blob: 01457b266f3d18b3aeccaa827863f37fd9ae1c85 [file] [log] [blame]
Jeff Garzik669a5db2006-08-29 18:12:40 -04001/*
2 * Libata driver for the highpoint 372N and 302N UDMA66 ATA controllers.
3 *
4 * This driver is heavily based upon:
5 *
6 * linux/drivers/ide/pci/hpt366.c Version 0.36 April 25, 2003
7 *
8 * Copyright (C) 1999-2003 Andre Hedrick <andre@linux-ide.org>
9 * Portions Copyright (C) 2001 Sun Microsystems, Inc.
10 * Portions Copyright (C) 2003 Red Hat Inc
Sergei Shtylyov256ace92009-12-17 01:11:27 -050011 * Portions Copyright (C) 2005-2009 MontaVista Software, Inc.
Jeff Garzik669a5db2006-08-29 18:12:40 -040012 *
13 *
14 * TODO
Jeff Garzik669a5db2006-08-29 18:12:40 -040015 * Work out best PLL policy
16 */
17
18#include <linux/kernel.h>
19#include <linux/module.h>
20#include <linux/pci.h>
21#include <linux/init.h>
22#include <linux/blkdev.h>
23#include <linux/delay.h>
24#include <scsi/scsi_host.h>
25#include <linux/libata.h>
26
27#define DRV_NAME "pata_hpt3x2n"
Sergei Shtylyov1a1b1722009-12-07 23:30:06 +040028#define DRV_VERSION "0.3.10"
Jeff Garzik669a5db2006-08-29 18:12:40 -040029
30enum {
31 HPT_PCI_FAST = (1 << 31),
32 PCI66 = (1 << 1),
33 USE_DPLL = (1 << 0)
34};
35
36struct hpt_clock {
37 u8 xfer_speed;
38 u32 timing;
39};
40
41struct hpt_chip {
42 const char *name;
43 struct hpt_clock *clocks[3];
44};
45
46/* key for bus clock timings
47 * bit
Sergei Shtylyovfd5e62e2009-12-07 23:38:11 +040048 * 0:3 data_high_time. Inactive time of DIOW_/DIOR_ for PIO and MW DMA.
49 * cycles = value + 1
50 * 4:8 data_low_time. Active time of DIOW_/DIOR_ for PIO and MW DMA.
51 * cycles = value + 1
52 * 9:12 cmd_high_time. Inactive time of DIOW_/DIOR_ during task file
Jeff Garzik669a5db2006-08-29 18:12:40 -040053 * register access.
Sergei Shtylyovfd5e62e2009-12-07 23:38:11 +040054 * 13:17 cmd_low_time. Active time of DIOW_/DIOR_ during task file
Jeff Garzik669a5db2006-08-29 18:12:40 -040055 * register access.
Sergei Shtylyovfd5e62e2009-12-07 23:38:11 +040056 * 18:20 udma_cycle_time. Clock cycles for UDMA xfer.
57 * 21 CLK frequency for UDMA: 0=ATA clock, 1=dual ATA clock.
58 * 22:24 pre_high_time. Time to initialize 1st cycle for PIO and MW DMA xfer.
59 * 25:27 cmd_pre_high_time. Time to initialize 1st PIO cycle for task file
Jeff Garzik669a5db2006-08-29 18:12:40 -040060 * register access.
Sergei Shtylyovfd5e62e2009-12-07 23:38:11 +040061 * 28 UDMA enable.
62 * 29 DMA enable.
63 * 30 PIO_MST enable. If set, the chip is in bus master mode during
64 * PIO xfer.
65 * 31 FIFO enable. Only for PIO.
Jeff Garzik669a5db2006-08-29 18:12:40 -040066 */
Jeff Garzik85cd7252006-08-31 00:03:49 -040067
Jeff Garzik669a5db2006-08-29 18:12:40 -040068/* 66MHz DPLL clocks */
69
70static struct hpt_clock hpt3x2n_clocks[] = {
71 { XFER_UDMA_7, 0x1c869c62 },
72 { XFER_UDMA_6, 0x1c869c62 },
73 { XFER_UDMA_5, 0x1c8a9c62 },
74 { XFER_UDMA_4, 0x1c8a9c62 },
75 { XFER_UDMA_3, 0x1c8e9c62 },
76 { XFER_UDMA_2, 0x1c929c62 },
77 { XFER_UDMA_1, 0x1c9a9c62 },
78 { XFER_UDMA_0, 0x1c829c62 },
79
80 { XFER_MW_DMA_2, 0x2c829c62 },
81 { XFER_MW_DMA_1, 0x2c829c66 },
Bartlomiej Zolnierkiewiczd413ff32009-12-03 20:32:09 +010082 { XFER_MW_DMA_0, 0x2c829d2e },
Jeff Garzik669a5db2006-08-29 18:12:40 -040083
84 { XFER_PIO_4, 0x0c829c62 },
85 { XFER_PIO_3, 0x0c829c84 },
86 { XFER_PIO_2, 0x0c829ca6 },
87 { XFER_PIO_1, 0x0d029d26 },
88 { XFER_PIO_0, 0x0d029d5e },
Jeff Garzik669a5db2006-08-29 18:12:40 -040089};
90
91/**
92 * hpt3x2n_find_mode - reset the hpt3x2n bus
93 * @ap: ATA port
94 * @speed: transfer mode
95 *
96 * Return the 32bit register programming information for this channel
97 * that matches the speed provided. For the moment the clocks table
98 * is hard coded but easy to change. This will be needed if we use
99 * different DPLLs
100 */
Jeff Garzik85cd7252006-08-31 00:03:49 -0400101
Jeff Garzik669a5db2006-08-29 18:12:40 -0400102static u32 hpt3x2n_find_mode(struct ata_port *ap, int speed)
103{
104 struct hpt_clock *clocks = hpt3x2n_clocks;
Jeff Garzik85cd7252006-08-31 00:03:49 -0400105
Jeff Garzik669a5db2006-08-29 18:12:40 -0400106 while(clocks->xfer_speed) {
107 if (clocks->xfer_speed == speed)
108 return clocks->timing;
109 clocks++;
110 }
111 BUG();
112 return 0xffffffffU; /* silence compiler warning */
113}
114
115/**
Jeff Garzika0fcdc02007-03-09 07:24:15 -0500116 * hpt3x2n_cable_detect - Detect the cable type
117 * @ap: ATA port to detect on
Jeff Garzik669a5db2006-08-29 18:12:40 -0400118 *
Jeff Garzika0fcdc02007-03-09 07:24:15 -0500119 * Return the cable type attached to this port
Jeff Garzik669a5db2006-08-29 18:12:40 -0400120 */
Jeff Garzik85cd7252006-08-31 00:03:49 -0400121
Jeff Garzika0fcdc02007-03-09 07:24:15 -0500122static int hpt3x2n_cable_detect(struct ata_port *ap)
Jeff Garzik669a5db2006-08-29 18:12:40 -0400123{
124 u8 scr2, ata66;
125 struct pci_dev *pdev = to_pci_dev(ap->host->dev);
Jeff Garzik85cd7252006-08-31 00:03:49 -0400126
Jeff Garzik669a5db2006-08-29 18:12:40 -0400127 pci_read_config_byte(pdev, 0x5B, &scr2);
128 pci_write_config_byte(pdev, 0x5B, scr2 & ~0x01);
Bartlomiej Zolnierkiewicz10a9c962009-11-19 20:31:31 +0100129
130 udelay(10); /* debounce */
131
Jeff Garzik669a5db2006-08-29 18:12:40 -0400132 /* Cable register now active */
133 pci_read_config_byte(pdev, 0x5A, &ata66);
134 /* Restore state */
135 pci_write_config_byte(pdev, 0x5B, scr2);
Jeff Garzik85cd7252006-08-31 00:03:49 -0400136
Bartlomiej Zolnierkiewiczf3b1cf42009-11-19 18:38:11 +0100137 if (ata66 & (2 >> ap->port_no))
Jeff Garzika0fcdc02007-03-09 07:24:15 -0500138 return ATA_CBL_PATA40;
Jeff Garzik669a5db2006-08-29 18:12:40 -0400139 else
Jeff Garzika0fcdc02007-03-09 07:24:15 -0500140 return ATA_CBL_PATA80;
141}
Jeff Garzik669a5db2006-08-29 18:12:40 -0400142
Jeff Garzika0fcdc02007-03-09 07:24:15 -0500143/**
144 * hpt3x2n_pre_reset - reset the hpt3x2n bus
Tejun Heocc0680a2007-08-06 18:36:23 +0900145 * @link: ATA link to reset
Alan Cox28e21c82007-04-26 00:19:25 -0700146 * @deadline: deadline jiffies for the operation
Jeff Garzika0fcdc02007-03-09 07:24:15 -0500147 *
148 * Perform the initial reset handling for the 3x2n series controllers.
149 * Reset the hardware and state machine,
150 */
151
Tejun Heoa1efdab2008-03-25 12:22:50 +0900152static int hpt3x2n_pre_reset(struct ata_link *link, unsigned long deadline)
Jeff Garzika0fcdc02007-03-09 07:24:15 -0500153{
Tejun Heocc0680a2007-08-06 18:36:23 +0900154 struct ata_port *ap = link->ap;
Jeff Garzika0fcdc02007-03-09 07:24:15 -0500155 struct pci_dev *pdev = to_pci_dev(ap->host->dev);
Jeff Garzik669a5db2006-08-29 18:12:40 -0400156 /* Reset the state machine */
Alan Cox28e21c82007-04-26 00:19:25 -0700157 pci_write_config_byte(pdev, 0x50 + 4 * ap->port_no, 0x37);
Jeff Garzik669a5db2006-08-29 18:12:40 -0400158 udelay(100);
Tejun Heod4b2bab2007-02-02 16:50:52 +0900159
Tejun Heo9363c382008-04-07 22:47:16 +0900160 return ata_sff_prereset(link, deadline);
Jeff Garzik669a5db2006-08-29 18:12:40 -0400161}
Jeff Garzik85cd7252006-08-31 00:03:49 -0400162
Sergei Shtylyov1a1b1722009-12-07 23:30:06 +0400163static void hpt3x2n_set_mode(struct ata_port *ap, struct ata_device *adev,
164 u8 mode)
165{
166 struct pci_dev *pdev = to_pci_dev(ap->host->dev);
167 u32 addr1, addr2;
168 u32 reg, timing, mask;
169 u8 fast;
170
171 addr1 = 0x40 + 4 * (adev->devno + 2 * ap->port_no);
172 addr2 = 0x51 + 4 * ap->port_no;
173
174 /* Fast interrupt prediction disable, hold off interrupt disable */
175 pci_read_config_byte(pdev, addr2, &fast);
176 fast &= ~0x07;
177 pci_write_config_byte(pdev, addr2, fast);
178
179 /* Determine timing mask and find matching mode entry */
180 if (mode < XFER_MW_DMA_0)
181 mask = 0xcfc3ffff;
182 else if (mode < XFER_UDMA_0)
183 mask = 0x31c001ff;
184 else
185 mask = 0x303c0000;
186
187 timing = hpt3x2n_find_mode(ap, mode);
188
189 pci_read_config_dword(pdev, addr1, &reg);
190 reg = (reg & ~mask) | (timing & mask);
191 pci_write_config_dword(pdev, addr1, reg);
192}
193
Jeff Garzik669a5db2006-08-29 18:12:40 -0400194/**
Jeff Garzik669a5db2006-08-29 18:12:40 -0400195 * hpt3x2n_set_piomode - PIO setup
196 * @ap: ATA interface
197 * @adev: device on the interface
198 *
Jeff Garzik85cd7252006-08-31 00:03:49 -0400199 * Perform PIO mode setup.
Jeff Garzik669a5db2006-08-29 18:12:40 -0400200 */
Jeff Garzik85cd7252006-08-31 00:03:49 -0400201
Jeff Garzik669a5db2006-08-29 18:12:40 -0400202static void hpt3x2n_set_piomode(struct ata_port *ap, struct ata_device *adev)
203{
Sergei Shtylyov1a1b1722009-12-07 23:30:06 +0400204 hpt3x2n_set_mode(ap, adev, adev->pio_mode);
Jeff Garzik669a5db2006-08-29 18:12:40 -0400205}
206
207/**
208 * hpt3x2n_set_dmamode - DMA timing setup
209 * @ap: ATA interface
210 * @adev: Device being configured
211 *
Sergei Shtylyov1a1b1722009-12-07 23:30:06 +0400212 * Set up the channel for MWDMA or UDMA modes.
Jeff Garzik669a5db2006-08-29 18:12:40 -0400213 */
Jeff Garzik85cd7252006-08-31 00:03:49 -0400214
Jeff Garzik669a5db2006-08-29 18:12:40 -0400215static void hpt3x2n_set_dmamode(struct ata_port *ap, struct ata_device *adev)
216{
Sergei Shtylyov1a1b1722009-12-07 23:30:06 +0400217 hpt3x2n_set_mode(ap, adev, adev->dma_mode);
Jeff Garzik669a5db2006-08-29 18:12:40 -0400218}
219
220/**
221 * hpt3x2n_bmdma_end - DMA engine stop
222 * @qc: ATA command
223 *
224 * Clean up after the HPT3x2n and later DMA engine
225 */
Jeff Garzik85cd7252006-08-31 00:03:49 -0400226
Jeff Garzik669a5db2006-08-29 18:12:40 -0400227static void hpt3x2n_bmdma_stop(struct ata_queued_cmd *qc)
228{
229 struct ata_port *ap = qc->ap;
230 struct pci_dev *pdev = to_pci_dev(ap->host->dev);
231 int mscreg = 0x50 + 2 * ap->port_no;
232 u8 bwsr_stat, msc_stat;
Jeff Garzik85cd7252006-08-31 00:03:49 -0400233
Jeff Garzik669a5db2006-08-29 18:12:40 -0400234 pci_read_config_byte(pdev, 0x6A, &bwsr_stat);
235 pci_read_config_byte(pdev, mscreg, &msc_stat);
236 if (bwsr_stat & (1 << ap->port_no))
237 pci_write_config_byte(pdev, mscreg, msc_stat | 0x30);
238 ata_bmdma_stop(qc);
239}
240
241/**
242 * hpt3x2n_set_clock - clock control
243 * @ap: ATA port
244 * @source: 0x21 or 0x23 for PLL or PCI sourced clock
245 *
246 * Switch the ATA bus clock between the PLL and PCI clock sources
247 * while correctly isolating the bus and resetting internal logic
248 *
249 * We must use the DPLL for
250 * - writing
251 * - second channel UDMA7 (SATA ports) or higher
252 * - 66MHz PCI
Jeff Garzik85cd7252006-08-31 00:03:49 -0400253 *
Jeff Garzik669a5db2006-08-29 18:12:40 -0400254 * or we will underclock the device and get reduced performance.
255 */
Jeff Garzik85cd7252006-08-31 00:03:49 -0400256
Jeff Garzik669a5db2006-08-29 18:12:40 -0400257static void hpt3x2n_set_clock(struct ata_port *ap, int source)
258{
Sergei Shtylyov256ace92009-12-17 01:11:27 -0500259 void __iomem *bmdma = ap->ioaddr.bmdma_addr - ap->port_no * 8;
Jeff Garzik85cd7252006-08-31 00:03:49 -0400260
Jeff Garzik669a5db2006-08-29 18:12:40 -0400261 /* Tristate the bus */
Tejun Heo0d5ff562007-02-01 15:06:36 +0900262 iowrite8(0x80, bmdma+0x73);
263 iowrite8(0x80, bmdma+0x77);
Jeff Garzik85cd7252006-08-31 00:03:49 -0400264
Jeff Garzik669a5db2006-08-29 18:12:40 -0400265 /* Switch clock and reset channels */
Tejun Heo0d5ff562007-02-01 15:06:36 +0900266 iowrite8(source, bmdma+0x7B);
267 iowrite8(0xC0, bmdma+0x79);
Jeff Garzik85cd7252006-08-31 00:03:49 -0400268
Sergei Shtylyov256ace92009-12-17 01:11:27 -0500269 /* Reset state machines, avoid enabling the disabled channels */
270 iowrite8(ioread8(bmdma+0x70) | 0x32, bmdma+0x70);
271 iowrite8(ioread8(bmdma+0x74) | 0x32, bmdma+0x74);
Jeff Garzik85cd7252006-08-31 00:03:49 -0400272
Jeff Garzik669a5db2006-08-29 18:12:40 -0400273 /* Complete reset */
Tejun Heo0d5ff562007-02-01 15:06:36 +0900274 iowrite8(0x00, bmdma+0x79);
Jeff Garzik85cd7252006-08-31 00:03:49 -0400275
Jeff Garzik669a5db2006-08-29 18:12:40 -0400276 /* Reconnect channels to bus */
Tejun Heo0d5ff562007-02-01 15:06:36 +0900277 iowrite8(0x00, bmdma+0x73);
278 iowrite8(0x00, bmdma+0x77);
Jeff Garzik669a5db2006-08-29 18:12:40 -0400279}
280
Alana52865c2007-01-24 11:51:38 +0000281static int hpt3x2n_use_dpll(struct ata_port *ap, int writing)
Jeff Garzik669a5db2006-08-29 18:12:40 -0400282{
283 long flags = (long)ap->host->private_data;
Sergei Shtylyov256ace92009-12-17 01:11:27 -0500284
Jeff Garzik669a5db2006-08-29 18:12:40 -0400285 /* See if we should use the DPLL */
Alana52865c2007-01-24 11:51:38 +0000286 if (writing)
Jeff Garzik669a5db2006-08-29 18:12:40 -0400287 return USE_DPLL; /* Needed for write */
288 if (flags & PCI66)
289 return USE_DPLL; /* Needed at 66Mhz */
Jeff Garzik85cd7252006-08-31 00:03:49 -0400290 return 0;
Jeff Garzik669a5db2006-08-29 18:12:40 -0400291}
292
Sergei Shtylyov256ace92009-12-17 01:11:27 -0500293static int hpt3x2n_qc_defer(struct ata_queued_cmd *qc)
294{
295 struct ata_port *ap = qc->ap;
296 struct ata_port *alt = ap->host->ports[ap->port_no ^ 1];
297 int rc, flags = (long)ap->host->private_data;
298 int dpll = hpt3x2n_use_dpll(ap, qc->tf.flags & ATA_TFLAG_WRITE);
299
300 /* First apply the usual rules */
301 rc = ata_std_qc_defer(qc);
302 if (rc != 0)
303 return rc;
304
305 if ((flags & USE_DPLL) != dpll && alt->qc_active)
306 return ATA_DEFER_PORT;
307 return 0;
308}
309
Tejun Heo9363c382008-04-07 22:47:16 +0900310static unsigned int hpt3x2n_qc_issue(struct ata_queued_cmd *qc)
Jeff Garzik669a5db2006-08-29 18:12:40 -0400311{
Jeff Garzik669a5db2006-08-29 18:12:40 -0400312 struct ata_port *ap = qc->ap;
313 int flags = (long)ap->host->private_data;
Sergei Shtylyov256ace92009-12-17 01:11:27 -0500314 int dpll = hpt3x2n_use_dpll(ap, qc->tf.flags & ATA_TFLAG_WRITE);
Jeff Garzik85cd7252006-08-31 00:03:49 -0400315
Sergei Shtylyov256ace92009-12-17 01:11:27 -0500316 if ((flags & USE_DPLL) != dpll) {
317 flags &= ~USE_DPLL;
318 flags |= dpll;
319 ap->host->private_data = (void *)(long)flags;
320
321 hpt3x2n_set_clock(ap, dpll ? 0x21 : 0x23);
Jeff Garzik669a5db2006-08-29 18:12:40 -0400322 }
Tejun Heo9363c382008-04-07 22:47:16 +0900323 return ata_sff_qc_issue(qc);
Jeff Garzik669a5db2006-08-29 18:12:40 -0400324}
325
326static struct scsi_host_template hpt3x2n_sht = {
Tejun Heo68d1d072008-03-25 12:22:49 +0900327 ATA_BMDMA_SHT(DRV_NAME),
Jeff Garzik669a5db2006-08-29 18:12:40 -0400328};
329
330/*
331 * Configuration for HPT3x2n.
332 */
Jeff Garzik85cd7252006-08-31 00:03:49 -0400333
Jeff Garzik669a5db2006-08-29 18:12:40 -0400334static struct ata_port_operations hpt3x2n_port_ops = {
Tejun Heo029cfd62008-03-25 12:22:49 +0900335 .inherits = &ata_bmdma_port_ops,
Jeff Garzik85cd7252006-08-31 00:03:49 -0400336
Jeff Garzik669a5db2006-08-29 18:12:40 -0400337 .bmdma_stop = hpt3x2n_bmdma_stop,
Sergei Shtylyov256ace92009-12-17 01:11:27 -0500338
339 .qc_defer = hpt3x2n_qc_defer,
Tejun Heo9363c382008-04-07 22:47:16 +0900340 .qc_issue = hpt3x2n_qc_issue,
Jeff Garzikbda30282006-09-27 05:41:13 -0400341
Tejun Heo029cfd62008-03-25 12:22:49 +0900342 .cable_detect = hpt3x2n_cable_detect,
343 .set_piomode = hpt3x2n_set_piomode,
344 .set_dmamode = hpt3x2n_set_dmamode,
Tejun Heoa1efdab2008-03-25 12:22:50 +0900345 .prereset = hpt3x2n_pre_reset,
Jeff Garzik85cd7252006-08-31 00:03:49 -0400346};
Jeff Garzik669a5db2006-08-29 18:12:40 -0400347
348/**
349 * hpt3xn_calibrate_dpll - Calibrate the DPLL loop
Jeff Garzik85cd7252006-08-31 00:03:49 -0400350 * @dev: PCI device
Jeff Garzik669a5db2006-08-29 18:12:40 -0400351 *
352 * Perform a calibration cycle on the HPT3xN DPLL. Returns 1 if this
353 * succeeds
354 */
355
356static int hpt3xn_calibrate_dpll(struct pci_dev *dev)
357{
358 u8 reg5b;
359 u32 reg5c;
360 int tries;
Jeff Garzik85cd7252006-08-31 00:03:49 -0400361
Jeff Garzik669a5db2006-08-29 18:12:40 -0400362 for(tries = 0; tries < 0x5000; tries++) {
363 udelay(50);
364 pci_read_config_byte(dev, 0x5b, &reg5b);
365 if (reg5b & 0x80) {
366 /* See if it stays set */
367 for(tries = 0; tries < 0x1000; tries ++) {
368 pci_read_config_byte(dev, 0x5b, &reg5b);
369 /* Failed ? */
370 if ((reg5b & 0x80) == 0)
371 return 0;
372 }
373 /* Turn off tuning, we have the DPLL set */
374 pci_read_config_dword(dev, 0x5c, &reg5c);
375 pci_write_config_dword(dev, 0x5c, reg5c & ~ 0x100);
376 return 1;
377 }
378 }
379 /* Never went stable */
380 return 0;
381}
382
383static int hpt3x2n_pci_clock(struct pci_dev *pdev)
384{
385 unsigned long freq;
386 u32 fcnt;
Alan Cox28e21c82007-04-26 00:19:25 -0700387 unsigned long iobase = pci_resource_start(pdev, 4);
Jeff Garzik85cd7252006-08-31 00:03:49 -0400388
Alan Cox28e21c82007-04-26 00:19:25 -0700389 fcnt = inl(iobase + 0x90); /* Not PCI readable for some chips */
Jeff Garzik669a5db2006-08-29 18:12:40 -0400390 if ((fcnt >> 12) != 0xABCDE) {
391 printk(KERN_WARNING "hpt3xn: BIOS clock data not set.\n");
392 return 33; /* Not BIOS set */
393 }
394 fcnt &= 0x1FF;
Jeff Garzik85cd7252006-08-31 00:03:49 -0400395
Jeff Garzik669a5db2006-08-29 18:12:40 -0400396 freq = (fcnt * 77) / 192;
Jeff Garzik85cd7252006-08-31 00:03:49 -0400397
Jeff Garzik669a5db2006-08-29 18:12:40 -0400398 /* Clamp to bands */
399 if (freq < 40)
400 return 33;
401 if (freq < 45)
402 return 40;
403 if (freq < 55)
404 return 50;
405 return 66;
406}
407
408/**
409 * hpt3x2n_init_one - Initialise an HPT37X/302
410 * @dev: PCI device
411 * @id: Entry in match table
412 *
413 * Initialise an HPT3x2n device. There are some interesting complications
414 * here. Firstly the chip may report 366 and be one of several variants.
415 * Secondly all the timings depend on the clock for the chip which we must
416 * detect and look up
417 *
418 * This is the known chip mappings. It may be missing a couple of later
419 * releases.
420 *
421 * Chip version PCI Rev Notes
422 * HPT372 4 (HPT366) 5 Other driver
423 * HPT372N 4 (HPT366) 6 UDMA133
424 * HPT372 5 (HPT372) 1 Other driver
425 * HPT372N 5 (HPT372) 2 UDMA133
426 * HPT302 6 (HPT302) * Other driver
427 * HPT302N 6 (HPT302) > 1 UDMA133
428 * HPT371 7 (HPT371) * Other driver
429 * HPT371N 7 (HPT371) > 1 UDMA133
430 * HPT374 8 (HPT374) * Other driver
431 * HPT372N 9 (HPT372N) * UDMA133
432 *
433 * (1) UDMA133 support depends on the bus clock
434 *
435 * To pin down HPT371N
436 */
Jeff Garzik85cd7252006-08-31 00:03:49 -0400437
Jeff Garzik669a5db2006-08-29 18:12:40 -0400438static int hpt3x2n_init_one(struct pci_dev *dev, const struct pci_device_id *id)
439{
440 /* HPT372N and friends - UDMA133 */
Tejun Heo1626aeb2007-05-04 12:43:58 +0200441 static const struct ata_port_info info = {
Jeff Garzik1d2808f2007-05-28 06:59:48 -0400442 .flags = ATA_FLAG_SLAVE_POSS,
Erik Inge Bolsø14bdef92009-03-14 21:38:24 +0100443 .pio_mask = ATA_PIO4,
444 .mwdma_mask = ATA_MWDMA2,
Jeff Garzikbf6263a2007-07-09 12:16:50 -0400445 .udma_mask = ATA_UDMA6,
Jeff Garzik669a5db2006-08-29 18:12:40 -0400446 .port_ops = &hpt3x2n_port_ops
447 };
Tejun Heo887125e2008-03-25 12:22:49 +0900448 const struct ata_port_info *ppi[] = { &info, NULL };
Sergei Shtylyov89d3b362009-11-24 22:54:49 +0400449 u8 rev = dev->revision;
Jeff Garzik669a5db2006-08-29 18:12:40 -0400450 u8 irqmask;
Jeff Garzik669a5db2006-08-29 18:12:40 -0400451 unsigned int pci_mhz;
452 unsigned int f_low, f_high;
453 int adjust;
Alan Cox28e21c82007-04-26 00:19:25 -0700454 unsigned long iobase = pci_resource_start(dev, 4);
Sergei Shtylyov256ace92009-12-17 01:11:27 -0500455 void *hpriv = (void *)USE_DPLL;
Tejun Heof08048e2008-03-25 12:22:47 +0900456 int rc;
457
458 rc = pcim_enable_device(dev);
459 if (rc)
460 return rc;
Jeff Garzik85cd7252006-08-31 00:03:49 -0400461
Jeff Garzik669a5db2006-08-29 18:12:40 -0400462 switch(dev->device) {
463 case PCI_DEVICE_ID_TTI_HPT366:
Sergei Shtylyov89d3b362009-11-24 22:54:49 +0400464 if (rev < 6)
Jeff Garzik669a5db2006-08-29 18:12:40 -0400465 return -ENODEV;
466 break;
Alan Cox28e21c82007-04-26 00:19:25 -0700467 case PCI_DEVICE_ID_TTI_HPT371:
Sergei Shtylyov89d3b362009-11-24 22:54:49 +0400468 if (rev < 2)
Alan Cox28e21c82007-04-26 00:19:25 -0700469 return -ENODEV;
470 /* 371N if rev > 1 */
471 break;
Jeff Garzik669a5db2006-08-29 18:12:40 -0400472 case PCI_DEVICE_ID_TTI_HPT372:
Alan Cox824cf332007-05-21 14:57:01 +0100473 /* 372N if rev >= 2*/
Sergei Shtylyov89d3b362009-11-24 22:54:49 +0400474 if (rev < 2)
Jeff Garzik669a5db2006-08-29 18:12:40 -0400475 return -ENODEV;
476 break;
477 case PCI_DEVICE_ID_TTI_HPT302:
Sergei Shtylyov89d3b362009-11-24 22:54:49 +0400478 if (rev < 2)
Jeff Garzik669a5db2006-08-29 18:12:40 -0400479 return -ENODEV;
480 break;
481 case PCI_DEVICE_ID_TTI_HPT372N:
482 break;
483 default:
484 printk(KERN_ERR "pata_hpt3x2n: PCI table is bogus please report (%d).\n", dev->device);
485 return -ENODEV;
486 }
487
488 /* Ok so this is a chip we support */
489
490 pci_write_config_byte(dev, PCI_CACHE_LINE_SIZE, (L1_CACHE_BYTES / 4));
491 pci_write_config_byte(dev, PCI_LATENCY_TIMER, 0x78);
492 pci_write_config_byte(dev, PCI_MIN_GNT, 0x08);
493 pci_write_config_byte(dev, PCI_MAX_LAT, 0x08);
494
495 pci_read_config_byte(dev, 0x5A, &irqmask);
496 irqmask &= ~0x10;
497 pci_write_config_byte(dev, 0x5a, irqmask);
498
Alan Cox28e21c82007-04-26 00:19:25 -0700499 /*
500 * HPT371 chips physically have only one channel, the secondary one,
501 * but the primary channel registers do exist! Go figure...
502 * So, we manually disable the non-existing channel here
503 * (if the BIOS hasn't done this already).
504 */
505 if (dev->device == PCI_DEVICE_ID_TTI_HPT371) {
506 u8 mcr1;
507 pci_read_config_byte(dev, 0x50, &mcr1);
508 mcr1 &= ~0x04;
509 pci_write_config_byte(dev, 0x50, mcr1);
510 }
511
Jeff Garzik669a5db2006-08-29 18:12:40 -0400512 /* Tune the PLL. HPT recommend using 75 for SATA, 66 for UDMA133 or
513 50 for UDMA100. Right now we always use 66 */
Jeff Garzik85cd7252006-08-31 00:03:49 -0400514
Jeff Garzik669a5db2006-08-29 18:12:40 -0400515 pci_mhz = hpt3x2n_pci_clock(dev);
Jeff Garzik85cd7252006-08-31 00:03:49 -0400516
Jeff Garzik669a5db2006-08-29 18:12:40 -0400517 f_low = (pci_mhz * 48) / 66; /* PCI Mhz for 66Mhz DPLL */
518 f_high = f_low + 2; /* Tolerance */
Jeff Garzik85cd7252006-08-31 00:03:49 -0400519
Jeff Garzik669a5db2006-08-29 18:12:40 -0400520 pci_write_config_dword(dev, 0x5C, (f_high << 16) | f_low | 0x100);
521 /* PLL clock */
522 pci_write_config_byte(dev, 0x5B, 0x21);
Jeff Garzik85cd7252006-08-31 00:03:49 -0400523
Jeff Garzik669a5db2006-08-29 18:12:40 -0400524 /* Unlike the 37x we don't try jiggling the frequency */
525 for(adjust = 0; adjust < 8; adjust++) {
526 if (hpt3xn_calibrate_dpll(dev))
527 break;
528 pci_write_config_dword(dev, 0x5C, (f_high << 16) | f_low);
529 }
Alan Cox28e21c82007-04-26 00:19:25 -0700530 if (adjust == 8) {
Sergei Shtylyov80b89872007-08-10 21:02:15 +0400531 printk(KERN_ERR "pata_hpt3x2n: DPLL did not stabilize!\n");
Alan Cox28e21c82007-04-26 00:19:25 -0700532 return -ENODEV;
533 }
Jeff Garzik669a5db2006-08-29 18:12:40 -0400534
Sergei Shtylyov80b89872007-08-10 21:02:15 +0400535 printk(KERN_INFO "pata_hpt37x: bus clock %dMHz, using 66MHz DPLL.\n",
536 pci_mhz);
Jeff Garzik669a5db2006-08-29 18:12:40 -0400537 /* Set our private data up. We only need a few flags so we use
538 it directly */
Sergei Shtylyov60661932009-12-07 23:25:52 +0400539 if (pci_mhz > 60)
Sergei Shtylyov256ace92009-12-17 01:11:27 -0500540 hpriv = (void *)(PCI66 | USE_DPLL);
Sergei Shtylyov60661932009-12-07 23:25:52 +0400541
542 /*
543 * On HPT371N, if ATA clock is 66 MHz we must set bit 2 in
544 * the MISC. register to stretch the UltraDMA Tss timing.
545 * NOTE: This register is only writeable via I/O space.
546 */
547 if (dev->device == PCI_DEVICE_ID_TTI_HPT371)
548 outb(inb(iobase + 0x9c) | 0x04, iobase + 0x9c);
Jeff Garzik85cd7252006-08-31 00:03:49 -0400549
Jeff Garzik669a5db2006-08-29 18:12:40 -0400550 /* Now kick off ATA set up */
Alan Cox16ea0fc2010-02-23 02:26:06 -0500551 return ata_pci_sff_init_one(dev, ppi, &hpt3x2n_sht, hpriv, 0);
Jeff Garzik669a5db2006-08-29 18:12:40 -0400552}
553
Jeff Garzik2d2744f2006-09-28 20:21:59 -0400554static const struct pci_device_id hpt3x2n[] = {
555 { PCI_VDEVICE(TTI, PCI_DEVICE_ID_TTI_HPT366), },
Alan Cox28e21c82007-04-26 00:19:25 -0700556 { PCI_VDEVICE(TTI, PCI_DEVICE_ID_TTI_HPT371), },
Jeff Garzik2d2744f2006-09-28 20:21:59 -0400557 { PCI_VDEVICE(TTI, PCI_DEVICE_ID_TTI_HPT372), },
558 { PCI_VDEVICE(TTI, PCI_DEVICE_ID_TTI_HPT302), },
559 { PCI_VDEVICE(TTI, PCI_DEVICE_ID_TTI_HPT372N), },
560
561 { },
Jeff Garzik669a5db2006-08-29 18:12:40 -0400562};
563
564static struct pci_driver hpt3x2n_pci_driver = {
Jeff Garzik2d2744f2006-09-28 20:21:59 -0400565 .name = DRV_NAME,
Jeff Garzik669a5db2006-08-29 18:12:40 -0400566 .id_table = hpt3x2n,
567 .probe = hpt3x2n_init_one,
568 .remove = ata_pci_remove_one
569};
570
571static int __init hpt3x2n_init(void)
572{
573 return pci_register_driver(&hpt3x2n_pci_driver);
574}
575
Jeff Garzik669a5db2006-08-29 18:12:40 -0400576static void __exit hpt3x2n_exit(void)
577{
578 pci_unregister_driver(&hpt3x2n_pci_driver);
579}
580
Jeff Garzik669a5db2006-08-29 18:12:40 -0400581MODULE_AUTHOR("Alan Cox");
582MODULE_DESCRIPTION("low-level driver for the Highpoint HPT3x2n/30x");
583MODULE_LICENSE("GPL");
584MODULE_DEVICE_TABLE(pci, hpt3x2n);
585MODULE_VERSION(DRV_VERSION);
586
587module_init(hpt3x2n_init);
588module_exit(hpt3x2n_exit);