diff --git a/include/configs/taishan.h b/include/configs/taishan.h
new file mode 100644
index 0000000..7ace397
--- /dev/null
+++ b/include/configs/taishan.h
@@ -0,0 +1,333 @@
+/*
+ * (C) Copyright 2007
+ * Stefan Roese, DENX Software Engineering, sr@denx.de.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+/************************************************************************
+ * TAISHAN.h - configuration for AMCC 440GX Ref
+ ***********************************************************************/
+
+#ifndef __CONFIG_H
+#define __CONFIG_H
+
+/*-----------------------------------------------------------------------
+ * High Level Configuration Options
+ *----------------------------------------------------------------------*/
+#define CONFIG_TAISHAN		1	/* Board is taishan		*/
+#define CONFIG_440GX		1	/* Specifc GX support		*/
+#define CONFIG_4xx		1	/* ... PPC4xx family		*/
+#undef	CFG_DRAM_TEST			/* Disable-takes long time!	*/
+#define CONFIG_SYS_CLK_FREQ	33333333 /* external freq to pll	*/
+
+#define CONFIG_BOARD_EARLY_INIT_F 1	/* Call board_pre_init		*/
+#define CONFIG_MISC_INIT_R	1	/* Call misc_init_r		*/
+
+/*-----------------------------------------------------------------------
+ * Base addresses -- Note these are effective addresses where the
+ * actual resources get mapped (not physical addresses)
+ *----------------------------------------------------------------------*/
+#define CFG_SDRAM_BASE		0x00000000	/* _must_ be 0		*/
+#define CFG_FLASH_BASE		0xfc000000	/* start of FLASH	*/
+#define CFG_MONITOR_BASE	0xfffc0000	/* start of monitor	*/
+#define CFG_PCI_MEMBASE		0x80000000	/* mapped pci memory	*/
+#define CFG_PERIPHERAL_BASE	0xe0000000	/* internal peripherals	*/
+#define CFG_ISRAM_BASE		0xc0000000	/* internal SRAM	*/
+#define CFG_PCI_BASE		0xd0000000	/* internal PCI regs	*/
+
+#define CFG_EBC0_FLASH_BASE	CFG_FLASH_BASE
+#define CFG_EBC1_FPGA_BASE	(CFG_PERIPHERAL_BASE + 0x01000000)
+#define CFG_EBC2_LCM_BASE	(CFG_PERIPHERAL_BASE + 0x02000000)
+#define CFG_EBC3_CONN_BASE	(CFG_PERIPHERAL_BASE + 0x08000000)
+
+#define CFG_GPIO_BASE		(CFG_PERIPHERAL_BASE + 0x00000700)
+
+/*-----------------------------------------------------------------------
+ * Initial RAM & stack pointer (placed in internal SRAM)
+ *----------------------------------------------------------------------*/
+#define CFG_TEMP_STACK_OCM	1
+#define CFG_OCM_DATA_ADDR	CFG_ISRAM_BASE
+#define CFG_INIT_RAM_ADDR	CFG_ISRAM_BASE  /* Initial RAM address	*/
+#define CFG_INIT_RAM_END	0x2000		/* End of used area in RAM*/
+#define CFG_GBL_DATA_SIZE	128		/* num bytes initial data*/
+
+#define CFG_GBL_DATA_OFFSET	(CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE)
+#define CFG_POST_WORD_ADDR	(CFG_GBL_DATA_OFFSET - 0x4)
+#define CFG_INIT_SP_OFFSET	CFG_POST_WORD_ADDR
+
+#define CFG_MONITOR_LEN		(256 * 1024)	/* Reserve 256 kB for Mon*/
+#define CFG_MALLOC_LEN		(1024 * 1024)	/* Reserve 1024 kB for malloc*/
+
+/*-----------------------------------------------------------------------
+ * Serial Port
+ *----------------------------------------------------------------------*/
+#define CONFIG_UART1_CONSOLE	1	/* use of UART1 as console	*/
+#define CONFIG_SERIAL_MULTI     1	/* enable serial multi support	*/
+#define CFG_EXT_SERIAL_CLOCK	(1843200 * 6)	/* Ext clk @ 11.059 MHz */
+#define CONFIG_BAUDRATE		115200
+
+#define CFG_BAUDRATE_TABLE  \
+    {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200}
+
+/*-----------------------------------------------------------------------
+ * Environment
+ *----------------------------------------------------------------------*/
+#define CFG_ENV_IS_IN_FLASH     1	/* use FLASH for environment vars	*/
+
+/*-----------------------------------------------------------------------
+ * FLASH related
+ *----------------------------------------------------------------------*/
+#define CFG_FLASH_CFI
+#define CFG_FLASH_CFI_DRIVER
+#define CFG_FLASH_EMPTY_INFO		/* print 'E' for empty sector on flinfo */
+#define CFG_FLASH_USE_BUFFER_WRITE 1	/* use buffered writes (20x faster)	*/
+
+#define CFG_FLASH_BANKS_LIST    {CFG_FLASH_BASE}
+#define CFG_MAX_FLASH_BANKS     1		    /* number of banks	    */
+#define CFG_MAX_FLASH_SECT	1024		    /* sectors per device   */
+
+#undef	CFG_FLASH_CHECKSUM
+#define CFG_FLASH_ERASE_TOUT	120000	/* Timeout for Flash Erase (in ms)	*/
+#define CFG_FLASH_WRITE_TOUT	500	/* Timeout for Flash Write (in ms)	*/
+
+#define CFG_ENV_SECT_SIZE	0x40000 /* size of one complete sector	*/
+#define CFG_ENV_ADDR		(CFG_MONITOR_BASE-CFG_ENV_SECT_SIZE)
+#define	CFG_ENV_SIZE		0x4000	/* Total Size of Environment Sector	*/
+
+/* Address and size of Redundant Environment Sector	*/
+#define CFG_ENV_ADDR_REDUND	(CFG_ENV_ADDR-CFG_ENV_SECT_SIZE)
+#define CFG_ENV_SIZE_REDUND	(CFG_ENV_SIZE)
+
+/*-----------------------------------------------------------------------
+ * E2PROM bootstrap configure value
+ *----------------------------------------------------------------------*/
+
+/*
+ * 800/133/66
+ * IIC 0~15: 86 78 11 6a 61 A7 04 62 00 00 00 00 00 00 00 00
+ */
+
+/*
+ * 800/160/80
+ * IIC 0~15: 86 78 c1 a6 09 67 04 63 00 00 00 00 00 00 00 00
+ */
+
+/*-----------------------------------------------------------------------
+ * DDR SDRAM
+ *----------------------------------------------------------------------*/
+#undef CONFIG_SPD_EEPROM		/* Don't use SPD EEPROM for setup	*/
+#define CONFIG_SDRAM_BANK0	1	/* init onboard DDR SDRAM bank 0	*/
+#define	CFG_SDRAM0_TR0		0xC10A401A
+#undef CONFIG_SDRAM_ECC			/* enable ECC support			*/
+
+/*-----------------------------------------------------------------------
+ * I2C
+ *----------------------------------------------------------------------*/
+#define CONFIG_HARD_I2C		1	/* I2C with hardware support	*/
+#undef	CONFIG_SOFT_I2C			/* I2C bit-banged		*/
+#define CFG_I2C_SPEED		400000	/* I2C speed and slave address	*/
+#define CFG_I2C_SLAVE		0x7F
+
+#undef CFG_I2C_MULTI_EEPROMS
+#define CFG_I2C_EEPROM_ADDR	0x50
+#define CFG_I2C_EEPROM_ADDR_LEN 1
+#define CFG_EEPROM_PAGE_WRITE_ENABLE
+#define CFG_EEPROM_PAGE_WRITE_BITS 3
+#define CFG_EEPROM_PAGE_WRITE_DELAY_MS 10
+
+#define CFG_BOOTSTRAP_IIC_ADDR	0x50
+
+/* I2C SYSMON (LM75, AD7414 is almost compatible)			*/
+#define CONFIG_DTT_LM75		1		/* ON Semi's LM75	*/
+#define CONFIG_DTT_SENSORS	{0}		/* Sensor addresses	*/
+#define CFG_DTT_MAX_TEMP	70
+#define CFG_DTT_LOW_TEMP	-30
+#define CFG_DTT_HYSTERESIS	3
+
+/*-----------------------------------------------------------------------
+ * Environment
+ *----------------------------------------------------------------------*/
+
+#define CONFIG_PREBOOT	"echo;"	\
+	"echo Type \"run flash_nfs\" to mount root filesystem over NFS;" \
+	"echo"
+
+#undef	CONFIG_BOOTARGS
+
+#define	CONFIG_EXTRA_ENV_SETTINGS					\
+	"netdev=eth0\0"							\
+	"hostname=taishan\0"						\
+	"nfsargs=setenv bootargs root=/dev/nfs rw "			\
+		"nfsroot=${serverip}:${rootpath}\0"			\
+	"ramargs=setenv bootargs root=/dev/ram rw\0"			\
+	"addip=setenv bootargs ${bootargs} "				\
+		"ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}"	\
+		":${hostname}:${netdev}:off panic=1\0"			\
+	"addtty=setenv bootargs ${bootargs} console=ttyS1,${baudrate}\0"\
+	"flash_nfs=run nfsargs addip addtty;"				\
+		"bootm ${kernel_addr}\0"				\
+	"flash_self=run ramargs addip addtty;"				\
+		"bootm ${kernel_addr} ${ramdisk_addr}\0"		\
+	"net_nfs=tftp 200000 ${bootfile};run nfsargs addip addtty;"     \
+	        "bootm\0"						\
+	"rootpath=/opt/eldk/ppc_4xx\0"					\
+	"bootfile=/tftpboot/taishan/uImage\0"				\
+	"kernel_addr=fc000000\0"					\
+	"ramdisk_addr=fc180000\0"					\
+	"load=tftp 100000 /tftpboot/taishan/u-boot.bin\0"		\
+	"update=protect off fffc0000 ffffffff;era fffc0000 ffffffff;"	\
+		"cp.b 100000 fffc0000 40000;"			        \
+		"setenv filesize;saveenv\0"				\
+	"upd=run load;run update\0"					\
+	"fixedip=setenv bootargs $(bootargs) ip=$(ipaddr):$(serverip):" \
+	"$(gatewayip):$(netmask):$(hostname):$(netdev):off panic=1\0"	\
+	"dhcp=setenv bootargs $(bootargs) ip=dhcp\0"			\
+	"kozio=bootm 0xffe00000\0"					\
+	""
+#define CONFIG_BOOTCOMMAND	"run flash_self"
+
+#if 0
+#define CONFIG_BOOTDELAY	-1	/* autoboot disabled		*/
+#else
+#define CONFIG_BOOTDELAY	5	/* autoboot after 5 seconds	*/
+#endif
+
+#define CONFIG_BAUDRATE		115200
+#define CONFIG_LOADS_ECHO	1	/* echo on for serial download	*/
+#define CFG_LOADS_BAUD_CHANGE	1	/* allow baudrate change	*/
+
+/*-----------------------------------------------------------------------
+ * Networking
+ *----------------------------------------------------------------------*/
+#define CONFIG_EMAC_NR_START	2	/* start with EMAC 2 (skip 0&1)	*/
+#define CONFIG_MII		1	/* MII PHY management		*/
+#define CONFIG_NET_MULTI	1
+#define CONFIG_PHY_ADDR	      	0xff	     /* no phy on EMAC0		*/
+#define CONFIG_PHY1_ADDR      	0xff	     /* no phy on EMAC1		*/
+#define CONFIG_PHY2_ADDR	0x1
+#define CONFIG_PHY3_ADDR	0x3
+#define CONFIG_ET1011C_PHY	1
+#define CONFIG_HAS_ETH0
+#define CONFIG_HAS_ETH1
+#define CONFIG_HAS_ETH2
+#define CONFIG_HAS_ETH3
+#define CONFIG_PHY_GIGE		1	/* Include GbE speed/duplex detection */
+#define CONFIG_PHY_RESET        1       /* reset phy upon startup         */
+#define CONFIG_PHY_RESET_DELAY	1000
+#define CFG_RX_ETH_BUFFER	32	/* Number of ethernet rx buffers & descriptors */
+
+#define CONFIG_NETCONSOLE		/* include NetConsole support	*/
+
+/*-----------------------------------------------------------------------
+ * Console/Commands/Parser
+ *----------------------------------------------------------------------*/
+#define CONFIG_COMMANDS	       (CONFIG_CMD_DFL	| \
+				CFG_CMD_ASKENV	| \
+				CFG_CMD_DHCP	| \
+				CFG_CMD_DIAG	| \
+				CFG_CMD_DTT	| \
+				CFG_CMD_ELF	| \
+				CFG_CMD_EEPROM	| \
+				CFG_CMD_I2C	| \
+				CFG_CMD_IRQ	| \
+				CFG_CMD_MII	| \
+				CFG_CMD_NET	| \
+				CFG_CMD_NFS	| \
+				CFG_CMD_PCI	| \
+				CFG_CMD_PING	| \
+				CFG_CMD_REGINFO)
+
+/* this must be included AFTER the definition of CONFIG_COMMANDS (if any) */
+#include <cmd_confdefs.h>
+
+#undef CONFIG_WATCHDOG			/* watchdog disabled		*/
+
+/*-----------------------------------------------------------------------
+ * Miscellaneous configurable options
+ *----------------------------------------------------------------------*/
+#define CFG_LONGHELP			/* undef to save memory		*/
+#define CFG_PROMPT	        "=> "	/* Monitor Command Prompt	*/
+#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
+#define CFG_CBSIZE	        1024	/* Console I/O Buffer Size	*/
+#else
+#define CFG_CBSIZE	        256	/* Console I/O Buffer Size	*/
+#endif
+#define CFG_PBSIZE              (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */
+#define CFG_MAXARGS	        16	/* max number of command args	*/
+#define CFG_BARGSIZE	        CFG_CBSIZE /* Boot Argument Buffer Size	*/
+
+#define CFG_MEMTEST_START	0x0400000 /* memtest works on		*/
+#define CFG_MEMTEST_END		0x0C00000 /* 4 ... 12 MB in DRAM	*/
+
+#define CFG_LOAD_ADDR		0x100000  /* default load address	*/
+#define CFG_EXTBDINFO		1	/* To use extended board_into (bd_t) */
+
+#define CFG_HZ		        1000	/* decrementer freq: 1 ms ticks	*/
+
+#define CONFIG_CMDLINE_EDITING	1	/* add command line history	*/
+#define CONFIG_LOOPW            1       /* enable loopw command         */
+#define CONFIG_MX_CYCLIC        1       /* enable mdc/mwc commands      */
+#define CONFIG_ZERO_BOOTDELAY_CHECK	/* check for keypress on bootdelay==0 */
+#define CONFIG_VERSION_VARIABLE 1	/* include version env variable */
+
+/*-----------------------------------------------------------------------
+ * PCI stuff
+ *-----------------------------------------------------------------------
+ */
+/* General PCI */
+#define CONFIG_PCI			/* include pci support		*/
+#define CONFIG_PCI_PNP			/* do pci plug-and-play		*/
+#define CONFIG_EEPRO100       1		/* include PCI EEPRO100		*/
+#define CONFIG_PCI_SCAN_SHOW		/* show pci devices on startup	*/
+#define CFG_PCI_TARGBASE    0x80000000	/* PCIaddr mapped to CFG_PCI_MEMBASE */
+
+/* Board-specific PCI */
+#define CFG_PCI_PRE_INIT		/* enable board pci_pre_init()	*/
+#define CFG_PCI_TARGET_INIT		/* let board init pci target    */
+
+#define CFG_PCI_SUBSYS_VENDORID 0x10e8	/* AMCC */
+#define CFG_PCI_SUBSYS_DEVICEID 0xcafe	/* Whatever */
+
+/*
+ * For booting Linux, the board info and command line data
+ * have to be in the first 8 MB of memory, since this is
+ * the maximum mapped by the Linux kernel during initialization.
+ */
+#define CFG_BOOTMAPSZ		(8 << 20)	/* Initial Memory map for Linux */
+
+/*-----------------------------------------------------------------------
+ * Cache Configuration
+ *----------------------------------------------------------------------*/
+#define CFG_DCACHE_SIZE		32768	/* For AMCC 440 CPUs			*/
+#define CFG_CACHELINE_SIZE	32	/* ...			*/
+#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
+#define CFG_CACHELINE_SHIFT	5	/* log base 2 of the above value	*/
+#endif
+
+/*
+ * Internal Definitions
+ *
+ * Boot Flags
+ */
+#define BOOTFLAG_COLD	0x01		/* Normal Power-On: Boot from FLASH	*/
+#define BOOTFLAG_WARM	0x02		/* Software reboot			*/
+
+#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
+#define CONFIG_KGDB_BAUDRATE	230400	/* speed to run kgdb serial port */
+#define CONFIG_KGDB_SER_INDEX	2	/* which serial port to use */
+#endif
+#endif	/* __CONFIG_H */