blob: d94e9c60eafa12a0b04dc37959084300d9a8b193 [file] [log] [blame]
/*
* (C) Copyright 2006
* Stefan Roese, DENX Software Engineering, sr@denx.de.
*
* Based on original work by
* Roel Loeffen, (C) Copyright 2006 Prodrive B.V.
*
* SPDX-License-Identifier: GPL-2.0+
*/
/************************************************************************
* p3mx.h - configuration for Prodrive P3M750 & P3M7448 boards
*
* The defines:
* CONFIG_P3M750 or
* CONFIG_P3M7448
* are written into include/config.h by the "make xxx_config" command
***********************************************************************/
#ifndef __CONFIG_H
#define __CONFIG_H
/*-----------------------------------------------------------------------
* High Level Configuration Options
*----------------------------------------------------------------------*/
#define CONFIG_P3Mx /* used for both board versions */
#define CONFIG_SYS_TEXT_BASE 0xfff00000
#if defined (CONFIG_P3M750)
#define CONFIG_750FX /* 750GL/GX/FX */
#define CONFIG_HIGH_BATS /* High BATs supported */
#define CONFIG_SYS_BOARD_NAME "P3M750"
#define CONFIG_SYS_BUS_CLK 100000000
#define CONFIG_SYS_TCLK 100000000
#elif defined (CONFIG_P3M7448)
#define CONFIG_74xx
#define CONFIG_SYS_BOARD_NAME "P3M7448"
#define CONFIG_SYS_BUS_CLK 133333333
#define CONFIG_SYS_TCLK 133333333
#endif
#define CONFIG_SYS_GT_DUAL_CPU /* also for JTAG even with one cpu */
/* which initialization functions to call for this board */
#define CONFIG_SYS_BOARD_ASM_INIT 1
#define CONFIG_BOARD_EARLY_INIT_F 1 /* Call board_early_init_f */
#define CONFIG_MISC_INIT_R 1 /* Call misc_init_r() */
/*-----------------------------------------------------------------------
* Base addresses -- Note these are effective addresses where the
* actual resources get mapped (not physical addresses)
*----------------------------------------------------------------------*/
#define CONFIG_SYS_SDRAM_BASE 0x00000000
#ifdef CONFIG_P3M750
#define CONFIG_SYS_SDRAM1_BASE 0x10000000 /* each 256 MByte */
#endif
#define CONFIG_SYS_MONITOR_LEN (256 << 10) /* Reserve 256 kB for Monitor */
#if defined (CONFIG_P3M750)
#define CONFIG_SYS_FLASH_BASE 0xff800000 /* start of flash banks */
#define CONFIG_SYS_BOOT_SIZE _8M /* boot flash */
#elif defined (CONFIG_P3M7448)
#define CONFIG_SYS_FLASH_BASE 0xff000000 /* start of flash banks */
#define CONFIG_SYS_BOOT_SIZE _16M /* boot flash */
#endif
#define CONFIG_SYS_BOOT_SPACE CONFIG_SYS_FLASH_BASE /* BOOT_CS0 flash 0 */
#define CONFIG_SYS_MONITOR_BASE 0xfff00000
#define CONFIG_SYS_RESET_ADDRESS 0xfff00100
#define CONFIG_SYS_MALLOC_LEN (256 << 10) /* Reserve 256 kB for malloc */
#define CONFIG_SYS_MISC_REGION_BASE 0xf0000000
#define CONFIG_SYS_DFL_GT_REGS 0xf1000000 /* boot time GT_REGS */
#define CONFIG_SYS_GT_REGS 0xf1000000 /* GT Registers are mapped here */
#define CONFIG_SYS_INT_SRAM_BASE 0x42000000 /* GT offers 256k internal SRAM */
/*-----------------------------------------------------------------------
* Initial RAM & stack pointer (placed in internal SRAM)
*----------------------------------------------------------------------*/
/*
* When locking data in cache you should point the CONFIG_SYS_INIT_RAM_ADDRESS
* To an unused memory region. The stack will remain in cache until RAM
* is initialized
*/
#undef CONFIG_SYS_INIT_RAM_LOCK
#define CONFIG_SYS_INIT_RAM_ADDR 0x42000000
#define CONFIG_SYS_INIT_RAM_SIZE 0x1000
#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
/*-----------------------------------------------------------------------
* Serial Port
*----------------------------------------------------------------------*/
#define CONFIG_MPSC /* MV64460 Serial */
#define CONFIG_MPSC_PORT 0
#define CONFIG_BAUDRATE 115200 /* console baudrate */
#define CONFIG_SYS_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200, 230400 }
#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */
#define CONFIG_SYS_LOADS_BAUD_CHANGE 1 /* allow baudrate change */
/*-----------------------------------------------------------------------
* Ethernet
*----------------------------------------------------------------------*/
/* Change the default ethernet port, use this define (options: 0, 1, 2) */
#define CONFIG_SYS_ETH_PORT ETH_0
#define MV_ETH_DEVS 2
#define CONFIG_PHY_RESET 1 /* reset phy upon startup */
#define CONFIG_PHY_GIGE 1 /* Include GbE speed/duplex detection */
/*-----------------------------------------------------------------------
* FLASH related
*----------------------------------------------------------------------*/
#define CONFIG_SYS_FLASH_CFI /* The flash is CFI compatible */
#define CONFIG_FLASH_CFI_DRIVER /* Use common CFI driver */
#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* max number of memory banks */
#define CONFIG_SYS_MAX_FLASH_SECT 512 /* max number of sectors on one chip */
#define CONFIG_SYS_FLASH_ERASE_TOUT 120000 /* Timeout for Flash Erase (in ms) */
#define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Timeout for Flash Write (in ms) */
#define CONFIG_SYS_FLASH_USE_BUFFER_WRITE 1 /* use buffered writes (20x faster) */
#define CONFIG_SYS_FLASH_PROTECTION 1 /* use hardware flash protection */
#define CONFIG_SYS_FLASH_EMPTY_INFO /* print 'E' for empty sector on flinfo */
#define CONFIG_ENV_IS_IN_FLASH 1 /* use FLASH for environment vars */
#if defined (CONFIG_P3M750)
#define CONFIG_ENV_SECT_SIZE 0x20000 /* one sector (1 device) */
#elif defined (CONFIG_P3M7448)
#define CONFIG_ENV_SECT_SIZE 0x40000 /* two sectors (2 devices parallel */
#endif
#define CONFIG_ENV_SIZE 0x2000 /* Total Size of Environment Sector */
#define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE + CONFIG_SYS_MONITOR_LEN)
/*-----------------------------------------------------------------------
* DDR SDRAM
*----------------------------------------------------------------------*/
#define CONFIG_MV64460_ECC
/*-----------------------------------------------------------------------
* I2C
*----------------------------------------------------------------------*/
#define CONFIG_SYS_I2C_SPEED 100000 /* I2C speed default */
/* I2C RTC */
#define CONFIG_RTC_M41T11 1
#define CONFIG_SYS_I2C_RTC_ADDR 0x68
#define CONFIG_SYS_M41T11_BASE_YEAR 1900 /* play along with linux */
/*-----------------------------------------------------------------------
* PCI stuff
*----------------------------------------------------------------------*/
#define PCI_HOST_ADAPTER 0 /* configure ar pci adapter */
#define PCI_HOST_FORCE 1 /* configure as pci host */
#define PCI_HOST_AUTO 2 /* detected via arbiter enable */
#undef CONFIG_PCI /* include pci support */
#ifdef CONFIG_PCI
#define CONFIG_PCI_HOST PCI_HOST_FORCE /* select pci host function */
#define CONFIG_PCI_PNP /* do pci plug-and-play */
#define CONFIG_PCI_SCAN_SHOW /* show devices on bus */
#endif /* CONFIG_PCI */
/* PCI MEMORY MAP section */
#define CONFIG_SYS_PCI0_MEM_BASE 0x80000000
#define CONFIG_SYS_PCI0_MEM_SIZE _128M
#define CONFIG_SYS_PCI1_MEM_BASE 0x88000000
#define CONFIG_SYS_PCI1_MEM_SIZE _128M
#define CONFIG_SYS_PCI0_0_MEM_SPACE (CONFIG_SYS_PCI0_MEM_BASE)
#define CONFIG_SYS_PCI1_0_MEM_SPACE (CONFIG_SYS_PCI1_MEM_BASE)
/* PCI I/O MAP section */
#define CONFIG_SYS_PCI0_IO_BASE 0xfa000000
#define CONFIG_SYS_PCI0_IO_SIZE _16M
#define CONFIG_SYS_PCI1_IO_BASE 0xfb000000
#define CONFIG_SYS_PCI1_IO_SIZE _16M
#define CONFIG_SYS_PCI0_IO_SPACE (CONFIG_SYS_PCI0_IO_BASE)
#define CONFIG_SYS_PCI0_IO_SPACE_PCI 0x00000000
#define CONFIG_SYS_PCI1_IO_SPACE (CONFIG_SYS_PCI1_IO_BASE)
#define CONFIG_SYS_PCI1_IO_SPACE_PCI 0x00000000
#define CONFIG_SYS_ISA_IO_BASE_ADDRESS (CONFIG_SYS_PCI0_IO_BASE)
#define CONFIG_SYS_PCI_IDSEL 0x30
#undef CONFIG_BOOTARGS
#define CONFIG_EXTRA_ENV_SETTINGS_COMMON \
"netdev=eth0\0" \
"nfsargs=setenv bootargs root=/dev/nfs rw " \
"nfsroot=${serverip}:${rootpath}\0" \
"ramargs=setenv bootargs root=/dev/ram rw\0" \
"addip=setenv bootargs ${bootargs} " \
"ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}" \
":${hostname}:${netdev}:off panic=1\0" \
"addtty=setenv bootargs ${bootargs} console=ttyS0,${baudrate}\0"\
"flash_nfs=run nfsargs addip addtty;" \
"bootm ${kernel_addr}\0" \
"flash_self=run ramargs addip addtty;" \
"bootm ${kernel_addr} ${ramdisk_addr}\0" \
"net_nfs=tftp 200000 ${bootfile};run nfsargs addip addtty;" \
"bootm\0" \
"rootpath=/opt/eldk/ppc_6xx\0" \
"u-boot=p3mx/u-boot/u-boot.bin\0" \
"load=tftp 100000 ${u-boot}\0" \
"update=protect off fff00000 fff3ffff;era fff00000 fff3ffff;" \
"cp.b 100000 fff00000 40000;" \
"setenv filesize;saveenv\0" \
"upd=run load update\0" \
"serverip=11.0.0.152\0"
#if defined (CONFIG_P3M750)
#define CONFIG_EXTRA_ENV_SETTINGS \
CONFIG_EXTRA_ENV_SETTINGS_COMMON \
"hostname=p3m750\0" \
"bootfile=/tftpboot/p3mx/vxWorks.st\0" \
"kernel_addr=fc000000\0" \
"ramdisk_addr=fc180000\0" \
"vxfile=p3m750/vxWorks\0" \
"vxuser=ddg\0" \
"vxpass=ddg\0" \
"vxtarget=target\0" \
"vxflags=0x8\0" \
"vxargs=setenv bootargs mgi(0,0)host:${vxfile} h=${serverip} " \
"e=${ipaddr} u=${vxuser} pw=${vxpass} tn=${vxtarget} " \
"f=${vxflags}\0"
#elif defined (CONFIG_P3M7448)
#define CONFIG_EXTRA_ENV_SETTINGS \
CONFIG_EXTRA_ENV_SETTINGS_COMMON \
"hostname=p3m7448\0"
#endif
#if defined (CONFIG_P3M750)
#define CONFIG_BOOTCOMMAND "tftp;run vxargs;bootvx"
#elif defined (CONFIG_P3M7448)
#define CONFIG_BOOTCOMMAND " "
#endif
#define CONFIG_BOOTDELAY 3 /* autoboot after 5 seconds */
/*
* BOOTP options
*/
#define CONFIG_BOOTP_SUBNETMASK
#define CONFIG_BOOTP_GATEWAY
#define CONFIG_BOOTP_HOSTNAME
#define CONFIG_BOOTP_BOOTPATH
#define CONFIG_BOOTP_BOOTFILESIZE
/*
* Command line configuration.
*/
#include <config_cmd_default.h>
#define CONFIG_CMD_ASKENV
#define CONFIG_CMD_DATE
#define CONFIG_CMD_DIAG
#define CONFIG_CMD_ELF
#define CONFIG_CMD_I2C
#define CONFIG_CMD_IRQ
#define CONFIG_CMD_MII
#define CONFIG_CMD_NET
#define CONFIG_CMD_NFS
#define CONFIG_CMD_PING
#define CONFIG_CMD_REGINFO
#define CONFIG_CMD_PCI
#define CONFIG_CMD_CACHE
#define CONFIG_CMD_SDRAM
/*-----------------------------------------------------------------------
* Miscellaneous configurable options
*----------------------------------------------------------------------*/
#define CONFIG_SYS_HUSH_PARSER
#define CONFIG_SYS_LONGHELP /* undef to save memory */
#define CONFIG_SYS_PROMPT "=> " /* Monitor Command Prompt */
#if defined(CONFIG_CMD_KGDB)
#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */
#else
#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */
#endif
#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */
#define CONFIG_SYS_MAXARGS 16 /* max number of command args */
#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */
#define CONFIG_SYS_MEMTEST_START 0x0400000 /* memtest works on */
#define CONFIG_SYS_MEMTEST_END 0x0C00000 /* 4 ... 12 MB in DRAM */
#define CONFIG_SYS_LOAD_ADDR 0x08000000 /* default load address */
#define CONFIG_SYS_HZ 1000 /* decrementer freq: 1 ms ticks */
#define CONFIG_CMDLINE_EDITING 1 /* add command line history */
#define CONFIG_LOOPW 1 /* enable loopw command */
#define CONFIG_MX_CYCLIC 1 /* enable mdc/mwc commands */
#define CONFIG_ZERO_BOOTDELAY_CHECK /* check for keypress on bootdelay==0 */
#define CONFIG_VERSION_VARIABLE 1 /* include version env variable */
/*-----------------------------------------------------------------------
* Marvell MV64460 config settings
*----------------------------------------------------------------------*/
/* Reset values for Port behavior (8bit/ 32bit, etc.) only corrected device width */
#if defined (CONFIG_P3M750)
#define CONFIG_SYS_BOOT_PAR 0x8FDFF87F /* 16 bit flash, disable burst*/
#elif defined (CONFIG_P3M7448)
#define CONFIG_SYS_BOOT_PAR 0x8FEFFFFF /* 32 bit flash, burst enabled */
#endif
/*
* MPP[0] Serial Port 0 TxD TxD OUT Connected to P14 (buffered)
* MPP[1] Serial Port 0 RxD RxD IN Connected to P14 (buffered)
* MPP[2] NC
* MPP[3] Serial Port 1 TxD TxD OUT Connected to P14 (buffered)
* MPP[4] PCI Monarch# GPIO IN Connected to P12
* MPP[5] Serial Port 1 RxD RxD IN Connected to P14 (buffered)
* MPP[6] PMC Carrier Interrupt 0 Int IN Connected to P14
* MPP[7] PMC Carrier Interrupt 1 Int IN Connected to P14
* MPP[8] Reserved Do not use
* MPP[9] Reserved Do not use
* MPP[10] Reserved Do not use
* MPP[11] Reserved Do not use
* MPP[12] Phy 0 Interrupt Int IN
* MPP[13] Phy 1 Interrupt Int IN
* MPP[14] NC
* MPP[15] NC
* MPP[16] PCI Interrupt C Int IN Connected to P11
* MPP[17] PCI Interrupt D Int IN Connected to P11
* MPP[18] Watchdog NMI# GPIO IN Connected to MPP[24]
* MPP[19] Watchdog Expired# WDE OUT Connected to rst logic
* MPP[20] Watchdog Status WD_STS IN Read back of rst by watchdog
* MPP[21] NC
* MPP[22] GP LED Green GPIO OUT
* MPP[23] GP LED Red GPIO OUT
* MPP[24] Watchdog NMI# Int OUT
* MPP[25] NC
* MPP[26] NC
* MPP[27] PCI Interrupt A Int IN Connected to P11
* MPP[28] NC
* MPP[29] PCI Interrupt B Int IN Connected to P11
* MPP[30] Module reset GPIO OUT Board reset
* MPP[31] PCI EReady GPIO IN Connected to P12
*/
#define CONFIG_SYS_MPP_CONTROL_0 0x00303022
#define CONFIG_SYS_MPP_CONTROL_1 0x00000000
#define CONFIG_SYS_MPP_CONTROL_2 0x00004000
#define CONFIG_SYS_MPP_CONTROL_3 0x00000004
#define CONFIG_SYS_GPP_LEVEL_CONTROL 0x280730D0
/*----------------------------------------------------------------------
* Initial BAT mappings
*/
/* NOTES:
* 1) GUARDED and WRITE_THRU not allowed in IBATS
* 2) CACHEINHIBIT and WRITETHROUGH not allowed together in same BAT
*/
/* SDRAM */
#define CONFIG_SYS_IBAT0L (CONFIG_SYS_SDRAM_BASE | BATL_PP_RW | BATL_CACHEINHIBIT)
#define CONFIG_SYS_IBAT0U (CONFIG_SYS_SDRAM_BASE | BATU_BL_256M | BATU_VS | BATU_VP)
#define CONFIG_SYS_DBAT0L (CONFIG_SYS_SDRAM_BASE | BATL_PP_RW | BATL_GUARDEDSTORAGE | BATL_CACHEINHIBIT)
#define CONFIG_SYS_DBAT0U CONFIG_SYS_IBAT0U
/* init ram */
#define CONFIG_SYS_IBAT1L (CONFIG_SYS_INIT_RAM_ADDR | BATL_PP_RW | BATL_MEMCOHERENCE)
#define CONFIG_SYS_IBAT1U (CONFIG_SYS_INIT_RAM_ADDR | BATU_BL_256K | BATU_VS | BATU_VP)
#define CONFIG_SYS_DBAT1L CONFIG_SYS_IBAT1L
#define CONFIG_SYS_DBAT1U CONFIG_SYS_IBAT1U
/* PCI0, PCI1 in one BAT */
#define CONFIG_SYS_IBAT2L BATL_NO_ACCESS
#define CONFIG_SYS_IBAT2U CONFIG_SYS_DBAT2U
#define CONFIG_SYS_DBAT2L (CONFIG_SYS_PCI0_MEM_BASE | BATL_CACHEINHIBIT | BATL_PP_RW | BATL_GUARDEDSTORAGE)
#define CONFIG_SYS_DBAT2U (CONFIG_SYS_PCI0_MEM_BASE | BATU_BL_256M | BATU_VS | BATU_VP)
/* GT regs, bootrom, all the devices, PCI I/O */
#define CONFIG_SYS_IBAT3L (CONFIG_SYS_MISC_REGION_BASE | BATL_CACHEINHIBIT | BATL_PP_RW)
#define CONFIG_SYS_IBAT3U (CONFIG_SYS_MISC_REGION_BASE | BATU_VS | BATU_VP | BATU_BL_256M)
#define CONFIG_SYS_DBAT3L (CONFIG_SYS_MISC_REGION_BASE | BATL_CACHEINHIBIT | BATL_PP_RW | BATL_GUARDEDSTORAGE)
#define CONFIG_SYS_DBAT3U CONFIG_SYS_IBAT3U
#define CONFIG_SYS_IBAT4L (CONFIG_SYS_SDRAM1_BASE | BATL_PP_RW | BATL_CACHEINHIBIT)
#define CONFIG_SYS_IBAT4U (CONFIG_SYS_SDRAM1_BASE | BATU_BL_256M | BATU_VS | BATU_VP)
#define CONFIG_SYS_DBAT4L (CONFIG_SYS_SDRAM1_BASE | BATL_PP_RW | BATL_CACHEINHIBIT | BATL_GUARDEDSTORAGE)
#define CONFIG_SYS_DBAT4U CONFIG_SYS_IBAT4U
/* set rest out of range for Linux !!!!!!!!!!! */
/* IBAT5 and DBAT5 */
#define CONFIG_SYS_IBAT5L (0x20000000 | BATL_PP_RW | BATL_CACHEINHIBIT)
#define CONFIG_SYS_IBAT5U (0x20000000 | BATU_BL_256M | BATU_VS | BATU_VP)
#define CONFIG_SYS_DBAT5L (0x20000000 | BATL_PP_RW | BATL_CACHEINHIBIT | BATL_GUARDEDSTORAGE)
#define CONFIG_SYS_DBAT5U CONFIG_SYS_IBAT5U
/* IBAT6 and DBAT6 */
#define CONFIG_SYS_IBAT6L (0x20000000 | BATL_PP_RW | BATL_CACHEINHIBIT)
#define CONFIG_SYS_IBAT6U (0x20000000 | BATU_BL_256M | BATU_VS | BATU_VP)
#define CONFIG_SYS_DBAT6L (0x20000000 | BATL_PP_RW | BATL_CACHEINHIBIT | BATL_GUARDEDSTORAGE)
#define CONFIG_SYS_DBAT6U CONFIG_SYS_IBAT6U
/* IBAT7 and DBAT7 */
#define CONFIG_SYS_IBAT7L (0x20000000 | BATL_PP_RW | BATL_CACHEINHIBIT)
#define CONFIG_SYS_IBAT7U (0x20000000 | BATU_BL_256M | BATU_VS | BATU_VP)
#define CONFIG_SYS_DBAT7L (0x20000000 | BATL_PP_RW | BATL_CACHEINHIBIT | BATL_GUARDEDSTORAGE)
#define CONFIG_SYS_DBAT7U CONFIG_SYS_IBAT7U
/*
* For booting Linux, the board info and command line data
* have to be in the first 8 MB of memory, since this is
* the maximum mapped by the Linux kernel during initialization.
*/
#define CONFIG_SYS_BOOTMAPSZ (8<<20) /* Initial Memory map for Linux */
#define CONFIG_SYS_VXWORKS_MAC_PTR 0x42010000 /* use some memory in SRAM that's not used!!! */
/*-----------------------------------------------------------------------
* Cache Configuration
*/
#define CONFIG_SYS_CACHELINE_SIZE 32 /* For all MPC74xx CPUs */
#if defined(CONFIG_CMD_KGDB)
#define CONFIG_SYS_CACHELINE_SHIFT 5 /* log base 2 of the above value */
#endif
/*-----------------------------------------------------------------------
* L2CR setup -- make sure this is right for your board!
* look in include/mpc74xx.h for the defines used here
*/
#define CONFIG_SYS_L2
#if defined (CONFIG_750CX) || defined (CONFIG_750FX)
#define L2_INIT 0
#else
#define L2_INIT (L2CR_L2SIZ_2M | L2CR_L2CLK_3 | L2CR_L2RAM_BURST | \
L2CR_L2OH_5 | L2CR_L2CTL | L2CR_L2WT)
#endif
#define L2_ENABLE (L2_INIT | L2CR_L2E)
#ifndef __ASSEMBLY__
#include <../board/Marvell/include/core.h>
#endif
#endif /* __CONFIG_H */