blob: dd95a67e2252dea19a8c99612dd5fa744a791a88 [file] [log] [blame]
/*
* Copyright 2014 Freescale Semiconductor, Inc.
*
* SPDX-License-Identifier: GPL-2.0+
*/
#ifndef __CONFIG_H
#define __CONFIG_H
#define CONFIG_LS102XA
#define CONFIG_ARMV7_PSCI_1_0
#define CONFIG_ARMV7_SECURE_BASE OCRAM_BASE_S_ADDR
#define CONFIG_SYS_FSL_CLK
#define CONFIG_SKIP_LOWLEVEL_INIT
#define CONFIG_BOARD_EARLY_INIT_F
#define CONFIG_DEEP_SLEEP
/*
* Size of malloc() pool
*/
#define CONFIG_SYS_MALLOC_LEN (CONFIG_ENV_SIZE + 16 * 1024 * 1024)
#define CONFIG_SYS_INIT_RAM_ADDR OCRAM_BASE_ADDR
#define CONFIG_SYS_INIT_RAM_SIZE OCRAM_SIZE
/*
* USB
*/
/*
* EHCI Support - disbaled by default as
* there is no signal coming out of soc on
* this board for this controller. However,
* the silicon still has this controller,
* and anyone can use this controller by
* taking signals out on their board.
*/
/*#define CONFIG_HAS_FSL_DR_USB*/
#ifdef CONFIG_HAS_FSL_DR_USB
#define CONFIG_USB_EHCI
#define CONFIG_USB_EHCI_FSL
#define CONFIG_EHCI_HCD_INIT_AFTER_RESET
#endif
/* XHCI Support - enabled by default */
#define CONFIG_HAS_FSL_XHCI_USB
#ifdef CONFIG_HAS_FSL_XHCI_USB
#define CONFIG_USB_XHCI_FSL
#define CONFIG_USB_MAX_CONTROLLER_COUNT 1
#define CONFIG_SYS_USB_XHCI_MAX_ROOT_PORTS 2
#endif
/*
* Generic Timer Definitions
*/
#define GENERIC_TIMER_CLK 12500000
#define CONFIG_SYS_CLK_FREQ 100000000
#define CONFIG_DDR_CLK_FREQ 100000000
#define DDR_SDRAM_CFG 0x470c0008
#define DDR_CS0_BNDS 0x008000bf
#define DDR_CS0_CONFIG 0x80014302
#define DDR_TIMING_CFG_0 0x50550004
#define DDR_TIMING_CFG_1 0xbcb38c56
#define DDR_TIMING_CFG_2 0x0040d120
#define DDR_TIMING_CFG_3 0x010e1000
#define DDR_TIMING_CFG_4 0x00000001
#define DDR_TIMING_CFG_5 0x03401400
#define DDR_SDRAM_CFG_2 0x00401010
#define DDR_SDRAM_MODE 0x00061c60
#define DDR_SDRAM_MODE_2 0x00180000
#define DDR_SDRAM_INTERVAL 0x18600618
#define DDR_DDR_WRLVL_CNTL 0x8655f605
#define DDR_DDR_WRLVL_CNTL_2 0x05060607
#define DDR_DDR_WRLVL_CNTL_3 0x05050505
#define DDR_DDR_CDR1 0x80040000
#define DDR_DDR_CDR2 0x00000001
#define DDR_SDRAM_CLK_CNTL 0x02000000
#define DDR_DDR_ZQ_CNTL 0x89080600
#define DDR_CS0_CONFIG_2 0
#define DDR_SDRAM_CFG_MEM_EN 0x80000000
#define SDRAM_CFG2_D_INIT 0x00000010
#define DDR_CDR2_VREF_TRAIN_EN 0x00000080
#define SDRAM_CFG2_FRC_SR 0x80000000
#define SDRAM_CFG_BI 0x00000001
#ifdef CONFIG_RAMBOOT_PBL
#define CONFIG_SYS_FSL_PBL_PBI board/freescale/ls1021atwr/ls102xa_pbi.cfg
#endif
#ifdef CONFIG_SD_BOOT
#ifdef CONFIG_SD_BOOT_QSPI
#define CONFIG_SYS_FSL_PBL_RCW \
board/freescale/ls1021atwr/ls102xa_rcw_sd_qspi.cfg
#else
#define CONFIG_SYS_FSL_PBL_RCW \
board/freescale/ls1021atwr/ls102xa_rcw_sd_ifc.cfg
#endif
#define CONFIG_SPL_FRAMEWORK
#define CONFIG_SPL_LDSCRIPT "arch/$(ARCH)/cpu/u-boot-spl.lds"
#define CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_SECTOR 0xe8
#ifdef CONFIG_SECURE_BOOT
#define CONFIG_U_BOOT_HDR_SIZE (16 << 10)
/*
* HDR would be appended at end of image and copied to DDR along
* with U-Boot image.
*/
#define CONFIG_SYS_U_BOOT_MAX_SIZE_SECTORS (0x400 + \
(CONFIG_U_BOOT_HDR_SIZE / 512)
#else
#define CONFIG_SYS_U_BOOT_MAX_SIZE_SECTORS 0x400
#endif /* ifdef CONFIG_SECURE_BOOT */
#define CONFIG_SPL_TEXT_BASE 0x10000000
#define CONFIG_SPL_MAX_SIZE 0x1a000
#define CONFIG_SPL_STACK 0x1001d000
#define CONFIG_SPL_PAD_TO 0x1c000
#define CONFIG_SYS_TEXT_BASE 0x82000000
#define CONFIG_SYS_SPL_MALLOC_START (CONFIG_SYS_TEXT_BASE + \
CONFIG_SYS_MONITOR_LEN)
#define CONFIG_SYS_SPL_MALLOC_SIZE 0x100000
#define CONFIG_SPL_BSS_START_ADDR 0x80100000
#define CONFIG_SPL_BSS_MAX_SIZE 0x80000
#ifdef CONFIG_U_BOOT_HDR_SIZE
/*
* HDR would be appended at end of image and copied to DDR along
* with U-Boot image. Here u-boot max. size is 512K. So if binary
* size increases then increase this size in case of secure boot as
* it uses raw u-boot image instead of fit image.
*/
#define CONFIG_SYS_MONITOR_LEN (0x80000 + CONFIG_U_BOOT_HDR_SIZE)
#else
#define CONFIG_SYS_MONITOR_LEN 0x80000
#endif /* ifdef CONFIG_U_BOOT_HDR_SIZE */
#endif
#ifdef CONFIG_QSPI_BOOT
#define CONFIG_SYS_TEXT_BASE 0x40010000
#endif
#if defined(CONFIG_QSPI_BOOT) || defined(CONFIG_SD_BOOT_QSPI)
#define CONFIG_SYS_NO_FLASH
#endif
#ifndef CONFIG_SYS_TEXT_BASE
#define CONFIG_SYS_TEXT_BASE 0x60100000
#endif
#define CONFIG_NR_DRAM_BANKS 1
#define PHYS_SDRAM 0x80000000
#define PHYS_SDRAM_SIZE (1u * 1024 * 1024 * 1024)
#define CONFIG_SYS_DDR_SDRAM_BASE 0x80000000UL
#define CONFIG_SYS_SDRAM_BASE CONFIG_SYS_DDR_SDRAM_BASE
#define CONFIG_FSL_CAAM /* Enable CAAM */
#if !defined(CONFIG_SD_BOOT) && !defined(CONFIG_NAND_BOOT) && \
!defined(CONFIG_QSPI_BOOT)
#define CONFIG_U_QE
#endif
/*
* IFC Definitions
*/
#if !defined(CONFIG_QSPI_BOOT) && !defined(CONFIG_SD_BOOT_QSPI)
#define CONFIG_FSL_IFC
#define CONFIG_SYS_FLASH_BASE 0x60000000
#define CONFIG_SYS_FLASH_BASE_PHYS CONFIG_SYS_FLASH_BASE
#define CONFIG_SYS_NOR0_CSPR_EXT (0x0)
#define CONFIG_SYS_NOR0_CSPR (CSPR_PHYS_ADDR(CONFIG_SYS_FLASH_BASE_PHYS) | \
CSPR_PORT_SIZE_16 | \
CSPR_MSEL_NOR | \
CSPR_V)
#define CONFIG_SYS_NOR_AMASK IFC_AMASK(128 * 1024 * 1024)
/* NOR Flash Timing Params */
#define CONFIG_SYS_NOR_CSOR (CSOR_NOR_ADM_SHIFT(4) | \
CSOR_NOR_TRHZ_80)
#define CONFIG_SYS_NOR_FTIM0 (FTIM0_NOR_TACSE(0x4) | \
FTIM0_NOR_TEADC(0x5) | \
FTIM0_NOR_TAVDS(0x0) | \
FTIM0_NOR_TEAHC(0x5))
#define CONFIG_SYS_NOR_FTIM1 (FTIM1_NOR_TACO(0x35) | \
FTIM1_NOR_TRAD_NOR(0x1A) | \
FTIM1_NOR_TSEQRAD_NOR(0x13))
#define CONFIG_SYS_NOR_FTIM2 (FTIM2_NOR_TCS(0x4) | \
FTIM2_NOR_TCH(0x4) | \
FTIM2_NOR_TWP(0x1c) | \
FTIM2_NOR_TWPH(0x0e))
#define CONFIG_SYS_NOR_FTIM3 0
#define CONFIG_FLASH_CFI_DRIVER
#define CONFIG_SYS_FLASH_CFI
#define CONFIG_SYS_FLASH_USE_BUFFER_WRITE
#define CONFIG_SYS_FLASH_QUIET_TEST
#define CONFIG_FLASH_SHOW_PROGRESS 45 /* count down from 45/5: 9..1 */
#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* number of banks */
#define CONFIG_SYS_MAX_FLASH_SECT 1024 /* sectors per device */
#define CONFIG_SYS_FLASH_ERASE_TOUT 60000 /* Flash Erase Timeout (ms) */
#define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Flash Write Timeout (ms) */
#define CONFIG_SYS_FLASH_EMPTY_INFO
#define CONFIG_SYS_FLASH_BANKS_LIST { CONFIG_SYS_FLASH_BASE_PHYS }
#define CONFIG_CFI_FLASH_USE_WEAK_ACCESSORS
#define CONFIG_SYS_WRITE_SWAPPED_DATA
#endif
/* CPLD */
#define CONFIG_SYS_CPLD_BASE 0x7fb00000
#define CPLD_BASE_PHYS CONFIG_SYS_CPLD_BASE
#define CONFIG_SYS_FPGA_CSPR_EXT (0x0)
#define CONFIG_SYS_FPGA_CSPR (CSPR_PHYS_ADDR(CPLD_BASE_PHYS) | \
CSPR_PORT_SIZE_8 | \
CSPR_MSEL_GPCM | \
CSPR_V)
#define CONFIG_SYS_FPGA_AMASK IFC_AMASK(64 * 1024)
#define CONFIG_SYS_FPGA_CSOR (CSOR_NOR_ADM_SHIFT(4) | \
CSOR_NOR_NOR_MODE_AVD_NOR | \
CSOR_NOR_TRHZ_80)
/* CPLD Timing parameters for IFC GPCM */
#define CONFIG_SYS_FPGA_FTIM0 (FTIM0_GPCM_TACSE(0xf) | \
FTIM0_GPCM_TEADC(0xf) | \
FTIM0_GPCM_TEAHC(0xf))
#define CONFIG_SYS_FPGA_FTIM1 (FTIM1_GPCM_TACO(0xff) | \
FTIM1_GPCM_TRAD(0x3f))
#define CONFIG_SYS_FPGA_FTIM2 (FTIM2_GPCM_TCS(0xf) | \
FTIM2_GPCM_TCH(0xf) | \
FTIM2_GPCM_TWP(0xff))
#define CONFIG_SYS_FPGA_FTIM3 0x0
#define CONFIG_SYS_CSPR0_EXT CONFIG_SYS_NOR0_CSPR_EXT
#define CONFIG_SYS_CSPR0 CONFIG_SYS_NOR0_CSPR
#define CONFIG_SYS_AMASK0 CONFIG_SYS_NOR_AMASK
#define CONFIG_SYS_CSOR0 CONFIG_SYS_NOR_CSOR
#define CONFIG_SYS_CS0_FTIM0 CONFIG_SYS_NOR_FTIM0
#define CONFIG_SYS_CS0_FTIM1 CONFIG_SYS_NOR_FTIM1
#define CONFIG_SYS_CS0_FTIM2 CONFIG_SYS_NOR_FTIM2
#define CONFIG_SYS_CS0_FTIM3 CONFIG_SYS_NOR_FTIM3
#define CONFIG_SYS_CSPR1_EXT CONFIG_SYS_FPGA_CSPR_EXT
#define CONFIG_SYS_CSPR1 CONFIG_SYS_FPGA_CSPR
#define CONFIG_SYS_AMASK1 CONFIG_SYS_FPGA_AMASK
#define CONFIG_SYS_CSOR1 CONFIG_SYS_FPGA_CSOR
#define CONFIG_SYS_CS1_FTIM0 CONFIG_SYS_FPGA_FTIM0
#define CONFIG_SYS_CS1_FTIM1 CONFIG_SYS_FPGA_FTIM1
#define CONFIG_SYS_CS1_FTIM2 CONFIG_SYS_FPGA_FTIM2
#define CONFIG_SYS_CS1_FTIM3 CONFIG_SYS_FPGA_FTIM3
/*
* Serial Port
*/
#ifdef CONFIG_LPUART
#define CONFIG_LPUART_32B_REG
#else
#define CONFIG_CONS_INDEX 1
#define CONFIG_SYS_NS16550_SERIAL
#ifndef CONFIG_DM_SERIAL
#define CONFIG_SYS_NS16550_REG_SIZE 1
#endif
#define CONFIG_SYS_NS16550_CLK get_serial_clock()
#endif
#define CONFIG_BAUDRATE 115200
/*
* I2C
*/
#define CONFIG_SYS_I2C
#define CONFIG_SYS_I2C_MXC
#define CONFIG_SYS_I2C_MXC_I2C1 /* enable I2C bus 1 */
#define CONFIG_SYS_I2C_MXC_I2C2 /* enable I2C bus 2 */
#define CONFIG_SYS_I2C_MXC_I2C3 /* enable I2C bus 3 */
/* EEPROM */
#define CONFIG_ID_EEPROM
#define CONFIG_SYS_I2C_EEPROM_NXID
#define CONFIG_SYS_EEPROM_BUS_NUM 1
#define CONFIG_SYS_I2C_EEPROM_ADDR 0x53
#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1
#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 3
#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 5
/*
* MMC
*/
#define CONFIG_MMC
#define CONFIG_FSL_ESDHC
#define CONFIG_GENERIC_MMC
#define CONFIG_DOS_PARTITION
/* SPI */
#if defined(CONFIG_QSPI_BOOT) || defined(CONFIG_SD_BOOT_QSPI)
/* QSPI */
#define QSPI0_AMBA_BASE 0x40000000
#define FSL_QSPI_FLASH_SIZE (1 << 24)
#define FSL_QSPI_FLASH_NUM 2
/* DSPI */
#endif
/* DM SPI */
#if defined(CONFIG_FSL_DSPI) || defined(CONFIG_FSL_QSPI)
#define CONFIG_DM_SPI_FLASH
#endif
/*
* Video
*/
#define CONFIG_FSL_DCU_FB
#ifdef CONFIG_FSL_DCU_FB
#define CONFIG_CMD_BMP
#define CONFIG_VIDEO_LOGO
#define CONFIG_VIDEO_BMP_LOGO
#define CONFIG_FSL_DCU_SII9022A
#define CONFIG_SYS_I2C_DVI_BUS_NUM 1
#define CONFIG_SYS_I2C_DVI_ADDR 0x39
#endif
/*
* eTSEC
*/
#define CONFIG_TSEC_ENET
#ifdef CONFIG_TSEC_ENET
#define CONFIG_MII
#define CONFIG_MII_DEFAULT_TSEC 1
#define CONFIG_TSEC1 1
#define CONFIG_TSEC1_NAME "eTSEC1"
#define CONFIG_TSEC2 1
#define CONFIG_TSEC2_NAME "eTSEC2"
#define CONFIG_TSEC3 1
#define CONFIG_TSEC3_NAME "eTSEC3"
#define TSEC1_PHY_ADDR 2
#define TSEC2_PHY_ADDR 0
#define TSEC3_PHY_ADDR 1
#define TSEC1_FLAGS (TSEC_GIGABIT | TSEC_REDUCED)
#define TSEC2_FLAGS (TSEC_GIGABIT | TSEC_REDUCED)
#define TSEC3_FLAGS (TSEC_GIGABIT | TSEC_REDUCED)
#define TSEC1_PHYIDX 0
#define TSEC2_PHYIDX 0
#define TSEC3_PHYIDX 0
#define CONFIG_ETHPRIME "eTSEC1"
#define CONFIG_PHY_GIGE
#define CONFIG_PHYLIB
#define CONFIG_PHY_ATHEROS
#define CONFIG_HAS_ETH0
#define CONFIG_HAS_ETH1
#define CONFIG_HAS_ETH2
#endif
/* PCIe */
#define CONFIG_PCI /* Enable PCI/PCIE */
#define CONFIG_PCIE1 /* PCIE controller 1 */
#define CONFIG_PCIE2 /* PCIE controller 2 */
#define CONFIG_PCIE_LAYERSCAPE /* Use common FSL Layerscape PCIe code */
#define FSL_PCIE_COMPAT "fsl,ls1021a-pcie"
#define CONFIG_SYS_PCI_64BIT
#define CONFIG_SYS_PCIE_CFG0_PHYS_OFF 0x00000000
#define CONFIG_SYS_PCIE_CFG0_SIZE 0x00001000 /* 4k */
#define CONFIG_SYS_PCIE_CFG1_PHYS_OFF 0x00001000
#define CONFIG_SYS_PCIE_CFG1_SIZE 0x00001000 /* 4k */
#define CONFIG_SYS_PCIE_IO_BUS 0x00000000
#define CONFIG_SYS_PCIE_IO_PHYS_OFF 0x00010000
#define CONFIG_SYS_PCIE_IO_SIZE 0x00010000 /* 64k */
#define CONFIG_SYS_PCIE_MEM_BUS 0x08000000
#define CONFIG_SYS_PCIE_MEM_PHYS_OFF 0x04000000
#define CONFIG_SYS_PCIE_MEM_SIZE 0x08000000 /* 128M */
#ifdef CONFIG_PCI
#define CONFIG_PCI_PNP
#define CONFIG_PCI_SCAN_SHOW
#define CONFIG_CMD_PCI
#endif
#define CONFIG_CMDLINE_TAG
#define CONFIG_CMDLINE_EDITING
#define CONFIG_PEN_ADDR_BIG_ENDIAN
#define CONFIG_LAYERSCAPE_NS_ACCESS
#define CONFIG_SMP_PEN_ADDR 0x01ee0200
#define CONFIG_TIMER_CLK_FREQ 12500000
#define CONFIG_HWCONFIG
#define HWCONFIG_BUFFER_SIZE 256
#define CONFIG_FSL_DEVICE_DISABLE
#ifdef CONFIG_LPUART
#define CONFIG_EXTRA_ENV_SETTINGS \
"bootargs=root=/dev/ram0 rw console=ttyLP0,115200\0" \
"initrd_high=0xffffffff\0" \
"fdt_high=0xffffffff\0"
#else
#define CONFIG_EXTRA_ENV_SETTINGS \
"bootargs=root=/dev/ram0 rw console=ttyS0,115200\0" \
"initrd_high=0xffffffff\0" \
"fdt_high=0xffffffff\0"
#endif
/*
* Miscellaneous configurable options
*/
#define CONFIG_SYS_LONGHELP /* undef to save memory */
#define CONFIG_AUTO_COMPLETE
#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */
#define CONFIG_SYS_PBSIZE \
(CONFIG_SYS_CBSIZE + sizeof(CONFIG_SYS_PROMPT) + 16)
#define CONFIG_SYS_MAXARGS 16 /* max number of command args */
#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE
#define CONFIG_SYS_MEMTEST_START 0x80000000
#define CONFIG_SYS_MEMTEST_END 0x9fffffff
#define CONFIG_SYS_LOAD_ADDR 0x82000000
#define CONFIG_LS102XA_STREAM_ID
/*
* Stack sizes
* The stack sizes are set up in start.S using the settings below
*/
#define CONFIG_STACKSIZE (30 * 1024)
#define CONFIG_SYS_INIT_SP_OFFSET \
(CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
#define CONFIG_SYS_INIT_SP_ADDR \
(CONFIG_SYS_INIT_RAM_ADDR + CONFIG_SYS_INIT_SP_OFFSET)
#ifdef CONFIG_SPL_BUILD
#define CONFIG_SYS_MONITOR_BASE CONFIG_SPL_TEXT_BASE
#else
#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE /* start of monitor */
#endif
#define CONFIG_SYS_QE_FW_ADDR 0x600c0000
/*
* Environment
*/
#define CONFIG_ENV_OVERWRITE
#if defined(CONFIG_SD_BOOT)
#define CONFIG_ENV_OFFSET 0x100000
#define CONFIG_ENV_IS_IN_MMC
#define CONFIG_SYS_MMC_ENV_DEV 0
#define CONFIG_ENV_SIZE 0x20000
#elif defined(CONFIG_QSPI_BOOT)
#define CONFIG_ENV_IS_IN_SPI_FLASH
#define CONFIG_ENV_SIZE 0x2000
#define CONFIG_ENV_OFFSET 0x100000
#define CONFIG_ENV_SECT_SIZE 0x10000
#else
#define CONFIG_ENV_IS_IN_FLASH
#define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE - CONFIG_ENV_SECT_SIZE)
#define CONFIG_ENV_SIZE 0x20000
#define CONFIG_ENV_SECT_SIZE 0x20000 /* 128K (one sector) */
#endif
#define CONFIG_MISC_INIT_R
/* Hash command with SHA acceleration supported in hardware */
#ifdef CONFIG_FSL_CAAM
#define CONFIG_CMD_HASH
#define CONFIG_SHA_HW_ACCEL
#endif
#include <asm/fsl_secure_boot.h>
#define CONFIG_SYS_BOOTM_LEN (64 << 20) /* Increase max gunzip size */
#endif