blob: 56e890df5053605a8eb7a66514eb096d0e110b2d [file] [log] [blame]
Linus Torvalds1da177e2005-04-16 15:20:36 -07001config H8300
2 bool
3 default y
Sam Ravnborgec7748b2008-02-09 10:46:40 +01004 select HAVE_IDE
Thomas Gleixner51f3f152011-01-19 12:26:32 +01005 select HAVE_GENERIC_HARDIRQS
Thomas Gleixner9f7b2182011-03-24 19:15:36 +01006 select GENERIC_IRQ_SHOW
Ben Hutchings9f13a1f2012-01-10 03:04:32 +00007 select GENERIC_CPU_DEVICES
Linus Torvalds1da177e2005-04-16 15:20:36 -07008
Alan Jenkins9e1b9b82009-11-07 21:03:54 +00009config SYMBOL_PREFIX
10 string
11 default "_"
12
Linus Torvalds1da177e2005-04-16 15:20:36 -070013config MMU
14 bool
15 default n
16
17config SWAP
18 bool
19 default n
20
Christoph Lameter66701b12007-02-10 01:43:09 -080021config ZONE_DMA
22 bool
23 default y
24
Linus Torvalds1da177e2005-04-16 15:20:36 -070025config FPU
26 bool
27 default n
28
Linus Torvalds1da177e2005-04-16 15:20:36 -070029config RWSEM_GENERIC_SPINLOCK
30 bool
31 default y
32
33config RWSEM_XCHGADD_ALGORITHM
34 bool
35 default n
36
David Howellsf0d1b0b2006-12-08 02:37:49 -080037config ARCH_HAS_ILOG2_U32
38 bool
39 default n
40
41config ARCH_HAS_ILOG2_U64
42 bool
43 default n
44
Akinobu Mitaf6e02132006-03-26 01:39:23 -080045config GENERIC_HWEIGHT
46 bool
47 default y
48
Linus Torvalds1da177e2005-04-16 15:20:36 -070049config GENERIC_CALIBRATE_DELAY
50 bool
51 default y
52
Yoshinori Sato9791af52008-10-15 22:01:17 -070053config GENERIC_BUG
54 bool
55 depends on BUG
56
Ingo Molnar06027bd2006-02-14 13:53:15 -080057config TIME_LOW_RES
58 bool
59 default y
60
Al Viro5ea81762007-02-11 15:41:31 +000061config NO_IOPORT
62 def_bool y
63
Dan Williams1b0fac42007-07-15 23:40:26 -070064config NO_DMA
65 def_bool y
66
Linus Torvalds1da177e2005-04-16 15:20:36 -070067config ISA
68 bool
69 default y
70
71config PCI
72 bool
73 default n
74
H. Peter Anvinbdc80782008-02-08 04:21:26 -080075config HZ
76 int
77 default 100
78
Linus Torvalds1da177e2005-04-16 15:20:36 -070079source "init/Kconfig"
80
Matt Helsleydc52ddc2008-10-18 20:27:21 -070081source "kernel/Kconfig.freezer"
82
Linus Torvalds1da177e2005-04-16 15:20:36 -070083source "arch/h8300/Kconfig.cpu"
84
85menu "Executable file formats"
86
87source "fs/Kconfig.binfmt"
88
89endmenu
90
Sam Ravnborgd5950b42005-07-11 21:03:49 -070091source "net/Kconfig"
92
Linus Torvalds1da177e2005-04-16 15:20:36 -070093source "drivers/base/Kconfig"
94
95source "drivers/mtd/Kconfig"
96
97source "drivers/block/Kconfig"
98
99source "drivers/ide/Kconfig"
100
101source "arch/h8300/Kconfig.ide"
102
Sam Ravnborgd5950b42005-07-11 21:03:49 -0700103source "drivers/net/Kconfig"
Linus Torvalds1da177e2005-04-16 15:20:36 -0700104
105#
106# input - input/joystick depends on it. As does USB.
107#
108source "drivers/input/Kconfig"
109
110menu "Character devices"
111
112config VT
113 bool "Virtual terminal"
114 ---help---
115 If you say Y here, you will get support for terminal devices with
116 display and keyboard devices. These are called "virtual" because you
117 can run several virtual terminals (also called virtual consoles) on
118 one physical terminal. This is rather useful, for example one
119 virtual terminal can collect system messages and warnings, another
120 one can be used for a text-mode user session, and a third could run
121 an X session, all in parallel. Switching between virtual terminals
122 is done with certain key combinations, usually Alt-<function key>.
123
124 The setterm command ("man setterm") can be used to change the
125 properties (such as colors or beeping) of a virtual terminal. The
126 man page console_codes(4) ("man console_codes") contains the special
127 character sequences that can be used to change those properties
128 directly. The fonts used on virtual terminals can be changed with
129 the setfont ("man setfont") command and the key bindings are defined
130 with the loadkeys ("man loadkeys") command.
131
132 You need at least one virtual terminal device in order to make use
133 of your keyboard and monitor. Therefore, only people configuring an
134 embedded system would want to say N here in order to save some
135 memory; the only way to log into such a system is then via a serial
136 or network connection.
137
138 If unsure, say Y, or else you won't be able to do much with your new
139 shiny Linux system :-)
140
141config VT_CONSOLE
142 bool "Support for console on virtual terminal"
143 depends on VT
144 ---help---
145 The system console is the device which receives all kernel messages
146 and warnings and which allows logins in single user mode. If you
147 answer Y here, a virtual terminal (the device used to interact with
148 a physical terminal) can be used as system console. This is the most
149 common mode of operations, so you should say Y here unless you want
150 the kernel messages be output only to a serial port (in which case
151 you should say Y to "Console on serial port", below).
152
153 If you do say Y here, by default the currently visible virtual
154 terminal (/dev/tty0) will be used as system console. You can change
155 that with a kernel command line option such as "console=tty3" which
156 would use the third virtual terminal as system console. (Try "man
157 bootparam" or see the documentation of your boot loader (lilo or
158 loadlin) about how to pass options to the kernel at boot time.)
159
160 If unsure, say Y.
161
162config HW_CONSOLE
163 bool
Paul Bolle75330692011-10-12 14:25:31 +0200164 depends on VT
Linus Torvalds1da177e2005-04-16 15:20:36 -0700165 default y
166
167comment "Unix98 PTY support"
168
169config UNIX98_PTYS
170 bool "Unix98 PTY support"
171 ---help---
172 A pseudo terminal (PTY) is a software device consisting of two
173 halves: a master and a slave. The slave device behaves identical to
174 a physical terminal; the master device is used by a process to
175 read data from and write data to the slave, thereby emulating a
176 terminal. Typical programs for the master side are telnet servers
177 and xterms.
178
179 Linux has traditionally used the BSD-like names /dev/ptyxx for
180 masters and /dev/ttyxx for slaves of pseudo terminals. This scheme
181 has a number of problems. The GNU C library glibc 2.1 and later,
182 however, supports the Unix98 naming standard: in order to acquire a
183 pseudo terminal, a process opens /dev/ptmx; the number of the pseudo
184 terminal is then made available to the process and the pseudo
185 terminal slave can be accessed as /dev/pts/<number>. What was
186 traditionally /dev/ttyp2 will then be /dev/pts/2, for example.
187
188 The entries in /dev/pts/ are created on the fly by a virtual
189 file system; therefore, if you say Y here you should say Y to
190 "/dev/pts file system for Unix98 PTYs" as well.
191
192 If you want to say Y here, you need to have the C library glibc 2.1
193 or later (equal to libc-6.1, check with "ls -l /lib/libc.so.*").
194 Read the instructions in <file:Documentation/Changes> pertaining to
195 pseudo terminals. It's safe to say N.
196
Linus Torvalds1da177e2005-04-16 15:20:36 -0700197source "drivers/char/pcmcia/Kconfig"
198
Paul Bollea4a77b12011-10-11 13:23:29 +0200199source "drivers/tty/serial/Kconfig"
Linus Torvalds1da177e2005-04-16 15:20:36 -0700200
201source "drivers/i2c/Kconfig"
202
Jean Delvaread2f9312005-07-02 18:15:49 +0200203source "drivers/hwmon/Kconfig"
204
Linus Torvalds1da177e2005-04-16 15:20:36 -0700205source "drivers/usb/Kconfig"
206
Greg Kroah-Hartman2f86c3e2008-09-17 16:34:11 +0100207source "drivers/uwb/Kconfig"
208
Linus Torvalds1da177e2005-04-16 15:20:36 -0700209endmenu
210
F. Duncan M. Haldane6e38a2b2008-11-07 18:17:51 -0500211source "drivers/staging/Kconfig"
212
Linus Torvalds1da177e2005-04-16 15:20:36 -0700213source "fs/Kconfig"
214
Linus Torvalds1da177e2005-04-16 15:20:36 -0700215source "arch/h8300/Kconfig.debug"
216
217source "security/Kconfig"
218
219source "crypto/Kconfig"
220
221source "lib/Kconfig"