blob: 3f5de867acd7cb4b9dd7229194e8c14f7bdea840 [file] [log] [blame]
Linus Torvalds1da177e2005-04-16 15:20:36 -07001menu "Bus options (PCI, PCMCIA, EISA, GSC, ISA)"
2
3config GSC
4 bool "VSC/GSC/HSC bus support"
5 default y
6 help
7 The VSC, GSC and HSC busses were used from the earliest 700-series
8 workstations up to and including the C360/J2240 workstations. They
9 were also used in servers from the E-class to the K-class. They
10 are not found in B1000, C3000, J5000, A500, L1000, N4000 and upwards.
11 If in doubt, say "Y".
12
13config HPPB
14 bool "HP-PB bus support"
15 depends on GSC
16 help
17 The HP-PB bus was used in the Nova class and K-class servers.
18 If in doubt, say "Y"
19
20config IOMMU_CCIO
21 bool "U2/Uturn I/O MMU"
22 depends on GSC
23 help
24 Say Y here to enable DMA management routines for the first
25 generation of PA-RISC cache-coherent machines. Programs the
26 U2/Uturn chip in "Virtual Mode" and use the I/O MMU.
27
28config GSC_LASI
29 bool "Lasi I/O support"
30 depends on GSC
31 help
32 Say Y here to support the Lasi multifunction chip found in
33 many PA-RISC workstations & servers. It includes interfaces
34 for a parallel port, serial port, NCR 53c710 SCSI, Apricot
35 Ethernet, Harmony audio, PS/2 keyboard & mouse, ISDN, telephony
36 and floppy. Note that you must still enable all the individual
37 drivers for these chips.
38
39config GSC_WAX
40 bool "Wax I/O support"
41 depends on GSC
42 help
43 Say Y here to support the Wax multifunction chip found in some
44 older systems, including B/C/D/R class and 715/64, 715/80 and
45 715/100. Wax includes an EISA adapter, a serial port (not always
46 used), a HIL interface chip and is also known to be used as the
47 GSC bridge for an X.25 GSC card.
48
49config EISA
50 bool "EISA support"
51 depends on GSC
52 help
53 Say Y here if you have an EISA bus in your machine. This code
54 supports both the Mongoose & Wax EISA adapters. It is sadly
55 incomplete and lacks support for card-to-host DMA.
56
57source "drivers/eisa/Kconfig"
58
59config ISA
60 bool "ISA support"
61 depends on EISA
62 help
63 If you want to plug an ISA card into your EISA bus, say Y here.
64 Most people should say N.
65
66config PCI
67 bool "PCI support"
68 help
69 All recent HP machines have PCI slots, and you should say Y here
70 if you have a recent machine. If you are convinced you do not have
71 PCI slots in your machine (eg a 712), then you may say "N" here.
72 Beware that some GSC cards have a Dino onboard and PCI inside them,
73 so it may be safest to say "Y" anyway.
74
75source "drivers/pci/Kconfig"
76
77config GSC_DINO
78 bool "GSCtoPCI/Dino PCI support"
79 depends on PCI && GSC
80 help
81 Say Y here to support the Dino & Cujo GSC to PCI bridges found in
82 machines from the B132 to the C360, the J2240 and the A180. Some
83 GSC/HSC cards (eg gigabit & dual 100 Mbit Ethernet) have a Dino on
84 the card, and you also need to say Y here if you have such a card.
85 Note that Dino also supplies one of the serial ports on certain
86 machines. If in doubt, say Y.
87
88config PCI_LBA
89 bool "LBA/Elroy PCI support"
90 depends on PCI
91 help
92 Say Y here to support the Elroy PCI Lower Bus Adapter. This is
93 present on B, C, J, L and N-class machines with 4-digit model
94 numbers and the A400/A500.
95
96config IOSAPIC
97 bool
98 depends on PCI_LBA
99 default PCI_LBA
100
101config IOMMU_SBA
102 bool
103 depends on PCI_LBA
104 default PCI_LBA
105
106#config PCI_EPIC
107# bool "EPIC/SAGA PCI support"
108# depends on PCI
109# default y
110# help
111# Say Y here for V-class PCI, DMA/IOMMU, IRQ subsystem support.
112
113source "drivers/pcmcia/Kconfig"
114
115source "drivers/pci/hotplug/Kconfig"
116
117endmenu
118
119menu "PA-RISC specific drivers"
120
121config SUPERIO
122 bool "SuperIO (SuckyIO) support"
123 depends on PCI_LBA
124 default y
125 help
126 Say Y here to support the SuperIO chip found in Bxxxx, C3xxx and
127 J5xxx+ machines. This enables IDE, Floppy, Parallel Port, and
128 Serial port on those machines.
129
130config CHASSIS_LCD_LED
131 bool "Chassis LCD and LED support"
132 default y
133 help
134 Say Y here if you want to enable support for the Heartbeat,
135 Disk/Network activities LEDs on some PA-RISC machines,
136 or support for the LCD that can be found on recent material.
137
138 This has nothing to do with LED State support for A and E class.
139
140 If unsure, say Y.
141
142config PDC_CHASSIS
143 bool "PDC chassis State Panel support"
144 default y
145 help
146 Say Y here if you want to enable support for the LED State front
147 panel as found on E class, and support for the GSP Virtual Front
148 Panel (LED State and message logging) as found on high end
149 servers such as A, L and N-class.
150
151 This has nothing to do with Chassis LCD and LED support.
152
153 If unsure, say Y.
154
155config PDC_STABLE
156 tristate "PDC Stable Storage support"
157 depends on SYSFS
158 default y
159 help
160 Say Y here if you want to enable support for accessing Stable Storage
161 variables (PDC non volatile variables such as Primary Boot Path,
162 Console Path, Autoboot, Autosearch, etc) through SysFS.
163
164 If unsure, say Y.
165
166 To compile this driver as a module, choose M here.
167 The module will be called pdc_stable.
168
169endmenu