arch/arm/mach-omap1/usb.c

/*
 * Platform level USB initialization for FS USB OTG controller on omap1 and 24xx
 *
 * Copyright (C) 2004 Texas Instruments, Inc.
 *
 * This program is free software; you can redistribute it and/or modify
 * it under the terms of the GNU General Public License as published by
 * the Free Software Foundation; either version 2 of the License, or
 * (at your option) any later version.
 *
 * This program is distributed in the hope that it will be useful,
 * but WITHOUT ANY WARRANTY; without even the implied warranty of
 * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
 * GNU General Public License for more details.
 *
 * You should have received a copy of the GNU General Public License
 * along with this program; if not, write to the Free Software
 * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA  02111-1307  USA
 */

#include <linux/module.h>
#include <linux/kernel.h>
#include <linux/init.h>
#include <linux/platform_device.h>
#include <linux/io.h>

#include <asm/irq.h>

#include <plat/mux.h>
#include <plat/usb.h>

/* These routines should handle the standard chip-specific modes
 * for usb0/1/2 ports, covering basic mux and transceiver setup.
 *
 * Some board-*.c files will need to set up additional mux options,
 * like for suspend handling, vbus sensing, GPIOs, and the D+ pullup.
 */

/* TESTED ON:
 *  - 1611B H2 (with usb1 mini-AB) using standard Mini-B or OTG cables
 *  - 5912 OSK OHCI (with usb0 standard-A), standard A-to-B cables
 *  - 5912 OSK UDC, with *nonstandard* A-to-A cable
 *  - 1510 Innovator UDC with bundled usb0 cable
 *  - 1510 Innovator OHCI with bundled usb1/usb2 cable
 *  - 1510 Innovator OHCI with custom usb0 cable, feeding 5V VBUS
 *  - 1710 custom development board using alternate pin group
 *  - 1710 H3 (with usb1 mini-AB) using standard Mini-B or OTG cables
 */

#define INT_USB_IRQ_GEN		IH2_BASE + 20
#define INT_USB_IRQ_NISO	IH2_BASE + 30
#define INT_USB_IRQ_ISO		IH2_BASE + 29
#define INT_USB_IRQ_HGEN	INT_USB_HHC_1
#define INT_USB_IRQ_OTG		IH2_BASE + 8

#ifdef	CONFIG_USB_GADGET_OMAP

static struct resource udc_resources[] = {
	/* order is significant! */
	{		/* registers */
		.start		= UDC_BASE,
		.end		= UDC_BASE + 0xff,
		.flags		= IORESOURCE_MEM,
	}, {		/* general IRQ */
		.start		= INT_USB_IRQ_GEN,
		.flags		= IORESOURCE_IRQ,
	}, {		/* PIO IRQ */
		.start		= INT_USB_IRQ_NISO,
		.flags		= IORESOURCE_IRQ,
	}, {		/* SOF IRQ */
		.start		= INT_USB_IRQ_ISO,
		.flags		= IORESOURCE_IRQ,
	},
};

static u64 udc_dmamask = ~(u32)0;

static struct platform_device udc_device = {
	.name		= "omap_udc",
	.id		= -1,
	.dev = {
		.dma_mask		= &udc_dmamask,
		.coherent_dma_mask	= 0xffffffff,
	},
	.num_resources	= ARRAY_SIZE(udc_resources),
	.resource	= udc_resources,
};

static inline void udc_device_init(struct omap_usb_config *pdata)
{
	/* IRQ numbers for omap7xx */
	if(cpu_is_omap7xx()) {
		udc_resources[1].start = INT_7XX_USB_GENI;
		udc_resources[2].start = INT_7XX_USB_NON_ISO;
		udc_resources[3].start = INT_7XX_USB_ISO;
	}
	pdata->udc_device = &udc_device;
}

#else

static inline void udc_device_init(struct omap_usb_config *pdata)
{
}

#endif

#if	defined(CONFIG_USB_OHCI_HCD) || defined(CONFIG_USB_OHCI_HCD_MODULE)

/* The dmamask must be set for OHCI to work */
static u64 ohci_dmamask = ~(u32)0;

static struct resource ohci_resources[] = {
	{
		.start	= OMAP_OHCI_BASE,
		.end	= OMAP_OHCI_BASE + 0xff,
		.flags	= IORESOURCE_MEM,
	},
	{
		.start	= INT_USB_IRQ_HGEN,
		.flags	= IORESOURCE_IRQ,
	},
};

static struct platform_device ohci_device = {
	.name			= "ohci",
	.id			= -1,
	.dev = {
		.dma_mask		= &ohci_dmamask,
		.coherent_dma_mask	= 0xffffffff,
	},
	.num_resources	= ARRAY_SIZE(ohci_resources),
	.resource		= ohci_resources,
};

static inline void ohci_device_init(struct omap_usb_config *pdata)
{
	if (cpu_is_omap7xx())
		ohci_resources[1].start = INT_7XX_USB_HHC_1;
	pdata->ohci_device = &ohci_device;
}

#else

static inline void ohci_device_init(struct omap_usb_config *pdata)
{
}

#endif

#if	defined(CONFIG_USB_OTG) && defined(CONFIG_ARCH_OMAP_OTG)

static struct resource otg_resources[] = {
	/* order is significant! */
	{
		.start		= OTG_BASE,
		.end		= OTG_BASE + 0xff,
		.flags		= IORESOURCE_MEM,
	}, {
		.start		= INT_USB_IRQ_OTG,
		.flags		= IORESOURCE_IRQ,
	},
};

static struct platform_device otg_device = {
	.name		= "omap_otg",
	.id		= -1,
	.num_resources	= ARRAY_SIZE(otg_resources),
	.resource	= otg_resources,
};

static inline void otg_device_init(struct omap_usb_config *pdata)
{
	if (cpu_is_omap7xx())
		otg_resources[1].start = INT_7XX_USB_OTG;
	pdata->otg_device = &otg_device;
}

#else

static inline void otg_device_init(struct omap_usb_config *pdata)
{
}

#endif

u32 __init omap1_usb0_init(unsigned nwires, unsigned is_device)
{
	u32	syscon1 = 0;

	if (nwires == 0) {
		if (!cpu_is_omap15xx()) {
			u32 l;

			/* pulldown D+/D- */
			l = omap_readl(USB_TRANSCEIVER_CTRL);
			l &= ~(3 << 1);
			omap_writel(l, USB_TRANSCEIVER_CTRL);
		}
		return 0;
	}

	if (is_device) {
		if (cpu_is_omap7xx()) {
			omap_cfg_reg(AA17_7XX_USB_DM);
			omap_cfg_reg(W16_7XX_USB_PU_EN);
			omap_cfg_reg(W17_7XX_USB_VBUSI);
			omap_cfg_reg(W18_7XX_USB_DMCK_OUT);
			omap_cfg_reg(W19_7XX_USB_DCRST);
		} else
			omap_cfg_reg(W4_USB_PUEN);
	}

	if (nwires == 2) {
		u32 l;

		// omap_cfg_reg(P9_USB_DP);
		// omap_cfg_reg(R8_USB_DM);

		if (cpu_is_omap15xx()) {
			/* This works on 1510-Innovator */
			return 0;
		}

		/* NOTES:
		 *  - peripheral should configure VBUS detection!
		 *  - only peripherals may use the internal D+/D- pulldowns
		 *  - OTG support on this port not yet written
		 */

		/* Don't do this for omap7xx -- it causes USB to not work correctly */
		if (!cpu_is_omap7xx()) {
			l = omap_readl(USB_TRANSCEIVER_CTRL);
			l &= ~(7 << 4);
			if (!is_device)
				l |= (3 << 1);
			omap_writel(l, USB_TRANSCEIVER_CTRL);
		}

		return 3 << 16;
	}

	/* alternate pin config, external transceiver */
	if (cpu_is_omap15xx()) {
		printk(KERN_ERR "no usb0 alt pin config on 15xx\n");
		return 0;
	}

	omap_cfg_reg(V6_USB0_TXD);
	omap_cfg_reg(W9_USB0_TXEN);
	omap_cfg_reg(W5_USB0_SE0);
	if (nwires != 3)
		omap_cfg_reg(Y5_USB0_RCV);

	/* NOTE:  SPEED and SUSP aren't configured here.  OTG hosts
	 * may be able to use I2C requests to set those bits along
	 * with VBUS switching and overcurrent detection.
	 */

	if (nwires != 6) {
		u32 l;

		l = omap_readl(USB_TRANSCEIVER_CTRL);
		l &= ~CONF_USB2_UNI_R;
		omap_writel(l, USB_TRANSCEIVER_CTRL);
	}

	switch (nwires) {
	case 3:
		syscon1 = 2;
		break;
	case 4:
		syscon1 = 1;
		break;
	case 6:
		syscon1 = 3;
		{
			u32 l;

			omap_cfg_reg(AA9_USB0_VP);
			omap_cfg_reg(R9_USB0_VM);
			l = omap_readl(USB_TRANSCEIVER_CTRL);
			l |= CONF_USB2_UNI_R;
			omap_writel(l, USB_TRANSCEIVER_CTRL);
		}
		break;
	default:
		printk(KERN_ERR "illegal usb%d %d-wire transceiver\n",
			0, nwires);
	}

	return syscon1 << 16;
}

u32 __init omap1_usb1_init(unsigned nwires)
{
	u32	syscon1 = 0;

	if (!cpu_is_omap15xx() && nwires != 6) {
		u32 l;

		l = omap_readl(USB_TRANSCEIVER_CTRL);
		l &= ~CONF_USB1_UNI_R;
		omap_writel(l, USB_TRANSCEIVER_CTRL);
	}
	if (nwires == 0)
		return 0;

	/* external transceiver */
	omap_cfg_reg(USB1_TXD);
	omap_cfg_reg(USB1_TXEN);
	if (nwires != 3)
		omap_cfg_reg(USB1_RCV);

	if (cpu_is_omap15xx()) {
		omap_cfg_reg(USB1_SEO);
		omap_cfg_reg(USB1_SPEED);
		// SUSP
	} else if (cpu_is_omap1610() || cpu_is_omap5912()) {
		omap_cfg_reg(W13_1610_USB1_SE0);
		omap_cfg_reg(R13_1610_USB1_SPEED);
		// SUSP
	} else if (cpu_is_omap1710()) {
		omap_cfg_reg(R13_1710_USB1_SE0);
		// SUSP
	} else {
		pr_debug("usb%d cpu unrecognized\n", 1);
		return 0;
	}

	switch (nwires) {
	case 2:
		goto bad;
	case 3:
		syscon1 = 2;
		break;
	case 4:
		syscon1 = 1;
		break;
	case 6:
		syscon1 = 3;
		omap_cfg_reg(USB1_VP);
		omap_cfg_reg(USB1_VM);
		if (!cpu_is_omap15xx()) {
			u32 l;

			l = omap_readl(USB_TRANSCEIVER_CTRL);
			l |= CONF_USB1_UNI_R;
			omap_writel(l, USB_TRANSCEIVER_CTRL);
		}
		break;
	default:
bad:
		printk(KERN_ERR "illegal usb%d %d-wire transceiver\n",
			1, nwires);
	}

	return syscon1 << 20;
}

u32 __init omap1_usb2_init(unsigned nwires, unsigned alt_pingroup)
{
	u32	syscon1 = 0;

	/* NOTE omap1 erratum: must leave USB2_UNI_R set if usb0 in use */
	if (alt_pingroup || nwires == 0)
		return 0;

	if (!cpu_is_omap15xx() && nwires != 6) {
		u32 l;

		l = omap_readl(USB_TRANSCEIVER_CTRL);
		l &= ~CONF_USB2_UNI_R;
		omap_writel(l, USB_TRANSCEIVER_CTRL);
	}

	/* external transceiver */
	if (cpu_is_omap15xx()) {
		omap_cfg_reg(USB2_TXD);
		omap_cfg_reg(USB2_TXEN);
		omap_cfg_reg(USB2_SEO);
		if (nwires != 3)
			omap_cfg_reg(USB2_RCV);
		/* there is no USB2_SPEED */
	} else if (cpu_is_omap16xx()) {
		omap_cfg_reg(V6_USB2_TXD);
		omap_cfg_reg(W9_USB2_TXEN);
		omap_cfg_reg(W5_USB2_SE0);
		if (nwires != 3)
			omap_cfg_reg(Y5_USB2_RCV);
		// FIXME omap_cfg_reg(USB2_SPEED);
	} else {
		pr_debug("usb%d cpu unrecognized\n", 1);
		return 0;
	}

	// omap_cfg_reg(USB2_SUSP);

	switch (nwires) {
	case 2:
		goto bad;
	case 3:
		syscon1 = 2;
		break;
	case 4:
		syscon1 = 1;
		break;
	case 5:
		goto bad;
	case 6:
		syscon1 = 3;
		if (cpu_is_omap15xx()) {
			omap_cfg_reg(USB2_VP);
			omap_cfg_reg(USB2_VM);
		} else {
			u32 l;

			omap_cfg_reg(AA9_USB2_VP);
			omap_cfg_reg(R9_USB2_VM);
			l = omap_readl(USB_TRANSCEIVER_CTRL);
			l |= CONF_USB2_UNI_R;
			omap_writel(l, USB_TRANSCEIVER_CTRL);
		}
		break;
	default:
bad:
		printk(KERN_ERR "illegal usb%d %d-wire transceiver\n",
			2, nwires);
	}

	return syscon1 << 24;
}

#ifdef	CONFIG_ARCH_OMAP15XX

/* ULPD_DPLL_CTRL */
#define DPLL_IOB		(1 << 13)
#define DPLL_PLL_ENABLE		(1 << 4)
#define DPLL_LOCK		(1 << 0)

/* ULPD_APLL_CTRL */
#define APLL_NDPLL_SWITCH	(1 << 0)

static void __init omap_1510_usb_init(struct omap_usb_config *config)
{
	unsigned int val;
	u16 w;

	config->usb0_init(config->pins[0], is_usb0_device(config));
	config->usb1_init(config->pins[1]);
	config->usb2_init(config->pins[2], 0);

	val = omap_readl(MOD_CONF_CTRL_0) & ~(0x3f << 1);
	val |= (config->hmc_mode << 1);
	omap_writel(val, MOD_CONF_CTRL_0);

	printk("USB: hmc %d", config->hmc_mode);
	if (config->pins[0])
		printk(", usb0 %d wires%s", config->pins[0],
			is_usb0_device(config) ? " (dev)" : "");
	if (config->pins[1])
		printk(", usb1 %d wires", config->pins[1]);
	if (config->pins[2])
		printk(", usb2 %d wires", config->pins[2]);
	printk("\n");

	/* use DPLL for 48 MHz function clock */
	pr_debug("APLL %04x DPLL %04x REQ %04x\n", omap_readw(ULPD_APLL_CTRL),
			omap_readw(ULPD_DPLL_CTRL), omap_readw(ULPD_SOFT_REQ));

	w = omap_readw(ULPD_APLL_CTRL);
	w &= ~APLL_NDPLL_SWITCH;
	omap_writew(w, ULPD_APLL_CTRL);

	w = omap_readw(ULPD_DPLL_CTRL);
	w |= DPLL_IOB | DPLL_PLL_ENABLE;
	omap_writew(w, ULPD_DPLL_CTRL);

	w = omap_readw(ULPD_SOFT_REQ);
	w |= SOFT_UDC_REQ | SOFT_DPLL_REQ;
	omap_writew(w, ULPD_SOFT_REQ);

	while (!(omap_readw(ULPD_DPLL_CTRL) & DPLL_LOCK))
		cpu_relax();

#ifdef	CONFIG_USB_GADGET_OMAP
	if (config->register_dev) {
		int status;

		udc_device.dev.platform_data = config;
		status = platform_device_register(&udc_device);
		if (status)
			pr_debug("can't register UDC device, %d\n", status);
		/* udc driver gates 48MHz by D+ pullup */
	}
#endif

#if	defined(CONFIG_USB_OHCI_HCD) || defined(CONFIG_USB_OHCI_HCD_MODULE)
	if (config->register_host) {
		int status;

		ohci_device.dev.platform_data = config;
		status = platform_device_register(&ohci_device);
		if (status)
			pr_debug("can't register OHCI device, %d\n", status);
		/* hcd explicitly gates 48MHz */
	}
#endif
}

#else
static inline void omap_1510_usb_init(struct omap_usb_config *config) {}
#endif

void __init omap1_usb_init(struct omap_usb_config *pdata)
{
	pdata->usb0_init = omap1_usb0_init;
	pdata->usb1_init = omap1_usb1_init;
	pdata->usb2_init = omap1_usb2_init;
	udc_device_init(pdata);
	ohci_device_init(pdata);
	otg_device_init(pdata);

	if (cpu_is_omap7xx() || cpu_is_omap16xx())
		omap_otg_init(pdata);
	else if (cpu_is_omap15xx())
		omap_1510_usb_init(pdata);
	else
		printk(KERN_ERR "USB: No init for your chip yet\n");
}