blob: 920edad0e9035ee2eeadc710d667e5a4b8f75c63 [file] [log] [blame]
/*
* Copyright 2010-2011 Freescale Semiconductor, Inc.
* Authors: Srikanth Srinivasan <srikanth.srinivasan@freescale.com>
* Timur Tabi <timur@freescale.com>
*
* This program is free software; you can redistribute it and/or modify it
* under the terms of the GNU General Public License as published by the Free
* Software Foundation; either version 2 of the License, or (at your option)
* any later version.
*/
#ifndef __CONFIG_H
#define __CONFIG_H
#include "../board/freescale/common/ics307_clk.h"
#ifdef CONFIG_36BIT
#define CONFIG_PHYS_64BIT
#endif
/* High Level Configuration Options */
#define CONFIG_BOOKE /* BOOKE */
#define CONFIG_E500 /* BOOKE e500 family */
#define CONFIG_MPC85xx /* MPC8540/60/55/41/48 */
#define CONFIG_P1022
#define CONFIG_P1022DS
#define CONFIG_MP /* support multiple processors */
#ifndef CONFIG_SYS_TEXT_BASE
#define CONFIG_SYS_TEXT_BASE 0xeff80000
#endif
#ifndef CONFIG_RESET_VECTOR_ADDRESS
#define CONFIG_RESET_VECTOR_ADDRESS 0xeffffffc
#endif
#define CONFIG_FSL_ELBC /* Has Enhanced localbus controller */
#define CONFIG_PCI /* Enable PCI/PCIE */
#define CONFIG_PCIE1 /* PCIE controler 1 (slot 1) */
#define CONFIG_PCIE2 /* PCIE controler 2 (slot 2) */
#define CONFIG_PCIE3 /* PCIE controler 3 (ULI bridge) */
#define CONFIG_FSL_PCI_INIT /* Use common FSL init code */
#define CONFIG_FSL_PCIE_RESET /* need PCIe reset errata */
#define CONFIG_SYS_PCI_64BIT /* enable 64-bit PCI resources */
#define CONFIG_ENABLE_36BIT_PHYS
#ifdef CONFIG_PHYS_64BIT
#define CONFIG_ADDR_MAP
#define CONFIG_SYS_NUM_ADDR_MAP 16 /* number of TLB1 entries */
#endif
#define CONFIG_FSL_LAW /* Use common FSL init code */
#define CONFIG_SYS_CLK_FREQ get_board_sys_clk()
#define CONFIG_DDR_CLK_FREQ get_board_ddr_clk()
#define CONFIG_ICS307_REFCLK_HZ 33333000 /* ICS307 clock chip ref freq */
/*
* These can be toggled for performance analysis, otherwise use default.
*/
#define CONFIG_L2_CACHE
#define CONFIG_BTB
#define CONFIG_SYS_MEMTEST_START 0x00000000
#define CONFIG_SYS_MEMTEST_END 0x7fffffff
#define CONFIG_SYS_CCSRBAR 0xffe00000
#define CONFIG_SYS_CCSRBAR_PHYS_LOW CONFIG_SYS_CCSRBAR
/* DDR Setup */
#define CONFIG_DDR_SPD
#define CONFIG_VERY_BIG_RAM
#define CONFIG_FSL_DDR3
#ifdef CONFIG_DDR_ECC
#define CONFIG_ECC_INIT_VIA_DDRCONTROLLER
#define CONFIG_MEM_INIT_VALUE 0xdeadbeef
#endif
#define CONFIG_SYS_DDR_SDRAM_BASE 0x00000000
#define CONFIG_SYS_SDRAM_BASE CONFIG_SYS_DDR_SDRAM_BASE
#define CONFIG_NUM_DDR_CONTROLLERS 1
#define CONFIG_DIMM_SLOTS_PER_CTLR 1
#define CONFIG_CHIP_SELECTS_PER_CTRL (2 * CONFIG_DIMM_SLOTS_PER_CTLR)
/* I2C addresses of SPD EEPROMs */
#define CONFIG_SYS_SPD_BUS_NUM 1
#define SPD_EEPROM_ADDRESS 0x51 /* CTLR 0 DIMM 0 */
/*
* Memory map
*
* 0x0000_0000 0x7fff_ffff DDR 2G Cacheable
* 0x8000_0000 0xdfff_ffff PCI Express Mem 1.5G non-cacheable
* 0xffc0_0000 0xffc2_ffff PCI IO range 192K non-cacheable
*
* Localbus cacheable (TBD)
* 0xXXXX_XXXX 0xXXXX_XXXX SRAM YZ M Cacheable
*
* Localbus non-cacheable
* 0xe000_0000 0xe80f_ffff Promjet/free 128M non-cacheable
* 0xe800_0000 0xefff_ffff FLASH 128M non-cacheable
* 0xffdf_0000 0xffdf_7fff PIXIS 32K non-cacheable TLB0
* 0xffd0_0000 0xffd0_3fff L1 for stack 16K Cacheable TLB0
* 0xffe0_0000 0xffef_ffff CCSR 1M non-cacheable
*/
/*
* Local Bus Definitions
*/
#define CONFIG_SYS_FLASH_BASE 0xe0000000 /* start of FLASH 128M */
#ifdef CONFIG_PHYS_64BIT
#define CONFIG_SYS_FLASH_BASE_PHYS 0xfe0000000ull
#else
#define CONFIG_SYS_FLASH_BASE_PHYS CONFIG_SYS_FLASH_BASE
#endif
#define CONFIG_FLASH_BR_PRELIM \
(BR_PHYS_ADDR((CONFIG_SYS_FLASH_BASE_PHYS + 0x8000000)) | BR_PS_16 | BR_V)
#define CONFIG_FLASH_OR_PRELIM (OR_AM_128MB | 0xff7)
#define CONFIG_SYS_BR0_PRELIM CONFIG_FLASH_BR_PRELIM /* NOR Base Address */
#define CONFIG_SYS_OR0_PRELIM CONFIG_FLASH_OR_PRELIM /* NOR Options */
#define CONFIG_SYS_BR1_PRELIM \
(BR_PHYS_ADDR(CONFIG_SYS_FLASH_BASE_PHYS) | BR_PS_16 | BR_V)
#define CONFIG_SYS_OR1_PRELIM CONFIG_FLASH_OR_PRELIM
#define CONFIG_SYS_FLASH_BANKS_LIST \
{CONFIG_SYS_FLASH_BASE_PHYS + 0x8000000, CONFIG_SYS_FLASH_BASE_PHYS}
#define CONFIG_SYS_FLASH_QUIET_TEST
#define CONFIG_FLASH_SHOW_PROGRESS 45 /* count down from 45/5: 9..1 */
#define CONFIG_SYS_MAX_FLASH_BANKS 2
#define CONFIG_SYS_MAX_FLASH_SECT 1024
#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE /* start of monitor */
#define CONFIG_FLASH_CFI_DRIVER
#define CONFIG_SYS_FLASH_CFI
#define CONFIG_SYS_FLASH_EMPTY_INFO
#define CONFIG_BOARD_EARLY_INIT_F
#define CONFIG_BOARD_EARLY_INIT_R
#define CONFIG_MISC_INIT_R
#define CONFIG_HWCONFIG
#define CONFIG_FSL_NGPIXIS
#define PIXIS_BASE 0xffdf0000 /* PIXIS registers */
#ifdef CONFIG_PHYS_64BIT
#define PIXIS_BASE_PHYS 0xfffdf0000ull
#else
#define PIXIS_BASE_PHYS PIXIS_BASE
#endif
#define CONFIG_SYS_BR2_PRELIM (BR_PHYS_ADDR(PIXIS_BASE_PHYS) | BR_PS_8 | BR_V)
#define CONFIG_SYS_OR2_PRELIM (OR_AM_32KB | 0x6ff7)
#define PIXIS_LBMAP_SWITCH 7
#define PIXIS_LBMAP_MASK 0xF0
#define PIXIS_LBMAP_ALTBANK 0x20
#define PIXIS_ELBC_SPI_MASK 0xc0
#define PIXIS_SPI 0x80
#define CONFIG_SYS_INIT_RAM_LOCK
#define CONFIG_SYS_INIT_RAM_ADDR 0xffd00000 /* Initial L1 address */
#define CONFIG_SYS_INIT_RAM_SIZE 0x00004000 /* Size of used area in RAM */
#define CONFIG_SYS_GBL_DATA_OFFSET \
(CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET
#define CONFIG_SYS_MONITOR_LEN (512 * 1024)
#define CONFIG_SYS_MALLOC_LEN (10 * 1024 * 1024)
/*
* Serial Port
*/
#define CONFIG_CONS_INDEX 1
#define CONFIG_SYS_NS16550
#define CONFIG_SYS_NS16550_SERIAL
#define CONFIG_SYS_NS16550_REG_SIZE 1
#define CONFIG_SYS_NS16550_CLK get_bus_freq(0)
#define CONFIG_SYS_BAUDRATE_TABLE \
{300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200}
#define CONFIG_SYS_NS16550_COM1 (CONFIG_SYS_CCSRBAR+0x4500)
#define CONFIG_SYS_NS16550_COM2 (CONFIG_SYS_CCSRBAR+0x4600)
/* Use the HUSH parser */
#define CONFIG_SYS_HUSH_PARSER
/* Video */
#define CONFIG_FSL_DIU_FB
#ifdef CONFIG_FSL_DIU_FB
#define CONFIG_SYS_DIU_ADDR (CONFIG_SYS_CCSRBAR + 0x10000)
#define CONFIG_VIDEO
#define CONFIG_CMD_BMP
#define CONFIG_CFB_CONSOLE
#define CONFIG_VIDEO_SW_CURSOR
#define CONFIG_VGA_AS_SINGLE_DEVICE
#define CONFIG_VIDEO_LOGO
#define CONFIG_VIDEO_BMP_LOGO
#define CONFIG_CFI_FLASH_USE_WEAK_ACCESSORS
/*
* With CONFIG_CFI_FLASH_USE_WEAK_ACCESSORS, flash I/O is really slow, so
* disable empty flash sector detection, which is I/O-intensive.
*/
#undef CONFIG_SYS_FLASH_EMPTY_INFO
#endif
#ifndef CONFIG_FSL_DIU_FB
#define CONFIG_ATI
#endif
#ifdef CONFIG_ATI
#define VIDEO_IO_OFFSET CONFIG_SYS_PCIE1_IO_VIRT
#define CONFIG_VIDEO
#define CONFIG_BIOSEMU
#define CONFIG_VIDEO_SW_CURSOR
#define CONFIG_ATI_RADEON_FB
#define CONFIG_VIDEO_LOGO
#define CONFIG_SYS_ISA_IO_BASE_ADDRESS VIDEO_IO_OFFSET
#define CONFIG_CFB_CONSOLE
#define CONFIG_VGA_AS_SINGLE_DEVICE
#endif
/*
* Pass open firmware flat tree
*/
#define CONFIG_OF_LIBFDT
#define CONFIG_OF_BOARD_SETUP
#define CONFIG_OF_STDOUT_VIA_ALIAS
/* new uImage format support */
#define CONFIG_FIT
#define CONFIG_FIT_VERBOSE
/* I2C */
#define CONFIG_FSL_I2C
#define CONFIG_HARD_I2C
#define CONFIG_I2C_MULTI_BUS
#define CONFIG_SYS_I2C_SPEED 400000
#define CONFIG_SYS_I2C_EEPROM_ADDR 0x57
#define CONFIG_SYS_I2C_SLAVE 0x7F
#define CONFIG_SYS_I2C_NOPROBES {{0, 0x29}}
#define CONFIG_SYS_I2C_OFFSET 0x3000
#define CONFIG_SYS_I2C2_OFFSET 0x3100
/*
* I2C2 EEPROM
*/
#define CONFIG_ID_EEPROM
#define CONFIG_SYS_I2C_EEPROM_NXID
#define CONFIG_SYS_I2C_EEPROM_ADDR 0x57
#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1
#define CONFIG_SYS_EEPROM_BUS_NUM 1
/*
* eSPI - Enhanced SPI
*/
#define CONFIG_SPI_FLASH
#define CONFIG_SPI_FLASH_SPANSION
#define CONFIG_HARD_SPI
#define CONFIG_FSL_ESPI
#define CONFIG_CMD_SF
#define CONFIG_SF_DEFAULT_SPEED 10000000
#define CONFIG_SF_DEFAULT_MODE 0
/*
* General PCI
* Memory space is mapped 1-1, but I/O space must start from 0.
*/
/* controller 1, Slot 2, tgtid 1, Base address a000 */
#define CONFIG_SYS_PCIE1_MEM_VIRT 0xc0000000
#ifdef CONFIG_PHYS_64BIT
#define CONFIG_SYS_PCIE1_MEM_BUS 0xe0000000
#define CONFIG_SYS_PCIE1_MEM_PHYS 0xc40000000ull
#else
#define CONFIG_SYS_PCIE1_MEM_BUS 0xc0000000
#define CONFIG_SYS_PCIE1_MEM_PHYS 0xc0000000
#endif
#define CONFIG_SYS_PCIE1_MEM_SIZE 0x20000000 /* 512M */
#define CONFIG_SYS_PCIE1_IO_VIRT 0xffc20000
#define CONFIG_SYS_PCIE1_IO_BUS 0x00000000
#ifdef CONFIG_PHYS_64BIT
#define CONFIG_SYS_PCIE1_IO_PHYS 0xfffc20000ull
#else
#define CONFIG_SYS_PCIE1_IO_PHYS 0xffc20000
#endif
#define CONFIG_SYS_PCIE1_IO_SIZE 0x00010000 /* 64k */
/* controller 2, direct to uli, tgtid 2, Base address 9000 */
#define CONFIG_SYS_PCIE2_MEM_VIRT 0xa0000000
#ifdef CONFIG_PHYS_64BIT
#define CONFIG_SYS_PCIE2_MEM_BUS 0xe0000000
#define CONFIG_SYS_PCIE2_MEM_PHYS 0xc20000000ull
#else
#define CONFIG_SYS_PCIE2_MEM_BUS 0xa0000000
#define CONFIG_SYS_PCIE2_MEM_PHYS 0xa0000000
#endif
#define CONFIG_SYS_PCIE2_MEM_SIZE 0x20000000 /* 512M */
#define CONFIG_SYS_PCIE2_IO_VIRT 0xffc10000
#define CONFIG_SYS_PCIE2_IO_BUS 0x00000000
#ifdef CONFIG_PHYS_64BIT
#define CONFIG_SYS_PCIE2_IO_PHYS 0xfffc10000ull
#else
#define CONFIG_SYS_PCIE2_IO_PHYS 0xffc10000
#endif
#define CONFIG_SYS_PCIE2_IO_SIZE 0x00010000 /* 64k */
/* controller 3, Slot 1, tgtid 3, Base address b000 */
#define CONFIG_SYS_PCIE3_MEM_VIRT 0x80000000
#ifdef CONFIG_PHYS_64BIT
#define CONFIG_SYS_PCIE3_MEM_BUS 0xe0000000
#define CONFIG_SYS_PCIE3_MEM_PHYS 0xc00000000ull
#else
#define CONFIG_SYS_PCIE3_MEM_BUS 0x80000000
#define CONFIG_SYS_PCIE3_MEM_PHYS 0x80000000
#endif
#define CONFIG_SYS_PCIE3_MEM_SIZE 0x20000000 /* 512M */
#define CONFIG_SYS_PCIE3_IO_VIRT 0xffc00000
#define CONFIG_SYS_PCIE3_IO_BUS 0x00000000
#ifdef CONFIG_PHYS_64BIT
#define CONFIG_SYS_PCIE3_IO_PHYS 0xfffc00000ull
#else
#define CONFIG_SYS_PCIE3_IO_PHYS 0xffc00000
#endif
#define CONFIG_SYS_PCIE3_IO_SIZE 0x00010000 /* 64k */
#ifdef CONFIG_PCI
#define CONFIG_PCI_PNP /* do pci plug-and-play */
#define CONFIG_PCI_SCAN_SHOW /* show pci devices on startup */
#define CONFIG_E1000 /* Define e1000 pci Ethernet card */
#endif
/* SATA */
#define CONFIG_LIBATA
#define CONFIG_FSL_SATA
#define CONFIG_SYS_SATA_MAX_DEVICE 2
#define CONFIG_SATA1
#define CONFIG_SYS_SATA1 CONFIG_SYS_MPC85xx_SATA1_ADDR
#define CONFIG_SYS_SATA1_FLAGS FLAGS_DMA
#define CONFIG_SATA2
#define CONFIG_SYS_SATA2 CONFIG_SYS_MPC85xx_SATA2_ADDR
#define CONFIG_SYS_SATA2_FLAGS FLAGS_DMA
#ifdef CONFIG_FSL_SATA
#define CONFIG_LBA48
#define CONFIG_CMD_SATA
#define CONFIG_DOS_PARTITION
#define CONFIG_CMD_EXT2
#endif
#define CONFIG_MMC
#ifdef CONFIG_MMC
#define CONFIG_CMD_MMC
#define CONFIG_FSL_ESDHC
#define CONFIG_GENERIC_MMC
#define CONFIG_SYS_FSL_ESDHC_ADDR CONFIG_SYS_MPC85xx_ESDHC_ADDR
#endif
#if defined(CONFIG_MMC) || defined(CONFIG_USB_EHCI)
#define CONFIG_CMD_EXT2
#define CONFIG_CMD_FAT
#define CONFIG_DOS_PARTITION
#endif
#define CONFIG_TSEC_ENET
#ifdef CONFIG_TSEC_ENET
#define CONFIG_TSECV2
#define CONFIG_MII /* MII PHY management */
#define CONFIG_TSEC1 1
#define CONFIG_TSEC1_NAME "eTSEC1"
#define CONFIG_TSEC2 1
#define CONFIG_TSEC2_NAME "eTSEC2"
#define TSEC1_PHY_ADDR 1
#define TSEC2_PHY_ADDR 2
#define TSEC1_FLAGS (TSEC_GIGABIT | TSEC_REDUCED)
#define TSEC2_FLAGS (TSEC_GIGABIT | TSEC_REDUCED)
#define TSEC1_PHYIDX 0
#define TSEC2_PHYIDX 0
#define CONFIG_ETHPRIME "eTSEC1"
#define CONFIG_PHY_GIGE /* Include GbE speed/duplex detection */
#endif
/*
* Environment
*/
#define CONFIG_ENV_IS_IN_FLASH
#define CONFIG_ENV_OVERWRITE
#define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE - CONFIG_ENV_SECT_SIZE)
#define CONFIG_ENV_SIZE 0x2000
#define CONFIG_ENV_SECT_SIZE 0x20000
#define CONFIG_LOADS_ECHO
#define CONFIG_SYS_LOADS_BAUD_CHANGE
/*
* Command line configuration.
*/
#include <config_cmd_default.h>
#define CONFIG_CMD_ELF
#define CONFIG_CMD_ERRATA
#define CONFIG_CMD_IRQ
#define CONFIG_CMD_I2C
#define CONFIG_CMD_MII
#define CONFIG_CMD_PING
#define CONFIG_CMD_SETEXPR
#define CONFIG_CMD_REGINFO
#ifdef CONFIG_PCI
#define CONFIG_CMD_PCI
#define CONFIG_CMD_NET
#endif
/*
* USB
*/
#define CONFIG_USB_EHCI
#ifdef CONFIG_USB_EHCI
#define CONFIG_CMD_USB
#define CONFIG_EHCI_HCD_INIT_AFTER_RESET
#define CONFIG_USB_EHCI_FSL
#define CONFIG_USB_STORAGE
#define CONFIG_CMD_FAT
#endif
/*
* Miscellaneous configurable options
*/
#define CONFIG_SYS_LONGHELP /* undef to save memory */
#define CONFIG_CMDLINE_EDITING /* Command-line editing */
#define CONFIG_AUTO_COMPLETE /* add autocompletion support */
#define CONFIG_SYS_LOAD_ADDR 0x2000000 /* default load address */
#define CONFIG_SYS_PROMPT "=> " /* Monitor Command Prompt */
#ifdef CONFIG_CMD_KGDB
#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */
#else
#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */
#endif
/* Print Buffer Size */
#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE + sizeof(CONFIG_SYS_PROMPT) + 16)
#define CONFIG_SYS_MAXARGS 16
#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE
#define CONFIG_SYS_HZ 1000
/*
* For booting Linux, the board info and command line data
* have to be in the first 64 MB of memory, since this is
* the maximum mapped by the Linux kernel during initialization.
*/
#define CONFIG_SYS_BOOTMAPSZ (64 << 20) /* Initial Memory map for Linux*/
#define CONFIG_SYS_BOOTM_LEN (64 << 20) /* Increase max gunzip size */
#ifdef CONFIG_CMD_KGDB
#define CONFIG_KGDB_BAUDRATE 230400 /* speed to run kgdb serial port */
#define CONFIG_KGDB_SER_INDEX 2 /* which serial port to use */
#endif
/*
* Environment Configuration
*/
#define CONFIG_HOSTNAME p1022ds
#define CONFIG_ROOTPATH "/opt/nfsroot"
#define CONFIG_BOOTFILE "uImage"
#define CONFIG_UBOOTPATH u-boot.bin /* U-Boot image on TFTP server */
#define CONFIG_LOADADDR 1000000
#define CONFIG_BOOTDELAY 10 /* -1 disables auto-boot */
#define CONFIG_BOOTARGS
#define CONFIG_BAUDRATE 115200
#define CONFIG_EXTRA_ENV_SETTINGS \
"perf_mode=stable\0" \
"memctl_intlv_ctl=2\0" \
"netdev=eth0\0" \
"uboot=" MK_STR(CONFIG_UBOOTPATH) "\0" \
"tftpflash=tftpboot $loadaddr $uboot; " \
"protect off " MK_STR(CONFIG_SYS_TEXT_BASE) " +$filesize; " \
"erase " MK_STR(CONFIG_SYS_TEXT_BASE) " +$filesize; " \
"cp.b $loadaddr " MK_STR(CONFIG_SYS_TEXT_BASE) " $filesize; " \
"protect on " MK_STR(CONFIG_SYS_TEXT_BASE) " +$filesize; " \
"cmp.b $loadaddr " MK_STR(CONFIG_SYS_TEXT_BASE) " $filesize\0" \
"consoledev=ttyS0\0" \
"ramdiskaddr=2000000\0" \
"ramdiskfile=uramdisk\0" \
"fdtaddr=c00000\0" \
"fdtfile=p1022ds.dtb\0" \
"bdev=sda3\0" \
"diuregs=md e002c000 1d\0" \
"dium=mw e002c01c\0" \
"diuerr=md e002c014 1\0" \
"hwconfig=esdhc;audclk:12\0"
#define CONFIG_HDBOOT \
"setenv bootargs root=/dev/$bdev rw " \
"console=$consoledev,$baudrate $othbootargs;" \
"tftp $loadaddr $bootfile;" \
"tftp $fdtaddr $fdtfile;" \
"bootm $loadaddr - $fdtaddr"
#define CONFIG_NFSBOOTCOMMAND \
"setenv bootargs root=/dev/nfs rw " \
"nfsroot=$serverip:$rootpath " \
"ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname:$netdev:off " \
"console=$consoledev,$baudrate $othbootargs;" \
"tftp $loadaddr $bootfile;" \
"tftp $fdtaddr $fdtfile;" \
"bootm $loadaddr - $fdtaddr"
#define CONFIG_RAMBOOTCOMMAND \
"setenv bootargs root=/dev/ram rw " \
"console=$consoledev,$baudrate $othbootargs;" \
"tftp $ramdiskaddr $ramdiskfile;" \
"tftp $loadaddr $bootfile;" \
"tftp $fdtaddr $fdtfile;" \
"bootm $loadaddr $ramdiskaddr $fdtaddr"
#define CONFIG_BOOTCOMMAND CONFIG_RAMBOOTCOMMAND
#endif