blob: 6a0c68de4c0784509d463d3dd404fbf54daddaee [file] [log] [blame]
/*
* (C) Copyright 2001
* Wolfgang Denk, DENX Software Engineering, wd@denx.de.
*
* (C) Copyright 2002
* Gregory E. Allen, gallen@arlut.utexas.edu
* Matthew E. Karger, karger@arlut.utexas.edu
* Applied Research Laboratories, The University of Texas at Austin
*
* See file CREDITS for list of people who contributed to this
* project.
*
* This program is free software; you can redistribute it and/or
* modify it under the terms of the GNU General Public License as
* published by the Free Software Foundation; either version 2 of
* the License, or (at your option) any later version.
*
* This program is distributed in the hope that it will be useful,
* but WITHOUT ANY WARRANTY; without even the implied warranty of
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
* GNU General Public License for more details.
*
* You should have received a copy of the GNU General Public License
* along with this program; if not, write to the Free Software
* Foundation, Inc., 59 Temple Place, Suite 330, Boston,
* MA 02111-1307 USA
*/
/*
*
* Configuration settings for the utx8245 board.
*
*/
/* ------------------------------------------------------------------------- */
/*
* board/config.h - configuration options, board specific
*/
#ifndef __CONFIG_H
#define __CONFIG_H
/*
* High Level Configuration Options
* (easy to change)
*/
#define CONFIG_MPC824X 1
#define CONFIG_MPC8245 1
#define CONFIG_UTX8245 1
#define DEBUG 1
#define CONFIG_IDENT_STRING " [UTX5] "
#define CONFIG_CONS_INDEX 1
#define CONFIG_BAUDRATE 57600
#define CONFIG_SYS_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200 }
#define CONFIG_BOOTDELAY 2
#define CONFIG_AUTOBOOT_PROMPT "autoboot in %d seconds\n", bootdelay
#define CONFIG_BOOTCOMMAND "run nfsboot" /* autoboot command */
#define CONFIG_BOOTARGS "root=/dev/ram console=ttyS0,57600" /* RAMdisk */
#define CONFIG_ETHADDR 00:AA:00:14:00:05 /* UTX5 */
#define CONFIG_SERVERIP 10.8.17.105 /* Spree */
#define CONFIG_SYS_TFTP_LOADADDR 10000
#define CONFIG_EXTRA_ENV_SETTINGS \
"kernel_addr=FFA00000\0" \
"ramdisk_addr=FF800000\0" \
"u-boot_startaddr=FFB00000\0" \
"u-boot_endaddr=FFB2FFFF\0" \
"nfsargs=setenv bootargs console=ttyS0,${baudrate} root=/dev/nfs rw \
nfsroot=${nfsrootip}:${rootpath} ip=dhcp\0" \
"ramargs=setenv bootargs console=ttyS0,${baudrate} root=/dev/ram0\0" \
"smargs=setenv bootargs console=ttyS0,${baudrate} root=/dev/mtdblock1 ro\0" \
"fwargs=setenv bootargs console=ttyS0,${baudrate} root=/dev/sda2 ro\0" \
"nfsboot=run nfsargs;bootm ${kernel_addr}\0" \
"ramboot=run ramargs;bootm ${kernel_addr} ${ramdisk_addr}\0" \
"smboot=run smargs;bootm ${kernel_addr} ${ramdisk_addr}\0" \
"fwboot=run fwargs;bootm ${kernel_addr} ${ramdisk_addr}\0" \
"update_u-boot=tftp ${loadaddr} /bdi2000/u-boot.bin;protect off \
${u-boot_startaddr} ${u-boot_endaddr};era ${u-boot_startaddr} \
${u-boot_endaddr};cp.b ${loadaddr} ${u-boot_startaddr} ${filesize};\
protect on ${u-boot_startaddr} ${u-boot_endaddr}"
#define CONFIG_ENV_OVERWRITE
/*
* BOOTP options
*/
#define CONFIG_BOOTP_BOOTFILESIZE
#define CONFIG_BOOTP_BOOTPATH
#define CONFIG_BOOTP_GATEWAY
#define CONFIG_BOOTP_HOSTNAME
/*
* Command line configuration.
*/
#include <config_cmd_default.h>
#define CONFIG_CMD_BDI
#define CONFIG_CMD_PCI
#define CONFIG_CMD_FLASH
#define CONFIG_CMD_MEMORY
#define CONFIG_CMD_SAVEENV
#define CONFIG_CMD_CONSOLE
#define CONFIG_CMD_LOADS
#define CONFIG_CMD_LOADB
#define CONFIG_CMD_IMI
#define CONFIG_CMD_CACHE
#define CONFIG_CMD_REGINFO
#define CONFIG_CMD_NET
#define CONFIG_CMD_DHCP
#define CONFIG_CMD_I2C
#define CONFIG_CMD_DATE
/*
* Miscellaneous configurable options
*/
#define CONFIG_SYS_LONGHELP /* undef to save memory */
#define CONFIG_SYS_PROMPT "=> " /* Monitor Command Prompt */
#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */
/* Print Buffer Size */
#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE + sizeof(CONFIG_SYS_PROMPT) + 16)
#define CONFIG_SYS_MAXARGS 16 /* max number of command args */
#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */
#define CONFIG_SYS_LOAD_ADDR 0x00100000 /* Default load address */
/*-----------------------------------------------------------------------
* PCI configuration
*-----------------------------------------------------------------------
*/
#define CONFIG_PCI /* include pci support */
#undef CONFIG_PCI_PNP
#define CONFIG_PCI_SCAN_SHOW
#define CONFIG_NET_MULTI
#define CONFIG_EEPRO100
#define CONFIG_SYS_RX_ETH_BUFFER 8 /* use 8 rx buffer on eepro100 */
#define CONFIG_EEPRO100_SROM_WRITE
#define PCI_ENET0_IOADDR 0xF0000000
#define PCI_ENET0_MEMADDR 0xF0000000
#define PCI_FIREWIRE_IOADDR 0xF1000000
#define PCI_FIREWIRE_MEMADDR 0xF1000000
/*
#define PCI_ENET0_IOADDR 0xFE000000
#define PCI_ENET0_MEMADDR 0x80000000
#define PCI_FIREWIRE_IOADDR 0x81000000
#define PCI_FIREWIRE_MEMADDR 0x81000000
*/
/*-----------------------------------------------------------------------
* Start addresses for the final memory configuration
* (Set up by the startup code)
* Please note that CONFIG_SYS_SDRAM_BASE _must_ start at 0
*/
#define CONFIG_SYS_SDRAM_BASE 0x00000000
#define CONFIG_SYS_MAX_RAM_SIZE 0x10000000 /* 256MB */
/*#define CONFIG_SYS_VERY_BIG_RAM 1 */
/* FLASH_BASE is FF800000, with 4MB on RCS0, but the reset vector
* is actually located at FFF00100. Therefore, U-Boot is
* physically located at 0xFFB0_0000, but is also mirrored at
* 0xFFF0_0000.
*/
#define CONFIG_SYS_RESET_ADDRESS 0xFFF00100
#define CONFIG_SYS_EUMB_ADDR 0xFC000000
#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE
#define CONFIG_SYS_MONITOR_LEN (256 << 10) /* Reserve 256 kB for Monitor */
#define CONFIG_SYS_MALLOC_LEN (128 << 10) /* Reserve 128 kB for malloc() */
/*#define CONFIG_SYS_DRAM_TEST 1 */
#define CONFIG_SYS_MEMTEST_START 0x00003000 /* memtest works on 0...256 MB */
#define CONFIG_SYS_MEMTEST_END 0x0ff8ffa7 /* in SDRAM, skips exception */
/* vectors and U-Boot */
/*--------------------------------------------------------------------
* Definitions for initial stack pointer and data area
*------------------------------------------------------------------*/
#define CONFIG_SYS_INIT_DATA_SIZE 128 /* Size in bytes reserved for */
/* initial data */
#define CONFIG_SYS_INIT_RAM_ADDR 0x40000000
#define CONFIG_SYS_INIT_RAM_END 0x1000
#define CONFIG_SYS_INIT_DATA_OFFSET (CONFIG_SYS_INIT_RAM_END - CONFIG_SYS_INIT_DATA_SIZE)
#define CONFIG_SYS_GBL_DATA_SIZE 128
#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_END - CONFIG_SYS_GBL_DATA_SIZE)
/*--------------------------------------------------------------------
* NS16550 Configuration
*------------------------------------------------------------------*/
#define CONFIG_SYS_NS16550
#define CONFIG_SYS_NS16550_SERIAL
#define CONFIG_SYS_NS16550_REG_SIZE 1
#if (CONFIG_CONS_INDEX == 1 || CONFIG_CONS_INDEX == 2)
# define CONFIG_SYS_NS16550_CLK get_bus_freq(0)
#else
# define CONFIG_SYS_NS16550_CLK 33000000
#endif
#define CONFIG_SYS_NS16550_COM1 (CONFIG_SYS_EUMB_ADDR + 0x4500)
#define CONFIG_SYS_NS16550_COM2 (CONFIG_SYS_EUMB_ADDR + 0x4600)
#define CONFIG_SYS_NS16550_COM3 0xFF000000
#define CONFIG_SYS_NS16550_COM4 0xFF000008
/*--------------------------------------------------------------------
* Low Level Configuration Settings
* (address mappings, register initial values, etc.)
* You should know what you are doing if you make changes here.
* For the detail description refer to the MPC8240 user's manual.
*------------------------------------------------------------------*/
#define CONFIG_SYS_CLK_FREQ 33000000
#define CONFIG_SYS_HZ 1000
/*#define CONFIG_SYS_ETH_DEV_FN 0x7800 */
/*#define CONFIG_SYS_ETH_IOBASE 0x00104000 */
/*--------------------------------------------------------------------
* I2C Configuration
*------------------------------------------------------------------*/
#if 1
#define CONFIG_HARD_I2C 1 /* To enable I2C support */
#undef CONFIG_SOFT_I2C /* I2C bit-banged */
#define CONFIG_SYS_I2C_SPEED 400000 /* I2C speed and slave address */
#define CONFIG_SYS_I2C_SLAVE 0x7F
#endif
#define CONFIG_RTC_PCF8563 1 /* enable I2C support for */
/* Philips PCF8563 RTC */
#define CONFIG_SYS_I2C_RTC_ADDR 0x51 /* Philips PCF8563 RTC address */
/*--------------------------------------------------------------------
* Memory Control Configuration Register values
* - see sec. 4.12 of MPC8245 UM
*------------------------------------------------------------------*/
/**** MCCR1 ****/
#define CONFIG_SYS_ROMNAL 0
#define CONFIG_SYS_ROMFAL 10 /* (tacc=70ns)*mem_freq - 2,
mem_freq = 100MHz */
#define CONFIG_SYS_BANK7_ROW 0 /* SDRAM bank 7-0 row address */
#define CONFIG_SYS_BANK6_ROW 0 /* bit count */
#define CONFIG_SYS_BANK5_ROW 0
#define CONFIG_SYS_BANK4_ROW 0
#define CONFIG_SYS_BANK3_ROW 0
#define CONFIG_SYS_BANK2_ROW 0
#define CONFIG_SYS_BANK1_ROW 2
#define CONFIG_SYS_BANK0_ROW 2
/**** MCCR2, refresh interval clock cycles ****/
#define CONFIG_SYS_REFINT 480 /* 33 MHz SDRAM clock was 480 */
/* Burst To Precharge. Bits of this value go to MCCR3 and MCCR4. */
#define CONFIG_SYS_BSTOPRE 1023 /* burst to precharge[0..9], */
/* sets open page interval */
/**** MCCR3 ****/
#define CONFIG_SYS_REFREC 7 /* Refresh to activate interval, trc */
/**** MCCR4 ****/
#define CONFIG_SYS_PRETOACT 2 /* trp */
#define CONFIG_SYS_ACTTOPRE 7 /* trcd + (burst length - 1) + trdl */
#define CONFIG_SYS_SDMODE_CAS_LAT 3 /* SDMODE CAS latancy */
#define CONFIG_SYS_SDMODE_WRAP 0 /* SDMODE wrap type, sequential */
#define CONFIG_SYS_ACTORW 2 /* trcd min */
#define CONFIG_SYS_DBUS_SIZE2 1 /* set for 8-bit RCS1, clear for 32,64 */
#define CONFIG_SYS_REGISTERD_TYPE_BUFFER 1
#define CONFIG_SYS_EXTROM 0 /* we don't need extended ROM space */
#define CONFIG_SYS_REGDIMM 0
/* calculate according to formula in sec. 6-22 of 8245 UM */
#define CONFIG_SYS_PGMAX 50 /* how long the 8245 retains the */
/* currently accessed page in memory */
/* was 45 */
#define CONFIG_SYS_SDRAM_DSCD 0x20 /* SDRAM data in sample clock delay - note */
/* bits 7,6, and 3-0 MUST be 0 */
#if 0
#define CONFIG_SYS_DLL_MAX_DELAY 0x04
#else
#define CONFIG_SYS_DLL_MAX_DELAY 0
#endif
#if 0 /* need for 33MHz SDRAM */
#define CONFIG_SYS_DLL_EXTEND 0x80
#else
#define CONFIG_SYS_DLL_EXTEND 0
#endif
#define CONFIG_SYS_PCI_HOLD_DEL 0x20
/* Memory bank settings.
* Only bits 20-29 are actually used from these values to set the
* start/end addresses. The upper two bits will always be 0, and the lower
* 20 bits will be 0x00000 for a start address, or 0xfffff for an end
* address. Refer to the MPC8245 user manual.
*/
#define CONFIG_SYS_BANK0_START 0x00000000
#define CONFIG_SYS_BANK0_END (CONFIG_SYS_MAX_RAM_SIZE/2 - 1)
#define CONFIG_SYS_BANK0_ENABLE 1
#define CONFIG_SYS_BANK1_START CONFIG_SYS_MAX_RAM_SIZE/2
#define CONFIG_SYS_BANK1_END (CONFIG_SYS_MAX_RAM_SIZE - 1)
#define CONFIG_SYS_BANK1_ENABLE 1
#define CONFIG_SYS_BANK2_START 0x3ff00000 /* not available in this design */
#define CONFIG_SYS_BANK2_END 0x3fffffff
#define CONFIG_SYS_BANK2_ENABLE 0
#define CONFIG_SYS_BANK3_START 0x3ff00000
#define CONFIG_SYS_BANK3_END 0x3fffffff
#define CONFIG_SYS_BANK3_ENABLE 0
#define CONFIG_SYS_BANK4_START 0x3ff00000
#define CONFIG_SYS_BANK4_END 0x3fffffff
#define CONFIG_SYS_BANK4_ENABLE 0
#define CONFIG_SYS_BANK5_START 0x3ff00000
#define CONFIG_SYS_BANK5_END 0x3fffffff
#define CONFIG_SYS_BANK5_ENABLE 0
#define CONFIG_SYS_BANK6_START 0x3ff00000
#define CONFIG_SYS_BANK6_END 0x3fffffff
#define CONFIG_SYS_BANK6_ENABLE 0
#define CONFIG_SYS_BANK7_START 0x3ff00000
#define CONFIG_SYS_BANK7_END 0x3fffffff
#define CONFIG_SYS_BANK7_ENABLE 0
/*--------------------------------------------------------------------*/
/* 4.4 - Output Driver Control Register */
/*--------------------------------------------------------------------*/
#define CONFIG_SYS_ODCR 0xe5
/*--------------------------------------------------------------------*/
/* 4.8 - Error Handling Registers */
/*-------------------------------CONFIG_SYS_SDMODE_BURSTLEN-------------------------------------*/
#define CONFIG_SYS_ERRENR1 0x11 /* enable SDRAM refresh overflow error */
/* SDRAM 0-256 MB */
#define CONFIG_SYS_IBAT0L (CONFIG_SYS_SDRAM_BASE | BATL_PP_10 | BATL_MEMCOHERENCE)
/*#define CONFIG_SYS_IBAT0L (CONFIG_SYS_SDRAM_BASE | BATL_PP_10 | BATL_CACHEINHIBIT) */
#define CONFIG_SYS_IBAT0U (CONFIG_SYS_SDRAM_BASE | BATU_BL_256M | BATU_VS | BATU_VP)
/* stack in dcache */
#define CONFIG_SYS_IBAT1L (CONFIG_SYS_INIT_RAM_ADDR | BATL_PP_10 | BATL_MEMCOHERENCE)
#define CONFIG_SYS_IBAT1U (CONFIG_SYS_INIT_RAM_ADDR | BATU_BL_128K | BATU_VS | BATU_VP)
#define CONFIG_SYS_IBAT2L (CONFIG_SYS_SDRAM_BASE + 0x10000000 | BATL_PP_10 | BATL_MEMCOHERENCE)
#define CONFIG_SYS_IBAT2U (CONFIG_SYS_SDRAM_BASE + 0x10000000| BATU_BL_256M | BATU_VS | BATU_VP)
/* PCI memory */
/*#define CONFIG_SYS_IBAT2L (0x80000000 | BATL_PP_10 | BATL_CACHEINHIBIT) */
/*#define CONFIG_SYS_IBAT2U (0x80000000 | BATU_BL_256M | BATU_VS | BATU_VP) */
/*Flash, config addrs, etc. */
#define CONFIG_SYS_IBAT3L (0xF0000000 | BATL_PP_10 | BATL_CACHEINHIBIT)
#define CONFIG_SYS_IBAT3U (0xF0000000 | BATU_BL_256M | BATU_VS | BATU_VP)
#define CONFIG_SYS_DBAT0L CONFIG_SYS_IBAT0L
#define CONFIG_SYS_DBAT0U CONFIG_SYS_IBAT0U
#define CONFIG_SYS_DBAT1L CONFIG_SYS_IBAT1L
#define CONFIG_SYS_DBAT1U CONFIG_SYS_IBAT1U
#define CONFIG_SYS_DBAT2L CONFIG_SYS_IBAT2L
#define CONFIG_SYS_DBAT2U CONFIG_SYS_IBAT2U
#define CONFIG_SYS_DBAT3L CONFIG_SYS_IBAT3L
#define CONFIG_SYS_DBAT3U CONFIG_SYS_IBAT3U
/*
* For booting Linux, the board info and command line data
* have to be in the first 8 MB of memory, since this is
* the maximum mapped by the Linux kernel during initialization.
*/
#define CONFIG_SYS_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */
/*-----------------------------------------------------------------------
* FLASH organization
*----------------------------------------------------------------------*/
#define CONFIG_SYS_FLASH_BASE 0xFF800000
#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* Max number of flash banks */
/* NOTE: environment is not EMBEDDED in the u-boot code.
It's stored in flash in its own separate sector. */
#define CONFIG_ENV_IS_IN_FLASH 1
#if 1 /* AMD AM29LV033C */
#define CONFIG_SYS_MAX_FLASH_SECT 64 /* Max number of sectors in one bank */
#define CONFIG_ENV_ADDR 0xFFBF0000 /* flash sector SA63 */
#define CONFIG_ENV_SECT_SIZE (64*1024) /* Size of the Environment Sector */
#else /* AMD AM29LV116D */
#define CONFIG_SYS_MAX_FLASH_SECT 35 /* Max number of sectors in one bank */
#define CONFIG_ENV_ADDR 0xFF9FA000 /* flash sector SA33 */
#define CONFIG_ENV_SECT_SIZE (8*1024) /* Size of the Environment Sector */
#endif /* #if */
#define CONFIG_ENV_SIZE CONFIG_ENV_SECT_SIZE /* Size of the Environment */
#define CONFIG_ENV_OFFSET 0 /* starting right at the beginning */
#define CONFIG_SYS_FLASH_ERASE_TOUT 120000 /* Timeout for Flash Erase (in ms) */
#define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Timeout for Flash Write (in ms) */
#if CONFIG_SYS_MONITOR_BASE >= CONFIG_SYS_FLASH_BASE
#undef CONFIG_SYS_RAMBOOT
#else
#define CONFIG_SYS_RAMBOOT
#endif
/*-----------------------------------------------------------------------
* Cache Configuration
*/
#define CONFIG_SYS_CACHELINE_SIZE 32
#if defined(CONFIG_CMD_KGDB)
# define CONFIG_SYS_CACHELINE_SHIFT 5 /* log base 2 of the above value */
#endif
/*
* Internal Definitions
*
* Boot Flags
*/
#define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH */
#define BOOTFLAG_WARM 0x02 /* Software reboot */
#endif /* __CONFIG_H */