blob: 0d47d70fd13813a2fca557df5ec10eca75c503c5 [file] [log] [blame]
/*
* (C) Copyright 2005
* Wolfgang Denk, DENX Software Engineering, wd@denx.de.
*
* See file CREDITS for list of people who contributed to this
* project.
*
* This program is free software; you can redistribute it and/or
* modify it under the terms of the GNU General Public License as
* published by the Free Software Foundation; either version 2 of
* the License, or (at your option) any later version.
*
* This program is distributed in the hope that it will be useful,
* but WITHOUT ANY WARRANTY; without even the implied warranty of
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
* GNU General Public License for more details.
*
* You should have received a copy of the GNU General Public License
* along with this program; if not, write to the Free Software
* Foundation, Inc., 59 Temple Place, Suite 330, Boston,
* MA 02111-1307 USA
*/
/*
* TQM8349 board configuration file
*/
#ifndef __CONFIG_H
#define __CONFIG_H
/*
* High Level Configuration Options
*/
#define CONFIG_E300 1 /* E300 Family */
#define CONFIG_MPC83XX 1 /* MPC83XX family */
#define CONFIG_MPC834X 1 /* MPC834X specific */
#define CONFIG_MPC8349 1 /* MPC8349 specific */
#define CONFIG_TQM834X 1 /* TQM834X board specific */
/* IMMR Base Addres Register, use Freescale default: 0xff400000 */
#define CFG_IMMR 0xff400000
/* System clock. Primary input clock when in PCI host mode */
#define CONFIG_83XX_CLKIN 66666000 /* 66,666 MHz */
/*
* Local Bus LCRR
* LCRR: DLL bypass, Clock divider is 8
*
* for CSB = 266 MHz it gives LCB clock frequency = 33 MHz
*
* External Local Bus rate is
* CLKIN * HRCWL_CSB_TO_CLKIN / HRCWL_LCL_BUS_TO_SCB_CLK / LCRR_CLKDIV
*/
#define CFG_LCRR (LCRR_DBYP | LCRR_CLKDIV_8)
/* board pre init: do not call, nothing to do */
#undef CONFIG_BOARD_EARLY_INIT_F
/* detect the number of flash banks */
#define CONFIG_BOARD_EARLY_INIT_R
/*
* DDR Setup
*/
#define CFG_DDR_BASE 0x00000000 /* DDR is system memory*/
#define CFG_SDRAM_BASE CFG_DDR_BASE
#define CFG_DDR_SDRAM_BASE CFG_DDR_BASE
#define DDR_CASLAT_25 /* CASLAT set to 2.5 */
#undef CONFIG_DDR_ECC /* only for ECC DDR module */
#undef CONFIG_SPD_EEPROM /* do not use SPD EEPROM for DDR setup */
#undef CFG_DRAM_TEST /* memory test, takes time */
#define CFG_MEMTEST_START 0x00000000 /* memtest region */
#define CFG_MEMTEST_END 0x00100000
/*
* FLASH on the Local Bus
*/
#define CFG_FLASH_CFI /* use the Common Flash Interface */
#define CONFIG_FLASH_CFI_DRIVER /* use the CFI driver */
#undef CFG_FLASH_CHECKSUM
#define CFG_FLASH_BASE 0x80000000 /* start of FLASH */
#define CFG_FLASH_SIZE 8 /* FLASH size in MB */
/* buffered writes in the AMD chip set is not supported yet */
#undef CFG_FLASH_USE_BUFFER_WRITE
/*
* FLASH bank number detection
*/
/*
* When CFG_MAX_FLASH_BANKS_DETECT is defined, the actual number of Flash
* banks has to be determined at runtime and stored in a gloabl variable
* tqm834x_num_flash_banks. The value of CFG_MAX_FLASH_BANKS_DETECT is only
* used instead of CFG_MAX_FLASH_BANKS to allocate the array flash_info, and
* should be made sufficiently large to accomodate the number of banks that
* might actually be detected. Since most (all?) Flash related functions use
* CFG_MAX_FLASH_BANKS as the number of actual banks on the board, it is
* defined as tqm834x_num_flash_banks.
*/
#define CFG_MAX_FLASH_BANKS_DETECT 2
#ifndef __ASSEMBLY__
extern int tqm834x_num_flash_banks;
#endif
#define CFG_MAX_FLASH_BANKS (tqm834x_num_flash_banks)
#define CFG_MAX_FLASH_SECT 512 /* max sectors per device */
/* 32 bit device at 0x80000000 via GPCM (0x8000_1801) */
#define CFG_BR0_PRELIM ((CFG_FLASH_BASE & BR_BA) | \
BR_MS_GPCM | BR_PS_32 | BR_V)
/* FLASH timing (0x0000_0c54) */
#define CFG_OR_TIMING_FLASH (OR_GPCM_CSNT | OR_GPCM_ACS_DIV4 | \
OR_GPCM_SCY_5 | OR_GPCM_TRLX)
#define CFG_PRELIM_OR_AM 0xc0000000 /* OR addr mask: 1 GiB */
#define CFG_OR0_PRELIM (CFG_PRELIM_OR_AM | CFG_OR_TIMING_FLASH)
#define CFG_LBLAWAR0_PRELIM 0x8000001D /* 1 GiB window size (2^(size + 1)) */
#define CFG_LBLAWBAR0_PRELIM CFG_FLASH_BASE /* Window base at flash base */
/* disable remaining mappings */
#define CFG_BR1_PRELIM 0x00000000
#define CFG_OR1_PRELIM 0x00000000
#define CFG_LBLAWBAR1_PRELIM 0x00000000
#define CFG_LBLAWAR1_PRELIM 0x00000000
#define CFG_BR2_PRELIM 0x00000000
#define CFG_OR2_PRELIM 0x00000000
#define CFG_LBLAWBAR2_PRELIM 0x00000000
#define CFG_LBLAWAR2_PRELIM 0x00000000
#define CFG_BR3_PRELIM 0x00000000
#define CFG_OR3_PRELIM 0x00000000
#define CFG_LBLAWBAR3_PRELIM 0x00000000
#define CFG_LBLAWAR3_PRELIM 0x00000000
#define CFG_BR4_PRELIM 0x00000000
#define CFG_OR4_PRELIM 0x00000000
#define CFG_LBLAWBAR4_PRELIM 0x00000000
#define CFG_LBLAWAR4_PRELIM 0x00000000
#define CFG_BR5_PRELIM 0x00000000
#define CFG_OR5_PRELIM 0x00000000
#define CFG_LBLAWBAR5_PRELIM 0x00000000
#define CFG_LBLAWAR5_PRELIM 0x00000000
#define CFG_BR6_PRELIM 0x00000000
#define CFG_OR6_PRELIM 0x00000000
#define CFG_LBLAWBAR6_PRELIM 0x00000000
#define CFG_LBLAWAR6_PRELIM 0x00000000
#define CFG_BR7_PRELIM 0x00000000
#define CFG_OR7_PRELIM 0x00000000
#define CFG_LBLAWBAR7_PRELIM 0x00000000
#define CFG_LBLAWAR7_PRELIM 0x00000000
/*
* Monitor config
*/
#define CFG_MONITOR_BASE TEXT_BASE /* start of monitor */
#if (CFG_MONITOR_BASE < CFG_FLASH_BASE)
#define CFG_RAMBOOT
#else
#undef CFG_RAMBOOT
#endif
#define CONFIG_L1_INIT_RAM
#define CFG_INIT_RAM_LOCK 1
#define CFG_INIT_RAM_ADDR 0x20000000 /* Initial RAM address */
#define CFG_INIT_RAM_END 0x1000 /* End of used area in RAM*/
#define CFG_GBL_DATA_SIZE 0x100 /* num bytes initial data */
#define CFG_GBL_DATA_OFFSET (CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE)
#define CFG_INIT_SP_OFFSET CFG_GBL_DATA_OFFSET
#define CFG_MONITOR_LEN (256 * 1024) /* Reserve 256 kB for Mon */
#define CFG_MALLOC_LEN (256 * 1024) /* Reserve 256 kB for malloc */
/*
* Serial Port
*/
#define CONFIG_CONS_INDEX 1
#undef CONFIG_SERIAL_SOFTWARE_FIFO
#define CFG_NS16550
#define CFG_NS16550_SERIAL
#define CFG_NS16550_REG_SIZE 1
#define CFG_NS16550_CLK get_bus_freq(0)
#define CFG_BAUDRATE_TABLE \
{300, 600, 1200, 2400, 4800, 9600, 19200, 38400,115200}
#define CFG_NS16550_COM1 (CFG_IMMR + 0x4500)
#define CFG_NS16550_COM2 (CFG_IMMR + 0x4600)
/*
* I2C
*/
#define CONFIG_HARD_I2C /* I2C with hardware support */
#undef CONFIG_SOFT_I2C /* I2C bit-banged */
#define CONFIG_FSL_I2C
#define CFG_I2C_SPEED 400000 /* I2C speed: 400KHz */
#define CFG_I2C_SLAVE 0x7F /* slave address */
#define CFG_I2C_OFFSET 0x3000
/* I2C EEPROM, configuration for onboard EEPROMs 24C256 and 24C32 */
#define CFG_I2C_EEPROM_ADDR 0x50 /* 1010000x */
#define CFG_I2C_EEPROM_ADDR_LEN 2 /* 16 bit */
#define CFG_EEPROM_PAGE_WRITE_BITS 5 /* 32 bytes per write */
#define CFG_EEPROM_PAGE_WRITE_ENABLE
#define CFG_EEPROM_PAGE_WRITE_DELAY_MS 12 /* 10ms +/- 20% */
#define CFG_I2C_MULTI_EEPROMS 1 /* more than one eeprom */
/* I2C RTC */
#define CONFIG_RTC_DS1337 /* use ds1337 rtc via i2c */
#define CFG_I2C_RTC_ADDR 0x68 /* at address 0x68 */
/* I2C SYSMON (LM75) */
#define CONFIG_DTT_LM75 1 /* ON Semi's LM75 */
#define CONFIG_DTT_SENSORS {0} /* Sensor addresses */
#define CFG_DTT_MAX_TEMP 70
#define CFG_DTT_LOW_TEMP -30
#define CFG_DTT_HYSTERESIS 3
/*
* TSEC
*/
#define CONFIG_TSEC_ENET /* tsec ethernet support */
#define CONFIG_MII
#define CFG_TSEC1_OFFSET 0x24000
#define CFG_TSEC1 (CFG_IMMR + CFG_TSEC1_OFFSET)
#define CFG_TSEC2_OFFSET 0x25000
#define CFG_TSEC2 (CFG_IMMR + CFG_TSEC2_OFFSET)
#if defined(CONFIG_TSEC_ENET)
#ifndef CONFIG_NET_MULTI
#define CONFIG_NET_MULTI
#endif
#define CONFIG_TSEC1 1
#define CONFIG_TSEC1_NAME "TSEC0"
#define CONFIG_TSEC2 1
#define CONFIG_TSEC2_NAME "TSEC1"
#define TSEC1_PHY_ADDR 2
#define TSEC2_PHY_ADDR 1
#define TSEC1_PHYIDX 0
#define TSEC2_PHYIDX 0
#define TSEC1_FLAGS TSEC_GIGABIT
#define TSEC2_FLAGS TSEC_GIGABIT
/* Options are: TSEC[0-1] */
#define CONFIG_ETHPRIME "TSEC0"
#endif /* CONFIG_TSEC_ENET */
/*
* General PCI
* Addresses are mapped 1-1.
*/
#define CONFIG_PCI
#if defined(CONFIG_PCI)
#define CONFIG_PCI_PNP /* do pci plug-and-play */
#define CONFIG_PCI_SCAN_SHOW /* show pci devices on startup */
/* PCI1 host bridge */
#define CFG_PCI1_MEM_BASE 0xc0000000
#define CFG_PCI1_MEM_PHYS CFG_PCI1_MEM_BASE
#define CFG_PCI1_MEM_SIZE 0x20000000 /* 512M */
#define CFG_PCI1_IO_BASE 0xe2000000
#define CFG_PCI1_IO_PHYS CFG_PCI1_IO_BASE
#define CFG_PCI1_IO_SIZE 0x1000000 /* 16M */
#undef CONFIG_EEPRO100
#define CONFIG_EEPRO100
#undef CONFIG_TULIP
#if !defined(CONFIG_PCI_PNP)
#define PCI_ENET0_IOADDR CFG_PCI1_IO_BASE
#define PCI_ENET0_MEMADDR CFG_PCI1_MEM_BASE
#define PCI_IDSEL_NUMBER 0x1c /* slot0 (IDSEL) = 28 */
#endif
#define CFG_PCI_SUBSYS_VENDORID 0x1957 /* Freescale */
#endif /* CONFIG_PCI */
/*
* Environment
*/
#define CONFIG_ENV_OVERWRITE
#ifndef CFG_RAMBOOT
#define CONFIG_ENV_IS_IN_FLASH 1
#define CFG_ENV_ADDR (CFG_MONITOR_BASE + 0x40000)
#define CFG_ENV_SECT_SIZE 0x40000 /* 256K(one sector) for env */
#define CFG_ENV_SIZE 0x2000
#else
#define CFG_NO_FLASH 1 /* Flash is not usable now */
#define CONFIG_ENV_IS_NOWHERE 1 /* Store ENV in memory only */
#define CFG_ENV_ADDR (CFG_MONITOR_BASE - 0x1000)
#define CFG_ENV_SIZE 0x2000
#endif
#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */
#define CFG_LOADS_BAUD_CHANGE 1 /* allow baudrate change */
/*
* BOOTP options
*/
#define CONFIG_BOOTP_BOOTFILESIZE
#define CONFIG_BOOTP_BOOTPATH
#define CONFIG_BOOTP_GATEWAY
#define CONFIG_BOOTP_HOSTNAME
/*
* Command line configuration.
*/
#include <config_cmd_default.h>
#define CONFIG_CMD_DATE
#define CONFIG_CMD_DTT
#define CONFIG_CMD_EEPROM
#define CONFIG_CMD_I2C
#define CONFIG_CMD_JFFS2
#define CONFIG_CMD_MII
#define CONFIG_CMD_PING
#define CONFIG_CMD_DHCP
#if defined(CONFIG_PCI)
#define CONFIG_CMD_PCI
#endif
#if defined(CFG_RAMBOOT)
#undef CONFIG_CMD_ENV
#undef CONFIG_CMD_LOADS
#endif
/*
* Miscellaneous configurable options
*/
#define CFG_LONGHELP /* undef to save memory */
#define CFG_LOAD_ADDR 0x2000000 /* default load address */
#define CFG_PROMPT "=> " /* Monitor Command Prompt */
#define CONFIG_CMDLINE_EDITING 1 /* add command line history */
#define CFG_HUSH_PARSER 1 /* Use the HUSH parser */
#ifdef CFG_HUSH_PARSER
#define CFG_PROMPT_HUSH_PS2 "> "
#endif
#if defined(CONFIG_CMD_KGDB)
#define CFG_CBSIZE 1024 /* Console I/O Buffer Size */
#else
#define CFG_CBSIZE 256 /* Console I/O Buffer Size */
#endif
#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */
#define CFG_MAXARGS 16 /* max number of command args */
#define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */
#define CFG_HZ 1000 /* decrementer freq: 1ms ticks */
#undef CONFIG_WATCHDOG /* watchdog disabled */
/*
* For booting Linux, the board info and command line data
* have to be in the first 8 MB of memory, since this is
* the maximum mapped by the Linux kernel during initialization.
*/
#define CFG_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux*/
#define CFG_HRCW_LOW (\
HRCWL_LCL_BUS_TO_SCB_CLK_1X1 |\
HRCWL_DDR_TO_SCB_CLK_1X1 |\
HRCWL_CSB_TO_CLKIN_4X1 |\
HRCWL_VCO_1X2 |\
HRCWL_CORE_TO_CSB_2X1)
#if defined(PCI_64BIT)
#define CFG_HRCW_HIGH (\
HRCWH_PCI_HOST |\
HRCWH_64_BIT_PCI |\
HRCWH_PCI1_ARBITER_ENABLE |\
HRCWH_PCI2_ARBITER_DISABLE |\
HRCWH_CORE_ENABLE |\
HRCWH_FROM_0X00000100 |\
HRCWH_BOOTSEQ_DISABLE |\
HRCWH_SW_WATCHDOG_DISABLE |\
HRCWH_ROM_LOC_LOCAL_16BIT |\
HRCWH_TSEC1M_IN_GMII |\
HRCWH_TSEC2M_IN_GMII )
#else
#define CFG_HRCW_HIGH (\
HRCWH_PCI_HOST |\
HRCWH_32_BIT_PCI |\
HRCWH_PCI1_ARBITER_ENABLE |\
HRCWH_PCI2_ARBITER_DISABLE |\
HRCWH_CORE_ENABLE |\
HRCWH_FROM_0X00000100 |\
HRCWH_BOOTSEQ_DISABLE |\
HRCWH_SW_WATCHDOG_DISABLE |\
HRCWH_ROM_LOC_LOCAL_16BIT |\
HRCWH_TSEC1M_IN_GMII |\
HRCWH_TSEC2M_IN_GMII )
#endif
/* System IO Config */
#define CFG_SICRH SICRH_TSOBI1
#define CFG_SICRL SICRL_LDP_A
/* i-cache and d-cache disabled */
#define CFG_HID0_INIT 0x000000000
#define CFG_HID0_FINAL CFG_HID0_INIT
#define CFG_HID2 HID2_HBE
#define CONFIG_HIGH_BATS 1 /* High BATs supported */
/* DDR 0 - 512M */
#define CFG_IBAT0L (CFG_SDRAM_BASE | BATL_PP_10 | BATL_MEMCOHERENCE)
#define CFG_IBAT0U (CFG_SDRAM_BASE | BATU_BL_256M | BATU_VS | BATU_VP)
#define CFG_IBAT1L (CFG_SDRAM_BASE + 0x10000000 | BATL_PP_10 | BATL_MEMCOHERENCE)
#define CFG_IBAT1U (CFG_SDRAM_BASE + 0x10000000 | BATU_BL_256M | BATU_VS | BATU_VP)
/* stack in DCACHE @ 512M (no backing mem) */
#define CFG_IBAT2L (CFG_INIT_RAM_ADDR | BATL_PP_10 | BATL_MEMCOHERENCE)
#define CFG_IBAT2U (CFG_INIT_RAM_ADDR | BATU_BL_128K | BATU_VS | BATU_VP)
/* PCI */
#ifdef CONFIG_PCI
#define CFG_IBAT3L (CFG_PCI1_MEM_BASE | BATL_PP_10 | BATL_MEMCOHERENCE)
#define CFG_IBAT3U (CFG_PCI1_MEM_BASE | BATU_BL_256M | BATU_VS | BATU_VP)
#define CFG_IBAT4L (CFG_PCI1_MEM_BASE + 0x10000000 | BATL_PP_10 | BATL_MEMCOHERENCE)
#define CFG_IBAT4U (CFG_PCI1_MEM_BASE + 0x10000000 | BATU_BL_256M | BATU_VS | BATU_VP)
#define CFG_IBAT5L (CFG_PCI1_IO_BASE | BATL_PP_10 | BATL_CACHEINHIBIT | BATL_GUARDEDSTORAGE)
#define CFG_IBAT5U (CFG_PCI1_IO_BASE + 0x10000000 | BATU_BL_16M | BATU_VS | BATU_VP)
#else
#define CFG_IBAT3L (0)
#define CFG_IBAT3U (0)
#define CFG_IBAT4L (0)
#define CFG_IBAT4U (0)
#define CFG_IBAT5L (0)
#define CFG_IBAT5U (0)
#endif
/* IMMRBAR */
#define CFG_IBAT6L (CFG_IMMR | BATL_PP_10 | BATL_CACHEINHIBIT | BATL_GUARDEDSTORAGE)
#define CFG_IBAT6U (CFG_IMMR | BATU_BL_1M | BATU_VS | BATU_VP)
/* FLASH */
#define CFG_IBAT7L (CFG_FLASH_BASE | BATL_PP_10 | BATL_CACHEINHIBIT | BATL_GUARDEDSTORAGE)
#define CFG_IBAT7U (CFG_FLASH_BASE | BATU_BL_256M | BATU_VS | BATU_VP)
#define CFG_DBAT0L CFG_IBAT0L
#define CFG_DBAT0U CFG_IBAT0U
#define CFG_DBAT1L CFG_IBAT1L
#define CFG_DBAT1U CFG_IBAT1U
#define CFG_DBAT2L CFG_IBAT2L
#define CFG_DBAT2U CFG_IBAT2U
#define CFG_DBAT3L CFG_IBAT3L
#define CFG_DBAT3U CFG_IBAT3U
#define CFG_DBAT4L CFG_IBAT4L
#define CFG_DBAT4U CFG_IBAT4U
#define CFG_DBAT5L CFG_IBAT5L
#define CFG_DBAT5U CFG_IBAT5U
#define CFG_DBAT6L CFG_IBAT6L
#define CFG_DBAT6U CFG_IBAT6U
#define CFG_DBAT7L CFG_IBAT7L
#define CFG_DBAT7U CFG_IBAT7U
/*
* Internal Definitions
*
* Boot Flags
*/
#define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH */
#define BOOTFLAG_WARM 0x02 /* Software reboot */
#if defined(CONFIG_CMD_KGDB)
#define CONFIG_KGDB_BAUDRATE 230400 /* speed of kgdb serial port */
#define CONFIG_KGDB_SER_INDEX 2 /* which serial port to use */
#endif
/*
* Environment Configuration
*/
#define CONFIG_LOADADDR 400000 /* default location for tftp and bootm */
#define CONFIG_BOOTDELAY 6 /* -1 disables auto-boot */
#undef CONFIG_BOOTARGS /* the boot command will set bootargs */
#define CONFIG_BAUDRATE 115200
#define CONFIG_PREBOOT "echo;" \
"echo Type \\\"run flash_nfs\\\" to mount root filesystem over NFS;" \
"echo"
#undef CONFIG_BOOTARGS
#define CONFIG_EXTRA_ENV_SETTINGS \
"netdev=eth0\0" \
"hostname=tqm834x\0" \
"nfsargs=setenv bootargs root=/dev/nfs rw " \
"nfsroot=${serverip}:${rootpath}\0" \
"ramargs=setenv bootargs root=/dev/ram rw\0" \
"addip=setenv bootargs ${bootargs} " \
"ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}" \
":${hostname}:${netdev}:off panic=1\0" \
"addtty=setenv bootargs ${bootargs} console=ttyS0,${baudrate}\0"\
"flash_nfs=run nfsargs addip addtty;" \
"bootm ${kernel_addr}\0" \
"flash_self=run ramargs addip addtty;" \
"bootm ${kernel_addr} ${ramdisk_addr}\0" \
"net_nfs=tftp 400000 ${bootfile};run nfsargs addip addtty;" \
"bootm\0" \
"rootpath=/opt/eldk/ppc_6xx\0" \
"bootfile=/tftpboot/tqm834x/uImage\0" \
"kernel_addr=80060000\0" \
"ramdisk_addr=80160000\0" \
"load=tftp 100000 /tftpboot/tqm834x/u-boot.bin\0" \
"update=protect off 80000000 8003ffff; " \
"era 80000000 8003ffff; cp.b 100000 80000000 40000\0" \
"upd=run load update\0" \
""
#define CONFIG_BOOTCOMMAND "run flash_self"
/*
* JFFS2 partitions
*/
/* mtdparts command line support */
#define CONFIG_JFFS2_CMDLINE
#define MTDIDS_DEFAULT "nor0=TQM834x-0"
/* default mtd partition table */
#define MTDPARTS_DEFAULT "mtdparts=TQM834x-0:256k(u-boot),256k(env),"\
"1m(kernel),2m(initrd),"\
"-(user);"\
#endif /* __CONFIG_H */