blob: a24b459dd45aecf9ba8e1214fce68fe2b8330c6c [file] [log] [blame]
Jiri Bencf0706e822007-05-05 11:45:53 -07001config MAC80211
2 tristate "Generic IEEE 802.11 Networking Stack (mac80211)"
Jiri Bencf0706e822007-05-05 11:45:53 -07003 select CRYPTO
4 select CRYPTO_ECB
5 select CRYPTO_ARC4
6 select CRYPTO_AES
7 select CRC32
8 select WIRELESS_EXT
9 select CFG80211
10 select NET_SCH_FIFO
11 ---help---
John W. Linvillec40896d2007-12-21 00:44:59 -050012 This option enables the hardware independent IEEE 802.11
13 networking stack.
Jiri Bencf0706e822007-05-05 11:45:53 -070014
Johannes Berg4b475892008-01-02 15:17:03 +010015menu "Rate control algorithm selection"
16 depends on MAC80211 != n
Johannes Bergac71c692007-10-28 14:17:44 +010017
Stefano Brivioc21b39a2007-12-19 01:26:16 +010018choice
19 prompt "Default rate control algorithm"
20 default MAC80211_RC_DEFAULT_PID
Stefano Brivioc21b39a2007-12-19 01:26:16 +010021 ---help---
22 This option selects the default rate control algorithm
23 mac80211 will use. Note that this default can still be
24 overriden through the ieee80211_default_rc_algo module
Johannes Berg4b475892008-01-02 15:17:03 +010025 parameter if different algorithms are available.
Johannes Bergac71c692007-10-28 14:17:44 +010026
Stefano Brivioc21b39a2007-12-19 01:26:16 +010027config MAC80211_RC_DEFAULT_PID
28 bool "PID controller based rate control algorithm"
29 select MAC80211_RC_PID
30 ---help---
31 Select the PID controller based rate control as the
32 default rate control algorithm. You should choose
33 this unless you know what you are doing.
34
Johannes Berg4b475892008-01-02 15:17:03 +010035config MAC80211_RC_DEFAULT_NONE
36 bool "No default algorithm"
37 depends on EMBEDDED
38 help
39 Selecting this option will select no default algorithm
40 and allow you to not build any. Do not choose this
41 option unless you know your driver comes with another
42 suitable algorithm.
Stefano Brivioc21b39a2007-12-19 01:26:16 +010043endchoice
44
Johannes Berg4b475892008-01-02 15:17:03 +010045comment "Selecting 'y' for an algorithm will"
46comment "build the algorithm into mac80211."
47
Stefano Brivioc21b39a2007-12-19 01:26:16 +010048config MAC80211_RC_DEFAULT
49 string
Stefano Brivioc21b39a2007-12-19 01:26:16 +010050 default "pid" if MAC80211_RC_DEFAULT_PID
Stefano Brivioc21b39a2007-12-19 01:26:16 +010051 default ""
52
53config MAC80211_RC_PID
Johannes Berg4b475892008-01-02 15:17:03 +010054 tristate "PID controller based rate control algorithm"
Stefano Brivioc21b39a2007-12-19 01:26:16 +010055 ---help---
Mattias Nisslerad018372007-12-19 01:25:57 +010056 This option enables a TX rate control algorithm for
57 mac80211 that uses a PID controller to select the TX
58 rate.
59
Stefano Brivioc21b39a2007-12-19 01:26:16 +010060 Say Y or M unless you're sure you want to use a
61 different rate control algorithm.
62
Johannes Berg4b475892008-01-02 15:17:03 +010063endmenu
Mattias Nisslerad018372007-12-19 01:25:57 +010064
Johannes Berg2f5ce792008-02-23 15:17:21 +010065config MAC80211_MESH
66 bool "Enable mac80211 mesh networking (pre-802.11s) support"
Luis Carlos Cobo37659ff2008-02-29 12:13:38 -080067 depends on MAC80211 && EXPERIMENTAL
Johannes Berg2f5ce792008-02-23 15:17:21 +010068 ---help---
Johannes Berg5c142e82008-02-25 10:13:31 +010069 This options enables support of Draft 802.11s mesh networking.
70 The implementation is based on Draft 1.08 of the Mesh Networking
71 amendment. For more information visit http://o11s.org/.
Johannes Berg2f5ce792008-02-23 15:17:21 +010072
73
Jiri Bencf0706e822007-05-05 11:45:53 -070074config MAC80211_LEDS
75 bool "Enable LED triggers"
Luca Tettamantibd8fd212008-04-27 15:34:55 -070076 depends on MAC80211
77 select NEW_LEDS
78 select LEDS_TRIGGERS
Jiri Bencf0706e822007-05-05 11:45:53 -070079 ---help---
John W. Linvillec40896d2007-12-21 00:44:59 -050080 This option enables a few LED triggers for different
81 packet receive/transmit events.
Jiri Bencf0706e822007-05-05 11:45:53 -070082
Jiri Bence9f207f2007-05-05 11:46:38 -070083config MAC80211_DEBUGFS
84 bool "Export mac80211 internals in DebugFS"
85 depends on MAC80211 && DEBUG_FS
86 ---help---
87 Select this to see extensive information about
88 the internal state of mac80211 in debugfs.
89
90 Say N unless you know you need this.
91
Johannes Berg6feeb8a2008-01-29 16:57:51 +010092config MAC80211_DEBUG_PACKET_ALIGNMENT
93 bool "Enable packet alignment debugging"
94 depends on MAC80211
95 help
96 This option is recommended for driver authors and strongly
97 discouraged for everybody else, it will trigger a warning
98 when a driver hands mac80211 a buffer that is aligned in
99 a way that will cause problems with the IP stack on some
100 architectures.
101
102 Say N unless you're writing a mac80211 based driver.
103
Jiri Bencf0706e822007-05-05 11:45:53 -0700104config MAC80211_DEBUG
105 bool "Enable debugging output"
106 depends on MAC80211
107 ---help---
108 This option will enable debug tracing output for the
109 ieee80211 network stack.
110
111 If you are not trying to debug or develop the ieee80211
112 subsystem, you most likely want to say N here.
113
Ron Rindjunsky82b3cad2007-12-16 16:09:26 -0800114config MAC80211_HT_DEBUG
John W. Linvillec40896d2007-12-21 00:44:59 -0500115 bool "Enable HT debugging output"
116 depends on MAC80211_DEBUG
117 ---help---
118 This option enables 802.11n High Throughput features
119 debug tracing output.
Ron Rindjunsky82b3cad2007-12-16 16:09:26 -0800120
John W. Linvillec40896d2007-12-21 00:44:59 -0500121 If you are not trying to debug of develop the ieee80211
122 subsystem, you most likely want to say N here.
Ron Rindjunsky82b3cad2007-12-16 16:09:26 -0800123
Jiri Bencf0706e822007-05-05 11:45:53 -0700124config MAC80211_VERBOSE_DEBUG
125 bool "Verbose debugging output"
126 depends on MAC80211_DEBUG
127
128config MAC80211_LOWTX_FRAME_DUMP
129 bool "Debug frame dumping"
130 depends on MAC80211_DEBUG
131 ---help---
132 Selecting this option will cause the stack to
133 print a message for each frame that is handed
134 to the lowlevel driver for transmission. This
135 message includes all MAC addresses and the
136 frame control field.
137
138 If unsure, say N and insert the debugging code
139 you require into the driver you are debugging.
140
141config TKIP_DEBUG
142 bool "TKIP debugging"
143 depends on MAC80211_DEBUG
144
145config MAC80211_DEBUG_COUNTERS
146 bool "Extra statistics for TX/RX debugging"
147 depends on MAC80211_DEBUG
148
149config MAC80211_IBSS_DEBUG
150 bool "Support for IBSS testing"
151 depends on MAC80211_DEBUG
152 ---help---
153 Say Y here if you intend to debug the IBSS code.
154
155config MAC80211_VERBOSE_PS_DEBUG
156 bool "Verbose powersave mode debugging"
157 depends on MAC80211_DEBUG
158 ---help---
159 Say Y here to print out verbose powersave
160 mode debug messages.
Johannes Berg2f5ce792008-02-23 15:17:21 +0100161
162config MAC80211_VERBOSE_MPL_DEBUG
163 bool "Verbose mesh peer link debugging"
164 depends on MAC80211_DEBUG && MAC80211_MESH
165 ---help---
166 Say Y here to print out verbose mesh peer link
167 debug messages.