| #!/bin/sh |
| |
| TST_TOTAL=1 |
| TCID="network_settings" |
| . test_net.sh |
| |
| # Network Test Parameters |
| # |
| # ---***** THESE MUST BE SET FOR CORRECT OPERATION *****--- |
| |
| # Management Link |
| export RHOST=${RHOST:-""} |
| export PASSWD=${PASSWD:-""} |
| |
| # Warning: |
| # Make sure to set valid interface names and IP addresses below. |
| # 'networktests.sh' expects that IP addresses are already added to interface. |
| # |
| # Please note, that for 'networktests.sh' tests, management link and |
| # test link can be the same. |
| |
| # Test Links |
| # Set names for test interfaces, e.g. "eth0 eth1" |
| export LHOST_IFACES=${LHOST_IFACES:-"eth0"} |
| export RHOST_IFACES=${RHOST_IFACES:-"eth0"} |
| |
| # Set corresponding HW addresses, e.g. "00:00:00:00:00:01 00:00:00:00:00:02" |
| export LHOST_HWADDRS=${LHOST_HWADDRS:-"$(tst_get_hwaddrs lhost)"} |
| export RHOST_HWADDRS=${RHOST_HWADDRS:-"$(tst_get_hwaddrs rhost)"} |
| |
| # Set first three octets of the network address, default is '10.0.0' |
| export IPV4_NETWORK=${IPV4_NETWORK:-"10.0.0"} |
| # Set local host last octet, default is '2' |
| export LHOST_IPV4_HOST=${LHOST_IPV4_HOST:-"2"} |
| # Set remote host last octet, default is '1' |
| export RHOST_IPV4_HOST=${RHOST_IPV4_HOST:-"1"} |
| # Set the reverse of IPV4_NETWORK |
| export IPV4_NETWORK_REVERSE=${IPV4_NETWORK_REVERSE:-"0.0.10"} |
| # Set first three octets of the network address, default is 'fd00:1:1:1' |
| export IPV6_NETWORK=${IPV6_NETWORK:-"fd00:1:1:1"} |
| # Set local host last octet, default is '2' |
| export LHOST_IPV6_HOST=${LHOST_IPV6_HOST:-":2"} |
| # Set remote host last octet, default is '1' |
| export RHOST_IPV6_HOST=${RHOST_IPV6_HOST:-":1"} |
| |
| export HTTP_DOWNLOAD_DIR=${HTTP_DOWNLOAD_DIR:-""} |
| export FTP_DOWNLOAD_DIR=${FTP_DOWNLOAD_DIR:-""} |
| export FTP_UPLOAD_DIR=${FTP_UPLOAD_DIR:-""} |
| export FTP_UPLOAD_URLDIR=${FTP_UPLOAD_URLDIR:-""} |
| |
| # More information about network parameters can be found |
| # in the following document: testcases/network/stress/README |
| |
| # ---***************************************************--- |
| |
| # Don't use it in new tests, use tst_rhost_run() from test_net.sh instead. |
| export LTP_RSH=${LTP_RSH:-"rsh -n"} |
| |
| export TMPDIR=/tmp/netpan-$$ |
| mkdir -p $TMPDIR |
| CMDFILE=${TMPDIR}/network.tests |
| VERBOSE="no" |
| |
| export LTPROOT=${LTPROOT:-"$PWD"} |
| echo $LTPROOT | grep testscripts > /dev/null 2>&1 |
| if [ $? -eq 0 ]; then |
| cd .. |
| export LTPROOT=${PWD} |
| fi |
| |
| export PATH="${PATH}:${LTPROOT}/testcases/bin" |
| |
| # Reset variables. |
| # Don't break the tests which are using 'testcases/lib/cmdlib.sh' |
| export TCID= |
| export TST_LIB_LOADED= |