blob: 1876279abd49ff763b1a492bbed46ab04f1cbc80 [file] [log] [blame]
/*
* (C) Copyright 2007
* Stefan Roese, DENX Software Engineering, sr@denx.de.
*
* (C) Copyright 2004 Paul Reynolds <PaulReynolds@lhsolutions.com>
*
* See file CREDITS for list of people who contributed to this
* project.
*
* This program is free software; you can redistribute it and/or
* modify it under the terms of the GNU General Public License as
* published by the Free Software Foundation; either version 2 of
* the License, or (at your option) any later version.
*
* This program is distributed in the hope that it will be useful,
* but WITHOUT ANY WARRANTY; without even the implied warranty of
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
* GNU General Public License for more details.
*
* You should have received a copy of the GNU General Public License
* along with this program; if not, write to the Free Software
* Foundation, Inc., 59 Temple Place, Suite 330, Boston,
* MA 02111-1307 USA
*/
/************************************************************************
* katmai.h - configuration for AMCC Katmai (440SPe)
***********************************************************************/
#ifndef __CONFIG_H
#define __CONFIG_H
/*-----------------------------------------------------------------------
* High Level Configuration Options
*----------------------------------------------------------------------*/
#define CONFIG_KATMAI 1 /* Board is Katmai */
#define CONFIG_4xx 1 /* ... PPC4xx family */
#define CONFIG_440 1 /* ... PPC440 family */
#define CONFIG_440SPE 1 /* Specifc SPe support */
#define CONFIG_SYS_CLK_FREQ 33333333 /* external freq to pll */
#define CFG_4xx_RESET_TYPE 0x2 /* use chip reset on this board */
/*
* Enable this board for more than 2GB of SDRAM
*/
#define CONFIG_PHYS_64BIT
#define CONFIG_VERY_BIG_RAM
#define CONFIG_MAX_MEM_MAPPED ((phys_size_t)2 << 30)
/*
* Include common defines/options for all AMCC eval boards
*/
#define CONFIG_HOSTNAME katmai
#include "amcc-common.h"
#define CONFIG_BOARD_EARLY_INIT_F 1 /* Call board_pre_init */
#undef CONFIG_SHOW_BOOT_PROGRESS
/*-----------------------------------------------------------------------
* Base addresses -- Note these are effective addresses where the
* actual resources get mapped (not physical addresses)
*----------------------------------------------------------------------*/
#define CFG_FLASH_BASE 0xff000000 /* start of FLASH */
#define CFG_PERIPHERAL_BASE 0xa0000000 /* internal peripherals */
#define CFG_ISRAM_BASE 0x90000000 /* internal SRAM */
#define CFG_PCI_MEMBASE 0x80000000 /* mapped PCI memory */
#define CFG_PCI_BASE 0xd0000000 /* internal PCI regs */
#define CFG_PCI_TARGBASE CFG_PCI_MEMBASE
#define CFG_PCIE_MEMBASE 0xb0000000 /* mapped PCIe memory */
#define CFG_PCIE_MEMSIZE 0x08000000 /* smallest incr for PCIe port */
#define CFG_PCIE_BASE 0xe0000000 /* PCIe UTL regs */
#define CFG_PCIE0_CFGBASE 0xc0000000
#define CFG_PCIE1_CFGBASE 0xc1000000
#define CFG_PCIE2_CFGBASE 0xc2000000
#define CFG_PCIE0_XCFGBASE 0xc3000000
#define CFG_PCIE1_XCFGBASE 0xc3001000
#define CFG_PCIE2_XCFGBASE 0xc3002000
/* base address of inbound PCIe window */
#define CFG_PCIE_INBOUND_BASE 0x0000000000000000ULL
/* System RAM mapped to PCI space */
#define CONFIG_PCI_SYS_MEM_BUS CFG_SDRAM_BASE
#define CONFIG_PCI_SYS_MEM_PHYS CFG_SDRAM_BASE
#define CONFIG_PCI_SYS_MEM_SIZE (1024 * 1024 * 1024)
#define CFG_ACE_BASE 0xfe000000 /* Xilinx ACE controller - Compact Flash */
/*-----------------------------------------------------------------------
* Initial RAM & stack pointer (placed in internal SRAM)
*----------------------------------------------------------------------*/
#define CFG_TEMP_STACK_OCM 1
#define CFG_OCM_DATA_ADDR CFG_ISRAM_BASE
#define CFG_INIT_RAM_ADDR CFG_ISRAM_BASE /* Initial RAM address */
#define CFG_INIT_RAM_END 0x2000 /* End of used area in RAM */
#define CFG_GBL_DATA_SIZE 128 /* num bytes initial data */
#define CFG_GBL_DATA_OFFSET (CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE)
#define CFG_POST_WORD_ADDR (CFG_GBL_DATA_OFFSET - 0x4)
#define CFG_INIT_SP_OFFSET CFG_POST_WORD_ADDR
/*-----------------------------------------------------------------------
* Serial Port
*----------------------------------------------------------------------*/
#undef CONFIG_UART1_CONSOLE
#undef CFG_EXT_SERIAL_CLOCK
/*-----------------------------------------------------------------------
* DDR SDRAM
*----------------------------------------------------------------------*/
#define CONFIG_SPD_EEPROM 1 /* Use SPD EEPROM for setup */
#define SPD_EEPROM_ADDRESS {0x51, 0x52} /* SPD i2c spd addresses*/
#define CONFIG_DDR_ECC 1 /* with ECC support */
#define CONFIG_DDR_RQDC_FIXED 0x80000038 /* optimal value found by GDA*/
#undef CONFIG_STRESS
/*-----------------------------------------------------------------------
* I2C
*----------------------------------------------------------------------*/
#define CFG_I2C_SPEED 100000 /* I2C speed and slave address */
#define CONFIG_I2C_MULTI_BUS
#define CONFIG_I2C_CMD_TREE
#define CFG_SPD_BUS_NUM 0 /* The I2C bus for SPD */
#define IIC0_BOOTPROM_ADDR 0x50
#define IIC0_ALT_BOOTPROM_ADDR 0x54
#define CFG_I2C_MULTI_EEPROMS
#define CFG_I2C_EEPROM_ADDR (0x50)
#define CFG_I2C_EEPROM_ADDR_LEN 1
#define CFG_EEPROM_PAGE_WRITE_ENABLE
#define CFG_EEPROM_PAGE_WRITE_BITS 3
#define CFG_EEPROM_PAGE_WRITE_DELAY_MS 10
/* I2C RTC */
#define CONFIG_RTC_M41T11 1
#define CFG_RTC_BUS_NUM 1 /* The I2C bus for RTC */
#define CFG_I2C_RTC_ADDR 0x68
#define CFG_M41T11_BASE_YEAR 1900 /* play along with linux */
/* I2C DTT */
#define CONFIG_DTT_ADM1021 1 /* ADM1021 temp sensor support */
#define CFG_DTT_BUS_NUM 1 /* The I2C bus for DTT */
/*
* standard dtt sensor configuration - bottom bit will determine local or
* remote sensor of the ADM1021, the rest determines index into
* CFG_DTT_ADM1021 array below.
*/
#define CONFIG_DTT_SENSORS { 0, 1 }
/*
* ADM1021 temp sensor configuration (see dtt/adm1021.c for details).
* there will be one entry in this array for each two (dummy) sensors in
* CONFIG_DTT_SENSORS.
*
* For Katmai board:
* - only one ADM1021
* - i2c addr 0x18
* - conversion rate 0x02 = 0.25 conversions/second
* - ALERT ouput disabled
* - local temp sensor enabled, min set to 0 deg, max set to 85 deg
* - remote temp sensor enabled, min set to 0 deg, max set to 85 deg
*/
#define CFG_DTT_ADM1021 { { 0x18, 0x02, 0, 1, 0, 85, 1, 0, 58} }
/*-----------------------------------------------------------------------
* Environment
*----------------------------------------------------------------------*/
#define CONFIG_ENV_IS_IN_FLASH 1 /* Environment uses flash */
/*
* Default environment variables
*/
#define CONFIG_EXTRA_ENV_SETTINGS \
CONFIG_AMCC_DEF_ENV \
CONFIG_AMCC_DEF_ENV_POWERPC \
CONFIG_AMCC_DEF_ENV_PPC_OLD \
CONFIG_AMCC_DEF_ENV_NOR_UPD \
"kernel_addr=fff10000\0" \
"ramdisk_addr=fff20000\0" \
"kozio=bootm ffc60000\0" \
"pciconfighost=1\0" \
"pcie_mode=RP:RP:RP\0" \
""
/*
* Commands additional to the ones defined in amcc-common.h
*/
#define CONFIG_CMD_DATE
#define CONFIG_CMD_PCI
#define CONFIG_CMD_SDRAM
#define CONFIG_CMD_SNTP
#define CONFIG_IBM_EMAC4_V4 1 /* 440SPe has this EMAC version */
#define CONFIG_PHY_ADDR 1 /* PHY address, See schematics */
#define CONFIG_HAS_ETH0
#define CONFIG_PHY_RESET 1 /* reset phy upon startup */
#define CONFIG_PHY_RESET_DELAY 1000
#define CONFIG_CIS8201_PHY 1 /* Enable 'special' RGMII mode for Cicada phy */
#define CONFIG_PHY_GIGE 1 /* Include GbE speed/duplex detection */
/*-----------------------------------------------------------------------
* FLASH related
*----------------------------------------------------------------------*/
#define CFG_FLASH_CFI
#define CONFIG_FLASH_CFI_DRIVER
#define CFG_FLASH_EMPTY_INFO /* print 'E' for empty sector on flinfo */
#define CFG_FLASH_USE_BUFFER_WRITE 1 /* use buffered writes (20x faster) */
#define CFG_FLASH_BANKS_LIST {CFG_FLASH_BASE}
#define CFG_MAX_FLASH_BANKS 1 /* number of banks */
#define CFG_MAX_FLASH_SECT 1024 /* sectors per device */
#undef CFG_FLASH_CHECKSUM
#define CFG_FLASH_ERASE_TOUT 120000 /* Timeout for Flash Erase (in ms) */
#define CFG_FLASH_WRITE_TOUT 500 /* Timeout for Flash Write (in ms) */
#define CFG_ENV_SECT_SIZE 0x20000 /* size of one complete sector */
#define CFG_ENV_ADDR (CFG_MONITOR_BASE-CFG_ENV_SECT_SIZE)
#define CFG_ENV_SIZE 0x4000 /* Total Size of Environment Sector */
/* Address and size of Redundant Environment Sector */
#define CFG_ENV_ADDR_REDUND (CFG_ENV_ADDR-CFG_ENV_SECT_SIZE)
#define CFG_ENV_SIZE_REDUND (CFG_ENV_SIZE)
/*-----------------------------------------------------------------------
* PCI stuff
*-----------------------------------------------------------------------
*/
/* General PCI */
#define CONFIG_PCI /* include pci support */
#define CONFIG_PCI_PNP 1 /* do pci plug-and-play */
#define CONFIG_PCI_SCAN_SHOW 1 /* show pci devices on startup */
#define CONFIG_PCI_CONFIG_HOST_BRIDGE
/* Board-specific PCI */
#define CFG_PCI_TARGET_INIT /* let board init pci target */
#undef CFG_PCI_MASTER_INIT
#define CFG_PCI_SUBSYS_VENDORID 0x1014 /* IBM */
#define CFG_PCI_SUBSYS_DEVICEID 0xcafe /* Whatever */
/* #define CFG_PCI_SUBSYS_ID CFG_PCI_SUBSYS_DEVICEID */
/*
* NETWORK Support (PCI):
*/
/* Support for Intel 82557/82559/82559ER chips. */
#define CONFIG_EEPRO100
/*-----------------------------------------------------------------------
* Xilinx System ACE support
*----------------------------------------------------------------------*/
#define CONFIG_SYSTEMACE 1 /* Enable SystemACE support */
#define CFG_SYSTEMACE_WIDTH 16 /* Data bus width is 16 */
#define CFG_SYSTEMACE_BASE CFG_ACE_BASE
#define CONFIG_DOS_PARTITION 1
/*-----------------------------------------------------------------------
* External Bus Controller (EBC) Setup
*----------------------------------------------------------------------*/
/* Memory Bank 0 (Flash) initialization */
#define CFG_EBC_PB0AP (EBC_BXAP_BME_DISABLED | \
EBC_BXAP_TWT_ENCODE(7) | \
EBC_BXAP_BCE_DISABLE | \
EBC_BXAP_BCT_2TRANS | \
EBC_BXAP_CSN_ENCODE(0) | \
EBC_BXAP_OEN_ENCODE(0) | \
EBC_BXAP_WBN_ENCODE(0) | \
EBC_BXAP_WBF_ENCODE(0) | \
EBC_BXAP_TH_ENCODE(0) | \
EBC_BXAP_RE_DISABLED | \
EBC_BXAP_SOR_DELAYED | \
EBC_BXAP_BEM_WRITEONLY | \
EBC_BXAP_PEN_DISABLED)
#define CFG_EBC_PB0CR (EBC_BXCR_BAS_ENCODE(CFG_FLASH_BASE) | \
EBC_BXCR_BS_16MB | \
EBC_BXCR_BU_RW | \
EBC_BXCR_BW_16BIT)
/* Memory Bank 1 (Xilinx System ACE controller) initialization */
#define CFG_EBC_PB1AP (EBC_BXAP_BME_DISABLED | \
EBC_BXAP_TWT_ENCODE(4) | \
EBC_BXAP_BCE_DISABLE | \
EBC_BXAP_BCT_2TRANS | \
EBC_BXAP_CSN_ENCODE(0) | \
EBC_BXAP_OEN_ENCODE(0) | \
EBC_BXAP_WBN_ENCODE(0) | \
EBC_BXAP_WBF_ENCODE(0) | \
EBC_BXAP_TH_ENCODE(0) | \
EBC_BXAP_RE_DISABLED | \
EBC_BXAP_SOR_NONDELAYED | \
EBC_BXAP_BEM_WRITEONLY | \
EBC_BXAP_PEN_DISABLED)
#define CFG_EBC_PB1CR (EBC_BXCR_BAS_ENCODE(CFG_ACE_BASE) | \
EBC_BXCR_BS_1MB | \
EBC_BXCR_BU_RW | \
EBC_BXCR_BW_16BIT)
/*-------------------------------------------------------------------------
* Initialize EBC CONFIG -
* Keep the Default value, but the bit PDT which has to be set to 1 ?TBC
* default value : 0x07C00000 - 0 0 000 1 1 1 1 1 0000 0 00000 000000000000
*-------------------------------------------------------------------------*/
#define CFG_EBC_CFG (EBC_CFG_LE_UNLOCK | \
EBC_CFG_PTD_ENABLE | \
EBC_CFG_RTC_16PERCLK | \
EBC_CFG_ATC_PREVIOUS | \
EBC_CFG_DTC_PREVIOUS | \
EBC_CFG_CTC_PREVIOUS | \
EBC_CFG_OEO_PREVIOUS | \
EBC_CFG_EMC_DEFAULT | \
EBC_CFG_PME_DISABLE | \
EBC_CFG_PR_16)
/*-----------------------------------------------------------------------
* GPIO Setup
*----------------------------------------------------------------------*/
#define CFG_GPIO_PCIE_PRESENT0 17
#define CFG_GPIO_PCIE_PRESENT1 21
#define CFG_GPIO_PCIE_PRESENT2 23
#define CFG_GPIO_RS232_FORCEOFF 30
#define CFG_PFC0 (GPIO_VAL(CFG_GPIO_PCIE_PRESENT0) | \
GPIO_VAL(CFG_GPIO_PCIE_PRESENT1) | \
GPIO_VAL(CFG_GPIO_PCIE_PRESENT2) | \
GPIO_VAL(CFG_GPIO_RS232_FORCEOFF))
#define CFG_GPIO_OR GPIO_VAL(CFG_GPIO_RS232_FORCEOFF)
#define CFG_GPIO_TCR GPIO_VAL(CFG_GPIO_RS232_FORCEOFF)
#define CFG_GPIO_ODR 0
#endif /* __CONFIG_H */