blob: e381b895b04d09eded85a1e2d19615e9326a47a6 [file] [log] [blame]
Bryan Wu194de562007-05-06 14:50:30 -07001/*
Mike Frysinger1ba7a3e2008-01-11 15:56:26 +08002 * Blackfin On-Chip Serial Driver
Bryan Wu194de562007-05-06 14:50:30 -07003 *
Sonic Zhang57afb392009-09-09 10:46:19 +00004 * Copyright 2006-2010 Analog Devices Inc.
Bryan Wu194de562007-05-06 14:50:30 -07005 *
Mike Frysinger1ba7a3e2008-01-11 15:56:26 +08006 * Enter bugs at http://blackfin.uclinux.org/
Bryan Wu194de562007-05-06 14:50:30 -07007 *
Mike Frysinger1ba7a3e2008-01-11 15:56:26 +08008 * Licensed under the GPL-2 or later.
Bryan Wu194de562007-05-06 14:50:30 -07009 */
10
11#if defined(CONFIG_SERIAL_BFIN_CONSOLE) && defined(CONFIG_MAGIC_SYSRQ)
12#define SUPPORT_SYSRQ
13#endif
14
Sonic Zhang57afb392009-09-09 10:46:19 +000015#define DRIVER_NAME "bfin-uart"
16#define pr_fmt(fmt) DRIVER_NAME ": " fmt
17
Bryan Wu194de562007-05-06 14:50:30 -070018#include <linux/module.h>
19#include <linux/ioport.h>
Tejun Heo5a0e3ad2010-03-24 17:04:11 +090020#include <linux/gfp.h>
Mike Frysinger599b7142010-01-19 06:13:13 -050021#include <linux/io.h>
Bryan Wu194de562007-05-06 14:50:30 -070022#include <linux/init.h>
23#include <linux/console.h>
24#include <linux/sysrq.h>
25#include <linux/platform_device.h>
26#include <linux/tty.h>
27#include <linux/tty_flip.h>
28#include <linux/serial_core.h>
Sonic Zhang57afb392009-09-09 10:46:19 +000029#include <linux/gpio.h>
30#include <linux/irq.h>
31#include <linux/kgdb.h>
32#include <linux/slab.h>
Sonic Zhangb6100992010-10-27 04:16:47 -040033#include <linux/dma-mapping.h>
Bryan Wu194de562007-05-06 14:50:30 -070034
Sonic Zhang57afb392009-09-09 10:46:19 +000035#include <asm/portmux.h>
Bryan Wu194de562007-05-06 14:50:30 -070036#include <asm/cacheflush.h>
Sonic Zhang57afb392009-09-09 10:46:19 +000037#include <asm/dma.h>
38
39#define port_membase(uart) (((struct bfin_serial_port *)(uart))->port.membase)
40#define get_lsr_cache(uart) (((struct bfin_serial_port *)(uart))->lsr)
41#define put_lsr_cache(uart, v) (((struct bfin_serial_port *)(uart))->lsr = (v))
42#include <asm/bfin_serial.h>
Bryan Wu194de562007-05-06 14:50:30 -070043
Mike Frysinger607c2682009-06-22 18:41:47 +010044#ifdef CONFIG_SERIAL_BFIN_MODULE
45# undef CONFIG_EARLY_PRINTK
46#endif
47
Mike Frysinger0271edd2009-08-06 15:20:05 -070048#ifdef CONFIG_SERIAL_BFIN_MODULE
49# undef CONFIG_EARLY_PRINTK
50#endif
51
Bryan Wu194de562007-05-06 14:50:30 -070052/* UART name and device definitions */
Sonic Zhang57afb392009-09-09 10:46:19 +000053#define BFIN_SERIAL_DEV_NAME "ttyBF"
Bryan Wu194de562007-05-06 14:50:30 -070054#define BFIN_SERIAL_MAJOR 204
55#define BFIN_SERIAL_MINOR 64
56
Sonic Zhang57afb392009-09-09 10:46:19 +000057static struct bfin_serial_port *bfin_serial_ports[BFIN_UART_NR_PORTS];
Mike Frysingerc9607ec2008-10-13 10:33:16 +010058
Sonic Zhang52e15f02009-01-02 13:40:14 +000059#if defined(CONFIG_KGDB_SERIAL_CONSOLE) || \
60 defined(CONFIG_KGDB_SERIAL_CONSOLE_MODULE)
61
62# ifndef CONFIG_SERIAL_BFIN_PIO
63# error KGDB only support UART in PIO mode.
64# endif
65
66static int kgdboc_port_line;
67static int kgdboc_break_enabled;
68#endif
Bryan Wu194de562007-05-06 14:50:30 -070069/*
70 * Setup for console. Argument comes from the menuconfig
71 */
72#define DMA_RX_XCOUNT 512
73#define DMA_RX_YCOUNT (PAGE_SIZE / DMA_RX_XCOUNT)
74
Sonic Zhang0aef4562008-02-29 12:08:42 +080075#define DMA_RX_FLUSH_JIFFIES (HZ / 50)
Bryan Wu194de562007-05-06 14:50:30 -070076
77#ifdef CONFIG_SERIAL_BFIN_DMA
78static void bfin_serial_dma_tx_chars(struct bfin_serial_port *uart);
79#else
Bryan Wu194de562007-05-06 14:50:30 -070080static void bfin_serial_tx_chars(struct bfin_serial_port *uart);
Bryan Wu194de562007-05-06 14:50:30 -070081#endif
82
Graf Yang80d5c472009-01-02 13:40:22 +000083static void bfin_serial_reset_irda(struct uart_port *port);
84
Sonic Zhangd307d362009-04-07 16:52:26 +010085#if defined(CONFIG_SERIAL_BFIN_CTSRTS) || \
86 defined(CONFIG_SERIAL_BFIN_HARD_CTSRTS)
87static unsigned int bfin_serial_get_mctrl(struct uart_port *port)
88{
89 struct bfin_serial_port *uart = (struct bfin_serial_port *)port;
90 if (uart->cts_pin < 0)
91 return TIOCM_CTS | TIOCM_DSR | TIOCM_CAR;
92
93 /* CTS PIN is negative assertive. */
94 if (UART_GET_CTS(uart))
95 return TIOCM_CTS | TIOCM_DSR | TIOCM_CAR;
96 else
97 return TIOCM_DSR | TIOCM_CAR;
98}
99
100static void bfin_serial_set_mctrl(struct uart_port *port, unsigned int mctrl)
101{
102 struct bfin_serial_port *uart = (struct bfin_serial_port *)port;
103 if (uart->rts_pin < 0)
104 return;
105
106 /* RTS PIN is negative assertive. */
107 if (mctrl & TIOCM_RTS)
108 UART_ENABLE_RTS(uart);
109 else
110 UART_DISABLE_RTS(uart);
111}
112
113/*
114 * Handle any change of modem status signal.
115 */
116static irqreturn_t bfin_serial_mctrl_cts_int(int irq, void *dev_id)
117{
118 struct bfin_serial_port *uart = dev_id;
119 unsigned int status;
120
121 status = bfin_serial_get_mctrl(&uart->port);
122 uart_handle_cts_change(&uart->port, status & TIOCM_CTS);
123#ifdef CONFIG_SERIAL_BFIN_HARD_CTSRTS
124 uart->scts = 1;
125 UART_CLEAR_SCTS(uart);
126 UART_CLEAR_IER(uart, EDSSI);
127#endif
128
129 return IRQ_HANDLED;
130}
131#else
132static unsigned int bfin_serial_get_mctrl(struct uart_port *port)
133{
134 return TIOCM_CTS | TIOCM_DSR | TIOCM_CAR;
135}
136
137static void bfin_serial_set_mctrl(struct uart_port *port, unsigned int mctrl)
138{
139}
140#endif
141
Bryan Wu194de562007-05-06 14:50:30 -0700142/*
143 * interrupts are disabled on entry
144 */
145static void bfin_serial_stop_tx(struct uart_port *port)
146{
147 struct bfin_serial_port *uart = (struct bfin_serial_port *)port;
Sonic Zhang68a784c2009-01-02 13:40:38 +0000148#ifdef CONFIG_SERIAL_BFIN_DMA
Alan Coxebd2c8f2009-09-19 13:13:28 -0700149 struct circ_buf *xmit = &uart->port.state->xmit;
Sonic Zhang68a784c2009-01-02 13:40:38 +0000150#endif
Bryan Wu194de562007-05-06 14:50:30 -0700151
Roy Huangf4d640c2007-07-12 16:43:46 +0800152 while (!(UART_GET_LSR(uart) & TEMT))
Sonic Zhang0711d852008-02-25 15:16:50 +0800153 cpu_relax();
Roy Huangf4d640c2007-07-12 16:43:46 +0800154
Bryan Wu194de562007-05-06 14:50:30 -0700155#ifdef CONFIG_SERIAL_BFIN_DMA
156 disable_dma(uart->tx_dma_channel);
Sonic Zhang0711d852008-02-25 15:16:50 +0800157 xmit->tail = (xmit->tail + uart->tx_count) & (UART_XMIT_SIZE - 1);
158 uart->port.icount.tx += uart->tx_count;
159 uart->tx_count = 0;
160 uart->tx_done = 1;
Bryan Wu194de562007-05-06 14:50:30 -0700161#else
Roy Huangf4d640c2007-07-12 16:43:46 +0800162#ifdef CONFIG_BF54x
Roy Huangf4d640c2007-07-12 16:43:46 +0800163 /* Clear TFI bit */
164 UART_PUT_LSR(uart, TFI);
Bryan Wu194de562007-05-06 14:50:30 -0700165#endif
Mike Frysinger89bf6dc2008-05-07 11:41:26 +0800166 UART_CLEAR_IER(uart, ETBEI);
Roy Huangf4d640c2007-07-12 16:43:46 +0800167#endif
Bryan Wu194de562007-05-06 14:50:30 -0700168}
169
170/*
171 * port is locked and interrupts are disabled
172 */
173static void bfin_serial_start_tx(struct uart_port *port)
174{
175 struct bfin_serial_port *uart = (struct bfin_serial_port *)port;
Alan Coxebd2c8f2009-09-19 13:13:28 -0700176 struct tty_struct *tty = uart->port.state->port.tty;
Graf Yang80d5c472009-01-02 13:40:22 +0000177
Sonic Zhangd307d362009-04-07 16:52:26 +0100178#ifdef CONFIG_SERIAL_BFIN_HARD_CTSRTS
Roel Kluindaba0282009-04-21 12:24:58 -0700179 if (uart->scts && !(bfin_serial_get_mctrl(&uart->port) & TIOCM_CTS)) {
Sonic Zhangd307d362009-04-07 16:52:26 +0100180 uart->scts = 0;
181 uart_handle_cts_change(&uart->port, uart->scts);
182 }
183#endif
184
Graf Yang80d5c472009-01-02 13:40:22 +0000185 /*
186 * To avoid losting RX interrupt, we reset IR function
187 * before sending data.
188 */
189 if (tty->termios->c_line == N_IRDA)
190 bfin_serial_reset_irda(port);
Bryan Wu194de562007-05-06 14:50:30 -0700191
192#ifdef CONFIG_SERIAL_BFIN_DMA
Sonic Zhang0711d852008-02-25 15:16:50 +0800193 if (uart->tx_done)
194 bfin_serial_dma_tx_chars(uart);
Bryan Wu194de562007-05-06 14:50:30 -0700195#else
Roy Huangf4d640c2007-07-12 16:43:46 +0800196 UART_SET_IER(uart, ETBEI);
Sonic Zhanga359cca2007-10-10 16:47:58 +0800197 bfin_serial_tx_chars(uart);
Roy Huangf4d640c2007-07-12 16:43:46 +0800198#endif
Bryan Wu194de562007-05-06 14:50:30 -0700199}
200
201/*
202 * Interrupts are enabled
203 */
204static void bfin_serial_stop_rx(struct uart_port *port)
205{
206 struct bfin_serial_port *uart = (struct bfin_serial_port *)port;
Sonic Zhang52e15f02009-01-02 13:40:14 +0000207
Roy Huangf4d640c2007-07-12 16:43:46 +0800208 UART_CLEAR_IER(uart, ERBFI);
Bryan Wu194de562007-05-06 14:50:30 -0700209}
210
211/*
212 * Set the modem control timer to fire immediately.
213 */
214static void bfin_serial_enable_ms(struct uart_port *port)
215{
216}
217
Sonic Zhang474f1a62007-06-29 16:35:17 +0800218
Mike Frysinger50e2e152008-04-25 03:03:03 +0800219#if ANOMALY_05000363 && defined(CONFIG_SERIAL_BFIN_PIO)
Mike Frysinger8851c712007-12-24 19:48:04 +0800220# define UART_GET_ANOMALY_THRESHOLD(uart) ((uart)->anomaly_threshold)
221# define UART_SET_ANOMALY_THRESHOLD(uart, v) ((uart)->anomaly_threshold = (v))
222#else
223# define UART_GET_ANOMALY_THRESHOLD(uart) 0
224# define UART_SET_ANOMALY_THRESHOLD(uart, v)
225#endif
226
Bryan Wu194de562007-05-06 14:50:30 -0700227#ifdef CONFIG_SERIAL_BFIN_PIO
Bryan Wu194de562007-05-06 14:50:30 -0700228static void bfin_serial_rx_chars(struct bfin_serial_port *uart)
229{
Sonic Zhang52e15f02009-01-02 13:40:14 +0000230 struct tty_struct *tty = NULL;
Bryan Wu194de562007-05-06 14:50:30 -0700231 unsigned int status, ch, flg;
Mike Frysinger8851c712007-12-24 19:48:04 +0800232 static struct timeval anomaly_start = { .tv_sec = 0 };
Bryan Wu194de562007-05-06 14:50:30 -0700233
Sonic Zhang759eb042007-11-21 17:00:32 +0800234 status = UART_GET_LSR(uart);
Mike Frysinger0bcfd702007-12-24 19:40:05 +0800235 UART_CLEAR_LSR(uart);
236
237 ch = UART_GET_CHAR(uart);
Bryan Wu194de562007-05-06 14:50:30 -0700238 uart->port.icount.rx++;
239
Sonic Zhang52e15f02009-01-02 13:40:14 +0000240#if defined(CONFIG_KGDB_SERIAL_CONSOLE) || \
241 defined(CONFIG_KGDB_SERIAL_CONSOLE_MODULE)
Sonic Zhangcdc592d2010-01-19 06:13:12 -0500242 if (kgdb_connected && kgdboc_port_line == uart->port.line
243 && kgdboc_break_enabled)
Sonic Zhang52e15f02009-01-02 13:40:14 +0000244 if (ch == 0x3) {/* Ctrl + C */
245 kgdb_breakpoint();
Sonic Zhang474f1a62007-06-29 16:35:17 +0800246 return;
Sonic Zhang474f1a62007-06-29 16:35:17 +0800247 }
Sonic Zhang52e15f02009-01-02 13:40:14 +0000248
Alan Coxebd2c8f2009-09-19 13:13:28 -0700249 if (!uart->port.state || !uart->port.state->port.tty)
Sonic Zhang52e15f02009-01-02 13:40:14 +0000250 return;
Sonic Zhang474f1a62007-06-29 16:35:17 +0800251#endif
Alan Coxebd2c8f2009-09-19 13:13:28 -0700252 tty = uart->port.state->port.tty;
Mike Frysingerbbf275f2007-08-05 16:48:08 +0800253
Mike Frysinger50e2e152008-04-25 03:03:03 +0800254 if (ANOMALY_05000363) {
Mike Frysinger8851c712007-12-24 19:48:04 +0800255 /* The BF533 (and BF561) family of processors have a nice anomaly
256 * where they continuously generate characters for a "single" break.
Mike Frysingerbbf275f2007-08-05 16:48:08 +0800257 * We have to basically ignore this flood until the "next" valid
Mike Frysinger8851c712007-12-24 19:48:04 +0800258 * character comes across. Due to the nature of the flood, it is
259 * not possible to reliably catch bytes that are sent too quickly
260 * after this break. So application code talking to the Blackfin
261 * which sends a break signal must allow at least 1.5 character
262 * times after the end of the break for things to stabilize. This
263 * timeout was picked as it must absolutely be larger than 1
264 * character time +/- some percent. So 1.5 sounds good. All other
265 * Blackfin families operate properly. Woo.
Mike Frysingerbbf275f2007-08-05 16:48:08 +0800266 */
Mike Frysinger8851c712007-12-24 19:48:04 +0800267 if (anomaly_start.tv_sec) {
268 struct timeval curr;
269 suseconds_t usecs;
270
271 if ((~ch & (~ch + 1)) & 0xff)
272 goto known_good_char;
273
274 do_gettimeofday(&curr);
275 if (curr.tv_sec - anomaly_start.tv_sec > 1)
276 goto known_good_char;
277
278 usecs = 0;
279 if (curr.tv_sec != anomaly_start.tv_sec)
280 usecs += USEC_PER_SEC;
281 usecs += curr.tv_usec - anomaly_start.tv_usec;
282
283 if (usecs > UART_GET_ANOMALY_THRESHOLD(uart))
284 goto known_good_char;
285
286 if (ch)
287 anomaly_start.tv_sec = 0;
288 else
289 anomaly_start = curr;
290
291 return;
292
293 known_good_char:
Sonic Zhange482a232009-01-02 13:40:45 +0000294 status &= ~BI;
Mike Frysinger8851c712007-12-24 19:48:04 +0800295 anomaly_start.tv_sec = 0;
Mike Frysingerbbf275f2007-08-05 16:48:08 +0800296 }
Bryan Wu194de562007-05-06 14:50:30 -0700297 }
Bryan Wu194de562007-05-06 14:50:30 -0700298
299 if (status & BI) {
Mike Frysinger50e2e152008-04-25 03:03:03 +0800300 if (ANOMALY_05000363)
Mike Frysinger8851c712007-12-24 19:48:04 +0800301 if (bfin_revid() < 5)
302 do_gettimeofday(&anomaly_start);
Bryan Wu194de562007-05-06 14:50:30 -0700303 uart->port.icount.brk++;
304 if (uart_handle_break(&uart->port))
305 goto ignore_char;
Mike Frysinger98089012007-06-11 15:31:30 +0800306 status &= ~(PE | FE);
Mike Frysinger2ac5ee42007-05-21 18:09:39 +0800307 }
308 if (status & PE)
Bryan Wu194de562007-05-06 14:50:30 -0700309 uart->port.icount.parity++;
Mike Frysinger2ac5ee42007-05-21 18:09:39 +0800310 if (status & OE)
Bryan Wu194de562007-05-06 14:50:30 -0700311 uart->port.icount.overrun++;
Mike Frysinger2ac5ee42007-05-21 18:09:39 +0800312 if (status & FE)
Bryan Wu194de562007-05-06 14:50:30 -0700313 uart->port.icount.frame++;
Mike Frysinger2ac5ee42007-05-21 18:09:39 +0800314
315 status &= uart->port.read_status_mask;
316
317 if (status & BI)
318 flg = TTY_BREAK;
319 else if (status & PE)
320 flg = TTY_PARITY;
321 else if (status & FE)
322 flg = TTY_FRAME;
323 else
Bryan Wu194de562007-05-06 14:50:30 -0700324 flg = TTY_NORMAL;
325
326 if (uart_handle_sysrq_char(&uart->port, ch))
327 goto ignore_char;
Bryan Wu194de562007-05-06 14:50:30 -0700328
Mike Frysinger2ac5ee42007-05-21 18:09:39 +0800329 uart_insert_char(&uart->port, status, OE, ch, flg);
330
331 ignore_char:
332 tty_flip_buffer_push(tty);
Bryan Wu194de562007-05-06 14:50:30 -0700333}
334
335static void bfin_serial_tx_chars(struct bfin_serial_port *uart)
336{
Alan Coxebd2c8f2009-09-19 13:13:28 -0700337 struct circ_buf *xmit = &uart->port.state->xmit;
Bryan Wu194de562007-05-06 14:50:30 -0700338
Bryan Wu194de562007-05-06 14:50:30 -0700339 if (uart_circ_empty(xmit) || uart_tx_stopped(&uart->port)) {
Sonic Zhang5ffdeea2008-10-13 10:33:33 +0100340#ifdef CONFIG_BF54x
341 /* Clear TFI bit */
342 UART_PUT_LSR(uart, TFI);
343#endif
Sonic Zhang0efa4f22009-06-11 13:45:07 +0100344 /* Anomaly notes:
345 * 05000215 - we always clear ETBEI within last UART TX
346 * interrupt to end a string. It is always set
347 * when start a new tx.
348 */
Sonic Zhang5ffdeea2008-10-13 10:33:33 +0100349 UART_CLEAR_IER(uart, ETBEI);
Bryan Wu194de562007-05-06 14:50:30 -0700350 return;
351 }
352
Sonic Zhangf30ac0c2008-06-19 17:46:39 +0800353 if (uart->port.x_char) {
354 UART_PUT_CHAR(uart, uart->port.x_char);
355 uart->port.icount.tx++;
356 uart->port.x_char = 0;
357 }
358
Sonic Zhang759eb042007-11-21 17:00:32 +0800359 while ((UART_GET_LSR(uart) & THRE) && xmit->tail != xmit->head) {
360 UART_PUT_CHAR(uart, xmit->buf[xmit->tail]);
361 xmit->tail = (xmit->tail + 1) & (UART_XMIT_SIZE - 1);
362 uart->port.icount.tx++;
Sonic Zhang759eb042007-11-21 17:00:32 +0800363 }
Bryan Wu194de562007-05-06 14:50:30 -0700364
365 if (uart_circ_chars_pending(xmit) < WAKEUP_CHARS)
366 uart_write_wakeup(&uart->port);
Bryan Wu194de562007-05-06 14:50:30 -0700367}
368
Aubrey Li5c4e4722007-05-21 18:09:38 +0800369static irqreturn_t bfin_serial_rx_int(int irq, void *dev_id)
370{
371 struct bfin_serial_port *uart = dev_id;
372
Roy Huangf4d640c2007-07-12 16:43:46 +0800373 spin_lock(&uart->port.lock);
Mike Frysinger0bcfd702007-12-24 19:40:05 +0800374 while (UART_GET_LSR(uart) & DR)
Aubrey Li5c4e4722007-05-21 18:09:38 +0800375 bfin_serial_rx_chars(uart);
376 spin_unlock(&uart->port.lock);
Sonic Zhang759eb042007-11-21 17:00:32 +0800377
Aubrey Li5c4e4722007-05-21 18:09:38 +0800378 return IRQ_HANDLED;
379}
380
381static irqreturn_t bfin_serial_tx_int(int irq, void *dev_id)
Bryan Wu194de562007-05-06 14:50:30 -0700382{
383 struct bfin_serial_port *uart = dev_id;
Bryan Wu194de562007-05-06 14:50:30 -0700384
Sonic Zhangd307d362009-04-07 16:52:26 +0100385#ifdef CONFIG_SERIAL_BFIN_HARD_CTSRTS
Roel Kluindaba0282009-04-21 12:24:58 -0700386 if (uart->scts && !(bfin_serial_get_mctrl(&uart->port) & TIOCM_CTS)) {
Sonic Zhangd307d362009-04-07 16:52:26 +0100387 uart->scts = 0;
388 uart_handle_cts_change(&uart->port, uart->scts);
389 }
390#endif
Roy Huangf4d640c2007-07-12 16:43:46 +0800391 spin_lock(&uart->port.lock);
Mike Frysinger0bcfd702007-12-24 19:40:05 +0800392 if (UART_GET_LSR(uart) & THRE)
Aubrey Li5c4e4722007-05-21 18:09:38 +0800393 bfin_serial_tx_chars(uart);
Bryan Wu194de562007-05-06 14:50:30 -0700394 spin_unlock(&uart->port.lock);
Sonic Zhang759eb042007-11-21 17:00:32 +0800395
Bryan Wu194de562007-05-06 14:50:30 -0700396 return IRQ_HANDLED;
397}
Sonic Zhang4cb4f222008-02-02 14:29:25 +0800398#endif
Bryan Wu194de562007-05-06 14:50:30 -0700399
Bryan Wu194de562007-05-06 14:50:30 -0700400#ifdef CONFIG_SERIAL_BFIN_DMA
401static void bfin_serial_dma_tx_chars(struct bfin_serial_port *uart)
402{
Alan Coxebd2c8f2009-09-19 13:13:28 -0700403 struct circ_buf *xmit = &uart->port.state->xmit;
Bryan Wu194de562007-05-06 14:50:30 -0700404
Bryan Wu194de562007-05-06 14:50:30 -0700405 uart->tx_done = 0;
406
Bryan Wu194de562007-05-06 14:50:30 -0700407 if (uart_circ_empty(xmit) || uart_tx_stopped(&uart->port)) {
Sonic Zhang0711d852008-02-25 15:16:50 +0800408 uart->tx_count = 0;
Bryan Wu194de562007-05-06 14:50:30 -0700409 uart->tx_done = 1;
410 return;
411 }
412
Sonic Zhang1b733512007-12-21 16:45:12 +0800413 if (uart->port.x_char) {
414 UART_PUT_CHAR(uart, uart->port.x_char);
415 uart->port.icount.tx++;
416 uart->port.x_char = 0;
417 }
418
Bryan Wu194de562007-05-06 14:50:30 -0700419 uart->tx_count = CIRC_CNT(xmit->head, xmit->tail, UART_XMIT_SIZE);
420 if (uart->tx_count > (UART_XMIT_SIZE - xmit->tail))
421 uart->tx_count = UART_XMIT_SIZE - xmit->tail;
422 blackfin_dcache_flush_range((unsigned long)(xmit->buf+xmit->tail),
423 (unsigned long)(xmit->buf+xmit->tail+uart->tx_count));
424 set_dma_config(uart->tx_dma_channel,
425 set_bfin_dma_config(DIR_READ, DMA_FLOW_STOP,
426 INTR_ON_BUF,
427 DIMENSION_LINEAR,
Michael Hennerich2047e402008-01-22 15:29:18 +0800428 DATA_SIZE_8,
429 DMA_SYNC_RESTART));
Bryan Wu194de562007-05-06 14:50:30 -0700430 set_dma_start_addr(uart->tx_dma_channel, (unsigned long)(xmit->buf+xmit->tail));
431 set_dma_x_count(uart->tx_dma_channel, uart->tx_count);
432 set_dma_x_modify(uart->tx_dma_channel, 1);
Graf Yangf9d36da2009-06-11 13:42:17 +0100433 SSYNC();
Bryan Wu194de562007-05-06 14:50:30 -0700434 enable_dma(uart->tx_dma_channel);
Sonic Zhang99ee7b52007-12-21 17:12:55 +0800435
Roy Huangf4d640c2007-07-12 16:43:46 +0800436 UART_SET_IER(uart, ETBEI);
Bryan Wu194de562007-05-06 14:50:30 -0700437}
438
Mike Frysinger2ac5ee42007-05-21 18:09:39 +0800439static void bfin_serial_dma_rx_chars(struct bfin_serial_port *uart)
Bryan Wu194de562007-05-06 14:50:30 -0700440{
Alan Coxebd2c8f2009-09-19 13:13:28 -0700441 struct tty_struct *tty = uart->port.state->port.tty;
Bryan Wu194de562007-05-06 14:50:30 -0700442 int i, flg, status;
443
444 status = UART_GET_LSR(uart);
Mike Frysinger0bcfd702007-12-24 19:40:05 +0800445 UART_CLEAR_LSR(uart);
446
Sonic Zhang56f5de82008-02-25 15:19:09 +0800447 uart->port.icount.rx +=
448 CIRC_CNT(uart->rx_dma_buf.head, uart->rx_dma_buf.tail,
449 UART_XMIT_SIZE);
Bryan Wu194de562007-05-06 14:50:30 -0700450
451 if (status & BI) {
452 uart->port.icount.brk++;
453 if (uart_handle_break(&uart->port))
454 goto dma_ignore_char;
Mike Frysinger98089012007-06-11 15:31:30 +0800455 status &= ~(PE | FE);
Mike Frysinger2ac5ee42007-05-21 18:09:39 +0800456 }
457 if (status & PE)
Bryan Wu194de562007-05-06 14:50:30 -0700458 uart->port.icount.parity++;
Mike Frysinger2ac5ee42007-05-21 18:09:39 +0800459 if (status & OE)
Bryan Wu194de562007-05-06 14:50:30 -0700460 uart->port.icount.overrun++;
Mike Frysinger2ac5ee42007-05-21 18:09:39 +0800461 if (status & FE)
Bryan Wu194de562007-05-06 14:50:30 -0700462 uart->port.icount.frame++;
Mike Frysinger2ac5ee42007-05-21 18:09:39 +0800463
464 status &= uart->port.read_status_mask;
465
466 if (status & BI)
467 flg = TTY_BREAK;
468 else if (status & PE)
469 flg = TTY_PARITY;
470 else if (status & FE)
471 flg = TTY_FRAME;
472 else
Bryan Wu194de562007-05-06 14:50:30 -0700473 flg = TTY_NORMAL;
474
Sonic Zhang8c4210e2009-04-06 17:32:42 +0100475 for (i = uart->rx_dma_buf.tail; ; i++) {
Sonic Zhang56f5de82008-02-25 15:19:09 +0800476 if (i >= UART_XMIT_SIZE)
477 i = 0;
Sonic Zhang8c4210e2009-04-06 17:32:42 +0100478 if (i == uart->rx_dma_buf.head)
479 break;
Sonic Zhang56f5de82008-02-25 15:19:09 +0800480 if (!uart_handle_sysrq_char(&uart->port, uart->rx_dma_buf.buf[i]))
481 uart_insert_char(&uart->port, status, OE,
482 uart->rx_dma_buf.buf[i], flg);
Bryan Wu194de562007-05-06 14:50:30 -0700483 }
Mike Frysinger2ac5ee42007-05-21 18:09:39 +0800484
485 dma_ignore_char:
Bryan Wu194de562007-05-06 14:50:30 -0700486 tty_flip_buffer_push(tty);
487}
488
489void bfin_serial_rx_dma_timeout(struct bfin_serial_port *uart)
490{
Mike Frysinger59e4e3e2009-04-06 17:32:28 +0100491 int x_pos, pos;
Sonic Zhang68a784c2009-01-02 13:40:38 +0000492
Graf Yang7ed43f62010-01-19 06:13:11 -0500493 dma_disable_irq(uart->tx_dma_channel);
Sonic Zhang2860b792009-06-11 13:51:33 +0100494 dma_disable_irq(uart->rx_dma_channel);
495 spin_lock_bh(&uart->port.lock);
Bryan Wu194de562007-05-06 14:50:30 -0700496
Sonic Zhang8516c562009-06-11 13:38:16 +0100497 /* 2D DMA RX buffer ring is used. Because curr_y_count and
498 * curr_x_count can't be read as an atomic operation,
499 * curr_y_count should be read before curr_x_count. When
500 * curr_x_count is read, curr_y_count may already indicate
501 * next buffer line. But, the position calculated here is
502 * still indicate the old line. The wrong position data may
503 * be smaller than current buffer tail, which cause garbages
504 * are received if it is not prohibit.
505 */
Sonic Zhang56f5de82008-02-25 15:19:09 +0800506 uart->rx_dma_nrows = get_dma_curr_ycount(uart->rx_dma_channel);
507 x_pos = get_dma_curr_xcount(uart->rx_dma_channel);
508 uart->rx_dma_nrows = DMA_RX_YCOUNT - uart->rx_dma_nrows;
Sonic Zhang35ff6932009-06-11 13:42:57 +0100509 if (uart->rx_dma_nrows == DMA_RX_YCOUNT || x_pos == 0)
Sonic Zhang56f5de82008-02-25 15:19:09 +0800510 uart->rx_dma_nrows = 0;
511 x_pos = DMA_RX_XCOUNT - x_pos;
Bryan Wu194de562007-05-06 14:50:30 -0700512 if (x_pos == DMA_RX_XCOUNT)
513 x_pos = 0;
514
515 pos = uart->rx_dma_nrows * DMA_RX_XCOUNT + x_pos;
Sonic Zhang8516c562009-06-11 13:38:16 +0100516 /* Ignore receiving data if new position is in the same line of
517 * current buffer tail and small.
518 */
519 if (pos > uart->rx_dma_buf.tail ||
520 uart->rx_dma_nrows < (uart->rx_dma_buf.tail/DMA_RX_XCOUNT)) {
Sonic Zhang56f5de82008-02-25 15:19:09 +0800521 uart->rx_dma_buf.head = pos;
Bryan Wu194de562007-05-06 14:50:30 -0700522 bfin_serial_dma_rx_chars(uart);
Sonic Zhang56f5de82008-02-25 15:19:09 +0800523 uart->rx_dma_buf.tail = uart->rx_dma_buf.head;
Bryan Wu194de562007-05-06 14:50:30 -0700524 }
Sonic Zhang0aef4562008-02-29 12:08:42 +0800525
Sonic Zhang2860b792009-06-11 13:51:33 +0100526 spin_unlock_bh(&uart->port.lock);
Graf Yang7ed43f62010-01-19 06:13:11 -0500527 dma_enable_irq(uart->tx_dma_channel);
Sonic Zhang2860b792009-06-11 13:51:33 +0100528 dma_enable_irq(uart->rx_dma_channel);
Sonic Zhang68a784c2009-01-02 13:40:38 +0000529
Sonic Zhang0a278422008-04-25 04:36:47 +0800530 mod_timer(&(uart->rx_dma_timer), jiffies + DMA_RX_FLUSH_JIFFIES);
Bryan Wu194de562007-05-06 14:50:30 -0700531}
532
533static irqreturn_t bfin_serial_dma_tx_int(int irq, void *dev_id)
534{
535 struct bfin_serial_port *uart = dev_id;
Alan Coxebd2c8f2009-09-19 13:13:28 -0700536 struct circ_buf *xmit = &uart->port.state->xmit;
Bryan Wu194de562007-05-06 14:50:30 -0700537
Sonic Zhangd307d362009-04-07 16:52:26 +0100538#ifdef CONFIG_SERIAL_BFIN_HARD_CTSRTS
Roel Kluindaba0282009-04-21 12:24:58 -0700539 if (uart->scts && !(bfin_serial_get_mctrl(&uart->port)&TIOCM_CTS)) {
Sonic Zhangd307d362009-04-07 16:52:26 +0100540 uart->scts = 0;
541 uart_handle_cts_change(&uart->port, uart->scts);
542 }
543#endif
544
Bryan Wu194de562007-05-06 14:50:30 -0700545 spin_lock(&uart->port.lock);
546 if (!(get_dma_curr_irqstat(uart->tx_dma_channel)&DMA_RUN)) {
Bryan Wu194de562007-05-06 14:50:30 -0700547 disable_dma(uart->tx_dma_channel);
Sonic Zhang0711d852008-02-25 15:16:50 +0800548 clear_dma_irqstat(uart->tx_dma_channel);
Sonic Zhang0efa4f22009-06-11 13:45:07 +0100549 /* Anomaly notes:
550 * 05000215 - we always clear ETBEI within last UART TX
551 * interrupt to end a string. It is always set
552 * when start a new tx.
553 */
Roy Huangf4d640c2007-07-12 16:43:46 +0800554 UART_CLEAR_IER(uart, ETBEI);
Sonic Zhang0711d852008-02-25 15:16:50 +0800555 xmit->tail = (xmit->tail + uart->tx_count) & (UART_XMIT_SIZE - 1);
556 uart->port.icount.tx += uart->tx_count;
Sonic Zhang1b733512007-12-21 16:45:12 +0800557
Sonic Zhang56f5de82008-02-25 15:19:09 +0800558 if (uart_circ_chars_pending(xmit) < WAKEUP_CHARS)
559 uart_write_wakeup(&uart->port);
560
Sonic Zhang1b733512007-12-21 16:45:12 +0800561 bfin_serial_dma_tx_chars(uart);
Bryan Wu194de562007-05-06 14:50:30 -0700562 }
563
564 spin_unlock(&uart->port.lock);
565 return IRQ_HANDLED;
566}
567
568static irqreturn_t bfin_serial_dma_rx_int(int irq, void *dev_id)
569{
570 struct bfin_serial_port *uart = dev_id;
571 unsigned short irqstat;
Sonic Zhang35ff6932009-06-11 13:42:57 +0100572 int x_pos, pos;
Sonic Zhang0711d852008-02-25 15:16:50 +0800573
Bryan Wu194de562007-05-06 14:50:30 -0700574 spin_lock(&uart->port.lock);
575 irqstat = get_dma_curr_irqstat(uart->rx_dma_channel);
576 clear_dma_irqstat(uart->rx_dma_channel);
Sonic Zhang8516c562009-06-11 13:38:16 +0100577
578 uart->rx_dma_nrows = get_dma_curr_ycount(uart->rx_dma_channel);
Sonic Zhang35ff6932009-06-11 13:42:57 +0100579 x_pos = get_dma_curr_xcount(uart->rx_dma_channel);
Sonic Zhang8516c562009-06-11 13:38:16 +0100580 uart->rx_dma_nrows = DMA_RX_YCOUNT - uart->rx_dma_nrows;
Sonic Zhang35ff6932009-06-11 13:42:57 +0100581 if (uart->rx_dma_nrows == DMA_RX_YCOUNT || x_pos == 0)
Sonic Zhang8516c562009-06-11 13:38:16 +0100582 uart->rx_dma_nrows = 0;
583
584 pos = uart->rx_dma_nrows * DMA_RX_XCOUNT;
585 if (pos > uart->rx_dma_buf.tail ||
586 uart->rx_dma_nrows < (uart->rx_dma_buf.tail/DMA_RX_XCOUNT)) {
587 uart->rx_dma_buf.head = pos;
588 bfin_serial_dma_rx_chars(uart);
589 uart->rx_dma_buf.tail = uart->rx_dma_buf.head;
590 }
591
Bryan Wu194de562007-05-06 14:50:30 -0700592 spin_unlock(&uart->port.lock);
Sonic Zhang0aef4562008-02-29 12:08:42 +0800593
Bryan Wu194de562007-05-06 14:50:30 -0700594 return IRQ_HANDLED;
595}
596#endif
597
598/*
599 * Return TIOCSER_TEMT when transmitter is not busy.
600 */
601static unsigned int bfin_serial_tx_empty(struct uart_port *port)
602{
603 struct bfin_serial_port *uart = (struct bfin_serial_port *)port;
604 unsigned short lsr;
605
606 lsr = UART_GET_LSR(uart);
607 if (lsr & TEMT)
608 return TIOCSER_TEMT;
609 else
610 return 0;
611}
612
Bryan Wu194de562007-05-06 14:50:30 -0700613static void bfin_serial_break_ctl(struct uart_port *port, int break_state)
614{
Mike Frysingercf686762007-06-11 16:12:49 +0800615 struct bfin_serial_port *uart = (struct bfin_serial_port *)port;
616 u16 lcr = UART_GET_LCR(uart);
617 if (break_state)
618 lcr |= SB;
619 else
620 lcr &= ~SB;
621 UART_PUT_LCR(uart, lcr);
622 SSYNC();
Bryan Wu194de562007-05-06 14:50:30 -0700623}
624
625static int bfin_serial_startup(struct uart_port *port)
626{
627 struct bfin_serial_port *uart = (struct bfin_serial_port *)port;
628
629#ifdef CONFIG_SERIAL_BFIN_DMA
630 dma_addr_t dma_handle;
631
632 if (request_dma(uart->rx_dma_channel, "BFIN_UART_RX") < 0) {
633 printk(KERN_NOTICE "Unable to attach Blackfin UART RX DMA channel\n");
634 return -EBUSY;
635 }
636
637 if (request_dma(uart->tx_dma_channel, "BFIN_UART_TX") < 0) {
638 printk(KERN_NOTICE "Unable to attach Blackfin UART TX DMA channel\n");
639 free_dma(uart->rx_dma_channel);
640 return -EBUSY;
641 }
642
643 set_dma_callback(uart->rx_dma_channel, bfin_serial_dma_rx_int, uart);
644 set_dma_callback(uart->tx_dma_channel, bfin_serial_dma_tx_int, uart);
645
646 uart->rx_dma_buf.buf = (unsigned char *)dma_alloc_coherent(NULL, PAGE_SIZE, &dma_handle, GFP_DMA);
647 uart->rx_dma_buf.head = 0;
648 uart->rx_dma_buf.tail = 0;
649 uart->rx_dma_nrows = 0;
650
651 set_dma_config(uart->rx_dma_channel,
652 set_bfin_dma_config(DIR_WRITE, DMA_FLOW_AUTO,
653 INTR_ON_ROW, DIMENSION_2D,
Michael Hennerich2047e402008-01-22 15:29:18 +0800654 DATA_SIZE_8,
655 DMA_SYNC_RESTART));
Bryan Wu194de562007-05-06 14:50:30 -0700656 set_dma_x_count(uart->rx_dma_channel, DMA_RX_XCOUNT);
657 set_dma_x_modify(uart->rx_dma_channel, 1);
658 set_dma_y_count(uart->rx_dma_channel, DMA_RX_YCOUNT);
659 set_dma_y_modify(uart->rx_dma_channel, 1);
660 set_dma_start_addr(uart->rx_dma_channel, (unsigned long)uart->rx_dma_buf.buf);
661 enable_dma(uart->rx_dma_channel);
662
663 uart->rx_dma_timer.data = (unsigned long)(uart);
664 uart->rx_dma_timer.function = (void *)bfin_serial_rx_dma_timeout;
665 uart->rx_dma_timer.expires = jiffies + DMA_RX_FLUSH_JIFFIES;
666 add_timer(&(uart->rx_dma_timer));
667#else
Sonic Zhang6f955702009-04-07 16:51:15 +0100668# if defined(CONFIG_KGDB_SERIAL_CONSOLE) || \
Sonic Zhang52e15f02009-01-02 13:40:14 +0000669 defined(CONFIG_KGDB_SERIAL_CONSOLE_MODULE)
670 if (kgdboc_port_line == uart->port.line && kgdboc_break_enabled)
671 kgdboc_break_enabled = 0;
672 else {
673# endif
Sonic Zhanga359cca2007-10-10 16:47:58 +0800674 if (request_irq(uart->port.irq, bfin_serial_rx_int, IRQF_DISABLED,
Bryan Wu194de562007-05-06 14:50:30 -0700675 "BFIN_UART_RX", uart)) {
676 printk(KERN_NOTICE "Unable to attach BlackFin UART RX interrupt\n");
677 return -EBUSY;
678 }
679
680 if (request_irq
Aubrey Li5c4e4722007-05-21 18:09:38 +0800681 (uart->port.irq+1, bfin_serial_tx_int, IRQF_DISABLED,
Bryan Wu194de562007-05-06 14:50:30 -0700682 "BFIN_UART_TX", uart)) {
683 printk(KERN_NOTICE "Unable to attach BlackFin UART TX interrupt\n");
684 free_irq(uart->port.irq, uart);
685 return -EBUSY;
686 }
Sonic Zhangab2375f2008-10-13 10:33:51 +0100687
688# ifdef CONFIG_BF54x
689 {
Sonic Zhangb6100992010-10-27 04:16:47 -0400690 /*
691 * UART2 and UART3 on BF548 share interrupt PINs and DMA
692 * controllers with SPORT2 and SPORT3. UART rx and tx
693 * interrupts are generated in PIO mode only when configure
694 * their peripheral mapping registers properly, which means
695 * request corresponding DMA channels in PIO mode as well.
696 */
Sonic Zhangab2375f2008-10-13 10:33:51 +0100697 unsigned uart_dma_ch_rx, uart_dma_ch_tx;
698
699 switch (uart->port.irq) {
700 case IRQ_UART3_RX:
701 uart_dma_ch_rx = CH_UART3_RX;
702 uart_dma_ch_tx = CH_UART3_TX;
703 break;
704 case IRQ_UART2_RX:
705 uart_dma_ch_rx = CH_UART2_RX;
706 uart_dma_ch_tx = CH_UART2_TX;
707 break;
708 default:
709 uart_dma_ch_rx = uart_dma_ch_tx = 0;
710 break;
711 };
712
713 if (uart_dma_ch_rx &&
714 request_dma(uart_dma_ch_rx, "BFIN_UART_RX") < 0) {
715 printk(KERN_NOTICE"Fail to attach UART interrupt\n");
716 free_irq(uart->port.irq, uart);
717 free_irq(uart->port.irq + 1, uart);
718 return -EBUSY;
719 }
720 if (uart_dma_ch_tx &&
721 request_dma(uart_dma_ch_tx, "BFIN_UART_TX") < 0) {
722 printk(KERN_NOTICE "Fail to attach UART interrupt\n");
723 free_dma(uart_dma_ch_rx);
724 free_irq(uart->port.irq, uart);
725 free_irq(uart->port.irq + 1, uart);
726 return -EBUSY;
727 }
728 }
729# endif
Sonic Zhang6f955702009-04-07 16:51:15 +0100730# if defined(CONFIG_KGDB_SERIAL_CONSOLE) || \
Sonic Zhang52e15f02009-01-02 13:40:14 +0000731 defined(CONFIG_KGDB_SERIAL_CONSOLE_MODULE)
732 }
733# endif
Bryan Wu194de562007-05-06 14:50:30 -0700734#endif
Sonic Zhang6f955702009-04-07 16:51:15 +0100735
736#ifdef CONFIG_SERIAL_BFIN_CTSRTS
737 if (uart->cts_pin >= 0) {
738 if (request_irq(gpio_to_irq(uart->cts_pin),
739 bfin_serial_mctrl_cts_int,
740 IRQF_TRIGGER_RISING | IRQF_TRIGGER_FALLING |
741 IRQF_DISABLED, "BFIN_UART_CTS", uart)) {
742 uart->cts_pin = -1;
Joe Perchesa89f2462010-11-07 13:10:23 -0800743 pr_info("Unable to attach BlackFin UART CTS interrupt. So, disable it.\n");
Sonic Zhang6f955702009-04-07 16:51:15 +0100744 }
745 }
746 if (uart->rts_pin >= 0) {
Sonic Zhang6f955702009-04-07 16:51:15 +0100747 gpio_direction_output(uart->rts_pin, 0);
748 }
749#endif
Sonic Zhangd307d362009-04-07 16:52:26 +0100750#ifdef CONFIG_SERIAL_BFIN_HARD_CTSRTS
Sonic Zhang57afb392009-09-09 10:46:19 +0000751 if (uart->cts_pin >= 0 && request_irq(uart->status_irq,
Sonic Zhangd307d362009-04-07 16:52:26 +0100752 bfin_serial_mctrl_cts_int,
753 IRQF_DISABLED, "BFIN_UART_MODEM_STATUS", uart)) {
Sonic Zhang57afb392009-09-09 10:46:19 +0000754 uart->cts_pin = -1;
Joe Perchesa89f2462010-11-07 13:10:23 -0800755 pr_info("Unable to attach BlackFin UART Modem Status interrupt.\n");
Sonic Zhangd307d362009-04-07 16:52:26 +0100756 }
757
Sonic Zhangd307d362009-04-07 16:52:26 +0100758 /* CTS RTS PINs are negative assertive. */
759 UART_PUT_MCR(uart, ACTS);
760 UART_SET_IER(uart, EDSSI);
761#endif
762
Roy Huangf4d640c2007-07-12 16:43:46 +0800763 UART_SET_IER(uart, ERBFI);
Bryan Wu194de562007-05-06 14:50:30 -0700764 return 0;
765}
766
767static void bfin_serial_shutdown(struct uart_port *port)
768{
769 struct bfin_serial_port *uart = (struct bfin_serial_port *)port;
770
771#ifdef CONFIG_SERIAL_BFIN_DMA
772 disable_dma(uart->tx_dma_channel);
773 free_dma(uart->tx_dma_channel);
774 disable_dma(uart->rx_dma_channel);
775 free_dma(uart->rx_dma_channel);
776 del_timer(&(uart->rx_dma_timer));
Sonic Zhang75b780b2007-12-21 17:03:39 +0800777 dma_free_coherent(NULL, PAGE_SIZE, uart->rx_dma_buf.buf, 0);
Bryan Wu194de562007-05-06 14:50:30 -0700778#else
Sonic Zhangab2375f2008-10-13 10:33:51 +0100779#ifdef CONFIG_BF54x
780 switch (uart->port.irq) {
781 case IRQ_UART3_RX:
782 free_dma(CH_UART3_RX);
783 free_dma(CH_UART3_TX);
784 break;
785 case IRQ_UART2_RX:
786 free_dma(CH_UART2_RX);
787 free_dma(CH_UART2_TX);
788 break;
789 default:
790 break;
791 };
792#endif
Bryan Wu194de562007-05-06 14:50:30 -0700793 free_irq(uart->port.irq, uart);
794 free_irq(uart->port.irq+1, uart);
795#endif
Sonic Zhang6f955702009-04-07 16:51:15 +0100796
Sonic Zhangd307d362009-04-07 16:52:26 +0100797#ifdef CONFIG_SERIAL_BFIN_CTSRTS
Sonic Zhang6f955702009-04-07 16:51:15 +0100798 if (uart->cts_pin >= 0)
799 free_irq(gpio_to_irq(uart->cts_pin), uart);
Sonic Zhangd307d362009-04-07 16:52:26 +0100800#endif
801#ifdef CONFIG_SERIAL_BFIN_HARD_CTSRTS
Sonic Zhang57afb392009-09-09 10:46:19 +0000802 if (uart->cts_pin >= 0)
Sonic Zhangd307d362009-04-07 16:52:26 +0100803 free_irq(uart->status_irq, uart);
804#endif
Bryan Wu194de562007-05-06 14:50:30 -0700805}
806
807static void
808bfin_serial_set_termios(struct uart_port *port, struct ktermios *termios,
809 struct ktermios *old)
810{
811 struct bfin_serial_port *uart = (struct bfin_serial_port *)port;
812 unsigned long flags;
813 unsigned int baud, quot;
Mike Frysinger0c44a862008-04-24 04:56:02 +0800814 unsigned short val, ier, lcr = 0;
Bryan Wu194de562007-05-06 14:50:30 -0700815
816 switch (termios->c_cflag & CSIZE) {
817 case CS8:
818 lcr = WLS(8);
819 break;
820 case CS7:
821 lcr = WLS(7);
822 break;
823 case CS6:
824 lcr = WLS(6);
825 break;
826 case CS5:
827 lcr = WLS(5);
828 break;
829 default:
830 printk(KERN_ERR "%s: word lengh not supported\n",
Harvey Harrison71cc2c22008-04-30 00:55:10 -0700831 __func__);
Bryan Wu194de562007-05-06 14:50:30 -0700832 }
833
Sonic Zhang84507792009-06-11 13:50:20 +0100834 /* Anomaly notes:
835 * 05000231 - STOP bit is always set to 1 whatever the user is set.
836 */
837 if (termios->c_cflag & CSTOPB) {
838 if (ANOMALY_05000231)
839 printk(KERN_WARNING "STOP bits other than 1 is not "
840 "supported in case of anomaly 05000231.\n");
841 else
842 lcr |= STB;
843 }
Mike Frysinger19aa6382007-06-11 16:16:45 +0800844 if (termios->c_cflag & PARENB)
Bryan Wu194de562007-05-06 14:50:30 -0700845 lcr |= PEN;
Mike Frysinger19aa6382007-06-11 16:16:45 +0800846 if (!(termios->c_cflag & PARODD))
847 lcr |= EPS;
848 if (termios->c_cflag & CMSPAR)
849 lcr |= STP;
Bryan Wu194de562007-05-06 14:50:30 -0700850
Sonic Zhang5bb06b62010-10-27 04:16:50 -0400851 spin_lock_irqsave(&uart->port.lock, flags);
852
Mike Frysinger2ac5ee42007-05-21 18:09:39 +0800853 port->read_status_mask = OE;
854 if (termios->c_iflag & INPCK)
855 port->read_status_mask |= (FE | PE);
856 if (termios->c_iflag & (BRKINT | PARMRK))
857 port->read_status_mask |= BI;
Bryan Wu194de562007-05-06 14:50:30 -0700858
Mike Frysinger2ac5ee42007-05-21 18:09:39 +0800859 /*
860 * Characters to ignore
861 */
862 port->ignore_status_mask = 0;
863 if (termios->c_iflag & IGNPAR)
864 port->ignore_status_mask |= FE | PE;
865 if (termios->c_iflag & IGNBRK) {
866 port->ignore_status_mask |= BI;
867 /*
868 * If we're ignoring parity and break indicators,
869 * ignore overruns too (for real raw support).
870 */
871 if (termios->c_iflag & IGNPAR)
872 port->ignore_status_mask |= OE;
873 }
Bryan Wu194de562007-05-06 14:50:30 -0700874
875 baud = uart_get_baud_rate(port, termios, old, 0, port->uartclk/16);
Graf Yangca3e4422010-05-23 04:40:13 -0400876 quot = uart_get_divisor(port, baud);
877
878 /* If discipline is not IRDA, apply ANOMALY_05000230 */
879 if (termios->c_line != N_IRDA)
880 quot -= ANOMALY_05000230;
881
Mike Frysinger8851c712007-12-24 19:48:04 +0800882 UART_SET_ANOMALY_THRESHOLD(uart, USEC_PER_SEC / baud * 15);
883
Bryan Wu194de562007-05-06 14:50:30 -0700884 /* Disable UART */
885 ier = UART_GET_IER(uart);
Sonic Zhang1feaa512008-06-03 12:19:45 +0800886 UART_DISABLE_INTS(uart);
Bryan Wu194de562007-05-06 14:50:30 -0700887
888 /* Set DLAB in LCR to Access DLL and DLH */
Mike Frysinger45828b82008-05-07 11:41:26 +0800889 UART_SET_DLAB(uart);
Bryan Wu194de562007-05-06 14:50:30 -0700890
891 UART_PUT_DLL(uart, quot & 0xFF);
Bryan Wu194de562007-05-06 14:50:30 -0700892 UART_PUT_DLH(uart, (quot >> 8) & 0xFF);
893 SSYNC();
894
895 /* Clear DLAB in LCR to Access THR RBR IER */
Mike Frysinger45828b82008-05-07 11:41:26 +0800896 UART_CLEAR_DLAB(uart);
Bryan Wu194de562007-05-06 14:50:30 -0700897
898 UART_PUT_LCR(uart, lcr);
899
900 /* Enable UART */
Sonic Zhang1feaa512008-06-03 12:19:45 +0800901 UART_ENABLE_INTS(uart, ier);
Bryan Wu194de562007-05-06 14:50:30 -0700902
903 val = UART_GET_GCTL(uart);
904 val |= UCEN;
905 UART_PUT_GCTL(uart, val);
906
Graf Yangb3ef5ab2008-10-13 10:33:42 +0100907 /* Port speed changed, update the per-port timeout. */
908 uart_update_timeout(port, termios->c_cflag, baud);
909
Bryan Wu194de562007-05-06 14:50:30 -0700910 spin_unlock_irqrestore(&uart->port.lock, flags);
911}
912
913static const char *bfin_serial_type(struct uart_port *port)
914{
915 struct bfin_serial_port *uart = (struct bfin_serial_port *)port;
916
917 return uart->port.type == PORT_BFIN ? "BFIN-UART" : NULL;
918}
919
920/*
921 * Release the memory region(s) being used by 'port'.
922 */
923static void bfin_serial_release_port(struct uart_port *port)
924{
925}
926
927/*
928 * Request the memory region(s) being used by 'port'.
929 */
930static int bfin_serial_request_port(struct uart_port *port)
931{
932 return 0;
933}
934
935/*
936 * Configure/autoconfigure the port.
937 */
938static void bfin_serial_config_port(struct uart_port *port, int flags)
939{
940 struct bfin_serial_port *uart = (struct bfin_serial_port *)port;
941
942 if (flags & UART_CONFIG_TYPE &&
943 bfin_serial_request_port(&uart->port) == 0)
944 uart->port.type = PORT_BFIN;
945}
946
947/*
948 * Verify the new serial_struct (for TIOCSSERIAL).
949 * The only change we allow are to the flags and type, and
950 * even then only between PORT_BFIN and PORT_UNKNOWN
951 */
952static int
953bfin_serial_verify_port(struct uart_port *port, struct serial_struct *ser)
954{
955 return 0;
956}
957
Graf Yang7d01b472008-02-29 11:31:08 +0800958/*
959 * Enable the IrDA function if tty->ldisc.num is N_IRDA.
960 * In other cases, disable IrDA function.
961 */
Alan Coxd87d9b72010-06-01 22:52:53 +0200962static void bfin_serial_set_ldisc(struct uart_port *port, int ld)
Graf Yang7d01b472008-02-29 11:31:08 +0800963{
Sonic Zhang57afb392009-09-09 10:46:19 +0000964 struct bfin_serial_port *uart = (struct bfin_serial_port *)port;
Graf Yang7d01b472008-02-29 11:31:08 +0800965 unsigned short val;
966
Alan Coxd87d9b72010-06-01 22:52:53 +0200967 switch (ld) {
Graf Yang7d01b472008-02-29 11:31:08 +0800968 case N_IRDA:
Sonic Zhang57afb392009-09-09 10:46:19 +0000969 val = UART_GET_GCTL(uart);
Graf Yang7d01b472008-02-29 11:31:08 +0800970 val |= (IREN | RPOLC);
Sonic Zhang57afb392009-09-09 10:46:19 +0000971 UART_PUT_GCTL(uart, val);
Graf Yang7d01b472008-02-29 11:31:08 +0800972 break;
973 default:
Sonic Zhang57afb392009-09-09 10:46:19 +0000974 val = UART_GET_GCTL(uart);
Graf Yang7d01b472008-02-29 11:31:08 +0800975 val &= ~(IREN | RPOLC);
Sonic Zhang57afb392009-09-09 10:46:19 +0000976 UART_PUT_GCTL(uart, val);
Graf Yang7d01b472008-02-29 11:31:08 +0800977 }
978}
979
Sonic Zhang6f955702009-04-07 16:51:15 +0100980static void bfin_serial_reset_irda(struct uart_port *port)
981{
Sonic Zhang57afb392009-09-09 10:46:19 +0000982 struct bfin_serial_port *uart = (struct bfin_serial_port *)port;
Sonic Zhang6f955702009-04-07 16:51:15 +0100983 unsigned short val;
984
Sonic Zhang57afb392009-09-09 10:46:19 +0000985 val = UART_GET_GCTL(uart);
Sonic Zhang6f955702009-04-07 16:51:15 +0100986 val &= ~(IREN | RPOLC);
Sonic Zhang57afb392009-09-09 10:46:19 +0000987 UART_PUT_GCTL(uart, val);
Sonic Zhang6f955702009-04-07 16:51:15 +0100988 SSYNC();
989 val |= (IREN | RPOLC);
Sonic Zhang57afb392009-09-09 10:46:19 +0000990 UART_PUT_GCTL(uart, val);
Sonic Zhang6f955702009-04-07 16:51:15 +0100991 SSYNC();
992}
993
Sonic Zhang52e15f02009-01-02 13:40:14 +0000994#ifdef CONFIG_CONSOLE_POLL
Sonic Zhang0efa4f22009-06-11 13:45:07 +0100995/* Anomaly notes:
996 * 05000099 - Because we only use THRE in poll_put and DR in poll_get,
997 * losing other bits of UART_LSR is not a problem here.
998 */
Sonic Zhang52e15f02009-01-02 13:40:14 +0000999static void bfin_serial_poll_put_char(struct uart_port *port, unsigned char chr)
1000{
1001 struct bfin_serial_port *uart = (struct bfin_serial_port *)port;
1002
1003 while (!(UART_GET_LSR(uart) & THRE))
1004 cpu_relax();
1005
1006 UART_CLEAR_DLAB(uart);
1007 UART_PUT_CHAR(uart, (unsigned char)chr);
1008}
1009
1010static int bfin_serial_poll_get_char(struct uart_port *port)
1011{
1012 struct bfin_serial_port *uart = (struct bfin_serial_port *)port;
1013 unsigned char chr;
1014
1015 while (!(UART_GET_LSR(uart) & DR))
1016 cpu_relax();
1017
1018 UART_CLEAR_DLAB(uart);
1019 chr = UART_GET_CHAR(uart);
1020
1021 return chr;
1022}
1023#endif
1024
1025#if defined(CONFIG_KGDB_SERIAL_CONSOLE) || \
1026 defined(CONFIG_KGDB_SERIAL_CONSOLE_MODULE)
1027static void bfin_kgdboc_port_shutdown(struct uart_port *port)
1028{
1029 if (kgdboc_break_enabled) {
1030 kgdboc_break_enabled = 0;
1031 bfin_serial_shutdown(port);
1032 }
1033}
1034
1035static int bfin_kgdboc_port_startup(struct uart_port *port)
1036{
1037 kgdboc_port_line = port->line;
1038 kgdboc_break_enabled = !bfin_serial_startup(port);
1039 return 0;
1040}
1041#endif
1042
Bryan Wu194de562007-05-06 14:50:30 -07001043static struct uart_ops bfin_serial_pops = {
1044 .tx_empty = bfin_serial_tx_empty,
1045 .set_mctrl = bfin_serial_set_mctrl,
1046 .get_mctrl = bfin_serial_get_mctrl,
1047 .stop_tx = bfin_serial_stop_tx,
1048 .start_tx = bfin_serial_start_tx,
1049 .stop_rx = bfin_serial_stop_rx,
1050 .enable_ms = bfin_serial_enable_ms,
1051 .break_ctl = bfin_serial_break_ctl,
1052 .startup = bfin_serial_startup,
1053 .shutdown = bfin_serial_shutdown,
1054 .set_termios = bfin_serial_set_termios,
Graf Yang3b8458a2008-06-07 15:36:33 +08001055 .set_ldisc = bfin_serial_set_ldisc,
Bryan Wu194de562007-05-06 14:50:30 -07001056 .type = bfin_serial_type,
1057 .release_port = bfin_serial_release_port,
1058 .request_port = bfin_serial_request_port,
1059 .config_port = bfin_serial_config_port,
1060 .verify_port = bfin_serial_verify_port,
Sonic Zhang52e15f02009-01-02 13:40:14 +00001061#if defined(CONFIG_KGDB_SERIAL_CONSOLE) || \
1062 defined(CONFIG_KGDB_SERIAL_CONSOLE_MODULE)
1063 .kgdboc_port_startup = bfin_kgdboc_port_startup,
1064 .kgdboc_port_shutdown = bfin_kgdboc_port_shutdown,
1065#endif
1066#ifdef CONFIG_CONSOLE_POLL
1067 .poll_put_char = bfin_serial_poll_put_char,
1068 .poll_get_char = bfin_serial_poll_get_char,
1069#endif
Bryan Wu194de562007-05-06 14:50:30 -07001070};
1071
Sonic Zhangb6efa1e2009-01-02 13:40:31 +00001072#if defined(CONFIG_SERIAL_BFIN_CONSOLE) || defined(CONFIG_EARLY_PRINTK)
Bryan Wu194de562007-05-06 14:50:30 -07001073/*
1074 * If the port was already initialised (eg, by a boot loader),
1075 * try to determine the current setup.
1076 */
1077static void __init
1078bfin_serial_console_get_options(struct bfin_serial_port *uart, int *baud,
1079 int *parity, int *bits)
1080{
1081 unsigned short status;
1082
1083 status = UART_GET_IER(uart) & (ERBFI | ETBEI);
1084 if (status == (ERBFI | ETBEI)) {
1085 /* ok, the port was enabled */
Mike Frysinger45828b82008-05-07 11:41:26 +08001086 u16 lcr, dlh, dll;
Bryan Wu194de562007-05-06 14:50:30 -07001087
1088 lcr = UART_GET_LCR(uart);
1089
1090 *parity = 'n';
1091 if (lcr & PEN) {
1092 if (lcr & EPS)
1093 *parity = 'e';
1094 else
1095 *parity = 'o';
1096 }
1097 switch (lcr & 0x03) {
1098 case 0: *bits = 5; break;
1099 case 1: *bits = 6; break;
1100 case 2: *bits = 7; break;
1101 case 3: *bits = 8; break;
1102 }
1103 /* Set DLAB in LCR to Access DLL and DLH */
Mike Frysinger45828b82008-05-07 11:41:26 +08001104 UART_SET_DLAB(uart);
Bryan Wu194de562007-05-06 14:50:30 -07001105
1106 dll = UART_GET_DLL(uart);
1107 dlh = UART_GET_DLH(uart);
1108
1109 /* Clear DLAB in LCR to Access THR RBR IER */
Mike Frysinger45828b82008-05-07 11:41:26 +08001110 UART_CLEAR_DLAB(uart);
Bryan Wu194de562007-05-06 14:50:30 -07001111
1112 *baud = get_sclk() / (16*(dll | dlh << 8));
1113 }
Harvey Harrison71cc2c22008-04-30 00:55:10 -07001114 pr_debug("%s:baud = %d, parity = %c, bits= %d\n", __func__, *baud, *parity, *bits);
Bryan Wu194de562007-05-06 14:50:30 -07001115}
Robin Getz0ae53642007-10-09 17:24:49 +08001116
Robin Getz0ae53642007-10-09 17:24:49 +08001117static struct uart_driver bfin_serial_reg;
Bryan Wu194de562007-05-06 14:50:30 -07001118
Sonic Zhang57afb392009-09-09 10:46:19 +00001119static void bfin_serial_console_putchar(struct uart_port *port, int ch)
1120{
1121 struct bfin_serial_port *uart = (struct bfin_serial_port *)port;
1122 while (!(UART_GET_LSR(uart) & THRE))
1123 barrier();
1124 UART_PUT_CHAR(uart, ch);
1125}
1126
1127#endif /* defined (CONFIG_SERIAL_BFIN_CONSOLE) ||
1128 defined (CONFIG_EARLY_PRINTK) */
1129
1130#ifdef CONFIG_SERIAL_BFIN_CONSOLE
1131#define CLASS_BFIN_CONSOLE "bfin-console"
1132/*
1133 * Interrupts are disabled on entering
1134 */
1135static void
1136bfin_serial_console_write(struct console *co, const char *s, unsigned int count)
1137{
1138 struct bfin_serial_port *uart = bfin_serial_ports[co->index];
1139 unsigned long flags;
1140
1141 spin_lock_irqsave(&uart->port.lock, flags);
1142 uart_console_write(&uart->port, s, count, bfin_serial_console_putchar);
1143 spin_unlock_irqrestore(&uart->port.lock, flags);
1144
1145}
1146
Bryan Wu194de562007-05-06 14:50:30 -07001147static int __init
1148bfin_serial_console_setup(struct console *co, char *options)
1149{
1150 struct bfin_serial_port *uart;
1151 int baud = 57600;
1152 int bits = 8;
1153 int parity = 'n';
Sonic Zhangd307d362009-04-07 16:52:26 +01001154# if defined(CONFIG_SERIAL_BFIN_CTSRTS) || \
1155 defined(CONFIG_SERIAL_BFIN_HARD_CTSRTS)
Bryan Wu194de562007-05-06 14:50:30 -07001156 int flow = 'r';
Sonic Zhangb6efa1e2009-01-02 13:40:31 +00001157# else
Bryan Wu194de562007-05-06 14:50:30 -07001158 int flow = 'n';
Robin Getz0ae53642007-10-09 17:24:49 +08001159# endif
Bryan Wu194de562007-05-06 14:50:30 -07001160
1161 /*
1162 * Check whether an invalid uart number has been specified, and
1163 * if so, search for the first available port that does have
1164 * console support.
1165 */
Sonic Zhang57afb392009-09-09 10:46:19 +00001166 if (co->index < 0 || co->index >= BFIN_UART_NR_PORTS)
1167 return -ENODEV;
1168
1169 uart = bfin_serial_ports[co->index];
1170 if (!uart)
1171 return -ENODEV;
Bryan Wu194de562007-05-06 14:50:30 -07001172
1173 if (options)
1174 uart_parse_options(options, &baud, &parity, &bits, &flow);
1175 else
1176 bfin_serial_console_get_options(uart, &baud, &parity, &bits);
1177
1178 return uart_set_options(&uart->port, co, baud, parity, bits, flow);
Robin Getz0ae53642007-10-09 17:24:49 +08001179}
Robin Getz0ae53642007-10-09 17:24:49 +08001180
Bryan Wu194de562007-05-06 14:50:30 -07001181static struct console bfin_serial_console = {
Sonic Zhang57afb392009-09-09 10:46:19 +00001182 .name = BFIN_SERIAL_DEV_NAME,
Bryan Wu194de562007-05-06 14:50:30 -07001183 .write = bfin_serial_console_write,
1184 .device = uart_console_device,
1185 .setup = bfin_serial_console_setup,
1186 .flags = CON_PRINTBUFFER,
1187 .index = -1,
1188 .data = &bfin_serial_reg,
1189};
Bryan Wu194de562007-05-06 14:50:30 -07001190#define BFIN_SERIAL_CONSOLE &bfin_serial_console
1191#else
1192#define BFIN_SERIAL_CONSOLE NULL
Robin Getz0ae53642007-10-09 17:24:49 +08001193#endif /* CONFIG_SERIAL_BFIN_CONSOLE */
1194
Sonic Zhang57afb392009-09-09 10:46:19 +00001195#ifdef CONFIG_EARLY_PRINTK
1196static struct bfin_serial_port bfin_earlyprintk_port;
1197#define CLASS_BFIN_EARLYPRINTK "bfin-earlyprintk"
Robin Getz0ae53642007-10-09 17:24:49 +08001198
Sonic Zhang57afb392009-09-09 10:46:19 +00001199/*
1200 * Interrupts are disabled on entering
1201 */
1202static void
1203bfin_earlyprintk_console_write(struct console *co, const char *s, unsigned int count)
Robin Getz0ae53642007-10-09 17:24:49 +08001204{
Sonic Zhang57afb392009-09-09 10:46:19 +00001205 unsigned long flags;
Robin Getz0ae53642007-10-09 17:24:49 +08001206
Sonic Zhang57afb392009-09-09 10:46:19 +00001207 if (bfin_earlyprintk_port.port.line != co->index)
1208 return;
Robin Getz0ae53642007-10-09 17:24:49 +08001209
Sonic Zhang57afb392009-09-09 10:46:19 +00001210 spin_lock_irqsave(&bfin_earlyprintk_port.port.lock, flags);
1211 uart_console_write(&bfin_earlyprintk_port.port, s, count,
1212 bfin_serial_console_putchar);
1213 spin_unlock_irqrestore(&bfin_earlyprintk_port.port.lock, flags);
Robin Getz0ae53642007-10-09 17:24:49 +08001214}
1215
Robin Getz7de7c552009-06-11 13:38:57 +01001216/*
1217 * This should have a .setup or .early_setup in it, but then things get called
1218 * without the command line options, and the baud rate gets messed up - so
1219 * don't let the common infrastructure play with things. (see calls to setup
1220 * & earlysetup in ./kernel/printk.c:register_console()
1221 */
Mike Frysingerc1113402008-10-13 10:32:35 +01001222static struct __initdata console bfin_early_serial_console = {
Robin Getz0ae53642007-10-09 17:24:49 +08001223 .name = "early_BFuart",
Sonic Zhang57afb392009-09-09 10:46:19 +00001224 .write = bfin_earlyprintk_console_write,
Robin Getz0ae53642007-10-09 17:24:49 +08001225 .device = uart_console_device,
1226 .flags = CON_PRINTBUFFER,
Robin Getz0ae53642007-10-09 17:24:49 +08001227 .index = -1,
1228 .data = &bfin_serial_reg,
1229};
Sonic Zhang57afb392009-09-09 10:46:19 +00001230#endif
1231
1232static struct uart_driver bfin_serial_reg = {
1233 .owner = THIS_MODULE,
1234 .driver_name = DRIVER_NAME,
1235 .dev_name = BFIN_SERIAL_DEV_NAME,
1236 .major = BFIN_SERIAL_MAJOR,
1237 .minor = BFIN_SERIAL_MINOR,
1238 .nr = BFIN_UART_NR_PORTS,
1239 .cons = BFIN_SERIAL_CONSOLE,
1240};
1241
1242static int bfin_serial_suspend(struct platform_device *pdev, pm_message_t state)
1243{
1244 struct bfin_serial_port *uart = platform_get_drvdata(pdev);
1245
1246 return uart_suspend_port(&bfin_serial_reg, &uart->port);
1247}
1248
1249static int bfin_serial_resume(struct platform_device *pdev)
1250{
1251 struct bfin_serial_port *uart = platform_get_drvdata(pdev);
1252
1253 return uart_resume_port(&bfin_serial_reg, &uart->port);
1254}
1255
1256static int bfin_serial_probe(struct platform_device *pdev)
1257{
1258 struct resource *res;
1259 struct bfin_serial_port *uart = NULL;
1260 int ret = 0;
1261
1262 if (pdev->id < 0 || pdev->id >= BFIN_UART_NR_PORTS) {
1263 dev_err(&pdev->dev, "Wrong bfin uart platform device id.\n");
1264 return -ENOENT;
1265 }
1266
1267 if (bfin_serial_ports[pdev->id] == NULL) {
1268
1269 uart = kzalloc(sizeof(*uart), GFP_KERNEL);
1270 if (!uart) {
1271 dev_err(&pdev->dev,
1272 "fail to malloc bfin_serial_port\n");
1273 return -ENOMEM;
1274 }
1275 bfin_serial_ports[pdev->id] = uart;
1276
1277#ifdef CONFIG_EARLY_PRINTK
1278 if (!(bfin_earlyprintk_port.port.membase
1279 && bfin_earlyprintk_port.port.line == pdev->id)) {
1280 /*
1281 * If the peripheral PINs of current port is allocated
1282 * in earlyprintk probe stage, don't do it again.
1283 */
1284#endif
1285 ret = peripheral_request_list(
1286 (unsigned short *)pdev->dev.platform_data, DRIVER_NAME);
1287 if (ret) {
1288 dev_err(&pdev->dev,
1289 "fail to request bfin serial peripherals\n");
1290 goto out_error_free_mem;
1291 }
1292#ifdef CONFIG_EARLY_PRINTK
1293 }
1294#endif
1295
1296 spin_lock_init(&uart->port.lock);
1297 uart->port.uartclk = get_sclk();
1298 uart->port.fifosize = BFIN_UART_TX_FIFO_SIZE;
1299 uart->port.ops = &bfin_serial_pops;
1300 uart->port.line = pdev->id;
1301 uart->port.iotype = UPIO_MEM;
1302 uart->port.flags = UPF_BOOT_AUTOCONF;
1303
1304 res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
1305 if (res == NULL) {
1306 dev_err(&pdev->dev, "Cannot get IORESOURCE_MEM\n");
1307 ret = -ENOENT;
1308 goto out_error_free_peripherals;
1309 }
1310
1311 uart->port.membase = ioremap(res->start,
1312 res->end - res->start);
1313 if (!uart->port.membase) {
1314 dev_err(&pdev->dev, "Cannot map uart IO\n");
1315 ret = -ENXIO;
1316 goto out_error_free_peripherals;
1317 }
1318 uart->port.mapbase = res->start;
1319
1320 uart->port.irq = platform_get_irq(pdev, 0);
1321 if (uart->port.irq < 0) {
1322 dev_err(&pdev->dev, "No uart RX/TX IRQ specified\n");
1323 ret = -ENOENT;
1324 goto out_error_unmap;
1325 }
1326
1327 uart->status_irq = platform_get_irq(pdev, 1);
1328 if (uart->status_irq < 0) {
1329 dev_err(&pdev->dev, "No uart status IRQ specified\n");
1330 ret = -ENOENT;
1331 goto out_error_unmap;
1332 }
1333
1334#ifdef CONFIG_SERIAL_BFIN_DMA
1335 uart->tx_done = 1;
1336 uart->tx_count = 0;
1337
1338 res = platform_get_resource(pdev, IORESOURCE_DMA, 0);
1339 if (res == NULL) {
1340 dev_err(&pdev->dev, "No uart TX DMA channel specified\n");
1341 ret = -ENOENT;
1342 goto out_error_unmap;
1343 }
1344 uart->tx_dma_channel = res->start;
1345
1346 res = platform_get_resource(pdev, IORESOURCE_DMA, 1);
1347 if (res == NULL) {
1348 dev_err(&pdev->dev, "No uart RX DMA channel specified\n");
1349 ret = -ENOENT;
1350 goto out_error_unmap;
1351 }
1352 uart->rx_dma_channel = res->start;
1353
1354 init_timer(&(uart->rx_dma_timer));
1355#endif
1356
1357#if defined(CONFIG_SERIAL_BFIN_CTSRTS) || \
1358 defined(CONFIG_SERIAL_BFIN_HARD_CTSRTS)
1359 res = platform_get_resource(pdev, IORESOURCE_IO, 0);
1360 if (res == NULL)
1361 uart->cts_pin = -1;
1362 else
1363 uart->cts_pin = res->start;
1364
1365 res = platform_get_resource(pdev, IORESOURCE_IO, 1);
1366 if (res == NULL)
1367 uart->rts_pin = -1;
1368 else
1369 uart->rts_pin = res->start;
1370# if defined(CONFIG_SERIAL_BFIN_CTSRTS)
1371 if (uart->rts_pin >= 0)
1372 gpio_request(uart->rts_pin, DRIVER_NAME);
1373# endif
1374#endif
1375 }
1376
1377#ifdef CONFIG_SERIAL_BFIN_CONSOLE
1378 if (!is_early_platform_device(pdev)) {
1379#endif
1380 uart = bfin_serial_ports[pdev->id];
1381 uart->port.dev = &pdev->dev;
1382 dev_set_drvdata(&pdev->dev, uart);
1383 ret = uart_add_one_port(&bfin_serial_reg, &uart->port);
1384#ifdef CONFIG_SERIAL_BFIN_CONSOLE
1385 }
1386#endif
1387
1388 if (!ret)
1389 return 0;
1390
1391 if (uart) {
1392out_error_unmap:
1393 iounmap(uart->port.membase);
1394out_error_free_peripherals:
1395 peripheral_free_list(
1396 (unsigned short *)pdev->dev.platform_data);
1397out_error_free_mem:
1398 kfree(uart);
1399 bfin_serial_ports[pdev->id] = NULL;
1400 }
1401
1402 return ret;
1403}
1404
1405static int __devexit bfin_serial_remove(struct platform_device *pdev)
1406{
1407 struct bfin_serial_port *uart = platform_get_drvdata(pdev);
1408
1409 dev_set_drvdata(&pdev->dev, NULL);
1410
1411 if (uart) {
1412 uart_remove_one_port(&bfin_serial_reg, &uart->port);
1413#ifdef CONFIG_SERIAL_BFIN_CTSRTS
1414 if (uart->rts_pin >= 0)
1415 gpio_free(uart->rts_pin);
1416#endif
1417 iounmap(uart->port.membase);
1418 peripheral_free_list(
1419 (unsigned short *)pdev->dev.platform_data);
1420 kfree(uart);
1421 bfin_serial_ports[pdev->id] = NULL;
1422 }
1423
1424 return 0;
1425}
1426
1427static struct platform_driver bfin_serial_driver = {
1428 .probe = bfin_serial_probe,
1429 .remove = __devexit_p(bfin_serial_remove),
1430 .suspend = bfin_serial_suspend,
1431 .resume = bfin_serial_resume,
1432 .driver = {
1433 .name = DRIVER_NAME,
1434 .owner = THIS_MODULE,
1435 },
1436};
1437
1438#if defined(CONFIG_SERIAL_BFIN_CONSOLE)
1439static __initdata struct early_platform_driver early_bfin_serial_driver = {
1440 .class_str = CLASS_BFIN_CONSOLE,
1441 .pdrv = &bfin_serial_driver,
1442 .requested_id = EARLY_PLATFORM_ID_UNSET,
1443};
1444
1445static int __init bfin_serial_rs_console_init(void)
1446{
1447 early_platform_driver_register(&early_bfin_serial_driver, DRIVER_NAME);
1448
1449 early_platform_driver_probe(CLASS_BFIN_CONSOLE, BFIN_UART_NR_PORTS, 0);
1450
1451 register_console(&bfin_serial_console);
1452
1453 return 0;
1454}
1455console_initcall(bfin_serial_rs_console_init);
1456#endif
1457
1458#ifdef CONFIG_EARLY_PRINTK
1459/*
1460 * Memory can't be allocated dynamically during earlyprink init stage.
1461 * So, do individual probe for earlyprink with a static uart port variable.
1462 */
1463static int bfin_earlyprintk_probe(struct platform_device *pdev)
1464{
1465 struct resource *res;
1466 int ret;
1467
1468 if (pdev->id < 0 || pdev->id >= BFIN_UART_NR_PORTS) {
1469 dev_err(&pdev->dev, "Wrong earlyprintk platform device id.\n");
1470 return -ENOENT;
1471 }
1472
1473 ret = peripheral_request_list(
1474 (unsigned short *)pdev->dev.platform_data, DRIVER_NAME);
1475 if (ret) {
1476 dev_err(&pdev->dev,
1477 "fail to request bfin serial peripherals\n");
1478 return ret;
1479 }
1480
1481 res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
1482 if (res == NULL) {
1483 dev_err(&pdev->dev, "Cannot get IORESOURCE_MEM\n");
1484 ret = -ENOENT;
1485 goto out_error_free_peripherals;
1486 }
1487
1488 bfin_earlyprintk_port.port.membase = ioremap(res->start,
1489 res->end - res->start);
1490 if (!bfin_earlyprintk_port.port.membase) {
1491 dev_err(&pdev->dev, "Cannot map uart IO\n");
1492 ret = -ENXIO;
1493 goto out_error_free_peripherals;
1494 }
1495 bfin_earlyprintk_port.port.mapbase = res->start;
1496 bfin_earlyprintk_port.port.line = pdev->id;
1497 bfin_earlyprintk_port.port.uartclk = get_sclk();
1498 bfin_earlyprintk_port.port.fifosize = BFIN_UART_TX_FIFO_SIZE;
1499 spin_lock_init(&bfin_earlyprintk_port.port.lock);
1500
1501 return 0;
1502
1503out_error_free_peripherals:
1504 peripheral_free_list(
1505 (unsigned short *)pdev->dev.platform_data);
1506
1507 return ret;
1508}
1509
1510static struct platform_driver bfin_earlyprintk_driver = {
1511 .probe = bfin_earlyprintk_probe,
1512 .driver = {
1513 .name = DRIVER_NAME,
1514 .owner = THIS_MODULE,
1515 },
1516};
1517
1518static __initdata struct early_platform_driver early_bfin_earlyprintk_driver = {
1519 .class_str = CLASS_BFIN_EARLYPRINTK,
1520 .pdrv = &bfin_earlyprintk_driver,
1521 .requested_id = EARLY_PLATFORM_ID_UNSET,
1522};
Robin Getz0ae53642007-10-09 17:24:49 +08001523
1524struct console __init *bfin_earlyserial_init(unsigned int port,
1525 unsigned int cflag)
1526{
Robin Getz0ae53642007-10-09 17:24:49 +08001527 struct ktermios t;
Sonic Zhang57afb392009-09-09 10:46:19 +00001528 char port_name[20];
1529
1530 if (port < 0 || port >= BFIN_UART_NR_PORTS)
1531 return NULL;
1532
1533 /*
1534 * Only probe resource of the given port in earlyprintk boot arg.
1535 * The expected port id should be indicated in port name string.
1536 */
1537 snprintf(port_name, 20, DRIVER_NAME ".%d", port);
1538 early_platform_driver_register(&early_bfin_earlyprintk_driver,
1539 port_name);
1540 early_platform_driver_probe(CLASS_BFIN_EARLYPRINTK, 1, 0);
1541
1542 if (!bfin_earlyprintk_port.port.membase)
1543 return NULL;
Robin Getz0ae53642007-10-09 17:24:49 +08001544
Sonic Zhang6d9e4492010-10-27 04:16:49 -04001545#ifdef CONFIG_SERIAL_BFIN_CONSOLE
1546 /*
1547 * If we are using early serial, don't let the normal console rewind
1548 * log buffer, since that causes things to be printed multiple times
1549 */
1550 bfin_serial_console.flags &= ~CON_PRINTBUFFER;
1551#endif
1552
Robin Getz0ae53642007-10-09 17:24:49 +08001553 bfin_early_serial_console.index = port;
Robin Getz0ae53642007-10-09 17:24:49 +08001554 t.c_cflag = cflag;
1555 t.c_iflag = 0;
1556 t.c_oflag = 0;
1557 t.c_lflag = ICANON;
1558 t.c_line = port;
Sonic Zhang57afb392009-09-09 10:46:19 +00001559 bfin_serial_set_termios(&bfin_earlyprintk_port.port, &t, &t);
1560
Robin Getz0ae53642007-10-09 17:24:49 +08001561 return &bfin_early_serial_console;
1562}
Sonic Zhangb6efa1e2009-01-02 13:40:31 +00001563#endif /* CONFIG_EARLY_PRINTK */
Bryan Wu194de562007-05-06 14:50:30 -07001564
Bryan Wu194de562007-05-06 14:50:30 -07001565static int __init bfin_serial_init(void)
1566{
1567 int ret;
1568
Sonic Zhang57afb392009-09-09 10:46:19 +00001569 pr_info("Blackfin serial driver\n");
Bryan Wu194de562007-05-06 14:50:30 -07001570
1571 ret = uart_register_driver(&bfin_serial_reg);
Sonic Zhang57afb392009-09-09 10:46:19 +00001572 if (ret) {
1573 pr_err("failed to register %s:%d\n",
1574 bfin_serial_reg.driver_name, ret);
Bryan Wu194de562007-05-06 14:50:30 -07001575 }
Sonic Zhang57afb392009-09-09 10:46:19 +00001576
1577 ret = platform_driver_register(&bfin_serial_driver);
1578 if (ret) {
1579 pr_err("fail to register bfin uart\n");
1580 uart_unregister_driver(&bfin_serial_reg);
1581 }
1582
Bryan Wu194de562007-05-06 14:50:30 -07001583 return ret;
1584}
1585
1586static void __exit bfin_serial_exit(void)
1587{
1588 platform_driver_unregister(&bfin_serial_driver);
1589 uart_unregister_driver(&bfin_serial_reg);
1590}
1591
Sonic Zhang52e15f02009-01-02 13:40:14 +00001592
Bryan Wu194de562007-05-06 14:50:30 -07001593module_init(bfin_serial_init);
1594module_exit(bfin_serial_exit);
1595
Sonic Zhang57afb392009-09-09 10:46:19 +00001596MODULE_AUTHOR("Sonic Zhang, Aubrey Li");
Bryan Wu194de562007-05-06 14:50:30 -07001597MODULE_DESCRIPTION("Blackfin generic serial port driver");
1598MODULE_LICENSE("GPL");
1599MODULE_ALIAS_CHARDEV_MAJOR(BFIN_SERIAL_MAJOR);
Kay Sieverse169c132008-04-15 14:34:35 -07001600MODULE_ALIAS("platform:bfin-uart");