blob: ea5bf4d4daa3016db79933b268ae5240fa63e952 [file] [log] [blame]
Linus Torvalds1da177e2005-04-16 15:20:36 -07001/*
2 * Driver for Zilog serial chips found on SGI workstations and
3 * servers. This driver could actually be made more generic.
4 *
5 * This is based on the drivers/serial/sunzilog.c code as of 2.6.0-test7 and the
6 * old drivers/sgi/char/sgiserial.c code which itself is based of the original
7 * drivers/sbus/char/zs.c code. A lot of code has been simply moved over
8 * directly from there but much has been rewritten. Credits therefore go out
9 * to David S. Miller, Eddie C. Dost, Pete Zaitcev, Ted Ts'o and Alex Buell
10 * for their work there.
11 *
12 * Copyright (C) 2002 Ralf Baechle (ralf@linux-mips.org)
13 * Copyright (C) 2002 David S. Miller (davem@redhat.com)
14 */
15#include <linux/config.h>
16#include <linux/module.h>
17#include <linux/kernel.h>
18#include <linux/sched.h>
19#include <linux/errno.h>
20#include <linux/delay.h>
21#include <linux/tty.h>
22#include <linux/tty_flip.h>
23#include <linux/major.h>
24#include <linux/string.h>
25#include <linux/ptrace.h>
26#include <linux/ioport.h>
27#include <linux/slab.h>
28#include <linux/circ_buf.h>
29#include <linux/serial.h>
30#include <linux/sysrq.h>
31#include <linux/console.h>
32#include <linux/spinlock.h>
33#include <linux/init.h>
34
35#include <asm/io.h>
36#include <asm/irq.h>
37#include <asm/sgialib.h>
38#include <asm/sgi/ioc.h>
39#include <asm/sgi/hpc3.h>
40#include <asm/sgi/ip22.h>
41
42#if defined(CONFIG_SERIAL_IP22_ZILOG_CONSOLE) && defined(CONFIG_MAGIC_SYSRQ)
43#define SUPPORT_SYSRQ
44#endif
45
46#include <linux/serial_core.h>
47
48#include "ip22zilog.h"
49
50void ip22_do_break(void);
51
52/*
53 * On IP22 we need to delay after register accesses but we do not need to
54 * flush writes.
55 */
56#define ZSDELAY() udelay(5)
57#define ZSDELAY_LONG() udelay(20)
58#define ZS_WSYNC(channel) do { } while (0)
59
60#define NUM_IP22ZILOG 1
61#define NUM_CHANNELS (NUM_IP22ZILOG * 2)
62
63#define ZS_CLOCK 3672000 /* Zilog input clock rate. */
64#define ZS_CLOCK_DIVISOR 16 /* Divisor this driver uses. */
65
66/*
67 * We wrap our port structure around the generic uart_port.
68 */
69struct uart_ip22zilog_port {
70 struct uart_port port;
71
72 /* IRQ servicing chain. */
73 struct uart_ip22zilog_port *next;
74
75 /* Current values of Zilog write registers. */
76 unsigned char curregs[NUM_ZSREGS];
77
78 unsigned int flags;
79#define IP22ZILOG_FLAG_IS_CONS 0x00000004
80#define IP22ZILOG_FLAG_IS_KGDB 0x00000008
81#define IP22ZILOG_FLAG_MODEM_STATUS 0x00000010
82#define IP22ZILOG_FLAG_IS_CHANNEL_A 0x00000020
83#define IP22ZILOG_FLAG_REGS_HELD 0x00000040
84#define IP22ZILOG_FLAG_TX_STOPPED 0x00000080
85#define IP22ZILOG_FLAG_TX_ACTIVE 0x00000100
86
87 unsigned int cflag;
88
89 /* L1-A keyboard break state. */
90 int kbd_id;
91 int l1_down;
92
93 unsigned char parity_mask;
94 unsigned char prev_status;
95};
96
97#define ZILOG_CHANNEL_FROM_PORT(PORT) ((struct zilog_channel *)((PORT)->membase))
98#define UART_ZILOG(PORT) ((struct uart_ip22zilog_port *)(PORT))
99#define IP22ZILOG_GET_CURR_REG(PORT, REGNUM) \
100 (UART_ZILOG(PORT)->curregs[REGNUM])
101#define IP22ZILOG_SET_CURR_REG(PORT, REGNUM, REGVAL) \
102 ((UART_ZILOG(PORT)->curregs[REGNUM]) = (REGVAL))
103#define ZS_IS_CONS(UP) ((UP)->flags & IP22ZILOG_FLAG_IS_CONS)
104#define ZS_IS_KGDB(UP) ((UP)->flags & IP22ZILOG_FLAG_IS_KGDB)
105#define ZS_WANTS_MODEM_STATUS(UP) ((UP)->flags & IP22ZILOG_FLAG_MODEM_STATUS)
106#define ZS_IS_CHANNEL_A(UP) ((UP)->flags & IP22ZILOG_FLAG_IS_CHANNEL_A)
107#define ZS_REGS_HELD(UP) ((UP)->flags & IP22ZILOG_FLAG_REGS_HELD)
108#define ZS_TX_STOPPED(UP) ((UP)->flags & IP22ZILOG_FLAG_TX_STOPPED)
109#define ZS_TX_ACTIVE(UP) ((UP)->flags & IP22ZILOG_FLAG_TX_ACTIVE)
110
111/* Reading and writing Zilog8530 registers. The delays are to make this
112 * driver work on the IP22 which needs a settling delay after each chip
113 * register access, other machines handle this in hardware via auxiliary
114 * flip-flops which implement the settle time we do in software.
115 *
116 * The port lock must be held and local IRQs must be disabled
117 * when {read,write}_zsreg is invoked.
118 */
119static unsigned char read_zsreg(struct zilog_channel *channel,
120 unsigned char reg)
121{
122 unsigned char retval;
123
124 writeb(reg, &channel->control);
125 ZSDELAY();
126 retval = readb(&channel->control);
127 ZSDELAY();
128
129 return retval;
130}
131
132static void write_zsreg(struct zilog_channel *channel,
133 unsigned char reg, unsigned char value)
134{
135 writeb(reg, &channel->control);
136 ZSDELAY();
137 writeb(value, &channel->control);
138 ZSDELAY();
139}
140
141static void ip22zilog_clear_fifo(struct zilog_channel *channel)
142{
143 int i;
144
145 for (i = 0; i < 32; i++) {
146 unsigned char regval;
147
148 regval = readb(&channel->control);
149 ZSDELAY();
150 if (regval & Rx_CH_AV)
151 break;
152
153 regval = read_zsreg(channel, R1);
154 readb(&channel->data);
155 ZSDELAY();
156
157 if (regval & (PAR_ERR | Rx_OVR | CRC_ERR)) {
158 writeb(ERR_RES, &channel->control);
159 ZSDELAY();
160 ZS_WSYNC(channel);
161 }
162 }
163}
164
165/* This function must only be called when the TX is not busy. The UART
166 * port lock must be held and local interrupts disabled.
167 */
168static void __load_zsregs(struct zilog_channel *channel, unsigned char *regs)
169{
170 int i;
171
172 /* Let pending transmits finish. */
173 for (i = 0; i < 1000; i++) {
174 unsigned char stat = read_zsreg(channel, R1);
175 if (stat & ALL_SNT)
176 break;
177 udelay(100);
178 }
179
180 writeb(ERR_RES, &channel->control);
181 ZSDELAY();
182 ZS_WSYNC(channel);
183
184 ip22zilog_clear_fifo(channel);
185
186 /* Disable all interrupts. */
187 write_zsreg(channel, R1,
188 regs[R1] & ~(RxINT_MASK | TxINT_ENAB | EXT_INT_ENAB));
189
190 /* Set parity, sync config, stop bits, and clock divisor. */
191 write_zsreg(channel, R4, regs[R4]);
192
193 /* Set misc. TX/RX control bits. */
194 write_zsreg(channel, R10, regs[R10]);
195
196 /* Set TX/RX controls sans the enable bits. */
197 write_zsreg(channel, R3, regs[R3] & ~RxENAB);
198 write_zsreg(channel, R5, regs[R5] & ~TxENAB);
199
200 /* Synchronous mode config. */
201 write_zsreg(channel, R6, regs[R6]);
202 write_zsreg(channel, R7, regs[R7]);
203
204 /* Don't mess with the interrupt vector (R2, unused by us) and
205 * master interrupt control (R9). We make sure this is setup
206 * properly at probe time then never touch it again.
207 */
208
209 /* Disable baud generator. */
210 write_zsreg(channel, R14, regs[R14] & ~BRENAB);
211
212 /* Clock mode control. */
213 write_zsreg(channel, R11, regs[R11]);
214
215 /* Lower and upper byte of baud rate generator divisor. */
216 write_zsreg(channel, R12, regs[R12]);
217 write_zsreg(channel, R13, regs[R13]);
218
219 /* Now rewrite R14, with BRENAB (if set). */
220 write_zsreg(channel, R14, regs[R14]);
221
222 /* External status interrupt control. */
223 write_zsreg(channel, R15, regs[R15]);
224
225 /* Reset external status interrupts. */
226 write_zsreg(channel, R0, RES_EXT_INT);
227 write_zsreg(channel, R0, RES_EXT_INT);
228
229 /* Rewrite R3/R5, this time without enables masked. */
230 write_zsreg(channel, R3, regs[R3]);
231 write_zsreg(channel, R5, regs[R5]);
232
233 /* Rewrite R1, this time without IRQ enabled masked. */
234 write_zsreg(channel, R1, regs[R1]);
235}
236
237/* Reprogram the Zilog channel HW registers with the copies found in the
238 * software state struct. If the transmitter is busy, we defer this update
239 * until the next TX complete interrupt. Else, we do it right now.
240 *
241 * The UART port lock must be held and local interrupts disabled.
242 */
243static void ip22zilog_maybe_update_regs(struct uart_ip22zilog_port *up,
244 struct zilog_channel *channel)
245{
246 if (!ZS_REGS_HELD(up)) {
247 if (ZS_TX_ACTIVE(up)) {
248 up->flags |= IP22ZILOG_FLAG_REGS_HELD;
249 } else {
250 __load_zsregs(channel, up->curregs);
251 }
252 }
253}
254
255static void ip22zilog_receive_chars(struct uart_ip22zilog_port *up,
256 struct zilog_channel *channel,
257 struct pt_regs *regs)
258{
259 struct tty_struct *tty = up->port.info->tty; /* XXX info==NULL? */
260
261 while (1) {
262 unsigned char ch, r1;
263
264 if (unlikely(tty->flip.count >= TTY_FLIPBUF_SIZE)) {
265 tty->flip.work.func((void *)tty);
266 if (tty->flip.count >= TTY_FLIPBUF_SIZE)
267 return; /* XXX Ignores SysRq when we need it most. Fix. */
268 }
269
270 r1 = read_zsreg(channel, R1);
271 if (r1 & (PAR_ERR | Rx_OVR | CRC_ERR)) {
272 writeb(ERR_RES, &channel->control);
273 ZSDELAY();
274 ZS_WSYNC(channel);
275 }
276
277 ch = readb(&channel->control);
278 ZSDELAY();
279
280 /* This funny hack depends upon BRK_ABRT not interfering
281 * with the other bits we care about in R1.
282 */
283 if (ch & BRK_ABRT)
284 r1 |= BRK_ABRT;
285
286 ch = readb(&channel->data);
287 ZSDELAY();
288
289 ch &= up->parity_mask;
290
291 if (ZS_IS_CONS(up) && (r1 & BRK_ABRT)) {
292 /* Wait for BREAK to deassert to avoid potentially
293 * confusing the PROM.
294 */
295 while (1) {
296 ch = readb(&channel->control);
297 ZSDELAY();
298 if (!(ch & BRK_ABRT))
299 break;
300 }
301 ip22_do_break();
302 return;
303 }
304
305 /* A real serial line, record the character and status. */
306 *tty->flip.char_buf_ptr = ch;
307 *tty->flip.flag_buf_ptr = TTY_NORMAL;
308 up->port.icount.rx++;
309 if (r1 & (BRK_ABRT | PAR_ERR | Rx_OVR | CRC_ERR)) {
310 if (r1 & BRK_ABRT) {
311 r1 &= ~(PAR_ERR | CRC_ERR);
312 up->port.icount.brk++;
313 if (uart_handle_break(&up->port))
314 goto next_char;
315 }
316 else if (r1 & PAR_ERR)
317 up->port.icount.parity++;
318 else if (r1 & CRC_ERR)
319 up->port.icount.frame++;
320 if (r1 & Rx_OVR)
321 up->port.icount.overrun++;
322 r1 &= up->port.read_status_mask;
323 if (r1 & BRK_ABRT)
324 *tty->flip.flag_buf_ptr = TTY_BREAK;
325 else if (r1 & PAR_ERR)
326 *tty->flip.flag_buf_ptr = TTY_PARITY;
327 else if (r1 & CRC_ERR)
328 *tty->flip.flag_buf_ptr = TTY_FRAME;
329 }
330 if (uart_handle_sysrq_char(&up->port, ch, regs))
331 goto next_char;
332
333 if (up->port.ignore_status_mask == 0xff ||
334 (r1 & up->port.ignore_status_mask) == 0) {
335 tty->flip.flag_buf_ptr++;
336 tty->flip.char_buf_ptr++;
337 tty->flip.count++;
338 }
339 if ((r1 & Rx_OVR) &&
340 tty->flip.count < TTY_FLIPBUF_SIZE) {
341 *tty->flip.flag_buf_ptr = TTY_OVERRUN;
342 tty->flip.flag_buf_ptr++;
343 tty->flip.char_buf_ptr++;
344 tty->flip.count++;
345 }
346 next_char:
347 ch = readb(&channel->control);
348 ZSDELAY();
349 if (!(ch & Rx_CH_AV))
350 break;
351 }
352
353 tty_flip_buffer_push(tty);
354}
355
356static void ip22zilog_status_handle(struct uart_ip22zilog_port *up,
357 struct zilog_channel *channel,
358 struct pt_regs *regs)
359{
360 unsigned char status;
361
362 status = readb(&channel->control);
363 ZSDELAY();
364
365 writeb(RES_EXT_INT, &channel->control);
366 ZSDELAY();
367 ZS_WSYNC(channel);
368
369 if (ZS_WANTS_MODEM_STATUS(up)) {
370 if (status & SYNC)
371 up->port.icount.dsr++;
372
373 /* The Zilog just gives us an interrupt when DCD/CTS/etc. change.
374 * But it does not tell us which bit has changed, we have to keep
375 * track of this ourselves.
376 */
377 if ((status & DCD) ^ up->prev_status)
378 uart_handle_dcd_change(&up->port,
379 (status & DCD));
380 if ((status & CTS) ^ up->prev_status)
381 uart_handle_cts_change(&up->port,
382 (status & CTS));
383
384 wake_up_interruptible(&up->port.info->delta_msr_wait);
385 }
386
387 up->prev_status = status;
388}
389
390static void ip22zilog_transmit_chars(struct uart_ip22zilog_port *up,
391 struct zilog_channel *channel)
392{
393 struct circ_buf *xmit;
394
395 if (ZS_IS_CONS(up)) {
396 unsigned char status = readb(&channel->control);
397 ZSDELAY();
398
399 /* TX still busy? Just wait for the next TX done interrupt.
400 *
401 * It can occur because of how we do serial console writes. It would
402 * be nice to transmit console writes just like we normally would for
403 * a TTY line. (ie. buffered and TX interrupt driven). That is not
404 * easy because console writes cannot sleep. One solution might be
405 * to poll on enough port->xmit space becomming free. -DaveM
406 */
407 if (!(status & Tx_BUF_EMP))
408 return;
409 }
410
411 up->flags &= ~IP22ZILOG_FLAG_TX_ACTIVE;
412
413 if (ZS_REGS_HELD(up)) {
414 __load_zsregs(channel, up->curregs);
415 up->flags &= ~IP22ZILOG_FLAG_REGS_HELD;
416 }
417
418 if (ZS_TX_STOPPED(up)) {
419 up->flags &= ~IP22ZILOG_FLAG_TX_STOPPED;
420 goto ack_tx_int;
421 }
422
423 if (up->port.x_char) {
424 up->flags |= IP22ZILOG_FLAG_TX_ACTIVE;
425 writeb(up->port.x_char, &channel->data);
426 ZSDELAY();
427 ZS_WSYNC(channel);
428
429 up->port.icount.tx++;
430 up->port.x_char = 0;
431 return;
432 }
433
434 if (up->port.info == NULL)
435 goto ack_tx_int;
436 xmit = &up->port.info->xmit;
437 if (uart_circ_empty(xmit)) {
438 uart_write_wakeup(&up->port);
439 goto ack_tx_int;
440 }
441 if (uart_tx_stopped(&up->port))
442 goto ack_tx_int;
443
444 up->flags |= IP22ZILOG_FLAG_TX_ACTIVE;
445 writeb(xmit->buf[xmit->tail], &channel->data);
446 ZSDELAY();
447 ZS_WSYNC(channel);
448
449 xmit->tail = (xmit->tail + 1) & (UART_XMIT_SIZE - 1);
450 up->port.icount.tx++;
451
452 if (uart_circ_chars_pending(xmit) < WAKEUP_CHARS)
453 uart_write_wakeup(&up->port);
454
455 return;
456
457ack_tx_int:
458 writeb(RES_Tx_P, &channel->control);
459 ZSDELAY();
460 ZS_WSYNC(channel);
461}
462
463static irqreturn_t ip22zilog_interrupt(int irq, void *dev_id, struct pt_regs *regs)
464{
465 struct uart_ip22zilog_port *up = dev_id;
466
467 while (up) {
468 struct zilog_channel *channel
469 = ZILOG_CHANNEL_FROM_PORT(&up->port);
470 unsigned char r3;
471
472 spin_lock(&up->port.lock);
473 r3 = read_zsreg(channel, R3);
474
475 /* Channel A */
476 if (r3 & (CHAEXT | CHATxIP | CHARxIP)) {
477 writeb(RES_H_IUS, &channel->control);
478 ZSDELAY();
479 ZS_WSYNC(channel);
480
481 if (r3 & CHARxIP)
482 ip22zilog_receive_chars(up, channel, regs);
483 if (r3 & CHAEXT)
484 ip22zilog_status_handle(up, channel, regs);
485 if (r3 & CHATxIP)
486 ip22zilog_transmit_chars(up, channel);
487 }
488 spin_unlock(&up->port.lock);
489
490 /* Channel B */
491 up = up->next;
492 channel = ZILOG_CHANNEL_FROM_PORT(&up->port);
493
494 spin_lock(&up->port.lock);
495 if (r3 & (CHBEXT | CHBTxIP | CHBRxIP)) {
496 writeb(RES_H_IUS, &channel->control);
497 ZSDELAY();
498 ZS_WSYNC(channel);
499
500 if (r3 & CHBRxIP)
501 ip22zilog_receive_chars(up, channel, regs);
502 if (r3 & CHBEXT)
503 ip22zilog_status_handle(up, channel, regs);
504 if (r3 & CHBTxIP)
505 ip22zilog_transmit_chars(up, channel);
506 }
507 spin_unlock(&up->port.lock);
508
509 up = up->next;
510 }
511
512 return IRQ_HANDLED;
513}
514
515/* A convenient way to quickly get R0 status. The caller must _not_ hold the
516 * port lock, it is acquired here.
517 */
518static __inline__ unsigned char ip22zilog_read_channel_status(struct uart_port *port)
519{
520 struct zilog_channel *channel;
Linus Torvalds1da177e2005-04-16 15:20:36 -0700521 unsigned char status;
522
Linus Torvalds1da177e2005-04-16 15:20:36 -0700523 channel = ZILOG_CHANNEL_FROM_PORT(port);
524 status = readb(&channel->control);
525 ZSDELAY();
526
Linus Torvalds1da177e2005-04-16 15:20:36 -0700527 return status;
528}
529
530/* The port lock is not held. */
531static unsigned int ip22zilog_tx_empty(struct uart_port *port)
532{
Russell Kingc5f46442005-06-29 09:42:38 +0100533 unsigned long flags;
Linus Torvalds1da177e2005-04-16 15:20:36 -0700534 unsigned char status;
535 unsigned int ret;
536
Russell Kingc5f46442005-06-29 09:42:38 +0100537 spin_lock_irqsave(&port->lock, flags);
538
Linus Torvalds1da177e2005-04-16 15:20:36 -0700539 status = ip22zilog_read_channel_status(port);
Russell Kingc5f46442005-06-29 09:42:38 +0100540
541 spin_unlock_irqrestore(&port->lock, flags);
542
Linus Torvalds1da177e2005-04-16 15:20:36 -0700543 if (status & Tx_BUF_EMP)
544 ret = TIOCSER_TEMT;
545 else
546 ret = 0;
547
548 return ret;
549}
550
Russell Kingc5f46442005-06-29 09:42:38 +0100551/* The port lock is held and interrupts are disabled. */
Linus Torvalds1da177e2005-04-16 15:20:36 -0700552static unsigned int ip22zilog_get_mctrl(struct uart_port *port)
553{
554 unsigned char status;
555 unsigned int ret;
556
557 status = ip22zilog_read_channel_status(port);
558
559 ret = 0;
560 if (status & DCD)
561 ret |= TIOCM_CAR;
562 if (status & SYNC)
563 ret |= TIOCM_DSR;
564 if (status & CTS)
565 ret |= TIOCM_CTS;
566
567 return ret;
568}
569
570/* The port lock is held and interrupts are disabled. */
571static void ip22zilog_set_mctrl(struct uart_port *port, unsigned int mctrl)
572{
573 struct uart_ip22zilog_port *up = (struct uart_ip22zilog_port *) port;
574 struct zilog_channel *channel = ZILOG_CHANNEL_FROM_PORT(port);
575 unsigned char set_bits, clear_bits;
576
577 set_bits = clear_bits = 0;
578
579 if (mctrl & TIOCM_RTS)
580 set_bits |= RTS;
581 else
582 clear_bits |= RTS;
583 if (mctrl & TIOCM_DTR)
584 set_bits |= DTR;
585 else
586 clear_bits |= DTR;
587
588 /* NOTE: Not subject to 'transmitter active' rule. */
589 up->curregs[R5] |= set_bits;
590 up->curregs[R5] &= ~clear_bits;
591 write_zsreg(channel, R5, up->curregs[R5]);
592}
593
594/* The port lock is held and interrupts are disabled. */
595static void ip22zilog_stop_tx(struct uart_port *port, unsigned int tty_stop)
596{
597 struct uart_ip22zilog_port *up = (struct uart_ip22zilog_port *) port;
598
599 up->flags |= IP22ZILOG_FLAG_TX_STOPPED;
600}
601
602/* The port lock is held and interrupts are disabled. */
603static void ip22zilog_start_tx(struct uart_port *port, unsigned int tty_start)
604{
605 struct uart_ip22zilog_port *up = (struct uart_ip22zilog_port *) port;
606 struct zilog_channel *channel = ZILOG_CHANNEL_FROM_PORT(port);
607 unsigned char status;
608
609 up->flags |= IP22ZILOG_FLAG_TX_ACTIVE;
610 up->flags &= ~IP22ZILOG_FLAG_TX_STOPPED;
611
612 status = readb(&channel->control);
613 ZSDELAY();
614
615 /* TX busy? Just wait for the TX done interrupt. */
616 if (!(status & Tx_BUF_EMP))
617 return;
618
619 /* Send the first character to jump-start the TX done
620 * IRQ sending engine.
621 */
622 if (port->x_char) {
623 writeb(port->x_char, &channel->data);
624 ZSDELAY();
625 ZS_WSYNC(channel);
626
627 port->icount.tx++;
628 port->x_char = 0;
629 } else {
630 struct circ_buf *xmit = &port->info->xmit;
631
632 writeb(xmit->buf[xmit->tail], &channel->data);
633 ZSDELAY();
634 ZS_WSYNC(channel);
635
636 xmit->tail = (xmit->tail + 1) & (UART_XMIT_SIZE - 1);
637 port->icount.tx++;
638
639 if (uart_circ_chars_pending(xmit) < WAKEUP_CHARS)
640 uart_write_wakeup(&up->port);
641 }
642}
643
644/* The port lock is held and interrupts are disabled. */
645static void ip22zilog_stop_rx(struct uart_port *port)
646{
647 struct uart_ip22zilog_port *up = UART_ZILOG(port);
648 struct zilog_channel *channel;
649
650 if (ZS_IS_CONS(up))
651 return;
652
653 channel = ZILOG_CHANNEL_FROM_PORT(port);
654
655 /* Disable all RX interrupts. */
656 up->curregs[R1] &= ~RxINT_MASK;
657 ip22zilog_maybe_update_regs(up, channel);
658}
659
660/* The port lock is held. */
661static void ip22zilog_enable_ms(struct uart_port *port)
662{
663 struct uart_ip22zilog_port *up = (struct uart_ip22zilog_port *) port;
664 struct zilog_channel *channel = ZILOG_CHANNEL_FROM_PORT(port);
665 unsigned char new_reg;
666
667 new_reg = up->curregs[R15] | (DCDIE | SYNCIE | CTSIE);
668 if (new_reg != up->curregs[R15]) {
669 up->curregs[R15] = new_reg;
670
671 /* NOTE: Not subject to 'transmitter active' rule. */
672 write_zsreg(channel, R15, up->curregs[R15]);
673 }
674}
675
676/* The port lock is not held. */
677static void ip22zilog_break_ctl(struct uart_port *port, int break_state)
678{
679 struct uart_ip22zilog_port *up = (struct uart_ip22zilog_port *) port;
680 struct zilog_channel *channel = ZILOG_CHANNEL_FROM_PORT(port);
681 unsigned char set_bits, clear_bits, new_reg;
682 unsigned long flags;
683
684 set_bits = clear_bits = 0;
685
686 if (break_state)
687 set_bits |= SND_BRK;
688 else
689 clear_bits |= SND_BRK;
690
691 spin_lock_irqsave(&port->lock, flags);
692
693 new_reg = (up->curregs[R5] | set_bits) & ~clear_bits;
694 if (new_reg != up->curregs[R5]) {
695 up->curregs[R5] = new_reg;
696
697 /* NOTE: Not subject to 'transmitter active' rule. */
698 write_zsreg(channel, R5, up->curregs[R5]);
699 }
700
701 spin_unlock_irqrestore(&port->lock, flags);
702}
703
704static void __ip22zilog_startup(struct uart_ip22zilog_port *up)
705{
706 struct zilog_channel *channel;
707
708 channel = ZILOG_CHANNEL_FROM_PORT(&up->port);
709 up->prev_status = readb(&channel->control);
710
711 /* Enable receiver and transmitter. */
712 up->curregs[R3] |= RxENAB;
713 up->curregs[R5] |= TxENAB;
714
715 up->curregs[R1] |= EXT_INT_ENAB | INT_ALL_Rx | TxINT_ENAB;
716 ip22zilog_maybe_update_regs(up, channel);
717}
718
719static int ip22zilog_startup(struct uart_port *port)
720{
721 struct uart_ip22zilog_port *up = UART_ZILOG(port);
722 unsigned long flags;
723
724 if (ZS_IS_CONS(up))
725 return 0;
726
727 spin_lock_irqsave(&port->lock, flags);
728 __ip22zilog_startup(up);
729 spin_unlock_irqrestore(&port->lock, flags);
730 return 0;
731}
732
733/*
734 * The test for ZS_IS_CONS is explained by the following e-mail:
735 *****
736 * From: Russell King <rmk@arm.linux.org.uk>
737 * Date: Sun, 8 Dec 2002 10:18:38 +0000
738 *
739 * On Sun, Dec 08, 2002 at 02:43:36AM -0500, Pete Zaitcev wrote:
740 * > I boot my 2.5 boxes using "console=ttyS0,9600" argument,
741 * > and I noticed that something is not right with reference
742 * > counting in this case. It seems that when the console
743 * > is open by kernel initially, this is not accounted
744 * > as an open, and uart_startup is not called.
745 *
746 * That is correct. We are unable to call uart_startup when the serial
747 * console is initialised because it may need to allocate memory (as
748 * request_irq does) and the memory allocators may not have been
749 * initialised.
750 *
751 * 1. initialise the port into a state where it can send characters in the
752 * console write method.
753 *
754 * 2. don't do the actual hardware shutdown in your shutdown() method (but
755 * do the normal software shutdown - ie, free irqs etc)
756 *****
757 */
758static void ip22zilog_shutdown(struct uart_port *port)
759{
760 struct uart_ip22zilog_port *up = UART_ZILOG(port);
761 struct zilog_channel *channel;
762 unsigned long flags;
763
764 if (ZS_IS_CONS(up))
765 return;
766
767 spin_lock_irqsave(&port->lock, flags);
768
769 channel = ZILOG_CHANNEL_FROM_PORT(port);
770
771 /* Disable receiver and transmitter. */
772 up->curregs[R3] &= ~RxENAB;
773 up->curregs[R5] &= ~TxENAB;
774
775 /* Disable all interrupts and BRK assertion. */
776 up->curregs[R1] &= ~(EXT_INT_ENAB | TxINT_ENAB | RxINT_MASK);
777 up->curregs[R5] &= ~SND_BRK;
778 ip22zilog_maybe_update_regs(up, channel);
779
780 spin_unlock_irqrestore(&port->lock, flags);
781}
782
783/* Shared by TTY driver and serial console setup. The port lock is held
784 * and local interrupts are disabled.
785 */
786static void
787ip22zilog_convert_to_zs(struct uart_ip22zilog_port *up, unsigned int cflag,
788 unsigned int iflag, int brg)
789{
790
791 up->curregs[R10] = NRZ;
792 up->curregs[R11] = TCBR | RCBR;
793
794 /* Program BAUD and clock source. */
795 up->curregs[R4] &= ~XCLK_MASK;
796 up->curregs[R4] |= X16CLK;
797 up->curregs[R12] = brg & 0xff;
798 up->curregs[R13] = (brg >> 8) & 0xff;
799 up->curregs[R14] = BRENAB;
800
801 /* Character size, stop bits, and parity. */
802 up->curregs[3] &= ~RxN_MASK;
803 up->curregs[5] &= ~TxN_MASK;
804 switch (cflag & CSIZE) {
805 case CS5:
806 up->curregs[3] |= Rx5;
807 up->curregs[5] |= Tx5;
808 up->parity_mask = 0x1f;
809 break;
810 case CS6:
811 up->curregs[3] |= Rx6;
812 up->curregs[5] |= Tx6;
813 up->parity_mask = 0x3f;
814 break;
815 case CS7:
816 up->curregs[3] |= Rx7;
817 up->curregs[5] |= Tx7;
818 up->parity_mask = 0x7f;
819 break;
820 case CS8:
821 default:
822 up->curregs[3] |= Rx8;
823 up->curregs[5] |= Tx8;
824 up->parity_mask = 0xff;
825 break;
826 };
827 up->curregs[4] &= ~0x0c;
828 if (cflag & CSTOPB)
829 up->curregs[4] |= SB2;
830 else
831 up->curregs[4] |= SB1;
832 if (cflag & PARENB)
833 up->curregs[4] |= PAR_ENAB;
834 else
835 up->curregs[4] &= ~PAR_ENAB;
836 if (!(cflag & PARODD))
837 up->curregs[4] |= PAR_EVEN;
838 else
839 up->curregs[4] &= ~PAR_EVEN;
840
841 up->port.read_status_mask = Rx_OVR;
842 if (iflag & INPCK)
843 up->port.read_status_mask |= CRC_ERR | PAR_ERR;
844 if (iflag & (BRKINT | PARMRK))
845 up->port.read_status_mask |= BRK_ABRT;
846
847 up->port.ignore_status_mask = 0;
848 if (iflag & IGNPAR)
849 up->port.ignore_status_mask |= CRC_ERR | PAR_ERR;
850 if (iflag & IGNBRK) {
851 up->port.ignore_status_mask |= BRK_ABRT;
852 if (iflag & IGNPAR)
853 up->port.ignore_status_mask |= Rx_OVR;
854 }
855
856 if ((cflag & CREAD) == 0)
857 up->port.ignore_status_mask = 0xff;
858}
859
860/* The port lock is not held. */
861static void
862ip22zilog_set_termios(struct uart_port *port, struct termios *termios,
863 struct termios *old)
864{
865 struct uart_ip22zilog_port *up = (struct uart_ip22zilog_port *) port;
866 unsigned long flags;
867 int baud, brg;
868
869 baud = uart_get_baud_rate(port, termios, old, 1200, 76800);
870
871 spin_lock_irqsave(&up->port.lock, flags);
872
873 brg = BPS_TO_BRG(baud, ZS_CLOCK / ZS_CLOCK_DIVISOR);
874
875 ip22zilog_convert_to_zs(up, termios->c_cflag, termios->c_iflag, brg);
876
877 if (UART_ENABLE_MS(&up->port, termios->c_cflag))
878 up->flags |= IP22ZILOG_FLAG_MODEM_STATUS;
879 else
880 up->flags &= ~IP22ZILOG_FLAG_MODEM_STATUS;
881
882 up->cflag = termios->c_cflag;
883
884 ip22zilog_maybe_update_regs(up, ZILOG_CHANNEL_FROM_PORT(port));
885
886 spin_unlock_irqrestore(&up->port.lock, flags);
887}
888
889static const char *ip22zilog_type(struct uart_port *port)
890{
891 return "IP22-Zilog";
892}
893
894/* We do not request/release mappings of the registers here, this
895 * happens at early serial probe time.
896 */
897static void ip22zilog_release_port(struct uart_port *port)
898{
899}
900
901static int ip22zilog_request_port(struct uart_port *port)
902{
903 return 0;
904}
905
906/* These do not need to do anything interesting either. */
907static void ip22zilog_config_port(struct uart_port *port, int flags)
908{
909}
910
911/* We do not support letting the user mess with the divisor, IRQ, etc. */
912static int ip22zilog_verify_port(struct uart_port *port, struct serial_struct *ser)
913{
914 return -EINVAL;
915}
916
917static struct uart_ops ip22zilog_pops = {
918 .tx_empty = ip22zilog_tx_empty,
919 .set_mctrl = ip22zilog_set_mctrl,
920 .get_mctrl = ip22zilog_get_mctrl,
921 .stop_tx = ip22zilog_stop_tx,
922 .start_tx = ip22zilog_start_tx,
923 .stop_rx = ip22zilog_stop_rx,
924 .enable_ms = ip22zilog_enable_ms,
925 .break_ctl = ip22zilog_break_ctl,
926 .startup = ip22zilog_startup,
927 .shutdown = ip22zilog_shutdown,
928 .set_termios = ip22zilog_set_termios,
929 .type = ip22zilog_type,
930 .release_port = ip22zilog_release_port,
931 .request_port = ip22zilog_request_port,
932 .config_port = ip22zilog_config_port,
933 .verify_port = ip22zilog_verify_port,
934};
935
936static struct uart_ip22zilog_port *ip22zilog_port_table;
937static struct zilog_layout **ip22zilog_chip_regs;
938
939static struct uart_ip22zilog_port *ip22zilog_irq_chain;
940static int zilog_irq = -1;
941
942static void * __init alloc_one_table(unsigned long size)
943{
944 void *ret;
945
946 ret = kmalloc(size, GFP_KERNEL);
947 if (ret != NULL)
948 memset(ret, 0, size);
949
950 return ret;
951}
952
953static void __init ip22zilog_alloc_tables(void)
954{
955 ip22zilog_port_table = (struct uart_ip22zilog_port *)
956 alloc_one_table(NUM_CHANNELS * sizeof(struct uart_ip22zilog_port));
957 ip22zilog_chip_regs = (struct zilog_layout **)
958 alloc_one_table(NUM_IP22ZILOG * sizeof(struct zilog_layout *));
959
960 if (ip22zilog_port_table == NULL || ip22zilog_chip_regs == NULL) {
961 panic("IP22-Zilog: Cannot allocate IP22-Zilog tables.");
962 }
963}
964
965/* Get the address of the registers for IP22-Zilog instance CHIP. */
966static struct zilog_layout * __init get_zs(int chip)
967{
968 unsigned long base;
969
970 if (chip < 0 || chip >= NUM_IP22ZILOG) {
971 panic("IP22-Zilog: Illegal chip number %d in get_zs.", chip);
972 }
973
974 /* Not probe-able, hard code it. */
975 base = (unsigned long) &sgioc->uart;
976
977 zilog_irq = SGI_SERIAL_IRQ;
978 request_mem_region(base, 8, "IP22-Zilog");
979
980 return (struct zilog_layout *) base;
981}
982
983#define ZS_PUT_CHAR_MAX_DELAY 2000 /* 10 ms */
984
985#ifdef CONFIG_SERIAL_IP22_ZILOG_CONSOLE
986static void ip22zilog_put_char(struct zilog_channel *channel, unsigned char ch)
987{
988 int loops = ZS_PUT_CHAR_MAX_DELAY;
989
990 /* This is a timed polling loop so do not switch the explicit
991 * udelay with ZSDELAY as that is a NOP on some platforms. -DaveM
992 */
993 do {
994 unsigned char val = readb(&channel->control);
995 if (val & Tx_BUF_EMP) {
996 ZSDELAY();
997 break;
998 }
999 udelay(5);
1000 } while (--loops);
1001
1002 writeb(ch, &channel->data);
1003 ZSDELAY();
1004 ZS_WSYNC(channel);
1005}
1006
1007static void
1008ip22zilog_console_write(struct console *con, const char *s, unsigned int count)
1009{
1010 struct uart_ip22zilog_port *up = &ip22zilog_port_table[con->index];
1011 struct zilog_channel *channel = ZILOG_CHANNEL_FROM_PORT(&up->port);
1012 unsigned long flags;
1013 int i;
1014
1015 spin_lock_irqsave(&up->port.lock, flags);
1016 for (i = 0; i < count; i++, s++) {
1017 ip22zilog_put_char(channel, *s);
1018 if (*s == 10)
1019 ip22zilog_put_char(channel, 13);
1020 }
1021 udelay(2);
1022 spin_unlock_irqrestore(&up->port.lock, flags);
1023}
1024
1025void
1026ip22serial_console_termios(struct console *con, char *options)
1027{
1028 int baud = 9600, bits = 8, cflag;
1029 int parity = 'n';
1030 int flow = 'n';
1031
1032 if (options)
1033 uart_parse_options(options, &baud, &parity, &bits, &flow);
1034
1035 cflag = CREAD | HUPCL | CLOCAL;
1036
1037 switch (baud) {
1038 case 150: cflag |= B150; break;
1039 case 300: cflag |= B300; break;
1040 case 600: cflag |= B600; break;
1041 case 1200: cflag |= B1200; break;
1042 case 2400: cflag |= B2400; break;
1043 case 4800: cflag |= B4800; break;
1044 case 9600: cflag |= B9600; break;
1045 case 19200: cflag |= B19200; break;
1046 case 38400: cflag |= B38400; break;
1047 default: baud = 9600; cflag |= B9600; break;
1048 }
1049
1050 con->cflag = cflag | CS8; /* 8N1 */
1051}
1052
1053static int __init ip22zilog_console_setup(struct console *con, char *options)
1054{
1055 struct uart_ip22zilog_port *up = &ip22zilog_port_table[con->index];
1056 unsigned long flags;
1057 int baud, brg;
1058
1059 printk("Console: ttyS%d (IP22-Zilog)\n", con->index);
1060
1061 /* Get firmware console settings. */
1062 ip22serial_console_termios(con, options);
1063
1064 /* Firmware console speed is limited to 150-->38400 baud so
1065 * this hackish cflag thing is OK.
1066 */
1067 switch (con->cflag & CBAUD) {
1068 case B150: baud = 150; break;
1069 case B300: baud = 300; break;
1070 case B600: baud = 600; break;
1071 case B1200: baud = 1200; break;
1072 case B2400: baud = 2400; break;
1073 case B4800: baud = 4800; break;
1074 default: case B9600: baud = 9600; break;
1075 case B19200: baud = 19200; break;
1076 case B38400: baud = 38400; break;
1077 };
1078
1079 brg = BPS_TO_BRG(baud, ZS_CLOCK / ZS_CLOCK_DIVISOR);
1080
1081 spin_lock_irqsave(&up->port.lock, flags);
1082
1083 up->curregs[R15] = BRKIE;
1084 ip22zilog_convert_to_zs(up, con->cflag, 0, brg);
1085
1086 __ip22zilog_startup(up);
1087
1088 spin_unlock_irqrestore(&up->port.lock, flags);
1089
1090 return 0;
1091}
1092
1093static struct uart_driver ip22zilog_reg;
1094
1095static struct console ip22zilog_console = {
1096 .name = "ttyS",
1097 .write = ip22zilog_console_write,
1098 .device = uart_console_device,
1099 .setup = ip22zilog_console_setup,
1100 .flags = CON_PRINTBUFFER,
1101 .index = -1,
1102 .data = &ip22zilog_reg,
1103};
1104#endif /* CONFIG_SERIAL_IP22_ZILOG_CONSOLE */
1105
1106static struct uart_driver ip22zilog_reg = {
1107 .owner = THIS_MODULE,
1108 .driver_name = "serial",
1109 .devfs_name = "tts/",
1110 .dev_name = "ttyS",
1111 .major = TTY_MAJOR,
1112 .minor = 64,
1113 .nr = NUM_CHANNELS,
1114#ifdef CONFIG_SERIAL_IP22_ZILOG_CONSOLE
1115 .cons = &ip22zilog_console,
1116#endif
1117};
1118
1119static void __init ip22zilog_prepare(void)
1120{
1121 struct uart_ip22zilog_port *up;
1122 struct zilog_layout *rp;
1123 int channel, chip;
1124
1125 /*
1126 * Temporary fix.
1127 */
1128 for (channel = 0; channel < NUM_CHANNELS; channel++)
1129 spin_lock_init(&ip22zilog_port_table[channel].port.lock);
1130
1131 ip22zilog_irq_chain = &ip22zilog_port_table[NUM_CHANNELS - 1];
1132 up = &ip22zilog_port_table[0];
1133 for (channel = NUM_CHANNELS - 1 ; channel > 0; channel--)
1134 up[channel].next = &up[channel - 1];
1135 up[channel].next = NULL;
1136
1137 for (chip = 0; chip < NUM_IP22ZILOG; chip++) {
1138 if (!ip22zilog_chip_regs[chip]) {
1139 ip22zilog_chip_regs[chip] = rp = get_zs(chip);
1140
1141 up[(chip * 2) + 0].port.membase = (char *) &rp->channelB;
1142 up[(chip * 2) + 1].port.membase = (char *) &rp->channelA;
1143
1144 /* In theory mapbase is the physical address ... */
1145 up[(chip * 2) + 0].port.mapbase =
1146 (unsigned long) ioremap((unsigned long) &rp->channelB, 8);
1147 up[(chip * 2) + 1].port.mapbase =
1148 (unsigned long) ioremap((unsigned long) &rp->channelA, 8);
1149 }
1150
1151 /* Channel A */
1152 up[(chip * 2) + 0].port.iotype = UPIO_MEM;
1153 up[(chip * 2) + 0].port.irq = zilog_irq;
1154 up[(chip * 2) + 0].port.uartclk = ZS_CLOCK;
1155 up[(chip * 2) + 0].port.fifosize = 1;
1156 up[(chip * 2) + 0].port.ops = &ip22zilog_pops;
1157 up[(chip * 2) + 0].port.type = PORT_IP22ZILOG;
1158 up[(chip * 2) + 0].port.flags = 0;
1159 up[(chip * 2) + 0].port.line = (chip * 2) + 0;
1160 up[(chip * 2) + 0].flags = 0;
1161
1162 /* Channel B */
1163 up[(chip * 2) + 1].port.iotype = UPIO_MEM;
1164 up[(chip * 2) + 1].port.irq = zilog_irq;
1165 up[(chip * 2) + 1].port.uartclk = ZS_CLOCK;
1166 up[(chip * 2) + 1].port.fifosize = 1;
1167 up[(chip * 2) + 1].port.ops = &ip22zilog_pops;
1168 up[(chip * 2) + 1].port.type = PORT_IP22ZILOG;
1169 up[(chip * 2) + 1].port.flags |= IP22ZILOG_FLAG_IS_CHANNEL_A;
1170 up[(chip * 2) + 1].port.line = (chip * 2) + 1;
1171 up[(chip * 2) + 1].flags = 0;
1172 }
1173}
1174
1175static void __init ip22zilog_init_hw(void)
1176{
1177 int i;
1178
1179 for (i = 0; i < NUM_CHANNELS; i++) {
1180 struct uart_ip22zilog_port *up = &ip22zilog_port_table[i];
1181 struct zilog_channel *channel = ZILOG_CHANNEL_FROM_PORT(&up->port);
1182 unsigned long flags;
1183 int baud, brg;
1184
1185 spin_lock_irqsave(&up->port.lock, flags);
1186
1187 if (ZS_IS_CHANNEL_A(up)) {
1188 write_zsreg(channel, R9, FHWRES);
1189 ZSDELAY_LONG();
1190 (void) read_zsreg(channel, R0);
1191 }
1192
1193 /* Normal serial TTY. */
1194 up->parity_mask = 0xff;
1195 up->curregs[R1] = EXT_INT_ENAB | INT_ALL_Rx | TxINT_ENAB;
1196 up->curregs[R4] = PAR_EVEN | X16CLK | SB1;
1197 up->curregs[R3] = RxENAB | Rx8;
1198 up->curregs[R5] = TxENAB | Tx8;
1199 up->curregs[R9] = NV | MIE;
1200 up->curregs[R10] = NRZ;
1201 up->curregs[R11] = TCBR | RCBR;
1202 baud = 9600;
1203 brg = BPS_TO_BRG(baud, ZS_CLOCK / ZS_CLOCK_DIVISOR);
1204 up->curregs[R12] = (brg & 0xff);
1205 up->curregs[R13] = (brg >> 8) & 0xff;
1206 up->curregs[R14] = BRENAB;
1207 __load_zsregs(channel, up->curregs);
1208 /* set master interrupt enable */
1209 write_zsreg(channel, R9, up->curregs[R9]);
1210
1211 spin_unlock_irqrestore(&up->port.lock, flags);
1212 }
1213}
1214
1215static int __init ip22zilog_ports_init(void)
1216{
1217 int ret;
1218
1219 printk(KERN_INFO "Serial: IP22 Zilog driver (%d chips).\n", NUM_IP22ZILOG);
1220
1221 ip22zilog_prepare();
1222
1223 if (request_irq(zilog_irq, ip22zilog_interrupt, 0,
1224 "IP22-Zilog", ip22zilog_irq_chain)) {
1225 panic("IP22-Zilog: Unable to register zs interrupt handler.\n");
1226 }
1227
1228 ip22zilog_init_hw();
1229
1230 ret = uart_register_driver(&ip22zilog_reg);
1231 if (ret == 0) {
1232 int i;
1233
1234 for (i = 0; i < NUM_CHANNELS; i++) {
1235 struct uart_ip22zilog_port *up = &ip22zilog_port_table[i];
1236
1237 uart_add_one_port(&ip22zilog_reg, &up->port);
1238 }
1239 }
1240
1241 return ret;
1242}
1243
1244static int __init ip22zilog_init(void)
1245{
1246 /* IP22 Zilog setup is hard coded, no probing to do. */
1247 ip22zilog_alloc_tables();
1248 ip22zilog_ports_init();
1249
1250 return 0;
1251}
1252
1253static void __exit ip22zilog_exit(void)
1254{
1255 int i;
1256
1257 for (i = 0; i < NUM_CHANNELS; i++) {
1258 struct uart_ip22zilog_port *up = &ip22zilog_port_table[i];
1259
1260 uart_remove_one_port(&ip22zilog_reg, &up->port);
1261 }
1262
1263 uart_unregister_driver(&ip22zilog_reg);
1264}
1265
1266module_init(ip22zilog_init);
1267module_exit(ip22zilog_exit);
1268
1269/* David wrote it but I'm to blame for the bugs ... */
1270MODULE_AUTHOR("Ralf Baechle <ralf@linux-mips.org>");
1271MODULE_DESCRIPTION("SGI Zilog serial port driver");
1272MODULE_LICENSE("GPL");