| Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 1 | /* |
| 2 | * Trantor T128/T128F/T228 defines |
| 3 | * Note : architecturally, the T100 and T128 are different and won't work |
| 4 | * |
| 5 | * Copyright 1993, Drew Eckhardt |
| 6 | * Visionary Computing |
| 7 | * (Unix and Linux consulting and custom programming) |
| 8 | * drew@colorado.edu |
| 9 | * +1 (303) 440-4894 |
| 10 | * |
| 11 | * DISTRIBUTION RELEASE 3. |
| 12 | * |
| 13 | * For more information, please consult |
| 14 | * |
| 15 | * Trantor Systems, Ltd. |
| 16 | * T128/T128F/T228 SCSI Host Adapter |
| 17 | * Hardware Specifications |
| 18 | * |
| 19 | * Trantor Systems, Ltd. |
| 20 | * 5415 Randall Place |
| 21 | * Fremont, CA 94538 |
| 22 | * 1+ (415) 770-1400, FAX 1+ (415) 770-9910 |
| 23 | * |
| 24 | * and |
| 25 | * |
| 26 | * NCR 5380 Family |
| 27 | * SCSI Protocol Controller |
| 28 | * Databook |
| 29 | * |
| 30 | * NCR Microelectronics |
| 31 | * 1635 Aeroplaza Drive |
| 32 | * Colorado Springs, CO 80916 |
| 33 | * 1+ (719) 578-3400 |
| 34 | * 1+ (800) 334-5454 |
| 35 | */ |
| 36 | |
| 37 | /* |
| 38 | * $Log: t128.h,v $ |
| 39 | */ |
| 40 | |
| 41 | #ifndef T128_H |
| 42 | #define T128_H |
| 43 | |
| 44 | #define T128_PUBLIC_RELEASE 3 |
| 45 | |
| 46 | #define TDEBUG_INIT 0x1 |
| 47 | #define TDEBUG_TRANSFER 0x2 |
| 48 | |
| 49 | /* |
| 50 | * The trantor boards are memory mapped. They use an NCR5380 or |
| 51 | * equivalent (my sample board had part second sourced from ZILOG). |
| 52 | * NCR's recommended "Pseudo-DMA" architecture is used, where |
| 53 | * a PAL drives the DMA signals on the 5380 allowing fast, blind |
| 54 | * transfers with proper handshaking. |
| 55 | */ |
| 56 | |
| 57 | /* |
| 58 | * Note : a boot switch is provided for the purpose of informing the |
| 59 | * firmware to boot or not boot from attached SCSI devices. So, I imagine |
| 60 | * there are fewer people who've yanked the ROM like they do on the Seagate |
| 61 | * to make bootup faster, and I'll probably use this for autodetection. |
| 62 | */ |
| 63 | #define T_ROM_OFFSET 0 |
| 64 | |
| 65 | /* |
| 66 | * Note : my sample board *WAS NOT* populated with the SRAM, so this |
| 67 | * can't be used for autodetection without a ROM present. |
| 68 | */ |
| 69 | #define T_RAM_OFFSET 0x1800 |
| 70 | |
| 71 | /* |
| 72 | * All of the registers are allocated 32 bytes of address space, except |
| 73 | * for the data register (read/write to/from the 5380 in pseudo-DMA mode) |
| 74 | */ |
| 75 | #define T_CONTROL_REG_OFFSET 0x1c00 /* rw */ |
| 76 | #define T_CR_INT 0x10 /* Enable interrupts */ |
| 77 | #define T_CR_CT 0x02 /* Reset watchdog timer */ |
| 78 | |
| 79 | #define T_STATUS_REG_OFFSET 0x1c20 /* ro */ |
| 80 | #define T_ST_BOOT 0x80 /* Boot switch */ |
| 81 | #define T_ST_S3 0x40 /* User settable switches, */ |
| 82 | #define T_ST_S2 0x20 /* read 0 when switch is on, 1 off */ |
| 83 | #define T_ST_S1 0x10 |
| 84 | #define T_ST_PS2 0x08 /* Set for Microchannel 228 */ |
| 85 | #define T_ST_RDY 0x04 /* 5380 DRQ */ |
| 86 | #define T_ST_TIM 0x02 /* indicates 40us watchdog timer fired */ |
| 87 | #define T_ST_ZERO 0x01 /* Always zero */ |
| 88 | |
| 89 | #define T_5380_OFFSET 0x1d00 /* 8 registers here, see NCR5380.h */ |
| 90 | |
| 91 | #define T_DATA_REG_OFFSET 0x1e00 /* rw 512 bytes long */ |
| 92 | |
| 93 | #ifndef ASM |
| 94 | static int t128_abort(Scsi_Cmnd *); |
| 95 | static int t128_biosparam(struct scsi_device *, struct block_device *, |
| 96 | sector_t, int*); |
| 97 | static int t128_detect(Scsi_Host_Template *); |
| 98 | static int t128_queue_command(Scsi_Cmnd *, void (*done)(Scsi_Cmnd *)); |
| 99 | static int t128_host_reset(Scsi_Cmnd *); |
| 100 | static int t128_bus_reset(Scsi_Cmnd *); |
| 101 | static int t128_device_reset(Scsi_Cmnd *); |
| 102 | |
| 103 | #ifndef CMD_PER_LUN |
| 104 | #define CMD_PER_LUN 2 |
| 105 | #endif |
| 106 | |
| 107 | #ifndef CAN_QUEUE |
| 108 | #define CAN_QUEUE 32 |
| 109 | #endif |
| 110 | |
| 111 | #ifndef HOSTS_C |
| 112 | |
| 113 | #define NCR5380_implementation_fields \ |
| 114 | void __iomem *base |
| 115 | |
| 116 | #define NCR5380_local_declare() \ |
| 117 | void __iomem *base |
| 118 | |
| 119 | #define NCR5380_setup(instance) \ |
| 120 | base = ((struct NCR5380_hostdata *)(instance->hostdata))->base |
| 121 | |
| 122 | #define T128_address(reg) (base + T_5380_OFFSET + ((reg) * 0x20)) |
| 123 | |
| 124 | #if !(TDEBUG & TDEBUG_TRANSFER) |
| 125 | #define NCR5380_read(reg) readb(T128_address(reg)) |
| 126 | #define NCR5380_write(reg, value) writeb((value),(T128_address(reg))) |
| 127 | #else |
| 128 | #define NCR5380_read(reg) \ |
| 129 | (((unsigned char) printk("scsi%d : read register %d at address %08x\n"\ |
| 130 | , instance->hostno, (reg), T128_address(reg))), readb(T128_address(reg))) |
| 131 | |
| 132 | #define NCR5380_write(reg, value) { \ |
| 133 | printk("scsi%d : write %02x to register %d at address %08x\n", \ |
| 134 | instance->hostno, (value), (reg), T128_address(reg)); \ |
| 135 | writeb((value), (T128_address(reg))); \ |
| 136 | } |
| 137 | #endif |
| 138 | |
| 139 | #define NCR5380_intr t128_intr |
| 140 | #define do_NCR5380_intr do_t128_intr |
| 141 | #define NCR5380_queue_command t128_queue_command |
| 142 | #define NCR5380_abort t128_abort |
| 143 | #define NCR5380_host_reset t128_host_reset |
| 144 | #define NCR5380_device_reset t128_device_reset |
| 145 | #define NCR5380_bus_reset t128_bus_reset |
| 146 | #define NCR5380_proc_info t128_proc_info |
| 147 | |
| 148 | /* 15 14 12 10 7 5 3 |
| 149 | 1101 0100 1010 1000 */ |
| 150 | |
| 151 | #define T128_IRQS 0xc4a8 |
| 152 | |
| 153 | #endif /* else def HOSTS_C */ |
| 154 | #endif /* ndef ASM */ |
| 155 | #endif /* T128_H */ |