blob: 69ba8bff0606aca86d33939b13a92eeb262b5f60 [file] [log] [blame]
/*
* Copyright 2016 Freescale Semiconductor, Inc.
*
* SPDX-License-Identifier: GPL-2.0+
*/
#ifndef __CONFIG_H
#define __CONFIG_H
#define CONFIG_LS102XA
#define CONFIG_ARMV7_SECURE_BASE OCRAM_BASE_S_ADDR
#define CONFIG_SYS_FSL_CLK
#define CONFIG_BOARD_EARLY_INIT_F
/*
* Size of malloc() pool
*/
#define CONFIG_SYS_MALLOC_LEN (CONFIG_ENV_SIZE + 16 * 1024 * 1024)
#define CONFIG_SYS_INIT_RAM_ADDR OCRAM_BASE_ADDR
#define CONFIG_SYS_INIT_RAM_SIZE OCRAM_SIZE
/* XHCI Support - enabled by default */
#define CONFIG_HAS_FSL_XHCI_USB
#ifdef CONFIG_HAS_FSL_XHCI_USB
#define CONFIG_USB_XHCI_FSL
#define CONFIG_USB_XHCI_DWC3
#define CONFIG_USB_MAX_CONTROLLER_COUNT 1
#define CONFIG_SYS_USB_XHCI_MAX_ROOT_PORTS 2
#endif
#if defined(CONFIG_HAS_FSL_DR_USB) || defined(CONFIG_HAS_FSL_XHCI_USB)
#define CONFIG_USB_STORAGE
#define CONFIG_CMD_EXT2
#endif
/*
* Generic Timer Definitions
*/
#define GENERIC_TIMER_CLK 12500000
#define CONFIG_SYS_CLK_FREQ 100000000
#define CONFIG_DDR_CLK_FREQ 100000000
/*
* DDR: 800 MHz ( 1600 MT/s data rate )
*/
#define DDR_SDRAM_CFG 0x470c0008
#define DDR_CS0_BNDS 0x008000bf
#define DDR_CS0_CONFIG 0x80014302
#define DDR_TIMING_CFG_0 0x50550004
#define DDR_TIMING_CFG_1 0xbcb38c56
#define DDR_TIMING_CFG_2 0x0040d120
#define DDR_TIMING_CFG_3 0x010e1000
#define DDR_TIMING_CFG_4 0x00000001
#define DDR_TIMING_CFG_5 0x03401400
#define DDR_SDRAM_CFG_2 0x00401010
#define DDR_SDRAM_MODE 0x00061c60
#define DDR_SDRAM_MODE_2 0x00180000
#define DDR_SDRAM_INTERVAL 0x18600618
#define DDR_DDR_WRLVL_CNTL 0x8655f605
#define DDR_DDR_WRLVL_CNTL_2 0x05060607
#define DDR_DDR_WRLVL_CNTL_3 0x05050505
#define DDR_DDR_CDR1 0x80040000
#define DDR_DDR_CDR2 0x00000001
#define DDR_SDRAM_CLK_CNTL 0x02000000
#define DDR_DDR_ZQ_CNTL 0x89080600
#define DDR_CS0_CONFIG_2 0
#define DDR_SDRAM_CFG_MEM_EN 0x80000000
#define SDRAM_CFG2_D_INIT 0x00000010
#define DDR_CDR2_VREF_TRAIN_EN 0x00000080
#define SDRAM_CFG2_FRC_SR 0x80000000
#define SDRAM_CFG_BI 0x00000001
#ifdef CONFIG_RAMBOOT_PBL
#define CONFIG_SYS_FSL_PBL_PBI \
board/freescale/ls1021aiot/ls102xa_pbi.cfg
#endif
#ifdef CONFIG_SD_BOOT
#define CONFIG_SYS_FSL_PBL_RCW \
board/freescale/ls1021aiot/ls102xa_rcw_sd.cfg
#define CONFIG_SPL_FRAMEWORK
#define CONFIG_SPL_LDSCRIPT "arch/$(ARCH)/cpu/u-boot-spl.lds"
#define CONFIG_SPL_LIBCOMMON_SUPPORT
#define CONFIG_SPL_LIBGENERIC_SUPPORT
#define CONFIG_SPL_ENV_SUPPORT
#define CONFIG_SPL_MPC8XXX_INIT_DDR_SUPPORT
#define CONFIG_SPL_I2C_SUPPORT
#define CONFIG_SPL_WATCHDOG_SUPPORT
#define CONFIG_SPL_SERIAL_SUPPORT
#define CONFIG_SPL_MMC_SUPPORT
#define CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_SECTOR 0xe8
#define CONFIG_SPL_TEXT_BASE 0x10000000
#define CONFIG_SPL_MAX_SIZE 0x1a000
#define CONFIG_SPL_STACK 0x1001d000
#define CONFIG_SPL_PAD_TO 0x1c000
#define CONFIG_SYS_TEXT_BASE 0x82000000
#define CONFIG_SYS_SPL_MALLOC_START (CONFIG_SYS_TEXT_BASE + \
CONFIG_SYS_MONITOR_LEN)
#define CONFIG_SYS_SPL_MALLOC_SIZE 0x100000
#define CONFIG_SPL_BSS_START_ADDR 0x80100000
#define CONFIG_SPL_BSS_MAX_SIZE 0x80000
#define CONFIG_SYS_MONITOR_LEN 0x80000
#define CONFIG_SYS_NO_FLASH
#endif
#ifdef CONFIG_QSPI_BOOT
#define CONFIG_SYS_TEXT_BASE 0x40010000
#endif
#if defined(CONFIG_QSPI_BOOT) || defined(CONFIG_SD_BOOT_QSPI)
#define CONFIG_SYS_NO_FLASH
#endif
#define CONFIG_NR_DRAM_BANKS 1
#define CONFIG_SYS_DDR_SDRAM_BASE 0x80000000UL
#define CONFIG_SYS_SDRAM_BASE CONFIG_SYS_DDR_SDRAM_BASE
#define CONFIG_FSL_CAAM /* Enable CAAM */
/*
* Serial Port
*/
#define CONFIG_CONS_INDEX 1
#define CONFIG_SYS_NS16550_SERIAL
#define CONFIG_SYS_NS16550_REG_SIZE 1
#define CONFIG_SYS_NS16550_CLK get_serial_clock()
#define CONFIG_BAUDRATE 115200
/*
* I2C
*/
#define CONFIG_CMD_I2C
#define CONFIG_SYS_I2C
#define CONFIG_SYS_I2C_MXC
#define CONFIG_SYS_I2C_MXC_I2C1 /* enable I2C bus 1 */
#define CONFIG_SYS_I2C_MXC_I2C2 /* enable I2C bus 2 */
#define CONFIG_SYS_I2C_MXC_I2C3 /* enable I2C bus 3 */
/* EEPROM */
#define CONFIG_ID_EEPROM
#define CONFIG_SYS_I2C_EEPROM_NXID
#define CONFIG_SYS_EEPROM_BUS_NUM 0
#define CONFIG_SYS_I2C_EEPROM_ADDR 0x51
#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 2
/*
* MMC
*/
#define CONFIG_CMD_MMC
#define CONFIG_FSL_ESDHC
#define CONFIG_GENERIC_MMC
/* SATA */
#define CONFIG_CMD_SCSI
#define CONFIG_LIBATA
#define CONFIG_SCSI_AHCI
#define CONFIG_SCSI_AHCI_PLAT
#ifndef PCI_DEVICE_ID_FREESCALE_AHCI
#define PCI_DEVICE_ID_FREESCALE_AHCI 0x0440
#endif
#define CONFIG_SCSI_DEV_LIST {PCI_VENDOR_ID_FREESCALE, \
PCI_DEVICE_ID_FREESCALE_AHCI}
#define CONFIG_SYS_SCSI_MAX_SCSI_ID 1
#define CONFIG_SYS_SCSI_MAX_LUN 1
#define CONFIG_SYS_SCSI_MAX_DEVICE (CONFIG_SYS_SCSI_MAX_SCSI_ID * \
CONFIG_SYS_SCSI_MAX_LUN)
#define CONFIG_CMD_FAT
#define CONFIG_DOS_PARTITION
#define CONFIG_PARTITION_UUIDS
#define CONFIG_EFI_PARTITION
#define CONFIG_CMD_GPT
/* SPI */
#if defined(CONFIG_QSPI_BOOT) || defined(CONFIG_SD_BOOT_QSPI)
#define CONFIG_SPI_FLASH_SPANSION
/* QSPI */
#define QSPI0_AMBA_BASE 0x40000000
#define FSL_QSPI_FLASH_SIZE (1 << 24)
#define FSL_QSPI_FLASH_NUM 2
#define CONFIG_SPI_FLASH_BAR
#define CONFIG_SPI_FLASH_SPANSION
#endif
/* DM SPI */
#if defined(CONFIG_FSL_DSPI) || defined(CONFIG_FSL_QSPI)
#define CONFIG_CMD_SF
#define CONFIG_DM_SPI_FLASH
#endif
/*
* eTSEC
*/
#define CONFIG_TSEC_ENET
#ifdef CONFIG_TSEC_ENET
#define CONFIG_MII
#define CONFIG_MII_DEFAULT_TSEC 1
#define CONFIG_TSEC1 1
#define CONFIG_TSEC1_NAME "eTSEC1"
#define CONFIG_TSEC2 1
#define CONFIG_TSEC2_NAME "eTSEC2"
#define TSEC1_PHY_ADDR 1
#define TSEC2_PHY_ADDR 3
#define TSEC1_FLAGS (TSEC_GIGABIT | TSEC_REDUCED)
#define TSEC2_FLAGS (TSEC_GIGABIT | TSEC_REDUCED)
#define TSEC1_PHYIDX 0
#define TSEC2_PHYIDX 0
#define CONFIG_ETHPRIME "eTSEC2"
#define CONFIG_PHY_GIGE
#define CONFIG_PHYLIB
#define CONFIG_PHY_ATHEROS
#define CONFIG_HAS_ETH0
#define CONFIG_HAS_ETH1
#define CONFIG_HAS_ETH2
#endif
/* PCIe */
#define CONFIG_PCIE1 /* PCIE controler 1 */
#define CONFIG_PCIE2 /* PCIE controler 2 */
#define FSL_PCIE_COMPAT "fsl,ls1021a-pcie"
#ifdef CONFIG_PCI
#define CONFIG_PCI_SCAN_SHOW
#define CONFIG_CMD_PCI
#endif
#define CONFIG_CMD_PING
#define CONFIG_CMD_DHCP
#define CONFIG_CMD_MII
#define CONFIG_CMDLINE_TAG
#define CONFIG_CMDLINE_EDITING
#if defined(CONFIG_QSPI_BOOT) || defined(CONFIG_SD_BOOT)
#undef CONFIG_CMD_IMLS
#endif
#define CONFIG_PEN_ADDR_BIG_ENDIAN
#define CONFIG_LAYERSCAPE_NS_ACCESS
#define CONFIG_SMP_PEN_ADDR 0x01ee0200
#define CONFIG_TIMER_CLK_FREQ 12500000
#define CONFIG_HWCONFIG
#define HWCONFIG_BUFFER_SIZE 256
#define CONFIG_FSL_DEVICE_DISABLE
#define CONFIG_EXTRA_ENV_SETTINGS \
"bootargs=root=/dev/ram0 rw console=ttyS0,115200\0" \
"initrd_high=0xffffffff\0" \
"fdt_high=0xffffffff\0"
/*
* Miscellaneous configurable options
*/
#define CONFIG_SYS_LONGHELP /* undef to save memory */
#define CONFIG_SYS_PROMPT_HUSH_PS2 "> "
#define CONFIG_AUTO_COMPLETE
#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */
#define CONFIG_SYS_PBSIZE \
(CONFIG_SYS_CBSIZE + sizeof(CONFIG_SYS_PROMPT) + 16)
#define CONFIG_SYS_MAXARGS 16 /* max number of command args */
#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE
#define CONFIG_CMD_GREPENV
#define CONFIG_CMD_MEMINFO
#define CONFIG_SYS_LOAD_ADDR 0x82000000
#define CONFIG_LS102XA_STREAM_ID
/*
* Stack sizes
* The stack sizes are set up in start.S using the settings below
*/
#define CONFIG_STACKSIZE (30 * 1024)
#define CONFIG_SYS_INIT_SP_OFFSET \
(CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
#define CONFIG_SYS_INIT_SP_ADDR \
(CONFIG_SYS_INIT_RAM_ADDR + CONFIG_SYS_INIT_SP_OFFSET)
#ifdef CONFIG_SPL_BUILD
#define CONFIG_SYS_MONITOR_BASE CONFIG_SPL_TEXT_BASE
#else
/* start of monitor */
#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE
#endif
#define CONFIG_SYS_QE_FW_ADDR 0x67f40000
/*
* Environment
*/
#define CONFIG_ENV_OVERWRITE
#if defined(CONFIG_SD_BOOT)
#define CONFIG_ENV_OFFSET 0x100000
#define CONFIG_ENV_IS_IN_MMC
#define CONFIG_SYS_MMC_ENV_DEV 0
#define CONFIG_ENV_SIZE 0x2000
#elif defined(CONFIG_QSPI_BOOT)
#define CONFIG_ENV_IS_IN_SPI_FLASH
#define CONFIG_ENV_SIZE 0x2000
#define CONFIG_ENV_OFFSET 0x100000
#define CONFIG_ENV_SECT_SIZE 0x10000
#endif
#define CONFIG_OF_BOARD_SETUP
#define CONFIG_OF_STDOUT_VIA_ALIAS
#define CONFIG_CMD_BOOTZ
#define CONFIG_MISC_INIT_R
/* Hash command with SHA acceleration supported in hardware */
#ifdef CONFIG_FSL_CAAM
#define CONFIG_CMD_HASH
#define CONFIG_SHA_HW_ACCEL
#endif
#include <asm/fsl_secure_boot.h>
#endif