blob: 1763f97b65e10cc12749cfa0af6f3b42bc8fc4fe [file] [log] [blame]
/*
* Configuation settings for the Motorola MC5282EVB board.
*
* (C) Copyright 2003 Josef Baumgartner <josef.baumgartner@telex.de>
*
* See file CREDITS for list of people who contributed to this
* project.
*
* This program is free software; you can redistribute it and/or
* modify it under the terms of the GNU General Public License as
* published by the Free Software Foundation; either version 2 of
* the License, or (at your option) any later version.
*
* This program is distributed in the hope that it will be useful,
* but WITHOUT ANY WARRANTY; without even the implied warranty of
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
* GNU General Public License for more details.
*
* You should have received a copy of the GNU General Public License
* along with this program; if not, write to the Free Software
* Foundation, Inc., 59 Temple Place, Suite 330, Boston,
* MA 02111-1307 USA
*/
/*
* board/config.h - configuration options, board specific
*/
#ifndef _CONFIG_M5282EVB_H
#define _CONFIG_M5282EVB_H
/*
* High Level Configuration Options
* (easy to change)
*/
#define CONFIG_MCF52x2 /* define processor family */
#define CONFIG_M5282 /* define processor type */
#define CONFIG_MCFTMR
#define CONFIG_MCFUART
#define CFG_UART_PORT (0)
#define CONFIG_BAUDRATE 115200
#define CFG_BAUDRATE_TABLE { 9600 , 19200 , 38400 , 57600, 115200 }
#undef CONFIG_MONITOR_IS_IN_RAM /* define if monitor is started from a pre-loader */
/* Configuration for environment
* Environment is embedded in u-boot in the second sector of the flash
*/
#define CFG_ENV_ADDR 0xffe04000
#define CFG_ENV_SIZE 0x2000
#define CONFIG_ENV_IS_IN_FLASH 1
/*
* BOOTP options
*/
#define CONFIG_BOOTP_BOOTFILESIZE
#define CONFIG_BOOTP_BOOTPATH
#define CONFIG_BOOTP_GATEWAY
#define CONFIG_BOOTP_HOSTNAME
/*
* Command line configuration.
*/
#include <config_cmd_default.h>
#define CONFIG_CMD_NET
#define CONFIG_CMD_PING
#define CONFIG_CMD_MII
#undef CONFIG_CMD_LOADS
#undef CONFIG_CMD_LOADB
#define CONFIG_MCFFEC
#ifdef CONFIG_MCFFEC
# define CONFIG_NET_MULTI 1
# define CONFIG_MII 1
# define CONFIG_MII_INIT 1
# define CFG_DISCOVER_PHY
# define CFG_RX_ETH_BUFFER 8
# define CFG_FAULT_ECHO_LINK_DOWN
# define CFG_FEC0_PINMUX 0
# define CFG_FEC0_MIIBASE CFG_FEC0_IOBASE
# define MCFFEC_TOUT_LOOP 50000
/* If CFG_DISCOVER_PHY is not defined - hardcoded */
# ifndef CFG_DISCOVER_PHY
# define FECDUPLEX FULL
# define FECSPEED _100BASET
# else
# ifndef CFG_FAULT_ECHO_LINK_DOWN
# define CFG_FAULT_ECHO_LINK_DOWN
# endif
# endif /* CFG_DISCOVER_PHY */
#endif
#define CONFIG_BOOTDELAY 5
#ifdef CONFIG_MCFFEC
# define CONFIG_ETHADDR 00:e0:0c:bc:e5:60
# define CONFIG_IPADDR 192.162.1.2
# define CONFIG_NETMASK 255.255.255.0
# define CONFIG_SERVERIP 192.162.1.1
# define CONFIG_GATEWAYIP 192.162.1.1
# define CONFIG_OVERWRITE_ETHADDR_ONCE
#endif /* CONFIG_MCFFEC */
#define CONFIG_HOSTNAME M5282EVB
#define CONFIG_EXTRA_ENV_SETTINGS \
"netdev=eth0\0" \
"loadaddr=10000\0" \
"u-boot=u-boot.bin\0" \
"load=tftp ${loadaddr) ${u-boot}\0" \
"upd=run load; run prog\0" \
"prog=prot off ffe00000 ffe3ffff;" \
"era ffe00000 ffe3ffff;" \
"cp.b ${loadaddr} ffe00000 ${filesize};"\
"save\0" \
""
#define CFG_PROMPT "-> "
#define CFG_LONGHELP /* undef to save memory */
#if defined(CONFIG_CMD_KGDB)
#define CFG_CBSIZE 1024 /* Console I/O Buffer Size */
#else
#define CFG_CBSIZE 256 /* Console I/O Buffer Size */
#endif
#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */
#define CFG_MAXARGS 16 /* max number of command args */
#define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */
#define CFG_LOAD_ADDR 0x20000
#define CFG_MEMTEST_START 0x400
#define CFG_MEMTEST_END 0x380000
#define CFG_HZ 1000
#define CFG_CLK 64000000
/* PLL Configuration: Ext Clock * 6 (see table 9-4 of MCF user manual) */
#define CFG_MFD 0x02 /* PLL Multiplication Factor Devider */
#define CFG_RFD 0x00 /* PLL Reduce Frecuency Devider */
/*
* Low Level Configuration Settings
* (address mappings, register initial values, etc.)
* You should know what you are doing if you make changes here.
*/
#define CFG_MBAR 0x40000000
/*-----------------------------------------------------------------------
* Definitions for initial stack pointer and data area (in DPRAM)
*/
#define CFG_INIT_RAM_ADDR 0x20000000
#define CFG_INIT_RAM_END 0x10000 /* End of used area in internal SRAM */
#define CFG_GBL_DATA_SIZE 64 /* size in bytes reserved for initial data */
#define CFG_GBL_DATA_OFFSET (CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE)
#define CFG_INIT_SP_OFFSET CFG_GBL_DATA_OFFSET
/*-----------------------------------------------------------------------
* Start addresses for the final memory configuration
* (Set up by the startup code)
* Please note that CFG_SDRAM_BASE _must_ start at 0
*/
#define CFG_SDRAM_BASE 0x00000000
#define CFG_SDRAM_SIZE 16 /* SDRAM size in MB */
#define CFG_FLASH_BASE 0xffe00000
#define CFG_INT_FLASH_BASE 0xf0000000
#define CFG_INT_FLASH_ENABLE 0x21
/* If M5282 port is fully implemented the monitor base will be behind
* the vector table. */
#if (TEXT_BASE != CFG_INT_FLASH_BASE)
#define CFG_MONITOR_BASE (CFG_FLASH_BASE + 0x400)
#else
#define CFG_MONITOR_BASE (TEXT_BASE + 0x418) /* 24 Byte for CFM-Config */
#endif
#define CFG_MONITOR_LEN 0x20000
#define CFG_MALLOC_LEN (256 << 10)
#define CFG_BOOTPARAMS_LEN 64*1024
/*
* For booting Linux, the board info and command line data
* have to be in the first 8 MB of memory, since this is
* the maximum mapped by the Linux kernel during initialization ??
*/
#define CFG_BOOTMAPSZ (CFG_SDRAM_BASE + (CFG_SDRAM_SIZE << 20))
/*-----------------------------------------------------------------------
* FLASH organization
*/
#define CFG_FLASH_CFI
#ifdef CFG_FLASH_CFI
# define CONFIG_FLASH_CFI_DRIVER 1
# define CFG_FLASH_SIZE 0x1000000 /* Max size that the board might have */
# define CFG_FLASH_CFI_WIDTH FLASH_CFI_16BIT
# define CFG_MAX_FLASH_BANKS 1 /* max number of memory banks */
# define CFG_MAX_FLASH_SECT 137 /* max number of sectors on one chip */
# define CFG_FLASH_PROTECTION /* "Real" (hardware) sectors protection */
# define CFG_FLASH_CHECKSUM
# define CFG_FLASH_BANKS_LIST { CFG_FLASH_BASE }
#endif
/*-----------------------------------------------------------------------
* Cache Configuration
*/
#define CFG_CACHELINE_SIZE 16
/*-----------------------------------------------------------------------
* Memory bank definitions
*/
#define CFG_CS0_BASE CFG_FLASH_BASE
#define CFG_CS0_SIZE 2*1024*1024
#define CFG_CS0_WIDTH 16
#define CFG_CS0_RO 0
#define CFG_CS0_WS 6
/*
#define CFG_CS3_BASE 0xE0000000
#define CFG_CS3_SIZE 1*1024*1024
#define CFG_CS3_WIDTH 16
#define CFG_CS3_RO 0
#define CFG_CS3_WS 6
*/
/*-----------------------------------------------------------------------
* Port configuration
*/
#define CFG_PACNT 0x0000000 /* Port A D[31:24] */
#define CFG_PADDR 0x0000000
#define CFG_PADAT 0x0000000
#define CFG_PBCNT 0x0000000 /* Port B D[23:16] */
#define CFG_PBDDR 0x0000000
#define CFG_PBDAT 0x0000000
#define CFG_PCCNT 0x0000000 /* Port C D[15:08] */
#define CFG_PCDDR 0x0000000
#define CFG_PCDAT 0x0000000
#define CFG_PDCNT 0x0000000 /* Port D D[07:00] */
#define CFG_PCDDR 0x0000000
#define CFG_PCDAT 0x0000000
#define CFG_PEHLPAR 0xC0
#define CFG_PUAPAR 0x0F /* UA0..UA3 = Uart 0 +1 */
#define CFG_DDRUA 0x05
#define CFG_PJPAR 0xFF;
#endif /* _CONFIG_M5282EVB_H */