK | ISR_TxErr | ISR_TxOK); |
| 487 | write_reg_high(ioaddr, IMR, ISRh_RxErr); |
| 488 | |
| 489 | lp->tx_unit_busy = 0; |
| 490 | lp->pac_cnt_in_tx_buf = 0; |
| 491 | lp->saved_tx_size = 0; |
| 492 | } |
| 493 | |
| 494 | static void trigger_send(long ioaddr, int length) |
| 495 | { |
| 496 | write_reg_byte(ioaddr, TxCNT0, length & 0xff); |
| 497 | write_reg(ioaddr, TxCNT1, length >> 8); |
| 498 | write_reg(ioaddr, CMR1, CMR1_Xmit); |
| 499 | } |
| 500 | |
| 501 | static void write_packet(long ioaddr, int length, unsigned char *packet, int pad_len, int data_mode) |
| 502 | { |
| 503 | if (length & 1) |
| 504 | { |
| 505 | length++; |
| 506 | pad_len++; |
| 507 | } |
| 508 | |
| 509 | outb(EOC+MAR, ioaddr + PAR_DATA); |
| 510 | if ((data_mode & 1) == 0) { |
| 511 | /* Write the packet out, starting with the write addr. */ |
| 512 | outb(WrAddr+MAR, ioaddr + PAR_DATA); |
| 513 | do { |
| 514 | write_byte_mode0(ioaddr, *packet++); |
| 515 | } while (--length > pad_len) ; |
| 516 | do { |
| 517 | write_byte_mode0(ioaddr, 0); |
| 518 | } while (--length > 0) ; |
| 519 | } else { |
| 520 | /* Write the packet out in slow mode. */ |
| 521 | unsigned char outbyte = *packet++; |
| 522 | |
| 523 | outb(Ctrl_LNibWrite + Ctrl_IRQEN, ioaddr + PAR_CONTROL); |
| 524 | outb(WrAddr+MAR, ioaddr + PAR_DATA); |
| 525 | |
| 526 | outb((outbyte & 0x0f)|0x40, ioaddr + PAR_DATA); |
| 527 | outb(outbyte & 0x0f, ioaddr + PAR_DATA); |
| 528 | outbyte >>= 4; |
| 529 | outb(outbyte & 0x0f, ioaddr + PAR_DATA); |
| 530 | outb(Ctrl_HNibWrite + Ctrl_IRQEN, ioaddr + PAR_CONTROL); |
| 531 | while (--length > pad_len) |
| 532 | write_byte_mode1(ioaddr, *packet++); |
| 533 | while (--length > 0) |
| 534 | write_byte_mode1(ioaddr, 0); |
| 535 | } |
| 536 | /* Terminate the Tx frame. End of write: ECB. */ |
| 537 | outb(0xff, ioaddr + PAR_DATA); |
| 538 | outb(Ctrl_HNibWrite | Ctrl_SelData | Ctrl_IRQEN, ioaddr + PAR_CONTROL); |
| 539 | } |
| 540 | |
| 541 | static void tx_timeout(struct net_device *dev) |
| 542 | { |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 543 | long ioaddr = dev->base_addr; |
| 544 | |
| 545 | printk(KERN_WARNING "%s: Transmit timed out, %s?\n", dev->name, |
| 546 | inb(ioaddr + PAR_CONTROL) & 0x10 ? "network cable problem" |
| 547 | : "IRQ conflict"); |
Jeff Garzik | 09f75cd | 2007-10-03 17:41:50 -0700 | [diff] [blame] | 548 | dev->stats.tx_errors++; |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 549 | /* Try to restart the adapter. */ |
| 550 | hardware_init(dev); |
| 551 | dev->trans_start = jiffies; |
| 552 | netif_wake_queue(dev); |
Jeff Garzik | 09f75cd | 2007-10-03 17:41:50 -0700 | [diff] [blame] | 553 | dev->stats.tx_errors++; |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 554 | } |
| 555 | |
Stephen Hemminger | 61357325 | 2009-08-31 19:50:58 +0000 | [diff] [blame] | 556 | static netdev_tx_t atp_send_packet(struct sk_buff *skb, |
| 557 | struct net_device *dev) |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 558 | { |
| 559 | struct net_local *lp = netdev_priv(dev); |
| 560 | long ioaddr = dev->base_addr; |
| 561 | int length; |
| 562 | unsigned long flags; |
| 563 | |
| 564 | length = ETH_ZLEN < skb->len ? skb->len : ETH_ZLEN; |
| 565 | |
| 566 | netif_stop_queue(dev); |
| 567 | |
| 568 | /* Disable interrupts by writing 0x00 to the Interrupt Mask Register. |
| 569 | This sequence must not be interrupted by an incoming packet. */ |
| 570 | |
| 571 | spin_lock_irqsave(&lp->lock, flags); |
| 572 | write_reg(ioaddr, IMR, 0); |
| 573 | write_reg_high(ioaddr, IMR, 0); |
| 574 | spin_unlock_irqrestore(&lp->lock, flags); |
| 575 | |
| 576 | write_packet(ioaddr, length, skb->data, length-skb->len, dev->if_port); |
| 577 | |
| 578 | lp->pac_cnt_in_tx_buf++; |
| 579 | if (lp->tx_unit_busy == 0) { |
| 580 | trigger_send(ioaddr, length); |
| 581 | lp->saved_tx_size = 0; /* Redundant */ |
| 582 | lp->re_tx = 0; |
| 583 | lp->tx_unit_busy = 1; |
| 584 | } else |
| 585 | lp->saved_tx_size = length; |
| 586 | /* Re-enable the LPT interrupts. */ |
| 587 | write_reg(ioaddr, IMR, ISR_RxOK | ISR_TxErr | ISR_TxOK); |
| 588 | write_reg_high(ioaddr, IMR, ISRh_RxErr); |
| 589 | |
| 590 | dev->trans_start = jiffies; |
| 591 | dev_kfree_skb (skb); |
Patrick McHardy | 6ed1065 | 2009-06-23 06:03:08 +0000 | [diff] [blame] | 592 | return NETDEV_TX_OK; |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 593 | } |
| 594 | |
| 595 | |
| 596 | /* The typical workload of the driver: |
| 597 | Handle the network interface interrupts. */ |
David Howells | 7d12e78 | 2006-10-05 14:55:46 +0100 | [diff] [blame] | 598 | static irqreturn_t atp_interrupt(int irq, void *dev_instance) |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 599 | { |
Jeff Garzik | c31f28e | 2006-10-06 14:56:04 -0400 | [diff] [blame] | 600 | struct net_device *dev = dev_instance; |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 601 | struct net_local *lp; |
| 602 | long ioaddr; |
| 603 | static int num_tx_since_rx; |
| 604 | int boguscount = max_interrupt_work; |
| 605 | int handled = 0; |
| 606 | |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 607 | ioaddr = dev->base_addr; |
| 608 | lp = netdev_priv(dev); |
| 609 | |
| 610 | spin_lock(&lp->lock); |
| 611 | |
| 612 | /* Disable additional spurious interrupts. */ |
| 613 | outb(Ctrl_SelData, ioaddr + PAR_CONTROL); |
| 614 | |
| 615 | /* The adapter's output is currently the IRQ line, switch it to data. */ |
| 616 | write_reg(ioaddr, CMR2, CMR2_NULL); |
| 617 | write_reg(ioaddr, IMR, 0); |
| 618 | |
| 619 | if (net_debug > 5) printk(KERN_DEBUG "%s: In interrupt ", dev->name); |
| 620 | while (--boguscount > 0) { |
| 621 | int status = read_nibble(ioaddr, ISR); |
| 622 | if (net_debug > 5) printk("loop status %02x..", status); |
| 623 | |
| 624 | if (status & (ISR_RxOK<<3)) { |
| 625 | handled = 1; |
| 626 | write_reg(ioaddr, ISR, ISR_RxOK); /* Clear the Rx interrupt. */ |
| 627 | do { |
| 628 | int read_status = read_nibble(ioaddr, CMR1); |
| 629 | if (net_debug > 6) |
| 630 | printk("handling Rx packet %02x..", read_status); |
| 631 | /* We acknowledged the normal Rx interrupt, so if the interrupt |
| 632 | is still outstanding we must have a Rx error. */ |
| 633 | if (read_status & (CMR1_IRQ << 3)) { /* Overrun. */ |
Jeff Garzik | 09f75cd | 2007-10-03 17:41:50 -0700 | [diff] [blame] | 634 | dev->stats.rx_over_errors++; |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 635 | /* Set to no-accept mode long enough to remove a packet. */ |
| 636 | write_reg_high(ioaddr, CMR2, CMR2h_OFF); |
| 637 | net_rx(dev); |
| 638 | /* Clear the interrupt and return to normal Rx mode. */ |
| 639 | write_reg_high(ioaddr, ISR, ISRh_RxErr); |
| 640 | write_reg_high(ioaddr, CMR2, lp->addr_mode); |
| 641 | } else if ((read_status & (CMR1_BufEnb << 3)) == 0) { |
| 642 | net_rx(dev); |
| 643 | num_tx_since_rx = 0; |
| 644 | } else |
| 645 | break; |
| 646 | } while (--boguscount > 0); |
| 647 | } else if (status & ((ISR_TxErr + ISR_TxOK)<<3)) { |
| 648 | handled = 1; |
| 649 | if (net_debug > 6) printk("handling Tx done.."); |
| 650 | /* Clear the Tx interrupt. We should check for too many failures |
| 651 | and reinitialize the adapter. */ |
| 652 | write_reg(ioaddr, ISR, ISR_TxErr + ISR_TxOK); |
| 653 | if (status & (ISR_TxErr<<3)) { |
Jeff Garzik | 09f75cd | 2007-10-03 17:41:50 -0700 | [diff] [blame] | 654 | dev->stats.collisions++; |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 655 | if (++lp->re_tx > 15) { |
Jeff Garzik | 09f75cd | 2007-10-03 17:41:50 -0700 | [diff] [blame] | 656 | dev->stats.tx_aborted_errors++; |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 657 | hardware_init(dev); |
| 658 | break; |
| 659 | } |
| 660 | /* Attempt to retransmit. */ |
| 661 | if (net_debug > 6) printk("attempting to ReTx"); |
| 662 | write_reg(ioaddr, CMR1, CMR1_ReXmit + CMR1_Xmit); |
| 663 | } else { |
| 664 | /* Finish up the transmit. */ |
Jeff Garzik | 09f75cd | 2007-10-03 17:41:50 -0700 | [diff] [blame] | 665 | dev->stats.tx_packets++; |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 666 | lp->pac_cnt_in_tx_buf--; |
| 667 | if ( lp->saved_tx_size) { |
| 668 | trigger_send(ioaddr, lp->saved_tx_size); |
| 669 | lp->saved_tx_size = 0; |
| 670 | lp->re_tx = 0; |
| 671 | } else |
| 672 | lp->tx_unit_busy = 0; |
| 673 | netif_wake_queue(dev); /* Inform upper layers. */ |
| 674 | } |
| 675 | num_tx_since_rx++; |
Joe Perches | 8e95a20 | 2009-12-03 07:58:21 +0000 | [diff] [blame] | 676 | } else if (num_tx_since_rx > 8 && |
| 677 | time_after(jiffies, dev->last_rx + HZ)) { |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 678 | if (net_debug > 2) |
| 679 | printk(KERN_DEBUG "%s: Missed packet? No Rx after %d Tx and " |
| 680 | "%ld jiffies status %02x CMR1 %02x.\n", dev->name, |
| 681 | num_tx_since_rx, jiffies - dev->last_rx, status, |
| 682 | (read_nibble(ioaddr, CMR1) >> 3) & 15); |
Jeff Garzik | 09f75cd | 2007-10-03 17:41:50 -0700 | [diff] [blame] | 683 | dev->stats.rx_missed_errors++; |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 684 | hardware_init(dev); |
| 685 | num_tx_since_rx = 0; |
| 686 | break; |
| 687 | } else |
| 688 | break; |
| 689 | } |
| 690 | |
| 691 | /* This following code fixes a rare (and very difficult to track down) |
| 692 | problem where the adapter forgets its ethernet address. */ |
| 693 | { |
| 694 | int i; |
| 695 | for (i = 0; i < 6; i++) |
| 696 | write_reg_byte(ioaddr, PAR0 + i, dev->dev_addr[i]); |
| 697 | #if 0 && defined(TIMED_CHECKER) |
| 698 | mod_timer(&lp->timer, jiffies + TIMED_CHECKER); |
| 699 | #endif |
| 700 | } |
| 701 | |
| 702 | /* Tell the adapter that it can go back to using the output line as IRQ. */ |
| 703 | write_reg(ioaddr, CMR2, CMR2_IRQOUT); |
| 704 | /* Enable the physical interrupt line, which is sure to be low until.. */ |
| 705 | outb(Ctrl_SelData + Ctrl_IRQEN, ioaddr + PAR_CONTROL); |
| 706 | /* .. we enable the interrupt sources. */ |
| 707 | write_reg(ioaddr, IMR, ISR_RxOK | ISR_TxErr | ISR_TxOK); |
| 708 | write_reg_high(ioaddr, IMR, ISRh_RxErr); /* Hmmm, really needed? */ |
| 709 | |
| 710 | spin_unlock(&lp->lock); |
| 711 | |
| 712 | if (net_debug > 5) printk("exiting interrupt.\n"); |
| 713 | return IRQ_RETVAL(handled); |
| 714 | } |
| 715 | |
| 716 | #ifdef TIMED_CHECKER |
| 717 | /* This following code fixes a rare (and very difficult to track down) |
| 718 | problem where the adapter forgets its ethernet address. */ |
| 719 | static void atp_timed_checker(unsigned long data) |
| 720 | { |
| 721 | struct net_device *dev = (struct net_device *)data; |
| 722 | long ioaddr = dev->base_addr; |
| 723 | struct net_local *lp = netdev_priv(dev); |
| 724 | int tickssofar = jiffies - lp->last_rx_time; |
| 725 | int i; |
| 726 | |
| 727 | spin_lock(&lp->lock); |
| 728 | if (tickssofar > 2*HZ) { |
| 729 | #if 1 |
| 730 | for (i = 0; i < 6; i++) |
| 731 | write_reg_byte(ioaddr, PAR0 + i, dev->dev_addr[i]); |
| 732 | lp->last_rx_time = jiffies; |
| 733 | #else |
| 734 | for (i = 0; i < 6; i++) |
| 735 | if (read_cmd_byte(ioaddr, PAR0 + i) != atp_timed_dev->dev_addr[i]) |
| 736 | { |
| 737 | struct net_local *lp = netdev_priv(atp_timed_dev); |
| 738 | write_reg_byte(ioaddr, PAR0 + i, atp_timed_dev->dev_addr[i]); |
| 739 | if (i == 2) |
Jeff Garzik | 09f75cd | 2007-10-03 17:41:50 -0700 | [diff] [blame] | 740 | dev->stats.tx_errors++; |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 741 | else if (i == 3) |
Jeff Garzik | 09f75cd | 2007-10-03 17:41:50 -0700 | [diff] [blame] | 742 | dev->stats.tx_dropped++; |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 743 | else if (i == 4) |
Jeff Garzik | 09f75cd | 2007-10-03 17:41:50 -0700 | [diff] [blame] | 744 | dev->stats.collisions++; |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 745 | else |
Jeff Garzik | 09f75cd | 2007-10-03 17:41:50 -0700 | [diff] [blame] | 746 | dev->stats.rx_errors++; |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 747 | } |
| 748 | #endif |
| 749 | } |
| 750 | spin_unlock(&lp->lock); |
| 751 | lp->timer.expires = jiffies + TIMED_CHECKER; |
| 752 | add_timer(&lp->timer); |
| 753 | } |
| 754 | #endif |
| 755 | |
| 756 | /* We have a good packet(s), get it/them out of the buffers. */ |
| 757 | static void net_rx(struct net_device *dev) |
| 758 | { |
| 759 | struct net_local *lp = netdev_priv(dev); |
| 760 | long ioaddr = dev->base_addr; |
| 761 | struct rx_header rx_head; |
| 762 | |
| 763 | /* Process the received packet. */ |
| 764 | outb(EOC+MAR, ioaddr + PAR_DATA); |
| 765 | read_block(ioaddr, 8, (unsigned char*)&rx_head, dev->if_port); |
| 766 | if (net_debug > 5) |
| 767 | printk(KERN_DEBUG " rx_count %04x %04x %04x %04x..", rx_head.pad, |
| 768 | rx_head.rx_count, rx_head.rx_status, rx_head.cur_addr); |
| 769 | if ((rx_head.rx_status & 0x77) != 0x01) { |
Jeff Garzik | 09f75cd | 2007-10-03 17:41:50 -0700 | [diff] [blame] | 770 | dev->stats.rx_errors++; |
| 771 | if (rx_head.rx_status & 0x0004) dev->stats.rx_frame_errors++; |
| 772 | else if (rx_head.rx_status & 0x0002) dev->stats.rx_crc_errors++; |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 773 | if (net_debug > 3) |
| 774 | printk(KERN_DEBUG "%s: Unknown ATP Rx error %04x.\n", |
| 775 | dev->name, rx_head.rx_status); |
| 776 | if (rx_head.rx_status & 0x0020) { |
Jeff Garzik | 09f75cd | 2007-10-03 17:41:50 -0700 | [diff] [blame] | 777 | dev->stats.rx_fifo_errors++; |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 778 | write_reg_high(ioaddr, CMR1, CMR1h_TxENABLE); |
| 779 | write_reg_high(ioaddr, CMR1, CMR1h_RxENABLE | CMR1h_TxENABLE); |
| 780 | } else if (rx_head.rx_status & 0x0050) |
| 781 | hardware_init(dev); |
| 782 | return; |
| 783 | } else { |
| 784 | /* Malloc up new buffer. The "-4" omits the FCS (CRC). */ |
| 785 | int pkt_len = (rx_head.rx_count & 0x7ff) - 4; |
| 786 | struct sk_buff *skb; |
| 787 | |
| 788 | skb = dev_alloc_skb(pkt_len + 2); |
| 789 | if (skb == NULL) { |
| 790 | printk(KERN_ERR "%s: Memory squeeze, dropping packet.\n", |
| 791 | dev->name); |
Jeff Garzik | 09f75cd | 2007-10-03 17:41:50 -0700 | [diff] [blame] | 792 | dev->stats.rx_dropped++; |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 793 | goto done; |
| 794 | } |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 795 | |
| 796 | skb_reserve(skb, 2); /* Align IP on 16 byte boundaries */ |
| 797 | read_block(ioaddr, pkt_len, skb_put(skb,pkt_len), dev->if_port); |
| 798 | skb->protocol = eth_type_trans(skb, dev); |
| 799 | netif_rx(skb); |
| 800 | dev->last_rx = jiffies; |
Jeff Garzik | 09f75cd | 2007-10-03 17:41:50 -0700 | [diff] [blame] | 801 | dev->stats.rx_packets++; |
| 802 | dev->stats.rx_bytes += pkt_len; |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 803 | } |
| 804 | done: |
| 805 | write_reg(ioaddr, CMR1, CMR1_NextPkt); |
| 806 | lp->last_rx_time = jiffies; |
| 807 | return; |
| 808 | } |
| 809 | |
| 810 | static void read_block(long ioaddr, int length, unsigned char *p, int data_mode) |
| 811 | { |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 812 | if (data_mode <= 3) { /* Mode 0 or 1 */ |
| 813 | outb(Ctrl_LNibRead, ioaddr + PAR_CONTROL); |
| 814 | outb(length == 8 ? RdAddr | HNib | MAR : RdAddr | MAR, |
| 815 | ioaddr + PAR_DATA); |
| 816 | if (data_mode <= 1) { /* Mode 0 or 1 */ |
Hannes Eder | e4c3c13 | 2008-12-25 23:55:35 -0800 | [diff] [blame] | 817 | do { *p++ = read_byte_mode0(ioaddr); } while (--length > 0); |
| 818 | } else { /* Mode 2 or 3 */ |
| 819 | do { *p++ = read_byte_mode2(ioaddr); } while (--length > 0); |
| 820 | } |
| 821 | } else if (data_mode <= 5) { |
| 822 | do { *p++ = read_byte_mode4(ioaddr); } while (--length > 0); |
| 823 | } else { |
| 824 | do { *p++ = read_byte_mode6(ioaddr); } while (--length > 0); |
| 825 | } |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 826 | |
Hannes Eder | e4c3c13 | 2008-12-25 23:55:35 -0800 | [diff] [blame] | 827 | outb(EOC+HNib+MAR, ioaddr + PAR_DATA); |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 828 | outb(Ctrl_SelData, ioaddr + PAR_CONTROL); |
| 829 | } |
| 830 | |
| 831 | /* The inverse routine to net_open(). */ |
| 832 | static int |
| 833 | net_close(struct net_device *dev) |
| 834 | { |
| 835 | struct net_local *lp = netdev_priv(dev); |
| 836 | long ioaddr = dev->base_addr; |
| 837 | |
| 838 | netif_stop_queue(dev); |
| 839 | |
| 840 | del_timer_sync(&lp->timer); |
| 841 | |
| 842 | /* Flush the Tx and disable Rx here. */ |
| 843 | lp->addr_mode = CMR2h_OFF; |
| 844 | write_reg_high(ioaddr, CMR2, CMR2h_OFF); |
| 845 | |
| 846 | /* Free the IRQ line. */ |
| 847 | outb(0x00, ioaddr + PAR_CONTROL); |
| 848 | free_irq(dev->irq, dev); |
| 849 | |
| 850 | /* Reset the ethernet hardware and activate the printer pass-through. */ |
| 851 | write_reg_high(ioaddr, CMR1, CMR1h_RESET | CMR1h_MUX); |
| 852 | return 0; |
| 853 | } |
| 854 | |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 855 | /* |
| 856 | * Set or clear the multicast filter for this adapter. |
| 857 | */ |
| 858 | |
| 859 | static void set_rx_mode_8002(struct net_device *dev) |
| 860 | { |
| 861 | struct net_local *lp = netdev_priv(dev); |
| 862 | long ioaddr = dev->base_addr; |
| 863 | |
Wang Chen | c16d118 | 2008-07-22 13:13:12 +0800 | [diff] [blame] | 864 | if (dev->mc_count > 0 || (dev->flags & (IFF_ALLMULTI|IFF_PROMISC))) |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 865 | lp->addr_mode = CMR2h_PROMISC; |
Wang Chen | c16d118 | 2008-07-22 13:13:12 +0800 | [diff] [blame] | 866 | else |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 867 | lp->addr_mode = CMR2h_Normal; |
| 868 | write_reg_high(ioaddr, CMR2, lp->addr_mode); |
| 869 | } |
| 870 | |
| 871 | static void set_rx_mode_8012(struct net_device *dev) |
| 872 | { |
| 873 | struct net_local *lp = netdev_priv(dev); |
| 874 | long ioaddr = dev->base_addr; |
| 875 | unsigned char new_mode, mc_filter[8]; /* Multicast hash filter */ |
| 876 | int i; |
| 877 | |
| 878 | if (dev->flags & IFF_PROMISC) { /* Set promiscuous. */ |
| 879 | new_mode = CMR2h_PROMISC; |
| 880 | } else if ((dev->mc_count > 1000) || (dev->flags & IFF_ALLMULTI)) { |
| 881 | /* Too many to filter perfectly -- accept all multicasts. */ |
| 882 | memset(mc_filter, 0xff, sizeof(mc_filter)); |
| 883 | new_mode = CMR2h_Normal; |
| 884 | } else { |
| 885 | struct dev_mc_list *mclist; |
| 886 | |
| 887 | memset(mc_filter, 0, sizeof(mc_filter)); |
| 888 | for (i = 0, mclist = dev->mc_list; mclist && i < dev->mc_count; |
| 889 | i++, mclist = mclist->next) |
| 890 | { |
| 891 | int filterbit = ether_crc_le(ETH_ALEN, mclist->dmi_addr) & 0x3f; |
| 892 | mc_filter[filterbit >> 5] |= 1 << (filterbit & 31); |
| 893 | } |
| 894 | new_mode = CMR2h_Normal; |
| 895 | } |
| 896 | lp->addr_mode = new_mode; |
| 897 | write_reg(ioaddr, CMR2, CMR2_IRQOUT | 0x04); /* Switch to page 1. */ |
| 898 | for (i = 0; i < 8; i++) |
| 899 | write_reg_byte(ioaddr, i, mc_filter[i]); |
| 900 | if (net_debug > 2 || 1) { |
| 901 | lp->addr_mode = 1; |
| 902 | printk(KERN_DEBUG "%s: Mode %d, setting multicast filter to", |
| 903 | dev->name, lp->addr_mode); |
| 904 | for (i = 0; i < 8; i++) |
| 905 | printk(" %2.2x", mc_filter[i]); |
| 906 | printk(".\n"); |
| 907 | } |
| 908 | |
| 909 | write_reg_high(ioaddr, CMR2, lp->addr_mode); |
| 910 | write_reg(ioaddr, CMR2, CMR2_IRQOUT); /* Switch back to page 0 */ |
| 911 | } |
| 912 | |
Stephen Hemminger | 3a1a27f | 2009-01-07 18:10:24 -0800 | [diff] [blame] | 913 | static void set_rx_mode(struct net_device *dev) |
| 914 | { |
| 915 | struct net_local *lp = netdev_priv(dev); |
| 916 | |
| 917 | if (lp->chip_type == RTL8002) |
| 918 | return set_rx_mode_8002(dev); |
| 919 | else |
| 920 | return set_rx_mode_8012(dev); |
| 921 | } |
| 922 | |
| 923 | |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 924 | static int __init atp_init_module(void) { |
| 925 | if (debug) /* Emit version even if no cards detected. */ |
Markus Dahms | 2c2a8c5 | 2007-05-09 07:58:10 +0200 | [diff] [blame] | 926 | printk(KERN_INFO "%s", version); |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 927 | return atp_init(); |
| 928 | } |
| 929 | |
| 930 | static void __exit atp_cleanup_module(void) { |
| 931 | struct net_device *next_dev; |
| 932 | |
| 933 | while (root_atp_dev) { |
Wang Chen | 454d7c9 | 2008-11-12 23:37:49 -0800 | [diff] [blame] | 934 | struct net_local *atp_local = netdev_priv(root_atp_dev); |
| 935 | next_dev = atp_local->next_module; |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 936 | unregister_netdev(root_atp_dev); |
| 937 | /* No need to release_region(), since we never snarf it. */ |
| 938 | free_netdev(root_atp_dev); |
| 939 | root_atp_dev = next_dev; |
| 940 | } |
| 941 | } |
| 942 | |
| 943 | module_init(atp_init_module); |
| 944 | module_exit(atp_cleanup_module); |